Search Documents

By K. Lillkung

The use of secondary sources has become a very attractive option in the production of platinum group metals as the demand for these metals has increased. One of the promising sources are the spent catalysts, which provide an attractive source as they have relatively high metal content compared with the ores where the metal is originally extracted from. The concentration of platinum group metals in catalytic converters is in the range of 0.1-1 mg/g as the concentration in ores is usually less than 10 ppm. Aqueous chloride solutions are claimed to be a cost effective way in which platinum group metals can be brought into solution and concentrated. In this work the effect of different parameters on the dissolution rates of Pt, Pd and Rh were investigated. The parameters investigated were the Cl- concentration, the temperature and applied potential. Chloride concentrations used were 62.5, 90, 125 and 250 g/l. Temperatures were 25, 40, 60, 80 and 94°C. Potentials were 950, 1050, 1150 and 1250 mV vs. SCE for Pt and Rh and 380, 410, 440 and 470 mV vs. SCE for Pd. Dissolution rates were calculated from the current densities determined by potentiostatic measurements. Thin wire electrodes were used in the measurements. As expected, higher temperature, higher potential and higher chloride content generally increasedthe dissolution rate. However, the effect was nonlinear and slightly different for different metals. The results show that strongly oxidizing conditions are needed in order to achieve reasonable dissolution rates. With the highest chloride content and at potential of 1250 mV vs. SCE and 94°C the dissolution rate of Pt was nearly 1 mm/h, whereas in similar conditions Rh achieved a rate of only nearly 100 µm/h. Similarly, with the highest chloride content and at potential of 470 mV vs. SCE at 94 °C the dissolution rate of Pd was nearly 1 mm/h. Keywords: Pt, Pd, Rh, redox potential

Sep 1, 2012

By E. L. Chanturiya

During the mineral processing of pyrites sulphide ores of some deposits of Russia loss of gold with tailings and pyrite concentrates amounts up to 40%~90%. The problem of selective allocation of gold-bearing pyrite is crucial. There are 4 mineralogy-technological groups of pyrite determined in copper-zinc sulphide ores, based on the increase of contents of gold in pyrite. The gold associated with group 4 pyrite contents of 85% the total mass of gold found in the pyrite. The flotation behaviour of the enriched fractions of pyrite (98%), of the allocated from the ore of Gay deposit, were studied essentially in various conditions ?? and the charge of Butyl xanthogenate of potassium (ButX). Some products of selective pyrite flotation were investigated by methods of scanning electronic microscopy, energy-dispersive and X-ray spectral microanalyses, definition of specific resistance and thermoelectric moving force.

Jan 1, 2014

By B. A. Kutlin, S. A. Ropeyko, N. A. Yurlova

"The aim of NPO RIVS research and practice activities is to minimize impact of the mineral processing plants (MPP) on environment by using new concentration methods, high-technology equipment, implementation of engineering solutions directed to reduce emission of polluting substances (PS) into atmosphere, application of low-waste technologies, decrease of water withdrawal from a surface water or groundwater source for process needs. In our studies environmental safety of mineral flotation is provided through technologies using highly selective chemicals, that leads not only to reducing reagent consumption, and production of saleable products of high content of extracted minerals, but also to reducing pollutant emissions, decreasing supply of surfactants (SAA) in natural geosystems, primarily, in ground and surface waters. Decrease of water withdrawal from a surface water or groundwater sources for process needs can be achieved by using closed circuits and waste water treatment for further use in process operations, recycled water conditioning to obtain optimum quality parameters for process operations of concentration. Concentration in water (wet processing), tailings dewatering and semidry and dry (filtration cake) stockpiling in tailing ponds, efficient dust-collecting systems contribute to pollutant emission reduction. Use of mineral wastes – concentration tailings as a source of valued components, facilitates efficient use of natural resources and reduces wastes and its impact on natural ecosystems due to smaller areas of damaged lands during waste products disposal. Process and engineering solutions of NPO RIVS that allow diminishing impact of MPP on natural environment (NE) have been implemented in mining and processing complexes of Russia, Kazakhstan, Ukraine, Kirghizia and Mongolia. Compliance with environmental safety requirements contributes to enhancement of mineral processing and sustainable mineral development.INTRODUCTION Mining and processing complexes have a significant impact on environment as a result of extraction and recovery of mineral resources, landscape changes, waste disposal and, as a consequence, pollution of soils, surface and underground water sources. Therefore, the aim of the operation of the mineral processing enterprises in its research and practical activities is to reduce impact on environment due to new beneficiation technologies, high-technology equipment, implementation of engineering solutions directed to reduce emissions of polluting substances (PS) into atmosphere, use of low-waste technologies, decrease of water withdrawal from a surface water or groundwater source for process needs. Compliance with the requirements of environmental safety encourages advancement of mineral processing technologies and sustainable mineral development. Concentration in water, tailings dewatering and semidry and dry (filtration cake) stockpiling in tailing ponds, efficient dust-collecting systems contribute to pollutant emission reduction. Use of mineral wastes – concentration tailings as a source of valued components, facilitates efficient use of natural resources and minimizes waste formation and its impact on natural ecosystems due to reduction of damaged land areas during waste disposal."

Jan 1, 2018

By Kremena Dedelyanova, Tsvetan Damyanov, Nikolay Hristov, Evgeni Kostadinov, Lubomir Kuzev

"Spherical grinding media (balls) are the most widely used media for comminution of ores by grinding. One way to optimize the grinding process in a tumbling mill is associated with the development and testing of a new media shape. By modelling simulation study of the behaviour of two types of grinding media (balls and tetraballpebs) in the grinding process was conducted to determine the possible advantages of the new media shape. Tetraballpebs are in the shape of tetrahedrons with spherical convex walls. D305 mm and L305 mm Bond ball mill sizes were used in the experiment. They are modelled milling tetraballpebs bodies corresponding by weight to five ball sizes, namely ¾, 7/8, 1, 1¼ and 1½ inches which form the grinding media used in a Bond ball mill. They are cast steel grinding bodies. Studies carried out with both types of grinding media include equal number of milling bodies of the same weight and volume. Having thus ensured a uniform mass of the grinding media and the same number of milling bodies, all other conditions and process parameters being identical, conclusions can be drawn about the influence of the grinding media shape on the grinding process. Compared to steel balls, the tetraballpebs used in laboratory tests carried out in closed cycle by Bond ball mill and the study of the rate of grinding gave five to six per cent higher yield of a control size of minus 0.1 mm. Measurements of the Bond ball mill power consumption demonstrated that tetraballpebs grinding media achieved energy saving of 4.7 per cent for the production of one gram of the control size of minus 0.1 mm."

Jan 1, 2014

By T. Surkova

For the moment reserves of high-grade ores are practically depleted requiring ever-increased involvement of low assay raw materials, such as black-shale ores, in industrial operations. Black-shale ores are constituted of minerals containing such valuable components as vanadium, uranium, molybdenum, manganese, and rare-earth elements (REE). We studied technogenic solutions of black-shale ores processing, after uranium, molybdenum, and vanadium were recovered. Mentioned solutions contain rare-earth elements in substantial quantities (S REE 70-100 mg/dm3) that is very important factor taking into consideration the world demand ever-increasing last years. Higher concentrations of iron and aluminum inhibiting REE sorption and extraction recovery are found in solutions. We propose a method of hydrolytic deposition to cleaning solutions from impurity elements (Fe, Al). Study of hydrolytic deposition kinetics allowed identifying optimal conditions to run this process. Rare-earth elements may be recovered from purified solutions through sorption process followed by their further deposition from eluates in form of concentrates. Keywords: black-shale ores, rare-earth elements, a method of hydrolytic deposition, impurity elements, sorption

Sep 1, 2012

By Brian Loveday, Sandile Nkwanyana, Indresan Govender

"Recent batch experiments by the authors in a pilot scale ball mill (Ø = 0.6m) have demonstrated that a partial replacement of the ball charge by pebbles (25 % pebbles; 75 % steel balls) optimally reduces the ball and power consumption without altering the rate of production of fine material (passing 75 microns). At higher pebble volumes, the production rate of fines was reduced progressively. With the 25/75 composite charge a saving of 13 % in power consumption was achieved, and a saving of 25 % in steel ball consumption is implied. A partial replacement of steel balls by pebbles reduces the overall density of the grinding media in the charge. Taking into consideration that the production rate of fines is usually proportional to the bulk density of the charge in the mill, it would be expected that a composite charge (e.g. 25/75) would coarsen the grind and consequently reduce the rate of production of fines. Pebble wear contributes a small proportion of fines and it doesn’t provide a full explanation of why the 25/75 composite charge has no (or minimal) adverse effects on the rate of production of fines. Clearly, the production of fines across the mill is directly related to the shear and compressive power dissipation density. Accordingly, we hypothesise that the spatial power dissipation distribution meeting the minimum requirements for fines production— at the so-called active regions—are equivalent, or minimally comparable, for both the 25/75 composite and 100 % ball charge operating conditions. To test the hypothesis, we performed DEM simulations to analyse power dissipation in the active regions. 1. INTRODUCTION Comminution remains to be the most expensive process in mining operations, particularly because the energy consumed in this process accounts for 30-70 % of the total cost of a mining operation (Nadolski et al, 2014). Optimization of comminution circuits has been focussed on reducing capital and operating costs and maximising throughput capacity. For existing operations, it is often a challenge if the optimization process recommends retrofitting new ‘major’ equipment. The challenge arises from new capital cost and the difficulty of retrofitting in an existing circuit, while maintaining production (Major et al, 2001). Thus, for existing mining operations, optimization of comminution (cost and throughput) is often limited to operating conditions and/or addition of auxiliary equipment (such as pebble crushers, additional screens and high pressure grinding rolls (HPGR)) (McIvor and Greenwood, 1996; Hart et al, 2001; Powell et al, 2015b)."

Jan 1, 2018

By B. Suresh

Iron ore in Bellary-Hospet region is friable in nature and generates a significant amount of micro-fines (-150 µm) during mechanized mining, handling and processing. Present beneficiation practice generally employs spiral classification followed by hydrocycloning to remove slimes (-15 µm). The iron ore fines, beneficiated at JSW Steel Ltd., Karnataka generates tailing having 48-52% iron content in the form of slimes, which accounts for 50 to 55% by weight with respect to classifier overflow. The loss of iron as slime is considerably high. In this context, laboratory studies were carried out with different combination of beneficiation techniques with an objective to develop an efficient flow sheet to achieve better product grade and recovery from classifier overflow. The results revealed that de-sliming process by hydrocycloning in combination with either magnetic separation or froth flotation leads to increased iron loss in tailing. Based on investigation it is observed that forward flotation is beneficial over the reverse flotation. The experimental approach of forward flotation on classifier overflow followed by magnetic separation on flotation tailing resulted in overall product grade of 62.9% Fetotal and 70.3% yield. The tailing contains 34.6% iron, which accounts for 29.7% by weight with respect to classifier overflow.

Sep 1, 2012

By Dmitriy Makarov

The paper presents the modeling and analysis of oxidation of pyrite copper-zinc ore samples from the Letnee, Yaman-Kasy and Valentorskoye deposits. It is found, that the oxidized samples contain copper and zinc sulfates that are leached under the sample and water contact. It is shown, that sulfide floatability is decreased by the longer-term oxidation.We advise to improve nonferrous metals recovery by joint leaching and ultrasonic treatment of oxidized compounds. Study of the geotechnological processes of non-ferrous metal extraction, on the basis of two copper-zinc ore deposits shows, that heap leaching is of little use for the ores of the Letnee deposit. Leaching results for the Yaman-Kasy ore showed more promise.

Sep 1, 2012

By Fengnian Shi

In the current energy-sensitive world, sustainable development in the mineral industry will require new, better and more efficient processes. Novel comminution methods, which offer the prospect of achieving the required outcomes of size reduction and mineral liberation at lower energy consumption, are continually being sought. In the past five years, extensive research using high voltage pulse electrical comminution technology has been carried out at the Julius Kruttschnitt Mineral Research Centre (JKMRC), in collaboration with selFrag AG. The major outcome of this research is the development of the concept of pre-weakening ore particles by electrical comminution procedures to reduce the energy consumption in the downstream grinding circuit. The research has also verified the preferential liberation of valuable minerals by electrical comminution. Given the advantages, several potential applications of electrical comminution in the mineral industry are proposed, including AG/SAG mill feed pre-weakening, pebble treatment, ball mill feed pre-weakening, early recovery of the liberated valuable minerals, crack/micro crack generation for improved leaching, and smelter slag treatment. For the mineral industry to utilize electrical comminution, two emerging issues identified from the research need to be address. They are the energy consumption by electrical comminution in the locked cycle treatment and the facilities scale up necessary to move this technology from the laboratory to the plant. Keywords: high voltage pulses, electrical comminution, energy efficiency, mineral liberation

Sep 1, 2012

By Z. S. Abisheva

Results of the study targeted to development of universal acidic-extraction-precipitation technology for gallium recovery from the sublimates are presented in the paper. This will let to utilize a new non-traditional source for gallium production. Phase composition of gallium containing dust was studied. Forms of gallium in the sublimates were determined. The main form is Ga2O3, however, GaP form is also present in the cottrel dust and Na5Ga3F14 form is present in the dust of aluminum electrolysis. The possibility of gallium concentration was established via secondary pyro-selection of the dust. Kinetics of interaction of dust components with sulfuric acid was studied. The products of the interaction subsequently were leached with water. Optimum conditions for direct leaching with HCl and H2SO4 were determined providing gallium recovery from the cottrel dust and the ash carry outs up to 95 %. Gallium recovery from the primary dust and the secondary dust of aluminum electrolysis was at 52; 64 % and 63; 83 % respectively. Effect of Fe, P, K, Na and Al admixtures for gallium extraction from hydrochloric acid solutions was studied. It was shown that gallium chloride complex (GaCl4-) is extracted into the organic phase from the following acid mixtures: HCl + H2SO4, HCl + H3PO4, HCl + H2SO4 + H3PO4, HCl + HF. Kinetic regularities of gallium extraction in the system (tri butyl phosphate) TBP ? HCl - Ga were studied using diffusion cell method with agitation. Optimum conditions for gallium extraction from complex hydrochloric acid solutions with TBP were found providing 99.9 % recovery and separation coefficient for gallium and iron (III) of more than 25 in one stage. Sodium hydroxide and water were selected as reagents for re-extraction of gallium from the organic phase. Different options for disposal of by-products that are formed in the processing of cottrel dust, ash sublimates and dust of aluminum electrolysis were proposed and tested. Keywords: gallium, kinetic, sulfatization, leaching, extraction, technology

Sep 1, 2012

By A. A. Lavrinenko

There are discussed the possibilities of using of flotation tailings of platinum-copper-nickel sulfide ores of the Norilsk region for the preparation of backfill mixture instead of a specially produced rock and binder materials to reduce the cost of stowing operations and impact on the environment. It is shown that due to the presence in the tailings of flotation up to 10% of sulfide sulphur, which reduces the strength of the fill materials, and more than 1 g/t PGM it is necessary the preliminary extraction of the sulfides in the product for further processing that give an opportunity to reduce the losses of valuable components. It is shown that by the flotation of the current tailings it is possible to extract 91% of sulfide sulphur, 60% of palladium and 30% platinum in 17% sulfide concentrate containing 2.1 g/t palladium, and to reduce the sulphur content in the tailings up to 0.7%. Due to the easy oxidation of pyrrhotite, there is recommended fractional delivery of the collector with a total consumption 200 g/t. There are discussed results of the flotation study with an additional collector of PGM (sodium diizobutyditiophosfinate), which one show the possibility to increase extraction of platinum on 45%, as well as extraction of sulphur and palladium. For the flotation of sulfides and PGM from the current tailings there is recommended a combination of collectors for primary flotation and only butyl xanthate using in control operations. The possibility of using sludge fraction of the current tailings as a component for the preparation of the combined cementing materials after exposure of sulfides is analyzed. It is shown that the efficiency of the flotation of sulfides from this fraction can be enhanced using selective flocculants. There are discussed the advantages of implementation of completely hydrophobic butadiene-styrene copolymer in comparison with partially hydrophobic polymers. There is discussed an efficiency of the mechanochemical treatment of old tailings in turbo mill and sulphuric acid to remove oxide films from the surface of pyrrhotite before its flotation. Due to the pretreatment operation there is achieved increasing of sulphur extraction and after the introduction to the flotation circuit three control operations there is produced the fill material with sulphur content 2.5%. Keywords: tailings, copper-nickel ore, pyrrhotite, butyl xanthate, sodium diisobutyl dithiophosphinate, selective flocculation, butadiene-styrene copolymer, mechanochemical treatment

Sep 1, 2012

By Xiao Ni

Alkyl hydroxamic acid was shown to be a suitable collector for the flotation of pyrochlore from carbonatite niobium oxide ores. In the direct batch rougher flotation from the ore without desliming, over 85% of the pyrochlore can be recovered at about 30% mass pull. Cleaner flotation tests showed that the rougher concentrate can be upgraded. The adsorption mechanisms of octyl hydroxamic acid (OHA) were studied by using high purity pyrochlore and calcite mineral samples and employing analytical measurements such as Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS) and UV/VIS spectroscopy. FTIR showed a shift of the vibrational frequencies of the carbonyl group in hydroxamic acid after adsorption on pyrochlore and calcite, and the shift was more pronounced on pyrochlore. XPS results indicated a lowering of the binding energies (chemical shift) of Nb3d5/2 and Ca2p3/2 electrons on pyrochlore, and the lowering of the binding energies of Ca2p3/2 electrons on calcite, again with the shift being more pronounced on pyrochlore. The results indicated hydroxamic acid formed stronger complexes with pyrochlore than with calcite. Adsorption isotherms indicated that OHA adsorbed more on pyrochlore than on calcite at low concentration. At high concentrations, the adsorption densities on both minerals were similar. All results explained the observed selectivity of the reagents in the flotation of the carbonatite niobium oxide ores.

Sep 1, 2012

By Silvia França, Hudson Couto

"In this paper, an alternative beneficiation process was developed to recover nickel minerals from low-grade weathered ores. The studied sample, 0.3% Ni grade, is essentially composed of nickel sulfides (pyrrhotite and pentlandite); magnetite and silicates (mostly talc and amphibolites) are the primary gangue minerals. The particle size distribution was controlled using a grinding operation to avoid producing an excess of fine particles by overgrinding. The sample underwent a grinding step for the fine degree of liberation. The slimes (-20 ?m) were removed via two desliming stages in hydrocyclones (diameters of 1.5" and 2"); the ground material, which was classified in a range of (-150+20) ?m, was processed by column flotation in three different stages: rougher flotation for magnesium silicates, rougher flotation for sulfides, and cleaner flotation for sulfides, using pilot flotation columns (2" and 6" in diameter and 20 ft high). The goal of using the preliminary magnesium silicate flotation step was to remove hydrophobic minerals (mostly talc) that would float naturally with the sulfides, which would decrease the Ni grade in the concentrate, as well as to reduce the MgO content because this compound is considered harmful in metallurgical processes when a grade greater than 9% is used. The final concentrate obtained in the cleaner flotation step reached up to 2% Ni and 7.0% MgO. The global and flotation recoveries in the process were approximately 30% and 60%, respectively, due to the losses of Ni during the desliming process. Despite this low global recovery, the adopted beneficiation process can be considered an interesting alternative to produce nickel concentrate from tailings or waste materials."

Jan 1, 2014

By Antoineta Boteva

A significant part of the currently production of the non-ferrous and precious metals is from sulfide ores. Character feature of sulfide ores is the presence in them always pyrite and wide range of different sulfide minerals else. These minerals are the carriers of valuable for industry metals. Due to the low content of the main components, very often call on the use of collective- selective flow-sheets. The extraction of minerals in the collective concentrates determined in a large extent the effectiveness of the collective-selective sheets. In conditions of bulk flotation kinetics to floatate of the various minerals is different. Due to why it is and how it can be used for a more effective selection of minerals ?this is the main task of this report. For this purpose are used results from the bulk flotation of pyrite, copper sulfides, molybdenite, galena, blenda. It is separated and place of host rocks. Base it of large experimentation material, including both electro-kinetic measurements of mineral systems, as well as laboratory flotation tests and factories monitoring it is established kinetics of flotation of mineral particles in conditions of collective flotation. Made an effort to clarify the effect as of the species and the proportion of different sulfide minerals involved in flotation pulp else. Traced was the impact of the density and aeration of the flotation pulp on deferens in kinetics of mineral flotation in condition of balk flotation. The obtained results are used to increase the efficiency of the diffraction flotation of the complex sulfide ores containing precious metals. In the schemes, it is possible precious metals to fall in the most appropriate for the next processing products. Keywords: flotation, sulphide ores, kinetic extraction

Sep 1, 2012

By I. Y. Titov, Victor D. Samyguin, A. Y. Nikitin

"It is suggested that improvement of separation process efficiency in machines and circuits of selective flotation should be based on application of the principle of technology individualization (PIT). This principle is grounded on the following provisions.The mineral composition of ores is used to establish the correlation between the selective reagent mode and the individual value of hydrodynamic conditions of flotation machines together with individual structure of the process flow diagram. The individuality of all sorts of particles identified by methods of process mineralogy was characterized by their distribution according to the rate of flotation (or spectrum). The spectrum identification is carried out by modeling and by experimental and computational method on the data obtained on various types of laboratory flotation machines.The computer-aided test is used to determine the optimal fraction distribution, which reaches the highest possible level of concentration data. The direction of hydrodynamic factors action on concentration data is estimated based on comparison of design base and experimental spectrum. The improvement of separation efficiency in devices is achieved in special-purpose flotation machines (SFM) the design of which provides optimization of hydrodynamic regime in spatially isolated zones. It is demonstrated that the main parameter of SFM operating mode individualization is the rise rate of bubbles going from the chamber into the froth. During this time the composition of particles optimum for separation is formed on its surface. Additionally, it is necessary to coordinate in the zones the residence time of pulp and foam streams with the air consumption. The improvement of separation efficiency in flotation process flow diagrams may be achieved by making several cascades with SFM installed in them. The individual effective structure of the scheme for a definite ores material composition depends on the ratio of particle varieties in the spectrum and is revealed by modeling."

Jan 1, 2018

Results of the study of chloride ion concentration effect to osmium-187 sorption from wastewater of copper smelter with use of foreign anionites of different basicity and structure are presented in the work. It was found that the increase of chloride ion concentration in the wastewater helps to increase recovery of osmium using anionites regardless of their nature. The ways to intensify the process are proposed. The method for osmium elution from the anionites with potassium iodate solution was developed. It was shown that the method lets to recover up to 99% of osmium from the anionites. Recommendations for selection of eluents for better recovery of osmium from the anionites were elaborated. Keywords: wastewater, osmium, anionite, sorption, chloride ions, eluent, recovery

Sep 1, 2012

By Y. Y. Emelianov

The results of the test work of four treatment options of three refractory gold-pyrite and gold-arsenic flotation concentrates are presented. These concentrates were obtained during the concentration of primary ores of large gold deposits. It was found that ultrafine grinding of refractory flotation concentrates did not increase the recovery of gold during subsequent cyanidation. The elimination of sulfur and arsenic during oxidative roasting is 99 per cent. 88-93 per cent of gold is recovered by cyanidation from calcines. After biooxidation of the flotation concentrates with a mixture of strains Acidithiobacillus thiooxidans and Acidithiobacillus ferrooxidans 88-91 per cent of gold is recoverable by direct cyanidation. The recovery of gold from flotation concentrates by pressure oxidation is 88-99 per cent. These results suggest that gold recovery is important but the following strategies would have an impact on a plant performance and would be considered when developing an option to treat refractory ores: capital and operating costs, ore reserves, mine location, infrastructure and qualified staff. Keywords: gold, flotation concentrates, recovery, cyanidation, roasting, biooxidation, pressure oxidation

Sep 1, 2012

By Yuemin Zhao

Pre-combustion cleaning of coal plays a key role in the process of efficient and clean utilization of coal resources. Recently, wet beneficiation of coal is predominant around the world. Nevertheless, wet beneficiation processes are limited by the increasingly serious problem of worldwide shortage of water, especially in China. Thus, it is imperative to develop efficient dry coal beneficiation techniques. Currently, several technologies such as air dense medium fluidized bed, compound dry cleaning and air jigging have successfully achieved high-efficiency separation of 50~6 mm coal. However, in recent years, a large amount of fine coal is generated as the mechanized mining technology has been progressively deployed in coal sector. Thus, it is necessary to develop efficient dry beneficiation techniques for fine coal. In recent years, many countries including China, India, Canada, Germen, and Australia have carried out many research works on fine coal dry beneficiation techniques. China University of Mining and Technology has carried out systematic researches on the introduction the vibrated energy to traditional air dense medium fluidized bed for fine coal beneficiation. This paper studied air dense medium vibrated fluidized beds (ADMVFB) for fine coal dry beneficiation. The experimental results show that the coal of <6 mm size can be beneficiated in an ADMVFB efficiently with the E value of 0.065~0.085, the separating density can be adjusted in the range of 1.45~2.2 g/cm3, and the lower limit of beneficiation can reach to 0.5 mm. Keywords: fine coal, air dense medium vibrated fluidized bed, coal separation, dry separation

Sep 1, 2012

By G. Alfano

We have investigated the breakage actions of solid particles observed in a new generation fluid energy micronizer being set up at our laboratories. The attention has been focussed in particular on breakage caused by interparticle collision, particle impact against a fixed surface, interparticle attrition and particle against wall of jet mill attrition. We have also studied the influence of grain size distribution, maximum particle size, flow rate and characteristics of the solid to be processed, as well as of flow rate and pressure of injected air on the above mechanism. Lastly, the operating parameters of a dynamic air classifier in closed circuit with the micronizer for recovering the fine fraction and automatically recycling the oversize, have been optimized. The findings of this investigation have been used to design, build and fine tune a micronizer capable of controlling the top size of a product having average particle size that meets market requirements for fine powders, while keeping power consumption relatively low.

Jan 1, 2014

By F. Bello, J. Engels

"During 2012 and 2013, Minera Esperanza conducted a series of thickening and deposition trials to identify design and operational parameters associated with increased thickening of its tailings. These trials focused on benchmarking the current solids concentration of tailings (62 - 64%) in anticipation of an increase to 67% solids once two new 45 m diameter deep-cone paste thickeners are commissioned in 2014. These trials studied the sedimentation and rheological characteristics of the existing tailings and performed deposition modelling to assist with developing short- and long-term designs for the tailings storage facility. To verify and optimise these models, Minera Esperanza considered a series of laboratory, pilot, and industrial-scale deposition trials. This paper provides a review of the trials conducted in the laboratory and at industrial-scale and considers the results and optimisations for the short- and long-term design of Minera Esperanza’s tailings storage facility."

Jan 1, 2014