Search Documents

By Cristian Castro, Patricio Gomez, Jason Furtney, Augusto Lucarelli

Understanding the effect of blast-induced damage on wall stability is critical to safe and economical operation of a large open pit mine. In this paper, a numerical modeling methodology is used to investigate damage to rock at distances of greater than 10 m (30 ft) from a blast. Two applications of the model are demonstrated. First, the method is applied at a zinc mine to investigate the effects of pit blasting on underground stopes. The model predictions are compared with the scaled distance formula. Next, the model is used to investigate a common problem in which unfavorable jointing creates a rock wedge on the bench above a blast. The numerical predictions of wedge stability are compared to the wedge energy model described by Wong & Pang (1992).

Feb 1, 2020

By Neal Lee

Reduced relief horizontally means an increase in energy expended vertically into the rock surrounding the stemming column, and potentially through the stemming column. The vast majority of holes in any surface blasting operation are afforded two horizontal relief faces at the moment of firing, whether by existing relief faces in front of and to one side, or previously blasted hole(s) in front of and to one side of the holes in question. When the energy expended in any hole on the blast pattern has less than two Horizontal Relief Planes or faces (referred to moving forward here as “HRPs”) available to it at the moment of firing, a higher percentage of the available energy is directed vertically. In the analysis of recorded videos by the author, one will note the fact that stemming ejection/flyrock is observed to a much greater degree from the center of almost all patterns when they are timed to “pull out of the middle” (“box cut" timed patterns). This is because the first hole to fire in each row has only one Horizontal Relief Plane, which significantly decreases horizontal avenue for energy release for these holes. This of course results in an increase in the amount of energy expended vertically. This paper proposes a novel methodology to modify the stemming to better use the explosives energy of each hole, while controlling side effects such as flyrock and airblast.

Feb 6, 2023

By Frank Hirthammer

Since the introduction of the Explosives Track & Trace in Europe in 2014 for manufacturers and 2015 for end-users, a lot has changed in all areas of the supply chain and the use of explosives. The regional associations, manufacturers' organizations, and trade associations have proven that it is possible to overcome a hurdle, that looks almost impossible in the beginning, through consistent cooperation. The paper gives an insight into the problems involved in introducing such a requirement, identifies ways and solutions, and concludes them. When looking at the current situation, the paper describes the process by which a prescribed change in business processes are transforming into a solution that increases productivity, security, and handling.

Feb 1, 2020

By Manuel Calderón

Chile is responsible for 30% of the global copper production; the world ́s largest. However, significant challenges are faced in this industry; declining grades (1.13% in 2002 to 0.61% in 2015), high cost of energy, scarcity of water, and environmental concerns. Mining trends suggest the future of the industry will be focused in the underground space, specifically due to the depletion of economically viable surface mineral deposits. For example, the largest block cave mineat Codelco ́s Chuquicamata mine is expected to reduce energy costs by 50% and dust emissions by 97%compared to the open cut mine. To access these underground deposits, critical infrastructure is required; horizontal tunnel developments, extraction levels, vertical raises, and ore passes with the on-time delivery of the highest quality outcomes being a requisite for successful project delivery (Lift 1 of 3 at Chuquicamata Underground has over 1000drawbells).One aspect that makes this scenario even more challenging for deeper underground operations is the increased risk profile (people, equipment, and geotechnical) that forms part of the general environment. Furthermore geotechnical risks should be considered and they include rock burst and windblast. The safe interaction with this environment must be sustainable throughout the full life of the project. This paper presents the Enaex group approach to addressing the blasting challenges and outlines the solutions created. Aspects such as rock mass damage occurrence as a function of blast vibration frequency content has been studied, as well as the development of blasting methodologies for guaranteeing the full 100% extraction of all infrastructure blasts, including the all-important draw bell volumes. The development of such infrastructure volumes in one single event using electronic detonators and the associated achievement of ambitious productivity goals, are described as a critical part of the successful construction of one of the most ambitious UG projects currently present on the world.

By Frank Hirthammer

Since the introduction of the Explosives Track & Trace in Europe in 2014 for manufacturers and 2015 for end-users, a lot has changed in all areas of the supply chain and the use of explosives. The regional associations, manufacturers' organizations, and trade associations have proven that it is possible to overcome a hurdle, that looks almost impossible in the beginning, through consistent cooperation. The paper gives an insight into the problems involved in introducing such a requirement, identifies ways and solutions, and concludes them. When looking at the current situation, the paper describes the process by which a prescribed change in business processes are transforming into a solution that increases productivity, security, and handling. It shows examples from daily work, in which possibilities for optimization, improved quality assurance, and work facilitation are explained. It presents the resulting potential by comparing process flows, before and after the introduction of Track & Trace solutions. What challenges will we face in the future concerning the use of T&T solutions? Will the tracking of explosives become the norm worldwide? What are future hardware and software developments to be expected? What impact will this have on the global supply chain?

By Dr. Anurag Agrawal, Steve Franklin, Clint Zimmerman, Elijah Williams

In a time when data has become a highly valued commodity within many mining and quarry operations, managing large amounts of current and historical information can be difficult. If not managed properly, trying to leverage the data to make informed operational decisions promotes another challenge. Geographic Information System (GIS) is an environment that uses computers and software to create, manage, analyze, and map all types of data. Currently, the mining industry is faced with a challenge to produce the demanded critical metals and minerals that drive our economies. GIS is leveraged in many large mining industries today to help drive decisions, save cost and plan for future operations. Specifically in the Drilling, Blasting and Quarrying industries, data is being captured at many different levels, whether it is a subsurface geological, blast performance, quarry surveys, loading and hauling, or crushing performance. Pen and paper logs and reports compiled lack the dimension that GIS can bring for extracting value from real-time or historical data. GIS connects data to maps, integrating location data with all types of descriptive information. Paired with Artificial Intelligence, additional analytical layers can be built on platforms to extract data and automate workflows. Having the ability to encompass several forms of collected data to drive operational decisions can bring huge savings to the bottom-line. This paper will dive into the areas where GIS data can drive value into operations by assisting in the management and analysis of the types of data being captured, specifically with Drill and Blast. Whether it is tracking haul road conditions, monitoring locations of equipment, environmental conditions, quantifying blast performance or developing a quarry plan based on geological models. GIS can collectively encompass all of this data to bring tremendous value to the operations, improving safety, efficiency and production.

Jan 21, 2025

By Manuel Villalobos Calderón

This paper presents the Enaex group approach to addressing the blasting challenges and outlines the solutions created. Aspects such as rock mass damage occurrence as a function of blast vibration frequency content has been studied, as well as the development of blasting methodologies for guaranteeing the full 100% extraction of all infrastructure blasts, including the all-important drawbell volumes. The development of such infrastructure volumes in one single event using electronic detonators and the associated achievement of ambitious productivity goals, are described as a critical part of the successful construction of one of the most ambitious UG projects currently present on the world.

Feb 1, 2020

By Winfried Rosenstock

AEBT has been available for a couple of years and is successfully applied in Australia. Up to now it was mainly used in coal surface mining at the Australian East- Coast. Presently, the proved results reach ~ 50 % reduction of Drilling & Blasting costs and a productivity increase of between 10 and 20 %. In 2003 it was for the first time used in surface metal-mining. The mine features for the time being an extremely difficult geological environment and had above to be carried out in the transition level waste/ore. Reductions of wall control, powder factor and vibrations were the main target.

Jan 1, 2004

By Jorge Cárdenas, Luis Huaroc, Máximo Cari, Nestor Delgado

In Peru, after four years of pandemic, some mining companies have chosen to install integrated operating centers in central offices where through network technology and video surveillance it allows them to carry out their activities remotely, this has become a disruptive strategy to promote a safer and smarter mining industry. Our fundamental value is to improve the quality of life, safety and well being of our collaborators, that is why we have created the remote blasting engineering control center " Core" that allows us to humanize mining. Core is an integration of experience, security, technology, quality of life and artificial intelligence; it has media technology connected directly to the mining operation, specialist engineers and technical assistants in team they seek to create optimal proposals of drilling and blasting designs remotely that generate added value to customers. In the planning process the team suggests drilling meshes, in the loading process there are optimized, digitized designs and efficiency in the factory trucks finally in the safety process allows us to identify inadequate pipes within the blasting project, deviation of procedures, remote inspections, identify operating conditions to prevent future risks that may arise in the blasting process. The remote communication systems allow you to monitor mining operations remotely to identify and alert any operational or security deviation that was not identified by the personnel present in the operation, as well as to store images in case investigations are required. The results obtained have allowed us to reduce the exposure of personnel to any risk of the mining operation, to optimize times in the activities of our engineers who are in the mining operations since there is the permanent support of centralized specialists to face every challenge that arises in the operation, for the engineers who are in the offices of Core can be very close to the family and do not lose it, and for our customers it is to meet their needs with engineers specialists in the drilling and blasting process, as well as in safety to be able to proactively cope with any deviation that arises.

Jan 21, 2025

By S. Evans, J. Phillips-White, D. Morton

The partnership between Orica and MMG at the Dugald River Zinc mine in Australia has led to the first global field trials and deployment of Orica’s Subtek™ 4D™ (hereafter referred to as 4D) Bulk Systems underground bulk emulsion blasting technology. This technology offers advantages over conventional bulk explosives by extending the range of energy and length of explosive column that can be charged in underground production. 4D gives blast designers energy options between Relative Bulk Strength (RBS) 50 - 150, delivered uniformly along the entire column in most blasthole conditions along with the ability to instantaneously modify the energy within an individual blasthole. During Phases 1 – 3 of the project from October 2022 to January 2023, over 57 tonnes of the 4D Underground emulsion were loaded in 17 stopes. The primary objectives of this phase were to reduce hanging wall dilution and improve stope recovery. While drilling and other parameters remained unchanged, the energy selection was tailored for specific situations, guided by a revision to the site's drill and blast standard. The design used low energy (RBS 50 - 70) in holes adjacent to the hanging wall and high energy (RBS 130 - 150) where stope recovery had historically been challenging, such as at the toes of long downholes. Initial results of the project focused on five stopes selected for their similarity to those used for the baseline data set. Although the 4D data set was small, the post-blast scans indicated favourable results for recovery and dilution. This suggests that selecting and delivering bulk explosive with tailored energy levels can improve stope performance.

Jan 1, 2024

By Juan Pablo Henríquez, Sebastian Lozano, Constanza Soto, Gonzalo Segura, Carlos Torres, Danko Morales

The Atacama Kozan underground mine, located in Tierra Amarilla, Atacama, Chile, was facing over-excavation and slow progress in drift construction, issues associated with the use of traditional explosive, ANFO. The presence of water in the blast holes required as well the use of cartridged emulsions, which extended loading times and increased operators’ effort. With loading times ranging around 76 minutes and lower advanced rate, Enaex Underground proposed the use of a pumpable emulsion-type explosive to optimize blasting, enhance safety, and streamline the operational process. This explosive is loading into the blasting holes using an UBT equipment (Unidad Bombeable para Túneles in spanish). This equipment allows mechanized loading, adaptation to small and medium diameter boreholes, ensuring compatibility with varying drilling profiles, integration with Atacama Kozan’s operational equipment and improvement in environmental and occupational conditions, with a measurable reduction in contaminant emissions and worker exposure risks. The implementation of this emulsion-based explosive allows an increase in productivity in drift development. A notable effective advance rate of 95% to 96% was achieved, alongside a reduction in overbreak in 7%, and a decrease in loading time to 40 minutes. Additionally, there was a 40% occurrence of drilling half cast, contributing to contour drift quality. The operation also benefited from a cleaner and safer working environment, enhancing operator ergonomics and reducing the need for jetanol and compressed air.

Jan 26, 2026

By Jonathan Heiner

Rio Tinto Bingham Canyon Mine started its South Wall Push Back (SPB) in 2011. This push back will mine through the only road to the pit bottom (the 10%). The pit bottom is the main ore sector for the mine and supplies about 80 to 90% of the ore. In late 2017 the mine set off a blast in SPB that created a small wedge failure on the high wall between SPB and the 10%. This wedge failure released a rock approximately 20 minutes after that blast that rolled down the wall landing on the 10% near and then contacting a light vehicle

Jan 1, 2019

By Peter Moser, Andreas Grasedieck

In modern rock blasting it is becoming more and more important to achieve a certain specified fragmentation. This means that the rock particles formed as a result of the blast should conform to a desired particle size distribution. An important issue with respect to achieve a desired blast result in terms of fragmentation is both the availability of models for the prediction of the characteristic of the particle size distribution of blasted material and the determination of the energy necessary to achieve a certain fragmentation status. Within the research project “Less Fines” funded by the European Union under project reference G1RDCT200000438, the latter has been addressed by the Department of Mining Engineering& Mineral Economics of the University of Leoben. For that purpose fragmentation results from lab scale blast tests have been analyzed and the relationship between the specific charge used for the blasts and the resulting specific surface of the fragmented material has been examined. Linear relationships between the specific charge and the specific surface of the resulting fragmentation were found for various types of rocks to apply over a range of 10 for the powder factor.

Jan 1, 2004

By L. Muñoz, L. Steffen, W. Vilas

The emission of particulate material is one of the several parameters related to environmental control in mining operations near communities. Blasting is an event that generates and leaves a large amount of dust in suspension, which can cause discomfort to communities, generating complaints that can compromise the operational continuity of the mine. The proper management of these environmental impacts is a key factor to ensure a good relationship with the neighborhoods, making a responsible mining in harmony with the environment, giving sustainability to the mining business in the medium and long term. The main goal of this work is to present different techniques and technologies applied in a large-scale open pit mine in Brazil, with operations close to a community, to minimize the emissions of particulate material into the atmosphere. For this, different technical solutions were implemented. First, a non-conventional blasting technique was introduced that incorporates special charging and timing configurations, generating a first upper layer that serves as a blanket to contain a second, higher-energy lower layer. An optimal stemming was also defined in order to minimize ejections and maximize cratering, using the scaled depth of burial theory as well as video and fragmentation analysis. In addition, changes were made in the timing between decks (to guarantee a minimum time between layers) and between holes (changing the initiation point opposite to the free face). Finally, additional measures such as humidification of the bench, use of a wind vane to identify wind direction and the construction of a physical barrier between the mine and the community were implemented as additional mitigation measures. By applying the above techniques together, in some specific zones of the mine, it was possible to considerably reduce the ejections generated by blasting versus conventional blasting without the above measures, which was demonstrated in the field with dual blasts trials. Additionally, it was possible to achieve a vibration reduction in the community of ~30%. This work demonstrates how, by applying these technical solutions, it was possible to minimize the dust and vibrations generated by blasting allowing this operation to do sustainable mining

Jan 1, 2024

By Clayton Thompson

Linear detonation wave generators (DWGs) shape a detonation wave so that every portion of the wavefront reaches the target “line” simultaneously. A projection-type linear DWG uses Gurney plate velocity predictions and Taylor deflection angle predictions to estimate the angle at which a thin projected flyer (typically metal) will impact a target. A mousetrap-style planar DWG consists of two projection-type linear DWGs working in succession to create a planar wave-front through shock initiation of each successive target explosive. The angle of deflection is critical to yielding a planar or linear wave profile. Gurney predictions, nominally accurate to within 10% of empirical results, may not yield ideal linear or planar detonation behavior when used with a grazing projection-type DWG, which typically requires accuracy within 2%. Simulations were conducted using AUTODYN hydro code to compare deflection angle prediction methods. Ranges of minimal error between Gurney and Taylor predictions and the results from the hydro code were determined, using PBX-9404-driven polyethylene flyers.

Jan 1, 2011

By M. Syafiq Isnaya, Rahma Norfaeda, Slamet Rachman Jaka

This paper is about project improvement to maximize energy distribution while ensuring beneficial blast results (reduce boulder condition). The main problem is how to manage complex lithology conditions related to detonation propagation in energy distribution control.

Feb 1, 2020

By S. M. Geerts, M. T. Wild

In this paper the performance effects of various shaped charge liner designs will be discussed. Several different charges will be tested and the liner design will be reviewed based on the performance in testing. The first type of shaped charge to be tested is a conical charge with dual confinement. For the purpose of this paper, dual confinement is a shaped charge with two liners but containing one explosive charge. Several charges with different dual confinement designs will be tested. Variations in configuration include charges with similar angle and similar diameter. The second type is a double conical shaped charge configuration. A double shaped charge will be considered to be two complete charges formed into a single cone. The goal of the project is to determine if any of the designs increase the efficiency and/or effectiveness of the shaped charge in comparison to the standard conical shaped charge. A standard conical charge will be detonated against a witness plate to get a standard depth of penetration or a baseline. All charges will have a seven cone diameter standoff, allowing the data to be compared to the control charge. Computer modeling will be used to predict the results of the testing that will be conducted. The actual results will be compared to the computer simulation for validation.

Jan 1, 2010

By Robert L. Martin, Brian W. Stump

"The Black Thunder Mine is located in the Powder River Basin of Northeastern Wyoming. Over 39.2million tons of coal were produced at the Black Thunder Mine in 1996. Just over 100 million pounds ofANFO/Emulsion blend were consumed in that same year. Currently around 30% of the overburden is cast to final with the use of explosives. With plans for a mine expansion, explosives will continue to play a very vital roll well into the future."

Jan 1, 1997

By Charles Zdazinsky

Many blasting applications in the mining industry demand that the hard rock being blasted remains structurally competent. For example, pre-splitting is a common technique to reduce fracturing, and operators of dimension stone quarries use this blasting method to eliminate overbreak. When pre-split design parameters are not applied correctly, there will be a redistribution of stresses within the rock, resulting in Blast Induced Rock Damage (BID). Advances in geophysical technology are enabling blast technicians to monitor BID and then use the results to correctly design their blasts.

Jan 1, 2011

By Romel B. Villanueva

At the Yanacocha gold mine, in the Andes of northern Perú, the first instrumental tests were carried out in October 2019 to detect the initiation sequence of a production blast by detecting the EMF signal produced by the detonation from each blast hole in the sequence. Several experimental tests were carried out to choose the correct antenna and find the best setup of the high-speed Data Acquisition device (DAD) to detect these electromagnetic waves. Finally, the first measurement was obtained. With the instrument recording at a rate of 1 million samples per second, the initiation sequence was detected with 99.5% accuracy. It was found that it corresponded, without a doubt, to the designed scheme. The main result is that these tests provide us with a method and instrumentation to verify if the planned initiation sequence is carried out correctly in the field. In this way we can find operational deviations and detect possible misfires. This method has proven to be accurate, fast and easy to implement, mainly requiring an EMF signal capture equipment that can record at very high speed, something that is increasingly easier to satisfy with the development of microcontrollers. On the other hand, the type of antennas used in this method are low cost and very commercial. These tests have improved our understanding of the nature of detonation and have marked a new milestone in the development of blasting instrumentation in Peru.

Jan 21, 2025