Search Documents

By T. Crivits, I. Bellemans, K. Verbeken

In the metallurgical industry, furnace cooling is often employed to enhance furnace lifetime. Hence, the pyrometallurgical phase comes in close contact with a non-air coolant. The proximity of the pyrometallurgical phases to the coolants may lead to dangerous situations. In case of a breach of the cooling circuit, the contact between a hot and a cold liquid may cause a vapour explosion. The outcome of this vapour explosion includes a pressure wave which could result in damage to the furnace, bodily injuries or even casualties. To prevent such dramatic events, the origin of vapour explosions is currently being studied in more detail. For this purpose, OpenFOAM was used to perform Computational Fluid Dynamics (CFD) simulations. In a first step, simulations were run to get a better idea of the influence of the compressibility on the simulations. The obtained results help in getting a better insight on the need of computational power, and possible numerical errors using compressible or incompressible solvers in future simulations. In a second step, systems without vapour explosions were simulated and compared to experimental results with mercury and aluminum. INTRODUCTION Humanity started using metals for tools around the Chalcolitic (~7400 cal BC), when copper was melted in small furnaces (Radivojevic, Rehren, Farid, Pernicka, & Camurcouglu, 2017). Nowadays, metallurgy has grown into a major industry and it has become impossible to imagine society without metals. In the pyrometallurgical industry, coolants (low temperature liquids, for example water) and pyrometallurgical phases (high temperature liquids, such as slags, mattes and alloys) are typically present in close proximity of each other. The interaction between these two phases can have catastrophic consequences (Tveit et al., 2008; Ferguson & Zsamboky, 2017). A vapour explosion may occur as the consequence of the rapid evaporation and expansion of the coolant. Whereas the volume of a gas increases linearly with the temperature (approximately a factor four by heating from 100°C to 1300°C), a simple calculation of the ratio of the two specific volumes shows that evaporation causes the volume of water to increase by a factor of 1700 at 100°C and ambient pressure (Table 1 and equation (1)), a number that was also found in literature (George, Nexhip, George-Kennedy, Foster, & Walton, 2006). The volume change occurs so fast that it resembles an explosion, hence the name vapour explosion. Such an explosion at industrial scale can cause economical losses, bodily injuries or even fatalities.

Jan 1, 2019

By A. Mular, T. Bond, G. D. Farnell, J. F. Kingston

"ABSTRACT:-A 60—cm semiautogenous grinding-(SAG) mill was designed -for continuous wet operation in closed circuit with a vibrating screen. The circuit is fully instrumented and automated. Part of the control system incorporates Foxboro SPEC 200 controllers around the pump box to maintain level. The rest of the control system involves an ACTION model BC2 basic direct digital controller that handles all other inputs/outputs and contact closure sensing:·The success of the control system is attributed to the uniqueness of specially designed mass flow metering systems. Various control strategies are possible. Employed to date has been control of a mill load set-point by cascading the deviation from load set-point as the set-point to the fresh feed rate ""controller"". Mill feed water is ratioed to total flow rate of solids fed to the mill. The performance of the circuit is being correlated with the performance of full scale SAG circuits in British Columbia to develop models, to assess the feasibility of scale up and to investigate the effects of design variables on responses such as circuit throughput. 1 INTRODUCTIONWhere ore types are appropriate, semiautogenous grinding and/or autogenous grinding (AG) has replaced conventional grinding. Secondary/Tertiary crushing plants are thereby eliminated so that capital expenditures are less and overall comminution costs can be lower (Barratt 1982). To establish the suitability of an ore for SAG circuits, pilot scale tests with 1.7 to 1.8 M diameter mills are often conducted. At least one test per ore type in a deposit has been necessary. Often, each test involves a large amount (up to 50 tonne) of sample, so that the testwork can be expensive and may discourage the use of SAG or AG circuits. However, MacPherson (1977) has employed a continuous 45 cm dry Aerofall mill circuit closed with screens and an air classifier to determine whether ores are suitable for SAG milling. The amount of sample per ore type is of the order of 60 kg or less. Thus an established SAG mill scale up procedure that employs small circuits is highly desirable.The purpose of this paper is to describe a small 60 cm wet continuous SAG/ AG mill pilot circuit assembled at the University of British Columbia to study the feasibility of scale up, to assess the influence of design variables, to develop mathematical models and to evaluate the effects of alternative control strategies on circuit performance"

Jan 1, 1988

By M. K. Walter

"The underground operations of Kidd Creek Mines uses an average of 450 U.S. gpm water during regular operations, and discharges an average of 800 U.S. gpm through consecutive staged pumping lifts of 1200f t.Water is used as a flushing medium for the drilling operations and as a dust suppressant for drawpoint mucking. The water retains an average of 5% suspended solids by weight which is removed underground before being pumped to the surface. This paper outlines the treatment of the mine water for the removal of suspended solids which are chemically treated to settle out as a sludge product of 60% solids by weight. This process reduces the sludge handling operation by 50%. The sludge is systematically disposed into the ore passes.IntroductionThe Kidd Creek minesite, located 27 km north of Timmins, Ontario, produces 4.5 million tonne s of copper, lead, zinc and silver ores annually from its No. I and No.2 underground mining operations. Both mines use a sublevel blasthole stoping method of extraction.Water from the underground operation passes through a series of surface settling ponds, where it is treated to remove heavy metal ions from solution. A blend of the pond effluent with fresh water from Kidd Creek, supply the underground with water at an average rate of 450 U.S. gpm. Water flows from the production zones through coarse sumps and into a main pumping station. There are five main pumping stations underground, three in No. I Mine and two in the No.2 Mine.The No. 2 Mine pumping stations are located on the 4800 level and the 3600 level. All water below the 3600 level to the shaft bottom is controlled from the 4800 pumping station. The water from the 4800 pumping section is combined with water from the remaining levels of the No.2 Mine at the 3600 pumping station. Water from the 3600 pumping station is pumped to the 2400 pumping station in No. I Mine.The No. I Mine pumping stations are located on 2800, 2400, and 1200 levels. All water below the 2400 level to the shaft bottom is controlled through the 2800 pumping station. This water is pumped to the 2400 pumping station. The 2400 pumping station also controls the water below 1600level to 2400 level."

Jan 1, 1988

By Gordon E. Agar

"The effectiveness of two this compounds for copper sulphide depression in molybdenite flotation has been examined with batch bench scale tests.Both thioglycollate and trithiocarbonate proved to be good depressants producing results similar to those f or cyanide and hydrosulphide. Ferrocyanide was ineffective on the samplematerial tested.The depressing effect of thioglycollate was readily reversed by an addition of xanthate.IntroductionThe separation of molybdenite from copper sulphide minerals has been practised for a long time(1,2). The predominant scheme is to depress the copper sulphides while capitalizing on the ready floatability of molybdenite to effect the separation. There are many recipes for depressing the copper minerals(3), among them the addition of sodium cyanide, particularly if the copper is present primarily as chalcopyrite; some form of sulphide whether as sodium sulphide, sodium hydrosulphide or phosphorous pentasulphide when there is a mixture of copper sulphides such as bornite, chalcocite and chalcopyrite; potassium ferro cyanide may be used when chalcocite is the principal copper sulphide; peroxide or hypochlorite; as well as heating in the presence of lime. There are different mechanisms by which these reagent s depress the copper sulphides. Sodium cyanide and the sulphide-producing compounds apparently reduce the potential of the copper sulphides to the point where they ar e rendered unfloatable by xanthates . Another study(4) showed that after cyanide addition, chalcopyrite was rendered un floatabl e until the REDOX potential (measured with a gold electrode with a saturated calomel reference) had become more positive than -250 mY. If the chalcopyrite pulp was conditioned after the cyanide addition the REDOX potential increased slowly, whereas if air was introduced during the conditioning the potential r ose much more rapidly. The difference in time to reach the desired level of - 250 mV was as much as 20 minutes' 25 minutes being required when air was absent but less than 5 minutes when air was admitted . These observation s demonstrate some of the problems encountered when using cyanide to depress sulphides such as chalcopyrite . The system adjusts to counteract the depressing effect of the additive. To overcome this tendency it is necessary to either add an overdose at the beginning or to more or less continuously add the regulating reagent. In this study cyanide solution was added under automatic control to maintain a specified REDOX potential."

Jan 1, 1984

By Orlando Rojas, Javier Pizarro, Romke Kuyvenhoven, Francisco Soto

"The concept of geometallurgy has been extensively mentioned and used in the mining industry in the past years. However, each mining firm has a different understanding of what geometallurgy means, and its actual value varies significantly from site to site. Even in the case of properly constructed geometallurgical models, it is fairly common to observe a sub-utilization of the model in the actual operation, because of its low production forecasting capability on the short term. This disconnect between the geometallurgical model and operations is typically caused by a lack of tuning between the original model and the actual plant operation. Also, the absence of procedures and other standards for reconciliation, affects the confidence and the predictive quality of the model. The geometallurgical model should consist of three different levels: (I) adequate capture of information, (II) data analysis and modelling, and (III) development of the block model. Once the geometallurgical in-situ model is finalized, a process model should be developed of the plant at industrial scale, in order to scale up the in-situ geometallurgical parameters from their base or standard condition, to the actual operating reality of the plant. Finally, the stage of reconciliation will close this process, assuring that any deviation between the geometallurgical model and the actual plant operation is not due to lack of tuning, but due to operational issues such as unattended maintenance requirements or poor process control in the operation. The methodology as described in this paper has been applied at several large mining sites in Chile. The paper presents the characteristics of the proposed methodology, and quantitatively describes its benefits with examples from actual operations.INTRODUCTIONIt probably is fair to say that geometallurgy became widely used in greenfield projects in the Andes region during the mining boom of the 90’s, when massive orebodies were studied and developed, and upfront metallurgical characterisation proved its use for accurate economic evaluation including estimates of plant throughput, energy consumption, final product quality and overall recovery. A few examples of such greenfield studies for concentrator plants in the 90’s are Minera Los Pelambres (Antofagasta Minerals, Chile), Minera Escondida, Laguna Seca (BHP Billiton, Chile), and Rio Blanco (then Montterrico Metals, Peru). Large size hydrometallurgical operations such as Cerro Colorado, Quebrada Blanca and Lomas Bayas (all in Chile), also recognised early on the importance and value of relating ore mineralogy, geological characterisation and metallurgical behaviour."

Jan 1, 2016

By D. L. Mckay

"Texasgulf's 25-foot-diameter Kidd Creek No. 2 Shaft is situated next to the company's No .1 Shaft, so that both shafts can share common surface and underground facilities. Shaft construction, covering a span of five years from collaring to commissioning , started by freezing the 50 feet of grey varved clay covering the bedrock. After first completing the concrete headframe, sinking to the 5/00-foot horizon utilized two different shaft construction methods. The top 2800 feet was excavated by slashing a 6-foot-diameter borehole and hoisting the broken material up the 3OO0-foot-deep No.1 Shaft; the remaining 2300 feet was excavated by conventional benching methods. Prior to installing the 5100 tons of galvanized shaft steel on the completion of the sinking operation, the sinker was able to install all thirteen armoured electrical cables in one pass with his modified galloway stage. All loading and lip pockets were installed along with the steel guides and bun tons during the equipping operation.IntroductionOn November 21,1978, Texasgulf completed the No.2 Shaft at Kidd Creek Mine. This shaft is the largest shaft (volumewise) in North America and is unique in many respects . The purpose of this paper is to outline some of the unique features of this shaft as well as to record how this facility was constructed.Soon after sinking No.1 Shaft, Texasgulf started a program of exploratory diamond drilling from the 2800 level in No. 1 Mine. The drilling outlined sufficient ore below that level to justify a second mine. Feasibility studies demonstrated that production could be increased by one-third exclusively from this deep ore . The study called for a 25-foot-diameter shaft to the 5100-foot horizon to service a mine producing 5,000 tons of ore per working day.The site chosen for No.2 Shaft and head frame is 350 feet southwest of No.1 Shaft. This, along with No.1 Shaft, will be away from the influence of ground subsidence when mining at depth. The collar and head frame foundations are located on a flat rock ledge some 70 feet below surface. This flat ledge was found by test holing through the overburden by diamond drilling. It is fortunate that this location best satisfied the surface layout and logistics for both surface and underground ore and waste handling."

Jan 1, 1981

By Gerardo Fuentes

Arsenic extraction from Chilean copper concentrates up to nearly 99% was achieved, using hydrothermal reactions. Arsenic appears in nature in more than 200 mineral species, being arsenopyrite (FeAsS), enargite (Cu3AsS4), and tennantite (Cu12As4S13) the most common species. In addition, arsenic is present in a large amount of copper concentrates, produced in northern Chile. Medical statistics show that in northern Chile, the amount of cancer to the lung, skin and bladder are the highest in the country. The latter situation, demonstrates the importance of studying metallurgical processes that do not generate atmospheric pollution. The hydrometallurgical processes such as hydrothermal treatment in autoclave reactors, do not produce gaseous emissions. On the other hand, the arsenic remains in solution from where it can be transformed in scorodite by widely known methods. Previous works about hydrothermal treatment of enargite have shown the feasibility of transforming the enargite of the copper concentrates into chalcocite or mineral species of the chalcocite family such as djurleite, digenite and for this reason enrich the concentrate in copper and pass the arsenic to solution. For this research, two Chilean copper concentrates were used, concentrate 1 with 5.5% arsenic and concentrate 3 with 1.8% arsenic. These concentrates were subjected to a complete chemical and mineralogical characterization. Later these concentrates were carry out to batch tests of hydrothermal treatment. Also, these concentrates were subjected to grinding to have different particle sizes. For the hydrothermal tests, a liter capacity Autoclave Engineer reactor was used. Characteristic of this reactor was the maximum temperature 350°C, 5000 PSI pressure, and 900 rpm agitation speed. Kinetic tests were carried out with the two concentrates maintaining the same solid: liquid relationship, the same agitation velocity and the variables studied were treatment temperature, time of reaction, concentration of copper in the solution and grain size of the concentrates. The conclusions of the study indicated arsenic extraction of the order of 93.98% from the concentrate 1 and arsenic extraction of the order of 98.74% from concentrate 3. After the hydrothermal treatment, the solids and solutions were characterized chemically, by electron microscopy and X ray diffraction. Also the solids were characterized by grainsize through a particle size analyzer (MICROTRAC). Results of batch treatment shows that arsenic can be release almost completely from real copper concentrates using this hydrothermal process and the next stage will be a scale up process in order obtain results for pilot plant design. INTRODUCTION Arsenic is an impurity that appears associated with copper minerals forming enargite, tennantite, tetrahedrite, and that due to the pyrometallurgical treatment either in conversion or roasting furnaces, it goes into the atmosphere together with the sulfur dioxide. A great quantity of literature can be found to eliminate arsenic or try to separate arsenic from copper. The methods used are mainly leaching processes with or without pressure (Padilla, Jerez & Ruiz, 2015) with different reagents like chloride media (Herreros, Fuentes, Quiroz & Viñals, 2003) or chloride media with sulphuric acid (Riveros & Dutrizac, 2008) or sodium hypochlorite (Mihajlovic, Strbac, Zivkovic, Kovacevic & Stehernik, 2007). It is known too that Chile is the first copper producer in the world and a great quantity of its minerals are in the north of the country, in Antofagasta.

Jan 1, 2019

By Aleksandar N. Nikoloski, Tendekayi Tapera, Glen P. O’Malley

Chalcopyrite (CuFeS2) and enargite (Cu3AsS4) are among the most important copper sulfides. At present, many known deposits of these minerals are uneconomic to process because they are of too low grade, insufficient size or too remote to be cost effectively treated with conventional technologies that can deal with their refractory nature. Therefore, developing an effective, low cost extraction process for recovery of copper from them is important. The research presented in this paper will deal with potentially cost effective strategies involving catalysed processing, studied under conditions relevant to recycle heap leach conditions. The present account summarises some of the main findings from the research program carried out at Murdoch University between 2014 and 2018 that has investigated the effects of the common leaching parameters, major and minor species present in the leach system and additives on the rate and extent of copper extraction from low-grade ores, in which primary copper sulfide minerals such as chalcopyrite and enargite were the dominant copper minerals. The study involved batch leaching tests, detailed structural and mineralogical characterisation and thermochemical modelling under conditions relevant to heap leaching. The results have demonstrated that silver in particular has a strong catalysing effect on the extraction of copper from ore under the leach recycle conditions and, at an adequate dosage, can effectively overcome surface passivation, enabling almost complete extraction of copper from chalcopyrite as well as enargite. The aim of this paper is to present the effect of the studied additives and to briefly elaborate on the mechanism of the silver catalysed leaching process. In addition, the presence of certain secondary agents was shown to lower the critical dosage of silver and promote extraction. The data from the study allowed the development of a theory for the silver catalysed reaction mechanism, which enables further optimisation and cost-effective application of this strategy in practice. INTRODUCTION Researching the extraction of copper from chalcopyrite is important as it is the most abundant copper mineral in the earth’s crust. The majority of ores containing this mineral are processed by flotation to produce a concentrate, followed by smelting and electrorefining. However, most reserves available nowadays are of low grade or limited in size, and therefore not suitable for this conventional approach. Hydrometallurgical processing via heap leaching with or without the aid of bacteria has been shown to be potentially economical. Chalcopyrite is refractory though and suffers from slow leaching kinetics and poor overall extraction, so understanding the mechanism of how it leaches has received significant attention by researchers working in this field over the past 50 years. The refractoriness, which is the main issue with the hydrometallurgical approach, is generally described as passivation of the chalcopyrite surface whereby a surface coating is formed that blocks the reaction interface or wetting of the chalcopyrite, limiting the copper extraction. Exactly what this layer is made of or how the issue could be overcome has been the subject of intense study and debate for many years. One of the limitations of the work to date is that much of the research focus has been on typical initial leaching conditions, while there has been relatively little research into how the leaching is affected under recycle solution conditions where certain metal ions (Fe, Mg, Al) have often accumulated in the liquor. This occurs because the leach solution exiting a heap contains many species from the dissolution of gangue minerals and typically this solution is returned to irrigate the heap, once the copper has been removed, leading to an accumulation of these species.

Jan 1, 2019

By M. Niinae, F. Nakahara, T. Kawamoto, T. Suzuki

"MgO was chosen as an As(V) immobilization agent and a series of immobilization experiments was performed to obtain insights into the behavior of As(V)and MgO during leaching tests. Our experimental and modeling results demonstrated that As(V) immobilization by MgO consists of the following steps: (i) an increase in soil pH, (ii) desorption of As(V) from the soil, and (iii) the re-immobilization of As(V) by MgO/Mg(OH)2particles. Regarding the behavior of MgO, the modeling results showed that when the MgO dosage was 25 mg MgO/4g-drysoilor less, the majority of MgO was used to increase pH, and less than 1% of MgO was used to sorb As(V), which was consistent with the result of leaching tests showing that a high level of As(V) was leached at the MgO dosages. On the other hand, when the MgO dosage was above 25 mg MgO/4g-drysoil, the percentage of MgO used for As(V) sorption increased up to 35%, and correspondingly, the As(V) leaching level decreased to below 0.01 mg/L As at an MgO dosage of 75 mg MgO/4g-drysoil.INTRODUCTIONOne of the major arsenictransport pathways causing groundwater contamination is the migration of arsenicfrom artificially or naturally contaminated surface soils. Therefore, in this study, the immobilization of arsenate (As(V)) in soils was investigated using commercial-grade magnesium oxide (MgO) as a potential cost-effective measurement to prevent the occurrence of groundwater contamination with As(V).With respect to the use of MgO for remediating As(V)-contaminated environmental media, MgO has been used in several studies to remove As(V)from water(Yu et al., 2011; Jia et al., 2013; Tresintsi et al., 2014). Although these studies demonstrated that MgO effectively removes As(V)from water in water-MgO systems, the behavior of As(V)in water-soil-MgO systems has not been evaluated in the literature, and several questions remain to be answered to comprehensively evaluate the use of MgO as an As(V)immobilization agent in soils. For instance, as is well-documented in the literature(Ford, 2002; Lenoble et al., 2002; Zeng et al., 2008), iron oxy-hydroxide (FeOOH) is one of the important adsorbents for As(V)in both natural and engineered systems. Therefore, it is anticipated that the presence of FeOOH in soils significantly influences the behavior of As(V)in water-soil-MgO systems and consequently, the immobilization performance by MgO. Another important question to be answered is the behavior of MgO during the immobilization treatment. In our previous studies (Suzuki et al., 2013a, 2013b), commercial-grade MgO was demonstrated to effectively immobilize lead and fluoride, and the immobilization effectiveness was indicated to last more than 100 years against the exposure to acid rain (pH 4.0). However, these studies focused on the behavior of contaminants. As a result, little is known about the behavior of MgO during the immobilization treatment. The lack of understanding of the behavior of MgO during immobilization treatment is one of the main concerns leading to relatively low public confidence in immobilization treatments."

Jan 1, 2016

By G. R. Davidge

"Falconbridge Mine has a history of significant microseismic activity dating back to 1955. Since mid-1981, a microseismic monitoring system has been operating in the area around the No .9 Shaft hoist room located 25 m from the are zone at a depth of 1200m. Several mine wide faults dissect this area and have been shown to be microseismic-active due to mining. The microseismic monitor has been interfaced with a small dedicated personal computer and a communications device to perform routine data evaluation and to produce graphical output. The programs are described and selected result s from the monitoring program are presented.IntroductionFalconbridge Mine is located on the southeast rim of the Sudbury Basin. The nickel-copper sulphide ore zone is essentially a tabular orebody striking approximately east-west and dipping at 80 degrees north near surface and rolling to 75 degrees to 80 degree s south by the 1000 level. (Mine level number s represent the approximate depth in feet below ground surface .) This dip is maintained down to the 6000 level. The north wall is comprised of jointed norite and a faulted contact up to 1 m thick exists between the ore zone and the norite. The south wall rock is a greenstone with highly siliceous lenses and often has a faulted contact with the ore zone. No less than five mine wide faults exist, as shown in Fig. I.Mining ha s been carried out from virtually the bedrock contact to depths of 1830 m although the majority of current activity is between 900 and 1500 m below surface. A winze provides access below the 4025 level and the cage hoist room is located on the 3850 level in the north wall 25 m from the contact. Because of concern for the stability of this hoist room, there has been no mining activity within 60 m of the hoist room and by 1980 this block of ore was one of the major blocks of high-grade ore remaining in the mine . Mining of this block was originally scheduled for very late in the decade.Prior to a six-month shutdown in 1982, this mine produced approximately 450,000 tonnes of ore annually, mainly by cut and- fill techniques. Following the shutdown, annual production has been reduced to approximately 200,000 tonnes and production is now mainly by undercut and fill techniques .Mining-induced seismicity has occurred at Falconbridge Mine since at least 1955 and reviews of the microseismic problems for the periods from 1965 - 1970 and from 1971 to 1979 were made by Singh (1971) and Vongpaisal et al. (1980), respectively. The need for instrumentation was addressed by these authors. Following several large events during the spring of 1980, a decision was made to investigate existing microseismic monitors and to apply micro seismic monitoring techniques in Falconbridge Mine. Application of microseismic monitoring to Falconbridge Mine was to concentrate on the No . 9 Shaft hoist room area of the mine, particularly around the 4025 level where a large mechanized cut-and- fill stope was approaching this level. By mid - 1981, the microseismic monitor was fully installed and with in a year , a short-period seismograph and a personal computer had been added to the system."

Jan 1, 1984

The article presents an outline of methods and certain results of laboratory tests, underground tests and model tests, aimed at assessing performance of a powered shield support on the floor of low strength parameters. The tests were conducted within the framework of GEOSOFT project co financed by Research Fund for Coal and Steel (RFCR-CT-2010-00001). The described research works were conducted by Central Mining Institute (Glówny Instytut Górnictwa), Janina coal mine and Becker-Warkop

Aug 1, 2013

By Anthony P. Makuch

Dynatec Corporation is an integrated mining services company, providing mine development, operations management, engineering, drilling and metallurgical services to the North American mining industry. Dynatec was the contract operator of the Ken Snyder Mine in Midas, Nevada from start of production in January 1999 to September 2001. This paper summarizes Dynatec?s experience and approach to the use of longhole stoping methods for mining to widths of 1.3 to 2 metres in a steeply dipping narrow vein orebody.

Oct 1, 2001

By James Stenhouse

Abstract The aqueous oxidation of pyrite in caustic solutions under oxygen pressure was investigated by measuring that effect of reaction variable on oxygen consumption by the reactions. From the results of this investigation, a model for the process has been proposed. In this model, sulphur diffuses as a positive ion through an oxide layer which forms on the sulphide particles and is then oxidized to sulphate ion. Iron is oxidized by substitutional diffusion of oxygen atoms into the oxide layer. The effect of most reaction variables on the rate of oxygen consumption can be explained with this model. Introduction Recent investigations (1,2,3) have shown that certain sulphide ores can be readily leached by agitating the ore in the form of a pulp under pressure in the presence of oxygen. Since very little was known of the mechanism of this oxidation, a programme of investigation was inaugurated in 1949 in the laboratories of the Department of Mining and Metallurgy of the University of British Columbia. Financial support for the investigation was received from the National Research Council in the form of student grants and bursaries, from the Canadian Liquid Air Company, Limited, and from the Consolidated Mining and Smelting Company of Canada, Limited. The first objective was to devise a technique to study the primary oxidation reactions in aqueous solutions and to apply the technique to a detailed study of the oxidation of pyrite in caustic solutions.

Jan 1, 1952

By C. -K. Fang, T. H. Chuang

"Temperature effects on the erosion of the 6063 aluminum alloy were investigated. Erosion experiments were performed by sandblasting silicon carbide particles of 80 grit size. The target volume loss, and worn depths of the eroded material were investigated at different temperatures. It was found that the temperature had only a minor impact on the peak attack angle. The effect of temperature on erosion damage depended on the relative humidity (RH) of the environment. IntroductionThe synergy of wind and sand or dust may result in the erosion of materials. However, the severity of erosion damage in different areas and in different seasons might be varied, depending on environmental variables such as temperature and humidity. As a result, determining the effect of environmental variables on erosion damage is important in selecting or ranking materials for their suitable applications in diverse areas.The relationship between erosion wastage and temperature is governed by many factors including temperature dependent properties of the material (strength, ductility, toughness, and dynamic hardness, etc.), mechanical erosion characteristics, the rate of oxidation, and the mechanical properties of oxides. Although the effect of temperature on erosion has been studied for engineering materials (Smeltzer et al., 1970; Gat and Tabakoff, 1978; 1980; Levy et al., 1986; Levy and Man, 1986; Chinnadurai and Bahadur, 1995; Howard and Ball, 1997; Colclough and Yeomans, 1997; Suckling and Allen, 1997), published literature dealing with aluminum alloy is rather limited."

Jan 1, 2000

By G. G. Campbell

"HistoricalBARYTES was mined in Nova Scotia as early as 1874 from a deposit at Five Islands, on the north shore of Minas Basin. The first record of the presence of the mineral at the Walton site appears in a report by Selwyn in l893, who states: ""Barytes in considerable quantity occurs in veins in lime-stones at Walton and Pembroke"". The exact site of the present workings was marked •on a map published by Fletcher in 1905.The economic •possibilities of this deposit, however, were not recognized until 1940, at which time we were at war with Germany, who up to that time had supplied 50 per cent of the world's requirements.At that time the Nova Scotia Department of Mines, recognizing the need for certain strategic minerals, induced Canadian Industrial Minerals, Limited, to send prospectors into 'the area to look for manganese. No manganese deposits were found, but a deposit of barytes was directed to their attention, and exploration and development work on the occurrence was proceeded with.IntroductionThe south shore of Minas Basin between the Avon river at Windsor and the Stewiacke river at Maitland has long been known as a potential source of mineral wealth. It had attracted the attention of mineralogists and in the past had produced considerable tonnages of manganese ore and gypsum. Depletion of ore in surface and near surface deposits resulted in a dwindling production, until today only deposits of gypsum are worked."

Jan 1, 1952

By J. I. Jr. Moore

Many articles have been written about the various operations of Britannia mines and mill, as well as treatises on the geology and ore deposits. A partial list of these papers is given below. Most of these papers have covered well the history of Britannia, and have included a thorough discussion of the geology and ore deposits; therefore, in this paper, no account of these subjects. is necessary. However, a short description of the ore deposits will be given as an aid to a clear understanding of the descriptions of the various mining methods. The Ore Deposits The ore deposits at Britannia occur along a shear zone and are five in number, named for the claims in which they lie, as follows: Jane, Bluff, Fairview, Empress, and Victoria. Each of these deposits is called a mine, as they are separated by 500 to 1,000 feet of barren ground. The Jane mine, although the first producer of the Britannia group, has not been in operation for a number of years. The deposit is a silicified replacement in sediments; with very little evidence of shearing. The Bluff deposit is a highly silicified replacement in porphyry, massive and irregular, very hard in the upper 600 feet with practically no shearing, and softer within chlorite schist in its lower 1,000 feet . The Fairview deposit consists of a series of twelve distinct veins or lodes, rather lenticular in shape, and occasionally merging.

Jan 1, 1928

By M. Piard

The scarcity of literature referring to mines in the Rockies has compelled the writer to co-ordinate information and advice taken at the very source. Help was gladly given by active inspectors and mine bosses. Although the field is unimportant at the present time, due to its distance from markets for raw coal, it is quite worthy of the attention it is receiving from two continents; for, with the commercial synthesis of liquid fuels, it would become the largest fuel laboratory in the world, provided, of course, that freight cost drops to a low comparative level. As explained below, there are no obstacles to economical and safe operation under anything like the typical outcrop shown in Figure 1. Although coal dust is probably more dangerous in the Rockies than anywhere else, the damp outcrops afford means of control. The abundant gas may be bled to the open air, and the rigid roof will settle gradually under a wide span of opened outcropping. The Panel Retreating Wall The Measures: Coal measures having an attitude similar to that shown in cross-section in Figure x are characteristic of the active coalfield on the Alberta side of the Rockies, and they are also found on large tracts of undeveloped land west of the divide. The small anticlines, not shown in the cross-section, do not affect the progress of a pillar line, provided their crests are connected to the atmosphere by drainage bore-holes.

Jan 1, 1928

By M. H. Ali

Codelco, a multi-process primary copper producer, is undertaking a full life cycle inventory (LCI) of all its commercial products based on copper and molybdenum. During this work, many questions have surfaced regarding the contribution of process unit design to specific aspects of a product's LCI and, more importantly, how such designs could be improved using a life cycle perspective. Management strategy efforts were undertaken to improve the LCI footprint, however it was found that the corrective actions were almost impossible to apply at the operation level in plant, given the ongoing timing pressures of extractive mining, and costs saving priorities. Additionally, it was found that most of the important comparative differences between operations had structural reasons. In this circumstance, the LCI practitioner group from 1M2, and the environmental managers from Codelco, decided to shift its efforts to place the critical LC1 aspects to the design process of future developments. Hatch Associates has developed unique tools in their Sustainable Plant Design (SPD) package that compliment and enhance LCA methods; these effectively drive sustainability into the heart of the design process. By using LCA and SPD in a project design phase, you cannot only address potential hotspots, but also decide on materials, location and size of certain facilities to optimize for energy efficiency. Moreover, you can avoid the shifting of environmental burdens upstream or downstream within the plant and finally it is extremely useful in identifying opportunities for greenhouse gas reduction.

Jan 1, 2007

By P. Fleming, W. Pascheto

"Rod mills processing nickel and copper ore experienced recurring failures of liner bolts. In some cases failures became very frequent, requiring constant mill intervention and consequently impacting process stability and operating costs. Investigation related to the causes of bolt failures involved a multidisciplinary approach with the participation of engineering, maintenance and operation. It included the determination of bolt failure mechanisms as well as the assessment of mechanical properties, fabrication quality and handling and installation procedures. In addition, other parameters affecting bolt performance such as mill and liner design, operating parameters and maintenance practices were studied. This paper reports the failure investigation results and proposed solutions for failure prevention. INTRODUCTIONOccasional liner bolt failures are common in rod mills. However, chronic bolt failures developed in rod mills processing nickel and copper ore caused frequent shutdowns for bolt replacement to an extent that affected process stability. At first, it was thought that the cause of recurring failures was related to bolt quality. The operation then submitted several failed bolts to failure analysis. However, it became apparent that bolt quality was unlikely to be the main cause of failures. The determination of root cause (s) then became more complex, requiring a multi-disciplinary approach to failure investigation, requiring the assessment of bolt installation methods, mill design, operating conditions and maintenance practices. The results of the metallurgical failure analysis and investigation of other possible causes of failures are reported here."

Jan 1, 2016

By J. C. Glandus, N. Tessier-Doyen, M. Huger

The Young's modulus of bi-phased model materials (vitreous matrix containing spherical alumina inclusions) have been determined by two complementary approaches: experimental and analytical. If the matrix and inclusions exhibit close coefficients of thermal expansion, the experimental results lie in the vicinity of the lower bound of the Hashin & Shtrikman's model. If there is a dilatometric disagreement between the components, untypical behaviors, similar to those obtained for a family of industrial refractory materials, were observed when the temperature varies.

Jan 1, 2004