Search Documents

By David L. Sprott

This paper presents an evaluation of underground-to-surface haulage options for a relatively large deposit. Specifically, it presents a recommended haulage option to provide the greatest value to the Project. Options considered included conventional truck, trolley-truck, conveying and shaft hoisting. The work was done at the level of a preliminary assessment as input to an internal pre-feasibility study. The Base Case for the analysis in this study was a Long Hole Open Stoping option (LHOS) using conventional truck haulage. Two scenarios were considered for the evaluation and included: 1. The current resource to ~700 m depth. 2. An expanded resource to ~825 m depth. The haulage options evaluated included three trucking options, three conveyor options and two shaft options. The paper presents the results from evaluating these options within the two mining scenarios using a Discounted Project Cost (DPC) comparison. Recommendations are made for the options that will provide the greatest overall value to the project.

May 1, 2008

For the last few years, a new and innovative technique has been successfully used to determine refractory and castable thickness in various metallurgical vessels. The acousto ultrasonic-echo (AU-E) technique uses stress waves to detect metal penetration and delaminations within refractory linings. In addition, it is capable of measuring the thickness of refractory layers and build-up material. The inspection and measurements can be carried out while the furnace is in full operation. The present paper discusses the principles of the AU-E technique, and its advantages and limitations. A number of case studies are presented to demonstrate various capabilities of this new Non-Destructive Testing (NDT) technique.

Jan 1, 2005

By Terry Aben

Outline ?Review of standards that can be used to identify current coating conditions and optimal points to perform coating maintenance. ?Identify how standards can be used to extrapolate the future condition of coatings to achieve predictive maintenance planning. ?Demonstrate how the above can be combined with project estimating to generate a data driven, quantitative, predictive, risk-based asset integrity maintenance program for Protective Coatings. The Value of Asset Integrity Programs ?Maximize the benefit produced from the investment in maintenance spending. ?Get the best bang for your buck! ?Don?t perform maintenance work before it is necessary ?Money is invested early with no increase in the service life extension. ?Don?t delay until it is too late. ?Planned Maintenance is far less costly than Reactive Maintenance. ?Identify the Optimal Point for Maintenance.

Nov 1, 2011

By Daniel Cluff

Frozen backfill for mining operations in permafrost must be delivered in such a state so as not to thermally impose on the host rock surrounding the filled stope. The placement process, the material strength demand, and the freezing time delay are the parameters that control the applicability of the method. A two-year research program was carried out in the field and using a laboratory-scale apparatus, designed to simulate a pour of frozen backfill, to study the mixing, thermal properties and segregation. The frozen rock and tailings must be at a below zero temperature and get fully wetted so the surfaces cause adherence of the particles to one another and enhance the solidification of the poured backfill. The results provided a recipe and a process for mix design for open stoping operations in cold regions. The testing evaluated the sensitivity of the test parameters that included the amount of water added in the mix, the temperare of water, the rockfill/tailings ratio, and the temperature of solid constituents.The paper presents the result of this environmentally friendly, innovative technology. The distribution of the materials and the mixing process are instrumental in achieving the properties required for open stoping applications.

Oct 1, 2010

By J. W. Smith, J. G. Eacott, D. H. Napier

"Three hydrometallurgicat processes (Noranda chloride leach, B. C. Research biological leach and Sherritt-Cominco activated oxygen leach) and the Noranda pyrometallurgical process have served as the basis for design projects in the final year of the chemical engineering program at the University of Toronto. Each member of a team of five or six students devotes about 200 hours to the project and the final report is expected to include an economic analysis.None of the processes has been developed to full- scale plant, nor, in the case of the B.C. Research and Noranda processes, were pilot plant data available. Nevertheless, the designs developed provide a useful basis for a preliminary estimate of capital and operating costs and for a preliminary assessment of project feasibility.This paper discusses the approach used in the design projects with respect to engineering and economic aspects, and outlines the educational features and benefits of such a program as well as some of the problem areas that arise.IntroductionAs part of the undergraduate degree course in chemical engineering at the University of Toronto, students devote some 200 hours to a design project in their final year. Hydrometallurgical processes, not yet proven at the commercial scale, have been selected for study. The students are required to develop laboratory and / or pilot scale results into a conceptual plant design, using sound engineering principles. Capital and operating costs are then determined and a preliminary feasibility study and economic analysis are carried out."

Jan 1, 1986

By T. Shariff

Titanium alloys have found increasingly wide range of applications in aerospace, chemical, medical, sporting, power generation, oil and gas extraction industries mainly due to the low density, high mechanical property characteristics, biocompatibility, and excellent corrosion resistance. In the manufacturing routes of their finished products, welding has been a key technique used and always been a main concern requiring the stringent compliance to the well defined process. Conventionally, gas tungstenarc (TIG), gas metal-arc (MG), plasma arc, and electron beam welding processes have been used to weld titanium alloys. Nowadays, laser beam welding has provided great challenging applications for titanium alloys due to the low and precise heat input, deep and narrow fusion zone, small heataffected zone, low thermal distortion and high productivity. At the NRC Institute for Aerospace Research, some R&D work has been undertaken for titanium alloys using laser beam welding process. These investigations have mainly concentrated on optimizing the welding process as well as understanding the fundamental process-structure-property relationships. In this invited keynote presentation, the research progresses obtained and the main issues encountered in laser welding of titanium alloys will be briefly summarized.

Jan 1, 2011

By C. E. McCoy

This paper will discuss briefly loader shovel requirements and then present a detailed survey of electrical drive systems to meet these requirements. The survey in general will deal with the various electrical provisions for shovel drives, along with the advantages and disadvantages, and in particular will discuss the MG set and static D. C. drive systems. Also included will be some insight into the requirements for optimum electrical power at the shovels.

Jan 1, 1979

By Michel Gamache

This paper describes a system that manages and assigns vehicles in real-time in an underground mine. Each dispatching decision takes into account the traffic on the road segments of the mine network, whether bi-directional or unidirectional, and ensures that each LHD (Load-Haul-Dump Vehicle) arrives in the right orientation at loading and dumping points. Such systems can be used for two main purposes: 1) as a strategic planning tool and 2) as a real-time managing and optimising system for operations. Using a simulator in conjunction with the fleet management system, it is possible to accurately estimate the impact on productivity of decisions such as the development of waiting areas (bays, sidings), or the addition (elimination) of vehicles to the fleet in operation. Moreover, when used in for real-time dispatching, routing and scheduling of vehicles, the system can optimise production with respect to various assignment criteria such as minimising the cycle time or minimising the deviation from an optimal production plan. Dispatching, routing, and scheduling are handled simultaneously, taking into account the mine status, operational constraints, and all available information.

May 1, 2001

By Hans Lundberg

Magnetic methods have been used for more than three hundred years in prospecting for magnetic ores. More recently magnetic methods have been used for finding salt domes and studying certain geological formations. A number of instruments have been developed and substantial improvements made as to their sensitiveness and accuracy. Papers and articles written on magnetic methods are generally elaborate and technical, and the average prospector finds it difficult to obtain the necessary information as to how to operate the simple magnetic instruments to the best advantage. The miner's compass, dip needle, and inclinator are, indeed, very useful instruments and are easy to handle, and a great deal of valuable information can be gained if the instrument is properly operated and the results correctly interpreted. The lack of knowledge of the fundamental principles, however, has caused a great deal of disappointment. Other and more elaborate geophysical methods have recently come into the limelight, and the prospectors seem to have lost a great deal of interest in the dip needle. This is much to be regretted, because magnetic methods have a particular field of use. The present article is an attempt to help the prospector regain interest in the magnetic instruments and to show the use and application of a simple magnetic survey. If the prospector expects some useful help in his work, he must, of course, know the instrument, know how to take the readings, and know how to plot and interpret the observations.

Jan 1, 1929

By C. Graham

Mechanisation has been a predominant theme of the past 50 years in the mining industry, particularly underground mining. As the level of technology employed has increased, the anticipated productivity gains have not been realised and the differences are not explained by the demand for higher standards of safety and security. Now, mining costs are so high and productivity so low that the resultant return on investment for many Canadian operations has fallen to levels considered unacceptable in a competitive capital market. Simply continuing technological development cannot reverse this trend and its financial implications. The focus on technological development has distracted us from some basic truths. Systems that are more complex are more likely to fail and cost-effective processes depend on the continuity of productive activity and the flow of material. When putting these facts together, it becomes clear that in a system that has fixed external conditions, the single most crucial issue is the effective management of the operational cycle. By its nature, technology focuses our attention on what gets done and how it gets done, while the crucial issue is the increasingly longer periods in the operational cycle when nothing productive is being done. What is required is to match the level of technological complexity to the fixed system conditions, which are virtually unchangeable. This paper looks at the overall system and objectives and attempts to present an appropriate level of technology for the Canadian mining industry, now and in the foreseeable future.

May 1, 2004

By W. Petruk

"D. Doyle How large is the beam to which you referred? Are we considering Watts, Griffis the probe of a 1 micron sized particle?& McOuatReply Yes. The beam would be about 1 micron. We could enlarge or reduce it depending on the current in-put.D. Doyle Then chemically bound material we might not see. If you are restricted to 1 micron then you would not be able to separate things smaller than this. Is this not so?Reply We won't be able to analyse it but we will see it as the scanning electron microscope has a resolution down to about 0.1 microns. We should be able to get the general composition of such a grain plus its surrounding grains. We feel we can then make a reasonable estimate if it were as small as 0.1 microns. An accurate analysis would be achieved with grains of 3 and 4 microns.D. Doyle Would this have an application in the hydrocarbon field?Reply The lowest atomic number would be sodium. We wouldn't be able to go below that atomic number. Anything with sodiumor a larger atomic number would enable us to analyse the carbon.M. Fairwether Do you have any policy relating to priorities. For instance areCominco companies going to be limited in the amout of samples permitted to give everyone a chance because quite frankly our company, and I'm sure all base metals companies can hardly wait for the installation of this equipment. I can forsee two years back-log of work in the first month.Reply Quite frankly, I haven't looked at this. At the present time the work is under the START program but I suppose we will have to look at possible changes. Anything under the START program has first line priority.B. Thorndycraft Will the briquetting of samples be automated as well? Pinson MiningReply No, not at this point. Our polish section laboratory is first-class and can turn out 18 polish sections a day which is more thar we can handle.B. Thorndycraft With the capability of this machine to operate in a hands-off manner perhaps it could start to look for the 5 micron gold particle in tailings?Reply I have such a program using a wave-length spectrometer rather than the energy dispersive. The wave-length spectometer is about 10 times as sensitive and would scan the section much faster. A one inch diameter polished section would be scanned in about 7 hours for anything 1 micron or larger."

Jan 1, 1984

By J. Olsson

The paper describes and discusses the use of stainless steels for leaching plants emphasising the duplex family, i.e., austenitic-ferritic stainless steels. This group has generally twice the proof strength of the more common 300-series austenitic grades, which implies possibilities to reduce the gauge at construction of pressure vessels and atmospheric tanks and vessels and thereby possibilities to reduce the weight. The duplex grades have also higher surface hardness resulting in better resistance to mechanical wear, i.e., abrasion and erosion corrosion. The lower contents of nickel and molybdenum imply lower cost and a more stable price considering the present market situation for these alloying elements. Corrosion data from laboratory and pilot plant tests, as well as examples of applications of duplex and highly alloyed austenitic grades, are presented. Cu2007 - Volume IV (Book 1) The John E. Dutrizac International Symposium on Copper Hydrometallurgy Edited by P.A. Riveros, D.G. Dixon, D.B. Dreisinger, M.J. Collins Toronto, Canada,

Jan 1, 2007

By K. A. Lewandowski

Agglomeration of ore used in heap leaching allows for the immobilization of fine particles that would otherwise migrate and cause permeability problems in the heaps. For copper ore, binders are needed in order to make stable agglomerates. However, the majority of binders break down when introduced to an acidic environment, allowing fine particles to be released from the agglomerate surfaces. These particles migrate through the heap impeding solution flow, leading to a decrease in metal recovery rates. The authors have developed a series of testing procedures to determine the acid resistance of several binders. Only five binders were shown to be acid resistant in soak tests, decreasing fines migration by up to 93%, compared to tests which were agglomerated with leach solution, raffinate, as a binder. Flooded percolation column testing also showed that these binders were able to reduce the "slump" of the ore by up to 82% and increased the hydraulic conductivity by up to 90%, when compared to agglomerating with leach solution alone. The use of binders in the agglomeration of copper ore also showed no negative effects on the bacterial populations throughout a leach cycle.

Jan 1, 2007

By Dwayne D. Tannant

Digital photogrammetry allows rapid, remote measurement of millions of points, thus providing an unprecedented amount of spatial information. Research is being conducted to explore practical applications of digital photogrammetry for monitoring, surveying and mapping in surface mines. The performance, accuracy and operational ease of digital photogrammetry are discussed and practical aspects of conducting digital photogrammetry surveys are reviewed. Case histories from coal, diamond and limestone mines are presented.

May 1, 2006

By M. DeLucia

"Over the past 15 years, technical innovations have improved the properties and performance of monolithic refractories. As these improvements have occurred, aluminum cast-house refractory selections have changed from brick to monolithic refractories supplied as either cast in place, or precast, ""Big-Block"" installations. A review of the properties of monolithic and brick refractories is presented, as well as the technical advantages of brick for highly demanding applications. Operating conditions and issues such as temperature, alloying, corundum growth and other variables are also reviewed."

Jan 1, 2004

By Marke Wong

? Vietnam?s economy is growing so fast that gross domestic product (GDP) growth remained above 8% in 2005 and exports are rising steadily at 25% per year. ? Demand for electricity is expected to increase 18% per year through 2010 requiring an additional estimated 7,547 MW before 2010 ? Domestic coal demand is expected to be over 45 Mt by 2010. ? The Quang Ninhcoal deposits are estimated at 6.5-7 billion tons (350m) Vietnam News Agency. Saturday, May, 6, 2006. ? National resources are now estimated at 10 billion tonnes; not including a relative new coal bed discovery estimated at 210 billion tonnesin the Red River Basin.

May 1, 2006

By Tom Brady

A major focus of ground control research presently being conducted by the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) is to incorporate weak rock masses (such as are associated with operations in the Carlin Trend in Nevada) into existing design relationships. The original database that led to most of the empirical design relationships presently employed in hard-rock mining was derived from fair-to-good-quality rock. In this study, the relationship between weak rock quality and opening design (nonentry/entry methods) is being investigated. The common factor in all mines is a weak back or wall. This work attempts to provide tools that will enable a mine operator to make economic decisions that will also ensure a safe working environment.

May 1, 2003

By William H. Pomroy, Kenneth E. Hjelmstad

An underground mine fire can seriously threaten the lives of all personnel in the mine. This fact makes fire emergency planning a high priority in the mining industry. A fire emergency plan includes a means of warning miners of the existence of a fire, and the need to evacuate or retreat to a place of refuge. The warning alarm must be fast and must reach all miners, regardless of their location or work activity. Means of fire warning are varied, and include such methods as stench, flashing lights, telephones, and word-of-mouth (messengers). Unfortunately, none of these methods are entirely satisfactory. Stench can be slow and seldom achieves total mine coverage, especially in high-back room-and-pillar mines with low ventilation velocity. Telephones are effective only where personnel are close enough to hear the phone ring. A novel fire warning alarm system has been developed by the U.S. Bureau of Mines which enables instantaneous warning of all underground personnel. The warning alarm is sent by an electromagnetic signal which penetrates through mine rock from a transmitter to small person-wearable receivers. Each miner's cap lamp battery could be equipped with a small receiver and when a fire or other emergency occurs the miner could be alerted to the danger by a blinking of the cap lamp. Testing of prototype equipment has demonstrated that the transmitted signal is capable of penetrating through over a mile of mine rock and activating the receiver. This paper describes the theoretical basis for through-the-rock ultra-low frequency electromagnetic transmission, design of the prototype transmitter and receiver, test results, and status of commercial development of systems utilizing this technology.

Jan 1, 1994

By A. C. Bonnier

"INTRODUCTIONI have been asked to make available our method of determining the ""Live Inventory"" within a gravity type thickener. The ""Live Inventory"" being that tonnage compatible with the optimum underflow density that satisfies the process requirements.One prerequisite of the calculations is the proper determination of the final pumpable underflow density. A further requirement is that, prior to shutdown, the thickener has been operated properly, particularly that it has not been operated for storage capacity.Until recently I had few chances to check the method. However, I was most fortunate to have had a recent opportunity covering several months on a 300 ft diameter thickener at a plant in the U.S.A., wherein the method was tested and verified many times. The method proved accurate in that our calculated tonnage checked with the actual dried physical inventory of the drying facility.At the precise moment that the feed to the thickener was shut down, a per cent solid determination was made at the critical place and the tonnage in ""Live Inventory"" determined. Let us say that at the moment the thickener U' Flow solids was 20%. The thickener then was allowed to cperate until the U' Flow solids dropped below 20%, at which time the thickener was deemed to be relieved. Anything much less than 20% was not suitable to the subsequent centrifuge operation.Most large metallurgical thickeners have a configuration of three slopes at the thickener ""bed"". These slopes are dictated by the raking blades and are shown on the manufacturers' erection drawings. The first slope is from the outer periphery and generally takes up a distance of about 60% of the radius, the second slope generally taking up the remaining 40%. Within this 40% area, there is usually another slope taken up by the cone on ""B"" type thickeners or an actual steeper inner slope on ""C"" type thickeners."

Jan 1, 1989

By R. D. Brown

Ever since British Columbia started the ball rolling in 1974 with the introduction of its now-defunct Mineral Royalties Act, all Canada's resource-based provinces have significantly altered their mining tax systems. The last resource-based province to abandon its pre -1974 mining tax structure is New Brunswick, which introduced a new mining tax regime in the summer of 1977 to take effect from April 1 1977. The new structure, which represents the outcome of considerable study and discussions with industry representatives, contains some intriguing concepts which make Nero Brunswick's new mining tax system unique among the Canadian provinces.

Jan 1, 1977