Search Documents

By Derek Caizergues, Hurman Eric

The principle of carbothermic reduction has been around for many years. In principle it is a simple process, yet with a multitude of problems. The temperature required to affect reduction is in the region of 2200ºC and results in aluminium oxy-carbide formation rather than metallic aluminium. From a thermodynamic point of view, reducing the temperatures of reaction which would suppress oxy-carbide formation would only be possible by lowering the total pressure of the system. A decrease in thermodynamic activity of product aluminium by dissolving it in another phase would also help preventing the formation of oxy-carbides and would also increase the yield of the reduction reaction. Thus experiments have been conducted at around 1700ºC to determine the possibility of carbothermic reduction of alumina under the presence of a metallic solvent. Total pressure of the system was reduced to around 30kPa and metallic nickel, iron, copper and tin were selected as the solvent. The highest recovery of aluminium was achieved with the nickel solvent followed by iron, copper and tin. This ranking for the first three was also in accord with the extent of negative deviation form ideality in the respective binary solutions of these solvents with aluminium. The tin-aluminium system displays positive deviation form ideality. The rate and extent of reduction was found to be highly dependent on temperature and pressure. The pseudo first order reaction rate was found to be applicable to the process in all the solvents used. Rate constants were calculated and it is also suggested that the reduction was controlled primarily by the chemical reaction rate.

Jan 1, 2003

By V. G. Prikhodko, G. I. Sukhinin, I. V. Yarygin, A. V. Fedoseev, S. A. Novopashin

"The first experiments on the vacuum drying of spherical clay sample are presented and the theoretical model of the process is considered. The model is based on the solution of the heat and the moisture transfer equations with the effective thermal conductivity and water diffusion coefficients for wet porous clay-like medium. The time and radial dependence of the temperature and the moisture were calculated for different initial conditions. The results obtained for the time dependence of the moisture content are in good agreement with the experimental results obtained in the initial period, when all the moisture in the sample did not freeze to form an ice crust. INTRODUCTION Capillary-porous materials very often occur in nature and in industry. A porous medium is a solid matrix with voids, or pores, which are continuously connected. These pores are usually filled with fluids or moisture, water vapor and air that can pass through the medium because the voids are interconnected. The void fraction in the solid matrix is referred to as the porosity. Porosity or void fraction is a measure of the void (i.e. ""empty"") spaces in a material, and is a fraction of the volume of voids over the total volume. The moisture content in porous media determines the properties of the porous body, its mechanical and thermo-physical properties, such as density, plasticity, viscoelasticity, swelling, cracking, and so on. Complex processes of heat and mass transfer occur in porous bodies when they are heated or cooled, during drying or freezing (Luikov,1966). The course of these processes depends essentially on the physical-chemical composition of the solid matrix of the porous body, on its fractal dimension, porosity and morphology. The clay and clay minerals are the most important porous materials in the history of the mankind (Mukherjee, 2013). Clay is a very fine grained, unconsolidated rock matter, which is plastic when wet, but becomes hard and stony when heated. It has its origin in natural processes, mostly complex weathering, transported and deposited by sedimentation within geological periods. Clay is composed of silica {SiO2), Alumina (Al2O3) and water (H2O) plus appreciable concentrations of oxides of iron, alkali and alkaline earth, and contains groups of crystalline substances such as quartz, feldspar, and mica. Building materials, bricks, and tiles, pottery, porcelain and faience are made from clay. Clay is used in the food and medical industry, and, not least, in the mining industry as a carrier containing aluminum, silicon and other valuable elements, as well as metals (copper, gold) as constituents, contained in the pores in the form of micro- and nano-particles or grains."

Jan 1, 2018

By M. Brennan, A. Majumder

"The mineral processing research community has devoted enormous efforts to the modelling of mineral separators over the last 50 years. While many efforts have been made to use only fundamental physics as a basis for the models, fluid flow patterns in separators are not simple while the motion of particle swarms through fluids is extremely complex.Sluices are the simplest forms of the flowing film concentrators and have been used in the mineral industry since at least the 15th century (Agricola, 1556). Flowing film concentrators, in general, still have widespread applications in the mineral industry and their designs vary according to the specific need.Particle separation in a sluice appears deceptively simple, but the separation mechanism has proven complex and difficult to quantify. Separation in the sluice takes place in a flowing film a few millimetres thick. The particles are suspended by turbulent eddies and motion relative to the fluid takes place in socalled hindered settling mode. The difficulty arises because the presence of the particles influences the flow pattern and when the particles are fully transported by the flow, the flowing slurry may not have the same viscosity as water and does not have the same density. For this reason a universal theory which can explain the behaviour of a suspension in a sluice or any other gravity equipment has still not been developed. Few attempts have been made to analyse the mechanisms involved in the concentrating processes of pinched sluices and Reichert cones.Fluid flow behaviour and slurry transportation characteristics in open channels have, however, been active research topics in the disciplines of fluid mechanics, chemical engineering and civil engineering for many years. As a result, an extensive literature is available, which has led to the development of the model described in this paper.In an effort to test the extent to which fundamental fluid mechanics can provide a prediction of particle separation, a study on a simple parallel-sided sluice has been carried out using glass beads at various particle concentrations and flow rates, and the actual particle separation taking place compared to predictions from modelling.The modelling strategy was divided into two parts; the first was to predict the horizontal slurry flow velocity profile and the second to predict the solid particle concentration over the depth of the flow at different flow conditions. The predictions were then validated with measured data sets. This can easily be done if the slurry flow is split at different fractional flow depths so that the mass flow of solids over different flow heights is measured accurately over a fixed period. Mass flow splits can then be calculated by integrating the product of the predicted slurry velocity profile and the predicted solids concentration profiles from the base of the sluice bed to the slurry free surface."

Jan 1, 2003

By Thomas Pretz, Alexandra Pehlken

Sampling of municipal solid waste is known to be difficult to sample if it has to be representative. When dealing with municipal solid waste, the usual method is to study separately waste material below 40 mm and particles bigger than 40 mm. The material < 40 mm cannot be sorted manual and is termed the “fine fraction”. The particles > 40 mm can be separated manually and are usually sorted into pre-defined groups of materials. These groups can be defined depending on the demand of quality assurance. But standardisation of procedures is not far progressed, even for the widely practised sorting methods.

Jan 1, 2003

By Majid Saghaeian, Rasool Hejazi, Parisa Ghobadi

"Pulp handling in mineral processing circuits is very complicated due to its inherent different specifications compared with other fluids such as water. Because any variation in ore property (e.g. size and abrasion index) and pulp specification (e.g. density, solid content and pressure) causes problem in this part and reduces the plant availability and throughput as a result. The most common issues in the hose system are sumps and pipe-line blockage, wearing of the pumps impeller and liner, and pipe tearing specially at elbows and bends. High pressure grinding roll (HPGR) is employed in a closed circuit with a screen as the first stage of grinding in Zarand Iranian Steel Complex (ZISCO). Wearing of the pump and pipeline transferring the screen undersize stream was the main problem from the plant commissioning. The plant couldn&apos;t achieve to the design capacity because of this defect. Although various practical solutions such as improving the pipes and impeller material quality and eliminating the elbows, as much as possible, were done in order to downtime minimizing, but damages didn’t vanish. Since HPGR discharge contains somewhat rough and abrasive particles, the mentioned modifications didn&apos;t effective very much. Therefore, converting of the wet screen to dry and using of belt conveyor to the screen undersize handling was employed based on the plant capability evaluation and experimental and pilot trial results. Although this reformation imposed another additional cost (for conveyor system), but it had significant advantages such as increasing the plant availability up to 96%, reducing the operating costs of the wear parts, providing more stable operating condition for the HPGR performance and decreasing abrasion rate of the HPGR rolls liner because of the lower moist feed."

Jan 1, 2014

By Lei Zhang, Xianjun Lu1, Minjie Lian, Liyang Zheng

In order to investigate rheological behaviour of fine tailings backfill pastes, the fine iron ore tailings (size fraction of -0.074mm accounts for 70%) from Fuquan Mining Co., Ltd. of Sinosteel Corporation (Shandong, China) was investigated. The rheological parameters such as slump, viscosity and yield stress of the tailings pastes under different densities were measured in detail, and the effect of paste density on the rheological property and the relationships of different rheological parameters of the pastes were also discussed. According to the results, the rheological behaviour is in accordance with the pseudoplastic fluid in a wide range of paste densities (solid content, w/w) of 65% to 80% and the pastes turn to be Bingham fluids at higher shearing rates. Along with the increase of paste density, the slump drops gradually and the viscosity and shear stress increase gradually. However, the variation extent of the rheological parameters varies at different density ranges. According to the variation pattern of the rheological parameters at different paste densities, the flow ability of the pastes can be classified into three zones. The high fluidity zone was observed at the density range of 65%-69% where the rheological parameters vary slightly along with the paste density, the moderate fluidity zone was observed at the density range of 70%-76% where the rheological parameters vary significantly along with the paste density, and the low fluidity zone was observed at the density range of more than 76% where the rheological parameters vary sharply along with the paste density and the critical density for this sudden variation is about 76%. Furthermore, linear correlations of slump/viscosity and slump/yield stress were observed. It is possible to predict the viscosity and yield stress of the pastes based on the slump measurements.

Jan 1, 2014

By R. Van Hille, A. E. Lewis

"The precipitation of a selection of metals from both a synthetic and an actual metal-rich effluent was investigated. The experimental aspects of this study were carried out in a two-stage process consisting of a pre-treatment clarifier and a fluidised bed (pellet) reactor. Each unit operation in the two-stage process was investigated separately. The pretreatment clarification stage at pH ˜ 5 resulted in a 99.9% removal of iron and 97.3% removal of aluminium.The pellet reactor was used to precipitate nickel as nickel hydroxy-carbonate from a pure stream and a removal efficiency of 99.6% was achieved. The high local supersaturation at the reagent inlet points caused the formation of a large amount of fines, but these agglomerated onto the pellets up the length of the bed (See Figure 1).For copper precipitated as copper sulphide from a pure stream, a maximum removal efficiency of 92% was achieved. The high local supersaturation at the reagent inlets also caused the formation of a large amount of fines, but the extremely sparingly soluble nature of copper sulphide meant that the fines were not agglomerated up the length of the bed. In Figure 2, the global supersaturation ratio was relatively low, and thus there is little homogeneous nucleation and degree of fines formation. However, the fines occurring after the third sulphide input point (at 30cm from the bottom of the bed) indicate that local supersaturation also plays a critical role in fines formation. It was therefore concluded that, for the copper sulphide case, it is essential to control the supersaturation at the inlet points in order to prevent fines formation altogether, as it is not possible to agglomerate the fines once they exist in the bed."

Jan 1, 2003

By R. Van Hille, S. Lacour, A. E. Lewis, K. Peterson

"This paper compares thermodynamic modelling results with those obtained for copper sulphide removal from aqueous solution in both continuous and batch experiments at laboratory scale. Sulphide precipitation has been demonstrated to be an effective method for heavy metal removal. The advantages are the high degree of metal removal at low pH, low quantities of sludge formation, the ease of de-watering and low reactor retention time due to high reactivity of sulphides. However, the low solubility of sulphide species can lead to spontaneous nucleation of fines, which are difficult to remove.Theoretical modelling was carried out using ASPEN Plus™ and OLI systems Inc ESP process. Both simulators were used to calculate copper sulphide recovery and residual aqueous copper concentrations as a function of pH. The predictions were then compared with experimental results. Both simulations predicted that all of the inlet copper would precipitate as sulphide CuS(s) over the entire range of pH and sulphide: copper molar ratios investigated. The simulation results were strongly influenced by the number of chemical species and the nature of the thermodynamic data taken into account in the model.The continuous experimental studies were carried out in a fluidised bed reactor (FBR). Copper sulphate was reacted with sodium sulphide and the solid precipitated directly onto the pellets in the FBR. The use of sulphide was motivated by high sulphate levels in local acid mine drainage and the ultimate integration of the metal removal process with a biological sulphate reducing process that produces an aqueous sulphide stream.A maximum dissolved copper removal of 99.6% (AAS analysis) and a total removal efficiency of 95.8% (dissolved copper minus fines) were achieved. Stoichiometry of the precipitate was determined from SEM/EDAX analysis (atomic percentages) and was close to 1/1, irrespective of the operating conditions."

Jan 1, 2003

By Remmerswaal, U. Boin, M. B. G. Castro

"To design sustainable products that can be recycled with high resource efficiency, low environmental impact and economic feasibility, the choice of materials and materials combinations, made in the design stage, is fundamental. The products we design, manufacture and use now will be the resources of the future. Designers are able to select materials for a product according to the many functional requirements they must fulfil. But they have a limited knowledge of the recycling processes and its requirements regarding quality of the secondary material streams. Resource Engineers have to manage the processing of these streams, that are becoming more complex with the increasing variety of materials and decreasing size of components. After mechanical separation of the materials streams resulting from shredding of EOL (endof- life) products, there is always a degree of contamination, from two possible causes:Incomplete liberation: the bonds between different materials combined in a component are not completely destroyed by shredding, resulting in some particles containing two or more materials attached;Separation efficiency: the mechanical separation processes are not able to separate perfectly the many material particles; there are always a number of foreign particles in the recovered streams.Sometimes, those contaminants cannot be removed by the industrial metallurgic recycling processes, and a more serious problem occurs when the contamination levels compromise the recycling of the material stream by lowering its quality (i.e. the properties of the recycled material will be lower due to the contamination). As a consequence, the material must be diluted in virgin raw material and/or used in a less demanding application (downgrading), causing resource depletion and increased energy use, waste production and recycling costs. In order to make the best choice of materials combinations for a product, a systematic approach is necessary, that can close the gap between the knowledge areas of Product Design and Recycling Technology."

Jan 1, 2003

By Jussi Liipo, Pertti Lamberg

Image analysis of process samples gives precise data on particles and their composition. The results presented as liberation tables and maximum grade-recovery curves are informative and good for comparing different feed materials, but basing on them it is impossible to predict the results of the mineral separation process (flotation, magnetic separation, gravity separation) in details. The exact and extensive particle data has remained large unused, because there has not been a model nor a modeling program to include particle information in mineral separation processes. This study introduces a method, which incorporates the particle data in the kinetic model of flotation. Similar approach can be used in modeling other separation processes, too.

Jan 1, 2003

By Ana C. C. Pacheco, Maurício L. Torem

"The aim of this work was the study of the effect of the type (Fe3+, Al3+ and Fe3+ and Al3+ mixture) and of the coprecipitant concentration on As5+ removal by ACF. Removal of As5+ using sodium dodecyl sulfate (SDS) as a collector was studied by Adsorbing Colloid Flotation (ACF) at laboratory scale. The morphology of the precipitate retained in the foam was analyzed by Scanning Electron Microscopy (SEM/EDS).In order to investigate the effect of the initial concentration of Fe3+ on As removal, sets of experiments were performed with a concentration of Fe3+ in the proper range of pH (5,0 – 6,0) previously observed in the coprecipitation tests. As removal improves significantly as the concentration of the coprecipitant agent increases from 60 mg.L-1 (77,4%) to 80 mg.L-1 (99,7%). This is probably due to the higher concentration of ferric hydroxide (Fe(OH)3) which provides a larger surface area available for adsorption of As. From the initial coprecipitant concentration of 80 mg.L-1, As removal has shown to be rather high (? 99,7%), with the maximum being (99,9%) by using a Fe3+ concentration of 160 mg.L-1. Therefore, for a maximum As removal, under these test conditions, the optimum concentration of Fe3+ is 160mg.L-1.This paper also shows the effect of the initial concentration of Al3+ on As removal at a suitable range of pH (7,0 – 8,0). A very significant increase on As removal was found to occur as the initial concentration of coprecipitant was increased from 60 mg.L-1 (35,7%) to 80 mg.L-1 (97,7%) and a decrease in As floatability (43,7% - 54,5%) was found to occur from that Al3+ concentration amount. Based upon those results, the optimum Al3+ concentration so as to remove As under these test conditions is 80 mg.L-1."

Jan 1, 2003

By M. H. Moys, H. Dong

"Discrete Element Method (DEM) has become a standard tool to simulate grinding mills in order to gain information about load behaviour, power drawn, etc. However, parameters necessary to run a simulation are not always readily available. For example, the coefficient of restitution used in DEM simulation from the literature ranges from 0.1 to 0.9 due to lack of accurate values. The lack of correct input parameters results in the fact that some simulation parameters are adjusted to match the simulation prediction with the experimental results. It is inappropriate to tune one single parameter arbitrarily in order to fit the prediction with experimental results. The correct value of parameters for DEM simulation should be established, and rigorous validation on simulation results by DEM needs to be done.The objectives of the ongoing project are to measure the coefficient of restitution at conditions analogous to grinding practice. Equipment has been built to measure the coefficient of restitution. A typical case of impact test showing the vertical position of a ball as a function of time is presented in Figure 1. The coefficient of restitution between steel ball of different sizes and the targets including steel liner (e = 0.91), mild steel block (e = 0.57) and rubber liner (e = 0.7) have been measured. The coefficient of restitution reduces to 0.38-0.52 when there is a layer of coal particles (1-2 mm) on the steel liner. The effects of ball size, drop height on coefficient of restitution are investigated. Then a DEM code is developed of several contact models to simulate the impact process. This code can reveal details on velocities (translational and rotational) and forces (normal and tangential) during the brief impact interval. Figure 2 is a comparison of the rebound rotational velocity between experiment and prediction by different models. The results can be used as DEM input and to assess contact models."

Jan 1, 2003

By Ashton M. Swartbooi, Robert van Hille, Alison E. Lewis

"Nickel production by precipitation using hydrogen reduction generates an ammonium sulphate solution containing approximately 2g/L of nickel, and 1g/L of cobalt as an impurity of the process. Sulphide precipitation is an effective method for heavy metal removal, especially when compared to hydroxide processes: metals can be removed from solution at relatively low pH levels, small quantities of sludge are formed, and due to the high reactivity of sulphides the reactor retention time is reduced. However, the low solubility of sulphide species can lead to spontaneous nucleation of fines (due to higher supersaturation levels which are difficult to separate from solution, leading to reduced process efficiency. Using a fluidised bed reactor, fines formation can be minimised as the pellets provide a large surface area and promote heterogeneous nucleation.A synthetic nickel-cobalt ammonium sulphate solution was reacted with two forms of sulphide reagent: (a) a liquid sulphide solution and (b) gaseous hydrogen sulphide. A range of factors (including pH, reagent concentrations, metal to sulphide molar ratio, flow rates and recirculation rates) influencing the efficiency of the precipitation reaction have been studied. The efficiency of the precipitation reaction was measured using both metal recovery and fines formation as indicators.Figure 1 shows the effect of decreasing the metal:sulphide ratio (at constant SS = 2.725e+17), on the metal removal for liquid sulphide. By decreasing the metal:sulphide ratio, up to 99% removal of both nickel and cobalt could be achieved.These results also indicate that the precipitates that formed were polysulphides, since no sulphide was present in solution after the experiment. This would also indicate that a lower metal:sulphide ratio would be more favourable. However, decreasing this ratio (at constant metal concentrations) would lead to an increase in the fines concentration, because of increased supersaturation levels induced by the higher sulphide concentrations. To decrease the supersaturation, dilute solutions of either reagent would be employed."

Jan 1, 2003

By Olgac Kangal, Ali Guney, Gulay Bulut, Guven Onal, Ayhan A. Sirkeci

"This paper presents the results of pilot scale column flotation applications in the two different copper concentrators in Turkey. The Kure Copper Plant is located in the Black Sea Region of Turkey. There are four types of copper ore formations in the Küre region. The so called disseminated ore contains 60-70% siliceous minerals of which Cu content is around 0.5%. The remaining three ore types in the region are generally named “massive ores”. The massive ores may assay up to 15% Cu and the major gangue mineral is pyrite associated with relatively little amount of silica. The main copper mineral in all formations is chalcopyrite that is generally finely disseminated in pyrite therefore satisfactory liberation requires ultrafine grinding especially in the case of the massive ores.A blend of these ores, containing 1.7% Cu on average, is fed to the Küre Copper Concentrator whose capacity is 1.2 million tons of ore annually. Unfortunately, today the plant operates below its designed capacity treating around 550,000 tons of ore per year. The design of Küre Copper Plant was undertaken by the Outokumpu Company of Finland. The operation of the plant is almost automatically controlled and the feed, the concentrate and the tailings are assayed for copper by on-line XRF analysers. The particle size analysers are also connected to the grinding circuit. The feed material is ground almost below 50 µm and the flotation is conducted around pH 11.2 using Hostaflot X-231 (a trade mark of Hoechst) as the collector. Apart from the rougher cells, there are four cleaning stages after which the final concentrate is produced. A very fine grinding requirement for an adequate level of liberation makes successful flotation difficult and consequently the final concentrate can hardly assay above 16% Cu leading to copper losses around 20% in the tailings that contains 0.3% copper."

Jan 1, 2003

By J. Yvon, Inna V. Filippova

"The aim of this work is to seek the inhibitors of the meteoric and bacterial dissolution of sulphides and gangue minerals to stop the undesirable chemical reactions during conservation of the flotation wastes. The approach of passivation of surfaces by chemical treatment of the solid phase is applied for this objective.The samples taken from different depths of an old French waste dump revealed the capacity of the flotation tailings to produce acid waters (pH 1.8-2.4) and to release heavy metals. Mineralogical studies show not only the product of sulphide oxidation, i.e. sulphates, but also the complex transformations of aluminosilicates in acidic liquid phase. The detection by XRD of aluminium hydroxides (gibbsite, boehmite) allows supposing the recrystallisation phenomena during tailings conservation.Comparative tests of the passivation of the surface of sulphide minerals and waste of flotation with using of conventional reagents (CaO, NaOH, phosphates) and original reagents for this purpose (alkyl dithiocarbamates) allow to identify the optimal treatment conditions and the efficient chemicals.Leach tests were carried out in percolation columns during 68 weeks. The normalised leaching tests according to French legislation were run to confirm the selected treatment conditions. The results obtained show that a single treatment with carbamate inhibits the oxidation of the pyrite and the other sulphides, and totally prevents the formation of acid waters (the stabilised pH was 5.3-5.8). Treatment of in situ drainage water allows to obtaining a total precipitation of heavy metals: the residual concentrations of Fe, Cu and Zn are lower than 0,1 mg/l.The passivation of sulphides is the result of the formation with carbamate (studied by IR spectroscopy and XPS) of organometallic compounds, which are stable in acid medium. The presence of thiuramdisulphide (product of alkylcarbamate oxidation) at the mineral surface stabilises the mixed adsorption layer and leads to a considerable reduction in the hydratation rate of surface by avoiding the corrosion of the pyrite. No aluminium was detected in leach solution with this treatment."

Jan 1, 2003

By Nicolus Rotich, Ritva Tuunila, Louhi-Kultanen. Marjatta

Most minerals, their ores, and gangue require sorting in order to maximize the recovery of the primary product during concentration. Gravity separation though old, is not obsolete and is continually playing an important role in mineral processing and many other industries, especially where plant energy efficiency is of concern. Screen designs e.g. material of construction, deck angle of inclination, the feed throughput, and physical as well as chemical properties of the particles, are critical factors to consider when using gravity for solid separation. Solids loading and screen geometry are significant, and easily manipulated operational parameters that affect both the screening rate and efficiency to a large extent. In this paper we applied nonlinear least squares optimization technique, and response surface methodology first, to assess the significance of the two factors, and secondly to select the best mathematical models that optimize both capacity and efficiency of the screening process. Initial experiments and confirmation tests were conducted on a prototype screen of 846.51cm2 effective area, (2100 cm2 total area). For glass beads of sizes 0.75-3mm, with feed loads of 10g up to 160g, and inclination angles from 5-20o, a maximum efficiency of 66.7%, and a screening rate of 22g/s was achieved with a screen loading of 86.5g, and an inclination angle of 12.43o. These results were then subjected to nonlinear least squares optimization, in which afterwards an optimum theoretical efficiency of 72% and screening rate of 31.2g/s were achieved at a loading of up to 104g. There was excellent performance at angles 12.5=?=17.5, but poor at the angles outside this range. The screening efficiency did not seem to respond significantly to changes in screen loading. Confirmation tests conducted at selected optimum parameters achieved an efficiency of 72.1% (at 17.5o with 88g load), and a rate of 27g/s at 16.5o with 104g.

Jan 1, 2014

By R. Peter King, Claudio L. Schneider, Reiner Neumann

Predicting the liberation spectra that is produced from breakage of two-phase ores under the random fracture assumption can be accomplished by measuring the conditional, on length, linear grade distribution directly from images obtained from a representative sample of the unbroken texture. The technique tremendously simplifies the prediction problem by avoiding the multiple convolutions that arise from the traditional method based on a description of texture from a measurement of the chord length distributions associated with each phase in the unbroken texture. For a 3-phase system, the phase transition probabilities associated with the textural information make the traditional calculation an almost insurmountable mathematical problem. The direct measurement procedure on the other hand can be expanded to three phases comparatively easily.

Jan 1, 2003

By M. Canbazoglu

In this study, optimum sulphuric acid leaching parameters of zinc and other valuable metals from two different waelz clinker samples were researched. Origins of the samples are electric arc furnace dust and original non-sulphite zinc ore waelz clinkers. The main zinc mineral determined as zincite in these samples. Collective dissolution of zinc and other valuable metals in waelz clinkers can easily achieved by sulphuric acid leaching of them. 96% of zinc can be dissolved at 80 ºC, 60 g/L sulphuric acid concentration, 60 min. leaching time and 1/5 solid/liquid ratio. Almost 90% of Cd, Cu and Co in clinker dissolved at these conditions while dissolution of Fe was almost 20%. The consumed acid amount for dissolved per ton of zinc is approximately 1.7 tons at these conditions.

Jan 1, 2014

By F. S. Hoseinian, K. Filho, D. Deglon, T. Souza, M. Safari

"This paper investigates the reverse flotation of hematite in three laboratory flotation cells with very different contacting environments. The main objectives are to investigate the recovery of coarse quartz by flotation and fine hematite by entrainment. The laboratory flotation cells used were the mechanical, oscillating grid and pneumatic cells. The effect of froth height and solid concentration were investigated in the mechanical and pneumatic cells. The effect of impeller speed and energy input were investigated in the mechanical and oscillating grid cells. Froth height results show that coarse quartz particle recovery decreases almost linearly with increasing froth height due to increased detachment of coarse quartz particles in the froth. Fine hematite particle recovery also decreases almost linearly with increasing froth height due to decreased water recovery and associated entrainment. Agitation/energy input results show that coarse quartz particle recovery increases with increasing impeller speed to an optimum, after which this decreases dramatically. The increase is due to improved gas dispersion, generation of smaller bubbles and increased bubble-particle collision and attachment. The decrease is due to significantly increased bubble-particle detachment at higher impeller speeds. The recovery of coarse quartz particles in the OGC is higher than that in the mechanical cell with an optimum at a much lower energy input. Solids concentration results show that both mass recovery and water recovery increase with increasing solid concentrations. The pneumatic cell achieves higher mass recoveries and lower water recoveries than those in the mechanical cell at equivalent solids concentrations and operating conditions. INTRODUCTIONFlotation is a selective process for separating different minerals from each other. The flotation separation efficiency depends on the recoveries of the mineral species by both true flotation and entrainment (Neethling and Cilliers 2009; Wang et al. 2015). Both chemical variables and hydrodynamic conditions within the flotation cell affect the recovery and selectivity of the flotation process. Cationic reverse flotation of hematite is a common method for selective separation of quartz from iron ores to produce pellet feed. The presence of coarse quartz particles in the tailings and fine hematite particles in the concentrate are two major challenges in the reverse flotation of hematite (Vieira and Peres 2007)."

Jan 1, 2018

By O. N. Mohanty, S. Mohan Rao, N. D. Rao, T. Mukherjee, P. V. T. Rao

"Chromite ore is an indispensable raw material in the manufacture of ferro-chrome and charge-chrome, which are used for the production of stainless and other alloy steels. The demand for chromite ore is ever increasing because of increasing consumption of these steels. Keeping this in view, Tata Steel is keen to recover values from fines and wastes, and also to produce value added products from their captive chromite mines and its processing plants.Tata Steel has its captive chromite resources at Sukinda, Orissa. They contain two ore types, i.e. (i) Ferruginous and (ii) Siliceous. The generation of off-grade ores is an increasing trend and simultaneously customer quality requirements are becoming ever more stringent. The ferruginous type ore also contains a considerable quantity of in-situ fines (~20% particles below 0.5 mm) that compound the beneficiation problem.In many places, in India and abroad, mined non-marketable off-grade and low grade chromite ores are upgraded by using either simple classification techniques like screw classification, hydrosizing, hydrocycloning or conventional gravity concentration processes such as Heavy media separation, Jigging, Spiraling, Tabling etc.At Tata Steel, the ferruginous type ores are treated in Chrome Ore Beneficiation (COB) Plant that comprises: a crushing and grinding circuit; a classification circuit using hydrocyclones; and a beneficiation circuit using 4 stage spirals in the coarse circuit (-0.5+0.1 mm) and 3 stage spirals & tables in the fine circuit (-0.1+0.038 mm). In this process, 3 types of tailings are being generated and together analyses about 17 % Cr2O3, which is high. From the present operation the chromite recovery is around 70% and could not produce coarse concentrates (+0.5 mm size). Whereas the siliceous type ore is treated in the Lumpy Ore Processing (LOP) plant, consisting of crushing-washing & classification-hand sorting operations, to produce marketable grade lumpy ore and –10 mm de-slimed fines. These fines are intermittently treated in the COB plant. The higher silica content (greater than 1%) and low Cr/Fe ratio (less than 2.8) are the problems with these concentrates."

Jan 1, 2003