Search Documents

By J. E. Fraley

This report describes the preliminary results of a Bureau program to develop and test an inexpensive grout for full-column support of roof bolts. Various inorganic grouts were tested in both cartridge and slurry form. Tests were also performed on methods of water packaging and on the effect of fillers on the grout strength. Results showed that some grouts had poor early strength and exceptional mid-to long-term strength. Laboratory tests have shown that rapid-setting inorganic grout could be an economical replacement for resin bolts if the short-term strength could be increased. Further development to improve its early strength would need to be tested in the laboratory and underground to prove its potential for the mining industry.

Jan 1, 1987

By L. C. George

The Bureau of Mines measured vapor pressures of selected mixtures in the binary system SnCla-ZnC12 by the static pressure method. Equations expressing the vapor pressure) and the heat and free energy of vaporization) as functions of temperature were developed by numerical analysis based on the sigma-plot method. It was found that the vapor pressure of any SnCl2-ZnCl2 mixture) at any temperature within the range of this investigation) could be accurately calculated from the derived values for the heat and free energy of vaporization for the mixture, with a probable error of 0.01 cm Hg or less.

Jan 1, 1967

By J. R. Thoenen, B. H. Clemmons, A. H. Reed

"INTRODUCTION AND SUMMARYOverall red-ore reserves in the Birmingham, Ala., area were estimated in 1910 by E. F. Burchard 4/. Since then mining has progressed into areas classed by Burchard as ""unavailable for exploitation"" under conditions existing at that time. This is understandable when it is considered that red iron ore was valued at $1.19 a gross ton at the mine in Birmingham in 19102/ and by 1948 had risen 300 percent; 6/ that skips had replaced cars in slope haulage; that mechanical loading and rubber-tired haulage had replaced hand loading and mule or locomotive haulage; and that other more efficient mining methods had been introduced. Intensive study during the intervening 40 years has been given to ways and means for upgrading the low-grade ores in the area and combining or blending them with raw red and brown ores for improved blast-furnace feed.It is reasonable to expect that future progress in mining efficiency and increased knowledge of the beneficiation characteristics of marginal ores will permit extraction of red-iron minerals now considered uneconomic.The Bureau of Mines has undertaken to restudy iron-ore reserves of the Birmingham area to determine what tonnage and grades of mineral are present; what is necessary to make them amenable to mining; what further advancement is possible in beneficia¬tion methods; and where increased production may be obtained in the area if and when required. This study has been underway for the past 2 years, but research into the beneficiation of marginal ores has been in progress at the Southern Experiment Station for the past 30 years. Many results of that research have been adopted in commercial practice in the area. Other results have not been published but are pre¬sented here in condensed form as an important factor in assessing marginal deposits with respect to their importance as ore reserves.An interim discussion of the salient features of past history and progress, as well as the data developed during the years of research in beneficiation at this station and the present field investigation, will make for a better understanding of the present position as well as be useful in evaluating future potentialities. Discussion in this paper is confined to the main Birmingham Basin area, which contains the largest concentration of hematite ores in the district."

Jul 1, 1953

By T. H. Miller

An attempt has been mace in this publication to present annotated references to all articles pertaining, to ore dressing that were published during 1931 and 1932; in a few instances reference is made to articles published prior to 1931 where the articles have not been included in previous bibliography appended to the annual statistical discussions of ore concentration published by the Bureau of Mines. Articles have been taken from more than 75 periodicals, journals, serials, etc., and 423 articles are abstracted herewith. A number of these abstracts, particularly those appearing in foreign publications, have been taken from Chemical Abstracts (published by the American Chemical Society, Easton, Pa.), the general use of which the authors wish to acknowledge. Other annotations were taken directly from the original publications. The entire field of ore dressing has been included in the bibliography and articles dealing with crushing, grinding classification, concentration, thickening, and filtration have been included, as well as on amalgamation, cyanidation, leaching, magnetic concentration, washing, etc., and on theory and laboratory operation. The articles are arranged in alphabetical order by authors. Lack of printing funds prohibited the inclusion of a subject index.

Jan 1, 1934

By Arno C. Fieldner

The determination and publication of data o the chemical and physical properties of American coals have been primary functions of the Bureau of Mines since its creation in 1910. In recent years this program has been expanded to meet increasing needs for information on the suitability of coals for the production of coke, gas, and byproducts, and within the last year an experimental coal-hydrogenation plant has been completed. With this addition, the Bureau is able to cover every phase of coal utilization, including combustion, carbonization, liquefaction, and complete gasification. The need for this information is increasing not only to meet the requirements of consumers but also to give the data required to establish the classification and minimum selling price of coal by the National Bituminous Coal Commission.

Jan 1, 1938

By S. Kodama

Starting on a small scale, the equipment for processing synthesis gas to form liquid hydrocarbons was expanded to handle 100 m) 3/hr. This reactor was successfully designed and constructed, and a basis for future design methods was established. Because, however, this work was carried out on an empirical basis, it is felt that a more thorough theoretical study should be made in an effort to increase the efficiency of the process, particularly in the development of a simpler converter.

Jan 1, 1951

By R. Lusignea

This report describes the development of a device for the nondestructive testing of resin grouted roof bolts by means of mechanical frequency response. Various alternative methods were evaluated and the mechanical frequency response method was selected. An interactive program of design, testing, and development culminating in the current prototype instrument demonstrated the capabilities of the method and suggested potential applications of the instrument. The resin bolt testing device utilizes a swept frequency dynamic compliance measurement in the 1 to 2 kHz range which is interpreted by an electronic signal processor to give a "GO" or "NO GO? readout. Field tests have shown that the device can reliably determine the bond quality of the front half of the bolt (nearest the roof surface). Tests were carried out on both experimentally installed bolts and typical mine bolts installed by a conventional bolting machine. The development program has led to recommendations for improvement of the prototype and future development work.

Jan 1, 1979

By John C. Holtz

"The Federal Bureau of Mines serves the mining industry by approving equipment that is designed to prevent explosion, fire, shock, or toxic hazards in mines when such equipment is used and maintained in a proper manner, through research, consultation, testing, and inspection, the Bureau studies machinery and component parts submitted by manufacturers and others. Before receiving the Bureau's approval as permissible for safe use in mines, equipment must pass exacting tests and must meet strict requirements established through research and experience and listed in the Bureau's various permissibility schedules. An important phase of the Bureau's research is the testing of diesel engines.Mobile diesel-powered equipment can be used safely in underground noncoal mines and tunnels when mechanical ventilation is provided to dilute and remove the exhaust gas and to replenish oxygen in the underground atmosphere. Safe ventilation is determined by suitable tests of each engine used in a diesel machine. This ventilation cannot be predicted safely, accurately, and economically from any general empirical relationship.In determining safe ventilation, the quantities of carbon dioxide, carbon monoxide, and oxides of nitrogen generated by a diesel engine must be ascertained. These quantities are related to the displacement of the engine, its speed of operation, the design of the combustion chamber, and the fuel:air ratio needed to produce useful power. At overrich fuel:air ratios, all diesel engines generate excessive quantities of toxic carbon monoxide and smoke. The results of engine tests are used to determine a maximum fuel-injection rate at or below which carbon monoxide can be controlled by a reasonable ventilation and smoke is essentially eliminated. Toxic oxides of nitrogen are related to fuel:air ratio and the design of the combustion chamber. Their concentration in the exhaust cannot be controlled by engine adjustments, and each engine appears to have individual characteristics concerning formation of these oxides. Production of oxides of nitrogen frequently is the most important factor in determining safe ventilation."

Oct 1, 1959

By David E. Nicholson

In a Bureau of Mines investigation of the dynamic compaction of mine hydraulic backfills, two basic forms of mechanical vibration inducers were used and compared for effectiveness of compaction. Internal compaction, using concrete probe vibrators of various sizes, and external compaction, using plate vibrators} were studied and evaluated for use in underground stopes. An aluminum plate, which was light and displaced sufficient volume to remain afloat in fluid fill, and a steel plate were both used in the external compaction tests. Efficiency of compaction was better in studies conducted with internal probe vibrators. Tests were conducted in an underground backfilled stope with three different-sized probe vibrators (2-, 4-, and 6-inch-diameter) to determine an approximate area of influence. Results showed the areas of influence to be approximately 3, 4, and 5 feet in diameter, respectively, for the three different probes. Physical properties of hydraulic slurries were determined; preferred grain-size distributions, water exudation properties, and water contents of hydraulic slurries are reported. The best compaction results were obtained with moderately well-graded, fully saturated backfills, with slow rates of water exudation, which were capable of remaining in a semifluid state during the compaction process.

Jan 1, 1967

By Larry A. Haas

The chemistry of current or potential SO2 removal processes can be placed into four categories: (1) reduction, (2) Liquefaction, (3) direct dissolution, and (4) oxidation. Methods that involve reducing SO2 to elemental sulfur appear promising since this product can be easily handled, shipped, and stock- piled. Unfortunately, SO2 cannot always be reduced directly when other oxidizing agents are present. Thermodynamic data indicate that some oxidizing reagents will also consume reductant at the reduction temperature. A two- stage process can be applied to waste gases that contain excessive quantities of oxygen, nitrogen oxides, and water vapor. The best sorbent for the first stage appears to be a nonalkali or nonalkaline earth medium since this medium more readily releases the SO2 for reduction in the second stage.

Jan 1, 1973

By Oliver Bowles

The National Granite Commission at its annual meeting in Norfolk, Va., in January, 1930, passed a resolution requesting the Bureau of Mines to conduct an economic study of the granite industry. In compliance with this request a preliminary review has been made of trends, in, the production and uses of block granite. Some unfavorable conditions, were, thus brought to light and certain suggestions regarding a. more orderly and consistent growth in the industry are herein discussed. The results of the study axe, presented in this report for the earnest consideration of the industry and comments are invited, not only on this report but as to future work that might be accomplished by the Bureau of Mines. The authors desire to acknowledge many helpful suggestions and comments from Paul M. Tyler of the Bureau of twines and from Harris F. Sherman, secretary of the National Building Granite Quarries Association. Miss A. T. Coons of the Bureau of Mines rendered valuable, assistance through her wide knowledge of granite statistics.

Jan 1, 1931

By William Catron

This paper is one of a series being prepared by the United States Bureau of Mines on mining methods, practices, and cuts in the various reining districts of the United States. The mining methods described are those used in the mines of the Cananea Consolidated Copper Co., a Mexico corporation whose holding company in the United States is the Greene Cananea Copper Co. The mines are at Cananea, Sonora, Mexico, 25 miles directly south of the international boundary, approximately in 31° nor to latitude and 110 to 130° west longitude. Cananea is connected with the boundary towns of Naco and Nogales, Ariz., by a standard-gage railroad.

Jan 1, 1930

By Laurence F. Kelley

This paper is one of a series being prepared by the United States Bureau of Mines on shaft-sinking methods and costs at individual operations in various mining districts of the United States. The methods and costs described herein are those of The Consolidation Coal Co. at one of its operations in the Tug River district, McDowell County, W. Va. ACKNOWLEDGMENT The author is indebted to Frank R. Lyon, vice-president, Thos. G. Fear, general manager of operations, and Chas. Enzian, chief engineer, of The Consolidation Coal Co., for valuable assistance and collaboration in the preparation of this paper. W. A. Cole, manager of the E. J. Longyear Development Co. furnished valuable data on methods and performance averages.

Jan 1, 1932

By W. E. Bruce, James Paone

Drillability or a measure of drilling performance has been based on ( 1 ) hardness and toughness of rocks , ( 2 ) power input to the drill compared with total volume of hole , and ( 3 ) penetration related to resistive forces of rock on the applied penetrative forces . An analysis of some representative previous work is made . Experimental drillability curves from AX- size diamond core bit performance in eight different rocks ranging from dense hard taconite to soft limestones are presented . Results show that in small bore diamond drilling , compressive strength and possibly other rock properties may be a useful parameter in predicting drilling rates .

Jan 1, 1963

By J. D. Ramsdell

The object of this investigation by the Federal Bureau of Mines was to evaluate the workability, recrystallization characteristics, and mechanical and physical properties of high-purity electrorefined vanadium. The low level of interstitially soluble elements in electrorefined vanadium results in a soft ductile metal which responds readily to cold working by rolling, swaging, and press-forging. Hardness, strength, and resistivity increased with an increase in impurity content, but thermal expansion was independent of impurity content. The work-hardening of vanadium occurs rapidly. Most of the hardness increase occurs in the first 15 pct. of reduction in area. When vanadium is annealed, its hardness increases to a maximum when the annealing temperature is between 200° to 400° C. A sharp decrease in hardness develops as the annealing temperature is increased. An anomaly in the hardness versus annealing temperature curve is present in the 600° to 800° C. range, while all evidence of cold-work is removed at annealing temperatures above 900° C.

Jan 1, 1961

By K. K. Kelley

Synthetic fluorphlogopite mica (KMg3AlSi3010F2) is a relatively new product developed at the Norris (Tenn.) Station of the Bureau of Mines, Thermodynamic data have applications both in the production and use of this product, and the work described in this paper was undertaken to fill the need for such data. Measurements were made of the heat of formation at 298° K., the heat capacity between 50° and 298° K., the entropy at 298° K., and the heat-content and entropy increments between 298° K. and a maximum of 1,804° K. These basic data are combined to obtain heats and free energies of formation of the mica from the elements and from molecular constituents at temperatures ranging from 298° to 1,800° K. Minimum heat requirements to form melted mica from commonly used ingredients were calculated.

Jan 1, 1959

By Clarence Karr

In 1955 the Federal Bureau of Mines established a low-temperature tar laboratory at its new Appalachian Experiment Station in Morgantown, W. Va. The objective of the laboratory is to investigate the yields and chemical and physical properties of tars from low-temperature carbonization of coal, to investigate means of economically upgrading these tars, and to make available to industry and the public essential data for increasing coal utilization through the establishment of a new coal-chemical industry, based on the utilization of low-temperature tars. Because of the obvious economic significance of phenols, as well as the relative ease with which they can be separated and analyzed, initial research has centered mainly around this class of tar constituents. It was realized early that no listing of phenols and their physical properties existed that included enough compounds to be practicable. The purpose of this paper is to make such a compilation available.

Jan 1, 1957

By J. J. Forbes

Since 1910 the Bureau of Mines has given training in the care and use of oxygen breathing apparatus under conditions that may exist during mine fires and after mine explosions. In 1929 the Bureau supplemented this instruction by initiating a course in advanced mine rescue training to prepare mine officials and others to organize men for mine rescue and recovery operations. The course of instruction has been developed and expanded since its inception to keep abreast with new ideas, methods, and equipment. Four miners' circulars were issued to be used in the training course. The first of this series (Miners' Circular 33) deals with mine gases and the various methods of detecting them; the second (Miners' Circular 34) gives instructions for sampling and analyzing mine atmospheres; the third (this circular) describes methods and equipment for protection against mine gases; and the fourth (Miners' Circular 36) explains procedures in sealing and unsealing mine fires and in conducting recovery operations, These circulars have been revised from time to time to keep them up to date.

Jan 1, 1954

By C. W. Smith

The U.S. Bureau of Mines; Tuscaloosa Research Center, in cooperation with the U.S. Army Corps of Engineers under interagency Agreement No. 14-09-0078-1510, conducted a comprehensive sampling program of 10 upland disposal sites along the Alabama, Black Warrior, and Tombigbee River systems in Alabama. Samples from each site were characterized according to particle size, chemical analysis, mineralogical content, and potential end use. Additionally, samples were subjected to the Toxic Characteristic Leachate Procedure to determine the presence of potentially harmful heavy metals. Based on the results of these studies, each sample was determined to have properties amenable for use as aggregate in general-purpose portland cement concretes and certain asphalt concrete applications.

Jan 1, 2010

This publication contains four papers presented at a seminar on mine subsidence control held in Pittsburgh, PA, on September 19, 1985. The seminar was designed to keep the mineral industry informed of new technology developed by the Bureau of Mines that permits reliable and accurate prediction of mine subsidence. The papers describe actual field studies undertaken by the Bureau to monitor surface subsidence over longwall panels. Topics discussed include the efects of subsidence on water table levels, the development of subsidence pre calculation methodology suitable for use with the specific lithological conditions of the Pittsburgh coalbed, an engineering comparison of technologies used in surveying for longwall mine subsidence, and a comparison of the process of subsidence over two different longwall panels.

Jan 1, 1985