Search Documents

By Yosuke Ota, Makoto Tawara, Tetsuya Kojima

"Dry-lube has been used in Europe to enhance formability of aluminum sheet for automotive applications, but it is difficult to ensure degreasing performance with lower degreasing bath temperature. However, newly developed, highly lubricating pre-coats utilizing a urethane resin, which is soluble in water, have been found to show excellent degreasing performance. Furthermore, a richer pre-coat weight coincides with a lower friction coefficient and better formability. Combined use of anti-rust liquid oil showed different friction coefficient depending on applied surface pressure.INTRODUCTION The global demand for aluminum alloy products, especially for automotive application, has been increasing because aluminum alloys can offer excellent corrosion resistance with good strength and low density compared with steel. Aluminum alloys can contribute to saving much more energy and greenhouse gas emissions over the lifetime of the product. On the other hand, the amount of aluminum alloys in vehicle architectures is still somewhat limited due to relatively low formability. As a consequence of this low formability, it is necessary to set a certain limit to the shape of an aluminum alloy panel for automotive applications. So far hot melt wax dry lubricants have been in use especially in Europe as they have been recognized to provide better lubrication than conventional rust protection oils (Meiler & Jaschke, 2005). The benefit of hot-melt wax for automotive manufacturing is associated with a more stable forming process and the possibility to avoid extra lubrication in the press shop. But because of the low poorer solubility of hot-melt wax in degreasing aqueous bath solution, a higher degreasing temperature is required so that no remnant of hot melt wax can be carried over to the next manufacturing process. This temperature control is difficult to impress upon a manufacturing degreasing bath originally designed for liquid oil, especially in Japan. The typical temperature of degreasing bath in Europe is around 60°C, while it is only around 40°C. in Japan. Various types of pre-coats other than hot-melt with high lubricity have been reported (Tawara, 1993; Ueda, Hatsuno & Totani, 2013), but a balance between sufficient degreasing performance and high lubricity has not yet been achieved for an actual production process line."

Jan 1, 2018

By S. Hosseinpour

Chromate conversion coatings (CCCs) are usually applied to these alloys to enhance their resistance to localized corrosion and to improve paint adhesion. The special properties of these coatings such as their low electrical contact resistance (ECR) make them suitable for satellites. This study is aimed to develop advanced CCCs with the proper appearance, morphologies and surface roughness and to evaluate their role on the ECR and thermo physical properties on hardened aluminium alloy of Alclad-7075-T6. Coating characterization was performed by means of scanning electron microscope (SEM) and atomic force microscope (AFM). ECR of coatings were measured by special laboratory designed instrument and a and c were measured by Emissometer and Reflectometer respectively. In addition, corrosion performance of the CCC-coated alloys was determined by 168 hr exposing to salt-spray testing in accordance with ASTM-B117. The results of accomplished experiments on the developed CCCs in this study have been agreeable concerning available acceptability criteria for satellite surfaces.

Jan 1, 2007

By W. Lodge, G. Rasmussen

"The carbon-in-pulp (CIP) process has been the dominant gold recovery technology since the 1980s. During all this time carbon measurement, and control of the carbon transfer pumps has been largely manual in nature. Such manual operation inevitably limits process efficiency, potentially resulting in higher gold solution losses, and higher cost of circuit operation. Based on the authors’ experience, average plant solution loss is in the range of 0.02-0.03 ppm Au, as opposed to the general industry target of 0.01 ppm Au or less. Gekko Systems, in conjunction with Curtin University’s Gold Technology Group, has developed a carbon concentration meter, the ‘Carbon Scout’ meter. The meter automatically measures carbon concentration in all tanks, providing more frequent and more precise data. Combined with SIMCIL, a CIP circuit process model which is used to determine the optimum set points for the circuit, the meter should ensure lower gold solution losses, and more efficient operation of the carbon circuit. This paper will review they critical factors for good carbon management, the development of the meter and results from the first plant installation. Additional benefits of the Carbon Scout, including improved health and safety and the opportunity to measure other key variables in the leach/adsorption circuit from one central location will also be described.INTRODUCTION The carbon-in-pulp (CIP) process was first introduced to the gold industry in the early 1950s at the Carlton Mill in the USA (Fast, 1988), with the modern version of CIP becoming fully developed with large scale installations in South Africa in the late 1970s (Laxen, 1982). CIP quickly became the technology of choice for new operations, and for the retrofitting or upgrading of existing operations. In the 1980s the carbon-in-leach (CIL) circuit configuration became the process design of choice due mainly to its lower capital costs. With 40 years of operational experience, CIP/CIL for gold recovery is now mature a technology, whose operations and limitations are well understood. To extract further efficiencies from such technologies, by improving recoveries and/or reducing operating costs, is challenging and may require new approaches to circuit management. Gekko Systems, in association with the Gold Technology Group at Curtin University, has developed the Carbon Scout, an automated carbon measurement device. This device replaces manual measurement of carbon concentration in carbon adsorption tanks, providing more frequent and more accurate data for control of the CIP process. Data from the Carbon Scout can be used to automatically control the carbon forwarding pumps."

Jan 1, 2018

By T. B. Williams

Most geologists have felt the need of a longer base than is ordinarily available when using a Brunton compass or other convenient instrument for taking strikes and dips in the field. To overcome this difficulty a lath or stick with straight parallel sides is frequently used. This accessory adds to the accuracy of the work, but it is a decidedly inconvenient one for the geologist to carry, especially if he be heavily loaded or is travelling on horse-back or through thick brush on foot. The writer has abandoned its use in favour of a sturdy two-foot carpenter's rule. The rule preferred is manufactured by J. Rabone and Sons, Birmingham, England. It is provided with a good level-bubble set in one of the limbs, and a scale, of the protractor type, graduated to five degrees through 180 degrees, attached to the main joint at the middle of the rule. (See Figure 1). For an instrument of its kind it is very accurate, and, in addition to the uses mentioned below, it 'is a handy thing to have around any camp. It is frequently used when plotting roughly in the field and for a protractor when one is not available. When not in use it may readily be carried in the top of the high-boot or legging. Ordinary strikes are measured as illustrated in Figure 1, the compass being held against the rule, which is in a horizontal position. Dips may be measured in a corresponding way by holding the Brunton compass against the extended rule, which is thus used merely as a straight edge. It is usually much more convenient, however, to ? use the rule only for this purpose, in which case one foot of the length rests as a straight-edge against the rock surface. This adaption is shown in Figure 2.

Jan 1, 1929

By L. Henry Smith, David C. Arthur

"The Williams Mine is Canada’s largest gold producer, with annual production of 450 000ounces from 2 300 000 tonnes of ore. Highly mechanized and automated underground mining practices are employed in order to achieve and maintain high levels of productivity and minimize costs.The mine ventilation system is modified to include a new vent raise and variable pitchvane-axial fan. This addition allows several fan installations underground to be decommissioned. A substantial net savings in installed horse power is achieved.Heating costs associated with under-ground ventilation air are a significant portion of mine operating costs. Air heating costs are substantially reduced by recovering heat from upcast exhaust air, minewater and compressor cooling circuits. This waste heat is used to supplement propane fired air heating systems for underground ventilation air. An additional benefit is the availability of a heat sink for summer cooling of the compressors.System design, energy savings data and payback calculations are presented."

Jan 1, 1996

By LeRoy A. Thorssen

The use of lightweight aggregate as a constituent of concrete is not a recent development. Pumice was used by the early Romans, in pozzolana cement concretes, in the construction of many of their works. However, the recent development of manufactured lightweight aggregates, such as the expanded shales, vermiculite and perlite, has created a possible use for a whole new group of Portland cement concretes. Concrete can now be produced with unit weights ranging from 30 to 150 pounds per cubic foot and with various insulating, fireproofing, acoustical and structural properties. The tonnage of such materials being used has increased considerably in each of the past ten years, and can be expected to increase for the next several years as availability of the aggregates becomes more widespread and the properties of such concretes become more thoroughly investigated and more generally known. LIGHTWEIGHT aggregates of many types have become avail-able to the construction industry in most localities on this continent

Jan 1, 1963

By T. G. Edgeworth

Some of the historical background of the industry is reviewed, with reference to the different types of reduction cells in use for aluminum smelting. Factors to be considered in cell des1gn involve capital, power, and operating costs. The trend is apparently toward larger cells. The industry is studying new construction materials for cell linings, as well as alternate electrolyte compositions and other design changes which will improve productivity and energy efficiency. The aluminum smelting activity in other countries is briefly reviewed. TODA Y'S industrial production of aluminum is still based on the simultaneous discoveries made in 1886 by Charles Martin Hall in Ohio, and Paul Heroult in France. Up to that date, only about 50 tons of aluminum had been produced in the world, and the price at that time was about $5 per pound. Sucl1 figures must be contrasted with the present world aluminum smelting capacity of over five mil-lion tons per year, and a price of about 25 cents per pound.

Jan 1, 1962

By A. Fischersworring-Bunk

The new inline six spark-ignition engine is the realization of BMW's concept of efficient dynamics at high technological level to achieve the attributes of low weight and high efficiency, The paper presents different aspects of the development and manufacturing of BMW's inline six-cylinder engine magnesium-aluminium composite crankcase, Reference will be made on the AJ magnesium alloy optimization approach to balance between mechanical properties and the high pressure die cast ability requirements, Next to this aspect some mechanical design issues will be covered, with CAE methods playing an instrumental role in the early project stage for the assessment of the compound concept, Due to the compound design chosen, the interface posed challenges to both design and productions, A set of novel techniques has been used to cope with these tasks.

Jan 1, 2006

By J. W. Cox, W S. Jones, A E. Chase

For a long time the Oil Industry has been looking for a logging tool which can determine the quality of the cement job behind casing. Older methods such as Temperature Surveys and Radioactivity Surveys might detect the presence of cement behind the casing, but short of production tests, it was impossible to tell that the producing zones were adequately sealed off from adjacent zones. A new logging method, which is called the •Cement Bond Log, operates on the principle that a sonic pulse transmitted by the casing is greatly attenuated when the casing is strongly bonded to an outer annulus such as cement. The down-hole tool consists of a source of sonic energy which is detected by a receiver situated a few feet away from the source. The amplitude of the detected energy is measured and the resulting signal transmitted to the surface where it is recorded versus depth. Amplitude is a function of attenuation and thus the log is readily interpreted.

Jan 1, 1961

By O. Hyvärinen

Outokumpu has developed a new chloride leaching process called HydroCopper®. In this process copper sulfide concentrates are leached at atmospheric pressure in concentrated sodium chloride solution using cupric ions as the oxidant. Copper is recovered from the purified leach solution by precipitating cuprous oxide, which is then reduced to pure copper and further melted and cast directly into copper products. The key reactants: sodium hydroxide, hydrogen and chlorine are generated from the spent sodium chloride using chlor-alkali technology. An important feature in the HydroCopperTM process is that the gold contained in copper concentrates is leached as chloride complexes and recovered from solution by activated carbon. Conditions for the leaching of gold-bearing pyrite can also be achieved in the chloride system by optimizing the redox conditions. This paper deals with the basic factors affecting gold leaching from copper sulfide concentrates. Opportunities for the recovery of refractory gold associated with arsenopyrite and pyrite will also be discussed.

Jan 1, 2005

By J. E. Dodge

Tasu, currently an open-pit operation, services the primary crusher from two areas by ore-pass raises. The problems encountered and advantages gained are discussed. Mine equipment and operating practices are covered, together with blasting practices, line drilling and the pre-shearing necessary to stahilize the pit walls.

Jan 1, 1968

By BRIAN HITCHON

Calcium, magnesium, bromide and iodide extraction from formation waters for use as industrial minerals has occurred in several countries, but not yet in Canada. Potential commercial brine fields exist in th e Upper Devonian Beaverhill Lake Formation of so uthern Alberta, and the Middle Devonian Elk Point Subgroup of north-central Alberta, f rom which calcium, magnesium and bromide are potential products. Iodide contents in fo rmation waters f rom the Upper Cretaceous Belly River Formation and the Lower Cretaceous Viking and Bow Island fo rmations in central and southern Alberta are at the lower range limit of commercial iodide-bearing formation waters elsewhere in the world. Available information is insufficient 10 outline potentially commercial areas in Alberta, but such info rmation can be most easily obtained f rom test borings for shallow natural gas. Lithium is not now produced commercially f rom formation waters but its content should be monitored in view of f uture increased demand for this metal.

Jan 1, 1984

By T Nakamura, M. Itoh

Most of the used cathode ray tube (CRT) glass in Japan, which contains lead oxide, was exported and recycled in overseas factories of new CRTs. However, domestic treatment and recycling of waste CRT glass has become necessary because overseas CRT factories have shut down and exports of CRT glass have stopped. Some of the waste CRT glass recycled domestically is charged in lead blast furnaces instead of silica flux, because there is no local reproduction route for glass that contains lead. However, the mass of CRT glass that can be treated in this manner is limited because of its high silica content. Consequently, additional treatment methods for waste CRT glass are required so that more can be used as a lead smelting material. In this study, waste CRT glass was treated with hydrofluoric acid to dissolve the silica contained in the glass, and the dissolved lead was recovered by precipitation. Lead metal was recovered by electrodeposition from the prepared hexafluorosilicic acid solution.

Jan 1, 2011

By R. Gutray, J. E. Grainger

This paper deals with the use of a cement-deslimed mill tailings mixture for a scraping floor in cut-and-fill stopes at Madsen Red Lake Gold Mines Limited. It describes the mixing and placing procedures and the precautions used with respect to the floor while mining in the stopes. Details of the mix are presented, and advantages and disadvantages discussed. The paper concludes with a brief outline of the costs.

Jan 1, 1966

By S. Castro

Hydrolysis of metallic ions depends on pH and the products of hydrolysis either activate flotation or can lead to inadvertent activation of gangue particles, but can also depress flotation of valuable components. One of the most recently studied topics is the use of seawater in flotation. Seawater is a concentrated NaCl solution (about 0.6 mol/L) that also contains considerable amount of Mg2+ and Ca2+ ions. The hydrolysis products of Mg2+ strongly depress flotation of molybdenite over the pH ranges over which they form in the process water. This effect can be eliminated by removal of hydrolysing ions from the process water or by carrying out the flotation at the pH over which such a hydrolysis can be avoided. The former can be exemplified by prior precipitation of the harmful hydrolysing ions as, for example, in the University of Concepcion Patent. The latter can be exemplified by the use of metabisulfite to depress pyrite in the flotation of Cu-Mo sulfide ores in seawater, the process that is carried out at much lower pH, which avoids formation of Mg2+ hydrolysis products.

Jan 1, 2017

By E. Ghali, N. Sorour, G. Houlachi

"The binary Fe53Mo47 and ternary Fe54Mo30P16 coatings have been electrodeposited from citrate-based electrolyte on mild steel (MS) substrates. The electrodeposition has been conducted for 6 hours at 20 mA cm-2 and 30°C. The electrochemical tests were carried out in chlorate solutions containing 300 g L-1 NaCl and 4 g L-1 K2Cr2O7 at pH 6.4 and 80°C. A number of surface characterization techniques such as SEM-EDS, XRD and EMP were used to study the microstructure of the alloys. The electrocatalytic activity of these coatings was investigated using steady-state polarization and galvanostatic technique. This study revealed that the Fe-Mo-P coating could be considered as a promising cathode material for the hydrogen evolution reaction (HER). The results showed an important decrease of hydrogen overpotential for Fe-Mo-P alloy as compared to that of Fe-Mo and especially MS which is a traditional cathode in chlorate industry. The HER overpotential for Fe54Mo30P16 at current density of 250 mA cm-2 was decreased by 30% in comparison to that of MS (1029 mV), and by 16.5% to that of Fe53Mo47 coating (857 mV).INTRODUCTIONSodium chlorate is used for manufacturing of several daily consumption products. This chemical is mainly employed for the production of chlorine dioxide (ClO2) that is a bleaching agent used in the pulp and paper industry. The ClO2 is also consumed for generation of perchlorates, chlorites and other chlorates, as an herbicide and in uranium processing (Cornell, 2002). Sodium chlorate is produced industrially via following overall formula in un-divided electrochemical cell (Nylén & Cornell, 2009):"

Jan 1, 2016

By H. L. Cameron

General Statement In July, 1948, experimental aerial photography o shallow water zones on Northumberland strait was carried out by the Nova Scotia Research Foundation. This work was designed to test the feasibility of aerial photography for coastal surveys o various types, including seaweed and bottom detail surveys. In the course of the work at Lismore, undersea faulting was noted visually and was later clearly apparent in the photographs. In order to prove beyond doubt that the lineations photographed are actually faults, a ground check was made, and terrestrial stereoscopic photographs were obtained of these features where they intersect the shore line. There can be no doubt of their nature, and the type of faulting is probably thrusting due to compressive forces. This is indicated by the successive right- and left-hand displacements on intersecting faults. The age of the fracturing is post Lower-Pennsylvanian (Lismore) and is correlated with similar compression faulting in western Cape Breton. As far as can be ascertained, this is the first time that subsea faulting has been photographed, though it is quite possible that similar structures have been observed elsewhere. Location and Area Lismore is on Northumberland strait, approximately thirty-five miles east of Pictou (see index map, Figure 1). The area mapped from aerial photographs (Figure 2) is a strip approximately two miles long by a quarter of a mile wide. Figure 3 shows a stereo-pair of the aerial photographs used to construct this map. The terrestrial stereoscopic photographs (Figure 4) show one of the faults.

Jan 1, 1949

By F. L. Pellet, S. Maiolino

"The determination of rock bolt contribution to reinforced joint shear strength is still a challenge, especially for assessing reinforced rock mass stability. For this purpose, several experimental studies have been performed during the last decades, mostly on small scale rock joint and bolt specimens. However, to accurately assess the rock bolt contribution, scale effect has to be accounted for. For this reason full scale lab tests are required as an alternative to in situ tests for which boundary conditions are more difficult to control.In this paper the results of an experimental program carried out with a large shear box, dedicated to test bolts in full scale conditions is presented. Different rock bolt diameters and different rock bolts inclination with respect to the shear plane were tested Experimental results were satisfactorily compared with an analytical model which is able to compute the contribution of the rock bolt to the shear strength of the joint as well the associated displacement of the joint. These conclusions allows us to validate the model in order to help the designer of reinforced rock engineering structures, such as slope or underground openings, to precise the optimum installation of rock bolts. INTRODUCTIONFully grouted rock bolts are commonly used for rock masses reinforcement to ensure the stability of rock slopes and underground cavities. For this purpose, the determination of rock bolt contribution to reinforced joint shear strength is of the utmost importance. During the last decades, several experimental studies have been performed to investigate the behavior of bolted rock joint. For obvious reasons, almost all the experiments were achieved on small scale bolted rock joint specimens (Bjurström, 1974; Azuar, 1977; Dight, 1983; Egger & Fernandes, 1983; Schubert, 1984; Spang & Egger, 1990; Egger & Zabuski, 1991). These studies made it possible to assess the influence of different parameters such as the bolt’s diameter, the number of bolts, the angle between the bolt and the joint, the nature of the rock, the friction and the dilatation angle of the joint. However, to accurately assess the rock bolt contribution, scale effect has to be accounted for (Vallier et al., 2010). For this reason full scale lab tests have been performed as an alternative to in situ test for which boundary conditions are more difficult to control."

Jan 1, 2015

By J. M. B. Scarborough

This paper deals with measures taken to maintain effective operation of heavy-duty equipment in open-pit mining. at Pine Point, N.W.T., during periods of extreme cold weather. The points covered include equipment modifications designed to improve cold-weather performance, effective lubrication of machinery that is vulnerable to extreme cold and operating procedures designed to prevent equipment damage.

Jan 1, 1966

By Gabriel G. Walton

Conventional numerical modelling tools for analyses of underground excavations are well suited for modelling elastic behaviour and yield response of geomaterials with very simple constitutive behaviour. Non-dilatant elastic and perfectly plastic behaviour is most commonly used for preliminary analyses in the absence of the data required to consider more complex behaviours such as strainweakening and dilation. For truly brittle models, this deficiency is more acute. Current state of practice allows only for reliable estimation of the volume of failure, but not for any prediction of displacement. In fact, there is no consensus in rock engineering regarding the most accurate approach or most suitable tool to model the magnitude of the plastic deformation that strain-weakening or brittle rocks experience at tunnel boundaries, particularly when support is incorporated into these models. This problem is largely a function of a poor understanding of how inelastic dilation occurs in different types of rockmasses, the rate controls on strength loss and volume change during yield, and the complexities of rock-support interaction in yielding conditions.

Jun 1, 2012