Search Documents

By Edward E. Tate

This is a report on the design, development, and manufacture of a prototype roof bolting machine for high rise applications. The machine is designed to traverse a 32 inch entry and rebolt a roof fall area to a height of 28 feet 10 inches. Covered in the report is a chronology of the project, an explanation of the design problems, and a description of their solutions. The report concludes that the equipment as designed is suitable for the purpose intended and further testing is recommended.

Jan 1, 1981

By J. B. Zadra

After the discovery of the rare-earth mineral deposit in the Clark Mountain area near Mountain Pass, San Bernardino County, Calif., two samples wore obtained through the Mining Division of the Bureau of Mines for investigation of possible method of concentration. Three other samples were received later from different locations in the same area. The rare-earth mineral in this ore had been identified by E. T. Schonk as bastnaesite, a fluocarbonate of the rare-earth metals containing cerium, lanthanum, praseodymium, thorium, uranium, etc. Associated with the bastnaesite were barite, silica, and some calcite. The bastnaesite contained a small amount of iron as a coloration and some manganese. Twenty to fifty percent of the weight of the samples studied was bastnaesite, or ten to twenty-five percent total rare-earth oxides; about half was cerium oxide. Apparently, none of this mineral occurred in pure form. Even the highest-grade particles 'wore contaminated by fine, interlocked grains of barite, calcite, and silica; barite contamination predominated, and the barite was interlocked with varying amounts of bastnaesite. While the specific gravities of pure bastnaesite and barite (approximately 5.0 and 4.50 respectively) differ enough to allow separation by gravity, the interlocking of the minerals nullified this difference. Consequently, only a partial separation could be made by gravity concentration. The extremely fine grained texture of most of the ore prevented grinding to a size that would make concentration by flotation practicable; a partial separation of barite by this means was effected.

Jan 1, 1952

By James R. Kerr

Although metallurgical benefits of processing metals in a vacuum or reduced atmosphere have been realized for a hundred years, the problem of creating a vacuum in the range from 10-0 to 10-4 mm. of mercury in a moderately sized furnace chamber has been difficult to solve. The demand for these and lower pressures, with the advent of World War II, for separating the fission-able uranium isotope from its stable twin by the electromagnetic process, gave impetus to developing pumps capable of delivering extremely low pressures. With the release of data by the Atomic Energy Commission on methods of securing high vacuum in large equipment, steel companies took the initiative, and the growth of the vacuum-melting industry was assured. Vacuum-induction melting of steel in the United States began on a small scale in early 1945 and in 10 years grew to 60,000 pounds per month or 720,000 pounds per year. The years following 1954 showed tremendous expansion, culminating in 1958 in a capacity of more than 36 million pounds.

Jan 1, 1962

By R. R. Sayers

Under compuision of the present urgency to implement the President's promise to make the United States the arsenal for the democracies there is a tendency to demand a relaxation of restrictions on hours of labor and to speed up all industrial processes. The pressure is the more insistent with growing realization of the importance of the time factor in the success- ful prosecution of the war effort and the lack of skilled workers due to (2) operation of the draft, lack of an apprentice system in industry, and loss of skill by workers unemployed for long periods during the depression. With "total" war such as it is today the probabilities are that everyone will be required to exert greater effort (in many instances in activities to which they are unaccustomed) for longer periods than ever before has been necessary. The question arises, "What will be the aftereffects as well as the immediate effects on health, safety, and efficiency?" A review of the literature leaves the impression that this question has not been an- swered completely, especially as regards the ultimate effects. Mechanization, speeding up of industrial processes, mass produc- tion, and the small industrial concerns present many problems to indus- trial medicine. Does the tendency to expect the worker to produce at full speed all the time he is on the job decrease the effectiveness of the shorter working hours and cause undue fatigue, loss of efficiency, and increased accident proneness? The answer is important as this condition is likely to be intensified by the exigencies of the present emergency. According to Viteles (1)3, The increased tension under such conditions of work appears to offset the savings in muscular force made pos- sible by the machine. The tension, the speed, the subject- tion to specialization of work and a rhythm uncontrolled by the individual promote fatigue, characterized by a "decrease in the power to work, a decrease in pleasure taken in work, and a decrease in the enjoyment of the hours spent away from work."' The crowding of workers in temporary structures without proper provision for comfort and health may add greatly to the general fatigue factors already present in many industrial establishments. In 1932 Lockhart (2) stated that the production and maintenance of a healthy, satisfied industrial population is the most urgent necessity, involving problems so serious as to constitute a national task too great economically to be relegated to industrial concerns. If this was true in 1932, it must be doubly so today.

Jun 1, 1942

By Harold H. Fukubayashi

The effect of various zinc electrowinning solution impurities on the surface morphology of deposited zinc was investigated. Impurities studied included Al, Ag, Cd, Co, Cr, Cu, Ge, Mn, Ni, Sb, Sn, Ti, Pb02, PbSO4, and HC1. Also, the effect of animal glue, gum arabic, and Na2SiO3 additives on the deposited zinc surface structure was studied. Results were compared with deposits from a pure electrolyte consisting of H2SO4 and Zn+2, 200 and 65 gpl, respectively. Zinc was deposited on a Al cathode, 99.9 pct pure, using Pt anodes. Time, temperature, current density, and impurity concentrations were con¬troller The bulk of the tests were conducted at 40° C and 75 A/ft2 (82 mA/cm2). A scanning electron microscope (SEM) was used to examine the surface morphology. X ray diffraction techniques were used to determine crystal orientation and nondispersive X-ray spectrometer analyses were employed in an attempt to locate impurity concentrations on the zinc deposit when pitting or re-solution occurred. The impurities were categorized by their effect on current efficiency, morphology, and apparent mechanism of H2 evolution from the cathode.

Jan 1, 1974

By Robert R. Stein

Using an automated drill test fooure, the U.S. Bureau of Mines measured the sound power levels produced by a small, pneumatic, rotary roof drill. A series of tests was conducted to determine (1) the relative effectiveness of several drill muffling schemes and (2) the relationship between drill sound power and pneumatic power supplied to the drill. The influence of rotation rate (i.e., airflow) and feed thrust on the penetration rate of the drill was also noted.

Jan 1, 1989

By D. J. Dollhopf

A week-long selective overburden handling dragline op ration was conducted at a strip mine near Colstrip, Montana. The objective of the demonstration was to hvdrologically isolate a saline overburden zone during placement in the spoil piles. The saline zone had concentrations considered inimical to successful reclamation and was potentially dangerous to future water quality in the spoils aquifer. The zone was identified after review of chemical data for overburden samples collected from the intense 60 m grid drilling pattern. The saline zone in the overburden was: 1) handled in a normal manner; 2) segregated and buried; and 3) segregated, buried, and covered with a relatively impermeable 1.0 m thick clay cap. The method used to formulate this demonstration, the demonstration itself, and the monitoring and evaluation techniques are described in this report. Observation wells were installed to monitor ground water in the overburden, Rosebud coal, and McKay coal. Data from these wells were, used to estimate post reclamation water levels and to evaluate recharge and water movement characteristics in the vicinity of the demonstrations. The inimical zone was successfully handled in a selective manner with a minimum of delays. Economic analysis indicated cost of these selective burial operations to be about 1.1 to 1.5 times the cost of the normal operation at this particular mine site. Long term monitoring will be required to evaluate the effectiveness of these handling techniques in hydrologically isolating undesirable overburden materials.

Jan 1, 1977

By A. J. Kraemer

The twenty-fourth of a series of semiannual surveys pertaining to motor gasoline marketed in the United States was made by the Bureau of Mines in August, 1931. The first part of a report giving the results of that survey as they pertain to specification data is given in this paper. A companion report, Part II, is in preparation and will discuss the results of other determinations made on the samples, including octane number ratings on the individual samples (to be made by the Bureau of Standards) and results of the determination of gravity, color, doctor test, and "gum" content by the copper dish method and the Bureau of Mines steam-oven method. The retail price and the tax at the time each sample was taken will also be reported.

Jan 1, 1932

By G. R. Smith

This report describes research carried out by the Bureau of Mines to develop new technology for electrorefining metals at much higher current densities than those normally used in commercial practice, preliminary studies using rotating-ring and cylinder electrodes to increase the mass transport of copper are discussed. Following this work, single- and multichannel cells were developed that utilized a high electrolyte flow in the channels formed by the anode-cathode pairs. Using these cells, copper was successfully refined at current densities in the range of 70 to 300 amp/ft2. The effects of flow rate, electrolyte composition, and grain-refining and leveling agents on the morphology and purity of electrodeposited copper were determined.

Jan 1, 1979

By N. E. Hanna

Originally developed for use in coal mines where on-shift blasting with explosives was prohibited, compressed-air blasting has been used for the past 15 years as a substitute for fixed explosives. With the current commercially available compressed-air systems -Airdox and Armstrong -coal is dislodged by a high-pressure discharge of air from a pressurized shell placed in the coal borehole. In the original systems stationary compressors were mounted on the surface or in the underground ventilated areas. These proved so successful that a mobile compressor unit was developed for use at the working face. Because of the possibility that such a unit might operate in a gassy atmosphere, the Bureau of Mines has investigated the hazards associated with operation under conditions where firedamp could accumulate in explosive concentrations. ACKNOWLEDGMENTS Grateful acknowledgment is made of cooperation of C. E. Carter, H. R. Hiller, R. E. Kennedy, H. Kohn, H. D. Metzinger, J. Mahoney, J. Nickovich, G. So Scott and I. Spolan in the experimental work.

Jan 1, 1956

By Jr. Frank Parrish

This report describes the performance of 17 selected water-injection projects producing from Pennsylvanian-and Permian-age reservoirs. Illustrations depict reservoir structure and thickness, and production and injection history. A selected bibliography of publications pertaining to area oil recovery and geology is included. Tabulations of field and reservoir data reveal marked differences in the projects. Increased oil recovery resulted from injecting water in most cases; however, seven projects recovered less oil than the operators anticipated. Oil recovery by water injection ranged from 0.2 to 262 bbl per acre ft, or 0.1 to 22.5 pct of the initial stock-tank oil in place. Major reasons suggested for poor performance include: (1) Adverse directional horizontal permeability, (2) channeling of injected water through fractures or zones of high permeability, and (3) lack of containment of injected water. One 330-foot-deep project is among the first successful shallow water-floods in north Texas. Another project is the first successful Canyon sand-stone waterflood reported in the area. Previous gas injection in two Cisco sandstone projects did not prevent the reservoirs from responding favorably to waterflooding.

Jan 1, 1965

By G. L. Humphrey

Although thermodynamic data for ferrous oxide are among the most important in extractive metallurgy, adequate values have not been available until quite recently. The older data suffered not only from the usual experimental difficulties but especially from lack of the knowledge that ferrous oxide of stoichiometrical composition does not exist as a single, thermodynamically stable crystalline phase under any circumstances. This paper reports new experimental data on the heat of formation of ferrous oxide by two methods (combustion calorimetry and solution calorimetry), employing material of unequivocal composition. The results are compared with values obtained from data for the hydrogen reduction, carbon monoxide reduction, and disproportionation reactions of ferrous oxide, and a best value is selected. A table of heat and free energy of formation values of ferrous oxide to 2,000°K is given. These values are combined with available data for water, carbon monoxide, and carbon dioxide to obtain theoretical heats and free energies of reduction corresponding to the selected heat of formation. Hydrogen and carbon monoxide reduction equilibria are compared, and the differences in trend with temperature and the percentage utilization of the reductants are considered.

Jan 1, 1952

By L. A. Haas

The Bureau of Mines, in cooperation with three Minnesota agencies (Department of Natural Resources, Geological Survey, and the Iron Range Resources and Rehabilitation Board), investigated the potential of using glacial lake clay from Minnesota, as well as other areas, as a binder for iron ore pellets. The best clay-characterizing procedures for predicting binder effectiveness were the cation exchange capacity (CEC) using the methylene blue method and the plate water absorption test (PWAT). The best clay binder was found in the Red River Valley. However, compared to a typical western bentonite at the 0.5-pct-addition level, addition of about 2 pct Minnesota clay was required to obtain comparable unfired (green) pellet strengths. Soda ash addition only slightly improved the binding properties of Minnesota clay, but considerable improvement was obtained by the addition of a small quantity of water absorbing organic compounds. For example, with a mixture of 0.5 pct Minnesota clay or paint rock and 0.1 pct pregelatinized starch, the unfired and fired physical pellet properties were about the same as with 0.5 pct of typical western bentonite. The reduction rate at the 40-pct reduction level and the percentage of plus 6.3-mm particles from the reduction disintegration index test were also about the same.

Jan 1, 1987

By Edward W. Parsons

To determine in what part and to what extent creep or movement exists in an installed rock-bolt anchor and the effect of the creep or bleedoff on the tension load on a rock bolt, as well as the effect of normal mining activity on the rock-bolt load and anchor, the Bureau of Mines conducted tests in the laboratory and in two mines using four types of expansion-shell anchors, the wedge bolt, and in one mine, explosive-anchored rock bolts. Specially mounted heavy-duty springs, calibrated to obtain load readings from spring movement, were installed on the test bolts to prevent a drastic reduction in tension load caused by slipping or seating of the anchor. A dial gage, reading to 0.0001 inch, measured movement of the anchor shell against the rock and seating of the anchor wedge plug in the shell. While all bolts had electrical resistance strain gages for load reading, only readings from the laboratory tests were used because those from the field tests were erratic. The tests revealed that most load loss resulting from static loading is due to the slippage and seating of the serrations on the anchor shell into the drill-hole wall. Dynamic loading, primarily from sudden shocks from nearby blasting, and possibly from ground movement or mining activity, will cause the anchor wedge plug to seat in the anchor shell.

Jan 1, 1969

By H. A. Dierks

The work and costs involved in controlling three large fires in abandoned mines in the anthracite region of Pennsylvania are presented in detail. The work was done under authority of Public Law 89-4. Three basic control techniques were successfully employed by the Bureau of Mines: (1) forming underground fire-containing barriers by systematically flushing incombustible material into mine voids, (2) excavating an isolation trench around the fire area, and (3) complete excavation of hot and burning material in the fire area. When methods 2 and 3 were used, the excavations were subsequently back- filled with incombustible material. Preliminary location of fire perimeters by the standard use of patterned 6- and 8-inch-diameter boreholes is discussed. Investigations into air-borne infrared scanning, shallow subsurface thermal anomalies, and the use of helium to trace the movement of mine air currents are covered. Although they are costly and time consuming, boreholes have proven to be the most efficient means to date of obtaining necessary subsurface fire data. Infrared scanning was ineffective in delineating fires under more than 30 feet of cover. Helium-tracing was shown to have a good potential for determining possible hazards to adjacent residential areas from traveling mine fire gases.

Jan 1, 1971

By Scott W. Hazen, Richard F. Link, George S. Koch

The Mi Vida mine , Big Indian district , San Juan County , Utah , is in an ore deposit of uranium and vanadium minerals disseminated in certain sedimentary beds of the Triassic Chinle formation . Statistical analysis of assays of samples taken from the ore body affords an estimate of the grade of the ore body and provides a prediction about the direction of best mineralization beyond the sampled area . The basic data analyzed are assay results for uranium ( Uз Og ) , vanadium (V₂O ) , and lime (CaO ) from 225 channel samples cut at 79 sample points . Through the use of appropriate statistical methods , particularly regression analysis , the grade of ore may be estimated more precisely than by conventional means , and the most favorable direction to extend the mine may be predicted . Frequency distributions of assay residuals for uranium , vanadium , and lime are compared to frequency distributions of assays without regard to trend . Correlations among these variables are obtained and interpreted . The statistical methods employed illustrate certain techniques that may be used to analyze assay data from ore deposits in general .

Jan 1, 1964

By C. C. Hwang

The Bureau of Mines made time-dependent calculations to determine the size of a stationary source fire within a ventilated duct (or passage-way) necessary to ignite a combustible duct liner. The objective of this work was to gain more understanding of what occurs in duct fires and to determine critical conditions for ignition and propagation of mine fires. Heat transfer to the combustible surface includes both convective and radiated components, while the heat is conducted into the combustible and reradiated to the surroundings. The combustible is assumed to ignite when the net heat transfer to its surface is sufficient to raise the surface temperature to some minimum temperature, defined as the ignition temperature. A nondimensional parameter, which characterizes the source-fire intensity in the presence of ventilation flow, emerges as a parameter for a criterion of the critical conditions. The results of these calculations indicated that the minimum fire size necessary for ignition increases with the ventilation rate and duct cross section. These results are compared with experimental results obtained from fires in a 0.8-by 0.8-by Il-m-long duct and a full-scale gallery (2.4-by 2.4-by 65-m). Agreement between the theory and the experiment is good.

Jan 1, 1988

By J. C. Gerdeen

A new analytical model for the shear stiffness at a joint of the fully-grouted resin roofbolt is developed using the Theory of Elasticity and an analogy to a beam on an elastic foundation, Gerdeen [2]. The model developed in this study treats the elastic foundation modulus of the resin as being composed of both an elastic rock and an elastic resin. All previous attempts have neglected the elasticity of the rock and treated only the resin. A three dimensional finite element model of the bolt-resin-rock system is developed also and comparisons are made between the predictions made by it and the analytical solution. It is found that the agreement between the two representations ranges between 1.2% and 10.5%, with the greater differences being observed for systems of very large or very small bolt diameters and resin annulus thicknesses. Since such configurations are not the rule in practice parameter studies are performed using the analytical solution with the finite element solution being used as a check. For a 0.75 in. bolt, a resin annulus thickness of 0.1375 in., a resin with E = 7 x 105 psi and -1) = 0.210, and a rock of modulus E = 6.8 x 106 psi and V = 0.159 the shear stiffness is found to be 1.220 x 106 lb,/in, from the analytical solution and 1.245 x 106 lb,/in, from the finite element model. Applying the finite element model to the problem of the axial stiffness of the fully-grouted resin roofbolt a value of 6.002 x 106 lb./in. is obtained which proves to be at least 50% higher than any of the now existing analytical predictions.

Jan 1, 1976

By George C. Price

The Bureau of Mines conducted this study in the Roslyn No.5 coalbed in the State of Washington to determine the feasibility of mining hydraulically the portion of the coalbed that was steeply pitching. All of the experimental mining was done while advancing raises and rooms. A Bureau-developed hydraulic mining machine was used successfully in the pitching coalbed. It consisted of a remotely controlled monitor mounted on a self-advancing roof support unit of the type commonly used for roof support in longwall mining systems. The coal cutting rates averaged 0.73 and 0.54 ton per minute in raise and room mining, respectively, while using water volumes up to 230 gpm at a pressure of 4,000 psig. Productivity averaged 4.7 and 5.2 tons per man-shift for raise and room mining, respectively, compared with 7.5 and 8.5 tons per man-shift, respectively, by conventional hand mining methods.

Jan 1, 1965

By Harold M. Smith

Natural gas has been used as a fuel and source of energy almost from its discovery, but its use as a chemical raw material may be said to have begun in 1918, when Brooks and Humphrey3/ showed. presence of alcohols in the diluted acid oil obtained by the sulfuric acid-treatment of cracked petroleum distillates. However, development of the utilization of natural gas for chemical syntheses was slow, partly because erroneous ideas existed regarding the nonreactivity of tine hydrocarbons composing natural gas. Data accumulated by petroleum chemists throughout the world, particularly since about 1930, have shown that these hydrocarbons will react when activated by the effects of heat, pressure, chemical reagents, and light; also that the reactions can be made to proceed of practicable speeds and to provide good yields of useful products with moderate operating conditions, especially if catalysts are employed. As those results became known, the possibility of a synthetic organic chemical industry based upon these reactions became apparent, and today this industry is large and growing rapidly in importance. In this paper the story of the manufacture of chemical products from natural gas is told simply in graphic form. The industry is developing so rapidly that soma products may have been omitted, but every effort has been made to include all that are important or likely to become so. The difficulty of keeping information of this tape up to date is shown by reference to an information circular4/ or, the sore subject published by the Bureau of Mines in 1930, in which the important products are shown on a single chart, where as five charts are employed for the cane purpose at present.

Jan 1, 1940