Search Documents

By M. Huang

Electrodeless conductivity was employed to investigate the feasibility of continuous on-line monitoring of the free acidity of sulphate and/or chloride solutions of Cu and other base metals from various hydrometallurgical processes. These solutions were measured with both commercial and experimental electrodeless conductivity sensors from 15 to 250°C. It was confirmed that hydrogen ion has the greatest impact on conductivity by carrying the bulk of the current because it is the most mobile ion. In combination with a solution speciation analysis the conductivity sensor can be calibrated to account for the contribution of Cu electrolytes as well other dissolved salts allowing fast and accurate on-line measurement of free acid. The sensor was tested at both lab and pilot scale with very good performance. The average difference between the measured and the titrated acid concentration was less than 5%, which is excellent for industrial applications.

Jan 1, 2007

By O. -J. Siljan

"Refractory materials are an integral part of aluminium production. One special feature of aluminium making is the prominent role of sodium in all parts of the production process. This presence of sodium inflicts stresses on the refractory materials through reactions and may cause severe damages to the refractory linings. The present paper address possible reactions between sodium and refractories in anode bake furnaces, electrolytic pots and casting furnaces. The discussions presented in the paper points to the importance of selecting materials with excellent alkali resistance in all parts of the aluminium making process, although alkali resistance is not the sole parameter to determine refractory life-time. ""Acid"", i.e. silica-rich alumino-silicate refractories are shown to be the best materials for aluminium electrolysis cell potlinings, whereas high- alumina refractories based on minerals like andalusite seems to be the preferred choice for anode bake furnaces as well as cast house furnaces."

Jan 1, 2004

By T. Belem

In-stope backfill will cure under effective stress, which develops due to a combination of mechanical consolidation (free draining material) and ??chemical consolidation?? (self-desiccation mechanism). A good knowledge of all the drainage and consolidation characteristics of cemented paste backfill is crucial for a better design of underground backfilling sequencing. From many of the existing results and studies done by various authors, as well as the availability of some in-stope backfill pressure data measurements during and after filling, it is possible of developing a procedure of backfilling sequencing. Hence, the objective of this study is to provide a guide for underground backfilling sequencing in the view of preventing the development of excess pore pressure that will affect both the stability of the barricades and the strength development of the backfill. This will be possible by considering the interaction between consolidation/drainage rate, filling rate and binder hydration rate.

Aug 1, 2013

By A. Bauer

The correct application of large crater blasts in unfrozen tar sand is an effective means of resisting frost penetration during winter. This results in much higher productivity and considerably less down time with excavators during winter operations. The resulting flatter angle of repose of the highwall has readily been accommodated with slight modification to bucket-wheel excavator operating procedure. Other mining schemes call for large draglines to be located on top of the highwall, which can be as high as J80 feet. The question now arises as to the effect that blasting might have on the stability of such a situation in which the highwall includes potential planes of weakness. This paper applies blast vibration data from large-scale blasting in tar sand to the stability analysis for typical production situations likely to be encountered and indicates safe scaled distances to be employed between dragline and blast.

Jan 1, 1979

By J. E. Zajic, E. A. Sullivan, T. R. Jack

"The release of vanadium, iron, nickel and titanium from the cokes produced in the upgrading of Alberta oil sands bitumen has been assessed for simple chemical leaching processes. Flexicoker coke (Exxon Engineering and Research) has been found to be quite amenable to the recovery of vanadium as well as nickel, iron and some titanium by these techniques, whereas fluid coker coke (Syncrude) and delayed coker coke (Great Canadian Oil Sands) are relatively intractable under the mild conditions employed. The factors affecting the extent of vanadium release are discussed in terms of the surface area accessible, the wettability of the material, and the chemical and physical composition of the coke particles in each case.A novel biologically assisted heap leaching procedure for f1exicoker coke is also described, based on the growth of the chemolithotrophic bacteria, Thiobacillus thiooxidans A TCC 8085, on elemental sulphur added to the coke."

Jan 1, 1980

By J. M. Ortiz, J. Haas, W. Kracht, G. Pamparana

This work explores the effect of ore hardness variability on the design of a solar photovoltaic system with battery storage and grid backup, to operate a semi-autogenous grinding mill (SAG). First, a case of two synthetic ore populations was studied, without any consideration of spatial distribution. The mean and variance of the ore hardness (measured in specific energy consumption) of both populations were subjected to a sensitivity analysis. The operation was evaluated with one and two stockpiles. The latter allows classifying according to ore hardness to adapt the SAG energy consumption to the solar cycle. The results show that using two stockpiles allows achieving a larger autonomy (i.e., fewer energy imports) at lower total costs, especially when the difference of mean hardness between the two populations is large. The difference in variance (between the two populations) has a smaller impact on the design recommendations. Second, a case study was performed considering the spatial distribution of geometallurgical units. Two cases were considered: (a) brownfield, when there is historical information of the actual variability of the ore hardness; and (b) greenfield, when the system design relies mainly on geometallurgical modeling. Brownfield and greenfield planning result in similar sizing recommendations of the solar power plant if precise drill cores are available. In this case, geometallurgical modeling is an effective tool for forecasting the energy demand necessary for designing the power plant. INTRODUCTION Solar energy can help make mining more sustainable (Moreno-Leiva et al., 2017). With falling battery costs, an autonomous solar supply is soon to become an economical alternative in many parts of the world, even in the presence of a larger power grid (Child et al., 2017). Although this, places with high solar radiation such as the Atacama Desert in Chile, nowadays show a large potential of incorporating solar energy as a supply of energy. Many of the Chilean copper mines are in this zone making it interesting to study their compatibility and potential of integrating this renewable source to their operation. The power demand in a copper mineral processing plant is determined by the main power loads in grinding and flotation, with grinding typically the largest power consumer, especially the semi-autogenous grinding (SAG) mills (Wei and Craig, 2009). In Chile, it corresponds on average the 50% of the electrical energy consumption (COCHILCO, 2013). Solar energy production is determined by the irradiance perceived into the solar photovoltaic (PV) panels (which varies through the geographic location) and several other climatic parameters such as the current season, humidity, temperature, altitude, and others (Molina et al., 2017). Also, solar energy is only generated during the sun hours, getting to a maximum generation at a certain peak hour during midday, and finally dropping to zero during the night. This shows a cyclic parabolic profile as shown in Figure 1. Due to the SAG mill operated continuously, the power supply always must be available. During the night, to continue supplying the energy, it is necessary to complement the solar power generation with a battery energy storage system (BESS), which will act as a power backup and a buffer. For the optimal sizing of this PV- BESS system, information of the demand profile is needed (Pamparana et al., 2017). In the case of the SAG mill operation, the resulting demand relates to the ore-hardness for a specific throughput and grind size (Morrell, 2004). Therefore, for a given throughput and target grind size, a harder ore would require more power, and variable hardness results in more variable demand and a subsequent need for larger energy storage (Bueno et al., 2015). Due to the ore-hardness variability and the operation of the mill, the power demand profile in inherently variable.

Jan 1, 2019

By M. M. Papic, G. M. Kimber

"Hat Creek coal was treated by the liquid solvent extraction process in a continuous plant at the U.K. National Coal Board Coal Research Establishment.Extraction levels of over 80 per cent dry-mineral-matter-free (dmmf) coal were achieved.Total light oil yield was around 47 per cent of the dmmf coal. The light oil was shown to be a good feedstock for secondary refining into gasoline, jet fuel and diesel fuel.In spite of the high mineral matter content of the coal the solid residue was successfully removed from the coal extract by filtration.IntroductionBritish Columbia Hydro (BCH) and the National Coal Board of Great Britain (NCB) undertook a joint project to test the Hat Creek coal from British Columbia in the NCB's coal liquefaction process designed to produce transport fuels and feedstocks for the chemical industry by the liquid solvent extraction of coal(1), In this process most of the coal is dissolved in an aromatic solvent and the residual solids consisting of mineral matter and undissolved coal are removed by filtration. The resultant coal extract solution is fed to a hydrocracker for conversion to light liquid products and a fraction suitable for recycling as solvent. The light liquid products can be converted to gasoline and diesel fuel in a secondary refining stage.The dissolution of the coal is effected by heat-treating a slurry at a temperature in the region of 400°C which causes some bonds in the coal to rupture with the formation of radicals(2,3). These radicals are stabilized by hydrogen transfer from the hydroaromatic groups in the solvent, resulting in a reduction in the molecular weight of the coal. In the absence of donor groups the radicals combine to form an insoluble high molecular weight product(4). From studies of the kinetics of these reactions it has been shown that the formation and stabilization of the radicals is rapid at temperatures around 400°C(2,3). The dissolution of the depolymerizing coal is, however, relatively slow and the need to ensure complete dissolution in order to achieve a high extraction restricts the selection of digestion time(5). Further, it is important that digests do not contain depolymerizing coal as it may re-form under the applied stress in the filter cake inhibiting flow through the bed and resulting in low filtration rates(6).Thus, in practice relatively long digestion times are generally required in order to ensure complete dissolution of the depolymerizing coal, while it is also important to avoid depletion of the hydrogen donor groups in the solvent which would lower the rate of hydrogen donation to the coal and thus reduce the extraction yield and adversely affect the filtration(7). Clearly it is desirable to optimize the digestion time and temperature with regard to the extraction yield and filtration properties.The precise control of the distribution of products from the hydro-cracker is important for the composition of the recycle process solvent. The principal functions of the solvent are to provide a source of donatable hydrogen and a vehicle for the dissolution of the depolymerizing coal. Hydrogen transfer from the solvent, achieved by the conversion of hydroaromatic to aromatic groups, stabilizes the radicals formed by thermal cleavage of some of the bonds in the coal resulting in a progressive reduction in the size of the coal molecules(8,9) and dissolution in the solvent. The combination of radicals would result in the formation of insoluble material and a reduced extraction yield of the coal(4). Thus to achieve a high extraction yield the solvent should contain sufficient hydrogen donor groups to prevent extensive radical combination. The composition of the solvent should also be controlled to allow dissolution of the depolymerizing coal and to prevent precipitation of this material during the subsequent processing of the coal digest and extract solution. The formation of a precipitate not only reduces the extraction yield of the coal and adve"

Jan 1, 1985

By B. W. Raymond, D. W. Zandee

"IntroductionCoal deposits are found in many regions in Canada and vary widely in their age, quality and rank. All classifications of coal except anthracite are found in significant quantities in this country.Deposits in the Maritimes are mainly bituminous; Lignite is found in Saskatchewan and Ontario and sub-bituminous coal in the plains region of Alberta. The Rocky Mountain coalfields of Alberta and British Columbia contain low and high-volatile bituminous coal and, in a few places, semi-anthracite. The British Columbia interior contains deposits of semi-anthracite, bituminous, sub-bituminous coals and lignite. The Yukon and Northwest Territories also contain substantial deposits of bituminous coal and lignite.Currently Nova Scotia produces both thermal and metallurgical coal, Saskatchewan produces lignite and Alberta produces both sub-bituminous and bituminous coal for thermal purposes. Large deposits of metallurgical coal are now being exploited in the Rockies arefl of British Columbia and Alberta by open pit methods. The raw coal is treated in large capacity preparation plants to remove refuse and upgrade the product to a consistent metallurgical quality with respect to ash, moisture, volatile matter and coking properties.The treatment of coal involves crushing, screening and cleaning by dense medium, jigs, water-only cyclones, tables and froth flotation to produce a diverse range of coal products differing in quality and size for various end uses.The chapter on Crushing and Screening Circuits was concerned mainly with crushing of metalliferous ores to produce a concentrate of one or more valuable minerals which normally constitute a small portion of the original mass of the material treated.Coal differs physically from ores in many ways such as lower specific gravity, relatively large volumes but low tonnage of product, and its habit of absorbing moisture requires extensive dewatering processes more complicated than settlement and filtration. Most significant, for this paper at least, is the fact that crushing coal is not as energy intensive and much smaller equipment is applicable.Crushing and screening of ores is intended to reduce the size of all constituents as quickly and efficiently as possible to allow liberation of the mineral particles. The crushing of coal is different in that the coal is not the minor constituent and the production of fines, in the initial stages at least, is highly undesirable. The basic objectives of crushing coal are the reduction of run-of-mine material to sizes suitable for cleaning or further reduction of coal to market sizes."

Jan 1, 1989

By Franc R. Joubin, Donald H. James

"The Algoma (or Blind River) uranium district is centred in an area of some 600 square miles on the north shore of Lake Huron, about half way between Sudbury and Sault Ste. Marie, Ontario (Figure 1). Its favourable location, adjoining the main provincial highway and Canadian Pacific Railway line which follow the lake shore, has contributed greatly to its rapid development.By Canadian standards, the district has long attracted geological attention, beginning with the discovery of the Bruce mine in 1846. It has been repeatedly prospected at intervals since then, chiefly for copper and nickel but also for lead, zinc, cobalt, silver, iron, and gold. Numerous discoveries have prompted the suggestion by Yates (13) and others that one metal-logenic province embraces the entire mineralized area from Michigan through Sudbury and Cobalt.Geological mapping was initiated by Murray in 1847, and the area attracted much interest as the type locality of the Huronian, the correlation and stratigraphic position of which are still not entirely agreed on. Subsequent contributors to the geological literature of the area have been very numerous, and the bibliography at the end of this paper includes only some of the more modern reports.The history of uranium in this part of Ontario also dates from 1847, when J. L. LeConte identified as uranium-bearing a pitchblende-like mineral which he named ""coracite"". The specimens came from Theano Point, north of Sault Ste. Marie. In 1948 a search for the source of these specimens led to the discovery of the Camray uranium field. Occurrences in this field consist of numerous small and locally rich pitchblende-bearing fractures, within or along the contacts of diabase dykes cutting Archaean granite and gneiss.None of the showings explored proved large enough to justify production, but they stimulated prospecting of adjoining areas and thus led to the Algoma discoveries.The first find of radioactive conglomerate in place was made in 1949 in Long township, and it was partially staked as the Fisher-Audette-Breton property. Rusty, overgrown rock-cuts indicated that the pyrite-bearing conglomerate had been investigated years before, probably during searches for base metals and gold. Examinations were made at this time by a number of geologists, including the senior author. In spite of high radioactivity, sampling returned only negligible uranium. The claims were allowed to lapse and the showings reverted to obscurity."

Jan 1, 1949

By R. D. Livingstone

"THE LETHBRIDGE COAL FIELD lies mainly .to the north and west of the city of Lethbridge. Mining carried on in this area for over eighty years until 1965. Before the building of a railway the coal was carried by bullock wagon to Montana for use in smelting, and for a while by river boat to Medicine Hat for railway use. The single, almost flat, worked seam is designated the ""Galt"" seam and is about 1.5 metres thick. It belongs to the Belly River formation and is under cover of 80 to 180 metres of weakly stratified sediments. A complex system of cross faults adds to the mining difficulties. Close timbering required in the entries and rooms reflected in a high timber cost and lower output per man shift. The coal is High Volatile"" C"" bituminous in rank with maximum gross calorific value of 11,200 Btu per pound and with a well defined cleavage. Roof conditions in the field range from very tender and very heavy on the south end of the field and west of the Oldman River to a more stable character to the north. Relatively speaking, the whole field would earn a rather tender rating and definitely so in relation to many U.S. fields. Floor conditions are characterized by a bentonitic type heaving in the south end of the field west of the Oldman river to a more stable situation in the north, which can tolerate shuttle car operation if kept drained. Water problems are minimal, except paralleling the Oldman River, where the seam dips below the river level. While vigilance is necessary to prevent accumulations of gas, the volume is rather limited. The seam was entered by shafts, except where small mines were located along the Oldman river banks and gained access by drifts. The coal seam was developed by driving either 3 or 4 Face entries 2 1/2 metres (8 ft) wide on 18-metre ( 60-ft) centres. Sets of dual butt entries driven at right angles to the Face entries completed development work. Normally rooms up to 8 metres wide were turned off the butt entries on up to 11 - metre centres. These were worked in groups of three to five, depending on the roof conditions, and normally advanced 60 m (200 ft). In some areas rooms had to be abandoned short of their objectives due to roof pressure, heaving floor and intermittent work."

Jan 1, 1985

By Laxman M. Amaratunga, Glen G. Hein

"Most mining operations utilize the tailings coarse fraction for backfilling while the fines have been traditionally disposed on surface in tailings ponds. Recently, paste fill has been developed which uses a fraction of the fine tailings (10-30% w/w of <45 µm) in the fill (Brummer and Moss, 1991). This development allows a mining company to use a portion of the fines for backfill, but still requires surface impoundment of the unused tailings. Reactive tailings have the added problem of generating acid after being oxidized in the presence of air and water. Treating acid mine drainage (AMO) from these ponds has proven to be a costly environmental problem and a long term liability.One practical method to reduce the environmental impacts associated with the tailings pond is to modify the physical and chemical prope1ties of the fine tailings so that they can be utilized in an environmentally safe manner. This was accomplished by agglomerating the tailings into pellets and using theses pellets as a coarse aggregate in a total tailings paste fill. This technology does not require any supplemental sand or gravel to be added to the fill.This paper presents the ongoing research into utilizing these tailings agglomerates as a coarse aggregate fraction, in order to create a total tailings paste fill which has supe1ior strength characteristics.IntroductionThe Canadian mining industry produces more than 500 million tonnes of tailings and waste rock annually. The waste rock is usually returned underground for use as rock fill in underground support with the tailings remaining to be disposed of in tailings ponds. Tailings consist of a coarse and fine fraction, and can be either reactive (acid generating) or non-reactive. In an effort to minimize tailings disposal, the coarse fraction has been used underground in backfill along with alluvial sands. This diversion of the coarse fraction, however still requires that the fine fraction be disposed of in tailings ponds. This disposal creates the potential for acid mine drainage (AMO), since in the presence of air and water, reactive sulphide tailings can generate acid. It is therefore an important goal in the mining industry to minimize the disposal of fine tailings into tailings ponds since the treatment of AMO is a costly and long-te1m environmental liability."

Jan 1, 1997

By J. X. Guo, A. Pindred, J. Moore

"Two modified centrifugal flotation cells (CFC), Q2 and Q3 models, have been developed for froth flotation. The operating mechanism of Q2 uses a rotating bowl to create a centrifugal force on the feeding slurry. Froth concentrate is collected on the central top of the cell and tailing is discharged along the top edge of the rotating bowl. The Q3 utilizes a vertical rotating feed pipe to introduce the feed slurry into a stationary flotation column cell. A centrifugal force is also created by a rotating pipe for the feeding slurry. Froth concentrate floats over the cell and tailing discharges through the bottom of the cell. The centrifugal force causes the flotation recovery of fine particles from CFC to be higher than from the conventional cell. The major operating variables of CFC are the rotating speed, air flow rate into feed slurry, and slurry feeding rate etc. Flotation tests have been carried out on synthetic mixtures of galena-silica and chalcopyrite-silica, as well as some natural base metal ore samples. Parallel tests were also conducted on a conventional flotation cell. The comparative test results demonstrated that both Q2 and Q3 have the advantage of higher recovery of finer than 10 µm mineral particles, which are very difficult for the conventional non-centrifugal flotation cell to recover. The grade-recovery curves produced from CFC are equivalent to or better than the conventional flotation cell. There is a potential in the future for the CFC to be employed in slime flotation.1. IntroductionA centrifugal flotation cell (CFC) was originally developed by Clean Earth Technologies [I] to separate oil from water and was subsequently applied in froth flotation. Figure 1 illustrates the design of the original CFC, in which a vertical feeding pipe is attached to the center part of a rotating drum and a stationary shell encloses it to direct the float froth and tailing discharge. The slurry flows down to the bottom of the spinning drum, gets in touch with a screen of air bubbles and then migrates outwards under the effect of centrifugal force. After the mineralized froth enters the rotating cell, it is pushed back to the inner surface. The overflowing froth is collected in the froth launder while the tailing slurry is discharged through orifices along the outer rim of the drum."

Jan 1, 1998

"At the May 15, 2006 and the May 1, 2007 Canadian Securities Administrators (CSA) Canadian Institute of Mining, Metallurgy and Petroleum (CIM) meetings in Vancouver and Montreal, CSA requested CIM consider certain issues arising out of the CSA review of Technical Reports and public disclosure, in general, regarding the practice of estimation and reporting of Mineral Resources and Mineral Reserves. The following is a summary of the issues raised by the CSA and the responses of the CIM.Preamble: At the May 15, 2006 and the May 1, 2007 Canadian Securities Administrators (CSA)-Canadian Institute of Mining, Metallurgy and Petroleum (CIM) meetings in Vancouver and Montreal, CSA requested CIM consider certain issues arising out of the CSA review of Technical Reports and public disclosure, in general, regarding the practice of estimation and reporting of Mineral Resources and Mineral Reserves. The following is a summary of the issues raised by the CSA and the responses of the CIM Reserve Definition and the CIM Estimation Best Practices Committees (the Committees). This information is intended to provide the Qualified Person (QP) with further guidance when estimating Mineral Resources and Mineral Reserves and in preparing a technical report written under National Instrument 43-101 (NI 43-101). Several members of the CIM Reserve Definition Committee, the CIM Estimation Best Practices Committee and some members of the Committee for Mineral Resources International Reporting Standards have reviewed these issues and provide the following commentary.Issue 1. - CSA requested CIM review and comment on the selection of an appropriate commodity price to be used in Mineral Resources and Mineral Reserves estimates.Commodity prices are used in the estimation of Mineral Resources and Mineral Reserves and in the economic analysis of a property. In times of rapidly changing commodity prices, or when prices are at the extreme ends of a commodity price cycle, the QP has a difficult job in selecting an appropriate commodity price.• The selection of appropriate technical variables, including commodity price, is clearly the responsibility of the Qualified Person (QP). The QP must describe the reasons for selecting these variables, including price, in the technical report.• The definition of a ""Mineral Resource"" contains the wording ""reasonable prospects for economic extraction,"" therefore, a QP must select economic parameters, including commodity price, that will result in an estimate of Mineral Resources and Mineral Reserves that have ""reasonable prospects for economic extraction""."

Jan 1, 2003

By S. Eckert, M. Reuter, O. Keplinger, D. Obiso, N. Shevchenko, M. Akashi

We report on laboratory experiments focusing on bubbling phenomena arising from gas injection through a top submerged lance (TSL) in a liquid metal layer. The objective of this study is to reveal the characteristics of the formation and behaviour of the particular bubbles at different gas flow rates and submergence depths of lance. Visualization was performed in the eutectic alloy GaInSn using X-ray radiography. Argon bubbles were injected through the injection positions at three different submergence depths. Essential parameters such as the bubble size, bubble shape, detachment frequency and the two- dimensional gas distribution in the flat vessel were obtained by image processing. The results show that the deep position of the submerged lance causes an asymmetric large-scale circulation inside the fluid vessel. Bubble detachment frequencies were calculated by Fast Fourier Transformation from fluctuations of the image intensity in the vicinity of the nozzle injection point. This frequency does not show strong variations with respect to changes of the gas flow rate and the submergence depth of the nozzle. An increasing gas flow rate results in an increasing two-dimensional projected bubble area and the occurrence of a significant number of small bubbles being trapped by the strong fluid flow in the liquid metal layer. INTRODUCTION The Top Submerged Lance (TSL) process has been an essential component of the metallurgical industry since the emergence of first concepts about 50 years ago (Floyd, 2005). The process, which is characterized by blowing reactive gas through the submerged lance into a liquid bath, was developed mainly for improving the tin smelting process and has been applied for waste treatment or the production of several metals such as copper, lead, nickel and zinc. The productivity of the reactor is determined mainly by the efficiency of the chemical reaction between the gas or solid particles and the liquid. To achieve a high efficiency requires good exchange between the gas-liquid phase and therefore a large interface area. The efficiency changes greatly with the number and size of bubbles injected from the nozzle and the extent of splashing on the free surface. The degree of turbulence in the bath plays a decisive role here. For the reason, the design of an efficient TSL process requires a profound knowledge of the fluid dynamics especially for complex multiphase flows.

Jan 1, 2019

By G. R. Heffernan

"In the early 1970ssteelmakers worldwide were looking forward to many years of expansion and profitability. Huge government investments in Europe, the United Kingdom, Japan, Brazil, and Venezuela were committed in anticipation of growing market s based on long-term OECD forecasts. In 1973 the first OPEC oil shock occurred. Steel demand shrank. Restructuring became the buzz word of the day as billions of dollars in taxpayers&apos; money was poured into eliminating excess capacity and labour. In the United States, where government help was not available, inefficient companies went bankrupt; capacity was cut to 100 million tons from 155 million tons. The industry throughout the industrialized world shrank. By 1979the world economy seemed back on track and a modest degree of optimism could be detected in the international steel fraternity. Then came the second oil shock. By 1982 the industry was in the midst of another shakeout. More bankruptcies, more rationalization, and fewer jobs resulted. In Canada some well-known companies came close to the brink as low prices and high interest rates took their toll. In the light of the turmoil in the steel market over the past 20 years an attempt to forecast the trends through to 2001 is intimidating.However, there are good reasons to be optimistic today about both markets and technology.An economic super power is emerging in western Europe as 1992 draws near. The creation of a single market of 320 million well educated and economically ambitious people has major positive implications for steel demand. The mega projects of the channel tunnel, a European network of high speed railways, and the London docklands are the forerunners of greater things. Still to come is another $200 to $300 billion by the year 2001 in identifiable major projects for highways, railways, airports, water and sewage systems. Add to that the demands of an increasingly affluent population for automobiles, appliances and housing. On top of all that place large increasing demands for electric power and you have a potential beyond anything seen during the 1970s and 1980s. In 1988 the EEC steel industry operated at 90% and in 1989 at 92% of effective capacity. A surge in spot prices indicated that 92% was close to the ceiling. This pace moderated in early 1990 but any slack will probably be taken up rather quickly."

Jan 1, 1990

By G. Danha, S. Wabula, D. Glasser, D. Hildebrandt, N. Hlabangana

"Impact tests on single particles or a bed of particles are used to determine the fracture characteristics of particles. Many different techniques have been adopted in comminution in order to find ways of optimizing energy consumption in the size reduction process. In this paper, we apply one such method called the Attainable Region (AR) analysis technique to optimize the impact energy on a bed of silica particles. The attainable region is a fundamental approach that is equipment-independent and can be used to analyze breakage processes. The AR is defined as a set of all possible outcomes, for the system under consideration that can be achieved using fundamental processes operating within the system.INTRODUCTIONThe energy crisis in Southern African has reached such critical levels, that most cities in countries like Zambia, Zimbabwe, Lesotho, Swaziland and even South Africa are experiencing load shedding challenges lasting sometimes up to 18 hrs a day. Southern Africa is well known for its riches in mineral resources, and the economies of most states in this region are driven by the mining & mineral processing sector. With the emergence of small scale miners due to government empowerment policies, national energy providers have had to resort to power cuts mainly to domestic users in a bid to cope up with the huge industrial electricity demands.It has been estimated that about 4% of the total energy used in the world is consumed by the mineral processing sector (Fuerstenau & Lutch, 1999). Tomanec and Milovanovic (1994) estimated that milling alone accounts for more than 50% of the total power used in mineral processing, but this can rise to as high as 70% for hard or finely dispersed and inter-grown ores. Today, the greatest challenge in mineral processing is how to optimize energy input to the size reduction process (Dey & Das, 2013; Nomura & Tanaka, 2011), where it has been observed that only a small percentage (1.5%) of the total energy input really does the breaking (Khumalo et al., 2008) while the rest is consumed by the equipment concerned and lost to contacts that do not result in breakage. The immediate benefits of focusing research on the optimization of energy in size reduction operations in the mineral processing sector lies in potential savings on industrial electricity usage that may then be directed towards domestic users."

Jan 1, 2016

By D. L. Churcher, R. J. Perry

"In recent years much work has been don e to examine alternate underground backfill support systems with the objectives of improving ground support and reducing mining costs. This report deals with the work conducted at Placer Dome Inc.’s Dome Mine to develop a high density backfill system, taking advantage of the unique properties of this fill material, to address a backlog of large open stopes to sustain stable minewide ground conditions for future generations of Dome miners.IntroductionDome Mine began its existence in 1909 with the discovery of visible gold on a dome shaped outcrop located west of Porcupine Lake in northern Ontario. The orebody beneath this outcrop has supported one of Canada’s premier gold mining operations for 80 years. Production during this time of over 46 000 000 tons of ore has resulted in the recovery of II 500 000 ounces of gold and 2 000 000 ounces of silver. Mining continues today at a production rate of 3500 tons per day, with ore coming from both underground and open pit operations.During the life of the mine, different underground mining methods have been used to extract the ore from a complex deposit consisting of single and multiple vein structures.Cut-and-fill mining was introduced in the 1930s using sand fill and later hydraulic fill for support and to provide a working platform. A total of 1 800 000 tons of sand fill and 7 300 000 tons of hydraulic fill have been placed underground in cut-and-fill stopes. Until the late 1960sshrinkage mining was used extensively, particularly in narrow, steeply dipping zones. Bulk mining with small diameter longholes was introduced about this time, to take advantage of low production costs. Longhole blasting has often been used to recover low grade ore from the walls or sills of old shrink stopes, resulting in large open stopes. Backfilling of these open holes has been restricted to smaller stopes and associated with local ground conditions.In the late 1970s it was recognized that the number of large open holes which were being generated presented serious regional and minewide stability problems for future operations. With higher gold prices, economic ore reserves were being tied up in areas adjacent to multi-level open stope complexes. To stabilize these stopes and allow access, backfilling would be required."

Jan 1, 1990

By S. H. Lucas

"This paper describes the development and application of single-stage fluidized bed continuous ion exchange to the following processes: removal of base metals from mine water; cyanide removal from gold mill waste; uranium removal from sulphuric acid leach liquor; and uranium removal from mine water. IntroductionThe recovery of metals by fixed bed ion exchange has been practiced for many years. However, the operation has been semi-continuous and can only treat clarified liquors. Substantial savings could be made if the operation were continuous, thus reducing the resin inventory, and if the costly filtration and clarification steps could be eliminated. Work has been in progress over the past twenty-five years on the recovery of metals from unfiltered ore leach slurries, heap leach liquors and mine drainage waters containing a small amount of suspended solids. In the case of dilute waste solutions, with suspended matter and high flow rates, filtration is usually prohibitively expensive.Continuous ion exchange operation using fluidized beds has made it possible to reduce considerably the resin inventory and to allow the treatment of unclarified liquors and slurries. The subject has been reviewed on several occasions (1. 2. 3, 4). Although fluidized beds in multi-stage columns are an improvement over previous resin-in-pulp treatment, they have complicated internal structure and I or involved automatic control systems to move the resin stages.Slater and Prud&apos;homme performed studies on multi-stage fluid beds, and concluded that the performance of single, deep fluidized beds of resin with continuous or semi-continuous flow of both phases would be worth investigating, particularly in the case of very dilute metal solutionsoi, A pilot plant was designed and built at CANMET in a cooperative project with Dr. Slateroi. The use of deep fluidized beds of resin (with a large height/diameter ratio) for treating dilute solutions has the attraction of engineering simplicity. Extreme simplicity of equipment design is considered of paramount importance when treating, for example, mine waters at high flow rates, possibly of the order of several million gallons per day. This paper describes the development of the concept of single-stage fluidized bed continuous ion exchange arid reviews the pilotplant development of processes for the treatment of base metal mine water, cyanide waste water, uranium leach liquor and uranium mine water."

Jan 1, 1980

"One of the workhorses of the minerals industry is the autogenous grinding (AG) mill and its derivative the semi-autogenous (SAG) mill. These are relatively well understood, but not so Scrubbers. Scrubbers are mechanically of the same appearance/function, so what is the difference between an AG mill and a scrubber? When, or under what conditions should a scrubber be used and when should an AG mill be used? Can the processes within be mathematically modelled?In the past decades, the minerals industry has focused most of its attention on the modelling of unit processes such as cone crushers, HPGR’s, AG/SAG mills and ball mills within conventional processing circuits. Less attention has been placed on the modelling of scrubbers. This paper reviews the difference between scrubber and AG mill modelling, highlighting some of the similarities, with a view to confident comminution circuit designs.Engineering practitioners should be comfortable with these circuit designs and not shy away from considering AG mills for both small and large scale plants. AG mills can treat both harder or softer ore and scrubbers are for only softer ores. This paper differentiates scrubber and AG mill modelling in a similar way that overflow ball mills and grate discharge ball mills are analysed. Smaller scrubbers (600 kW) are suited to small scale soft ore (100-300 t/h) operations. Larger scrubbers up to 2,500 kW have the capability of very high throughput, in excess of 1,750 t/h with soft fine feed ore. AG mills are scalable up to 28 MW and are capable of treating harder ores at rates exceeding 2,000 to 4,500 t/h. Observations are that the specific energy requirements for the mill grinding duty is wide and varied. This is to a large degree the crux of the matter in sizing, as well as, differentiating, scrubbers from AG mills.INTRODUCTIONAG milling is a mature technology that has been used in minerals processing applications for more than 100 years. In the last 50 years, harder metalliferous ores have seen the introduction of steel balls to assist in the grinding/milling action. Tumbling mills used in such a configuration are called semiautogenous mills (SAG). The greater minerals industry is no newcomer to the use of fully autogenous (AG) mills. Perhaps scrubbers are. What is the difference? When should a scrubber be used versus an AG mill? How are they mathematically modelled?"

Jan 1, 2016

By J. Bensabat, B. Figueiredo, A. Niemi, J. Rutqvist, C. F. Tsang

"A hydro-mechanical model was developed to study the interaction between mechanical deformation and fluid flow in the fault zones during CO2 injection and storage at the Heletz site which was chosen as a test site for CO2 injection experiments in the framework of the EU-MUSTANG project. The potential reservoir for CO2 storage at the Heletz site consists of three sand layers separated by lowpermeability shale layers. The potential consequences caused by fault reactivation, focusing on the shortterm integrity of CO2 storage, are evaluated. The difference in the results obtained by considering the three-layer as an equivalent layer storage formation is analyzed.INTRODUCTIONLarge-scale storage of CO2 in deep underground reservoirs may cause considerable pore-pressure perturbation as well as flux migration and concern has been raised over whether shear slip displacements may be induced in nearby faults, as a consequence of their reactivation. A state-of-the-art review can be found in Rutqvist (2012), which describes the various possible effects resulting from CO2 injection into a deep sedimentary basin, including those involved in reservoir stress–strain changes, micro-seismicity, caprock sealing performance, and potential fault reactivation. Moreover, several studies have recently shown how CO2 injection may produce seismic events both on major faults (i.e., large faults with large initial shear offset) (Cappa & Rutqvist, 2011a, b, 2012), and on minor faults that might have gone undetected during the site characterization, e.g., faults less than 1 km long and without detected initial offset (Mazzoldi et al., 2012).The present paper is concerned with the Heletz formation which was chosen as a test site for CO2 injection experiments in the framework of the EU-MUSTANG project. The Heletz site located at the southern Mediterranean coastal plain of Israel and the structure is an anticline fold with a crest of about 4 km by 2 km. The structure is gently dipping to the east, truncated by a pinch-out line to the west and subdivided into a number of blocks by transversal normal faults with small displacements. The water table is located at 300 m below the land surface. An areal sketch of the site with the elevation of the caprock and the location of the borehole that has been chosen for the CO2 injection experiment is presented in Figure 1."

Jan 1, 2015