Search Documents

By Ernest A. Hodgson

WHEN excavations are made, at depth, in hard brittle rock structures, as in certain mines in India, in South Africa, and in Ontario, the pressure due to overburden, together perhaps with inherent geologic strain, tends to become concentrated in the walls of some of these openings and the rock bursts, often closing the adjacent drifts and scopes and presenting a serious menace to the miners. Where the rock is much fractured and faulted, the danger is greater, since the pressures tend to shift without warning from point to point, sometimes within a few hours. Attempts have been repeatedly made to find some physical property of the rock which will change with pressure, which can be measured for rock 'in place' in the mine, and which will give an indication of the state of strain, thus warning of an approach to bursting conditions. Some of the properties tested have been the speed of propagation of elastic waves in the suspect rock, variations in temperature due to pressure changes, rate of closure of openings or shifts along fault planes, strain gauge measures, and others. Each of these has proved unsatisfactory for the purpose. The most promising method so far proposed has been the study of the very faint, sub-audible snaps (microseismims) which are produced in rocks under pressure. Such a study has been in progress at Lake Shore Mines since May, 1942. Instruments designed to pick up, amplify, and record the microseismims were perfected and a programme of observing, using the microseismic method, has been carried through with persistent diligence and at considerable expense. In 1943, experience with the method in a pillar section on the west side of the Lake Shore mine gave much promise of predicting bursts. A very heavy burst on January 29th of that year occurred in the exact section of the mine covered by the instruments, and the records indicated a measure of prediction. In response to repeated requests for information, a number of reports were given out, among others a radio talk by the writer over CJKL (Kirkland Lake), which was reported in full in the Northern News . Also, a detailed account of the occurrence was given in an illustrated paper by the writer (l).

Jan 1, 1945

"“Developed by the CIM Sub-Committee, these guidelines are an addition to Guidelines Specific to Particular Commodities which are appended to the CIM Estimation of Mineral Resources and Mineral Reserves Best Practice Guidelines.Rock Hosted DiamondsJennifer Burgess, Consultant, Sechelt, BCNeil Buxton, WWW International Diamond Consultants Ltd.Darren Dyck, BHP Billiton Diamonds Inc., Kelowna, BCMartinus Oosterveld, (De Beers retired), Plettenberg Bay, South AfricaRichard Routledge, Scott Wilson Roscoe Postle Associates Inc., Toronto, ONMalcom Thurston, De Beers Canada, Toronto, ONPreambleDiamonds are produced commercially from intrusive rock, consisting of kimberlite and lamproite, and from alluvial and marine placer deposits. These guidelines apply to rock deposits; the term ""diamonds"" herein refers to natural diamonds; ""diamond deposits"" refers to diamonds hosted in kimberlite and lamproite rocks; and ""diamonds"" and ""stones"" are interchangeable.The CIM Best Practices General Guidelines for other commodities are also applicable to diamond deposits, however, because of diamond's distinguishing aspects, additional guidelines are appropriate as published in the CIM Guidelines for the Reporting of Diamond Exploration Results and these Best Practice Guidelines for estimating Mineral Resources and Mineral Reserves (MRMR).Diamonds differ from other minerals. Firstly, they occur as discrete particles in concentrations as low as parts per billion. Secondly, the release of diamonds from the kimberlite or lamproite host rock is a function of the excavation and treatment process. Thirdly, the value of diamonds varies from deposit to deposit and varies with stone size within a given deposit. These aspects must be considered when sampling, evaluating the resource and establishing the reserve of a depositThe product from metallic mineral mines is generally quite liquid in terms of number of potential buyers, and the commodity prices and price structure are published daily. In contrast, most diamonds are valued in the overall market context only 10 times a year in ""sights"" and the marketing of diamonds is dominated by a small number of organizations. Diamond valuation is more akin to industrial minerals valuation in that process recovery is important at the ""assay stage"", the impact on price of new goods arriving on the market must be evaluated, and product quality must be acceptable to potential buyers."

Jan 1, 2003

By Song (Bruce) Li

This paper presents a three-tier web-based GIS application that uses Java Server Page (JSP), Java Servlet and relational database to manage performance monitoring and reporting in the oil sands mining industry. It is a real-time Earth Structure Performance Monitoring System (ESPMS), which allows the user to record and store instrumentation monitoring readings as well as technical observations and instrumentation installation documentations into a complete relational database. The ESPMS introduces the advantages of precise field record keeping, due diligence, security, consistency and completeness while at the same time simplifying the task of reporting. ESPMS combines web-based Geographic Information System (GIS) mapping and data management to facilitate the collection, organization, retrieval, reporting and communication of the vast amounts of monitoring data related to mining and tailings engineering associated with site investigation and construction information. ESPMS utilizes web-based GIS technology to incorporate referenced aerial photographs, Energy, Mines and Resources (EMR) maps or AutoCAD drawings as a base map for the monitoring site. It dynamically creates and administers all instrumentation monitoring locations and reading frequencies. It enables the user to collect and manage the data associated with an unlimited number of reading events. It provides the designer with real-time monitoring data (what, why, when, how), thereby allowing them to make early adjustments to design protocols or procedures, or to take remedial action(s) regarding the subject earth structure under construction or after completion. It provides more cost-effective reporting and data sharing through the Internet. It improves security on data entry and eliminates unauthorized data changes. It allows better integration of graphics and illustrations with numerical data files. It is capable of managing the continually expanding workload resulting from new and larger structures in the oil sands or other mineral mining industries. The ESPMS facilitates easier data gathering for preparation of as-built and after-built or regulatory reports, etc. It enables quick location of the interested instruments and summarization of the performance of the instruments. It enables one to visualize performance data and QA/QC construction test results spatially on any given cross-section. Data can be exported to MS Excel for detailed analysis and to evaluate the stability of the earth structures.

May 1, 2004

By D. W. Smith, J. J. Koskinen, T. A. Enwald, M. E. Ball

"A full-scale demonstration unit of Tampella's LIFAC desulphurization process was tested at SaskPower's Poplar River Power Station Unit No. I. The test program included a series of parametric tests, followed by a 1500 hour operational evaluation. This paper summarizes the results of the test program, and SaskPower's economic evaluation which led to selection of the LlFAC process for SaskPower's 300 MW Shand power station. IntroductionOne of the major influences on the coal mining industry today is public and legislative response to acid rain. When sulphur-bearing fuels such as coal are burned, the sulphur oxidizes to sulphur dioxid e (S00 which, if uncontrolled, enters the atmosphere as one of the by-products of combustion. S02 then combines with water in the air to form an acid and acid rain results. Combustion also produces nitrogen oxides (N0J which can combine with water in the air forming nitrogen based acid , also contributing to acid rain.Acid rain has become a significant international concern. Newspapers have reported on dying forests, dead lakes and crumbling statues. Papers also include articles professing that the physical results of acid rain are vastly overstated. In the United States, a IO-year, Y2-billion dollar study called the National Acid Precipitation Assessment Program (NAPAP) was commissioned to evaluate the effects of acid rain. Even this extensive scientific study did not resolve the controversy. Despite disagreement over the quantitative effects of acid rain, there is no doubt that public concern over the issue is widespread and deeply felt.In response to this concern, legislators throughout the world have reacted with programs that restrict the emission s o f SO, and NO,. To industries involved in the supply and use of coal, the impact of these legislative programs has been extensive. United States power plants will be spending 10 billion dollars in the next decade for flue gas clean-up equipment. Even all this new equipment will not stem the tide of change to low sulphur coals and to “clean “natural gas. The following summarizes legislative actions taken for Canada and the United States."

Jan 1, 1993

By D. A. Whitley, R. P. Carone

"Shaft sinking by blind shaft drilling offers the mining industry a different approach to shaft construction. Benefits of blind drilling include less construction time and fewer safety problems while being economically competitive with conventional sinking methods under certain conditions in soft water-bearing formations.Technology and equipment are available today to drill blind shafts up to 20 feet in diameter and over 3,000 feet deep. This is an extension of proven techniques developed by private industry. To drill a 20-foot-diameter hole requires a specially manufactured hydraulic drill unit with a rated hoist of 2 million pounds and 500,000 ft/lb of torque.This brief paper will discuss the following aspects of blind shaft drilling:• benefits;• equipment f or drilling;• circulation methods;• circulation rates;• shaft alignment; and• progress rates to be expected.IntroductionShaft sinking by blind shaft drilling offers the mining industry an improved alternative method for shaft construction. The drilling of 20-foot -diameter shafts to depth s in excess of 3,000 feet can be done by utilizing equipment specifically designed and manufactured for this purpose. This equipment is a distant cousin, at best, to standard oil well drilling rigs. The actual configuration of these drilling machines will be discussed in a following section.To most people, the drilling of mine shafts may seem to be a new or at least recent technology. However, as early as the I920s, German and Dutch miners were drilling 24-foot diameter shafts for coal mines. What led ""miners to resort to drilling were ground conditions that still plague conventional shaft sinkers today: soft , water-bearing formations. The major drawback to these early attempts was a low penetration rate due to poor bit cleaning. This, however, was not the end of early shaft drilling activity. From 1936 to 1950, a number of mine shafts were drilled by the calyx or coring method. This method employs a bit with a large bore down the center. As it drills, it cuts a core. When 5 to 10 feet have been drilled, the core is removed. The disadvantages of this method were the time and work involved in breaking the core free, and it was inadequate in soft water-bearing ground."

Jan 1, 1981

By D. F. Sangster

"Eight volcanogenic massive sulphide districts in Canada and Japan, ranging in age from Archean to Miocene, were selected for analysis. The study revealed that: {I) each district has an average diameter of 32 km; (2) the districts contain 4 to 20 deposits each, with an average of /2 deposits; (3) the average total base metal content per district is 4.6 million tonnes, with a coefficient of variation of32%; (4) ranked in order of size, the largest deposit in each district contains, on average, 67% of the total metal and the second largest about 13 %. The remaining deposits range downward in decreasing proportions. Empirical observations such as these may be used f or evaluating the undiscovered potential of new districts as well as contributing to a better understanding of the distribution and genesis of this important class of base metal deposits. Previous WorkThe characteristic geological features o f volcanogenic massive sulphide deposits have been described by numerous authors over the past fifteen years and it is now widely accepted that these deposits comprise a major ""deposit-type."" In addition to these geological parameters, however, it is now becoming apparent that volcanogenic massive sulphide deposits show several distinctive grade-tonnage relationships. For example, Singer et al. (1975) demonstrated a slight negative correlation between copper grade and ore tonnage in their sampling of 146 volcanogenic deposits. In a study of 110 Canadian Precambrian deposits of this type, Boldy (1977) showed that the size of the modal deposit is 0.39 million tons, that of the median deposit is 1.40 million tons and the arithmetic average is 6.85 million tons. Moreover, Boldy's data show that the average grade of combined base metals (Cu + Zn + Pb) for each of the se three deposit-sizes is, respectively, 6.25%, 5.35% and 6.47%. Because the lead content of Canadian Precambrian volcanogeni c deposits is most frequently less than 1%, the total metal grade is effectively Cu + Zn . From Figure 2 in Bold y (1977), it can be seen that 83% of the deposits fall in the range of 0.l to 10 million tons ."

Jan 1, 1980

By C. Mattich, Å. Holmström, L. Hedström

"The fluidized bed at Division Ministro Hales (DMH) division of Codelco in Calama, Chile is currently the largest operating roaster for partial roasting of arsenic rich copper concentrates. The roaster converts the Mina Ministro Hales (MMH) enargite rich (Cu3AsS4) copper concentrates into calcine with a low arsenic content that is suitable for mixing with other copper concentrates feeding a flash furnace. The plant sets a new standard for the processing of arsenic rich concentrates, both from the quality of the calcine as well as the environmental performances. The process technology and expertise are based on the solid practical experience of treating arsenic rich concentrates from both the Boliden smelter and Outotec.The partial roasting process is located next to the mine and concentrator and includes a sulphuric acid plant with auxiliary equipment. The produced calcine has an arsenic content significantly below target and the residual sulphur meets the requirement of the flash furnace. The plant operates with high efficiency cyclones resulting in a low amount of calcine passing to the hot electrostatic precipitator (HESP). The small flow of HESP calcine dust can be combined with the low arsenic calcine and still meet the flash furnace feed arsenic requirements.SO2 formed during roasting is converted into sulphuric acid, while volatized arsenic is recovered in the wet gas cleaning section of the acid plant along with a large proportion of antimony present in the MMH concentrate. Arsenic is stabilized as calcium arsenate and sent to disposal at a specially prepared site.The present production rate (September/October 2015) is close to or higher than the original maximum design capacity of the plant.INTRODUCTIONMineralogyThe mineralogy of an ore and concentrate is important, since there is a direct link between roasting performance and concentrate mineralogy. The MMH concentrate has a good combination of minerals that makes the roasting process efficient and flexible. The main minerals are pyrite, enargite and chalcocite (Figure 1). The inert content is about 15% and consists mainly of silicate and alumina based minerals. The lead content is very low and this is desirable, since the presence of even a small amount of lead will cause a substantial increase of sintering during roasting."

Jan 1, 2016

Particles for heap leaching in conventional circuits are prepared using Cone crushers. Cone crushers are used to crush the ore to the size range between 12-25 mm for heap leaching operations. Leaching from these relatively coarse particles occurs only at the surface and in subsurface regions, which are accessible from the surface by cracks and pores. Since leaching is active in accessible areas, the method of comminution that forms multiple cracks and pores would offer an advantage for heap leach. An investigation was performed in this study to assess if the HPGR forms more cracks and pores than a Cone crusher. X-ray computed tomography (CT) was used to characterize the degree of cracks and pores formed by these two comminution devices that can be used for heap leaching feed preparation. In order to compare the effect of the comminution method on crack network generation, a bulk sample of the zinc ore was crushed by the HPGR at three different pressure settings (45, 95 and 120 bar), the sample ore was also crushed with a Cone crusher for comparison purposes. Products from the Cone crusher and HPGR experiment were then screened into five size fractions ((-25 +19), (-19+16), (-16+9.5), (-9.5+5), (-5+4.75) mm), Subsamples from the ((-25 +19), (-16+9.5), (-5+4.75) mm) size fractions were analysed. The spatial distribution of the crack network of sphalerite particles was characterized using a highresolution industrial X-ray CT system. This paper describes the use of image analysis techniques including image segmentation, which uses a combination of thresholding and other methods to characterize and quantify crack and mineral dissemination in the sphalerite particles after comminution with the HPGR and Cone crusher. The results are validated with those obtained using traditional techniques such as physical gas (with N2) adsorption, mercury intrusion porosimetry, SEM and QEMSCAN.

Jan 1, 2012

By L. K. Mireku

"Abstract - The Halfmile Lake South Deep zone, Bathurst Mining Camp, New Brunswick, was discovered by Noranda Inc. (Exploration) as a result of a 3-D seismic survey in 1998 and the subsequent drilling of ten diamond-drill cores. The deposit consists of massive, breccia, and stockwork Pb-Zn-Cu sulfide minerals, and is hosted by a volcano-sedimentary sequence belonging to the overturned Ordovician Tetagouche Group. Epiclastic rocks and interbedded fine-grained felsic pyroclastic rocks dominate the stratigraphic footwall. Locally, crystal-rich felsic tuffs and subordinate epiclastic rocks comprise the immediate stratigraphic hanging wall. The entire stratigraphic sequence was intruded by quartz-feldspar porphyritic intrusions, and cut by intermediate and basic dikes. The volcanic and sedimentary rocks can be discriminated geochemically using trace element ratios such as Zr/TiO2 and Nb/TiO2, despite intensive alteration and cleavage development. These ratios indicate that four protolith volcanic compositions exist: rhyolite, dacite, andesite, and basalt. The aphyric and feldspar- and quartz-phyric volcanic rocks are dacitic and rhyolitic in composition; epiclastic rocks have trace element ratios consistent with dacitic compositions. Pearce element ratio diagrams, general element ratio diagrams, and petrographic observations demonstrate that the rhyolitic volcanic rocks exhibit evidence of albite, potassium feldspar, and quartz fractionation, dacitic volcanic rocks exhibit little evidence of any fractionation, and epiclastic sedimentary rocks exhibit evidence of quartz sorting only. Hydrothermal alteration is best represented by the presence of phengitic muscovite and daphnitic chlorite. Minor calcite occurs in the stratigraphic hanging wall, deep in the stratigraphic footwall, and in post-mineralization dikes, and thus is not interpreted to be part of the causative hydrothermal event. Element additions and losses during alteration have been used to determine net alteration reactions, and these have been used to identify alteration parameters that are independent of other forms of alteration and fractionation/sorting, and which can be used to guide exploration. These parameters include: a bulk hydrolysis measure, (2Ca+Na+K-2CO2)/Al; a muscovite alteration measure, K/Al; an albite destruction measure, Na/Al; a chlorite alteration measure, (Fe+Mg-S/2)/Al; a chlorite composition measure, (Fe-S/2)/Mg; a sulfidization measure, S/Ti; and a carbonatization measure, CO2/Ti. With the exception of the carbonatization measure, these alteration parameters define a distinct lateral and vertical zone of intense hydrothermal alteration in the stratigraphic footwall of the deposit, and demonstrate that the epiclastic rocks are predominantly chlorite altered, and the volcanic rocks are predominantly muscovite altered. Within the alteration halo, element additions of Fe and H, and element losses of Na are characteristic. Potassium was added to muscovite-altered rocks, but subsequently removed from chlorite-altered rocks. The results from this study demonstrate that metamorphism and deformation have not significantly obscured hydrothermal alteration signatures."

Jan 1, 2006

By Allan R. Punkkinen

Safe extraction of the valued ore resource in the deep levels of VALE Creighton Mine has progressed in a pillar-less fashion using vertical retreat, slot-slash and uppers retreat methods since the cessation of ?cut and fill? mining in the late 1980?s. Sequencing of the panel extraction and filling has been the key to successful exploitation of high stress orebodies at depth. In late 2010, discussions between the Operating Department and Creighton Ground Control revealed an opportunity to evaluate a trial primarysecondary sequence in the west end of the 400 Orebody at the 2340m horizon. To manage the trial primarysecondary project, a high level risk analysis and management of change was carried out to mitigate potential danger. As part of the requirements, an instrumentation project was conducted in the hanging wall and footwall bottomsills of the secondary panel and within the secondary panel itself. The extraction sequence was modeled with Map3D® software, confirming high stress levels with the advance of the primary panel. Enhanced ground support was installed based on modelling results. A key objective of the instrumentation project was to verify support system response to mining and to obtain knowledge in regards to the behavior of the stope. This paper describes the first time that this type of new innovative instrumented rockbolt technology had been used in a hard rock mining environment. Understanding of the physical deformation mechanisms of ground support in response to high stress conditions is the basis for an effective ground control strategy. The data played an important role in subsequent enhanced ground support system design at the mine and importantly, established the fact that the secondary pillar had not totally failed. Subsequent cavity monitor results helped establish that fact.

Jun 1, 2012

By F. Osmond, R. Kelly

"Malcolm Knowles, the famous adult educator once wrote: ""What a challenge we in human resources development face if we are to avoid the obsolescence of our workforce. I can foresee this challenge requiring that we reconceptualize (...) and redefine the role of HRD, away from that of managing the logistics of conducting training activities to that of managing a system of learning resources"".The context in which this was written surrounds the subject of adult education and the need for business and industry to change its approach to the treatment of adults as learners. In explaining what 'managing a system of learning resources' means, Knowles refers to line supervisors and managers as the most ubiquitous resources for day-in and day-out employee development. In many organizations training has been largely a staff rather than line responsibility. Even where trainers reported to line management, it was still seen as a staff function performed by a few specialists.This change referred to by Knowles places a much heavier responsibility on line supervisors and managers for the development of their personnel than has traditionally been the case. Managing that change - handing over the responsibility to the line organization - is the supreme challenge for the HRD function.Just why is this change necessary? Because too often, the learner does not effectively use on the job what he or she learned in the classroom. In fact, learners often discard new methods and revert to the older ways. The reason training does not stick is that the systems for training and work management are most often separate entities and while one may support the other, they need to be a single integrated system in order to ensure the transfer to the job effectiveness of training and some real value for the training dollars.Because much training can be wasted, steps have to be taken to ensure that it fulfills its intended purpose. The effective and continuing application of knowledge and skills that learners acquire can only be realized when line supervisors and managers are at the centre of the training system.This paper describes how such a systemis being developed at the Iron Ore Company of Canada (IOC) as a functional training program is introduced. The following text provides background information on the IOC - who they are and where they are located, a definition of functional training, an evaluation of the suitability of this approach for adults in industry, a description of how the program is being implemented at IOC and some observations that have been made as this change is experienced."

Jan 1, 1995

By T. A. Wheat

"The presently increasing world-wide interest in advanced ceramic materials is generally focussed on their exploitation in both structural and functional applications. With the opportunity to engineer microstructures and thereby closely control and tailor the final properties, there are many new applications being made for these materials in both areas.The scope and some of the applications for functional ceramics are reviewed and examples of the present Canadian activity in this field are discussed.BackgroundThere has been progressively increasing international interest in the development and exploitation of ceramic materials in the last five years. The stimulus for this interest arises from several quarters, each of which are independent of the other.• There is a growing awareness of the strategic nature and vulnerability of supply of the raw materials used to produce high performance metal alloys.• The metal alloys are reaching the upper temperature limit for their performance as structural components in engines.• The dramatic increase in oil prices during the late 1970s focussed attention on the need for reduced consumption in many sectors, i.e., there is a need for more efficient engines that operate at higher temperatures - above those tolerated by the present superalloys.• A number of ceramics, especially the structural materials such as SiC, A120 3, AI20rSi02, Si3N4 and the Sialons are produced using non-strategic raw materials and they can exhibit startling performance-auto turbo-rotors are in production mad e of Si3N4 that operate up to 190000 rpm at 600°C, 150000 rpm at 900°C.• Ceramic s are generally of lower density - significant in the weight-reduction of automobiles such as the replacement of a 20-kg five-segment steel leaf spring with a single segment carbon-fibre reinforced unit of 3 kg. • Ceramics also offer major ad vantages in generating, monitoring or controlling the electromagnetic spectrum whether in bulk or thin-film devices that exploit optical, magnetic, pyroelectric, piezoelectric, electronic and I or ionic conductivity characteristics.The opportunity to combine several of these char acteristics in a single material by composition, processing and microstructural design has resulted in an advanced ceramics industry that had world-wide sales in 1980of $4.2 billion (U.S.)(I) and is predicted to grow to sales in the range $7 to $10 billion by 1990 and $16 to $24 billion by the year 2000(2). However, at present, advanced ceramics account for less than 20010 of the total ceramic market."

Jan 1, 1987

By F. G. Smith

Abstract Laboratory methods are now in use whereby the temperature and pressure during the crystallization of hydrothermal minerals can be determined. The techniques include the use of the decrepitation method of studying liquid inclusions, and electrical measurements of pyrite. The determinations are sufficiently accurate that the data can be used in solving a variety of ore deposition problems. Within the last year, several new laboratory techniques have been developed in the Geochemical Laboratory of the Department of Geological Sciences, University of Toronto. The results of several tests of ore by these methods have proved to be useful in treating some problems which previously were considered unsolvable. It is now possible to determine the temperature of deposition of most of the minerals in a hydrothermal ore deposit, also the depth below the surface during deposition. Measurements can also be made of the reopening history of a complex ore. The temperature-pressure determinations depend upon the fact that minerals deposited from a hydrothermal solution always trap a small amount of the solution at the time of crystallization. The solution, being predominantly composed of water, has a density which depends upon the temperature and the pressure prevailing during crystallization. After ore deposition is complete, erosion and isostatic uplift finally exhumes the vein. During this slow fall in temperature and pressure, the solution contracts and a gas bubble appears. If the trapped solution in the mineral is examined, the gas-liquid ratio records the density of the solution at the time the mineral was deposited (except for a slight change in the volume of the mineral). The thermal expansion and compressibility of water and water solutions are known to a sufficient degree that, if the gas /liquid ratio can be determined, the temperature-pressure relations during deposition can be calculated.

Jan 1, 1949

By R. F. Favreau

"After a blast, the volume of the blasted rock normally occupies more space that it did before the explosion. The degree of such swell significantly affects the efficiency of digging the muck with a shovel or dragline. This paper explains why swell occurs, and describes the new subroutine SWELL of the blast simulator BLASP A which can simulate blast-induced swell. Results are also presented which display the effect of various blasting parameters on the degree and distribution of the swell within the muck pile of a bench blast. IntroductionIt is a common opinion that fragmentation is the most important of the various aspects which affect the efficiency of excavating rock with explosives. This paper proposes that, in fact, displacement and swell of the blasted rock are as important as fragmentation if the excavation process is to be rapid and efficient. It must ""a priori"" be recognized that a minimum degree of fragmentation is indeed necessary. For a given shovel or dragline, this minimum degree of fragmentation may be defined as follows: even the largest fragment of rock must be easily contained within the bucket. Once this criterion is met, however, there are good reasons to believe that displacement and swell take over as the key criteria which influence the rate of mucking, in cubic metres/hour. If the muck pile is not well displaced and swelled, the teeth of the bucket have difficulty penetrating between the rock fragments even if fragmentation is good and, as a result, the mucking is slow and inefficient. The purpose of this paper is to use computer simulations on the model BLASP A to demonstrate the effect of the blast design parameters on the displacement and swell of the blasted rock."

Jan 1, 1993

By Chris Blain

"Abstract - Based upon an extensive database, this paper analyzes the record of modern mineral exploration success and establishes the 50-year trends in discovery. The record clearly shows that the overall discovery rate rose during the 1950s and 1960s, peaked in the 1980s, and fell during the 1980s and 1990s. By commodity and ore-type target, the pattern of discovery is not continuous. Typically, it is episodic as a series of waves with minor resurgence. The waves reflect the order of the so-called discovery booms, led by uranium, then nickel, and copper, polymetallic base metals and gold. With the possible exception of gold, the discovery booms appear to be independent of metal price, although favorable perceptions of the price outlook may well have initiated the boom or led resurgence. Although difficult to quantify, an emerging trend in modern discovery is the integration of several detection techniques into the search process. No doubt, this trend will continue as orebodies become more and more difficult to find. The record of the past two decades shows that greenfield discovery rates have progressively fallen even though the level of investment in exploration has risen to an all-time high. This trend reflects increasing discovery risk. Several factors are contributing to this trend. Perhaps the two most important are: (1) deteriorating economics as increasing real costs and decreasing real prices continue to raise the economic hurdles for minimum acceptable exploration targets, and (2) increasing exploration maturity in many search terrains, particularly those in the traditional regions of North America and Australasia. To succeed cost-effectively in this new environment of increasing discovery risk will require extraordinary creativity, innovation, and technical skill coupled with commercial discipline."

Jan 1, 2000

By H. K. Taylor

"As a mining engineer with over 50 years' experience in underground operations and mine planning, I appreciate the enormous amount of work that went into the paper; and despite an imbalance between geology-geostatistics and the profit-earning actions of mining and treating (possibly because of sponsorship only by the Geological Society), I agree with probably 85% of the detail. But the paper fails to build on its own sound foundations and, like many predecessors, drifts instead into idealism. Even the starting quotation from the US SEC Form S-18 is little more than a platitude. An American consultant (l) has observed: ""an evaluation that accepts ore reserves as guaranteed because their definition meets SEC criteria is an invitation to disaster"".Idealism enshrines at least two myths that have bedevilled definition over the last several decades. The first is that the only purpose of 'ore reserves' is to promise successful new mines, and that 'ore reserves' must necessarily follow feasibility studies.In practice, the identification of what is likely to be mined if a mine is started must often be done on broad economics long before the feasibility study, and there may be only little later flexibility. The second myth is that there can be a perfect deposit with a simple exploration-appraisal-development sequence (the paper's Figure 2) against which all inferiors can be matched. If the field of definition be regarded as a pyramid, the quest for perfection and the imposition of rigid promises upon the terms 'ore' and 'reserves' drive definitions so near the apex (or the bottom right corner of Figure I, if preferred) that little is left to define. The process is reminiscent of the legendary super-medicine, the one so powerful that the patient had to be in perfect health to take it!"

Jan 1, 1992

By G. C. Weatherly, L Beitelman, M Gray, M. W. Bates, R Hadden

"A program of evaluation of in-mould electromagnetic stirring on the product of a straight-mould, billet continuous casting machine has been carried out. The effects on macrostructure, surface and internal quality, chemistry segregation and mechanical properties on carbon, low-alloy and resulphurized, free-machining steel billets and rolled bars are discussed. Operational aspects as a result of in-mould stirring are highlightedIntroductionA development program on electromagnetic stirring (EMS) in the mould of a continuous caster was started by Ferrco Engineering Limited in 1979, with the first experimental device being developed and installed at Lake Ontario Steel Company. As a result of these initial trials, new designs of in-mould EMS systems have been developed and are currently being used in continuous casters in North America and Europe. The rapid progress which has been made is in large measure due to the fruitful cooperation which has existed between the various parties, including Ferrco, the EMS equipment manufacturer, several operating plants and the University of Toronto.A brief review of some of the basic ' principles of electromagnetic stirring action on solidifying metal, and the landmarks of this process development, will explain the philosophy of this cooperation.From casting practice, it is well known that an equiaxed dendritic structure provides better' material properties than a columnar dendritic structure. Homogeneity of the equiaxed structure leads to better control of material properties, such as strength and ductility. Therefore, many efforts are being made to obtain this structure in continuous casting.The extent of the equiaxed zone is determined to a large degree by convective flow in the liquid. Fluid flow can fragment dendrites in the columnar zone, which then act as nuclei for grains in the equiaxed zone farther down the sump. This process is referred to as dendrite or grain multiplication."

Jan 1, 1982

By G. A. Kosick, M. Freberg, L. A. Kuehn

"Highly variable and higher than forecast lead miff feed grades were problems experienced at the Polaris Concentrator. Limited flotation capacity and poor operating flexibility prevented the plant operators from overcoming these difficulties, and resulted in grades and recoveries which were lower than necessary.Two column cells were integrated into the lead circuit in an effort to give the operators the tools they required to achieve the best grades and recoveries possible, regardless of the miff feed grade. Installation of the column cells increased lead concentrate grade from 76% to 79.3% Pb, and increased lead recovery from 9/% to 91.3% Pb.This paper reviews the design, development and operation of column flotation cells in the lead circuit at the Polaris Mine.IntroductionThe Polaris Concentrator was constructed in 1980 on a barge in Trois Rivieres, Quebec, and towed to its pre sent location on Little Cornwallis Island, Northwest Territories, about 1450 km from the North Pole. The plant presently treat s about 2800 mtpd of new feed with average feed grades of 3010 Pb, 13% Zn and 5% Fe. Current production averages 36 000 tonnes of lead concentrate and 220 000 tonnes of zinc concentrate annually.The barge design and min e location dictated that the concentrator .be compact with very little unused floor space. As a result, flexibility was limited in terms of expanding the plant.Mill feed grades were highly variable and above forecast and the lead flotation circuit was found to be under capacity. This caused continued overloads in the lead cleaning circuit, resulting in low concentrate grades and recoveries. It was evident that an increase in lead flotation capacity and flexibility was necessary. The existing floor space did not allow for the installation of additional conventional flotation cells, but one alternative was the installation of column cells."

Jan 1, 1988

By Minoru Fujita, Ian M. Johnson

"A helicopter-borne geophysical survey was flown in 1978 over selected areas on Kyushu Island, Japan. The principal sensors were a moving source electro-magnetic system and a magnetometer. Maps of apparent resistivity were generated from the EM data. Based on the resistivity signature of known deposits within the survey areas, targets were selected for ground follow-up. Drilling of one such target in late 1980 resulted in the discovery of a gold deposit from which full production will begin in the summer of 1985. The deposit contains a minimum 120 tonnes (3.86 million ounces) of recoverable gold and is the largest in Japanese history. The deposit is in a geological setting previously unsuspected of hosting precious metal deposits. The case history suggests a preferred exploration strategy which might be employed in other similar geological environments.IntroductionThe Hishikari area is located some forty-five kilometres north of Kagoshima city, Kagoshima Prefecture, Kyushu Island, Japan (Fig. I). The area and its environs is one with a number of gold deposits which have been worked with varying results since the late 1800s. The large st deposit in terms of recovered gold is the Ohkuchi (or Oguchi) Mine (Fig . 2) which was recently closed due to exhaustion of reserves. The Ohkuchi Mine started production in 1896. A total of 22.2 tonnes (714 ,000 ounces) of gold, with an average ore grade of 13.6 grams/tonne (0.39 ounces/ton), was extracted over the Life of the mine.In an attempt to discover new deposits , the Metal Mining Agency of Japan (MMAJ) carried out a regional geologic mapping program of the area between 1975 and 1977. This was followed by a helicopter-borne electromagnetic and magnetic survey. The airborne survey was flown by Scintrex and the compiled results presented to MMAJ in early 1979."

Jan 1, 1985

By G. J. Kipouros, P. W. Kingston, W. F. Caley

"Current practice in advanced materials processing has involved the dispersion of a second-phase, commonly SiC, glass, or other non-metallic fibres/whiskers/particulates to enhance physical characteristics of the matrix. These matrices may be either ceramic or metallic but in either case it is important that the physical and chemical properties of each phase be compatible. The dispersed, finely divided second phase is often both expensive and foreign-produced and may exhibit chemical instability at elevated temperatures. Thus, it would appear that certain naturally-occurring industrial mineral fibres/whiskers/particulates might offer an attractive and low-cost alternative. Suitable candidates, such as wollastonite and sillimanite, are available in Canada and may be milled to produce particles whose shape is appropriate for this application. It is suggested that wollastonite, in particular, may be a useful modifying agent in metal matrix composites utilizing AI, Al-Si, Zn-Al or other light metals and alloys. In addition, the possible use of these minerals in ceramic matrix materials is also addressed, with reference to a preliminary thermodynamic analysis of the systems involved.IntroductionBackgroundA composite material may be thought of as consisting of a matrix component, the properties of which are improved by the addition of a second component or dispersed phase which forms a distinct three-dimensional interface with the matrix. This matrix is commonly either metallic or ceramic, which leads to the two most popular types of composites: metal-matrix composites (MMC); and ceramic-matrix composites (CMC).Such materials are by no means new. Early composites include fiberglass, mixtures of plaster and horsehair in wall plastering, as well as use of natural materials such as bamboo in fishing rods. Some of the newer applications include high strength, low-weight bicycle rims, as well as the more familiar role in aircraft and automobile engine components."

Jan 1, 1993