Search Documents

By S. G. Shabestari

Thermal analysis is a tool that is generally employed to predict the structure of the alloy before the actual casting is carried out. By cooling a sample of the molten alloy and recording the temperature-time curve, important solidification events may be analyzed by using the first derivative-cooling curve. In this research, strontium is added to (AS5U3G) 319 aluminum alloy and its influence on the formation of intermetallic compounds e.g. Al15(Mn,Fe)3Si2, Al2Cu, Al5Mg8Cu2Si6 formed during pre- and post-eutectic reaction have been investigated. Also any changes in solidification parameters such as temperature of Al-Si eutectic under cooling and temperatures of nucleation and growth of each phases caused by strontium addition, have been determined via the first derivative cooling curves. The effect of strontium on the formation of various intermetallic compounds has been studied by using very accurate thermal analysis equipment and the microstructures were analyzed using an optical microscope. The various phases reported in this paper were identified using Scanning Electron Microscopy (SEM) and linked to Energy Dispersive Spectroscopy (EDS). Formation of all pre- and post-eutectic phases was interpreted by comparing the phases formed in the microstructure and the reactions detected by using cooling curves. The results of this research indicate that thermal analysis technique can be used as an on-line process control in the production lines in aluminum casting industries.

Jan 1, 2004

By Narasimha Mangadoddy, Balraju Vadlakonda

"Bubble size distribution, bubble rise velocity and gas and solids hold-up are the key major hydrodynamic parameters that are extensively used for column flotation design and performance evaluation. The distribution characteristics of mean gas hold-up is studied using electrical resistance tomography (ERT) coupled with pressure transducers (PT) in column flotation. The ERT technique facilitates non-invasive and nonintrusive visualization of different flow regimes even in the presence of particles in a column flotation. The effect of superficial gas velocity, feed flow rate and slurry height in the column on mean gas hold-up and its radial distribution has been analysed for both two-phase and three phase flows. Experimental results show ERT coupled with PT is suitable as an online monitoring tool to provide useful information on the three-phase flow hydrodynamic parameters of the column flotation. The tomography images, which were generated using a modified sensitivity back projection algorithm, are employed to explore the influence of parameters in two phase flow in column flotation. Mean gas and solids hold-up values extracted from ERT have been critically analysed for the column operating in various flow regimes. Gas hold-ups and solid hold-ups results using ERT are in very good agreement with conventional estimation and correlations obtained using pressure transmitter methods. Meanwhile, the results show that the gas hold-ups in the centre region increase constantly with an increase in the superficial gas velocity, whereas solid hold-ups distribution is very heterogeneous for high gas velocity. Furthermore, the results also indicate that ERT is a very powerful tool for diagnosing the 'inside' flow behaviour of gas –liquid–solid three phase flow in columns operating for a wide range of flow regimes.INTRODUCTIONColumn flotation is perhaps the most significant technological innovation in flotation machinery and its successful introduction in mineral processing plants. There has been a lot of attention in understanding the various mechanisms that take place during operation. Due to many reasons column flotation has been found to yield better performance than conventional flotation cells, particularly with fine particles (Honaker & Mohanty, 1996). Due to complex flow behavior in nature, the performance of column flotation influenced by on flow characteristics of the process, (Jena, Biswal, Das, & Reddy, 2008). Previously basic research is carried out to evaluate the effect of the hydrodynamic parameters on performance of column flotation (Finch, J.A.;Dobby, 1991). Many techniques have been developed that could be used to experimentally analyse the hydrodynamics of column flotation. Tomography techniques are well sound to investigate the hydrodynamics for process equipment. Among that, Electrical resistance tomography (ERT) has been used in various industrial investigations for visualization of the concentration profiles and characteristics of the fluid dynamics in gas–liquid two-phase systems (Wang, Dickin, & Mann, 1999; Williams, R.A; Wang, 2000). ERT is an imaging technique to analyse the internal flow behavior non-intrusively. ERT provide very useful tools for measuring and monitoring of column flotation process on line. Due to its high speed capability, low cost measurement, robust sensors, ERT is considered to be the most powerful tool among other tomography techniques such as positron emission tomography (PET), magnetic resonance imaging (MRI), optical and infrared tomography. Application of ERT has extended in process systems due to its improved speed of data acquisition, sensitivity, flexibility and noise immunity. In multiphase flow of bubble columns, gas hold-up and solid hold-up are explored by using the coupling of ERT and difference pressure method (Jin, Han, Yang, & He, 2010)."

Jan 1, 2016

By A. Galibois, H. Monette, J. L. Collins

This paper deals with the problem of caving, which occurs in varying degrees in blast holes before loading. It is shown that the distribution of the amount of caving in materials may be described by a gamma density function. A decision model to determine the optimal depth of over-drilling 'in order to minimize the expected additional cost per hole is described. Two different policies are discussed. In addition, charts which permit the mine operator to realize significant savings have been drawn for different actual situations.

Jan 1, 1971

By V. Feldman, I. Holl, J. Zampini

"The Renard Mine, 100% owned by Stornoway Diamonds, is located approximately 250 km north of the Cree community of Mistissini and 350 km north of Chibougamau in the James Bay region of north-central Québec. The project benefits from a large and growing resource, good mining conditions, strong social acceptance, a modest environmental footprint, and the development of direct-to-mine road infrastructure. Construction began on July 10, 2014; following the completion of a 946 million CAD project financing transaction. Now completed, the mine is the first diamond mine in Québec, and one of only six in Canada, employing approximately 500 people. First ore was delivered to the plant approximately 5 months ahead of schedule on July 15, 2016. Commercial production was declared on January 1, 2017. In general, the project ramp up has been characteristic of a type 1 McNulty curve. One of the challenges during production ramp-up was a redesign of processed kimberlite dewatering (replacing the dewatering centrifuge with two stages of hydrocyclones and a dewatering screen). A processing opportunity captured by Stornoway was the design and installation of an ore sorting facility which rejected free waste rock from the valuable host rock; kimberlite. Through tackling both challenges and opportunities, Stornoway has realised and is now exceeding their original design tonnage.PROJECT DESCRIPTION Stornoway Diamond Corporation (Stornoway) was established in 2003 resulting from to a plan of arrangement between Northern Empire Minerals Ltd. and Stornoway Ventures. In 2011, Stornoway acquired 100% interest of the Renard Mine. The construction of the Renard Mine began in 2014 and achieved full production in 2017 [1, 2]."

Jan 1, 2019

By L. H. Chen, Y. C. Chen, Leo Benyamin, W. C. Chen

"To investigate the evolution of fluid-driven fracture of rock-like material subjected to borehole fluid pressure and its consequential damage with regard to post-peak stabilization, micro-seismic activities have been monitored using nondestructive technique of acoustic emission (AE) corresponding to the macro-scale complete history of loading curve by setting the hollow cylindrical external circumferential strain to be a closed-loop feedback signal during servo-fluid-driven tests. Development of a novel fluidinduced loading system injected from internal borehole as well as monitoring system were equipped such that the initiation and propagation of micro-cracks enable to analyze experimentally. By programming/controlling either injection rate or fluid pressure, synthetic sandstones with low-permeability made by cement mortar were conducted in this study. It found that both the growth of macro-crack initialized intensively as reaching the breakdown pressure and the micro-seismic activities represented by AE locations show nice agreement. The experimental results in this paper provide better understandings of fluid-driven fracture mechanism.INTRODUCTIONFluid-driven fracture is a process of generating cracks by injecting viscous fluid into solid material. Conventionally, fluid-driven fracture tests have been performed by mining industry to measure the in situ stress (Haimson & Fairhurst, 1969) and fluid-driven fracture has been employed by the petroleum industry to recover oil and gas. Additionally, the mechanism of crack growth or the extension of existing cracks is important to the evolution of volcanic dikes over distances of a few kilometers (Lister & Kerr, 1991; Rubin, 1995), crack propagation in dams (Bolzon & Cocchetti, 2003) and the disposal of radioactive waste (Sun, 1969)."

Jan 1, 2015

By C. I. Walker

Field tests at a number of large mineral processing operations have been undertaken to better understand the wear life impact of different aspects of pump design, materials of construction and maintenance procedures. Data are presented for wear rates, and typical result variability is explored. To improve the availability of pumping equipment in a milling circuit it is not only important to improve the wear life, but also reduce the variability in the wear life of components so that the incidence of premature failure is lessened. Localised gouging wear due to flow separation and turbulent eddy formation is often the point at which part-holing occurs. A number of improvements to the design of pump impeller and throatbush (suction side liners) to reduce the localised gouging wear are outlined. Also, results are presented on the use of composite materials (mix of metal, rubber and ceramic) for throatbush materials to protect specific areas against wear.

Jan 1, 2012

By A. H. Duffield

"Forming part of the Prairie Evaporites, the sylvinite layer mined at Alwinsal underlies the Blairmore quicksands and the water-bearing Devonian formations. Production is achieved by a method of trackless, continuous mining of rooms, leaving pillars for natural support. The paper describes the development of the mine, and the equipment and organization employed in the operation and maintenance of the underground facilities."

Jan 1, 1972

By B. M. Das, F. Claridge, V. K. Garga

Coal, as well as a large part of other minerals in Canada, is produced by surface mining methods. This has resulted in short and long-term accumulation of waste rock in dumps. Two main problems arise from the flow of water through these dumps: stability of dumps and the impact on stream flows. In recent years, a number of mines have started placing waste rock in valleys for general disposal or far constructing mine access road ways. All these have created challenges in the following areas: effective design of dumps and flow-through dams; stability monitoring of the structures; environmental impacts downstream by way of increased amount of fines in suspension, sedimentation, and toxic substances; and long-term status of flow and flood. Similar situations also exist in many civil engineering structures. This paper discusses the status of rock drains and the immediate and future research needs.

Jan 1, 1990

By M. E. Holter

"Limestone-bearing strata are exposed in seven areas of Alberta, each situated adjacent to rail and road facilities. Six of these centers are located along the eastern edge of the Foothills and Front Ranges of the Rocky Mountains in western Alberta. The other is in northeastern Alberta, along the eastern margin of the Alberta Basin. High-grade limestones are present in Middle Cambrian, Upper Devonian and Mississippian strata. Middle Cambrian (Eldon Formation) limestones have been exploited only in the Exshaw area west of Calgary, where they formerly were used for lime production. Limestone beds of the Upper Devonian Palliser Formation are exploited at Exshaw and at Cadomin in west-central Alberta for the manufacture of cement. Reserves of high-grade limestone also are available in the Palliser Formation near Crowsnest Lake in southwestern Alberta and near BrUle, west of Edmonton. Upper Devonian limestones of the Waterways Formation are widespread in the Fort McMurray area of northeastern Alberta, but available data indicate they are of inferior quality to the limestone deposits of the Rocky Mountains regions. The Mississippian Livingstone Formation contains large reserves of high-grade limestone at several localities in the Rocky Mountains and Foothills. Commercial development of the unit is now underway at Crowsnest Lake and at Exshaw for lime production, and future exploitation of these beds is feasible at Blairmore and Nordegg."

Jan 1, 1973

By H. Kolcz, G. S. Dobby, R. Stratton-Crawley, S. W. Wilson

"The Matte Separation plant at Inco's Copper Cliff Smelter Complex is described. The continuing implementation of flotation column technology in the flowsheet in various applications is reviewed. Comparative studies on 0.038, 0.10, 1.1 and 1.8 m diameter columns have been carried out. It was demonstrated that consistent metallurgical performance was obtained with both pilot- and plant-scale units. Grade-recovery relationships for plant columns can be predicted with confidence from data obtained from test equipment. The work indicates further areas of the flowsheet in which columns present an attractive alternative to conventional cells. INCO’s MATTE SEPARATION PROCESSNickel concentrate from Inco’s Sudbury area mills has been processed in the Copper Cliff smelter for sixty years. Prior to that, Sudbury ores had been smelted directly. Historically, copper-nickel separation from smelter converter matte was achieved by the classical Orford process. In the mid-1940s Inco developed an improved separation scheme based on mineral processing methods, the Matte Separation Process. A generalized Copper Cliff Smelter Complex flowsheet is shown in Figure 1.Iron sulfide and gangue contained in the nickel concentrate are rejected in the smelting-converting process. The molten product, typically containing 50% Ni, 25% CU and 22% s, is cast at about 1000 ºC, into floor moulds and allowed to slowly cool for four days. During this period nickel sulfide (heazlewoodite, Ni,S,), copper sulfide (chalcocite, cu,S) and a copper-nickel metallic alloy precipitate and form a coarse grain structure that is amenable to separation by physical means. The phase chemistry of this system has been described previously by Sproule et al (1). This matte then becomes the feed to the Matte Separation Process.A simplified block flowsheet of the Matte Separation Process is shown in Figure 2. Matte ingots, typically weighing 20 tonnes each, are broken and crushed in a three stage crushing plant to approximately minus 0.01 m and conveyed to the Matte Separation building. Grinding is carried out in two parallel circuits each consisting of a rod and ball mill in series producing a flotation feed which is 65% minus 44 microns. Typical throughput of each grinding circuit is 650 tonnes/day. The metallic fraction of the feed is recovered by magnetic separation. This product, containing about 66% Ni and 15% CU, is a major component of the feed to the Copper Cliff Nickel Refinery."

Jan 1, 1990

By Pierre Sauvé, Guy Perrault, Armand Savoie, Pierre Trudel

"La Mine Doyon est une entreprise détenue à parts égales par Cambior Inc. et par Minerais Lac Ltée qui en est l'opérateur. Les statistiques de production au 1"" janvier 1990 indiquent que, depuis le début de son exploitation (1980), 10.3 Mt de minerai d'une teneur moyenne de 5,9 g Au/t ont été usinées. Les réserves sont estimées a 10,4 Mt à une teneur moyenne de 6,6 g Au/t jusqu' à une profondeur de-450m.Trois zones minéralisées sont présentement en exploitation. Ces zones sont caractérisées par la présence de veines de quartz-pyrite accompagnées localement de chalcopyrite. Les roches encaissantes sont les schistes a séricite (zone# 1), les roches volcaniclastiques de composition felsique (zone #2) et intermédiaire (zone #2, zone ouest) ainsi que les roches intrusives appartenant au pluton de Mooshla (zone ouest). Toutes ces roches ont subi un métamorphisme régional dont l'intensité correspond à la limite supérieure du facies schiste vert ( -425°C}.Les zones minéralisées sont situées à I' intérieur des zones de déformation et d'altération les plus intenses. L'étude des structures mineures nous indique que la région a subi plusieurs épisodes de déformation ductile a fragile qui sont antérieurs, contemporains et postérieurs al a minéralisation. L'analyse structurale indique également que la déformation majeure est associée à une importante phase de compression orientée N-S a NNE-SSW.L’ensemble des observations suggère que la minéralisation et I' altération associée sont de type épigénétique. La mise en place du minerai se serait effectuée à la fin de l'épisode principal de métamorphisme et de la déformation."

Jan 1, 1990

By A. M. Elmahdy, T. Hirajima, M. Farahat

"Separation of molybdenite from chalcopyrite is mainly achieved through flotation technique to raise their grades up to 25% to be extracted in smelters. However, molybdenite recovery and grade obtained from this process is not satisfactory in most cases due to the natural hydrophobicity of both minerals. The influence of conventional heat treatment on pure chalcopyrite and molybdenite minerals was investigated. X-ray diffraction, TG-DTA and XPS techniques were applied before and after heat treatment. The results showed phase changes for both minerals. Magnetic separation experiments of single and mixture of both minerals at several magnetic intensities were made. For single mineral experiments, 100% molybdenite recovery was obtained at all experimental conditions as non-magnetic fraction whereas ca. 100% chalcopyrite recovery was achieved under certain conditions. In case of 1:1 binary mixture, 87% and 83% molybdenum and copper recoveries, respectively, were obtained. The increase in chalcopyrite magnetic recovery is related to the formation of more magnetic phases as confirmed by characterization techniques.The objective of this study is to increase the magnetism of chalcopyrite to make its separation from molybdenite by magnetic separation possible and to understand the mechanism behind it. These results indicate that it may be possible to upgrade molybdenite ores using heat treatment followed by magnetic separation to the required grade by smelters which is difficult to attain by froth flotation and the other techniques."

Jan 1, 2016

By H. Warren Newcomen, Dennis C. Martin

"This paper describes the investigation of a large, progressive slope failure on the southeast wall of the east pit at Highmont Mine, British Columbia Geotechnical investigation s consisted of geological and structural mapping, assessment of blasthole drilling records, review of rock core information, slope movement monitoring and back analysis of various possible failure modes. Climate records and mining history were also assessed to determine their relationship to slope movement .Analysis of movement monitoring records and geotechnical information indicates that the failure is deep seated. The upper portion of the failure surf ace occurs along clay filled discontinuities. The lower portion of the failure surf ace appears to occur through the highly altered rock mass. High groundwater pressures and mining at the toe of the slope are documented to have had a major influence on stability at various times during the failure. Stability analyses results are presented and possible remedial measures are discussed.IntroductionHighmont Mine is located near Logan Lake in the Highland Valley approximately 50 km southwest of Karnloops, British Columbia (Fig. I). Mining of the porphyry copper and molydenum ore bodies began in 1980. In May, 1983, when mining in the east pit had progressed to a depth of about 60 m (200 feet) , a failure (designated the Southeast Failure) began to develop in the southeast corner of the east pit. Subsequent mining to a depth of 110m (360 feet) was accompanied by frequent and substantial slope movements involving between 500000 and I 000 000 m3 of rock . The slope was monitored extensively to assess short-term movement trends for operational safety. Geological mapping, core logging and rock mechanics testing were used in conjunction with the long-term monitoring information to determine the failure mechanism, conduct stability analyses, assess the effects of instability on pit design and enable design and installation of remedial measures."

Jan 1, 1988

By S. Broda

Waste rock piles (WRP) are made of heterogeneous, coarse grained waste rock, with inclined layers due to segregation along the slopes and haul traffic compacted layers, creating highly contrasted hydrogeological conditions. The internal structure of the pile has a major impact on water and oxygen movement and pore water pressure distribution. In the presence of reactive minerals, this influences the production of acid mine drainage (AMD) or contaminated neutral drainage (CND) with metal leaching from the WRP. Water flow and distribution may also affect slope stability, particularly following major infiltration events (rain/snow melts).The prediction and interpretation of water distribution in WRP is a challenging problem. Numerous numerical investigations of short and long term forecasts have been conducted, and many of these were found of limited reliability. The shortcomings of existing approaches are typically due to difficulties in representing preferential flow processes in macropores. Such phenomena are in fact often neglected in the assessment of water flow in WRP because these are unattainable with the classical porous media approach typically used in this field. This paper focuses on the use of modeling techniques originally designed for massive fractured rock media to simulate flow in WRP. Waste rock properties used in this study are retrieved from large scale laboratory permeability and water retention tests and from in situ infiltration tests. The effect of WRP configurations on water flow into potentially reactive zones is examined with the numerical 3D fully-integrated surface/subsurface, variably saturated flow model HydroGeoSphere. Material properties retrieved from the laboratory tests are represented by means of stochastic facies distribution generated within a probability framework. Modelled soil water contents and hydraulic head distributions, as well as fluxes within a simple waste rock pile, with compacted layers, are compared with results retrieved from simulations based on the classical equivalent porous medium approach. Results indicate significantly increased flow towards the looser waste rock zone by considering heterogeneous material distribution, causing weak or absent capillary barriers and preferential flow paths. Practical implications for the design of waste rock piles are also discussed.

Aug 1, 2013

By A. M. Cann, C. I. Godwin

"The Kemess porphyry copper-molybdenum deposit occurs in the Intermontane Belt of north-central British Columbia. The deposit is in andesitic to basaltic flows and tuffs which may be correlated with the Savage Mountain Formation of the Upper Triassic Takla Group. Most known chalcopyrite and molybdenite is associated closely with a 500-m-diameter zone of intense quartz-sericite-pyrite alteration. A zone of supergene enrichment, up to 30 m thick, underlies a leached capping about 20 m thick. The age of mineralization and the surrounding granodiorite and quartz monzonite pluton is Early Jurassic. K-Ar and Rb-Sr analyses indicate that the mineralization and alteration is slightly younger (l82±6 Ma) than the granitic intrusion (KAr: about 205±6 Ma; Rb-Sr: 190±4 Ma). The low 87Sr/J6Sr initial ratio for the granodiorite is typical of plutons in the Intermontane Belt.IntroductionKemess is a medium to small porphyry copper-molybdenum deposit with significant gold and silver values (Pilcher and McDougall, 1976). This paper describes the lithologies and alteration at this property; geochronology by Rb-Sr and K-Ar methods defines the ages of mineralization and surrounding plutons to be Early Jurassic.The property, located in the Thutade Lake area of northcentral British Columbia (NTS Map 94E; lat. 57°04'N; long. 126°44'W), is about 425 km northwest of Prince George (Fig. 1). Closest road access is 35 km southeast of Kemess. Final access must be by float plane or helicopter. The British Columbia Railway right of way passes 70 km to the southwest of theproperty.A prominent gossan zone at Kemess was staked in 1967 by Kennco Explorations (Western) Ltd. following detection of geochemical anomalies during stream sampling the previous year. During 1968, 1969and 1971, Kennco completed 232 m of X-ray diamond drilling, conducted geological mapping and carried out geochemical sampling of silts and soils (Stevenson, 1969; B.C. Ministry of Energy, Mines and Petroleum Resources, G.E .M., 1969 and 1971). Getty Mines Ltd. optioned Kemess in 1975and 1976. They remapped the area and diamond drilled 12 BQ and NQ holes, totalling 2065 m (B.C. Ministry of Energy, Mines and Petroleum Resources, Expl. B.C., 1975)."

Jan 1, 1980

By H. N. Tran, D. Barham

"A systematic survey of the appropriate literature in terms of phase equilibria and possible reactions involving deposits in Municipal Solid Waste (MSW) incinerators are analyzed particularly with respect to the theoretical first melting points of typical ashes and the possible presence of a liquid phase at the temperature of ash-metal interface. Conclusions are drawn on the basis of the possible presence or absence of various metal chlorides and sulphates in such situations, and their effects on the problems of fouling and metal corrosion. From preliminary results, it would appear that ZnCl2 is unlikely to be present in any molten phase which causes corrosion because it evaporates rapidly from such liquids. It would also appear that PbCl2 and, by inference, ZnCl2 will sulphate at relatively low temperatures if the flue gas contains SO2 and O2.IntroductionMunicipal Solid Waste (MSW) incinerators produce fly ash which deposits on heat transfer surfaces throughout the furnace, leading to corrosion and loss of energy recovery efficiency. Despite a massive amount of research carried out on the subject of corrosion in MSW incinerators, the problem of corrosion of heat transfer metal is still with us, and no definite over-all cause and effect relationship has yet been identified. In order to make a contribution to the eventual solution of this problem, the authors have examined the problem from the beginning, using their knowledge of fouling and corrosion problems in black liquor recovery boilers as a starting point.The incineration of MSW has been used for many years to reduce the volume of material sent to landfill (ash volume compared to raw waste volume), and, in most cases, to recover energy at the same time by raising steam The steam may be ""low- or high pressure/ temperature"" depending on its end use. The higher the steam pressure and temperature, the greater seem to be the problems with corrosion of heat exchanger metal, presumably because the metal must withstand higher surface temperatures.The chemical and physical composition of MSW is extremely variable, not only on a regional basis, seasonal basis, and day-today basis, but also on a minute-by-minute basis, due to the inhomogeneity of MSW. This makes it extremely difficult to define cause and effect relationships, because both cause and effect are transient in nature."

Jan 1, 1991

By M. J. Nicol, T. Moyo

Ammoniacal solutions are an effective lixiviant for the oxidative dissolution of some mineral sulphides. A detailed study of the anodic dissolution of chalcopyrite in ammonium sulphate-ammonium hydroxide solutions has been carried out using cyclic voltammetry, chrono-amperometry and rest potential measurements. The role of the copper(II)/copper(I) redox couple in the oxidation process has been evaluated. Rest potentials have been found not to be affected by oxygen but to increase with an increase in initial copper(II) concentration. Pseudo-steady-state anodic current densities measured in the absence of copper(II) ions at the rest potentials obtained in the presence of copper(II) ions increase with increasing concentration of copper(II) ions, confirming the positive effect of copper(II) ions on the rate of dissolution of the mineral. Cyclic voltametric and chrono-amperometric data show that in the absence of initial copper(II) ions, the rate of dissolution in the presence of dissolved oxygen is significantly lower. These results confirm that the effective oxidant for the mineral under the conditions of the study is copper(II) and not dissolved oxygen. Coulometric measurements have been used to establish the stoichiometry of the anodic reaction at different potentials.

Jan 1, 2014

By S. Khoshkhooei

In this research, the effects of rare earth elements addition on thermal fatigue behaviors of AZ91 alloy were studied. Repeated heating and cooling cycles were applied on the samples at 170°C and 210 °C to develop thermal fatigue cracks, Crack growth mechanisms and microstructural influences were investigated by optical and scanning electron microscopy (SEM) as well as energy dispersive X-ray spectroscopy (EDS), Thermal fatigue behaviors were improved successively by addition of up to 2-wt% RE, This improvement is attributed to consummation of the aluminum of the melt by precipitation of the needle shape Al 11 RE3 phases, This process reduces the volume of Mg17Al12 phases and consequently decreases the brittle Mg/Mg17Al12 interfaces which are the main reason of weak thermal properties of the alloy at rather high temperatures, Further additions of RE, however, reduced the thermal shock resistance of samples by increasing in the mean length of the brittle needle shape phases.

Jan 1, 2005

By A. Hayatdavoudi, D. Chitila, F. Boukadi

"Shale oil and gas have provided a tremendous boost to energy production in the United States even though the characteristics and behavior of shale are yet to be fully understood. Hydraulic fracturing is often applied to horizontal shale wells to stimulate production. This experiment seeks to determine effects of cyclic variable temperature, water vapor and exposure time on shale micro fracture propagation. We used 22 small Pierre shale specimens and subjected them to aforementioned conditions. Fractures developed in 19 specimens. Combination of high temperature and high water vapor generated the largest number of micro fractures on the specimen surfaces.INTRODUCTIONShale oil and gas have contributed immensely to energy independence in the United States. Most if not all shales depending on their total organic content (TOC) and their clay content bear the promise of being a source rock. For example, the Eagle Ford shale play, located in south Texas, is one of the key contributors to the recent rise in oil and gas production in the United States. Data from the U.S. Energy Information Administration (EIA), published in 2014, states that monthly oil production from Eagle Ford wells increased from 340 barrels per day (bbl/d) in January 2009 to nearly 1 million bbl/d in June 2013. Natural gas production has also increased at a similar rate over the same period, from 5.8 million cubic feet per day (MMcf/d) to nearly 4,000 MMcf/d (EIA, 2014).According to the railroad commission of Texas (RRC) 2014 published information, the Eagle Ford shale play is an important play because it produces gas and more oil than other shale plays in the United States. It is an organic-rich play with carbonate shale percentage in the 70% range in south Texas and the shale content increases moving to the northwest. High carbonate proportion renders this play brittle and suitable for hydraulic fracturing treatments."

Jan 1, 2015

By C. A. Roloff

Demands for increased grinding production, lower-grade are and limited capital have resulted in ever larger grinding mills, some as large as 36ft (/1 m) in diameter and 12,000 hp (8,950 kw). The result is often f ewer machines per plant, with a greater dependence on each machine. To meet these reliability requirements, manufacturers of mills, drives, castings and other components have had to be innovative and creative in their design. Only by thorough review of past designs and practices and by model studies confirmed in field tests can the manufacturer have full confidence in the product. Because of the great interest in large mills, a short review of larger machines is presented. This discussion covers material feeding, bearings, the rotating element, drive trains and material discharge.

Jan 1, 1979