Search Documents

By Sammy Bansah, Komla Dzigbodi-Adjimah

Abstract-Ghana, a major West African gold-producing country, took a crucial step in 1986 to allow private participation in mining ventures that had hitherto been state controlled and starved of funds. This decision has led to a three-fold rise in gold production with substantial local and foreign capital once again flowing into exploration and mining projects. Though the rise in gold export is due primarily to increased production from large mines such as Ashanti Goldfields Corporation, Billiton Bogosu Gold, Tebrebie Goldfields and Ghana Australia Gold that work primary lode gold deposits on quartz veins and Banket conglomerates, a fair amount of gold comes from placer gold mining from which two new mines have been developed at Kwabeng and Bonte during the current gold boom. Also, placer gold mining is important locally because the lower capital outlay required for its development enables many entrepreneurs to operate small concessions and provide employment for a large pool of unskilled labor. Placer gold exploration and development in Ghana is labor-intensive. Pitting is the most used method although few employ the mechanized ("Banka") drilling. The advantages and disadvantages of the two approaches in the local setting are discussed. The gravel is normally sluiced and the gold recovered by amalgamation. The drawbacks to successful placer gold exploration in Ghana have been attributed to lapses in execution of exploration programs (Dzigbodi- Adjimah and Arhin, 1993; Dzigbodi-Adjimah and Gawu, 1994). However, the failure to recognize and set time frameworks and financial limitations for the various stages of placer gold exploration have spelt the doom of some projects. It is critical that the characteristics of the placer gold deposit be determined by efficient and cost effective means. A planned exploration supported by adequate flow of funds saves costs and leads to success. This article discusses the current Ghanaian situation and presents proposals from case studies for planning and budgeting placer gold exploration programs for use in similar settings.

Jan 1, 1995

By Sammy Bansah, Komla Dzigbodi-Adjimah

Ghana, a major West African gold-producing country, took a crucial step in 1986 to allow private participation in mining ventures that had hitherto been state controlled and starved of funds. This decision has led to a three-fold rise in gold production with substantial local and foreign capital once again flowing into exploration and mining projects. Though the rise in gold export is due primarily to increased production from large mines such as Ashanti Goldfields Corporation, Billiton Bogosu Gold, Tebrebie Goldfields and Ghana Australia Gold that work primary lode gold deposits on quartz veins and Banket conglomerates, a fair amount of gold comes from placer gold mining from which two new mines have been developed at Kwabeng and Bonte during the current gold boom. Also, placer gold mining is important locally because the lower capital outlay required for its development enables many entrepreneurs to operate small concessions and provide employment for a large pool of unskilled labor. Placer gold exploration and development in Ghana is labor-intensive. Pitting is the most used method although few employ the mechanized (“Banka”) drilling. The advantages and disadvantages of the two approaches in the local setting are discussed. The gravel is normally sluiced and the gold recovered by amalgamation. The drawbacks to successful placer gold exploration in Ghana have been attributed to lapses in execution of exploration programs (Dzigbodi-Adjimah and Arhin, 1993; Dzigbodi-Adjimah and Gawu, 1994). However, the failure to recognize and set time frameworks and financial limitations for the various stages of placer gold exploration have spelt the doom of some projects. It is critical that the characteristics of the placer gold deposit be determined by efficient and cost effective means. A planned exploration supported by adequate flow of funds saves costs and leads to success. This article discusses the current Ghanaian situation and presents proposals from case studies for planning and budgeting placer gold exploration pro-grams for use in similar settings.

Jan 1, 1995

By Tatyana Alexandrova

The problem of processing refractory (rebellious) gold ores is important for all the countries involved in recovering precious metals from ores. Technological aspects of processing precious metal ores are examined in two respects: enhancing gold recovery from double refractory ores; and using carbonaceous ores on a production scale. The dispersed carbonaceous matter (DCM) present in concentrates causes the adsorption of [Au(CN)2]- complex on their surface during cyanidation process. Depending on the degree of graphitization and the organic carbon content in DCM (including kerogens and bitumen), the technology used to recover precious metals varies considerably. The problem of processing refractory (rebellious) gold ores is important for all the countries involved in recovering precious metals from ores. Depending on the degree of graphitization and the organic carbon content in DCM (including kerogens and bitumen), the technology used to recover precious metals varies considerably. The possibility of rare metals recovery, including rhenium, from black-shale rocks, has been examined. Comparative assessment of analytical methods of rare metals detecting has been carried out. It has been proved that neutron activation analysis is a promising technique. It has been shown that colloid-salt fraction (nanofraction) with particle size less than 1000 nm makes up to 3 wt% of black shale samples and is extracted by water under special conditions. The use of water instead of chemically active reagents provides insolubility of the mineral matrix and fully reflects the colloid-salt element of the samples. To sum up, the justification of the choice of technology for processing of carbon-bearing ores is based on examining the type of carbonaceous matter and its adsorption behavior. When the content of carbon of high degree of metamorphism is considerable, it is possible to recover platinum group elements and rare elements from this type of ores. The obtained results predetermine the general guidelines for creating new methods and techniques of processing carbonaceous material for integral development of solid minerals in the mining and oilfield areas of Russia.

Jan 1, 2016

By Michael Farley, Paul Dufour

"Relationships, Partnerships,Marriages (RPM)RPM has a nice musical ring to it, but it is in fact synonymous with science and technology, university-government -corporate links and the more genera l issue of university roles in technology development. Pick up any report on one of these issues, and chances are that you will find one of these key words in the title. Play it, and you will find that the revolutions per minute are increasing. It is difficult to keep track of the wide variety of institutional experiments now developing in Canadian universities in attempts to marry science and research with technology commercialization and technology transfer.Why is the role of Canadian universities in this matter important? There are at least five good reasons:1. It is important because these knowledge institutions are producer s of scientific research, a major component of technology. Today the gap between the two is rapidly shrinking.2. It ' is important because Canadian industry is turning to universities for tech no logy development and new knowledge. Figure 1 shows that universities are becoming an important source of technology available to Canadian firm s; more important in fact than government. Figure 2 illustrates this trend more graphically in showing that university collaboration is one of the preferred methods of industry participating in co-operative R&D efforts:3. The role of Canadian universities in technology development is also important because the provincial and federal governments have embarked on various programs and policies for promoting the use of technology and science for economic benefit. Universities are playing an increasing role here. For example, the submission of IDEA Corporation (a venture capital operation funded by the government) in Ontario to the Bovey Commission on the Future Development of Ontario Universities clearly spelled out its ideas for commercialization of university research in Ontario . Among other things, the brief suggested that Ontario's universities need to be better equipped to transfer technology, and the reward structure in university research must incorporate industrial interests."

Jan 1, 1986

"The Pierre Beauchemin Mine attained commercial production in January 1989, and went on to produce 23 968 ounces of gold for the year, 3% higher than forecast. Underground development was accelerated to prepare the way for the production of an estimated 40 000 ounces in 1989.IntroductionThe Pierre Beauchemin Mine is located nine miles west of the city of Rouyn-Noranda (Fig. I).As a result of the amalgamation with Sullivan Mines in October 1987, the mine is now entirely owned by Cambior Inc.The Eldrich deposit was discovered in 1953and began production in 1955, closing in 1962 following the decrease in gold prices and the simultaneous decrease in silica content in the ore, which was sold to the Noranda smelter for flux. A total of 717 000 tons grading 0.14 oz Au/t were produced during this period.From July 1984 to October 1987, an underground exploration program was carried out by Sullivan on the Eldrich mining concession and the nearby Flavel property. The first phase of the program included reinstallation of surface facilities and dewatering of the Eldrich Mine. Following the completion of the first phase, extensive exploration was carried out, including a major program of diamond drilling. It was then decided to deepen the shaft to a depth of 1800 ft to access a new zone called the No.5 Zone .Following the amalgamation with Sullivan in October 1987, Cambior assumed the role of operator for the project, and continued the shaft deepening work that had already been started. A feasibility study was completed in April 1988 and the Cambior board of directors approved a production decision for the Eldrich-Flavel project.The preproduction program extended from May to December 1988 and was aimed at preparing the stopes in the upper part of the mine and at developing the mine infrastructure at the bottom of the mine.The mine was officially opened in August 1988. Cambior renamed the project the Pierre Beauchemin Mine in recognition of Pierre Beauchemin's pioneer-work."

Jan 1, 1990

By I. R. Muirhead

"One approach to making new technology available is to demonstrate its value under full-scale operating conditions. Studies were undertaken to assess the feasibility of this approach to introducing a longwall mining system to the western Canadian coalfields.The longwall method of mining coal is described, world and Canadian usage is reviewed, and the merits of the system in comparison 10 other coal mining methods are discussed.The rationale for a longwall demonstration in western Canada is presented, along with a proposed organization for the design, operation and dissemination of the findings from such a trial. The factors which must be considered in the design of the demonstration, and in the assessment of a potential site are highlighted. It is concluded that a demonstration of this technology is both timely and essential to prepare the way for the western Canadian coal industry of future prospects for coal.IntroductionFor many years CANMET has encouraged research work organized on a cooperative basis. This requires that a working consensus must be negotiated by researchers and operators at the beginning of the project and continuously refined as work proceeds. The result is usually a more relevant selection of research problems, improved direct ion and con duct of experiment al work and often a validation phase in which research concepts are tested in an opera ting environment. All this tends to narrow the gap between obtaining research results and applying them.Even under the best of circumstances cooperative projects require a good deal of coordination and enthusiasm to maintain focus and the pace of work. The working perspective of a research scientist in a government laboratory is substantially different from that of a mine operator at a producing mine, and a common ground must be found. This is difficult to do and cooperative projects typically evolve over several years as experimental results progressively define the potential solutions to mining problems."

Jan 1, 1985

By J. T. Birkholzer, M. Rutenberg, K. -H. Lux, R. Wolters, J. Rutqvist, L. Blanco Martin

In this paper, we present numerical results corresponding to the Thermal Simulation for Drift Emplacement (TSDE) test, conducted in the Asse salt mine (Germany) between 1990 and 1999 to simulate reference repository conditions for spent nuclear fuel in rock salt. This test is of significant relevance for nuclear waste disposal in salt because extensive research and measurement programs were set up for the experiment. In our numerical study, we use two sequential simulators, TOUGH-FLAC and FLAC-TOUGH, and we investigate two-way coupled processes, focusing on thermo-mechanical analyses due to the main effect of heating. The two simulators used have recently been updated and are able to deal with large strains and creep processes. Moreover, specific constitutive relationships and coupling functions for rock salt and crushed salt under repository conditions are available. Within the framework of a benchmark exercise between Lawrence Berkeley National Laboratory and Clausthal University of Technology, the same scenario has been modeled in three dimensions using the two simulators mentioned. The main objective of the current, first stage of the benchmark is to evaluate the capabilities of these two simulators to predict relevant processes under repository conditions for high-level nuclear waste in saliniferous media. The comparison of the numerical predictions between them is very satisfactory, leading to a successful code-to-code verification. The comparison between measurements and numerical results shows that the most important processes are captured by the codes and constitutive models used. However, some differences exist between measurements and numerical results. These differences will be addressed in the next stage of the benchmark exercise, in which a parameter fitting effort will be undertaken. Overall, from the results obtained it can be concluded that TOUGH-FLAC and FLAC-TOUGH have the necessary capabilities to reproduce relevant processes under repository conditions for high-level nuclear waste in saliniferous formations.

Jan 1, 2015

By Bruce Chalmers

INTRODUCTION TIE most important practical problem with which Physical Metallurgy is faced is the control of the mechanical properties of alloys. The most difficult aspect of this problem is the development of new alloys with the properties that are required for meeting exacting engineering requirements. A great measure of success has been achieved by following the empirical method and most, if not all, of the present variety of alloys have been developed by the process of experiment and observation or trial and error. It may, however, be that this method will become. less productive as time goes on, and that eventually it should be replaced by a process based on an understanding of the factors that determine the properties, so that alloys can be 'designed' to meet the requirements. This method of investigation will not be possible until a much better fundamental understanding of metals has been gained, and this will come only about as a result of a great deal of detailed research. The subject of Physical Metallurgy can be divided, as follows, into two parts: we may consider the factors which determine the structure, in the broadest sense, of an alloy. These include the composition and also the treatment to which the material has been subjected. The second aspect is the influence of the structure on the mechanical and other properties. In order to make an effective contribution in this field, it is necessary for an individual or a group to concentrate on a specific and very restricted topic. It is proposed to discuss in some detail the particular subject in which the writer and his colleagues are working.

Jan 1, 1951

By Guadalupe Sanchez, Roel Cruz, Sergio Castro, Claudia Beltrán, Isabel Lázaro

The recovery of zinc in refineries is strongly affected by the formation of zinc ferrites during the roasting of zinc concentrates. To achieve the highest zinc recovery most of these plants operate under high acidity and high temperature conditions in their leaching circuits. However, under these conditions high iron dissolution occurs. For iron control the common practice is to precipitate it as jarosite, and calcine is normally used as neutralizing agent. This practice causes a significant loss of metal values associated with the calcine, such as zinc ferrites and silver insoluble phases. These metal values are carried by the jarosite into confined waste in many plants. In order to diminish such losses, it is necessary to use a neutralizing agent that could substitute the use of calcine. An alternative neutralizing could be the basic zinc sulfate (BZnS). This work presents the results of a laboratory analysis on the required conditions for the BZnS production from process streams of a zinc refinery plant. Neutralizing behavior of BZnS was evaluated in iron precipitation as jarosite, in order to establish the feasibility of replacing the calcine and decrease the loss of zinc and other metals values during the iron removing step of the hydrometallurgical circuit of the zinc refinery under study.

Jan 1, 2014

By M. Kuyumcu

With annual production of almost 3.5 million metric tonnes of K20, former East Germany (GDR) was the world?s third-largest producer of potash, ranking behind only the Soviet Union and Canada. More than 80 % of production was intended for export to earn urgently needed hard currency. For this reason, beginning in the 1970s, East Germany began to mine unprofitable hard-salt sources and carnallitite fields, which are geomechanically problematic. In the course of restructuring from a centrally planned to a market economy after German reunification, only two of the nine existing potash mines were classified as economically viable for privatization. All six potash mines in the South Harz Region were closed between 1991 and 1993. The orderly safekeeping of these potash and other decommissioned ore mines and the rededication of mining areas were assigned in 1992 to a German state-owned company GVV founded especially for this purpose. Elaboration in the present documentation covers the local necessity of the type and extent of filling and safeguarding measures. As a result of the remedial measures taken, it was possible to prevent the collapse of cavities and damage to surface facilities. This documentation describes the safeguarding successes to date, with appreciable reduction and stabilization of surface settlement and with significant lessening of seismic events. Also presented are concepts updated to the state of the art for safeguarding of numerous potash mining shafts for long-term effectiveness in separation of the workings and watercourse levels in the cap rock. In the course of 100 years of production, six mining dumps resulted with a total volume of approximately 170 million m3. They consist of up to 95 % of water-soluble salts. Every year, precipitation dissolves up to 500,000 tonnes of this salt, which enters as a highly concentrated solution into watercourses and ground water. Explanation follows of measures for minimization of environmental pollution by covering of dumps and controlled drainage of alkaline solutions from the dumps. Finally, presentation is made of the results of the successful work until now by GVV for reuse of decommissioned mining sites with settlement of new companies for creation of additional jobs and for revitalization of the monostructured South Harz Potash Mining Region.

Aug 1, 2013

By J. Gillies

"Those of you who were at last years C.M.P. meeting are aware there was discussion at that meeting concerning the best method of assisting the assayers of metal mines to exchange new ideas and methods of assaying. The opportunity to advise you of what came of that discussion is very much appreciated.There are several societies, including the Chemical Institute of Canada, the Spectroscopy Society and others that could be of some assistance to assayers. However, since these societies cover a rather broad field and not many mine assayers have the opportunity to attend their meetings, it was felt that an organization oriented to the specific needs of the mine assayers would be of more value to them.Several years ago an attempt was made to hold meetings for the benefit of assayers in conjunction with the Conference of Metallurgists held each year by the Metallurgical Society of the C .I.M.M. This did not work because very few of the mine assayers attended the meetings.With the very evident success of the type of meetings the C.M.P. have and the excellent groundwork done by your secretary, Mr. Stevens, in talking about this to mine management and assayers at many mines across the country, it was decided to hold a meeting at Noranda on October 8 to discuss how best we could help ourselves solve our problems.For the initial meeting it was felt that perhaps it would be better to start with a smaller group, so invitations were sent to mines in Ontario and Quebec that were geographically fairly close to Noranda."

Jan 1, 1970

By G. A. Barclay

"I - INTRODUCTIONSteel castings still comprise the largest volume of wear materials used in crushing and grinding in the Canadian mining industry. The range of impact and wear properties possible with steel castings enables them to be used successfully in both high impact crushing as well as milling where abrasion resistance is the main criterion. Approximately 15,000 tons per year of steel mill liners and crusher castings are used by Canadian mines.The properties of the main steel casting alloys used - manganese, pearlitic chrome-moly and martensitic medium carbon steels will be discussed with reference to their applications. Field data on a new application in primary gyratory crushers for martensitic medium carbon steels is presented. Liner wear life and mill efficiency can be improved through proper liner design.The liner wear pattern can be used as an indication for liner profile changes to improve wear life. Changes in liner configuration can improve through put and use of larger castings can reduce downtime. Casting performance can be improved and foundry production costs reduced by adopting certain design improvements.II - ALLOYS USEDTable I list the most common ferrous liner materials used in relation to their hardness and wear resistance (1). The most wear resistant materials are the irons at the top. In many applications the service impact exceeds the impact strength of the irons and tougher less wear resistant steels must be used. The impact resistance improves from top to bottom with manganese steel the toughest. The hardness of the martensitic steels approaches that of the Ni-Hards however the wear life, because of the absence of carbides, is less."

Jan 1, 1983

By D. Pearcey, S. T. Vessey, V. Hegde, J. Staples

"Pellet quality has taken on a new dimension during the last ten years. Quality in the seventies was generally defined as adherence to certain physical and chemical specifications. Today, the talk is in terms of how the business is managed, how customer's expectations can be exceeded, not only in product quality, but in service responsiveness.Coke breeze and flux additions, lower silica levels, and improved furnace control practices have all contributed to the improvement of pellet physical and metallurgical properties. Statistical process control has provided additional insight into the parameters that affect pellet quality.Increased customer contact and product quality surveys have heightened our awareness of customer needs and also provide direction for quality improvement test work. Current work is focussed on improving reducibility and understanding the relationship between tumble, fired compression and metallurgical properties.This paper will review the Iron Ore Company of Canada's efforts during the past decade and describe some of its initiatives for the future.IntroductionThe Carol Pellet PlantThe Iron Ore Company of Canada's Carol Project is located in Labrador City in the southwestern portion of Newfoundland and Labrador , approximately 965 Ian northeast of Montreal. The project consists of mining facilities, beneficiation complex and a pellet plant, which began operations in 1962. The pellet plant consists of six Dravo-Lurgi straight grate machines, regrinding, filtering and balling facilities. The current capacity of the Carol pellet plant is approximately 10.5 million tonnes , while the concentrator has the capacity to produce about 18 million tonnes of concentrate.The orebody consists of specular hematite, magnetite and small quantities of limonite and goethite. The average grade of the orebody is approximately 39% iron."

Jan 1, 1991

By Xianglin Yang, Hong Zhong, Jingjing Xiao, Guangyi Liu

"The selective adsorption of a flotation collector to a mineral plays a crucial role in enhancing the hydrophobicity of targeted mineral particles for attaching air bubbles in pulp. The recent progress of the structure-reactivity relationship of flotation collectors, the characterization methods for mineral surfaces with adsorbed collectors and their commercial application are reviewed in this paper. Particular emphasis is placed on the density functional theory (DFT) for understanding the reactivity of new collectors, the surface analysis techniques including time-of-flight secondary ion mass spectrometry (ToF-SIMS), in situ scanning electrochemical microscopy (SECM) and atomic force microscope (AFM) to characterize mineral/collector interface, and the flotation technologies for optimizing recovery of valuable minerals. Especially, the recently developing collectors such as Gemini, alkoxyalkylthiourea, dithiourea, amide-hydroxamate and oximido-thiol surfactants, and their specificity to given minerals are evaluated. Based on this crucial review, it is evident that the structural modification approaches for minerophilic or hydrophobic groups, and combined surface analysis approach for further understanding the adsorption mechanism of collectors on mineral surfaces will lay a solid foundation for the future development of flotation collectors. INTRODUCTIONIn mineral processing, flotation is the main process for separation and recovery of valuable minerals from the ores contained them (Fuerstenau et al., 2007). One of the key requirements in flotation process is to increase selectively the surface hydrophobicity of the targeted minerals by collector adsorption so that these mineral particles can preferably attach to air bubbles in a slurry or pulp (Fuerstenau et al., 2007). Flotation collector is a kind of functional surfactant, which is composed of polar and non-polar groups (Somasundaran, & Wang, 2006). Non-polar portion, commonly being linear, branch or ring hydrocarbon group, is termed hydrophobic group. The polar portion, exhibiting strong affinity to mineral surfaces, is known as minerophilic group (Nagaraj, 1988). According to mineral types including saline, oxide and sulfide minerals, flotation collector divides into sulfide and oxide mineral collectors. For efficient recovery of valuable minerals from the refractory complex ores, insights into the adsorption mechanism, hydrophobic model and subsequent flotation approach of flotation collectors have been regarded as an indispensable issue in mineral processing."

Jan 1, 2016

By J. R. Meyer, P. L. Dean

"The Department of Mines and Energy is at present investigating the dimension-stone potential of the Nain anorthosite complex. These rocks are known to host occurrences of labradorite, a semiprecious gemstone known for its beautiful play of colours (chatoyance). Test blocks that contain 5% to 18% chatoyant labradorite were extracted from three prospects south of Nain. These have been slabbed and polished for further evaluation.Second-grade labradorite stockpiled around the Grenfell quarry on Tabor Island is also being evaluated as a potential source of aggregate for use in terrazzo tiles, precast concrete and epoxy-backed wall panels.IntroductionThe Nain anorthosite complex consists of approximately 10000 km2 of anorthosite and related basic rocks , which are well exposed along the coast of Northern Labrador (Fig. 1) (Emslie et al., 1972). These rocks have been known for centuries to host deposits of gem-quality labradorite. The chatoyant nature (i.e. the play of colours or labradorescence) of this semiprecious feldspar has been utilized mostly in the making of jewelry and other polished, handcrafted products. In the early sixties, Brinex Limited (now Brinco Limited) attempted larger scale commercial exploitation of labradorite, including use 'as building stone and in polished precast concrete for facings on buildings' (Brummer, 1984). After six years of work, which included market studies, Brinex decided that, at that time, the demand did not warrant further production.In recent years, there has been a dramatic increase in the markets for dimension-stone. In the period from 1980 to 1985, the demand in the United States for granite, much of which is imported, has increased 1735070 (Marble Institute of America, 1986). The dimension-stone industry's remarkable growth rate has, in part, resulted from new technology that makes it easier and faster to quarry and cut stone. This has allowed natural storie to compete with other building materials. Now, it is not only used for exterior cladding and walkways, but also on interior walls and floors, and in home and office furnishings, such as countertops for kitchens and bathrooms, table and desk tops, stairways, window sills, and fireplaces."

Jan 1, 1988

By J. R. Meyer, P. L. Dean

"The Department of Mines and Energy is at present investigating the dimension-stone potential of the Nain anorthosite complex. These rocks are known to host occurrences of labradorite, a semiprecious gemstone known for its beautiful play of colours (chatoyance). Test blocks that contain 5% to 18% chatoyant labradorite were extracted from three prospects south of Nain. These have been slabbed and polished for further evaluation.Second-grade labradorite stockpiled around the Grenfell quarry on Tabor Island is also being evaluated as a potential source of aggregate for use in terrazzo tiles, precast concrete and epoxy-backed wall panels.IntroductionThe Nain anorthosite complex consists of approximately 10000 km2 of anorthosite and related basic rocks , which are well exposed along the coast of Northern Labrador (Fig. 1) (Emslie et al., 1972). These rocks have been known for centuries to host deposits of gem-quality labradorite. The chatoyant nature (i.e. the play of colours or labradorescence) of this semiprecious feldspar has been utilized mostly in the making of jewelry and other polished, handcrafted products. In the early sixties, Brinex Limited (now Brinco Limited) attempted larger scale commercial exploitation of labradorite, including use 'as building stone and in polished precast concrete for facings on buildings' (Brummer, 1984). After six years of work, which included market studies, Brinex decided that, at that time, the demand did not warrant further production.In recent years, there has been a dramatic increase in the markets for dimension-stone. In the period from 1980 to 1985, the demand in the United States for granite, much of which is imported, has increased 1735070 (Marble Institute of America, 1986). The dimension-stone industry's remarkable growth rate has, in part, resulted from new technology that makes it easier and faster to quarry and cut stone. This has allowed natural storie to compete with other building materials. Now, it is not only used for exterior cladding and walkways, but also on interior walls and floors, and in home and office furnishings, such as countertops for kitchens and bathrooms, table and desk tops, stairways, window sills, and fireplaces."

Jan 1, 1988

By Peter S. Jack

"IntroductionTHE ORES treated at the concentrator of the Britannia Mining and Smelting Company, Limited, Britannia Beach, B.C., have always contained some lead, but it was not until 1950 that the combination of lead headings and lead price was such that recovery of this metal at Britannia became worthwhile. In that year, with the mining of a new orebody, the lead in the mill feed was raised from 0.07 per cent to 0.15 per cent. Chalcopyrite, sphalerite, and pyrite concentrates are produced by flotation at Britannia, •and 95 per cent of the lead in the mill feed reports with the chalcopyrite concentrate, so that the rise in lead headings was reflected almost wholly in the lead content of the copper concentrate. In 1950, investigation was started to determine if some of this lead could be recovered economically."

Jan 1, 1953

By X. F. Liu, O. Buzzi, Y. Sieffert

This study falls in the context of underground coal fires (UCF) where burning coal can elevate the temperature of a rock mass in excess of thousand degrees. The objective of the research was to experimentally investigate the change in mechanical behavior of a rock when subjected to temperatures up to 900 °C. Several blocks of an Australian mudstone were collected from a mining site in New South Wales, Australia. X-ray diffraction and thermal-gravimetric analysis were conducted on powdered rock in order to determine the critical temperatures at which the main mineralogical changes occur. Then, cylindrical specimens were prepared from intact rock blocks for unconfined compression tests. These rock specimens were then treated by heating in a temperature-controlled furnace at temperatures varying from 100 °C to 900 °C. The heating process consisted of two stages: raising temperature with very slow rate of 1 °C per hour followed by a holding period of 24 hours and then a slow cooling process to room temperature. The compression tests were carried out on treated rock specimens to characterize the change in compressive strength. The macroscopical study was complemented by microstructural investigations via optical microscope, scanning electron microscope (SEM) and mercury intrusion porosimetry (MIP). Results show that the unconfined compressive strength of mudstone decreases with increasing heating temperature up to 450 °C, beyond which it increases. This can be explained by the combined effects of micro cracks and mineral thermal reactions caused by heating process.

Jan 1, 2015

By D. L. Cramp

The Direct-Connected Electric Hoist In the latter part of 1931 a new electric hoist was installed at the Lake Shore mine. A number of interesting features were incorporated in this machine, which is the first direct-connected, direct-current-operated hoist to be placed in service in the Kirkland Lake district. Many factors requiring care and study enter into the selection of hoisting-engine drive. In this instance, conditions warranted the selection of the generator voltage control system (Ward-Leonard), utilizing a direct-current driving motor and a separate motor generator unit. It was further deter-mined that additional economies could be secured by the selection of a motor generator unit with a flywheel, and consequently the Ilgner-Ward Leonard flywheel set was adopted. Some of the advantages of this system are: 1) Greater accuracy of control, resulting in increased flexibility in hand-ling with increased precision and safety; especially desirable in large, important installations where the rope-speed is high or where frequent shifting is necessary. (2) Reduced energy consumption. (3) Feasibility of load equalization, without which, in some cases, the power system would be unable to carry the fluctuating load imposed on it by the operation of the hoist. ( 4) Elimination of reduction gearing in the construction of the hoist. The hoist is located on the surface and is used for skip operation at the main shaft, hoisting ore from a present maximum depth of 4,200 feet.

Jan 1, 1933

By K. C. Sole

In most copper solvent-extraction operations, an important consideration in choice of extractant is the requirement for high selectivity of copper over iron. Ester-modified aldoxime extractants presently offer the best Cu:Fe selectivity. In some plants, however, the process feed liquors contain significant amounts of manganese but little iron. Although manganese is not chemically extracted by oximes, trace amounts are carried over to the electrowinning circuit by physical entrainment. This may result in anodic oxidation of manganese which, in turn, can cause oxidative degradation of the organic phase when returned to the solvent-extraction circuit in the spent electrolyte. Many of these operations prefer to operate with higher levels of iron reporting to the advance electrolyte, as appropriate control of the Fe(II)/Fe(III) couple will ensure that manganese remains in the benign Mn(II) form. A new reagent, LS 4202, designed by Cytec, now offers the possibility of tailoring the iron co-extraction, so that appropriate Cu:Fe selectivity can be achieved in the solvent-extraction operation to maintain an electrolyte Fe:Mn mass ratio of >10:1, while retaining the other benefits offered by ester-modified aldoximes. The results of an integrated solvent extraction-electrowinning pilot-plant trial are presented, in which the performances of the conventional extractants ACORGA® M.5774 and LIX® 984N are compared with LS 4202. The Cu:Fe selectivity is demonstrated, along with results on the transfer of other impurities to the advance electrolyte.

Jan 1, 2007