Search Documents

By Bertil I. Pålsson, Sture V. Persson, Kent T. Tano

"Autogenous (AG) and semi-autogenous (SAG) mills often operate in an unstable state because of the difficulty to balance the rate of replenishment of large ore particles from the feed with the consumption in the charge. This has led to an increased interest in obtaining an accurate and direct measurement of mill load and the behaviour of the mill charge. A problem in attempting to measure those parameters is getting a sensor that is both robust and sensitive enough for continuous on-line measurement.Techniques that measure the force acting on the lifter when it hits the charge inside the mill have got an increased interest recently because of the ability to combine it with DEM modeling. This paper presents a method for the measurement of the apparent filling level in a pilot ball mill equipped with the Metso Continuous Charge Measurement system (CCM). In this technique a strain gauge sensor is mounted on a flat steel spring which is fitted into a recess underneath a lifter bar. In addition, a conductivity probe, the Boliden Grinding Measurement System (GMS), is mounted in another lifter bar with the purpose of comparing the two measurements. To visualise the behaviour of the charge a 2D DEM modelling technique is used with Metso HFS software.The pilot mill is a grate-discharge mill, equipped with 12 rubber lifters of square size 0.1 m, face angle 45 degrees. Steel balls in the size range 10-30 mm and density 8000 kg/m3, are used in the experiments. Test material is a hematite pellet feed, d50 around 45um, chosen to get stable grinding conditions with respect to feed size variations.The experiment is meant as a first test of the equipment’s performance, and to study how the sensors respond to changes in some operating variables. To get an understanding of, and distinguish between correlation and causality, experiments are performed according to a full factorial design with two levels, and in addition two replicates of the experiments at a center-point in the charge level setting."

Jan 1, 2003

By S. S. Indi, D. Santhiya, S. Subramanian, K. A. Natarajan

"With the gradual depletion of the high-grade ores and finer dissemination of values in the leaner samples, it has become imperative to develop innovative approaches to process such complex ores. The beneficiation of complex sulphide ores containing copper, lead and zinc minerals, remains one of the most important challenges in base metals metallurgy. The advent of biotechnology in mineral processing has opened up immense possibilities to exploit such difficult-to-treat ores. Bioprocessing techniques thus hold promise as potential substitutes for the conventional technologies in vogue. Several types of autotrophic and heterotrophic bacteria, fungi, algae and yeasts are implicated in mineral beneficiation processes. Adopting a bioprocessing route to mineral beneficiation has attractive benefits, such as lower cost and energy requirements, environmental acceptability and operational flexibility.The interaction of sphalerite- and galena-adapted Bacillus polymyxa (B. polymyxa) cells with sphalerite and galena has been investigated through adsorption, electrokinetic and flotation studies. The amount of sphalerite-adapted cells adsorbed onto sphalerite and galena is found to decrease with increase in pH. On the other hand, the adsorption density of galena-adapted cells onto galena shows a feeble maximum around pH 8, and the amount adsorbed is marginally higher in the pH range of 8 – 11.5. In the case of sphalerite the amount adsorbed is higher in the pH range of 5 to 7. The adsorption density of both the adapted cells is higher for galena vis-à-vis sphalerite. Electrokinetic studies indicate significant surface chemical changes on the chosen sulphide minerals and the bacterial cells, consequent to microbemineral interactions. Selective flotation tests on a synthetic mixture of galena and sphalerite confirm that sphalerite could be preferentially floated from galena, using galena-adapted cells, but not with the sphalerite-adapted cells. The cells adapted to galena assay a higher polysaccharide content and are more hydrophilic, while the sphalerite-adapted cells have a higher protein content and possess greater hydrophobicity. Transmission electron microscopic studies have provided evidence in support of the differences between the cell surface characteristics of sphalerite- and galenaadapted cells (Figure 1). Possible mechanisms of interaction between the minerals and the bacterial cells are discussed."

Jan 1, 2003

By Nóra Schreithofer, Zoltán Jávor, Kari Heiskanen

"One of the challenges the mineral processing industry is facing is caused by the fact that water resources in mining areas are becoming very limited and the cost of water is increasing. The water sources in arid regions often have high salt content. Environmental regulations are forcing plant operations towards completely closing the water cycles within plants. This means that impurities (salts, reagents, ions dissolved from minerals, etc.) accumulate within the circuit that will affect the flotation performance. Water purification can significantly increase the operating costs therefore it should be carefully considered weather the impurities need to be completely removed or is there a tolerable level of impurities that can still be left in the process water without significant deterioration of the flotation performance? Several additional questions arise: what are the tools that help identify what is a tolerable level of impurities? How do the different impurities interact and what is their effect on the process? The effect of frothers on the dynamic properties of air/liquid interface in different size-scales has been extensively studied by the authors in the past. Based on these studies a frother characterization framework was developed that systematically examines the dynamic surface properties of the air/liquid interface in relation to the bubble size. This work can be considered as tool that could be used for the above mentioned purpose. The present study investigates weather the same frother characterization framework can be applied for systems where both frother and different types of salts are present. Nasfroth 240 was used as a frother, in combination with structure-breaker KCl or structure-maker NaCl and CaCl2. Bubble size measurements in laboratory scale mechanical flotation cell and laboratory flotation column and dynamic surface property measurements (dynamic surface tension and dilatational elasticity) were performed. The results highlighted the addition of salt to the frother solutions significantly decrease the bubble size and increase the froth high. The coalescence behavior of bubbles showed correlation between the D32 and ionic strength of salts. The results highlighted that the studied structure maker and structure breaker salts effect the dynamic surface properties in different way."

Jan 1, 2014

By B. Das

The separation of iron values from a typical Indian iron ore slimes containing 57.2% Fe, 5.81% SiO2 and 7.05% Al2O3 by wet magnetic separation and selective magnetic coating is investigated. The iron phases, which are mostly paramagnetic in nature, have been coated with magnetite or colloidal magnetite in presence of surfactant by manipulating the surface properties of the minerals. The studies have indicated that an iron concentrate containing 62.32% Fe with 66.5% iron recovery can be obtained at medium magnetic intensity of 7.8 kG which is much less compared to normal magnetic intensity of 13 kG to14 kG required for hematite-goethite separation. The performance of this technique with respect to both grade and recovery is superior to conventional magnetic separation or flotation of iron ore slimes.

Jan 1, 2014

By Markus A. Reuter, Antoinette van Schaik

"INTRODUCTIONGoods and products, such as passenger vehicles, are manufactured by using a wide spectrum of different raw materials to meet highest consumer requirements during use. Due to the time-varying composition and complexity of multi-component products such as cars, recycling is complicated. It involves a network of interconnected processes and material and energy flows. Improving the efficiency of the material cycle of the car to comply with the recycling targets as imposed by EU legislation, requires insight into all aspects influencing the closing of the material cycle (dynamics, technology, economy, legislation, etc.) and their mutual relation. In order to define the link between recycling end-of-life products, their changing composition and design a dynamic model was developed for the resource cycle of cars. The model integrates the optimisation of the material cycle with the dynamic behaviour of recycling systems."

Jan 1, 2003

By Javier Baladron, Mijail Villar, Brandt Henriksson

"In this presentation an overview will be given of what has been observed by the authors in the copper concentration industry, with a large diversity of tailing thickeners operating under different conditions, although many of them are located in the same neighborhood. A closer look will be taken at the reported performance from different sites and from different thickener designs, either conventional or high rate, including those that were retrofitted, regardless of the thickener brand. An analysis is also made of the generic correlation of the size of the thickener and the performance in terms of solids loading (or unit area) and % solids. The paper envisions a technology development route, makes a brief analysis of the economic impact of the suggested route and points out the need for development in technologies around tailings thickeners, such as automation, yield stress measurement, slurry pumping and construction methods."

Jan 1, 2014

By Raquel Franco de Souza Lima, Isao Matsuoka

"Microflotation studies and abstraction experiments were conducted with synthetic oxide spinels relating to chromite (MgCr2O4, FeCr2O4, FeFe2O4 and FeAl2O4), using sodium oleate as collector. An attempt was done to correlate this data with the speciation of oleate in the bulk solution and at the interface solid-water, to explain the floatability curves. The microflotation tests were conducted using a microflotation cell. The abstraction of sodium oleate was measured at 25°C, with one gram of synthetic spinel and the abstraction time was 30 minutes. After centrifuging, the residual oleate concentration in the supernatant was measured by using the spectrophotometric method described by Mizuniwa et al. (1977), that covers the range from 1.5 to 9 ppm. To cover the range from 0.2 to 1.5 ppm, the residual oleate concentration was measured using the spectrophotometric method described by Gregory (1966). The amount of oleate abstracted was calculated from the difference between initial and residual (equilibrium) concentrations.Figure 1 shows the floatability of FeCr2O4, FeAl2O4, FeFe2O4, MgCr2O4 as a function of pH and sodium oleate concentration of 1 x 10-5 M. The IEP of each sample is indicated in the figure by a vertical line in the horizontal axis. The chromium-bearing spinels FeCr2O4 and MgCr2O4 show the lowest isoelectric points (IEP), around pH 6, while in the case of FeFe2O4 and FeAl2O4, the isoelectric points lie at pH 6.5 and 7.3, respectively. It is seen that the flotation-pH curve for FeFe2O4 has a peak at the pH of the IEP, while flotation peak for FeCr2O4 appears at pH below the IEP and that of MgCr2O4 does at pH above the PZC. On the other hand, FeAl2O4 is floated at pH range between about 4 and 7,3 (IEP). This suggests that the pH value at which the maximum flotation occurs is dependent on the sort of spinel to be floated, though it appears in the vicinity of the respective IEP."

Jan 1, 2003

By Aubrey Mainza, Malcolm S. Powell

"A hydrocyclone with two vortex finders, named the three-product cyclone (3PC), has been successfully tested in the Platinum industry for dealing with the dense Chromite found in UG2 ores. This dense component preferentially reports to the cyclone underflow, resulting in an over-ground fine Chromite component in the final product. The dense media effect caused by a high concentration of this in the cyclone feed produces a coarsening of the cyclone overflow, which results in loss of recovery through over-size silica in the PGM carrying component material in the float feed. The fine barren particles of Chromite that report to the overflow are recovered through entrainment in the flotation process, resulting in detrimental contamination of the slag produced from the concentrate.Data from many industrial scale tests of the 3PC have shown that three distinct products are obtained when the inner vortex finder length (LIVF) is extended to the region either above (normal classification) or below (reverse classification) the transition zone (a region were the inner and outer overflow streams are identical). Due to wear problems arising from extending the IVF deep into the cone of the cyclone, it is advantageous to use the shorter IVF. Only the normal classification results are reported here, but similar outcomes (to opposite overflow streams) were obtained for the reverse classification. The results showed notable differences in the percentage split of the plus 100µm material in the product streams, confirming that three distinct products are discharged from the 3PC. About 12% of the plus 100µm material in the feed reports to the middlings stream, 1% reports to the final product, and the remainder to the cyclone underflow.Results of silica and chrome splits to the three distinct products namely, the inner overflow (INO), the outer overflow (OUO) and the underflow (U/F) are given in Table 1. These show that the 3PC can be used to recover coarse silica through screening the middlings product - which has a high silica content. When the vortex finder ratios (ratio’s of cross-sectional areas) are carefully selected, the split of plus 100µm silica to the middlings product ranged from 2.9 to 9.6%. Large amounts of oversize silica and chrome report to cyclone underflow, explaining their high percentages in the underflow stream."

Jan 1, 2003

By S. Banisi, A. R. Ghasemi, M. Maleki-Moghaddam

Direct observation of the charge shape and its motion in industrial mills are not possible, it is then customary to use transparent end, small-scale mills (i.e., model mills) to determine the charge trajectory directly by visualization methods. Because of a short length of the model mills, the end-wall effects could introduce a significant bias on the observed charge trajectories and shape. The shorter the mill, the stronger the bias. This could be due to some material bridging between the end walls. In this research, the end-wall effects were investigated by gradually increasing the model mill length and analysing the charge trajectory and shape variation at a given operating conditions (i.e., ball filling, mill speed, liner type). The unbiased mill length was assumed to be beyond the mill length where no significant change observed in the charge trajectory and shape. For all tests, the torque of the charge was also measured by a torque sensor. The special design of the model mill with the diameter of 100 cm made possible to increase the mill length in steps of 3.6 cm up to 21.6 cm. Four types of liners, five steel ball fillings (10, 15, 20, 25, 30% v/v) and three mill speeds (55, 70, 85% of critical speed) were tested. The ball sizes ranged from 4 to 12 mm. The results indicated that when the mill length was below 10.8 cm the end walls prevented the charge from free falling. This resulted in lower impact point angles and lower power draws compared with the case of no end-wall effects. When the same experiments were performed using an iron ore instead of balls with the same size range, the impact of end-wall effects was more pronounced. For an increase of 30% in the speed (from 55 to 85%), the torque due the change in the charge shape decreased by 41% (from 3.7 to 2.2 kgf.m) when mill filling was 30%. At the same operating conditions when steel balls used the torque decreased only by 19% (from 9 to 7.2 kgf.m). This was expected due to irregular shapes of the ore particles which facilitated bridging. Three-dimensional DEM simulations also resulted in the similar conclusions.

Jan 1, 2014

By Derek Caizergues, Hurman Eric

Experiments have been conducted at around 1700°C to determine the possibility of carbothermic reduction of alumina under the presence of a metallic solvent. Total pressure of the system was reduced to around 30kPa and metallic nickel, iron, copper and tin were selected as the solvent. The highest recovery of aluminium was achieved with the nickel solvent followed by iron, copper and tin. This ranking for the first three was also in accord with the extent of negative deviation form ideality in the respective binary solutions of these solvents with aluminium. The tin-aluminium system displays positive deviation form ideality. The rate and extent of reduction was found to be highly dependent on temperature and pressure. The pseudo first order reaction rate was found to be applicable to the process in all the solvents used. Rate constants were calculated and it is also suggested that the reduction was controlled primarily by the chemical reaction rate.

Jan 1, 2003

By K. W. Stöckelhuber, A. Wenger, H. J. Schulze

"An important elementary step of the flotation process is the forming, drainage and rupture of a thin intervening liquid film between bubble and mineral particle.After the encounter of the bubble with the solid surface a wetting film is formed. The initial thinning of this film is driven by the capillary pressure inside the bubble. When the film has reached a certain thickness rupture can take place. There are two possible mechanisms describing this process:(a) Gas nucleation, caused by nano bubbles inside the film.(b) Growing fluctuation waves (spinodal dewetting) on fluid interfaces under the influence of any kind of attractive forces (electrostatic, van der Waals).Metastable wetting films on negatively charged, hydrophobic glass surfaces (gaseous phase methylated), or on hydrophilic, positively charged glass surfaces (with Al3+ ions), have been analysed by means of the kinetics of film thinning according to the Reynolds law. These experiments demonstrate that both mechanisms can be responsible for the rupture of a thin wetting film."

Jan 1, 2003

By Graeme Heyes, Warren J. Bruckard, Michael A. Somerville

"Over the past few years CSIRO Minerals has been conducting research aimed at developing a continuous copper converting process to replace the traditional two-stage batch process that is currently used to produce blister copper. Sirosmelt type reactors and calcium-ferrite (lime-based) slags have been used rather than the conventional iron silicate slags. The research work has now been extended to focus on the development of a single-stage continuous copper making process (so-called direct copper converting) in which copper concentrates are converted to low-sulfur blister copper in a single step, that is the smelting and converting steps occur in one continuous stage.One feature of the direct copper converting process is that copper losses to the slag phase can be high, meaning the slag produced needs to be treated to recover the copper value. The feasibility of the whole copper making process will most likely depend on the efficiency and cost effectiveness of the copper recovery stage. Flotation has been identified as the most economical option to recover the copper from direct copper converting slags where it has been estimated that a copper recovery from the slag of above 90% is required to make the overall single stage copper making process economically feasible.A limited series of laboratory batch flotation tests was conducted on a suite of calcium-ferrite-based slags made in laboratory smelting trials. Copper sulfide concentrates from MIM were used as feed-stocks. The objectives of this work were to develop a robust flotation process to maximise the copper recovery and iron rejection from slags made in the process, and to establish operating conditions for future continuous flotation pilot plant trials.The slags treated included a reduced low copper slag, an oxidised high copper slag composite, and a very reduced low copper self-pulverising slag. The copper content of the slags varied from 2.9% to 14% Cu and the CaO/Fe ratio varied between 0.30 and 0.54. In general, the higher the copper content the more oxidised the slag. The copper was present as metallic copper, oxide copper and copper-calcium ferrite phases with the phase mix related to smelting conditions. The slags were crushed, ground, wet-screened at 355 or 210 µm to remove coarse metallic particles of copper, and floated at natural pH (about pH 11) using reagents and conditions appropriate for the selective recovery of the copper phases. Reagent additions were typically 200 g/t KEX and 500 g/t Na2S.9H2O and the grind size was generally a P80 of about 40 µm."

Jan 1, 2003

By Aubrey Mainza, Malcolm S. Powell

"A hydrocyclone with two vortex finders, named the three-product cyclone, has been successfully tested in the Platinum industry for dealing with the dense chromite found in UG2 ores. This dense component preferentially reports to the cyclone underflow, resulting in an over-ground fine chromite component in the final product. The dense media effect caused by a high chromite concentration in the cyclone feed produces a coarsening of the cyclone overflow, which results in loss of recovery through over-size material in the float feed. The fine barren particles of chromite that report to the overflow are recovered through entrainment in the flotation process, resulting in detrimental contamination of the slag produced from the concentrate.With the three-product cyclone a middlings product has been extracted that has a higher concentration of fine chromite. This volumetric stream flow represents a small percentage of the total cyclone feed and it is thus possible to treat it separately via fine screening to remove the fine chromite from the system and recover coarse silica."

Jan 1, 2003

By João Queiroz, Cristian Marquez-Sarmiento, Luiz Teixeira

The removal of various metals from process waters and effluents is usually done by precipitation of the corresponding hydroxide. Manganese however is one metal that does not respond efficiently to that approach. It may be seen in its eH X pH diagram that the way of oxidation to Mn IV rather than hydrolytic precipitation of the Mn II ion as its hydroxide, is the way to efficient precipitation of Mn in the pH range 6 to 10. We studied the use of oxidants O2; NaClO; H2O2; Caro´s Acid (H2SO5) and the combinations of O2 or H2O2 with Na2S2O5, and H2O2 with NaClO, for the oxidative precipitation of Mn from synthetic solutions starting with 10 mg/L Mn, at 25 oC. In adequate conditions, which include pH > 8, it is possible to reach final [Mn] less than 0.1 mg/L in 60 minutes of reaction time.

Jan 1, 2014

By Sergey Gudkov, Yuri Yemelianov, Stanislav Balikov, Andrey Boldyrev, Andrey Bogorodsky

"The results of POX of refractory gold-bearing concentrates using halide-ion as a lixiviant for precious metals and activated carbon as an adsorbent are given. It was found that gold did not recover to the solution when halide was added during POX. Silver partially dissolved in the solution. When halide-based reagents and activated carbon were added during POX, gold dissolved and loaded onto the activated carbon. The degree of sulfides oxidation was 99.3-99.6%. The recovery of gold onto granulated carbon was 94.7-94.8% when using chlorine-bearing lixiviants: NaCL, CaCL and carnalite and 98-99% when using KJ and KBr. This treatment process of refractory gold-bearing concentrates combines sulfide oxidation, dissolution and adsorption of precious metals. The results of the metals recovery achieved using this process can be compared with the recovery during POX-cyanidation. In this case, sodium cyanide was not used. This allows the reduction of capital and operational costs due to the absence of cyanidation, CIL and detoxification of leaching tailings circuits."

Jan 1, 2014

By Francisco Vicuña, Miguel Becerra, Nelson Iglesias

"The following article presents the development of a dynamic tool for the estimation of Jb/Jc rate (ball filling level / total load filling level) of a SAG mil operating in a single stage mode. Using the methodology detailed in this article, it is now possible to have a dynamic estimation tool in the operation, which enables strategic decision making and achieving a continuous development in process optimization. The estimating of the load filling level (Jc) was conducted using a power model, which in this case corresponds to the C-Model developed by (Morrell, 1993) that was calibrated by measuring the load filling levels (Jc) and balls (Jb) using the FARO laser scanning technology by means of Grind-Out and Crash-Stop procedures during the year 2013 and 2014. Finally, to estimate the dynamic filling level of full charge, Jc, three independent models were developed that allowed to feed the adjusted power model: •,SAG mill discharge grate slot wear model •,SAG mill internal volume wear model •,Ball filling level estimation model."

Jan 1, 2014

By P. Hatefi, O. Rahmani, M. Noor-Mohammadi, A. Tohry

"Depressants play an important role in the selective separation of impurities from iron minerals by direct or inverse flotation. In this paper, sodium co-silicate (SCS) with chemical formula of Na4SiCO6, as a depressant with pH modifier features, has been synthesized and used for phosphorus bearing iron ore in anionic reverse flotation. In this process, phosphorus is floated while the iron oxides are depressed, using fatty acids as collector in an alkaline medium. Batch and pilot flotation tests were carried out to investigate the influence of SCS on the separation selectivity of phosphorus from iron oxides. Also the depression mechanism of SCS on hematite surface was investigated by microflotation tests and FTIR spectroscopy measurements. The flotation results indicated that without using a pH modifier, the pH of pulp could reach up to 10, when SCS was used as depressant. In this condition, a better depression performance was observed compared to sodium silicate (SS). Using the SCS, phosphorus and total iron content in iron concentrate was 0.046% and 66.29%, respectively, compared to SS where these values were 0.06% and 65.75%, respectively. As a result the weight recovery of iron concentrate was increase by around 4%, compare to SS. It was also found that 238 g/t of SCS could be used instead of 3 types of reagents collectively, including 32 g/t of NaOH, 151 g/t of Na2CO3 and 400 g/t of SS gel.INTRODUCTIONThe phosphorous presents in iron ore minerals is mainly in the form apatite mineral. The apatite is separated from iron ore minerals by magnetic and flotation methods (Ma, 2012). The reverse anionic flotation of iron is one of the most common method for removing phosphorus from iron concentrate (Araujo et al., 2005).Usually apatite minerals are readily floated using anionic collectors such as fatty acids (Ma, 2012). In this conditions the iron minerals are depressed and by modifying the pH in alkaline conditions, selective separation of phosphorus from iron concentrate can be achieved. Depressants including; sodium silicate (SS), starch, dextrin, guar gum and humic acids play an important role in the reverse flotation of iron ore (Kar et al., 2013; Ma, 2012; Turrer and Peres, 2010; Araujo et al., 2005). Studies have shown that SS has a better effect on iron recovery and phosphorous reduction, compared with other depressants (Tohry and Dehghani, 2016; Qi et al., 1992, Dho and Iwasaki, 1990). In most flotation processes, modifiers are used to adjust the pH. To achieve alkaline conditions, mainly pH modifiers such as carbon dioxide and sodium carbonate are used."

Jan 1, 2018

By M. L. Torem, R. H. Rojas, A. G. Merma

"Fine particle recovery by conventional flotation processes is very low mainly due to the low probability of bubble/particle collision and adhesion. In order to solve the problem of low particle recovery, several flotation technologies have been developed to increase bubble/particle collision efficiency. Among these technologies, the electroflotation process stands out. This process has advantages in the generation of microbubbles (<100 µm) and in the production of different amounts of hydrogen and oxygen microbubbles. These advantages favorably influence the fine particle floatability, due to the greater probability of particle/bubble collision and adhesion. The electroflotation tests were conducted for a hematite/sodium oleate system in a Partridge-Smith modified electroflotation binary cell of 0.38 L usable volume. The sodium oleate concentration, particle size, pH and current density were evaluated. Satisfactory results in the recovery of hematite were found at pH values of 7, reaching hematite floatability of 99% and 90% with hydrogen and oxygen bubbles, respectively.INTRODUCTIONThe flotation recovery of fine and ultrafine particles is normally very low and is caused by several factors, among them, the low probability of collision and adhesion bubble-particle, the difficulty to overcome the energy barrier (entrainment and entrapment), low selectivity, surface oxidation and mineralogical changes (Schulze et al., 1989; Waters et al., 2008; Shahbazi et al., 2010). This problem can be overcome by decreasing the bubble size or by increasing the apparent particle size. However, it is worth noting that the use of small bubbles or micro bubbles also involves some disadvantages such as their low momentum resulting in a slower process comparing with conventional flotation. Electroflotation is an attractive alternative for treating fine particles with small bubbles less than 100 µm, generated by the electrolysis of water. Electroflotation is one of the variants of the flotation process, where the gaseous phase is produced by electrolysis of an aqueous solution, generating oxygen and hydrogen bubbles (Sarkar, 2010; Gupta and Ali, 2012). These smaller size bubbles allow the recovery of fine particles by increasing the collision efficiency. This process is versatile and competitive in relation to other techniques such as dissolved air flotation and dispersed air flotation because the electroflotation units are smaller, more compact and require less maintenance and less operating cost than other flotation units (Zouboulis and Matis, 1995,). In addition, the electroflotation process is a clean technique and provides results in a short time, requiring only the investment in the electroflotation cell construction stage and the choice of the electrodes (Ketkar et al., 1991; Sarkar et al., 2010; Sun et al., 2011). In this sense, this study assesses the effect of pH, particle size and sodium oleate concentration on electroflotation of hematite fines."

Jan 1, 2018

By H. Pearce, A. E. Lewis, A. Ochieng

"Hydrodynamics and mixing are fundamental to the operation of mineral process systems such as flotation cells and metal precipitation reactors. Hydrodynamic conditions influence phase mixing and mass transfer in a multiphase system, and these affect the overall performance of such a system. Detailed information on the effects of the hydrodynamics on the performance of agitated systems is still required for the design and optimal operation of hydrometallurgical systems, which are always multiphase. Computational fluid dynamics (CFD) techniques have been employed to study the hydrodynamics and mixing, most of which have focussed on the performance of axial and radial pumping impellers in agitated tanks. However, very little has been reported on the influence of a draft tube on the flow profile in such systems.CFD simulation of a stirred vessel centres on the way the impeller is modelled. Some of the most recent approaches to modelling an impeller are impeller boundary condition (IBC), snap shot, sliding grid (SG), multiple frame of reference (MFR) and inner outer (IO). The accuracy, with which these models predict experimental results and the corresponding computational demands, form the basis upon which the choice of an approach is made. Most of these approaches (IO, SG and MFR) address the key problem of the stirred tank modelling, namely, the simultaneous meshing of the rotating impellers and the stationary baffles. The MFR is computationally cheap and has been found to give predictions that compare well with experimental data.The CFD technique (code CFX4.4) has been employed in the present work to study the hydrodynamics in a mixing vessel stirred with either a Rushton turbine or a pitched blade impeller. The multiple frame of reference (MFR) approach has been used to model both impellers. A draft tube was used only in the Rushton turbine stirred vessel. The flow profiles for the impellers have been studied in three regions; below the impeller tip, at the middle of the tank, and near the liquid surface. The simulation results were compared with literature data obtained using a laser Doppler velocimetry in the three regions of the vessel, and it was found that the model predictions were better in the impeller region. There was a poor prediction of the experimental results in the region closer to the liquid surface; however, this was improved when the turbulence parameter (C2) in the k-e model was set to a higher value. The value of the impeller clearance at which the Rushton turbine generates an axial impeller type flow has been determined and it has been shown that, at this clearance, a draft tube can be used to enhance axial flow in a Rushton turbine stirred reactor."

Jan 1, 2003

By Gus Van Weert, Samuel A. Bolorunduro, David B. Dreisingerm

"As deposits of high-grade base metal sulphides become depleted, attention must be focused on the treatment of complex sulphides, which contain significant fractions of precious metals such as gold and silver. Acid pressure oxidation is a promising process for these materials and the recovery of silver and gold will improve the economy of the process. Gold can be recovered from the oxidised residues, however, silver is incorporated into the jarosite specie and the cyanidation of the resulting residue yields very low recovery.Pressure oxidation of various complex sulphides was carried out at 110-150°C in sulphate media with additions of potassium iodide under conditions similar to industrial autoclaving. The resulting residues were subjected to cyanidation. High recovery of silver, up to 98%, was achieved because its incorporation into lead-hydronium jarosite during the pressure oxidation was minimised, while its deportment into the cyanide-soluble silver iodide was favoured. Silver recovery decreased slightly at high temperatures (140° and 150°C) because of the enhanced stability and kinetics of lead-hydronium jarosite, but this could be overcome by increasing acidity and iodide concentration of the autoclave slurry."

Jan 1, 2003