Search Documents

By Wesley G. Holtz

A project to demonstrate the feasibility of retorting oil shale by the Paraho vertical retort process was carried out at Anvil Points, Colorado during 1974 to 1976. As a part of the demonstration project, laboratory and field tests were performed to determine the physical and chemical properties of the retorted shale for use in the development of eventual full-scale disposal plans. The material which exits from the Paraho retort is classified as a non-plastic silty gravel by the Unified Soil Classification System. The particles have an apparent specific gravity averaging near 2.60 and a mass specific gravity averaging near 2.00. The material can be compacted by normal laboratory and field construction methods to about 90 to 100 pounds per cubic foot dry density depending upon the degree of compactive effort applied. The addition of moisture does not improve compactibility appreciably. When high compactive effort is applied the retorted shale is classed as impervious to water flow. The compacted retorted shale exhibits shear strengths in the same order as those observed for silty gravel soils. If the compacted material is cured (long tune simulation testing) prior to strength testing considerable strength gain can be obtained from cementing action. The amount of cementing developed is dependent upon heat treatment and other operating modes of the retort.

Jan 1, 1976

By John J. Henn

An evaluation is presented of the Bureau of Mines process for the recovery of metal and mineral values from municipal incinerator residues. This process employs standard mineral beneficiation techniques and is operating on a pilot-plant scale of 1,000 pounds of incinerator residue feed per hour. Products from this separation process include ferrous, aluminum, and copper-zinc scrap, and colorless and colored glass. Cost estimates were prepared for four plant sizes. The estimated capital and operating costs For the four plants follow: [ ] It is assumed that the separation plant is located adjacent to a municipal incinerator. Provision is made, however, for part of the residue feed to be delivered by truck so that one large separation plant can be used for residue from more than one incinerator.

Jan 1, 1971

By O. H. Metzger

This is the first of two papers dealing with construction and use of aerial tramways in the metal-mining industry. It describes practices and equipment used in tramway construction and discusses the design of tramways. The second paper will describe the construction and operation of tramways and give operating costs. ACKNOWLEDGMENTS The author acknowledges the cooperation of a number of cable and tramway manufacturers Who supplied practical manufacturing data and other valuable information. Full credit for formulas used in the design of aerial tramways it given' to Edward B. Durham3/ and F. C. Carstarphen.4/

Jan 1, 1937

By Douglas F. Scott

In 1981 the U.S. Bureau of Mines and U.S. Geological Survey conducted a mineral survey of the Pyramid RARE II area (No. 5023) covering 23,500 acres (9,500 ha) of E1 Dorado National Forest and 7,900 acres (3,200 ha) of the Lake Tahoe Basin Management Unit (fig. 1). The Bureau of Mines investigation did not reveal mineral deposits in the area. Samples taken from silicified and limonite-stained metasedimentary rocks and aplite dikes were void of precious or base metals or uranium. Placer samples from stream gravels contained no gold values. Molybdenite occurs in quartz stringers within quartz monzonite near Grass Lake, adjacent to the area; no extension; were found in the area.

Jan 1, 1982

[ ]

Jan 1, 1981

To develop effective noise controls for continuous min-ing machines (CMMs) to reduce worker noise exposure. Background Noise-induced hearing loss (NIHL) is an occupational illness caused by chronic exposure to excessive sound levels. For underground coal mine workers, NIHL continues to be a serious health issue. Analysis of hearing loss data suggests that by retirement age, 70%?90% of U.S. coal mine workers will have a hearing impairment. Operated in the confined spaces of underground mines, large industrial mining equipment often produces sound levels that can be harmful to workers. Of all equipment used in underground coal mining operations, CMMs account for the most noise overexposures. To reduce the occurrence of noise over-exposures, engineering noise controls must be developed for the CMM.

Sep 1, 2008

By W. W. Adams

[Sales of explosives - permissible explosives5/ other high explosives, and black blasting powder - in the United States during the calendar year 1937 reached a combined total that slightly exceeded the quantity sold in 1936. A larger output was reported for permissible and other high explosives but a smaller for black powder. Production of the three classes of explosives totaled 404,744,294 pounds, more than 3 percent over 1336. The total quantity produced included 49,579,441 pounds of permissible, 288,924,253 pounds of other high ex- plosives, 36,403,950 pounds of black powder in pellet form, and 23,836,550 pounds of black powder in granular form. Sales of granular black powder declined 26 percent compared with 1936 and of pellet black powder 12 percent; gales of permissible explosives increased nearly 4 percent and of other high explosives 10 percent]

Jan 1, 1938

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in Saline and Pulaski Counties, Ark., has been given in Report of Investigations 4251. The factual data obtained during the project are reported in a series of Reports of Investigation beginning with No. 4251, of which this is the fourteenth. The data are accompanied by maps showing the location of holes drilled and the deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned & name and a number for ready reference and identification, and its location and name are shown on the appropriate half-township map. The description of each half township is followed by a description of each deposit developed in that half township. The 14 half-township maps and 77 detail maps of the bauxite deposits in this series of reports give the locations and numbers of all the holes drilled except the deep holes drilled to test geophysical anomalies. The locations of those holes are shown on figure 13 in volume 1. The descriptions of the deposits developed are followed by complete detailed logs of the drill holes. Many of the widely spaced exploratory holes did not discover bauxite of minable thickness and grade. The pertinent information obtained from the widely spaced exploratory drill holes has been summarized and tabulated, and a table for each half township is given with the discussion covering that area.

Jan 1, 1948

By Arnold O. Tanner

The domestic mining industry gained more strength in 1988 as the healthy comeback that became evident in 1987 continued and grew for many commodities. The increasing and more stable commodity prices, still predominantly in the metals sector, reinforced both the new ways of conducting business and the use of technological advancements in successfully lowering operating costs during the last 4 to 6 years. Some commodities and companies still struggled to survive, but increases in productivity and profits were becoming more common.

Jan 1, 1990

By J. A. Eisele

The Bureau of Mines conducted bench-scale cyclic tests to determine the composition of recycled leach liquor in the Bureau?s proposed clay/HCl leach/ HCl sparge process for producing Al203 from clay. The data developed from these tests make it possible to synthesize leach liquors for predetermined steady-state operating conditions when conducting large-scale crystallization tests. The results of two sparge tests were compared. One was a 20-cycle test with a 36-pct-HCl concentration in the mother liquor; the other was a 10-cycle test with a 26-pct-HCl concentration in the mother liquor. The effect of impurity concentrations in the leach liquor on the purity of aluminum chloride (AlCl30?6H20) crystals was determined, but there was poor correlation between this data and results that have been obtained from miniplant-scale work.

Jan 1, 1980

The original work statement of this contract was entitles: 'A Accident Analysis Model for Use in Underground Coal Mines.' The contract was scheduled for a duration of 26 months and was to be in three phases: Phase I - Model Development, Phase II - Application of the Model, and Phase III - Installation, Monitoring and Evaluation of the Model. Alter three months in Phase I, it became apparent that much of the needed data for the model was nut available and could not be made available within the original study schedule. Proceeding as plumed would have resulted in a model of limited utility. Personnel from Theodore Barry and Associates and the Bureau discussed the problem in detail and mutually decided to utilize the majority of remaining funds to assist the Bureau in solving these data problems and develop a stronger ongoing capability for safety analysis within the Bureau. Both tie contractor and the bureau officials involved believed that this decision greatly enhanced the Bureau's ability to develop future accident prediction models, whose rigor would greatly exceed what was currently possible.

Jan 1, 1972

By C. W. Smith

The U.S. Bureau of Mines conducted research to determine the effect of ground water control on the dewatering of phosphatic clay wastes. Two storage impoundments were constructed. One impoundment was surrounded on three sides with a series of well points (shallow vertical wells) to lower the ambient water table and the second impoundment served as a control. Ground water was pumped from the area surrounding the test impoundment for a period of 490 days. A constant pumping rate of 60 gal/min resulted in a water table drawdown of 13 ft, approximating the bottom of the impoundment. At the end of the test period percent solids in the test impoundment was 35 pct, while in the control impoundment percent solids was only 26.8 pct. Percent solids of greater than 30 pct is required for capping and final reclamation using fertile overburden.

Jan 1, 1989

By David D. Hottinger

Only a minimum amount of illumination is generally provided for many types of mobile surface mining equipment. This condition presents a hazard to operating personnel working on and around such equipment. To reduce this hazard MSHA has proposed safety regulations requiring minimum levels of illumination for hazardous zones on and in the immediate area surrounding surface mining equipment. This report describes a Bureau of Mines sponsored project demonstrating the feasibility and effectiveness of providing dragline illumination in compliance with the proposed MSHA regulations. A description of the computer aided design, on site installation and field evaluation of individual lighting systems for each of three different size draglines is presented

Jan 1, 1981

By A. J. Kraemer

For a number of years the Bureau of Mines has been conducting an investigation of crude petroleum from producing fields in the United States and the Western Hemisphere and has published a series of reports on these fields. Analyses of crude-oil samples tom some oil fields of Louisiana are given in Bulletin 291.4/ Analyses of 26 representative crude oils from various producing formations of southern Louisiana are given in is report. These.samples are from 14 field's in 10 parishes in the southern part of the State, usually designated as the "Louisiana Gulf Coast area." ACKNOWLEDGMENTS Thanks are due the representatives of the various companies from whom samples were obtained for their cooperation and assistance in helping to secure representative samples. The samples were analyzed under the direction of E. C. Lane at the Bartlesville station of the Bureau of Mines.

Jan 1, 1934

By R. A. Egen

The purpose of this book is to provide an indication of what good hoisting practice is and how it might be achieved. To this end the book contains discussions of equipment and inspection and maintenance procedures developed and used by mining people in striving for safe, reliable hoisting equipment. Most of this information comes from domestic practice; the rest is foreign, notably from Canada. Most things discussed have long proved their general worth, and others promise to; a few are beginnings. However, nothing is conjectural or theoretical; the practices described herein are in use somewhere in the mining world. The stress is on equipment in use; it is not a design-guidelines manual. Nevertheless, there are some sections dealing with design material since it may be of value in a maintenance/ replacement sense. Mine hoisting installations encompass such a wide variety of equipment and conditions that it is impractical to specifically cover them all. This book mainly treats conventional systems using conventional components with some discussion of the more common unconventional (special) systems in use. There is no recognized definition for a "conventional" mine-hoisting system. Herein the term means those systems most commonly used in daily operations for transporting men, materials, and product-electrically driven drum and friction hoists, with guided conveyances running in vertical or inclined shafts. Beyond this, what "conventional" means is probably best illustrated by the topics discussed.

Jan 1, 1975

By C. A. Herbert

The mine of the Alpha Portland Cement ..Co., Iroaton, Ohio, ..working in. a. bed of limestone 96 feet thick at a depth of approximately 510 feet below the surface, has established a won¬ derful safety record, having operated 6 years—frcra September 21, 1926,. to September 21, 1932 - without a lost-time accident. This mine, with 61 to 86 employees (average 68) and daily output of 1,000 to 1,200 tons of limestone, operated 1,041 days during the 6-year period, or the equivalent of 578,894 man-hours of exposure. ...... ... . Immediately above the limestone is a 20-foot .bed of hard..sandstone.. At present about 10 feet of limestone is left up as. a roof and.about. 42 feet is being extracted. Of the lower portion of the bed it is believed that about. 25 feet. ..immediately below . the .present workings is suitable for cement and will be extracted later. The mine workings are reached by two rectangular concrete shafts, one a 2-compartment hoisting shaft and the other a 2-compartment air and escape shaft- In the latter shaft one compartment is used as an airway and the other, as a cage compartment fo.r a man and material cage. .. . - . The tipples at both the air shaft: and. hoisting shaft are-of steel. The.ground landings at both shafts are fenced in with hand-operated gates in front of the cage compartments.- The two shafts and the crushing plant, which .is.a part of the hoisting shaft-tipple structure, are adjacent to the mill buildings. The rock is hoisted on self-dumping cages in 4 ton capacity, end-gate, steel cars. An electric hoist with automatic overwind device is used at both the main shaft and air shaft. The controls for the main hoist are in the tipple where the engineman is stationed and from which point he has an unobstructed view of both the ground, landing and the cage coming into the dump.

Jan 1, 1933

By Howard B. Hamilton

A switching system for high fault current 300 and 600 volt DC trolley and haulage systems, as used in the mining industry is presented. The system consists of paralleled main and auxiliary contactor circuits with a liquid metal current limiting device (CLD) in series with the auxiliary contact-or. Upon detection of a fault, the current is commutated into the CLD circuit. The liquid-metal vaporizes, increasing the CLD resistance and Considerably decreasing the actual current to be interrupted. This system will materially reduce the wear and tear on contactors because of the reduced interrupting requirement. the CLD is pressurized; when the current is interrupted, liquid metal flows back into the bore. Thus, it is resetting. Electrical and mechanical design principles are presented as well as materials for use, as found satisfactory in field tests on the device.

Jan 1, 1982

Information Circular (IC) 9453 Roof falls continue to be the greatest single safety hazard faced by underground coal miners. During1996-99, 44 coal miners lost their lives in rock falls and nearly 2,400 were injured. In addition, nearly 6,000 non injury roof collapses were reported. Roof supports are installed to protect the miners, but support system failures contributed to most of these incidents. Reducing the terrible toll taken by ground falls continues to be a major goal of research by the National Institute for Occupational Safety and Health (NIOSH).During 2000-01, NIOSH conducted a series of open industry briefings on New Technology for Coal Mine Roof Support in Norton, VA, Charleston, WV, Evansville, IN, Tuscaloosa, AL, Price, UT, Glenwood Springs, CO, and Washington, PA. Drawing on many years of research undertaken by the NIOSH Pittsburgh and Spokane Research Laboratories, the proceedings describe what types of coal mine roof support are available, how they work, and when they should be used. The major subjects covered include roof bolts, standing roof supports, cable supports, and longwall shields. Some special topics are also addressed, including an analysis of roof fall accident statistics, techniques for better skin control, and material handling considerations. The proceedings volume also contains information on several important new technologies, which are described for the first time, e.g., guidelines for selecting roof bolt

Aug 1, 2001

By L. R. Burdick, J. F. Barkley

"There is a general conceit in the coal trade that the moisture- and ash-free B.t.u. of coal from the same seam, and surely from the same mine,is substantially a constant; that calculation of the moisture- and ash-free B.t.u. value from the proximate analysis and B.t.u. determined in the laboratory will reveal whether a coal came from a given area or seam; and that, having this constant, the B.t.u. value of a coal sample can be calculated fairly closely upon a dry or as-received basis from the moisture and ash values of its proximate analysis.To illustrate with a simple example;"

Jun 1, 1941

By Ronald M. Van Noy

A reconnaissance study of kyanite-group mineral deposits in the Northwest has revealed large exploitable reserves of the mullite-forming raw materials in the Woodrat Mountain and Goat Mountain districts of north-central Idaho. Potential coproducts or byproducts are garnet and muscovite mica. The Woodrat Mountain district contains garnet-kyanite-mica schist, which has been traced for 6 miles and may extend farther. Surface samples average 29 percent kyanite and contain up to 15 percent garnet. Inferred reserves of strippable ore with a low waste-to-ore ratio, and containing more than 15 percent kyanite, are more than 3 billion short tons. The Goat Mountain district contains several kyanite-mineral zones. Samples of the richest zones average from 10 to 20 percent kyanite minerals and represent about 200 million short tons of strippable rock. Beneficiation tests indicate that the kyanite minerals and garnet can be concentrated by a combination of gravity, flotation, and electromagnetic methods. Reserves in these deposits are sufficient to satisfy any foreseeable domestic and export demand. However, the freight tariff to reach the nearest major users of kyanite (located in the Midwest) has discouraged development of western kyanite resources. Western demand of a magnitude to support a moderate to large milling operation has not yet been developed. However, there is some foreign market potential. If a garnet byproduct could be prepared and sold for coated abrasive products or as grinding grains, an offset possibly could be gained to a por¬tion of the mining and milling costs for the Pacific Northwest producer. Such byproduct values would offer a means for expanding the geographic market areas as well as the regional market potential.

Jan 1, 1970