Search Documents

By P. H. Derbyshire

The use of continuous flight auger piles has increased significantly in the U.K. to such an extent that it is now the most widely used method of constructing small diameter bored piles. This paper describes the improvements in equipment, techniques and particularly monitoring that have led to this growth. A review of the equipment in use describes how purpose built self erecting machines have been generally adopted. Improvements in ancilliary equipment are described. Concrete has almost completely replaced grout and techniques have been developed to extend the length of reinforcement that can be placed. Leading specialist contractors have developed instrumentation to monitor the construction of the pile (in terms of time, depth, torque, concrete pressure and flow) and keep a record for checking. A further significant development of this monitoring by means of sensors at various levels in the auger stem is described. The results obtained from this monitoring are reviewed and future developments discussed.

Jan 1, 1989

By Tariq B. Hamid

Deep excavation is commonly associated with construction of different deep below-grade structural elements (e.g., basement walls and slabs, tunnels, retaining walls, tanks, utilities, etc.) Deep Excavation Retaining Systems (DERS) are required when open cuts with safe slopes are not possible. Careful analysis, design, and planning of the DERS are required to provide safe below-grade construction and secure nearby structures from damaging effects that may result from the deep excavation. Selection and design of temporary or permanent DERS (e.g., soldier pile and lagging, sheet piling walls, secant pile walls, tie backs, etc.) can have significant impact on time, cost, and performance. In order to design DERS using conventional methods, it is necessary to obtain shear strength parameters, angle of internal friction (ø), and cohesion (c), of retained soils. Residual shear strength parameters (ø'res, c'res) obtained from drained direct shear tests and triaxial tests on saturated samples have been commonly used in practice for the analysis and design of DERS. However, there are cases where ground water table remains at or below the base of excavation during the design lifetime of DERS. In such cases, the soil above the ground water table is in an unsaturated state. Therefore, it is important to account for the unsaturated conditions of soils in order to optimize the design of DERS. This paper is focused on implementing the basic concepts of unsaturated soils mechanics including matric suction and soils-water characteristic curve (SWCC) to estimate design shear strength parameters of unsaturated soils (i.e., ø°, c', and ø') for the design of a cantilever sheet pile walls, a typical case of study of the DERS. The results of this study indicate that the determination of unsaturated soil strength shear strength parameters is simple. In addition, using unsaturated soil mechanics theories has an outstanding impact on the design of retaining systems.

Jan 1, 2006

By Rudolph P. Frizzi

This paper presents different deep foundation systems and associated settlement records for high-rise building projects in the coastal areas of southeastern Florida. An introduction to the sedimentary soil and soft rock geology in coastal areas of southeast Florida is presented, and the deep foundation systems utilized include: piles of varying length, pile supported mat, preload and short piles, and drilled shafts. The implementation and associated settlement monitoring data of the different deep foundation systems are described through case histories involving 20 to 66-story buildings. In addition, the deep foundation systems and settlement monitoring results for twenty-one additional high-rise building projects in the coastal areas of southeastern Florida are presented.

Jan 1, 2003

By J. C. W. M. de Wit

An excavation, within which a tunnel is sunk as a part of the Centraal Station underground station (platform section) of the Noord/Zuidlijn ('North/South Line'), is to be created beneath the Amsterdam Centraal ('Amsterdam Central') station. The section beneath Amsterdam Centraal Station is characterised by the application of a particular technology in the form of, inter alia, the so-called 'sandwich wall'. This is a composite wall consisting of two rows of Tubex piles with a body of jetgrout columns in-between. This wall acts both as an excavation support wall and also provides vertical bearing. The installation of the wall, including both Tubex piles and jetgrout columns, within these specific conditions (limited height, sensitive historical building), within the design requirements set in terms of construction tolerance and water and soil retention, may be regarded as being a pioneering achievement. The environmental constraints are that the trains should continue to run, the inconvenience to passengers should be kept to a minimum and the historic station should not suffer any damage. Because of the complexity of the working conditions, the project is being overseen by a steering group of experts in the specified construction processes. In order to manage the project risks, jet grouting trials were initially carried out, in order to highlight and control execution problems; the practicability of the design is then tested. Work commenced on the sandwich wall in 2003, when the wooden piles were extracted at the locations where the sandwich wall was to be constructed; in 2004, the steel Tubex piles for the southern wall sections were installed. From May 2005, the construction of the sandwich wall got under way; in addition to the described process supervision, an extensive measuring programme was established, so that the process could be adjusted as necessary and the quality of the finished product determined. This applied to both individual columns and for the end product, the sandwich wall. The measurement results were processed for each column, interpreted and the effect on the work still to be conducted was assessed for each future column. Preventative and corrective measures were, if necessary, taken in order to control or counteract the measured defect. In addition to the process-oriented and qualitative measurements, various independent measurement systems at the station building served as a further control in order to prevent damage to the building.

Jan 1, 2006

By Vincent Jue

In December 2009, the Italian High Speed Rail Network AV began running over the full 1000 km system length from Turin, at the foothills of the Alps to Salerno, on the seacoast south of the volcano Mt. Vesuvius. It runs through Alpine rivers, highly seismic active zones, mountains, river plains, and through some of the most densely populated areas in Europe as well as some of its most expensive real estate. The Italian High Speed Network?s technical/economic constraints and its regulatory/socio-environmental concerns well may mirror similar obstacles set to confront the nascent California High Speed Rail Program. The two types of constraints must be dealt with together to reach the best construction solution. It is estimated that more than 20% of Italian High Speed Rail Network costs were spent on ground engineering including over 150 km of tunnels, 200 km of viaducts and bridges and 650 km of embankments and trenches. However, it also is estimated that 25% of costs were spent on social and environmental integration of the new rail lines including over 6 square miles of green offsets, 160 km of anti-noise walls, and 300 agreements for socio-environmental work. This paper will look at four examples of innovative ground engineering solutions, each with its own intricate set of constraints: ? Foundation system for viaducts across the ?Po? and ?Ticino? rivers. ? Soil consolidation under railway embankments ? Requirement of short tunnels for physical and environmental reasons ? Construction of railway stations in a confined right of way

Jan 1, 2010

By Cristhian C. Mendoza, Renato da Cunha, Bernardo Caicedo, Max Barbosa

"Abstract This paper shows that a raft alone is not sufficiently appropriate to address the uncertainty of underlying soil variability; therefore, a piled raft system is a better option for mitigating such uncertainty. To study the variability of soil, the behavior of the Piled-Raft Foundation was analyzed with a type of self-drilling micropiles: the ""Alluvial Anker"" (common name for this pile type in Brasilia city). These micropiles have been used in the city and have the advantage that the drill pipe also serves as reinforcement. The studied parameters belong to an elastoplastic constitutive model for strain-stress analysis of soil; variability of these parameters can be intrinsic and/or epistemic. Simulations were performed for a hypothetical Piled-Raft Foundation subjected to vertical loading using the random finite element method. The average parameters of the constitutive model were obtained through laboratory tests. The simulations of the load test were compared with results of a real scale experimental test conducted exclusively for this work in the field. It is analyzed the relative importance of the variability of some geomechanical parameters and their variation with depth is considered. In addition, it is discussed a comparison between the uncertainty of the geomechanical parameters and the uncertainty of the results of the vertical loading test. Finally, this paper shows that a decrease of the safety factor may occur when taking into account the variability of the parameters.IntroductionBrasilia is located in a highly weathered residual tropical soil (lateritic & latossol on pedogenetic concepts). This soil presents high content of alumina and iron due to the lixiviation process of the upper layers. As a consequence, the cemented structure is highly unstable and it can generate strong changes of volume (i.e. collapse) due to changes in both moisture and state of stresses. Therefore, a greater understanding of the construction of Piled-Raft Foundation systems on this particular soil conditions is needed – especially because it covers more than 80% of the surface area of the Brazilian Federal District.Thereafter, this work investigates the influence of the variability of the soil parameters over the uncertainty of the Piled-Raft Foundation design. The studied parameters belong to an elastoplastic constitutive model for strain-stress analysis of soils. The simulations were performed for two hypothetical Piled-Raft Foundations subjected to vertical loading by using the stochastic finite element method. The results were compared to real load tests in Piled-Rafts with “Alluvial Anker” pile types."

Jan 1, 2014

By Andrzej Tejchman

Calculation of pile foundations should possibly truly reflect its real work, mainly with respect to the value and distribution of settlements, pile internal forces and bending moments within a slab. Many empirical and theoretical methods serving for an assessment of the settlements of pile group overestimate its actual values obtained from field measurements (see Tejchman et al., 2001). In the paper a simple engineering method for calculation of pile foundations is presented. The method takes into account the interaction between the slab and a soil together with the phenomenon of non-uniform deformation of the soil-pile subsoil, particularly under large foundations. In the method the scheme of the slab resting on one-parameter elastic subsoil is assumed. The comparison of the calculation results for existing pile foundation with the field measurements shows good agreement between those values.

Jan 1, 2002

By Derek J. Lennon

Ground conditions in central Glasgow generally comprise loose granular deposits overlying stiffer soils. CFA piling would normally be preferred for urban sites in these ground conditions, but flighting of the superficial deposits has on occasions resulted in building damage. Over the last five years rotary bored piling with vinyl polymer support fluid has proved to be an economic alternative to bentonite slurry. Two case histories in central Glasgow are described in this paper, one for piles founding in granular soils and one for piles founding into bedrock. A comparison is made between the methods required for disposal of the liquid waste from bentonite and vinyl polymer slurries.

Jan 1, 2006

By Bruce Haldeman

Timber has been used as pile support for structures for 6,000 years. Some means of preservation of wood go back almost that far. Timber piles support all types of structures ? some are buried below the water table; others raise a home for protection from animals or a chief's home for prestige. Millions of wood piles have been driven for bridge support. Earlier piles were driven by hand then by ingeniously raised weights. Charring, animal fats and oils have been used for preservation. Coal tar creosote and other preservative methods started only in the early 1800's and give effective protection.

Jan 1, 1984

By Robert B. Bittner

The Sutong Bridge across the lower Yangtze River in China will have, when completed, the longest span (1,088 m) and the highest towers (306 m) of any cable stayed span in the world. The foundations for this record setting span will also be record setting. They are located in water depths exceeding 30 m with maximum flows exceeding 3 m/sec. The soil at the site of the main pylons consists of layers of silty sands and silty clays extending to bed rock at 270 m below river elevation. This paper describes the innovative methods used by the team of foundation designers and constructors to support this record setting bridge at this very challenging site. This paper covers three specific topics related to the foundations of the Sutong Bridge: ? Design and construction of the 131 drilled shaft (2.8/2.5 m diameter and 114/117 m long) under each of the two main pylons, ? Design and construction of the scour protection for the two main pylons, ? Construction methods used to construct the waterline pile caps (113.8 m by 48.1 m by 13.3 m deep) under each pylon.

Jan 1, 2005

By Jiwei Duan

The deformation and load transfer behavior of a single soil-cement column are studied with the finite element method. The results show that there is an effective length for a soil-cement column. Beyond this length, the settlement of the column is approximately equal to a constant. The effective pile length is introduced to the concentric cylinder approach (Randolph and Wroth 1978), and an analytical formula for estimating the settlement of a single flexible pile is presented. A second analytical formula for determining the effective pile length of a soil-cement column is obtained and an example shows that the calculated and measured results are in quite good agreement.

Jan 1, 2002

By Hodjat] [Shiri

A 4-legged jacket structure was installed by an Offshore Installation Contractor (OIC) in the Persian Gulf. In addition to four open-end pipe piles, six conductors were installed by OIC. During the installation of the piles and conductors, some cemented layers were encountered, which had not been accounted for in the foundation design performed by an independent well known offshore geotechnical site investigation contractor (OGSIC). Six months later, the Drilling Company (DC) hired by Client to execute the wells, reported that all of the six conductors were presenting anomalies, such as vertical misalignments up to 10o and/or collapse of the conductors tip and mid height. The DC faced with serious problem in drilling of the wells and in spite of several times milling the conductors and spending 40 days unpredicted extra time, some of the routes could not be opened and Client lost millions of dollars due to direct and indirect associated costs and expenses. This paper presents a complete overview of all engineering, construction and specially geotechnical investigations and shows that how an inaccuracy in interpretations of the results of an offshore geotechnical site investigation as the main reason in this case study can cause serious damages to whole project with unbelievable time and cost impacts some times up to millions of dollars.

Jan 1, 2006

By Francis J. Arland

The installation of augered cast-in-place (ACIP) piles requires careful quality control to assure a successful pile installation. Unlike steel, pre-stressed concrete or other types of driven piles, which are shop fabricated, delivered to the site and typically driven to a minimum tip resistance, augered cast-in-place piles are installed to a pre-determined tip elevation or to a refusal criteria. The structural section of the ACIP pile is constructed during pile installation and cannot be inspected prior to installation. Therefore, a carefully administered quality control program is essential to a pile foundation that will meet or exceed design requirements. This requires an experienced team consisting of the Geotechnical Engineer, Contractor and Inspector. The focus of this paper is to discuss the responsibilities and duties of the ACIP piling Inspector. Qualifications of the Inspector The qualifications of the inspector are related to the complexity and difficulty of the proposed project. Ideally, the Inspector should be an individual with a degree in civil engineering with special emphasis in geotechnical engineering. A properly trained technician with geotechnical engineering experience working under the direct supervision of a geotechnical engineer may be able to provide competent inspection on some projects. It is important that the Inspector have a good understanding of subsurface and ground water conditions and how they will affect pile installation. The Inspector must understand ACIP pile installation procedures and be able to communicate with the Contractor, Structural and Geotechnical Engineers; and maintain a detailed pile record for each installed pile.

Jan 1, 1997

By F. W. Liang

The geology of pearl River estuary belongs in strong weathered rock quaternary geological systen, so the conditions are complication. Since 80's we built the first deepwater wharf of Shenzhen chiwan port which has 3 berths of 10000 dwt, We have built 3 berths for vessels of 40000 dwt both in Shekou Port and Chiwan port. The berths for carriers of 10000 dwt in Yantian Port of Dapeng Bay are constructing now. In the five years, We built more than 20 deepwater berths of 5000 dwt to 40000 dwt. This paper will introduce how to solve the difficulties of the complex geological conditions and how to use the new fashion construction. We will reduce the period of engineering construction and get good quality and make a good beginning of rapid development of port construction in ShenZhen Special Economic Zone.

Jan 1, 1991

By Upendra L. Karna

The pile capacity gain with time evaluated and implemented for the construction of the Route 21 Viaduct in Newark, NJ, U.S.A is discussed in this paper. The project consisted of the replacement of more than 3.2 km of viaduct and ramps. The project site consists of thick residual materials deposited by the Wisconsin Glacier over sedimentary rocks. The upper portion is glacial-lacustrine deposit underlain by marginal morainic till and stratified drift. Subsurface investigations identified significant variations in layer thickness and grain size consistency. The site was characterized into 4 Soil types, based on subsurface soil behavior. Closed end 600 mm and 450 mm diameter driven pipe piles were used for the foundation. Loading tests conducted during an advanced construction contract, established that a significant soil set-up could be expected. For the first construction contract, a pilot loading test program consisting of 112 dynamic loading tests and 77 re-strikes (at 2 to 4 weeks) using the PDA (Pile Driving Analyzer) with CAPWAP (Case Pile Wave Analyses Program) was conducted to establish the soil set-up behavior. Nine (9) quick static loading tests were conducted to substantiate the long-term pile capacity. Based on the loading test results, average set-up factors were established and utilized for developing production pile driving criteria. Bearing resistance with depth was analyzed and reviewed. The set-up factors varied significantly, ranging from 1.05 to 1.89, and averaged about 1.30. Conclusions are derived. Set-up factors behavior for each soil type plotted by linear regression are presented and discussed. An appropriate set-up with time relationship for a glacial soil is suggested.

Jan 1, 2006

By Robert E. Fosse

Driven 14-inch-square concrete piles were used as the foundations of Genentech Hall at the new University of California, San Francisco Mission Bay Campus. The five-story, steel eccentrically-braced frame building is currently under construction at a 43-acre property located in a former large shallow marshy inlet from San Francisco Bay. The piles were driven through 10 to 25 feet of fill and 20 to 60 feet of soft compressible Bay Mud into an underlying dense sand layer. Pile design capacities were developed for traditional allowable stress design, load factor and resistance design, and ultimate design criteria. The ultimate level capacities were for checks of loads occurring when the links in the eccentrically-braced frame yield during an earthquake. A load test program was performed to confirm pile design recommendations. Two test pile locations were selected for compression, tension, and lateral load tests to evaluate pile capacity and pile/soil stiffness under long-term, short-term and rapid loading conditions. Maximum test loads were 1000 kips downward, 350 kips uplift and 50 kips lateral. Foundation construction began by driving 34 indicator piles with a Delmag D46-32 diesel hammer of 113 foot-kips maximum rated energy. All indicator piles were monitored during initial driving using the Pile Driving Analyzer. Restrike data, obtained several days after initial driving, indicated significant pile-soil setup and typical pile capacity increases from 750 to 1000 kips. The majority of the 1242 production piles were then driven to acceptance criteria of 75 blows per foot and a minimum embedment of 10 feet into the dense sand bearing layer. Piles driven to full length without achieving the blowcount criteria were evaluated on a case-by-case basis. Acceptance of these piles was established by evaluating restrike data.

Jan 1, 2002

By Ivan Jackson Madura

The new Paradisus Coco Beach Resort in Rio Grande (PR) is located on an old swamp area, which has been filled with relatively clean to silty sands. The swampy deposits consists of organic silts, peat and loose fine to medium sand and silty sand. The project requires the placement of 1.0 to 1.5 meters of additional fill together with the construction of light structures. The need for the fill will trigger the development of settlements in the underlaying weak and compressible stratum. Furthermore, the susceptibility of the loose sand to liquefaction during an earthquake was considered. This paper describes the soil improvement by means of vibro-replacement, the purpose of which was threefold: reduction in total and differential settlement, acceleration of settlements during the surcharge period and densification of the loose sand to reduce its liquefaction potential. The predesign is presented together with relevant construction details of the preliminary trial areas from which the final column diameter and grid spacing were derived. Instrumentation together with settlement observations during the surcharge period are presented as well and compared with the initial predictions.

Jan 1, 2002

By Jorj O. Osterberg

Until ten years ago, the largest load tests on drilled shafts (bored piles) were about 3,000 tons (27MN). These tests were made with kentledge (large weights, usually concrete blocks) stacked up as a reaction to the applied downward load of a hydraulic jack. In some cases, the jack load is resisted by a load frame held down by piles or anchors connected to the frame. When the test loads exceed 3,000 tons (27MN), these methods become cumbersome expensive and time consuming. The Osterberg (O-cell) test method does not require any reaction load. It has become the only cost effective method for static load testing of high capacity shafts. Over 650 load tests have been performed with this method, 86 of which were over 3,000 tons (27 MN) and 40 over 5,000 tons (44 MN), and the largest test load was 17,000 tons (150 MN). Tests have been made on sands below the water table, shafts ending in rock sockets, and cemented sands and gravels. Test results and details for selected load tests are discussed.

Jan 1, 2002

By Frank J. Arland

Augered-Cast-in-Place piles have been used successfully for many deep foundation applications. The four case studies discussed herein describe ACIP pile projects where problems developed during ACIP pile installation requiring changes to the method or sequence of installation. The case studies illustrate the importance of understanding existing subsurface conditions and project constraints when considering the use of this pile type. Ground loosening and over-excavation of soil during the augering process, a significant concern for fine to medium sands and non-plastic silts below the water table, can significantly impact adjacent structures. This risk needs to be evaluated during the pile selection process and generally can be mitigated, but not eliminated, by requiring the use of piling equipment with high torque and slow auger rotation speed to advance the auger with minimum amount of rotation. In some applications where high lateral stresses in the soil are present such as at the base of retaining structures, the use of ACIP piles may not be appropriate if structure movement is unacceptable. On the other hand, ACIP piles have been successfully used to support deep foundations in preconsolidated varved deposits where the new structure was designed to accommodate recompression settlement.

Jan 1, 2004

By Guan Jichang

An abandened breakwater, located at the rear of No. 2 berth in Dongdu Port area of Xiamen City, was not cleaned thoroughly when the backfilling of sand started. The uncleaned stone layer was about 2 to 3 meters deep, with the average piece of stone weighing about 1 to 3 kN. A large grain storing house, 220X 60m2 in area, was designed and built at the above mentioned complicated site. The foundation of the grain house are made up of the cast-in-situ piles. It is well known that it is difficult for the submarine engineering drill to go down through such large-sized stones. Having com-pared the various plans, a final decision has been made which involves explosions with small amounts of charge plus cone bit in the enlarging of the size of the pores. Such a method has successfully prevented the pores from slumping and made it possible to fulfill the project without any difficulties. This paper also introduces the ways in effectively dealing with each individual stone.

Jan 1, 1991