Search Documents

By John Platt, Mark Stephens

"When blasting is required in critical areas and anticipated shot movement and quick cleanup areessential to the success of the project it is extremely important to use the best technology available to achieve the goals expected by the customer. Wampum Hardware was given such a challenge in 2014-2015 when the PA Turnpike and New Enterprise Stone and Lime hired the company to do presplit blasting along the PA Turnpike. The face height averaged 45 feet (13.72m) and the shots had to be controlled to stop within 60-75 feet (18.29-22.86m) of the face or in this situation before they entered the travel lanes on the PA turnpike. In many if not most blasting environments, it is essential in controlling the movement of a blast, to make certain that the face holes are drilled at exactly the right place, with the proper amount and type of burden in front of and to the sides of the borehole. Profiling is an important first step to insure that the holes are drilled at exactly the right place and showing us the correct amount of burden in front of each and every drill hole."

Jan 1, 2016

By Travis Davidsavor, David Provost

A segment of high-pressure steel petroleum pipeline needed to be replaced on a hillside and beneath a waterway within an existing right-of-way containing multiple petroleum pipelines. The pipeline replacement required excavation of sedimentary rock to allow placement of the new pipe. As a result of an existing right-of-way limitation, steep slopes, and hard rock, blasting would be required as close as 7.8 meters (25 feet) from two operating pipelines. Existing pipeline company standards would have effectively precluded the construction of the replacement pipe by blasting rock. To facilitate the required construction and evaluate actual pipe stress during blasting to ensure pipeline integrity, a comprehensive evaluation methodology was developed by a team of pipeline, mechanical, geotechnical, instrumentation, and blasting engineers. A total of 60 strain gages were affixed to the steel pipe and seismographs were buried at the surface near the blasting area. Test blasting allowed pipe stresses with corresponding ground motion to be monitored. A conservative analysis approach evaluated individual peak strains and revealed that only small pipeline strains, and therefore stresses, were induced in the pipeline as a result of blasting. This evaluation allowed specific procedures to be developed to inform the blasting operation of maximum explosive loading and minimum charge distances. Additionally, this effort provided the pipeline operator with appropriate pipeline operating pressures during blasting activities to limit total stresses in the pipeline to be below allowable stresses imposed by code, regulators, and company operational limitations. Recommendations were developed to measure the blast generated ground vibrations with seismographs buried at the depth of the pipe, near the pipe, and limit the ground vibrations from blasting to 150 mm/s (6 in/s). If ground vibration intensities of 120 mm/s (4 in/s) or more were observed, additional engineering review is recommended. Finally, all blasting would be suspended and all activities reviewed at peak ground vibration intensities of 230 mm/s (9 in/s). The evaluation effort resulted in effective and efficient construction of the pipeline replacement and allowed the pipeline operator to better understand blasting induced stresses on their assets.

By Harsh Kumar Verma

Blasting off-the-solid is the most commonly used method during development of galleries in Bord and Pillar method of underground coal mining. In this method, only P5 explosives are used with permitted delay detonators in accordance with the safety requirements stipulated by the regulatory bodies. Delay detonators made with pyrotechnic delay compositions have inherent scattering in their delay timings. It is desirable to use precise detonators to achieve better fragmentation, less vibration and noise. Overlapping of delay period is undesirable from production as well as safety point of view.

Jan 1, 2008

By Kevin Phelps, Jason Baird, Philip Mulligan, Dominique Nolan

Determining the transitions from run-up to optimal cut length and optimal cut length to run down, without bias, from the penetration of a linear shaped charge (LSC) is difficult. The stresses applied to the targets during explosive testing can distort the targets in such a manner that determining the true distance of cut, penetration, or fracture can be demanding. Through the course of this research, it was observed that the researchers made many of the errors involved in the collection of data. Among these errors researchers found problems in: determining and fitting the sample to a single plane from which to read measurements, determining where along the path of cut the three phases of penetration transition, and the precision of measurement based on handheld tools and the human eye. This study looks at three methods of recording the data of a series of linear shaped charge tests. The tests resulted in samples which are not ideal for measuring with common laboratory devices like measuring tapes, calipers, or rulers. The first method utilized these common laboratory devices and the difficulties the authors experienced are described in this paper. The second and third methods involve digital photography, image manipulation, and the use of AutoCAD. Methods two and three are then compared to the simple observational method and discussion is made in regards to the precision and accuracy of each method.

Jan 1, 2013

By TTE-Europe GmbH

A few years ago, the term Track & Trace for explosives was only known in Europe and Brazil at most; the introduction of this technology is experiencing an undreamt-of boom worldwide. More and more countries are enacting legislation to introduce Track & Trace of explosives and follow Europe and Brazil on this path. At present, the world's leading manufacturers are already using such solutions, are in the process of implementing them, or are in the planning process. However, based on the experience gained in Europe, there are outstanding challenges for all manufacturers. These are questions of compliance, logistics, distribution, and, of course, especially, the necessary adaptation of the production environment. However, this development involves considerable effort on the part of the manufacturers. New devices for marking the explosives and digitally recording the data are integrated into the production process. This should be done as cost-effectively as possible, without restricting production capacity and speed, and with as few process changes as possible. This paper uses real-life customer experiences examples to explain paths from project design to real implementation. Lessons learned from the experience of European explosives manufacturers are presented, missteps are described, and solutions are identified. Individual steps along this path are explained, and solutions are told to avoid pitfalls and bottlenecks. Finally, it refers to the risk analysis and concrete examples in implementing the planning into production. Methods of marking various explosives are shown, and the use of Track & Trace to solve logistics tasks in picking and shipping explosives, including the data exchange with ERP (Enterprise Resource Planning) systems.

Jan 26, 2026

By Laurent Airaud

For around ten years, electronic detonators are available for those who want to use advanced methods and to apply theories promoted by engineers and professors to reduce blast concerns or improve fragmentation and dilution. Furthermore, decision makers can verify the use of electronic detonators to drive down mining costs. Engineers and more specifically blasters are the actual users and have to be convinced of the easiness of electronic detonators. This paper deals with electronic detonators and the notion of easiness. Common feelings about the notion of easiness are discussed. Then, examples of new technologies like, automobile, photography or Information Technology are discussed to observe how they progressed throughout time with new features and sales volume. For the specific explosive initiation industry, each step of the life of an electronic detonator is dealt with concerning the easiness and a table is used to quantify this notion.

Jan 1, 2004

By H. Wallin, I. G. Wallace, J. Akhavan, E. Nilsson

Over the past three years the UK together with Sweden, Norway, Finland, Italy have been taking part in a EU funded Leonardo da Vinci programme. More recently EFEE have participated in the project known as the EU15/10/200715/10/2007Excert project which is aimed at addressing the perceived loss of explosives expertise in several EU nations. This could have implications for explosives safety and industrial competitiveness. The paper outlines the work that has so far been done in phase 1 and describes the work planned for the second phase of the project. The paper will describe work in the UK to develop competencies for all explosives workers in both the civil and defence sectors. These competencies in the form of National Occupational Standards have now been approved in the UK and are accompanied by a range of 24 new National Vocational Qualifications launched in May 2006. The paper will show how the standards define knowledge and skills and how these form the basis for vocational qualifications as well as higher education awards and professional qualifications. This UK initiative is now being considered in other EU countries and the project has now been extended to also include Germany, France, Portugal, Czech Republic, Lithuania and Estonia. To support the occupational standards and qualifications work is also being carried out to improve learning provision in the explosives area. In addition to formal educational and conventional training courses a series of workplace learning initiatives are being pursued as well as internet learning packages. Examples of these initiatives will be given.

Jan 1, 2008

By Mattos J. L. C

Drilling and blasting with explosives in mining operations near communities require careful planning to mitigate socio-environmental impacts. Ground vibration, noise emission, flyrock, and dust dispersion are factors that may trigger conflicts with local populations. However, large-scale operations demand high productivity and intense material handling, making it essential to balance operational performance with impact control. The adoption of best practices, combined with advanced monitoring and mitigation technologies, enables sustainable mining even in proximity to inhabited areas. This study proposes the use of double and triple-deck blasting techniques with large-diameter boreholes (12 ¼” – 311 mm), addressing the sizing of charges and decks, as well as measures aimed at reducing noise perceived by nearby communities. The approach seeks to maintain the use of large drilling rigs already present in the operation, avoiding costs related to premature equipment replacement or expensive alternatives, while minimizing environmental and social impacts and promoting a more balanced and responsible mining model.

Jan 26, 2026

By Ankit Jha, RICHARD AMOAKO

In this paper, we examine the challenges associated with the use of empirical rock fragmentation models. We highlight key parameters omitted by these models, and propose a machine learning approach that incorporates these parameters, leading to a simple, yet more accurate approach to blast design.

Feb 1, 2020

By John Tatom, Michelle Crull, Robert Conway

The US Department of Defense Explosives Safety Board is sponsoring the development of a risk-based explosives safety siting program, SAFER. The fragment and debris hazard generated at the potential explosion site (PES) is critical at an exposed site (ES) over a significant range of standoff distances. The Science Panel Impact Debris Evaluation and Review (SPIDER) test program has been planned to develop improved predictions for the hazards inside an ES by fragments and debris. Data will include the mass and velocity required for perforation of the test cross-section and the characteristics of all debris produced inside the ES.

Jan 1, 2010

By D. Rudenko, C. T. Aimone-Martin, J. K. Ratliff, I. G. Wong, J. Aiken, R. E. Burnham, T. A. Davidsavor

A small quarry blast was conducted with a maximum of 90 pounds per delay and shortly afterwards, area residents sensed ground motion and building shaking indicative of an earthquake. In addition, seismometers up to 500 miles (800 km) away recorded a magnitude 2.8 earthquake located in the area. Positioned in a seismically inactive area, southern Minnesota is not known for earthquakes. The earthquake was originally described by the USGS to be a surface blast at the quarry. Analysis showed that the earthquake occurred shortly (approximately seven seconds) after the quarry blast some distance away and well below the surface. This paper describes the evaluation of the “seismic events” including the blast, the following earthquake, initial governmental response, and provides the framework for assessing the relationship between the blast and the earthquake. The paper also discusses management of large volume claims from a complex event and presents a claims management strategy with best practices.

Feb 6, 2023

By Norman Paley, Finn Ouchterlony

Detailed fragmentation data for different blast delay timing tests at the Red Dog mine in Alaska are analyzed. This work is a continuation of previous work in which the crusher output was found to be better described by the three-parameter Swebrec function than by the Rosin-Rammler function. For a crusher model, the x50 variable sufficed to describe changing crusher input while b and xmax could be considered fixed. For the crusher output from aggregated stockpile rock, as measured by digital image analysis using Split-Online, the constancy of b was not as apparent. In this paper detailed stockpile data, single Split data series, and sieved belt cuts of crusher product are analyzed using the Swebrec and truncated Rosin-Rammler functions. The variability of b is confirmed. By using specific fraction passing sizes a shortcut is presented that removes the need to do curve fitting to determine the three Swebrec function parameters.

Jan 1, 2013

By William Hissem

When we look out on our business landscape today, the words higher, faster, fdwther come to mind. Compliance issues, business integration, increasing production and profitability demands are converging in an age old industry and giving it a new twist. Not that the rock changes, rather that as the variables of our business change, the resulting “cut-off grade in business” turns ore into rock or rock into ore. The trick is to emphasize the latter. As with the miners of yore, what was recovered from the business enterprise had a lot to do with tools and skill. So it is today. When the casual observer looks at drilling and blasting operations today, many see the same basic offering in terms of equipment types and process. Looks, however, can be deceiving. As with the aviation sector, a given machine might took similar to previous generations of equipment, but in fact is radically different in terms of power, efficiency, accuracy, and range. So it is with hydraulic top-hammer drills today.

Jan 1, 2000

By A T. Spathis

Corrections are given for “A three parameter rock fragmentation distribution” by A.T. Spathis (Measurement and Analysis of Blast Fragmentation, Workshop hosted by 10th International Symposium on Rock Fragmentation by Blasting, New Delhi, India, November 25-29, 2012 pp. 73-86). Typographical errors in two equations for the uniformity index in the two versions of the original and modified Kuz-Ram model are corrected. It is noted that the modified equation in the original published paper of Cunningham also had the same typographical error. A corrected plot of the dependence of the uniformity index versus the burden to diameter ratio is given. These corrections do not affect the rest of the original published paper.

Jan 1, 2013

By Joseph A. Meyers

NYC has always been a high-profile target for both foreign and domestic terrorists. Explosives have always been the go-to tool for terrorists to bring about serious physical injury, death, and property damage in our society. Today with the anti-police movement gaining traction in the United States and anarchists groups using homemade explosives against law enforcement and municipalities, it is the responsibility of the explosives industry to ensure that every explosive product on a blasting site is secure. We must prevent the theft of these energetic materials used on projects and sold by vendors so they are not used by these terrorists. We have learned many lessons here in NYC which began with the theft of explosives used for blasting projects in NYC to supply the IRA (Irish Republican Army) 50 years ago. The liability is too significant to take short cuts in securing energetic materials. Over the years through cooperation with all agencies and the industry we in NYC have developed certain proven protocol and procedures we would like to share with the industry. An efficient and effective security plan for the logistic movement of explosives, as well as for the blast site is imperative to keeping the good name of the industry from negative repercussions and possible additional bureaucratic oversight of an industry that is highly regulated and still recovering from the pandemic. Communication, security assessments and transparency with all stakeholders and the Authority Having Jurisdiction (AHJ) will greatly improve the overall security for the blasting project. This SOP (standard operating procedure) will allow the AHJ to become a proactive partner in the security of the blasting project. If the AHJ is not a law enforcement agency, the law enforcement agency specialty unit must be notified and included in all phases of the project. The security for a blasting project with AHJ and law enforcement input starts at the inception of the project when the memorandum of understanding (MOU) is obtained, and involves the AHJ through all steps of the approval process. This includes threat assessments on new and existing structures. SME’s (Subject Matter Experts) must be present at all stages. The blasting industry and regulators must work collaboratively to improve safety, security, and create a dialogue with law enforcement and the AHJ. Relationships are built through trust, teamwork, transparency, and communication and greatly improve the safety of our great country.

Jan 21, 2025

By Jose Luis Pineda Villarreal

New technologies emerge every day with practical applications for open pit mining. For every operation, managers need to understand the best way to increase efficiency in drilling, blasting, fragmentation and hauling routes.

Jan 1, 2018

By Guo Ziqing, Tang Qiuming, Liu Yuanyuan

The channel-type non-mechanical stirring production process is a new developed technology for emulsion explosives in recent years. It removes traditional equipment such as mechanical-mixing emulsification, mechanical-mixing sensitization, matrix pumping, and explosive pumping, and has been applied in China. This technique achieves a fusion of higher intrinsic safety and lower cost, as well as the excellent quality of products and high efficiency of production. The emulsion particle diameter is about 0.5μm. The storage period of emulsion explosive produced with span-80 emulsifier is more than 7 months.

Jan 21, 2025

By Rachel E. Gooding, George C. Emmett, David R. Bradley

The United States (U.S.) Department of Homeland Security (DHS) Directorate of Science and Technology (S&T) is using a probabilistic risk assessment (PRA) approach to evaluate the risks from terrorist use of explosive materials against the Homeland. A similar approach is currently being used to evaluate the risk from terrorist use of chemical, biological, radiological and nuclear materials.

Jan 1, 2017

By Sami Kara, Yunseok Park, Seung-Joong Lee, Namsun Hwang, Michael Laing

This study conducts a comparative analysis of construction efficiency. In the first part we compared electronic and non-electric initiation systems, focusing on tunnel contour holes. Field blasting operations were executed across a variety of delays to identify the optimal delay time. This delay for the in-situ rock mass was determined through regression analysis of blasting vibration in contour holes and for overbreak/underbreak. The blasting results with the electronic initiation system using the obtained optimal delay, applied to contour holes, were compared with the results of the non-electric initiation system. The overbreak and underbreak decreased by an average of 2.7 cm and 5.8 cm respectively, by using the electronic initiation system. Moreover, the vibration reduction rate in contour holes region was reduced by 11.9% based on the blasting vibration estimation equation proposed by the Ministry of Land, Infrastructure, and Transport (MOLIT). Underground construction projects have become increasing popular as cities grow in both size and density. This growth severely limits the amount of useable space for new project on the surface, resulting in the decision to build them underground. This new policy however brings into focus the challenge of managing and reducing blasting related vibration due to the proximity of these projects to sensitive structures, utilities and foundations often present in urban environments. For this purpose, we have been required to manage the vibration by reducing the quantity of explosives used per round. Inspired by surface blasting techniques, we applied a decking mode to address and work around this challenge. We present in this paper the first attempt to blast a tunnel face using a decking method and reduce the charging per hole from 6 kg to 3 kg per hole and keep the same advance rate for this tunnel. The results are presented in the third part of this paper. In the second part we present the results of the decking mode in shaft. The use of the electronic initiation system in tunnel construction provides the users an effective tool to improve the overbreak/underbreak and keep the vibration at a low level with a large gain on the overall project schedule and budget. This what we want to demonstrate in this paper.

Jan 21, 2025

By Rob Farnfield, Mark Pegden

Old Cliffe Hill quarry produces between 4 and 5 million tonnes of crushed granite per year and is located in the county of Leicestershire in the East Midlands region of England. Blasting is carried out with bulk emulsion explosives in combination with either shock-tube or electronic detonators.

Jan 1, 2010