Search Documents

By Issa S. Oweis

Limestone is a sedimentary rock composed primarily of calcite (calcium carbonate). In the presence of an aqueous solution of carbon dioxide (carbonic acid) bicarbonate radicals (2HCO3)- are produced that are highly soluble. The same type of reactions occur in terrains where dolomite (calcium magnesium bicarbonate) reacts with carbonic acid to produce highly soluble bicarbonates (4HCO3)-. The source of carbon dioxide is the small content in rainfall but to a large extent from the organics in the soil. The solution activity depends on many factors including the content of carbon in the rock, acidity of soil water, groundwater velocity and other factors. The resulting features are referred to in literature as sinkholes, solution channels, caves, karstic topography, and cavernous limestone. The presence of solution features affect the shafts in several ways: (a) the shaft resistance is affected by voids along the shaft, (b) concreting of the shaft should consider the presence of voids along the shaft, and (c) the shaft base may be in close proximity to a solution feature that may cause future collapse under structural loads. Methods to mitigate such effects include verification of rock to below the base (vertically and laterally). Cavities are stable by virtue of arching in the rock. Under the action of end bearing from a shaft, the arch may collapse depending on its proximity to the base of the shaft and the strength of the rock. This paper focuses on this issue. Finite Element analyses are conducted to relate shaft end load and bearing area that will produce failure based on given rock properties, size and location of cavity. Failure is defined as settlement of the base equivalent to 5% of shaft socket diameter. The software Plaxis is used for analysis. The rock is considered as c-f material derived based on Hoek-Brown failure criteria (2002 edition) that is based on Geological Strength Index (GSI).

Jan 1, 2009

By Kenneth Gavin

Design practice for piles installed in Irish glacial till has developed in an ad-hoc manner, based on the results of un-instrumented load tests. This had led to designers using similar design parameters for both CFA and displacement piles. To address the concerns of industry a series of instrumented pile tests were performed by two Irish Universities. These tests summarized herein, revealed that CFA piles develop higher shaft resistance than piles driven in glacial till. However, they exhibit low base stiffness and the end bearing resistance that can be mobilized at acceptable pile settlement is low. The use of simple non-linear elastic design approaches to predict the load-displacement response is considered. The methods are used to predict the capacity of two large diameter CFA piles installed in glacial till. While the predictions were reasonably accurate at predicting the initial load-displacement of the piles, significant creep settlement developed at higher load levels. The cause of the creep settlement was investigated through the use of plate load tests and the consequences for pile design are discussed.

Jan 1, 2009

By Amalia Giannakou

This paper utilises 3-D finite-element modeling to study the static and dynamic lateral harmonic response of inclined piles, in a homogenous and a non-homogenous soil, modeled as a linear hysteretic medium. The results of a comprehensive parameter study are presented in the form of dimensionless plots of: (a) static and dynamic swaying and rocking stiffnesses and damping ratios, and (b) distribution of internal forces (bending moment, shear and axial force) with depth. These plots can be readily utilised in practical applications and they offer insight on the role of the inclination in the response of flexible piles.

Jan 1, 2006

By Eiji Kojima

In this research, dynamic and static load tests were performed on permanent foundation piles which had a pile length of 30 m, 800 mm in outer diameter and 15 mm in wall thickness. In this site the dynamic horizontal load test on a smaller test pile, 12 m in length, 500 mm in outer diameter and 12 mm in wall thickness, was also carried out. The static horizontal load versus horizontal displacement derived from the dynamic load test conformed well to that measured in the conventional static horizontal load test of the pile with 800 mm diameter. Then an attempt was made to predict the horizontal load displacement of the pile with 800 mm diameter based on the results of the dynamic horizontal load test of the pile with smaller diameter of 500 mm.

Jan 1, 2006

By Richard J. Finno

This paper presents an overview of methods that can be used to predict damage to buildings as a result of excavation-induced ground movements and describes an adaptive management approach for predicting, monitoring, and controlling excavation-induced ground movements. Successful updating of performance predictions depends equally on reasonable numerical simulations of performance, the type of monitoring data used as observations, and the optimization techniques used to minimize the difference between predictions and observed performance. This paper summarizes each of these factors and emphasizes their inter-dependence. Case studies are presented to illustrate the capabilities of this approach. Examples are given to show how optimized parameters based upon data obtained at early stages of excavation can be used to predict performance at latter stages, and how they can be applied to other excavations in similar geologic conditions.

Jan 1, 2010

By Roy Jennings

The Discovery Expedition of St. Charles, MO chose to build its two-story museum in the flood plain of the Missouri River, near the starting point of the Lewis and Clark Expedition. Should the lower level be inundated at flood stage, plans call for the replica riverboats to be moved by trailer to higher ground. The museum's design required an open span structure with heavily loaded footing or piles. Spread footings could not be used due to the compressible soil profile. The location, in a historical district, precluded dynamically driven piles. Sixty-three uncased Helical Pulldown Micropiles were driven to the bearing stratum to support the museum with minimum disturbance. There were no spoils to dispose of during construction and the piles were completed in eight working days with minimum impact to the environment and neighborhood. The maximum working load required was 84,000 pounds (374kN). Test results are given in the form of installing torque.

Jan 1, 2003

By Narong Thasnanipan

In Bangkok due to the prevailing condition of subsoil (existence of considerably weak stratum at top part) deep-seated large diameter bored piles of over 50 m depth with 0.8 -1.8m in diameter have been mainly used for heavy structures such as high rise buildings, elevated expressways, flyovers and more recently for underground subway stations of the first Bangkok MRTA system. As a part of pre-planned quality assurance regime and retrospective investigation, integrity of the piles are tested to obtain the information with regard to the potential deficiencies of the constructed piles which may have formed during pile construction process or may have been attributed by other activities after construction of the piles. An overview of three commonly used non-destructive tests such as sonic integrity, sonic logging and high strain dynamic load tests on deep-seated piles in Bangkok subsoil is presented in this paper. Advantages and limitations of each integrity test are discussed.

Jan 1, 2004

By Donald R. McMahon

This paper presents a unique case history that documents the use of a braced secant pile wall to underpin a heavily loaded footing inside of a manufacturing plant. Construction of a pit for a new manufacturing process directly next to the footing necessitated the underpinning. The footing supports an overhead crane that needed to remain operational throughout construction of the pit and therefore, settlement of the footing could not be tolerated. The base of the footing was about 7.7 feet above the base of the 17-foot deep excavation. The footing bears on a silty clay deposit that grades from a stiff consistency beneath the footing to a soft/medium consistency near the base of the pit excavation. This paper describes the design and construction of the secant pile wall and bracing to control wall deformations, ground movements and settlement of the footing. The footing was monitored for settlement throughout construction of the pit and no measurable movement was observed.

Jan 1, 2006

By Narong Thasnanipan

This paper presents the outcome of the contest on the prediction of the static axial load capacity of diameter 1.20m bored pile founded at 46m below existing ground. The test pile was constructed by wet-processed method and instrumented with vibrating wire strain gauges. Different methods used by the contestants in prediction of load-settlement characteristics are described and compared with actual load test results. Load-displacement behavior of test pile is found to be better than expected. Major difference between prediction and actual test is the higher frictional resistance of Second Sand Layer achieved in the actual load test. The hyperbolic load transfer method used by one of the contestants was applied to back-analyze the load-displacement characteristics of the test pile at different conditions.

Jan 1, 2006

? Hollow Stem Auger ? Drill Bits ? Leads/Torque Arm ? Hydraulic Gearbox ? Hydraulic Power Unit ? Grout Pump ? Crawler Crane

Jan 1, 2000

By W. Robert Thompson

Hurricane Katrina caused significant damage to transportation structures on the Gulf coast in August, 2005, including the destruction of the US 90 Bridge over Biloxi Bay, Mississippi. Part of the successful design/build proposal for the replacement bridge included a comprehensive test pile program of indicator piles and load test piles in the geotechnical investigation program. A total of 22 indicator piles were installed on the project using the pile driving analyzer to monitor the pile behavior. Five load tests were performed: two axial Statnamic, two lateral Statnamic, and one static axial. The results of the test pile program established driving criteria for production piles that included end-of-drive blow counts and pile tip elevations with an appropriate allowance for setup. The program also confirmed that the planned installation equipment and techniques of GC Constructors, a joint venture of Massman Construction Co., Kiewit Southern Co., and Traylor Bros., Inc., would install the piles to the design tip elevations before production piles began. An extensive program of restrike measurements at a range of times after initial driving of the indicator piles provided a systematic documentation of pile setup in the soil profiles on the site. These resistance values were used to develop a dimensionless setup factor ?S? as the ratio of the restrike resistance to the end of drive resistance. This factor varied from 1.5 for piles penetrating clays and tipped in sand to 3.0 for piles bearing completely in clay and helped establish an end-of drive blow count that included an allowance for setup. The CAPWAP analyses of restrike data with setup and the load test data were used to confirm the design unit side shear and end bearing values developed from the borings and static capacity calculations and to select the design pile lengths.

Jan 1, 2009

By Dimitris Pachakis

In this paper, the authors give a brief overview of the current practice guidelines and tools for the seismic design of sheet pile quay walls, emphasizing how the design guidelines are lacking when the existing structure performance evaluation is required to meet performance-based criteria. Relying on recent experience they explain how the existing practices can be amended to focus more on performance evaluation as opposed to design. An example is given of an old sheet pile quay wall analyzed and evaluated for its performance according the recent performance criteria devised for Californian Marine Oil Terminals.

Jan 1, 2011

By J. X. Wu

An investigation on the seismic damage to buildings with pile foundations in Tianjin region, was conducted after the earthquake which hit Tangshan in 1976. It showed that most pile-founded buildings have an excellent aseismic capacity. In this paper, several pile-founded projects suffering the seismic damage are introduced as examples, simplified calculations are made of the vertical bearing capacity of pile foundations and of the horizontal seismic force, and suggestions are presented in conection with the design of pile foundations in the liquified ground soil. The paper shows a frame structure which has a plie foundation with a box-shaped base. Analyses if its response to the earthquake has been carried out in accordance with the F.E.M. and results have been obtained.

Jan 1, 2010

By Wei Zheng

A pulverized coal fired power plant is being built in Osceola, Arkansas, along the Mississippi River. The subsurface soil conditions consist of a certain amount of very soft clayey silt and clay underlain with a medium dense sand layer and a dense sand layer. The site has been raised four to five feet with fill material consisting of sand and gravel. Consolidation settlement due to the fill is expected to cause negative shaft resistance (downdrag) on the pile foundations. The site is located in a high seismic hazard area - the New Madrid Seismic Zone (NMSZ). The liquefaction analyses indicated that there is a high liquefaction potential in the medium dense sand layer. Load tests are needed to determine the shaft resistance and the end bearing of each soil layer for design purpose. Two types of pile foundations ? augered pressure grouted displacement pile (APGD) and partial augered pressure grouted displacement pile (P-APGD) were considered for this project. Ten pile load tests, including five compression tests and five tension tests, were performed for three different areas. Strain gauges were installed for the compression tests. The APGD and P-APGD piles were installed side by side for comparison. In addition, three additional dynamic tests were performed to supplement the information from the static load tests. Load deflection curves for the compression tests were predicted, and the failure loads were interpreted using four different methods. The shaft resistance and the end bearing were determined from the strain gauge data and were used to back calculate the ultimate capacity. The back-calculated capacities are in good agreement with the predicted failure loads; they were further verified with the tension load test results.

Jan 1, 2007

By Bill Starke

The acceptance of AugerCast piles in Canada has been limited. Many engineers are apprehensive about the quality of the piles produced by this method. However, advances in the sensing instruments and computer technology can now provide satisfactory levels of quality assurance. Post construction tests such as the sonic echo method can give an indication of pile shaft integrity. Computerized monitoring of the pile installation process is an immediate and more positive method of quality assurance. The computer continuously measures and records the parameters which indicate the quality of the pile. If these parameters do not indicate a satisfactory pile, it is replaced before the concrete hardens. Computerized monitoring of the installation process is another tool available to the engineer. The data from this system analyzed with soil borings, site inspections, and possibly sonic tests can provide the engineer with enough information for pile certification.

Jan 1, 1997

By Luo Yang

It has been known that after initial pile driving, pile capacity gain over time (set-up) could constitute a significant portion of the total pile capacity. In the past, there has been very little guidance for incorporating pile set-up capacity in design. This may be due to large uncertainties involved in predicting the pile set-up. A comprehensive statistical database is developed to describe the increase of pile axial capacity with time, known as set-up, when piles are driven into sand. Based on the collected pile testing data, pile set-up is significant and continues to develop for a long time after pile installation. The statistical database shows that a lognormal distribution can be used to describe the probabilistic characteristics of the predicted set-up capacity using Skov and Denver?s equation. The main objective of this paper is to incorporate the set-up effect into a reliability-based Load and Resistance Factor Design (LRFD) of driven piles in sand. A First Order Reliability Method (FORM) is used to derive separate resistance factors that would account for different degrees of uncertainties associated with the measured short-term capacity and the predicted set-up capacity from the proposed semi-empirical equations. The incorporation of set-up effects in the LRFD helps improve the prediction of the total capacity of driven piles, resulting in more economical design. A practical design procedure within LRFD framework to incorporate the pile set-up effect is outlined at the end of the paper.

Jan 1, 2006

By David A. Staab

Numerical modeling was used to investigate the feasibility of using two geophysical imaging techniques, cross-borehole ground penetrating radar (XBGPR) tomography and electrical resistivity (ER) tomography, for detecting and characterizing defects in deep-mixed soil columns. XBGPR modeling was accomplished with a three-dimensional numerical forward modeling code and a two-dimensional inversion routine. Spatial variations in apparent dielectric constant (Ka) and attenuation (a) were mapped. Electrical resistivity modeling was accomplished with a three-dimensional numerical forward modeling code and a three-dimensional inversion routine. Spatial changes in electrical resistivity were then mapped. Three different types of defects were simulated, in addition to a defect-free column. The computer simulations suggest that XBGPR tomography and ER tomography might be useful, non-destructive methods for detecting and estimating the extent of defects in deep-mixed soil columns. The results show that small, isolated defects might be difficult to detect, but defects approximately equal to or larger than the sampling interval (for XBGPR) or vertical electrode spacing (for ERT) should be detectable.

Jan 1, 2004

By Robb L. Swenson

Construction of foundations for the Skyway Segment of the San Francisco Oakland Bay Bridge required innovative techniques due to the mass of the structures being inserted and the unique subsurface of the Bay. Twenty of the pier structures required large sheet pile cofferdams. Eight other foundations were installed in open water without cofferdams at the deeper part of the Bay. This narrative will present the initial planning, as well as the stages of installation, for each type of foundation. The first section will discuss foundation constructability modifications made during the initial planning phases of the project. Considerable effort was expended by Caltrans, the owner, T.Y. Lin the designer, and KFM (Kiewit/FCI/Manson) the contractor in modifying the design to assure that required tolerance would be maintained during the installation of the foundations. The final section will describe the steps required for installation including: initial access dredging, installation of cofferdams, preparation required to install the footing boxes, footing box installation, foundation support pile installation, and pile to box connections.

Jan 1, 2005

By Vasileios A. Drosos

The response of pile foundations to lateral loads is an important factor for the successful performance of several critical structures. A new numerical code for the analysis of single piles under lateral load is outlined. The code can simulate (through appropriately chosen parameter values) not only the non-linear behavior of soil, but also the inelastic structural response of the pile itself under lateral load. Emphasis is given on the calibration of model parameters and the verification of the code. For the calibration of the parameters, data is used (a) from the well documented in the literature p-y curves, and (b) from experiments conducted either in full scale or in the centrifuge. Results are compared to those of well known published codes for inelastic analysis of single piles under lateral load.

Jan 1, 2006

By F. Schlosser

The extension of Montparnasse Station in Paris required the construction of supports of very high unit capacity to support a particularly rigid super-structure. The majority of the site is characterized by the existence of old limestone quarries at a depth of approximately 20 metres. These workings have been backfilled in some places, have collapsed in some places and have given rise to local subsidences in the marne layers above them. This paper addresses the steps taken by the group of companies and their consultants to evaluate the equivalent stiffnesses of the supports necessary for the design of the superstructure, and gives details of the construction techniques chosen by the foundations specialist to adapt to the particular conditions encountered on this site.

Jan 1, 1989