Search Documents

"The ore currently being milled at Delnite is a high pyrrhotite ore with the gold intimately associated with the pyrrhotite. To get maximum recovery of the gold with the lowest reagent cost, it is necessary to keep the pH as low as possible In the laboratory the best results were obtained with a pH of 10 but in the plant it was found that a pH of 11 was the minimum practical pH. With the n1anual control it was difficult to maintain this figure.The Mines Branch had a conductivity probe (see Fig. 1), developed by Dr. G .G. Eichholz that they wished to try out in plant operation.On June 17, 1963, the probe with all necessary control equipment was installed in the regrind circuit (see Fig. 2) at Delnite Mines. Crushed quick lime is fed at this point but it is also necessary to feed hydrated li1ne at two other points in the cyanide circuit in order to maintain the pH close to 11. 0 throughout the circuit. Only the feeding of the quick lime at the regrind mill was controlled in this test.One thing that concerned me with the operation of the probe was whether the reading on the probe chart would correspond to the pH. A look at the graph accompanying this paper will show that except for very minor variations the graphs of the chart reading and the pH reading are parallel. The upper graph shows that the pH reading and the lime titrations also correspond and that the cyanide titrations appear to have little effect on the pH reading.Table 1 gives the results obtained for the two months before and after the instal1ation of automatic control as well as the two months of control. Unfortunately there was a decided change in ore just after the automatic controls were removed. There was much less pyrrhotitc in the ore than usual thus changing the need for lime and cyanide."

Jan 1, 1964

By W. A. Grell

"The oxygen meter has been in use at MacLeod Cockshutt Gold Mines for over a year, At MacLeod about 200 tons per day of reground concentrate containing roughly 10% pyrrhotite and 20% pyrite is cyanided in four 181 x 18' Dorr agitators. A survey by the Department of Mines showed that oxygen content of some of the agitators was rather low. Experience with our oxygen meter indicates that the oxygen content must at times have been too low for good gold dis solution.We have found that in winter, when pulp temperatures drop to about 50° F, oxygen saturation in the agitators is not difficult to maintain. In summer, however, when pulp temperatures rise to 70or 75°F, the oxygen content will drop very readily. It was found that a high oxygen content can be maintained readily if the pulp is sufficiently dilute. Thus at 50° F, a pulp of specific gravity 1. 75 i.e., about 55% solids, will saturate; but at 70 or 75° F, the specific gravity must be decreased to 1 .45, equivalent to about 40% solids, in order to maintain saturation. Very thick pulps, such as thickener underflows, are noticeably difficult to saturate in the laboratory, and lose their oxygen rapidly.Clear solutions, on the other hand, absorb oxygen readily and hold it. The primary thickener overflow, before agitation, is 100% saturated; after storage of 3 to 4 hours it is still 100% saturated at re clarifier tank. Barren solution after spraying in a launder is 100% saturated.We have not yet attempted to determine what percentage saturation is necessary for good extraction, but it is known that there is a point at which extraction decreases rapidly. So far, the measures required to maintain over 80 or 90% saturation have coincided with measures required to hold the reducing power to the point believed necessary."

Jan 1, 1964

By A. Fyson, M. P. Smith, Margarete Kalin

"Drums containing 0.07 m3 of pyritic waste rock from a zinc/copper mine, with and without Natural Phosphate Rock (NPR) additions (40 kg/t waste rock) were set up outdoors. The effluent chemistry has been monitored over a period of 709 days. In the presence of NPR, the cumulative acidity discharged from 7 out of 8 drums was 80 % less than that discharged from drums without NPR. Mixing NPR throughout the drums was more effective in reducing acidity than placement of the NPR in a layer in the drum. NPR treatment was more effective for 'fresh' waste rock than for material which had weathered for more than 4 years. It is concluded that application of NPR to pyritic waste rock could greatly reduce acidity generated.IntroductionWaste rock dumps are significant sources of acid, generated by the oxidation of sulphides. Oxygen and water supply are oxidation rate-controlling factors, and oxygen supply is the reaction-limiting component. If secondary minerals can be formed on the surface of the rocks, pyrite oxidation and therefore acid generation may be reduced or inhibited. Neutralizing agents such as limestone do not prevent the oxidation of pyrite but treat the resultant acid mine drainage (AMD) or acid rock drainage (ARD).Meek et al. (1991) determined in pilot scale experiments that apatite mixed with tailings was more cost effective than liming or use of PVC liners to reduce oxygen and water penetration into the tailings. Phosphate is not acting as a neutralising agent but it creates a chemical condition on pyritic surfaces which prevents reactions of the oxidising agents. Precipitation of principally iron phosphates physically isolates the pyrite surfaces from further oxidation (Ziemkiewicz 1990; Evangelou 1994). The chemistry of the phosphate effects has been described by Spotts and Dollhopf (1990). Secondary mineral formation was evident in the leach pile at Gibraltar when leaching was impaired (Scott, 1991) indicating a link between oxidation and the mineral-formation process. This paper reports on effluent characteristics when waste rock is generating acid in the presence of NPR."

Jan 1, 1995

By E. G. Joe

"The continuing increase in costs for power and fuel are affecting significantly the cost for milling of Canadian ores. In order to ascertain the scope and source of energy consumption in Canadian mills for further energy conservation opportunities, CANMET, in cooperation with the Canadian Mineral Processors carried out a detailed survey on the metallic mineral processing plants. Sixty-seven mills representing almost 300 million tons of annual capacity participated in the survey. The results indicated that in general, copper and iron ore mills, representing the bulk of the tonnage, consumed relatively low levels of energy per ton. Nickel-copper, zinc-copper and lead-zinc ore mills were moderate in energy consumption, while uranium and some copper-lead-zinc mills reported much higher energy consumptions due primarily to the increased heat requirements of the ore pulp. While the plant heating costs varied somewhat with the location in Canada, it was apparent that the lowest heating costs were achieved by those built with proper insulation and energy conservation design. If the cost per million British Thermal Units is taken as $2.00, the mill energy costs generally ranged from 40¢/ton up to $1.20/ton.IntroductionEnergy consumption in milling has always been of significant interest to Canadian mineral processors who traditionally calculate their milling costs down to pennies per ton. Even the measure of an ore's grindability is expressed empirically by Bond in kilowatts hours per ton milled. Some of the mills located in isolated areas were obliged to generate their own electrical energy from fossil or petroleum-based fuel at a cost substantially higher than that obtainable from captive or public hydro-electric installations. These mills practiced energy conservation long before the advent of O.P.E.C. energy cost inflation. One example of this was the use of electric boilers to produce process and heating steam during off-peak electrical load periods."

Jan 1, 1978

By R. J. McLeod

"Grinding at Giant Yellowknife is done in two stages. The first stage consists of two ball mills in closed circuit will: mechanical classifiers, the classifier overflow goes to flotation. The tailings from this flotation circuit are separated into slime and sand portions, the slimes go to an additional flotation circuit while the sand portion goes to the secondary grinding mills.Milltronic automatic sound control units were installed on each of the two primary ball mills and put into operation September 3, 1966. After about two months adjustments to the control units the operators were taken off the grinding circuit on November 1, 1966. The operators duties were taken over by the automatic control units while miscellaneous work was taken over by the helpers in the mill. The labour saving by the installation is approximately $2250.00 per month.After a short period of operation it was apparent there was a slight change in grind. The screen analysis of the primary classifier overflows for the period May to August 1966 averaged 62.23% minus 200 mesh while for the period September to December 1966 averaged 62.0% minus 200 mesh. This is a slight coarsening of the grind. The change in the primary grind has manifested itself also in the screen analysis of the final grind. Before automation the final grind was 80% minus 200 mesh, while after automation it was 7 5% minus 200 mesh. A change of grind was also noted in the flotation concentrates. Before automation the screen analysis of the concentrates was 35% plus 200 mesh and 50% minus 3 25 mesh. A ft er automation it was 35% plus 200 mesh and 47 .5% minus 325 mesh. In other words the grind got coarser or perhaps we should say there was less overgrinding. Another significant change took place in the assays of the slime and sand portion of the primary flotation tailings. It was usual under manual control for the slime portion to assay higher in gold than the sand portion. The reverse is now true."

Jan 1, 1967

By Samantha A. Beeson, Colin Poole

"A selective flocculation-floe flotation technique is already in use in the Canadian potash industry for the removal of water-insoluble slimes, but the process is currently limited in its application and reagent consumption is high. The work described in this paper details investigations into the separation of sylvite and halite from water-insoluble slimes by selective flocculation utilising other commercially available polymers.Preliminary flocculation performance tests were undertaken on pure sylvite, halite and water-insoluble minerals to establish the importance of a number of experimental parameters. The data from these single mineral tests was then used to establish optimum parameters for the separation of sylvite and halite from a synthetic mixture similar in composition to a typical potash ore. Under optimum conditions, separation was achieved with high recoveries using dispersant and flocculant dosages significantly lower than those currently used in plant practice.IntroductionAlthough solar evaporation and solution mining are used in some operations, most potash is extracted by conventional underground techniques and is then processed by froth flotation, in order to separate the valuable sylvite (KCI) from halite (NaCl) and water-insoluble gangue minerals. Flotation is usually preceded by a desliming stage to remove water-insoluble fines, but this also results in high potash losses and affects process brine requirements. To overcome these problems, one plant operated by Cominco in Saskatchewan uses a selective flocculation -floe flotation process (Banks, 1979/1980), in which a polyacrylamide flocculant is added to produce floes of water-insoluble material with minimal incorporation of halides. A collector is then added to render the floes hydrophobic and suitable for removal by froth flotation.A number of workers have also investigated the use of selective flocculation in potash processing, but these too have been concerned with developments in the removal of water-insoluble slimes (Williams, 1960; Brogiotti et al, 1974; Chan et al, 1986; Thompson et al, 1979; etc.). This paper provides results of novel investigations into the selective flocculation of sylvite and halite from water-insoluble minerals and discusses the possible mechanisms involved."

Jan 1, 1995

By M. Remillard, M. Garon, M. Thérien, D. Hodouin

"Nineteen streams in the copper and zinc flotation units of the concentrator of the Matagami division of Noranda Inc. have been sampled for particle size distributions chemical assays, and gold and silver contents in each particle size interval. The data are upgraded by the mass balance package BILMAT. These results, in conjunction with microprobe analyses, are used to quantify the silver losses in the copper clean¬ing flotation stages and to determine how overall silver and three silver-bearing minerals are recovered in the plant final products.RESUME Dix-neuf produits des circuits de flottation du cuivre et du zinc de la division Matagami de Noranda Inc. ont été échantillonnés pour leur distribution granulométrique, analyses chimiques et le contenu d'argent et d'or des fractions granulométriques. Le bilan métallurgique a été obtenu à l'aide du programme BILMAT. Ces résultats couples avec une etude minéralogique à la microsonde sont utilises pour quantifier les pertes argentifères aux diverses étapes de nettoyage du circuit de cuivre et pour de¬terminer la repartition de l'argent et des trois minéraux argentifères dans les produitsfinals de l'usine.INTRODUCTION The Matagami division of NORANDA INC. produces copper and zinc concentrates from a sulphide ore which contains a small amount of gold (0.34 g/t) and silver (20 g/t). Only a small part of the silver (~-30%) is presently recovered in the copper concentrate. The objective of this study is to evaluate the metallurgical behaviour of silver, and secondarily of gold, in the flotation circuit for a possible increase of its recovery in the copper concentrate to improve its economic value. For that purpose it is worthwhile to study the minerals which bear silver and to determine the critical flotation stages where they are lost in the tails. The methodology proposed here is based on a coupling of a mineralogical study and a detailed mass balance calculation in the flotation circuit."

Jan 1, 1986

By C. R. Edwards

"Equity Silver Mines Limited owns and operates an open pit silver 111ine located 37 km southeast of Houston in the Omineca District of British Columbia, Figure l. The property is approximately 300 km west of Prince George and 417 km east of the Port of Prince Rupert. This is the largest silver mine in Canada and one of the five largest silver producers in the western world.Equity is a subsidiary of Placer Development Limited, which owns 70 of Equity's issued and outstanding Common Shares. Placer was responsible for financing and developing the property and now provides general management and administrative services.All mining is by open pit methods, using three 1600 P&H shovels, eight 45 t Caterpillar and three 77 t Wabco trucks, three 40R rotary drills, two D8 dozers, one 9888 front-end loader and other ancillary equipment. We are now phasing out the Southern Tail pit and bringing the Main Zone into productior; see Figure 2.Comminution in the concentrator is achieved via primary, secondary, and tertiary crushers followed by rod and ball mills. The flotation circuit, with Southern Tail ore, produces a concentrate containing between 3 000 and 6 500 g of silver per tonne, 201 copper, and 25 g of gold per tonne. Running Main Zone ore, concentrate grades will decrease to about 4 500 g of silver per tonne, 17% copper, and 18 g of gold per tonne. Design milling capacity is 5 300 tpd, which is often exceeded.The flotation concentrate contains relatively high levels of antimony and arsenic. Because of these impurities Equity was unable to obtain economically acceptable long-term sales contracts for flotation concentrate. For this reason a leaching process was developed, and a plant designed, built and placed in operation. Due to the complex and unique technology involved, many start-up problems were encountered but by March 1983 the leach plant was considered ""fully operational."" This paper describes some of our progress and problems in bringing the Equity leach plant through its start-up period."

Jan 1, 1984

"An atmospheric process for the synthesis of scorodite(DMSP®)has beendeveloped,in which ferrous ions were oxidized by oxygen gas in the presence of pentavalent arsenic ions. Under optimum conditions, the synthesized scorodite (FeAsO4?2H2O) was well crystallizedand the crystals were faceted; the particle sizes were as large as 15 to 20 µm. In thisstudy, iron (II) sulfate heptahydrate (FeSO4·7H2O), arsenic (V) acid (60mass%H3AsO4) solution, and distilled water were used to prepare the original experimental solution (700 ml), in which the contents of Fe(II) and As(V) were 55.9 g/L and 50.0 g/L, respectively. The effects of various synthesis conditions, such as the type of oxidizing gas (oxygen or air), gas injectionrate, temperature, and the initial pH of the solution, on the size and shape of the scorodite particles wereinvestigated. From the experimental results, the changes in the shape of the scorodite particles wereclarified for each synthesis condition.INTRODUCTIONDOWA has developed a processfor synthesizing well-crystallized scorodite (FeAsO4•2H2O). Theprocess is named andtrademarked as DMSP® (Fujita et al., 2008; Fujita et al., 2008; Fujita et al., 2009; Fujita et al., 2009; Fujita et al., 2009, Kubo et al., 2010). In this process, oxygen gas is injectedinto a sulfuric acid solution containing large amountsof As(V) and Fe(II). Facetedscorodite crystals as large as 15–20 µm weregeneratedthrough the pre-formation of a gel-like precursor. However, it is known that the synthesized scorodite particles become smaller and more aggregatedwhen the synthesis conditionsdeviate from the optimumconditions.In this study, the effects of various synthesis conditions, such as the type of oxidizing gas (oxygen or air), gas flowrate, temperature, and initial pH of the solution, on the size and shape of the scorodite particles were investigated. The experimental resultsclarified the changes in the shape of the scorodite particles for each synthesis condition."

Jan 1, 2016

By Brian Penney

"The Iron Ore Company of Canada (IOCC} has mined and processed an iron deposit in Western Labrador along the Labrador-Quebec border since the early 1960' s. Current capacity is approximately 19 million tonnes of concentrate, 70% of which is converted to pellets at these facilities.The ore deposits are located in hills rising 150 to 300 meters above the adjacent lakes, and most of them are covered by very little overburden. The iron minerals are mainly specular hematite and magnetite hosted in a quartz formation. Crude ore averages 40% Fe that is concentrated to 65.5% Fe. IOCC is an extensive operation extending from Labrador City NF to Sept-Iles Quebec. It consists of open pit mining, concentrating, pelletizing, railway, and dock loading facilities.The Concentrator liberates iron from the silica by crushing and grinding the ore to -14 mesh (-1190 microns}. Ground ore is concentrated in spirals and filtered for transportation. Spiral tailings are treated in a Magnetic Recovery Plant (Mag Plant} that recovers lost magnetite. Mag Plant tailings are treated in a Hematite Spiral Plant (Hem Plant} that scavenges fine iron remaining in this stream.This report deals with ongoing iron recovery initiatives within the ConcentratorIron Losses in the ConcentratorIron recovery at IOCC is approximately 70.5%. This compares with recoveries that range from 65% to 86% for other iron mines in our area. Other world large iron ore producers dig and ship concentrate quality ore directly out of the ground and have an effective recovery of 100%. With increasing costs for labour, equipment, and supplies an increase in iron recovery is required to keep the operation viable.More than 90% of our iron concentrate is produced by gravity separation using spirals. The physical characteristics of the iron minerals that most effect recovery are mineral grain size and degree of liberation. We divide ground ore into three size categories -coarse, intermediate, and fines. A brief description of each size fraction follows:"

Jan 1, 1996

By Mei-Yan Yang, Qiu-Ying Wang, Ltd. Yunnan Yuntong Zinc Co., Guo-Mu Chen, Meng-Yang Huang, Peng Zeng, Guo-Feng Li

"Historically, alot of jarosite was found in the leaching residue when leaching indium from secondary zinc oxide materials. The reasons for the formation of indium bearing jarosite were theoretically analyzed. The influence of controlling the acidity and the addition of reagents on the indium leaching yield during secondary zinc oxide processing was investigated. In order to increase the leaching yield of indium, a measure of controlling the creation and destruction of jarosite was proposed. The production data shows that the leaching yield of indium was increased from 60 to 96%, and the content of indium in leaching residue simultaneously decreased from 900g/t to 100–200g/t when implementing such controlling measures.INTRODUCTIONIndium does not occur as independent minerals in the earth’s crust and is mainly associated with complex sulphide minerals. Specifically some sphalerites can contain as much as 900g/t of indium. Most indium is recovered from by-products of copper, lead or zinc metallurgy. Therefore, the research on the recovery of by-products in non-ferrous metallurgy is important(Sinclair et al, 2006). The main technologies used for this objective in China include: •,pre-neutralization-reduction-precipitation indium process(Yu et al, 2008), •,countercurrent oxidizing acid leaching process and sulphation roasting-water leaching process(Cao, 2005), •,oxygen pressure acid leaching of zinc concentrate-P204 extraction process(Yang et al, 2006), •,doubleacid leaching-solvent extraction process on lead dross from a reverbatory furnace flue dust(Liu, 2003),•,an acid leaching-solvent extraction process on smelting ash(Zhouet al, 2005). Although high pressure and extreme conditions can be used to improve extraction from high iron bearing indium residues(autoclave processing), mild extraction with lower cost and lower environmental impact are preferred.This paper describes both how the indium extraction using mild conditions in a secondary zinc circuit was quite low and, how through XRD and chemical analysis jarosite formation was found as the main cause. The paper then proceeds to discuss a method for improving the leaching yield and the application of this method in industrial practice."

Jan 1, 2016

By T. Gonzales, M. Maleki, M. Caçador, B. Climenhaga, H. Ghorbani

The campaign life of furnaces in the copper making industry is greatly affected by damage caused by normal operation cycling and abnormal conditions. Proper monitoring and assessment of the existing conditions and safe remaining life of the vessels and their refractory lining is key to prevent an unplanned early replacement. This paper presents an industry-proven refractory management program as well as a typical fitness-for-service assessment of a rotary vessel shell in order to extend the campaign life of copper making furnaces and enhance safety. The furnace refractory management system involves a comprehensive audit and monitoring program which has been successfully applied to several copper flash smelting furnaces over the past 15 years. The fitness for service assessment provides a methodology to estimate the remaining life of the steel components by evaluating the existing damage and future damage rate based on the historical survey data. The above practices can provide the operator with cost savings by extending the vessel campaign life in lieu of implementing more rigorous refractory lining and shell audits. INTRODUCTION Primary copper smelting is generally divided into two categories of flash smelting and open bath smelting. There are many different types of vessels that can be used to convert the copper concentrate to blister copper including, flash, Mitsubishi process, TSL (ISA/Ausmelt), SKS Bottom Blowing, Anode and Teniente/Noranda furnaces, reactors, and Peirce Smith converters. Each vessel has its own complex and intense environment which requires careful refractory and steel design to withstand the severe thermomechanical and thermochemical attacks within its campaign life. The campaign life of furnaces is greatly affected by damage caused by normal operation cycling and abnormal conditions. Proper assessment of the existing conditions and safe remaining life of the vessels and/or refractory lining is key to prevent an unplanned early replacement. This paper presents an industry-proven refractory management program as well as a fitness-for- service assessment methodology to estimate the remaining campaign life of copper making furnaces resulting in cost savings and enhanced safety of the operating vessels.

Jan 1, 2019

By Rene A. Morin, John K. Kebe

"As explosives become more widely used in urban and other congested areas, governmental regulations pertaining to their use are becoming more pervasive and stringent. This is forcing the blasting industry to review its entire spectrum of operations. Greater attention is now being paid not only to the design and layout of blasts, but also to the monitoring and recording of their after-effects for both legal and business reasons.Current PracticesThe major users of explosives in urban areas are quarry operators and construction companies. A characteristic of both of these industries, at least in recent years, is a relatively low margin of profit. This, coupled with the fact that their use of explosives is relatively intermittent, prevents them from having the kind of professional consulting services that blasting operations really warrant in today's regulatory environment. When such services are obtained, they tend to be directed more at the design and execution of the blast than at the recordkeeping function. The records that are kept tend to be more in the form of a summary of the consultant's design data as opposed to the kind of after-effect detail that is necessary.The more experienced consultants and operators now realize that at least as much attention must be paid to the record-keeping as to the design work. Regulatory bodies at all levels of government are insisting on the availability of such records.Unfortunately, the instrumentation in use today for taking such measurements does not lend itself to the practice of intermittent consulting. Current monitoring and recording instruments are based on so-called analog technology of the type that has traditionally been applied to the monitoring of earthquakes. They require set-up and calibration procedures which must be repeated each time the instrument is moved, or the blasting parameters are changed, as well as complex total analysis of the recorded data. This can lend to confusion and a dilution of responsibility for anything other than the design work and possibly some summary reporting."

Jan 1, 1985

By J. -P. Tshibangu, M. Ramos da Silva, F. Descamps, C. Schroeder, J. -C. Verbrugge

"The mechanical behaviour of rock materials is largely influenced by the stress state and pore pressure; this needs to be considered in many applications, such as petroleum engineering, tunnelling or stability of underground excavations.Conventional triaxial tests (d2 = d 3) are generally used to assess the influence of confining and pore pressure. In this work, those tests are performed on a porous rock named Sorcy limestone, along with more advanced stress paths like triaxial extension (d 2 = d 1) and purely deviatoric tests with independent pore pressure control. Those tests are combined to a true triaxial study on the dry rock in order to investigate the effect of true triaxial stresses and, hence, build three-dimensional limiting envelopes accounting for the influence of pore pressure.Three-dimensional limiting envelopes of dry Sorcy limestone are built in meridian and octahedral planes. The shape of the octahedral sections changes with the mean stress from triangular to hexagonal and then quasi circular. At even higher mean stresses, the evolution continues towards a triangle with apexes oriented in the direction of triaxial extension stress states. In meridian sections, the deviatoric stress first increases with the mean stress. The transition between this deviatoric mechanism and the cap surface occurs at different mean pressures depending on the Lode angle.Terzaghi’s effective stress is found to govern the yield and plastic behaviour of saturated Sorcy limestone. Triaxial tests show that the limiting envelope does not depend on the loading path (conventional compression and purely deviatoric stress paths). In triaxial extension, the brittle-ductile transition is observed for a higher mean pressure than in triaxial compression, as previously found for true triaxial tests on the dry rock.Finally, it is shown that upon appropriate normalisation, the dry and saturated yield envelopes come very close one to each other. This suggests that only the size of the yield envelope changes between dry and saturated state (pore pressure = 5 MPa); its shape does not seem to evolve."

Jan 1, 2015

By Jorge Lema Patino

"The purpose of this paper is to determine the best techno-economic alternative for the treatment of tin ores, when comparing the various mining and metallurgical methods of preconcentration, concentration, volatilization (fuming) and up to the final stage of selling to the smelter. The study of the influence of the different parameters of cost, recovery and quoted prices has motivated the paper, which aims at determining the best process of ore treatment in terms of its techno-economic feasibility.Method of WorkOn the basis of head grades of 0.5, 0.75 and 1.0% tin, the following alternative methods of treatment are possible:1. Mining-Concentration-Smelting.2. Mining-Preconcentration-Fuming-Smelting.3. Mining-Concentration-Separation, with direct smelting and fuming/smelting of the two fractions produced.The calculations were carried out on the basis of existing information and publications concerning the various experimental recoveries in the operating mills of COMIBOL. In the case of concentrates containing less than 10% or more than 40% tin, extrapolation was required.The final grade of the tin concentrates and the gross weight of the concentrate were calculated on the basis of the estimated recovery curves. The costs of the preconcentration and the concentration stage s were determined per gross metric ton of material treated.The calculation of the cost of the smelting stage is similar for all the alternatives, the royalties and smelting charge varying with the grade of the final concentrate. In the fuming stage, a uniform recovery of 90% was taken in all cases so as to obtain a final concentrate grade of 65% tin, regardless of the head grade of the feed material.For the separation stage, the following considerations apply:a) Separation can be carried out by gravity separation or flotation methods.b) The cost of separation varies depending on the system used.c) The distribution of tin in the two fractions is 100% at this stage. In other words, there is no loss of tin during separation."

Jan 1, 1982

By H. W. Smith, D. Guerin

"This paper describes the development of a dynamic model for a full- scale (64 tonnes/hr) grinding circuit consisting of an open-circuit rod mill feeding a ball mill operating in closed circuit. The object of constructing such a model is to investigate the static and dynamic behaviour of potential control schemes. Model selection, data processing and parameter estimation are discussed, and static and dynamic results of simulations are presented. Conclusions are drawn with regard to the adequacy of the model for such studies, and likely limitations on control of such circuits.IntroductionThe model developed here is intended to represent the grinding behaviour of the grinding circuit at the Lake Dufault division of Falconbridge Copper Mines Ltd. This circuit has been fully described elsewhere. At the time of the work described, the ball mill discharge was fed to a four-cell flotation bank , the tailings of which are combined with the rod mill discharge in the cyclone feed pump sump. As the emphasis in this study is on grinding behaviour, and as only I per cent of cyclone feed material is removed in these cells, no attempt has been made to include flotation behaviour in the simulation. One effect of the presence of flotation cells in the grinding circuit is, however, to necessitate somewhat finer grinding than might otherwise be needed: this will have effects on mill parameters.The paper is organized as follows. First the selection of models is discussed, paying particular attention to the problem of selecting simple, yet adequate, flow models for the mills. Then data gathering is described. The method of deriving mill model parameters is explained, and the results presented. Mass balancing of cyclone data and the determination of cyclone model parameters are described. The linking of the models into a full simulation is outlined, and sta tic and dynamic results presented. Finally, the results are discussed and conclusions drawn ."

Jan 1, 1980

By J. L. Collins

"This paper deals with the quantitative analysis of mine maintenance records. Based on a case study of dozer engine records, the author suggests an easy method of deriving useful information for managerial decisions in a step-by-step manner.More specifically, the paper deals with the following topics:• determination of the most economical replacement time,• determination of reliability characteristics,• determination of the number of replacements, and• determination of the number of spares.IntroductionThe mining industry collects a lot of information about every aspect of its activities, an example of which appears in Table I. In Table I , the distribution describes the operating hours at failure of 56 different dozer engines used in severe applications. Besides calculating an average and possibly a standard derivation from the data, little else is derived, at least from a statistical point-of-view.More information can be obtained from these records that could help management in the decision-making process.To illustrate this point, the sample data appearing in Table I will be analyzed in detail by making use of well-known concepts in reliability engineering.Distribution of DataTable I represents a distribution obtained from the recorded hours cumulated from the operators' time cards. The operating hours have been divided into fourteen classes for each 1000 hours of engine running, e.g . all engines scoring an operating time of between 1001 and 2000 hours formed a class , those scoring between 2001 and 3000 hours another one, etc. Generally, the class interval should be a multiple of the equipment preventive maintenance check period.The minimum acceptable sample size should be large enough to ensure that the score in each class interval is at least one. Ideally, the score for each class interval should be at least five so that a chi-square test could be carried out if necessary.The average life of an engine can be found by adding the products of the frequency and the class mark (mid-point) values. Therefore:"

Jan 1, 1987

By Michel Garon

"Several years ago computer control of the flotation process was successfully implemented at the Matagami concentrator of Noranda Mines Inc. At that time this was the first computer application being installed at this operation. The last few years have seen an extensive use of programmable controllers in areas such as the copper and zinc dewatering circuits and the lime preparation system. With the aid of such instruments, these areas have attained a high level of automation and as a result, a high degree of efficiency. The controllers have proven to be very dependable and easy to use.IntroductionThe Matagarni Division of Noranda Mines Inc. operates two mines in the Matagami District of northwestern Quebec which is located about 650 km northwest of Montreal. The mines ship ores to a central concentrator whose throughput averages 95,000 tonnes of ore per month. Metal contents of the mill feed average 0.9 per cent copper and 5.0 per cent zinc. Concentrate outputs are approximately 3,200 tonnes of copper and 8,200 tonnes of zinc per month.The concentrator commenced operation in 1963. An on-stream X-ray analyzer was installed in 1968, providing analyses of several samples in the flotation circuit without the aid of a computer. In 1974, control of the circuit by computer was added to the system. As a result, zinc flotation efficiency improved considerably and reagent costs decreased through the reduction of copper sulphate consumption.In the past few years it was realized that significant improvements could also be made in other parts of the operation . Copper and zinc dewatering circuits and the lime preparation system were identified as major areas that could drastically benefit from automation. In 1982, programmable controllers were seriously considered as an attractive alternative for achieving the company 's goal. Because of their relative lowcost and their high degree of flexibility, they were selected for implementing automation and, for improving the efficiency in each of these areas."

Jan 1, 1985

By Ludwig Strah

"The paper outlines the history of rubber mill liners beginning with the awarding of the first North American patent rights in 1923. It includes the early-day applications and installations of the 1920s and 1930s through to their present-day application. Over-all rubber mill liner design is discussed in relation to present day installations employing rubber mill liners in various grinding applications. A brief overview is given of a manufacturer's procedures to produce rubber mill liners.IntroductionIn early 1910, it became apparent that the productive life of the silver mines in Cobalt, Ontario, could be substantially prolonged by mining lower-grade ores.The mining of lower-grade ores required the establishment of treatment facilities which initially employed jaw crushers, stamp mills, jigs and concentrating tables. The recovery of silver in other than a coarse metallic form required the additional step which was introduced at that time: the cyanidation of silver concentrates from the tables. The resultant requirement for increased and improved recovery led to the introduction of grinding mills, i.e. tube mills.Shortly after the introduction of the tube mills to the Nipissing Mine's mill in 1914, the idea of using rubber as a mill liner material was spawned. However, no action was taken due to the advent of World War I. It is interesting to note that the idea of rubber mill liners emanated from having used pieces of solid rubber tire as an emergency repair on a set of liners when a liner had broken and no immediately available spare was on site.The credit for this ingenuity and subsequent application for a patent on rubber mill liners falls to James John Denny, the mill superintendent, and Rolla Barnum Watson, the general manager of Coniagas Mines Limited. The patent application was formally made on December 3, 1921. The U.S. Patent Office issued Patent No. 1,470,597 on October 16, 1923."

Jan 1, 1982

By Robert B. Parsons

"Thrashing one's way through a jungle of entangled tax rules is no easy task today, as Canada's legislators continue to complicate this country's income tax laws. At some magical point, there is presumably some balance to be struck between legislation which is equitable and unambiguous on the one hand, and at the same time is efficiently complied with and administered. It is becoming increasingly clear that the legislation is not in balance, and that there is a pressing need for some simplification of the income tax rules and regulations especially in areas of critical importance to the resource industries-even though such simplification will likely involve some sacrifice of equity and certainty.Introduction""I would wish that ... the superfluous and tedious statutes were brought into one sum together, and made more plain and short, to the intent that men might better understand them."" Edward VI, King of England 1547-1553.Regal decree notwithstanding, the legislation of most developed nations continues to become more complex, lengthy, and confusing than ever before. Canada's income tax system cannot escape the accusatory finger pointing at examples of this serious problem which plagues all of us today.Although many areas of our tax law could easily warrant some degree of simplification, for those who are involved with this country's resource sector, that horrendous, almost unreadable, part of our tax legislation which deals with resource taxation must be regarded s a prime candidate for simplification. In recent decades, but particularly in the past ten years since tax reform in 1972, budget after budget, both federal and provincial, have amended, massaged, modified, and manipulated the resource tax rules to the point where not only are taxpayers totally lost in their attempts to make some sense of the entanglement of rules, but also the draftsmen themselves acknowledge that the outer limits of complexity are being reached, and that the whole set of rules is on the verge of grinding to a groaning halt under its own weight of nonsense and frustration."

Jan 1, 1982