Search Documents

By V. M. Troughton

Further pile load testing has been carried out at Canary Wharf to compare the performance of base grouted and ungrouted bored piles founded in the Thanet Sand. The testing regime included three preliminary test piles and two working test piles. The results of these tests are summarised in Table 1 below. Two of the preliminary test piles were located only 14m apart to compare the performance of a base grouted and ungrouted pile in similar ground conditions. The load/settlement behaviour of these two preliminary test piles are compared on Figure 1. All the piles were drilled under bentonite with a drilling bucket. In the base grouted piles four grouting tubes were placed with the reinforcement cage to within 500mm of the pile toe. After the pile had been concreted these grouting tubes were then extended to the pile base by drilling and packers were installed. Grout was then injected into the four tubes simultaneously.

Jan 1, 1991

By Susheel R. Kolwalkar

A significant increase in the side shear capacity over a period of time is often observed in case of driven piles. This phenomenon is referred to as ?setup? or ?freeze?. This phenomenon cannot be predicted based on the knowledge of the engineering properties of soil. Different kinds of mechanisms have been proposed in order to explain set-up in cohesive soils. In engineering practice, set-up is incorporated in design on the basis of empirical formulae and depends to a large extent on personal experience and judgment of the design engineer. Set-up is a natural process which cannot be accelerated by any existing practice. A research was initiated to investigate the mechanism of pile set-up in clayey soils and explore the possibility of accelerating the set-up process by an electro-kinetic method. The system chosen for the present study consists of a prototype steel pile driven in kaolinite clay. A laboratory test program was developed at Cleveland State University in order to meet the goals of the proposed research. Results obtained from these tests are very encouraging and show pile capacity increase of 200% within the first 5 days of electric gradient application versus those that experience natural set-up. In this paper, theoretical considerations and laboratory test results are presented and discussed.

Jan 1, 2008

By James J. Anderson

In this talk I will report on an effort to reassess the risk of pile driving to juvenile salmonids migrating through Puget Sound. The study was motivated by the concern of the construction industry that provisions restricting pile driving during the spring migration is resulting in an unbalanced burden to the industry. In simple terms the industry wants to know if some construction can be conducted in the spring without harming the juvenile fish. Fisheries agencies have agreed to reconsider their regulations in the context of additional studies. So, in this talk I will present some thoughts on risk assessment in general and the results of our study to assess the impact of pile driving on Snohomish River juvenile pink and chum salmon that migrate through the Navy Homeport construction site at Everett. The research, which is being carried out by the Fisheries Research Institute at the University of Washington, was planned and is supported in a joint effort including: the Washington Department Fisheries, National Marine Fisheries Services, U.S. Fish and Wildlife Service; General, Manson, and Hurlen construction companies, the Department of Transportation and a number of Puget Sound ports authorities. I will first briefly discuss the early life history of the juvenile salmon the regulations are designed to protect Second, I will outline the legal criteria required for risk regulation and some specific thoughts on how a reassessment of pile driving risk might be approached. With this basis I will report on our research and how it can be applied to a new risk assessment.

Jan 1, 1990

By Michael J. Atwood

Many buildings in Boston are founded on untreated wood piles, which can deteriorate and lose their structural capacity if groundwater levels are lowered below the tops of the piles, exposing the wood to air in the unsaturated soils that surround the piles. The problem of wood pile deterioration due to lowered groundwater levels in Boston first became evident in 1929 following discovery of rotten piles beneath walls of the Boston Public Library building. Repairs to reconstruct the library building?s wood pile foundations were made in 1930 using pit underpinning methods. Today, more than 80 years later, the subsurface conditions beneath several of Boston?s historic neighborhood areas continue to be plagued with low groundwater levels - regrettably resulting in ongoing deterioration to the wood piles that support some of Boston?s oldest and most beautiful buildings. Pit underpinning is still recognized as the preferred approach to repair wood piles and restore uniform foundation support beneath the impacted buildings. This paper provides a brief historical review of the land filling in Boston through the early 1900s that led to the use of wood piles as building foundations. Also discussed is the impact that groundwater level can have on the long term performance of wood pile foundations and the pit underpinning procedures used to reconstruct decayed wood pile foundations in 1930 beneath the Boston Public Library, and today beneath some of Boston?s oldest buildings. Also included are discussions on engineering controls and permitting requirements that help ensure safety and protection to the workers and buildings during underpinning, and some procedures being used to supplement and improve the loading capacity of the reconstructed foundations and facilitate construction of new useable below-grade space.

Jan 1, 2011

By Mark Maday

As part of the I-94 North-South Corridor reconstruction program, the Wisconsin Department of Transportation (department) is reconstructing the Mitchell Interchange in Milwaukee, Wisconsin. Located on the south side of Milwaukee near Mitchell International Airport, The Mitchell Interchange interconnects I-94, I-43 and I-894. Reconstruction began in 2009 with the letting of the first advance contract for local crossroad bridge reconstruction. A second advance contract for construction of collector-distributer roads on each side of the I-94 mainline was completed in 2010. The main contract involving reconstruction of the core of the Mitchell Interchange was let in the summer of 2010, and is scheduled to be completed by the end of 2012. The core contract includes construction of three cut and cover tunnels along two system interchange ramps. Construction of the three tunnel structures is on the critical construction path. The contract includes an interim contract completion date that requires the tunnels to be open to traffic by the end of 2011. A top down method of construction using drilled shaft secant piles for the sidewalls of the cut and cover tunnel structures was selected as the preferred structure type to address subsurface and construction schedule challenges. The department identified in pre bid coordination that no cost reduction incentives would be reviewed or accepted for changes in tunnel wall type. A major component of the tunnel structures requires the installation of 1,500, 4-foot diameter secant piles. This paper presents mitigation strategies to manage construction risks associated with the installation of the secant piles including; prequalification of the secant pile subcontractors, requirement for use of full depth temporary casing, a site specific quality control plan, specifying drilling equipment, and developing a geotechnical baseline report for this critical component of the Mitchell Interchange reconstruction project.

Jan 1, 2011

Jan 1, 2001

By O&apos, M. W. Neill

Mini-piles have been found to be a practical, technically correct remedial underpinning method. They can be constructed in limited access areas with very little disruption. Experience indicated that mini-piles installed using a down-the-hole soil displacement hammer would be particularly effective in the "bottomless" Beaumont Clay formations in the Houston, Texas, U.S.A. area. The University of Houston Foundation Testing Facility was ideally suited to perform tests on mini-piles. The availability of extensive geotechnical data and previous pile test results was invaluable in evaluating the mini-pile test data. As expected, the mini-pile test results were consistant with test results from large sized driven piles in the same soil formation.

Jan 1, 1989

By Mario Mauro

The article illustrates the Hydromill technology, as applied in urban sites, and its advantages in terms of quality of the end product, mitigation of the construction impact, and optimization of the logistics at the site. Also highlighted are the main features of the excavation equipment and slurry treatment plant. Two recent urban applications of this technology in Europe are briefly described, together with the forthcoming application to the Central Artery/Tunnel Project in Boston. Introduction The Hydromill technology has been used extensively in Europe in the last decade for slurry wall construction in urban environments. In Italy, this technology has been applied by Ing. Giovanni Rodio & C., Impresa Costruzioni Speciali S.p.A. in two large projects. The first project is the construction of Stations Darsena and San Giorgio of the first metro line in Genova. The second project is the "Cut-and Cover" tunnel for the railway link in Torino. Hydromill technology will be used for the construction of the Soldier Pile Tremie Concrete walls of the Boston Central Artery Tunnel Project, contract C14C2, Utility Relocation at Fulton Street.

Jan 1, 1994

By Yvone Franco Crosato

The dense population of Hong Kong requires the construction of tall buildings in reclaimed areas or perched on the slopes of the many hills. The large loads to be supported are carried by deep foundations. Many of those are bored piles, to rock, of diameters up to the 3.0 m. of today.

Jan 1, 2000

By Rudolph P. Frizzi

Quality control is essential for augered cast-in-place (ACIP) piles (also known as continuous flight auger (CFA) piles outside the United States) and augered displacement (AD) piles since the pile is constructed below the ground surface out of the direct sight of the personnel constructing and inspecting the pile. ACIP piles are being successfully constructed to support high-rise structures, arenas and stadiums, mass transit systems, and power and industrial facilities. The use of AD pile technology is also gaining ground in the United States, typically utilizing proprietary systems such as Omega (currently utilzed by Richard Goettle Inc., and LG Barcus and Sons, Inc.), Berkel, and DeWal (currently utilized by Morris-Shea). Different types of ACIP/AD pile installation equipment are shown in Figures 1 and 2. ACIP piles are installed into granular and cohesive soils, and soft rock to lengths currently approaching 130 ft (39.5 m), with diameters up to 24 to 36 inches (610 to 915 mm), and sustaining design loads approaching 900 kips (4000 kN). Current AD pile installation equipment in the United States is capable of installing up to 79-ft-long (24 m) piles with diameters ranging from 12 to 18 inches (305 mm to 460 mm).

Jan 1, 2002

By Alok Bhowmick

The most uncertain and challenging part of a bridge design and construction is the ‘Choice of foundation’. During the planning and conceptual design stage, it is extremely important to choose the right type of foundation. Wrong choice can lead to disaster for the project. This paper will present three interesting case studies of past bridge projects, to demonstrate how correct choice of foundation can help to meet the project commitments while the wrong choice of foundations can led to huge delay in project completion, leading to time and cost overrun.

Nov 1, 2022

By Donald Bruce, Alex Reeb, George Filz, Wesley Schmutzler, Mitsuo Nozu

"One million seven-hundred thousand cubic yards of deep mixing were installed to support an elevation raise of an earthen levee known as LPV 111, which is located in east New Orleans. The deep mixing was done by two contractors using somewhat different technologies, but producing elements of the same size. As part of the quality control and quality assurance program, 507 deep-mixed elements were cored and 5,082 specimens were strength tested in unconfined compression. This paper presents data from the coring and testing program. Very high percentages of the core run lengths were recovered, except during one period for one mixing technology. The coring methods are described, and reasons for the isolated episode of low recovery are discussed. The strength data show that the specification acceptance criteria were satisfied. Statistical parameters of the strength data are provided, and trends between strength and the following factors are discussed: depth, soil type, binder factor, and project-specific experience. Photographs of longitudinal cuts of core specimens are presented. Important lessons learned from this unusually large project are described.INTRODUCTIONThe Lake Pontchartrain and Vicinity Hurricane Protection system included a project known as LPV 111, which is an approximately 5-mile long segment of levee and floodwall located in east New Orleans along the Gulf Intracoastal Waterway and adjacent to Bayou Sauvage National Wildlife Refuge (Cali et al. 2012). The majority of the project consisted of a raise of an existing earthen levee from an existing crest elevation of about 18 ft to a new crest elevation of about 28 ft. The underlying soils were weak and compressible, providing inadequate support for the raised levee. Ground improvement in the form of deep mixing was selected to provide the necessary stability and settlement control for the raised levee.The US Army Corps of Engineers (USACE), New Orleans District, was the governmental agency in responsible charge of the project, including approval of design, construction, and payment. The lead designer was URS Corporation, and the general contractor was Archer-Western-Alberici (AWA), working in alliance with TREVIICOS South (Trevi), who, together with Fudo Construction (Fudo), performed the deep mixing.As part of the quality control and quality assurance program, over 500 production deep-mixed elements were cored, the cores were carefully logged, and over 5,000 unconfined compression tests were performed. In addition, selected specimens were carefully photographed before and after longitudinal saw cuts to expose the interior of the specimens. This paper provides a summary of the coring and testing performed on the production deep-mixed elements."

Jan 1, 2015

By Tracy Brettmann, Will Bohlen

An innovative retaining wall design consisting of tangent drilled shafts with supplementary seal piles was used to limit continuing bank erosion along the Brazos River in Southeast Texas. The riverbank erosion had progressed to where it was threatening the stability of both the bridge abutment and corresponding approach embankment of the heavily travelled Highway 99 bridge at this location. A tangent pile design was selected because it was both much faster to install and more cost effective than a secant pile system. The design included both 5.5-ft and 10-ft diameter shafts with depths up to 130-ft and comprised both anchored and cantilevered sections. Supplementary seal shafts were also installed between the structural tangent drilled shafts to help plug any gaps between the tangent shafts. The plumbness and diameter of the shafts were tested using a sonic caliper to make sure the shafts were installed within the specified tolerance. The initial design had to be revised when a record flood from Hurricane Harvey impacted the site during construction. Introduction The Fort Bend Grand Parkway Toll Road Authority (Owner) needed to protect the north bridge abutment with a retaining wall system due to rapidly eroding conditions of the Brazos River banks within the 300- feet-right-of-way of the State Highway 99 Jodie Stavinoha Bridge. The extent of the local scour and erosion along the north bank of the Brazos River has caused concern for the structural integrity of the bridge. The magnitude of the erosion along the north bank at the location of the bridge has been measured at about 120 feet over three recent hydrologic flood events locally referred to as Memorial Day 2015, Memorial Day 2016, and Tax Day 2016. During construction, a new record flood level occurred due to Hurricane Harvey in August of 2017 that resulted in a portion of the retaining wall needing to be redesigned due to even more erosion occurring. The Brazos River is an actively eroding and meandering alluvial river plain that naturally meanders and migrates over time. The processes of bank erosion and meander migration were ongoing before the bridge was constructed and will continue in the future. These recurring major flood events, however, rapidly increased the rate of erosion in just a few years. Background. Due to the need to protect the bridge as soon as possible, the Owner selected a project team consisting of the designer, general contractor and specialty deep foundation contractor prior to final design to work together in developing a cost-effective design that could be implemented rapidly. The project team initially considered both a secant pile and tangent pile retaining wall system using drilled shafts. After reviewing various alternative designs, a tangent pile wall with seal piles was selected based on both cost effectiveness and speed of installation. The tangent pile with seal pile option was approximately 20 percent lower in cost and 50 percent faster to install.

Jan 1, 2018

By Garland E. Likins

High-strain dynamic testing of drilled shafts and cast-in-place piles has become routine procedure in many parts of the world today. Field testing is performed by measuring strain and acceleration records under impact of a falling mass. Wave equation analysis is utilized to design the weight, drop height and cushion of the hammer apparatus to assure a successful test. The Pile Driving Analyzer* (PDA) and CAPWAP* methods are used for data acquisition and analysis. Testing results yield information regarding pile static bearing capacity, structural integrity, and pile-soil load transfer and pile load-movement relationships. This paper discusses application of high-strain dynamic testing to cast-in-place shafts with emphasis on aspects unique to this type of pile. Suggestions regarding minimum requirements for good quality tests are offered. Five case histories reported in the literature are summarized and a sample specification is also included.

Jan 1, 1995

By Robert Jakiel

The following paper is being presented to provide an understanding of the Deep Soil-Cement Mixing (DMM) performed at Contract C09A7 at the Fort Point Channel Site (FPC), for the I-90/I-93 Interchange of the Central Artery/Tunnel Project (CA/T), Boston, MA. The paper is written as a summary of the DMM from the DMM Contractor's perspective. The summary provides technical information and practical observations that are currently considered to be state-of-the art knowledge within the soil mixing industry. The observations and information are being provided by Robert L. Jakiel, Chief Engineer of SMW Seiko, Inc., who was the DMM Project Manager and Project Engineer for the A7 Joint Venture at FPC. The DMM was started in April of 1996 and completed in December 1999. The various acronyms and terminology used to describe the soil mixing are found in a section at the end of the paper.

Jan 1, 2000

By Eric M. Klein

As part of the Woodrow Wilson Replacement Bridge project several damaged wetland and environmental areas were to be mitigated. One of the mitigation projects consisted of constructing a Denil fish ladder around Peirce Mill Dam in Rock Creek National Park, Washington, D.C. The dam is a historic structure operated by the National Park Service. The fish ladder is located between the east abutment of the dam and Beach Drive, a major collector road. Construction of the fish ladder required removal of a portion of the east abutment and an excavation that extended about 22-ft below the pavement of Beach Ave. It was not possible to close Beach Drive except for very brief intervals or at night; therefore, a support of excavation system that would minimize disruption to the public was required. The high groundwater required that the groundwater be cut off prior to excavation; the random rubble and soil fill, and shallow but erratic rock surface precluded driving sheet piling. A jet grout system was selected because the grout probe could penetrate the rubble fill, stabilize a variety of soil conditions, and cut off the ground water prior to excavation. It was not possible to construct a stable wall without tiebacks or soil nails. Given the schedule and tight working conditions it was decided that soil nails through the jet grout wall facing would be the most cost effective method, as it did not reduce the working space as rakers would and would be more cost effective than prestressed tiebacks.

Jan 1, 2006

By Alan D. Fisher

Amtrak made a decision to replace an aging bascule bridge with a vertical lift bridge for their crossing of the Thames River in New London, Connecticut. The new lift bridge occupies the same alignment and shares the same foundations as the bascule span. During construction the deep foundation caisson supporting the bascule span settled and tilted. Investigation into possible reasons revealed interesting historical facts, both of the construction of the innovative open well caisson foundations and of the state-of-the-art in tremie concrete placing methods in use at the turn of the century. This paper describes both of these topics.

Jan 1, 2008

By Osamu Taki

The development of new auger bits for soil cement column drilling equipment has made it possible to create a homogeneous mixture of soil and cement-reagent slurry. As a result, soil-cement columns are used for foundations of houses and buildings, with reliable results, as demonstrated by many field projects and laboratory tests. This paper presents and discusses construction techniques for soil-cement columns, characteristics of the soil-cement solid, quality control, bearing test results, and soil-cement foundation design procedures.

Jan 1, 1992

By Christian Divis

[ ]

Jan 1, 2002

By T. Ruben

Micropiles have been used for the last forty years to strengthen building foundations. This article gives information about the technology and capacity of micropiles.

Jan 1, 2000