Search Documents

By A. Sacit Saydam

"Induced polarization/resistivity and magnetometer surveys have been carried out over the Casmo molybdenite deposit in mountainous terrain of northern British Columbia. Molybdenite occurs in quartz-bearing fractures with or without pyrite along a zone of hydrothermal alteration and intense fracturing, believed to be a northerly dipping fault zone, within medium-grained equigranular and porphyritic quartz monzonite.The molybdenite-bearing zone is characterized by a significant resistivity low, a metal factor high and a subtle IP low flanked by highs outside the mineralized area. Magnetic trends, indicated by a magnetometer survey, generally parallel the zone and strike direction of the different intrusive phases, and have been helpful in delineating contacts and faults in the area.IntroductionThe Casmo molybdenite deposit is 6 km southwest of the asbestos mining town of Cassiar in northern British Columbia, at an elevation of 1,550 metres. Molybdenite was first discovered during the early 1950s and the first important exploration work was done in 1964. Between 1964 and 1971, about 25,000 feet of drilling was done by various operators, as a result of which 33.7 million tons of molybdenite ore was drill indicated at a grade of 0.123%. In 1979, Shell Canada Resources entered into an option agreement with the former operator, New Jersey Zinc Corporation. Shell completed 27,000 feet of diamond drilling between 1979 and 1980 and ha s reported 75 million tonnes of drill-indicated ore with an average grade of 0.13% MoS2• This paper is a case history of IP I resistivity and magnetometer surveys done over the Casmo deposit during 1979 and 1980."

Jan 1, 1983

By E. Ghali, A. D. Bas

"Treatment of oxide, e.g. roasted gold ores has received relatively less attention than sulphidic ones and recently, handling of oxide gold ores is becoming essential. In this study, the influence of roasted gold ore (RGO) slurry (at 35% solid ratio) on the electrochemical dissolution of gold has been examined using pure gold and iron oxide minerals (hematite, maghemite, and magnetite) as disc electrodes by zeroresistance ammeter mode either in one or two separate containers. The presence of slurry decreased galvanic currents, i.e. corrosion rates due to the release and increase in the amount of soluble and/or insoluble species that could retard further the anodic behaviour of gold. Higher galvanic currents were observed in two separate containers than that in one container indicating the primary importance of galvanic interactions. SEM-EDS results observed iron hydro/oxide coatings on gold surface in case of magnetite test. However, in case of RGO electrode it is not a perfect passivation, although somewhat decreasing trend was observed on gold dissolution. These findings have revealed that passivation is not only a laboratory phenomenon, but also it could be responsible for the slowdown of gold dissolution in industrial practice.INTRODUCTIONThe cyanidation of gold is an electrochemical corrosion process thus; the dissolution of gold can readily be studied by electrochemical techniques. The outcome/summary of previous electrochemical studies of gold leaching can partially be summarized as follows: Filmer (1982) and Lorenzen and van Deventer (1992) reported the negative effect of pyrite and pyrrhotite on gold leaching due to the galvanic interactions; Aghamirian and Yen (2005) studied gold galvanic corrosion in presence of sulphide mineral electrodes only in one cell using zero-resistance ammeter (ZRA) mode; Dai and Jeffrey (2006) discussed, individually, the anodic and cathodic behaviours between gold and sulphide minerals, and Azizi et al. (2010, 2011) used a bed reactor to examine the influence of sulphide minerals on gold dissolution in one and two separate cells. Accordingly, a slowdown in gold leaching has generally been attributed to the passivation phenomenon, although the indication of this phenomenon is still an undergoing debate. For instance, Mrkusic and Paynter (1970) identified the passivation as the film formation of dissolved species from calcine, Crundwell (2014) explained passivation, in the case of corrosion of metals, as the formation of a layer which is composed of a new chemical species on the mineral surface and this layer inhibits or blocks further reactions. He suggested that passivation is related to the oxidation of the metal, and the formation of a passive layer that retards the rate of dissolution by several orders of magnitude. Consequently, galvanic interactions, passivation phenomena, or combinations of them are considered significant electrochemical factors affecting gold dissolution (van Deventer, Reuter, Lorenzen, & Hoff, 1990; Azizi, Petre, & Larachi, 2012). It is important to note that generalizing the influence of a mineral/metal on gold dissolution may not be correct in all cases, since contrary behaviours/results (for pyrite) have been observed (Aghamirian & Yen, 2005). Therefore, electrochemical study of gold is still a subject of research and need to be examined further in detail."

Jan 1, 2016

By Mehmet F. Taner

"Abstract - "Les Mines Selbaie" is a large, generally low-grade, polymetallic (Zn, Cu, Ag, Au) "giant" volcanic-associated ore deposit in the Harricana-Turgeon belt, which is part of the northern Abitibi Subprovince of Quebec. Economically recoverable mineralization occurred in three zones: the A1 (open pit), A2, and B Zones (underground). The pre-mining resource was 54.9 Mt, including 8 Mt of sub-economic, locally silver-rich massive pyrite. In the Selbaie region, calc-alkaline andesitic volcanics form the "basement." The Brouillan Volcanic Complex formed within an islandarc setting on this regional basement. Evolution of this complex involved the formation of a felsic magma chamber and the development of a large caldera structure over the Brouillan batholith. Second- order linear and sub-parallel faults and rifts developed as a result of back-arc rifting/extension. The edges of these rifts were feeders for linear felsic volcanism (similar to fissural volcanism). During felsic volcanism, the feeder zones acted as conduits for hydrothermal fluids with associated pervasive potassic alteration. The alteration is characterized both vertically and laterally by well-defined quartz, sericite, K-feldspar and/or, locally, biotite halos, to produce a mushroom-shaped morphology. This K-feldspar alteration is not common in most other volcanic-associated ore deposits. Mafic dikes cut all of the geological units and appear to occupy earlier synvolcanic structures. Regional greenschist- assemblage metamorphism and pervasive deformation affect all units. Thrust faults moved part of the Brouillan batholith and basement units over the Mine Sequence. Although there is no relationship between the earlier mineralizing events and these late thrust faults, the thrust faults probably played an important role in location of ore lenses. Three types of mineralization are present: 1) copper-rich veins and hydraulic breccias; 2) disseminated and stringer, low-grade and high volume zinc-copper mineralization; and 3) finely laminated, massive, locally silver-rich pyrite mineralization within structural basins. At the bottom of these basins and at the contact of welded acid tuff (WAT) units, massive pyrite zones are locally enriched in zinc, and contain the possible vestiges of black smoker-like material. The ore metals were probably derived from leached basement andesitic volcanics in a hydrothermal system powered by one or more heat sources within the Brouillan Volcanic Complex. The Selbaie deposits are mainly characterized by: (1) the presence of small volcano-tectonic subsidence basins, which host chemical sediments and volcaniclastic materials; (2) pervasive potassic alteration; (3) locally high-grade silver mineralization (up to 1-2 kg/t Ag); and (4) the presence of random zones of Pb mineralization. The Selbaie deposits can be closely compared with the copper-rich Murgul deposits, which belong to the eastern Pontides metallogenetic province in Turkey. If conventional classification criteria for the volcanogenic massive sulfide deposits (e.g., Noranda, Mattabi types, and recent subsea floor deposits) are taken into account, the Selbaie deposits still exhibit many differences in terms of alteration assemblages, physical volcanology and some styles of mineralization (low-grade and large volume). Consequently, the "Selbaie" deposits belong to a new sub-type of volcanic-associated sulfide deposit, which may be used in future exploration programs."

Jan 1, 2000

By Robert B. Parsons

"The mining industry is adjusting its sights to take a shot at the rising level of non-profit taxes which threaten to handicap the industry 's competitive advantage. In the case of this particular expedition, the industry evidentally has a strong ally - the country's mines ministers. It appears that an initiative is under way to assess the impact of non-profit taxes on mining in Canada as compared to other mining nations.IntroductionSeventy-five years ago, Canadians were unceremoniously introduced to something called income tax. Since then, income tax has been identified as the source of countless evils ranging from the common cold (attributed to stress) to the demise of the economy. Some years later, the provinces jumped on the bandwagon with their own income taxes, and later on with mining taxes. These profit-based taxes had some appeal to elected officials and to a segment of the populace. The onus of the taxes varied directly with the ability to pay (in theory, at least). Previously, the principal sources of government revenues had been property taxes and customs duties, which were viewed as possibly being somewhat regressive in nature.The mining industry has always had concerns about different aspects of income and mining taxes - the tax rate is too high or the depreciation rate is too low, and so on. Recently, though, the industry has turned its sights on the expanding array of taxes which are not based on profit, including payroll taxes, capital taxes, water taxes, sales taxes, fuel taxes, property taxes, environmental levies and user fees. The industry is seriously concerned that the rising level of non-pro fit-based taxes is not only hampering the industry 's ability to reinvest in Canada, but is also placing Canada at a disadvantage in terms of trying to attract new investment capital."

Jan 1, 1992

By Chester J. Kuryliw

"The Geology of the Cochenour Willans mine, Red Lake district, was described by J. P. Nowlan in the Jubilee Volume. The complexity and intense alteration of the rocks obscured any clear relationship between ore and structure, and Nowlan recognized that future work might greatly modify the ideas then existing. This has proved to be the case. Subsequent detailed work has established the stratigraphic sequence in the Keewatin formations which are the host rocks of the orebodies, and has shown that the principal orebodies are confined to two adjoining bands of tuff.On this basis, it is now possible to map the complex structures with greatly increased accuracy. The amount of drilling and underground exploration required to find new ore has been much reduced, and indicated ore reserves are now substantially greater than at any time in the past. Daily production in 1955 averaged 187 tons per day at 0.578 ounces of gold per ton.The sequence of Precambrian events in the mine area is summarized in the following table:Intrusion of post-ore dykes.Ore formation.Intrusion of post-faulting, pre-ore dykes.Deformation: folding and shearing; alteration; faulting.Timiskaming sedimentation.Unconformity.Keewatin: volcanics and sediments, host rocks of the orebodies, described in detail in the next section.KeewatinFrom oldest to youngest, the Keewatin rocks in the mine area can be divided into six formations, which have been given local names:“Grey"" LavaA fine-grained dacitic to andesitic lava, amygdaloidal and locally containing well formed pillows. Certain areas are sheared and chloritized to a degree that makes identification difficult. The rocks are carbonatized throughout; the most persistent carbonate veins parallel the upper contact. Thickness more than 1,000 feet. (Minor mineralization, type 1 I -See section on Ore Formation)."

Jan 1, 1949

By D. R. Rice

"The Smoky Valley Common Operation is managed and 50 percent owned by Echo Bay Mine' s Round Mountain Gold Corporation. The other partners with 25 percent each are Homestake Mining Company and Case Pomeroy. The operation in central Nevada includes an open pit, 3-stage open-circuit crushing train and heap leaching on asphalt pads. Presently, about 18,000 tons per day of 0.039 troy ounce gold per ton are transferred to the leach pads, and a similar tonnage of leach residue is transferred to a waste dump. One million tons of ore are being leached at any one time.Gold and silver cyanide are adsorbed from pregnant leach solution on activated coconut shell carbon granules. Pressure stripping desorbs values from loaded carbon to electrowinning solution.Three electrowinning cells are operated in parallel. Each contains six cathodes. Each cathode includes about 40 troy ounces (2.7 pounds) of Number 2 medium coarse steel wool. The wetted area of each cathode is about 24 by 30 inches. Solution flow is 2 to 3 gallons per minute per electrowinning cell. Average current flow is 25 amperes per cathode. The voltage is controlled in the range of 3 to 4 volts to maintain desired amperage.Twice a week two cathodes are pulled from each cell and drained. Each cathode is split into four portions. These are put in a steel pan coated with WD-40 and dried overnight.Each dried cathode portion is put into a paper sack. Each group of four sacks corresponding to a cathode is weighed together. The typical weight ratio of loaded cathode wool to new cathodes is 9 or 10 to 1. To each sack is added 35 troy ounces of silica, 45 troy ounces of anhydrous borax, 35 troy ounces of nitre, and 5 troy ounces of fluorspar. The sacks are taped shut."

Jan 1, 1986

By M. Proulx

"RÉSUMÉ Le diagramme ternaire Al2O3-Sr-Y est un nouvel outil servant à l’exploration de gisements de sulfures massifs volcanogènes (SMV) archéens. Le diagramme permet de discriminer entre les roches volcaniques à minéralisations à zinc dominant (domaine Zn+) et celles à minéralisations à cuivre dominant (domaine Cu+), ainsi que les roches volcaniques ayant subi une chloritisation hydrothermale pouvant aboutir à la formation de chloritites associées aux cheminées d’altération (domaine Cl+). Ces trois domaines délimitent des zones d’influence géochimique ou d’empreintes hydrothermales résiduelles ou fossiles produites par les cellules de convection hydrothermales générées par des magmas. Le diagramme permet aux sociétés d’exploration de déterminer de façon peu coûteuse la fertilité potentielle des roches volcaniques archéennes en ayant recours à leurs bases de données et aux résultats de leurs analyses de terrain, sans aucune manipulation des données. Le diagramme ne s’applique pas aux SMV aurifères.ABSTRACT The tertiary diagram Al2O3-Sr-Y is a new tool to explore Archean volcanogenic massive sulphide (VMS) deposits. The diagram can be used to discriminate between the volcanic rocks where zinc is the dominant mineralization (Zn+ domain) and the rocks where copper is the dominant mineralization (Cu+ domain), as well as the volcanic rocks that were subjected to hydrothermal chloritization that could have led to the formation of chloritites associated with alteration chimneys (Cl+ domain). These three domains define the zones of geochemical influence, or residual or fossil hydrothermal footprints produced by hydrothermal convection cells generated by magmas. Exploration companies can apply the diagram to determine, at low cost, the potential fertility of the Archean volcanic rocks by using their databases and the results of their field analyses, without any data manipulation. The diagram does not apply to gold-bearing VMS deposits."

Jan 1, 2015

By Andrew Neale, Len Anderson, Rob Perry

"P.T Freeport Indonesia's new SAG mill commenced operation in February 1995. The reclaim system consists of four apron feeders and a series of three conveyors. The feeders are used in various combinations and relative speeds to blend SAG mill feed. It was recognized during design of the control system that effective automatic control would require dead-time and gain compensation. The successful implementation of the Dahlin algorithm to provide variable dead-time and gain compensation is described and compared to Pl control.RésumeL'opération du nouveau SAG de P.T. Freeport Indonésie a commencé en Février 1995. Le système de réclamation du minerai comprend 4 alimentateurs à tablier et une série de 3 convoyeurs. Les alimentateurs sont utilisés dans une combinaison variée et à des vitesses relatives différentes pour mélanger l'alimentation du SAG. II a été reconnu pendant la conception du système du contrôle que le contrôle automatique demandera une compensation pour le temps de délai et le gain. L'implantation de l'algorithme de Dahlin a été un succès et ii est comparé avec le contrôle Pl.ResumenP.T. Freeport Indonesia inició la operación de un molino semi autogeno (SAG) en febrero de 1995. El mineral es alimentado desde cuatro alimentadores tipo apron feeders y una serie de correas transportadoras. Los alimentadores se utilizan en variadas combinaciones y velocidades para mezclar apropiadamente el mineral que alimenta al molino SAG. Durante el diseño del sistema de control se detectó que el control automático requería de un tiempo muerto y compensaci6n de ganancia. En este documento se describe la implementación del algoritmo de Dahlin, que ha sido exitosa y ha permitido proveer tiempos muertos variables y compensaci6n de ganancia. Ademas se hace una comparaci6n con el Pl de control."

Jan 1, 1996

By M. A. Vos

"Cretaceous sands and clays underlie an area of approximately 5,000 km2 in Northern Ontario, southwest of James Bay. The deltaic deposits occur as a wedge of continental sediments to the north of an east-trending fault scarp referred to as the Precambrian Escarpment. They rest on older sedimentary formations of the Moose River Basin (Jurassic, Devonian) and are covered by glacial tills and marine sediments of the Quaternary period. Outcrops are restricted to occasional exposure in the deeply incised riverbeds.In 1975 and 1978, drill programs sponsored by the Ontario Government provided new information on the extent and quality of the deposits. Fourteen holes at approximately 12-km intervals were drilled to a maximum depth of 189 m by reversed- circulation chip drill methods. Some core was obtained as well. Analytical results show that the thickness of Cretaceous deposits exceeds 100m in several instances. Abundant kaolinitic clay and quartz sand of glass-grade quality, both unique materials in Ontario, are available in an area where hydroelectricity and lignite resources combine to enhance the energy outlook.IntroductionThe presence of refractory clay in deeply incised riverbeds in Northern Ontario was known to geologists travelling the rivers as early as 1875. Robert Bell (1877) reports outcrops of clay and lignite on Coal Brook, a tributary of the Missinaibi River. E.B. Borron in 1880 collected a sample of clay from the bed of the Missinaibi River which H.H. Croft of the University of Toronto considered to be ""nearly if not quite, equal to the Cornish clay used in the manufacture of English porcelain"" (Keele, 1920, p. 42). The Cretaceous age of the clay, sand and lignite deposits was determined with the help of plant remains collected by Keele. He referred to the deposits as the Mattagami series, which later became the Mattagami Formation."

Jan 1, 1982

By A. Abadías Llamas, N. Bartie, M. Stelter

Evaluating the economic viability as well as the sustainability of the Circular Economy (CE) system requires a deep understanding of the distribution of all elements, compounds, alloys, materials etc. in flows. In this paper, the circularity of the copper value chain, including primary and secondary processing, is rigorously evaluated. The studied system comprises the metallic copper production from primary sources (from mineral to metal), copper-containing commodity production (copper is mixed with other metals) and copper recycling through secondary smelting to close the loop. This is linked to photovoltaic (PV) panels and battery storage. A simulation model of this system is created using HSC Sim, considering more than 30 elements (and its various compounds), 180 unit operations and 800 flows. From the mass and energy balances obtained through the simulation, an exergy analysis is conducted to evaluate the resource consumption from a second law (entropy) perspective. Additionally, these results are complemented through a Life Cycle Assessment (LCA), the recovery of technology elements and by-products is discussed, while quantifying the losses through the value chain. Through the digitalization of the complete system, a better CAPEX and OPEX understanding of the metal recovery and losses can be obtained, as well as the associated resource consumption and environmental impacts. New flowsheets and technologies can be evaluated. Several scenarios show how the resource consumption and the environmental impacts are affected by the recovery of different materials to produce different products. INTRODUCTION A key challenge of the circular economy (CE) is the linkage and optimization of both resource and energy efficiency of the (renewable) energy infrastructure and the resource cycle depicted by Figure 1 simultaneously. In addition, the CE requires the linkage of all stakeholders as shown by Figure 1. This has been discussed in some detail by Reuter and Bartie (2019) and Reuter et al. (2019). Copper and all its associated technology elements is one of the key enabling metals that is an economical copper colored thread through CE society (Reuter & Kojo, 2014). The Metal Wheel (Figure 2) shows the linkage of and recovery of various elements associated with copper and other carrier metals. This reveals that copper acts as an important carrier metal because of its properties i.e. the wealth of technology elements it carries from geological ores, but also its capacity to act as solvent of valuable elements and thence a key closer of various complexly connected element and material cycles when these technology elements are released during copper refining. The same applies to all other carrier metals of modern CE society as shown for example recently in a lead policy brief (Blanpain, Reuter & Malfliet, 2019).

Jan 1, 2019

By Mark W. Masson, David B. Stevenson, David W. Broughton, Douglas R. Cruji, Steven E. Parry

"Abstract-The Amalgamated Kirkland gold deposit is located at Kirkland Lake, Ontario, within the Archean Abitibi Greenstone belt of the Canadian Shield. It lies on a fault or "break", termed the Cyprus Break, which is a splay off a regional structure termed the Cyprus-Battle Mountain Break. The Cyprus Break merges with the Cyprus - Battle Mountain Break above the -250 m level, as it was not encountered in shallow drilling or surface exploration. These structures lie 1.5 km south of the 727 000 kg (23 million ounce) Kirkland Lake Main Break and 0.5 km north of the 872 000 kg (30 million ounce) Larder Lake Break.The deposit is hosted by alkalic Timiskaming Group volcanic and sedimentary rocks which are overthrust by older Larder Lake Group tholeiitic and komatiitic flows along the Larder Lake Break. Timiskaming syenitic intrusives, similar to the host rocks for the Kirkland Lake Main Break gold deposit, intrude both suites.The Amalgamated Kirkland deposit consists of lode-style gold mineralization which is mainly hosted by altered and pyritized Timiskaming trachytic volcanics which wedge out or thin at depth, between two sedimentary units. The intersection of the Cyprus - Battle Mountain and Cyprus Breaks, in conjunction with the westward plunge of the volcanic wedge, appears to control the westerly plunge of the Amalgamated Kirkland deposit at approximately 50º.Mineralization is characterized by blue-gray brecciated and "wormy" quartz-ankerite veins which contain up to 10% fine-grained pyrite and, in decreasing order of abundance, minor galena, chalcopyrite, sphalerite, molybdenite and visible gold. The sulfides and gold commonly occur along fractures and wallrock inclusions within the veins. Native gold occurs as fine pinpoints distributed in 1-mm to 5-mm size clusters of up to ten or more grains.The auriferous veins occur within a quartz-ankerite-sericite-pyrite alteration assemblage which is enveloped by a broader zone of ankerite-sericite±hematite±quartz-pyrite alteration up to 60 m wide. This latter assemblage overprints the regional greenschist-facies chlorite-calcite assemblage.The Amalgamated Kirkland property has had a long history of exploration activity beginning with the first discovery of mineralization in 1911 on the Hunton Shaft claim located in the northeast corner of the property. Since that time various prospecting, mapping, trenching, geophysical surveys and diamond drilling programs have concentrated on either carbonate zones along the Larder Lake Break or quartz veins along the northern side of the property in association with complex trachyte flows and syenite dikes.Battle Mountain Canada Inc. located the Cyprus - Battle Mountain Break through a prospecting, trenching and geophysical program in 1989. Drilling by Battle Mountain and Cyprus Canada under the surface showing, coupled with several revisions to the structural interpretation of the Cyprus - Battle Mountain and Cyprus Breaks, resulted in delineation of the Amalgamated Kirkland deposit. Location of an auriferous structure through basic surface exploration within 1 km of a world-class orebody demonstrates both the subtle nature of Archean gold deposits and the potential for finding new mineralization in heavily prospected camps."

Jan 1, 1995

By Mark W. Masson, David B. Stevenson, David W. Broughton, Douglas R. Cruji, Steven E. Parry

"The Amalgamated Kirkland gold deposit is located at Kirkland Lake, Ontario, within the Archean Abitibi Greenstone belt of the Canadian Shield. It lies on a fault or “break”, termed the Cyprus Break, which is a splay off a regional structure termed the Cyprus-Battle Mountain Break. The Cyprus Break merges with the Cyprus – Battle Mountain Break above the -250 m level, as it was not encountered in shallow drilling or surface exploration. These structures lie 1.5 km south of the 727 000 kg (23 million ounce) Kirkland Lake Main Break and 0.5 km north of the 872 000 kg(30 million ounce) Larder Lake Break.The deposit is hosted by alkalic Timiskaming Group volcanic and sedimentary rocks which are overthrust by older Larder Lake Group tholeiitic and komatiitic fows along the Larder Lake Break. Timiskaming syenitic intrusives, similar to the host rocks for the Kirkland Lake Main Break gold deposit, intrude both suites.The Amalgamated Kirkland deposit consists of lode-style gold mineralization which is mainly hosted by altered and pyritized Timiskaming trachytic volcanics which wedge out or thin at depth, between two sedimentary units. The intersection of the Cyprus – Battle Mountain and Cyprus Breaks, in conjunction with the westward plunge of the volcanic wedge, appears to control the westerly plunge of the Amalgamated Kirkland deposit at approximately 50º.Mineralization is characterized by blue-gray brecciated and “wormy” quartz-ankerite veinswhich contain up to 10% fne-grained pyrite and, in decreasing order of abundance, minor galena,chalcopyrite, sphalerite, molybdenite and visible gold. The sulfdes and gold commonly occur alongfractures and wallrock inclusions within the veins. Native gold occurs as fne pinpoints distributed in 1-mm to 5-mm size clusters of up to ten or more grains.The auriferous veins occur within a quartz-ankerite-sericite-pyrite alteration assemblage which is enveloped by a broader zone of ankerite-sericite±hematite±quartz-pyrite alteration up to 60 m wide. This latter assemblage overprints the regional greenschist-facies chlorite-calcite assemblage.The Amalgamated Kirkland property has had a long history of exploration activity beginning with the first discovery of mineralization in 1911 on the Hunton Shaft claim located in the northeast corner of the property. Since that time various prospecting, mapping, trenching, geophysical surveys and diamond drilling programs have concentrated on either carbonate zones along the Larder Lake Break or quartz veins along the northern side of the property in association with complex trachyte flows and syenite dikes.Battle Mountain Canada Inc. located the Cyprus – Battle Mountain Break through a prospecting, trenching and geophysical program in 1989. Drilling by Battle Mountain and Cyprus Canada under the surface showing, coupled with several revisions to the structural interpretation of the Cyprus –Battle Mountain and Cyprus Breaks, resulted in delineation of the Amalgamated Kirkland deposit. Location of an auriferous structure through basic surface exploration within 1 km of a world-class orebody demonstrates both the subtle nature of Archean gold deposits and the potential for finding new mineralization in heavily prospected camps."

Jan 1, 1995

By John Starkey

This paper examines 5 years of SAGDesign testing data with particular emphasis on the grinding test results from two recent projects, the Fortune Minerals Limited NICO project, and the Aurora Energy Resources Inc., Michelin deposits, located in the Northwest Territories and in Labrador respectively. The context is to compare these results with the SAGDesign database. The required SAG mill pinion energy for these two ores showed vast differences, even though both ores had similar average Bond Ball Mill Work Index values - about 13 kWh/t each for the two deposits respectively. Bond Rod Mill Work Index values for NICO ranged up to 19.7 kWh/t for the hardest ore, confirming the harder nature of the coarse material. SAG mill pinion energy to grind the NICO cobalt-gold-bismuth-copper ore from F80 152 mm to T80 1.7mm varied from 16 to 35 kWh/t, while for Michelin uranium ore, it varied from 2 to 9 kWh/t. NICO ore is harder than any other material encountered to date using SAGDesign testing. SAG pinion energy is more than double the ball mill pinion energy using a transfer size T80 of 1.7mm and a final grind P80 of 74 microns. For NICO, the ore is ?off the charts? for simulation design techniques because there is no comparable operating SAG mill treating ore that is this macro-competent. For Aurora, the relationship between SAG and ball mill pinion energy is reversed in that the SAG mill requires less than half of the ball mill pinion energy using a transfer size T80 of 1.7mm and a final grind P80 of 90?. Because these discoveries are so important for grinding mill design, their impact will be dealt with in future papers, at the August METSOC Conference in Sudbury, and at the September SME Workshop in Tucson. It has now been concluded that the ratio of SAG pinion energy to Bond Ball Mill Work Index, is valuable data to use in designing a SAG/ball mill grinding circuit, to help choose the power split needed.

May 1, 2009

By BARRY BANNATYNE

About 90 per cent of Manitoba's industrial minerals production is for structural materials. Most of these come from the Paleozoic rocks west of the Precarnbrian Shield, or from glacial deposits that are extensive throughout Manitoba. The major raw materials are sand and gravel, and carbonate rocks for crushed stone (and also dolomite for high-magnesia lime, high-calcium limestone for lime and Portland cement, and dolomitic limestone for Tyndall stone). Glacial lake clays are used both in cement and in lightweight aggregate. The Jurassic and Cretaceous strata exposed along or near the Manitoba Escarpment include siliceous, carbonaceous, kaolinitic and illitic shales, all of which are quarried by Red River Brick and Tile in the Pembina Mountain and Ste. Rose areas for use in a brick plant at Lockport. Non-swelling bentonite near the base of the Pembina Member of the Upper Cretaceous Vermilion River Formation is of value as an absorbent clay, and is the only commercial source in production in Canada. It has been quarried by Pembina Mountain Clays Limited since 1940. Gypsum occurs in the Jurassic Amaranth Formation and supplies much of the market for wallboard and Portland cement additive in the Prairie Provinces. Quarries are operated at Gypsumville by Domtar Construction Materials Limited, and north of Amaranth by Westroc Industries Limited. Silica sand from the Ordovician Winnipeg Formation is of glass-grade quality, and about 100,000 tonnes are produced annually by Steel Brothers Canada Limited on Black Island . It is used as a glass sand, as foundry sand, for sand blasting, and as a filter-bed sand .

Jan 1, 1984

By David W. Mogk, Tamara Darsow, Macgregor L. Fogelsong, Robert M. Hunter, Frank M. Stewart, Edwin H. Abbott, Courtney A. Young

Abstract: Development of cost-effective techniques for recovering precious metals from their ores has been the goal of metallurgists for hundreds of years. Today, metallurgists are increasingly called upon to design processes for ores that are refractory to conventional recovery techniques. These challenges and the addition of environmental costs (including site remediation) to the total cost of mining have stimulated a search for alternatives to conventional processes, such as cyanidation. This paper describes the progress made to date in development of an innovative alternative to cyanidation, termed bisulfide leaching, for extracting gold, silver and platinum-group elements from refractory ores and concentrates. While bisulfide leaching can be implemented abiotically, significant benefits accrue from its practice as a bioprocess that integrates the steps of precious-metals liberation and extraction. In many applications, bisulfide leaching appears to offer significant advantages over the traditional cyanidation process. Dissolved bisulfide and hydrogen sulfide are much less toxic than dissolved cyanide and hydrogen cyanide. Recommended workspace exposure limits and harmful concentrations for hydrogen sulfide gas are higher than those for hydrogen cyanide gas. While the facilities required to practice the bioprocess on an industrial scale would be similar to that of cyanidation plants, chemical reagent costs could be 80 percent less. The bioprocess may also offer advantages in the leaching of ores and concentrates that are not amenable to cyanidation. For example, bisulfide leaching of ores containing carbonaceous material may produce higher gold recoveries if the "preg-robbing" characteristic of the material can be controlled biologically or with dissolved sulfide binding. Moreover, in that precious metals are much more soluble than base metals in bisulfide solutions, bisulfide leaching offers distinct advantages over cyanidation for selective dissolution of precious metals from base-metal concentrates. Thus, the bioprocess uses the natural sulfur cycle to mitigate pollutant production and to enhance precious-metals recovery.

Jan 1, 1998

The hydrometallurgical treatment of copper ores and concentrates continues to be an active field of innovation. The direct extraction of copper from ores containing chalcopyrite is an important development to provide an alternative to flotation-smelting and refining. Jetti Resources (with the University of British Columbia) and the JX Nippon Group have developed process options for chalcopyrite heap leaching. Biological heap leaching developments for chalcopyrite are also continuing in parallel. These direct leaching technologies are also very attractive for arsenical ores. The atmospheric leaching of copper concentrates is an attractive option along with autoclave processing. The Galvanox™ Process is the focus of commercialization by InCoR Galvanox Holdings under exclusive license by the University of British Columbia. The Galvanox™ Process can be used to treat chalcopyrite or enargite containing concentrates to high copper extraction with simultaneous precipitation of arsenic as atmospheric scorodite. FLSmidth has continued development of the Rapid Oxidative Leach (ROL) and associated technologies for chalcopyrite leaching. The Glencore Albion Copper Process using ultra fine grinding of copper concentrates and atmospheric leaching has found application in central Africa. The pressure leaching of copper concentrates continues to be attractive for rapid, complete oxidation of sulfide minerals with high copper extraction and arsenic stabilization of iron-arsenate minerals and precipitates. The Ecometales PLCC project is designed to use high temperature total pressure oxidation for treatment of an arsenical copper concentrate with use of existing copper SX-EW facilities for copper cathode production. The excess acid from the autoclave process will be used to make up the acid demand for associated copper ore heap and dump leaching operations. INTRODUCTION The recovery of copper from ores is dominated by the flotation of copper concentrates followed by smelting—converting and electrorefining. This process has been enabled by the development of froth flotation and progressively made more efficient by advances in smelting and converting technologies.

Jan 1, 2019

By Vincent H. Hartung

The process of estimating tailings deposition for a given basin is a relatively tedious process without dedicated software tools. The amount of time required to generate a tailings surface for a given set of conditions tends to limit the number of design alternatives that can be considered for a particular project. Recent innovations in the Surpac Vision mining software include the widely used scripting language TCL (Tool Command Language) that brings with it the ability for non-programmers to extend the software functionality beyond mining applications alone. A software tool was developed using the Surpac Vision scripting language to take advantage of 3D visualization and create a flexible tailings modeling solution. The result is an application that removes much of the drafting overhead required to produce a tailings surface. It provides the means for reviewing alternatives and performing sensitivity analysis with variables such as pond elevation, dam or spigot location and height without a significant increase in overall time for a project.

May 1, 2001

By H. H. Wober, P. J. Morgan

"The proposed classification of ore reserves based on geostatistical and economic parameters is designed to be used as a communication tool to identify for investors, bankers, and financial analysts the degree of risk associated with a specific class of ore reserves. The class designation identifies the degree of accuracy of the estimates for tonnage and grade of annual production volumes of ore. It thus enables decision makers to quantify the risks and uncertainties inherent to the ore reserve in achieving over-all economic goals and annual financial objectives.IntroductionDuring the evaluation, in 1980, of the Creede silver deposit in Colorado, U.S.A., as a potential bulk mining project, the authors were faced with the problem of conveying to senior management the risks and uncertainties that are implied by using common or conventional classification systems to categorize ""ore reserves"". The estimated numbers for tonnages and grade of the projected ore reserves represented the only entry for future revenue from the project. It was, therefore, necessary to convey to management the level of risk associated with those numbers when implementing further stages of development, and to convey what impact significant differences would have on the profitability of the project. The desire to quantify these risks led to a revised definition of ""ore"" and to a re-examination of the classification system of ""ore reserves"". Traditional methods for estimating tonnage and grade of reserves do not include a quantification of the errors of these estimates. The advent of geostatistical methods made this quantification possible. The proper application of geostatistical methods, with adequate geological input and a reliable set of sample data, is essential to its validity.Others have proposed a classification of ore reserves based on geostatistical parameters. Diehl and David (1982) recognized ""that concepts of proven, probable and possible have to be linked to the production rate or time horizon"". Royle (1977) had also addressed this problem. Forsyth (1987) pointed out that bankers are concerned with ""the probability that the variability will fall within a certain degree of accuracy"" especially for grade estimates, and would like to see grades expressed together with the error of the estimate at the 950Jo confidence level."

Jan 1, 1993

By G. E. Wood

THE INSTABILITY of copper prices and their low levels since late 1974 are of great concern to both producers and, to a lesser degree, consumers of copper. The price levels portrayed by the "neutral long-term" price trend are assumed to have been enough to encourage sufficient investment to provide adequate world production capacity and yet not so high as to encourage development of excessive over capacity. The identification of the present level of this trend has taken on special importance for governments and for corporations active in the world copper industry. One approach to the possible determination of such a price is through the use of moving averages. In this way, the effects of relatively short-term price movements can be dampened, as can those related to business cycles. From such averaged price data, long-term trends can be sought over a selected time period. The choice of the past time period for which a price trend is sought may have a major effect on the result'. For example, in the period 1885-1973, the long-term price trend for copper in constant dollars showed a decline, whereas in the period 1919-1973 it was rising. For the purposes of discussion, an appropriate choice of period might be a relatively short and recent one so that the majority of the present cost factors would be present throughout. It should also be long enough to cover a number of full business cycles.

Jan 1, 1977

By R. B. Roberts, A. L. Mular

A simple way to determine the IEP of oxide minerals is described. The method is shown to apply for fine powders of Fe203 and ZnO. The IEP lies at pH 6.95 for Fe203 and at pH 9.08 for ZnO.

Jan 1, 1966