Search Documents

By D. C. Fleck

Electrorefining yttrium from selected low-melting yttrium--base alloys is investigated, and various halide systems are studied as potential electrolytes for use in preparing low-oxygen yttrium by electrorefining unalloyed yttrium. Yttrium cathode products having significantly less metallic impurities than the anode materials were prepared from alloys containing nickel, iron, and manganese by electrorefining in LiCl-YC13 electrolytes at 900° to 1,000° C. Yttrium-copper and yttrium-magnesium alloys are not suitable as anode feed materials, An evaluation of chloride, fluoride, bromide, and mixed chloride-fluoride electrolytes showed that cathode products containing much less oxygen than the anode material can be obtained in the fluoride and mixed chloride-fluoride systems. Initial cathode current density has no apparent effect on the purity of the products obtained in both phases of the investigation.

Jan 1, 1973

By LaMar G. Evans

The rapid determination of uranium in ores by radiometric means was investigated by the Bureau of Mines. Among the various procedures and schemes tested, two showed most promise. They were the ratio scheme developed in the Bureau's Tucson, Ariz., laboratory and the equilibrium method developed by the Canadian Department of Mines and Technical Surveys. The ratio method is a simple, empirical procedure for classifying the state of equilibrium in ores by measuring their radioactivity by means of a Geiger-Muller counter under three different conditions, using filters. The principal merit of the method is in providing a clue as to the reliability of equivalent uranium determinations.

Jan 1, 1958

By Jay C. Hanson

Various electrical and electromagnetic (EM) geophysical techniques are currently being evaluated by the U.S. Bureau of Mines for their effectiveness in the detection and monitoring of electrically conductive (1 to 5 S/m) lixiviant (leach solution) to depths of 600 m, either above or below the water table. These techniques include magnetotellurics (MT) , controlled source audiofrequency magnetotellurics (CSAMT), resistivity and focused resistivity, ground-penetrating radar (GPR), frequency-domain electromagnetics (FEM), and time-domain electromagnetics (TEM). Of these techniques, TEM may be the most effective, but CSAMT and focused resistivity also hold promise. Geophysical computer modeling of the borehole TEM technique was conducted based on an idealized geoelectric section (layered earth) with characteristics based on the Santa Cruz porphyry copper deposit near Cas a Grande, AZ. Layer resistivities and thicknesses were obtained from geophysical data and geologic logs available from the site. Modeling of borehole TEM in both preleach and during leach situations was conducted. Simulating the TEM method using computer modeling proved to be encouraging since there were substantial differences between leached and nonleached responses. The modeling does not prove the effectiveness of TEM in the field, but does indicate that detection of deep lixiviant zones is theoretically possible.

Jan 1, 1992

By R. J. Leary

The technologies of contemporary iron and steel production and of direct reduction processes have been studied to identify and estimate the potential effects of direct reduction on mineral consumption and the problems raised thereby for the Nation's mineral supply to the iron and steel industry. Contemporary patterns of mineral raw material and energy consumption were determined from a study of the 1964-70 period. Major changes were observed in requirements for 14 of 20 principal commodities. Average practice in 1970 was compared to best practice to estimate the potential effects of implementing existing technology without recourse to direct reduction. Potential effects of direct reduction were estimated by comparing the mineral requirements for 95 percent reduced pellets with 1970 best practice technology for two cases of use: (I) complete substitution for hematite pellets in blast furnace burdens, and (11) partial substitution (40 percent) for scrap in electric furnace steel charges. Effects upon mineral supplies are described; important collateral factors are analyzed, and the principal metallurgical, industrial, and environmental consequences of implementing direct reduction are discussed. Major effects of direct reduction on the domestic steel industry and its mineral supply system are foreseeable. Direct reduction will (1) create a large demand for low-gangue iron ore; (2) relieve the dependence of the steel industry on coking coal, and (3) permit great increases in furnace productivity, both in blast furnace ironmaking and electric arc furnace steelmaking.

Jan 1, 1973

By Richard L. Rains

In 1992, the Bureau of Mines evaluated mineral resources of the 34,043-hectare Caribou City and 41,943-hectare Stump Creek study areas in southeastern Idaho. No resources were delineated. The areas had been proposed for wilderness. Rocks underlying the study area are part of the Idaho-Wyoming Thrust Belt. At Caribou Mountain they have been intruded by diorite-monzodiorite. Where the intrusive rocks contact calcareous members of the thrust belt, skarn bodies have formed that host metal deposits. Gold, both placer and lode, occurs in the Caribou City area, and salt occurs in the Stump Creek area. Production records show 73.5 kg (2,363 ounces) of placer gold were produced; however, field studies indicate more than 2,000 kg (67,000 ounces) probably were recovered. Minor amounts of lode gold, silver, and copper were recovered from the hard rock mines. Production of salt from the Stump Creek study area in the 1860's was used by emigrants on the Oregon trail and also shipped to various mining districts for use in silver recovery. Oil and gas were drilled for, but all holes are plugged and abandoned. There are no current leases. Examined workings consisted of 25 adits, 3 shafts, 50 prospect pits, and extensive placer workings all in the northern tip of the Caribou City area, Current BLM records show 168 placer and 146 lode claims; 14 claims are patented.

Jan 1, 1993

By R. G. Gürtunca

Over the past century coal miner safety and health has seen tremendous improvements, the fatality and injury rates continue to decrease while productivity continues to increase. Many of the hazards that plagued miners in the past, such as coal bumps, methane and coal dust explosions, ground fall accidents and health issues have been significantly reduced. The contribution of NIOSH research includes products for prevention and survival of mine fires, methane control measures, design procedure for underground coal mines, methods for excavation surface controls, methods and procedures for blasting, laser usage in underground mines and prevention of electrocution from overhead power lines that have reduced accidents and injuries in underground coal mines. Health research has produced products such as the personal dust monitor, noise abating technologies and ergonomic solutions for equipment operators. Research priorities at NIOSH are set by considering surveillance statistics, stakeholder inputs and loss control principles. Future research in coal mining is directed towards respiratory diseases, noise induced hearing loss, repetitive musculoskeletal injuries, traumatic injuries, falls of ground and mine disasters. The recent spate of accidents in coal mines resulted in the Miner Act of 2006 which includes a specific role for NIOSH in future mine safety research and development. The mine safety achievements in the USA reflect the commitment of industry, labour, government and research organizations to improving the safety of the mine worker.

By Joseph M. Singer

This research project had two main objectives: (1) To identify the smoke limits of gaseous fuel-air mixtures and (2) to obtain and evaluate basic chemical information on the formation of smoke in very rich flames near the smoke limit. Such information would do much to establish the circumstances for car-bon deposition in gas appliances and in other types of combustors. Based on tests with ethylene and propane, these studies showed the following: 1. Smoke limits are related to the yellow-tip limits of the fuel. Previous research established sufficient data to permit prediction of yellow-tip limits on gas burners using a wide variety of fuels. The present study of smoke limits deals only with ethylene-air flames, but the concept that was developed is probably applicable to other fuels.

Jan 1, 1962

By W. D. Bensema

Two different techniques were used to make measurements of the absolute value of electromagnetic noise in an operating coal mine, Itmann No. 3 Mine, located near Mullens, West Virginia. The electromagnetic environment created by 250-volt-dc and 550-and 950-volt-ac machinery in two longwall panels was measured and is reported. One technique measures noise over the entire electromagnetic spectrum of interest for brief time periods. It is recorded using broadband analog magnetic tape, and the noise data is later transformed to give spectral plots. The other technique records noise amplitudes at several discrete frequencies for a sufficient amount of time to provide amplitude probability distributions. The specific, measured results are given in a number of spectral plots and amplitude probability distribution plots.

Jan 1, 1974

By Richard J. Mainiero

The Bureau of Mines conducted research to evaluate the optimum design for a rock-breaking explosive charge that could be fired unconfined in a gassy or dusty coal mine without the danger of igniting the flammable atmosphere. Charges of various shapes, with and without cavities, were tested in a gallery using 3-by 3-by l-ft concrete blocks as simulated boulders. For these tests the optimum charge, in terms of cost, weight, and convenience in handling, consisted of a flat l-1/2-lb charge of permissible explosive seven-eighths of an inch thick and 7 in in diameter encased in a l/2-in thick layer of fine salt (NaCI). This work demonstrated that it should be possible to produce an inexpensive explosive rock-breaker charge that would be safe to use in underground coal mines.

Jan 1, 1982

By Aleksandar D. Bugarski, Robert J. Timko

Despite extensive research efforts conducted in the past decades, occupational health risks associated with exposure to nano and ultrafine aerosols emitted by diesel power equipment are still not completely understood. The complexity of physical and chemical properties of diesel aerosols, constantly changing with the implementation of advanced diesel emissions control technologies, make this task rather challenging. The objective of this paper is to identify and characterize nanometer and ultrafine aerosols emitted by diesel engines in the underground environment and evaluate the effects of selected contemporary control technologies on physical properties, chemical composition, and in-vitro toxicology of diesel aerosols. The physical and chemical properties of the nanometer and ultrafine diesel aerosols are to be characterized through a test series in the NIOSH Lake Lynn Laboratory experimental mine. The crucial part of the study has been development of a facility that allows researchers to generate field results with precision and accuracy characteristics of a laboratory environment. The knowledge obtained from this study should strengthen our understanding of the health implications related to exposure to diesel particulate matter and aid in assessing the potential of various control technologies for reducing this exposure.

By M. G. Zabetakis

This publication contains highlights of a 4-hour lecture and demonstration by the Bureau of Mines on the fire and explosion hazards of flammable liquids and solids, oxidizing materials, corrosive liquids, and compressed gases. The authors first presented this material as part of a 2-week course given to officers and enlisted men at the U.S. Coast Guard's Dangerous-Cargo Handling School, established at Fort Eustis, Va., in 1959. The Bureau was asked to present the lecture and demonstration because of the extensive experience of its researchers in handling certain harardous commodities.

Jan 1, 1961

By Donald R. Alvic

For electric utilities serving the aluminum smelter industry in the United States, sulfur oxide (SOx) abatement legislation could bring about increases in the costs of generating electricity. This paper documents the method and assumptions used in estimating these increases, and the contains the results of the estimation. 1.2 SMELTER INFORMATION The smelters used in this study were identified by the Bureau of Mines (BOM) and are listed in Table 1.1. Also included in Table 1.1 are the electric utilities that serve these smelters. Compliance costs were estimated for these utilities. Some of the utilities are unique in the way that the information is handled or in the way the utility is operated; these are discussed below. 1.2.1 Big Rivers and Associated Co-ops, Data for Big Rivers and Associated Co-ops were gathered by George Mason University (GMU) students for BON and are included in this study.

Jan 1, 1988

As part of the Bureau of Mines program for conserving domestic mineral resources, a survey was made of the methods used for identifying scrap metals. Because of the large number of alloys currently being scrapped, correct identification of these materials is essential if they are to be recycled effectively. The methods and instruments used to identify scrap metals are described and evaluated. These include object recognition, color, density, magnetic testing, spark testing, chemical spot testing, thermoelectric measurements, eddy current measurements, and elemental analysis by chemical and instrumental methods. Other potential techniques are discussed also.

Jan 1, 1982

This manual provides instructions for installing, operating, and maintaining a protective canopy on the Galis Mfg. Co. face drill. The instructions are based upon an actual installation made in the mine on face drill model 460-S. The parts list and engineering drawings for the protective canopy are included at the end of the manual. And a discussion of some alternative design concepts is also included. The manual can also be used for retrofitting other face drills with similar protective canopies. Skilled mechanics can determine if the instructions herein would be applicable to the other face drills and can determine any necessary modifications if they are not.

Jan 1, 1973

By G. L. Oldright

The studies previously made on Smelting in the Lead Blast Furnace have dealt with the custom smelter of the International Smelting Co. at Tooele, Utah,4 and on the smelter of the Bunker Hill & Sullivan Mining & Smelting Co.5 at Kellogg, Idaho. The International plant may be considered representative of the traditional custom smelter. The lead smelter of the future seemingly will have to treat increasingly richer lead charges. This feature was then stressed in describing the Bunker Hill plant.

Jan 1, 1934

By Stephen H. E. Phillips

This report outlines the modifications that have been carried out to the original prototype rectangular shaft sinking equipment for its use in a circular shaft. The surface testing of the machine is described where seven, 24 ft. diameter shafts were excavated to an average depth of 21 ft. at rates ranging between 1 ft/hr and 1.9 ft/hr depending upon the prevailing conditions. The durability and productivity standards for the equipment were established indicating that the objectives of the project had been realized. That is, when using the machine the sinking rates could be increased by 25% and costs reduced by a corresponding amount compared with conventional drill and blast methods. In addition it was shown that the machine had been developed to a state of fitness for sustained underground use.

Jan 1, 1981

By Joseph W. Horne

This report presents the results of an investigation by the U. S. Bureau of Mines in cooperation with the State of Colorado, on the yields and properties of oils produced from oil shale, lignite and subbituminous coal using the standard assay method developed by the Bureau for oil-shale testing,. The purpose of this work, which is part of the general study of oil shales being conducted by the Bureau of Mines and cooperating agencies, was to obtain information on the amount and character of the yield of crude oil or tar from different typical oil shales, the yield of light oil or naptha that might be suitable for use in motor fuels, and other products of shale oil. As the west has large resources both of oil shale and low-grade non-coking coals, it is of interest to know the relative yields of tars, light oils, and combustible gases that can be produced from these coals when retorted under conditions similar to those suited for oil-shale retorting. Source of Samples The coal samples were obtained from deposits on or adjacent to the public lands in the States of the Rocky Mountain region. Many of the mines sampled are operating under Government leases or permits. The number of coal samples secured from the various states are: Colorado, 6; Montana, 9; north Dakota, 6; New Mexico. 1; South Dakota, 1; Wyoming, 9. Of these samples, 14 were lignite coal, 16 subbituminous coal, and a bituminous coal. The standard channel method of the Bureau of Mines was used for sampling. Coal samples received at the Boulder Office weighed about twelve pounds each, and duplicate samples were sent to the Pittsburgh Station for proximate and ultimate analyses. The origin of the samples and description of the deposits are given in Table 1.

Jan 1, 1927

By D. J. Parker

On Thursday, March 18, 1937, the country was shocked by news of a terrific explosion at the New London, Tex., school, which caused the death of 280 pupils avid 14 teachers. The explosion occurred at about 3:05 p.m. in the largest of the 11 school buildings on the campus. Fire 1 shows this building, marked "Main high school building", with respect to other buildings, pipe lines, oil wells, and gas lines or the property.

Jan 1, 1937

By W. L. Falke

The Bureau of Mines has developed a system that permits the "soft" soldering of aluminum and aluminum alloys with standard tin-lead solders. The method employs application of a thin nickel-copper-alloy coating to the substrate, which enables the tin-lead solders to wet readily and spread over the areas to be joined. With conventional technology, aluminum and aluminum alloys are extremely difficult to solder because tenacious surface oxide films prevent wetting. With the Bureau-developed method, the aluminum substrate is mechanically or chemically cleaned to facilitate bonding to a minute layer of zinc that is subsequently applied with an electroless zincate solution. The nickel-copper-alloy (30 to 70 pct Ni) coating is then applied electrolytically over the zinc, using immersion cell or brush-coating techniques. Development of acetate electrolytes has permitted deposition of the proper alloy coatings. The coated areas can then be readily joined with conventional tin-lead solders and fluxes. The joints so formed are ductile, strong, and relatively corrosion resistant, and exhibit strengths equivalent to those formed on copper and brass when the same solders and fluxes are used. The method has also been employed to soft-solder magnesium alloys.

Jan 1, 1983

By Zsuzsanna Zborovszky

Study of different parameters (minimum discharge voltage, minimum discharge current, wire electrode diameter, speed of separation, electrode materials, overlap of the electrodes, etc.), their direct effect on the power going into the discharge, and their indirect effect on the possibility of obtaining ignition with an 8.31% methane-air mixture from a resistive circuit. Critical evaluation of the Cadmium disc breakflash (the presently internationally recommended test apparatus). Description of experimental setup and apparatus.

Jan 1, 1974