Search Documents

By R R. Singh, U K. Dey, S K. Roy

"Commercial explosives being a heterogeneous mixture of many chemical compounds in prefixed proportion, their velocity of detonation (VOD) may vary from batch to batch, due to variations in the proportion of the chemical composition and process parameters even within their tolerance limits. Inherent limitations of measuring methods and human variations during measurement also add to the variation in VOD values determined practically. Therefore, it is customary to define a range of VOD values rather than a fixed value of VOD for a particular explosive.Variations in VOD values of four commercial permitted explosives in India were evaluated under open unconfined condition using Dautriche method and a resistance wire method based continuous VOD meter. Comparative evaluation of VOD values of selected explosives were aimed to check the relative effectiveness of continuous VOD measurement of small diameter cartridged permitted explosives using cheaper co-axial wire instead of recommended costly VOD rods along with the continuous VOD meter. Results of evaluation revealed that continuous VOD of commercial small diameter cartridged explosives could be determined using cheaper co-axial resistance cable with comparatively better accuracy than the most commonly used Dautriche method."

Jan 1, 2007

By Alejandro Rosario, Ricardo González

The restrictions imposed by the Brazilian environmental legislation regarding natural caves lead to a block of substantial amount of mineral reserves. Mining activities can released caves, as long as the company ensures that the activities will not cause any damage to them, requiring profound and time-consuming studies. Since the use of explosives in the mine are potential sources of some damage to any structures, it leads to a deep need for controlling the rock blasting activities. In this context, the maximum charge per delay used in operations close to cave regions must follow some internal blasting assumptions that have been developed during specific tests and mining activities. By the seed wave technique, it is possible to determine the behavior of a seismic wave, which travels through a rock mass and it is generated by blasting a known explosive charge. This technique has proved to be an effective tool because it is able to accurately include the physical characteristics of the rock and different lithologies. This paper discusses about modelling blasting induced vibrations in order to improve caves protection, which surround the mining operations.

Jan 1, 2019

By Mark A. Rugen

It may be difficult to imagine but small engineering companies do exist, even in relatively large cities like San Antonio. Due to the limited capital available for the purchase or use of equipment such as computers, many times the small company must evaluate a blast damage claim by limited means. This paper will discuss how a relatively small company has managed to become the leading blast damage experts in an area without the use of computers or sophisticated equipment. It will be shown that a single individual in a company who is familiar with vibration theory, local soil conditions and who does not mind spending long hours with a calculator and reference books can satisfy both the insuranc e adjuster or attorney, and the homeowner concerning the claim. Several examples will be given which show the typical flow of work and the ultimate outcome. This paper will focus on the special problems encountered by a small firm and how these can be overcome, and the unique interaction of a small engineering firm with both the insurance adjuster/attorney and the homowner that can lead to an equitable settlement of the claim.

Jan 1, 1983

By P D. Katsabanis, S Kim

A number of small scale fragmentation tests have been conducted to analyze the effects of blasting effort on the grindability of granite, granodiorite, limestone and iron ore. Powder factors were modified, post-blast fragments were screened and drop weight tests were conducted on fragments of different sizes to deliver a variety of specific impact energies. The fragmentation from the drop weight tests has been analyzed to examine the effect of impact energy and powder factor on size reduction. A consistent effect of blasting on the various fractions of the fragmentation distribution has been obtained for all rocks used. The effect of powder factor on the impact fracturing of the rocks has been expressed in a convenient relationship between progeny size, impact energy and powder factor used in obtaining the primary fragmentation. It is clear that explosives consumption affects downstream size reduction; depending on the rock, the effect can be substantial at coarser final sizes but very small in the case of grinding to small final sizes. Differences from the expected trend can be attributed to changes in blast design. As an example, the effect of in-hole collision of detonation waves is analyzed.

Jan 1, 2011

By Joe Atalla, Leojenen Etulle, Jesse Desrochers, Joseph Mukendi Kabuya, Remi Proulx, Ruilin Yang

The Mont-Wright mine is Canada's largest open-pit iron ore mine with multiple open pits in operation. It is operated by ArcelorMittal Mining Canada in the northeast of the province of Quebec, near the town of Fermont. Fragmentation of rocks with explosives generates vibrations and gas expansion that damage intact rocks, affect existing crack networks, reduce the shear strength of discontinuities and the quality of the rock mass of the highwalls. The efficiency of its blasting operations is challenged by the need to optimize production and manage the risk of mine slope instability caused by vibrations from successive blasts. This paper presents a Multiple Seed Waveform (MSW) vibration model that was established at the mine for this purpose. Near-field signature hole blast vibration monitoring was conducted in multiple areas to establish site characterization as input to the blast vibration modeling at the highwalls of the site. The vibration attenuation laws were established and the effects of different blasthole diameters, shifting frequencies and presplit design were evaluated. Based on the results obtained from the near-field blast vibration monitoring, the calibrated MSW vibration model was used to select blast design parameters to control blast vibration while maximizing productivity of blasts at Mont-Wright mine.

Jan 26, 2026

By Yonghun Jong, Chungin Lee

The main purpose of this study was to apply the artificial neural network (ANN) models to determine optimal powder factors and predict peak particle velocities, based on a series of observations and input parameters. The used blasthole pattern was V-cut. The locations of blastholes and ignition patterns remained almost constant. The input parameters were 14 geological conditions (i.e., dip, dip direction, spacing, separation, and persistence of 2 discontinuity sets, tunnel orientation, rock strength, RQD, and RMR) and 4 blasting conditions (i.e., distance between blasting points and measuring points, charge weight per delay, drilling length, and blasting efficiency). Data for the ANN application in this study were recently collected in a highway tunnel under construction in Korea. The main rock type in the site was biotitic granite. An optimum ANN model was determined by training models with collected data. The trained model was used to evaluate the prediction capability of the optimum model. It was shown that the ANN model could predict the powder factor and the peak particle velocity depended upon the selected input parameters. Particularly, the ANN model predicted more accurate peak particle velocities than those obtained by the blasting vibration equation. Moreover, the more dominant factors among the input parameters could be determined by analysis of the relative strength effect.

Jan 1, 2002

By Miguel Araos

The aim of this study was to understand clearly how VOD of emulsion-based gassed explosives is influenced by parameters such as nitrate salt composition in the oxidizing phase, product density, blend composition, gassing rate, type of sensitization, etc. Also some VOD testing was performed on watergel-based gassed explosives in order to compare the results with those obtained for emulsions. VOD measurements were conducted in the surface blasting facility at the Research and Development laboratory of ENAEX SA (Calama, Chile). Despite the fact that the influences of some parameters on VOD of emulsion-based gassed explosives are easily predicted, there was found to be an unexpected correlation. Although it is commonly believed that the VOD of gassed explosives depends on the density, this study found that the VOD depends on the both size and the amount of gas bubbles incorporated into the product as well as type of sensitisation, regardless of whether the explosive was straight emulsion or a blend. Density is just a consequence of the incorporation of voids into the explosive. Future work in this area may examine variation of other parameters, in order to obtain a greater knowledge of detonation properties and therefore to design more efficient explosives.

Jan 1, 2002

By Mario Karfakis, G. Langlois

Well stimulation is the process by which any production well, whether for production (extraction), storage (injection) or deep interaction (remediation, monitoring, etc) can be made or stimulated to flow at higher levels. This stimulation is driven by active methods to increase the permeability in the near-well environment and create a larger zone of communication between a well and the reservoir it services. Well stimulation is a crucial aspect of well completion and reservoir engineering and is a subject of careful pre-drilling planning. In many modern industrial endeavors the effectiveness of well stimulation is often critical to economic viability. Because of the broad impact of well engineering on several large industries (petroleum and natural gas extraction and storage, geothermal power, groundwater monitoring, extraction and management, environmental remediation, mining and minerals extraction, etc.) changes in the state of the art in well engineering and well stimulation can affect the capabilities of very diverse and disparate industries. This paper is an effort to communicate the status and effectiveness of current practice and technology in well stimulation. The intention being that effective communication of progress can spur innovation in industries that require well stimulation but are removed from immediate communication of technological or practical improvement.

Jan 1, 2009

By Andrew Ritter, Victor I. Montenyohl, Stephen R. Winzer

Thirty-seven open pit production blasting operations have been monitored using high-speed cameras running between 500 and 7000 frames per second. Analysis of the resulting films reveals irregularities in timing including sequencing errors and crowding (holes firing less than 8 ms apart), confirming results of laboratory testing of ms delay blasting caps (Winzer, 1978). Where blasting parameters are otherwise constant and within recommended guidelines (stemming, spacing, burden, etc.), timing problems dominate the overall performance of the blasting operation. Model tests in layered Homalite 100, designed to simulate joint or bedding planes in rock, indicate the importance of the stress waves generated by the explosive in developing the crack network which is ultimately responsible for the fragmentation seen in the resulting muckpile. These mechanisms are strongly supported by high-speed film studies at Pinesburg, Maryland. Experiments in controlling relief in deep shots (where depth approaches the lateral extent of the bench blasted) using borehole geometry and hybrid initiation systems (electronic timer and pyrotechnic delays) were carried out. The results suggest that the 1 me/ft. of burden guideline developed by Bergmann et aI., 1974 is too short, and that much longer times are necessary to optimize fragmentation and muck digability. Longer times are found to reduce noise, vibration, and flyrock.

Jan 1, 1979

By Ralph E. Burnham, J. Kelly Ratliff

"The words “dynamite,” “TNT,” “explosives,” and “blasting” typically cause the general public, andjurors, apprehension and fear. Although blasting operations conducted by well-trained, skilled, andexperienced blasters rarely cause damage or injury, the public’s perception of blasting is that it isdangerous, disruptive, and results in damage to nearby properties. As a result, blasting operations have always resulted in complaints, claims, and lawsuits. However, in recent years, the public perception combined with an increase in public opposition, social media, more stringent regulations, predatory plaintiffs’ attorneys, and the application of strict liability to blasting claims has resulted in an increased threat of litigation to blasting companies and individual blasters. Consequently, many blasting companies find themselves receiving more complaints, involved in more litigation, and facing an alarming number of frivolous claims, which can result in increased insurance costs and other financial tolls. Accordingly, today’s blasting companies must be prepared for litigation and take steps to eliminate accidents and claims before the first shot is detonated on a job. The best way to accomplish this is standard operating procedures that incorporate best management practices, industry standards, and regulations in daily operations. This paper outlines some of the considerations that a blasting company should incorporate into its standard operating procedures before, during, and after the shot."

Jan 1, 2016

By Ashlin Pillay, Osamu Iwata

Hong Kong is ranked as the world’s third most important international financial hub and attracts significant growth and development annually. The city is also known as the world's most vertical city, the most common view from your window in Hong Kong city centre is probably the window of another 30 storey skyscraper. The increasing demand for real estate in this bustling Metropolis has placed immense pressures on its transportation infrastructure because whilst the construction continuously grows upward with larger and larger skyscrapers, it leaves the transportation planners with very little choice but to go underground. As a first world city, interrupting daily business operations is simply not an option; however, of even greater concern is the safety of these 8 million residents. Blasting Regulations are under the strict control of the Mines Division showing zero tolerance to the breaching of safety standards. The Ho Man Tin Station (HOM) excavation, a part of the Kwun Tong Line Extension (KTE) project situated in Hong Kong began in June 2012 and is one such project that is under strict regulations from the Mines Division. The HOM project is a cross cut interchange station between the Kwun Tong Line Extension (KTE) and Shatin Central Link (SCL).

Jan 1, 2015

By Rakesh Raghavaraju, Bibhu Mohanty

Prediction of fracture and fragmentation characteristics of a rock mass subjected to dynamic loads, such as in blasting remains a major technical challenge. The present study is aimed at characterizing the shock transmission properties in controlled experiments in small scale in a well-characterized granitic rock, under varying borehole coupling conditions. Single blast-hole tests were conducted in a granitic rock sample of 145 mm (5.7 inches) diameter and height. The boreholes (in two diameters: 6.4 mm (1/4 inch) or 9.5 mm (3/8 inch)) were loaded with detonating cord of varying charge weight (5.3 g/m or 25 grains/ft to 31.8 g/m or 150 grains/ft of PETN). The effect of explosion gas penetration into the target rock was eliminated by inserting a thin-walled copper liner along the borehole wall. Embedded carbon composite resisters were employed at varying distances from the borehole to measure transmitted shock pressure for two coupling conditions (i.e. air and water) at distances of 1x to 9x the borehole diameter. The paper analyzes the decay of shock pressure as a function of distance from the borehole, and its implication on shock-induced fracture properties of the target rock as the first step in predicting fracture and fragmentation behaviour in a well-characterized rock.

By Christodoulos Xiouris, Ali Reza, James Karnesky

A rocket parachute signal flare is often used to signal a maritime emergency. In the general operation of these devices, a solid rocket motor propels a metal body to an altitude of approximately 1000 ft(305m).At the end of the rocket motor, a propelling charge drives a signal flare and parachute out of the metal body and ignites the flare, which then burns for approximately 40 seconds as it falls to earth. In this paper, we describe an engineering investigation of an accidental ignition of a rocket parachute signal flare, which caused injury to the user. The components of the flare involved in the accident were inspected via x-ray and microscopic imaging techniques, and compared with those of unfired flares recovered from the same vessel. Chemical analysis of residue on recovered components from the accident flare was also performed. These comparisons were used to determine the likelihood that the actuation mechanism had been deliberately manipulated. In the subject model of the flare, ignition of the rocket motor is accomplished through a percussion cap which is struck by a firing pin. Prior to activation, the firing pin holds down a pre-compressed spring. We present a comparison of the ignition system of the incident flare with those of other rocket parachute flares, which do not incorporate any stored mechanical energy.

By W. Birch

The traditional concept of scaled-distance modelling for predicting blast induced ground vibration holds many drawbacks, not least of which is the major effect data scatter imparts on confidence determination. An investigation by the Department of Mining and Mineral Engineering, The University of Leeds, England has resulted in the development of simple but effective method of improving prediction capacity through the reduction of effective error by incorporating individual location response into a scaled-distance model. The work is the product of an l&month blast-monitoring campaign at a limestone quarry situated in North Yorkshire, England. The data, when presented in the form of a scaled-distance model, indicates a typical scenario where a good overall correlation becomes marred by the extent of data scatter. Examination of the individual monitoring locations however indicates that the response of the individual location is an important factor in the explanation of the large residuals. The novel approach thathas been developed incorporates a series of locational site factors which when incorporated into a scaled distance model reduces the effective error and therefore improves prediction capacity. The approach is based on using a standard computer package “spread sheet” on the understanding that these are commonly available on all quarry or home computers. This approach has been validated by comparison with a more rigorous statistics method.

Jan 1, 2001

By Mark S. Stagg, David E. Siskind

The Bureau of Mines arranged to have a wood-frame test house built in the pat of an advancing surface coal nine so it could investigate the effects of repeated blasting on a residential house. Structural fatigue and damage were assessed over a 2-yr period. The house was subjected to vibrations from 587 production blasts with particle velocities that varied from 0.10 to 6.94 in/s. Later, the entire house was mechanically shaken to produce fatigue cracking. Failure strain characteristics of construction materials were evaluated as a basis for comparing strains induced by blasting and shaker loading to those induced by weather and household activities. Cosmetic or hairline cracks 0.01 to 0.10 mm wide occurred during construction of the house and also during periods when no blasts were detonated. The formation of cosmetic cracks increased from 0.3 to 1.0 cracks per week when ground motions exceeded 1.0 in/s. Human activity and changes in temperature and humidity caused strains in walls that were equivalent to those produced by ground motions up to 1.2 in/s. When the entire structure was mechanically shaken, the first wallboard tape joint crack appeared after 56,000 cycles, the equivalent of 28 yr of shaking by blast-generated ground motions of 0.5 in/s twice a day.

Jan 1, 1985

By B Mohanty

Full-face blasting rounds have been used to excavate a 4.6-mdiameter shaft at Atomic Energy of Canada Limited's Underground Research Laboratory near Pinawa, Manitoba. Both standard pyrotechnic delay detonators and the newly developed electronic delay detonators (EDD) were used on the project. The full-face blasting technique, employing 89-mm-diameter relief holes and 38-mm diameter blast holes, NG-based explosives, and the regular long period delay detonators, has been standard practice at the site, giving excellent wall control and fragmentation results. The comparison blasts using pyrotechnic detonators and EDDs were carried out to test the operational logistics, timing accuracy and blast results obtained with the latter. The long period pyrotechnic delays ranged from O to 18, with the nominal delay varying between 350 ms and 800 ms. The EDD blasts used the same number of periods, with the respective delay interval between successive periods set precisely at 190 ms and 210 ms for the two blasts. Based on a broad range of critically assessed parameters, the EDD blast results proved to be signficantly superior to those obtained with regular pyrotechnic detonators. The results have been analyzed in detail and the relative merits of the two delay systems have been determined. Alternative designs to derive maximum benefits from EDDs in shaft and tunnel blasts have also been suggested.

Jan 1, 1990

By L. L. Oriard

he Metropolitan Water District of Southern California (MWD) supplies water to some 16 million people in a semi-arid region. Most of this water is imported. Some of the supply lines cross over the San Andreas fault, one of the most notorious and active faults in the U.S. There was a serious need for emergency water in case normal supplies should be interrupted. To fill that need, MWD had to find a reservoir site on the west side of the San Andreas fault, west of the mountains. Because of the distinctive nature of the location, it was necessary to construct a huge “bath tub” by building a dam at each end of a valley, requiring some 115 million cubic yards (88 million cu.m) of fill. In effect, two large-scale surface mining operations have been under way simultaneously. The $2.2 billion project is known as the Eastside Reservoir Project. Because of space limitations, this paper will be limited to those topics which are expected to be of primary interest to explosives engineers, principally related to large-scale rock fill production. There is not sufficient space to discuss the many diverse geotechnical questions related to site selection, geological and geophysical field testing, laboratory testing and design considerations. This brief overview may assist those who might be interested in making a tour of the project site following the ISEE conference.

Jan 1, 2000

By W. Jiao, Y. Yongqi, R. Shan

Soft rock mines are distributed through out P.R.C. And drilling and blasting is still the main method of driving a tunnel in these mines. Traditional smooth blasting has been widely and deeply studied and put into practice in P.C.R since 1970s. But the cartridge and blast hole are both columns, the stress field in the rock around blast hole at the beginning is symmetry around hole axis, and the original cracks in the rock can be activated randomly. So serious overbreak and underbreak at the boundary of an excavation occur often, especially when the excavation is in soft rockmass, and the rates of half-hole marks are generally about 50% in medium rock, and 20-30% in soft rock in Chinese coal mines. For the sake of overcoming the situation, we have been studying directed crack blasting since ten years, and have got some obvious achievements in this respect. Slotted cartridge control blasting in soft rock is studied in this paper. Through model experiments, reasonable decouple coefficient range and slot width are gotten, and unsymmetrical dynamic strain field is analyzed. Through underground test in soft rock with a strength lower than 1OMpa in Dayan Mining Bureau, The results of which the rates of half-hole marks and the nonsmooth grades of the cut contours are 83.3% and 1OOmm respectively have been achieved.

Jan 1, 2000

By William Adamson

Precise and data driven methods of predicting and modelling blast induced vibration intensity are created and applied under field conditions on a routine basis today. These models are fed with controlled field measurements of vibration pulses generated by controlled charges under known geometric conditions. With such models blasting and geomechanical engineers can estimate vibration intensity at established critical points in mine bench geometry (surface mining) as well as within semi-permanent crown and rib pillars (in underground mining).Damage to bench walls and destabilization of large-scale geomechanical structures can be partially attributed to high intensity blast induced stresses on the rock mass and structures that define important features such as safety catch berms and haul roads. In the underground environment, weakening of critical pillars in block caving or Long Hole Open Stoping(LHOS) operations may lead to ore sterilisation. Blast vibration intensity can be linked with physical alteration in critical rock mass volumes within themine. Often the potential for vibration damage is estimated by the calculation of a critical value of vibration intensity, derived from a consideration of laboratory measured rock matrix properties. Efforts to confirm the accuracy of these estimates of critical vibration level include post blast excavation photography as well as the visual examination of rock mass, pre-and post-blast, using video camera observation of the walls of purpose drilled observation holes. These methods clearly indicate a change in fracture state due to the blast induced vibration, however further modelling of geomechanical stability will benefit if seismic measurement data can be interpreted in terms of geomechanically relevant strength parameters. This paper describes some of the results of previously unpublished research studies conducted in underground operations in Chile and Australia, where cross-hole seismic measurement profiles were interpreted in terms of dynamic modulus. This work dates from a period between 1987 and 1990 and the Author suggests that 30 years on, applying modern day technology, instrumentation and modelling methods, more meaningful, practical and applicable results may be obtained.

By J. Rafael Otaíza, Francisco Mardones

This work has addressed the problem of creating a predictive model of the maximum particle velocities in the rock mass (PPV). The model designed specifically can model the subsequent vibrations of blasting based on geometric parameters, explosive loading, and the blasting process itself. Models based on artificial intelligence (AI) algorithms can find useful non-linear patterns to solve classification, regression, clustering, among other problems. They are flexible mathematical transformations adaptable to various objectives and types of data. With their different levels of abstraction, they can find a function that relates the input variables to the sought-after response. These models have been successfully used in similar contexts (Prashanth, (2018)) and have achieved state-of-the-art results in the field (Lawal, (2021)). The main challenge is to adapt them to the context of Chilean mines, in addition to including the geometric information of the blasting and the heuristic to obtain the set of optimal parameters, it is proposed to follow the work of (Simonyan, (2013)) and obtain "saliency maps" adapting it to tabular variables. We implemented an Artificial Neural Network (ANN) with a large number of neurons in the hidden layers. Models based on neural networks can find useful non-linear patterns to solve classification, regression, clustering, among other problems. They are flexible mathematical transformations adaptable to various objectives and types of data. With their different levels of abstraction, they can find a function that relates the input variables to the sought-after response. The literature shows that, for the problem of rock type identification, basic neural networks perform well (Simonyan, (2013)), but lack uncertainty estimates. This is a data-driven model, and in this sense, the model training was carried out using data from multiple operations in the large copper mining industry in Chile. In these databases, data consistency and the balance of the various independent variables that have the greatest impact on the model were ensured. With the above, the optimal hyperparameters of the model were determined, obtaining a predictive R-squared of 0.94.

Jan 21, 2025