Search Documents

By T. V. Nethery

Introduction A brief account of the East Malartic fire is essential if this paper is to serve the purpose implied by its title. The fire originated in the timbers of No. 4 shaft at the 10th, or 1,570-foot, level; this was the top or collar of the underground sinking operations. At the time, sinking was in progress and the shaft bottom was 242 feet below the 12th station horizon, or 618 feet 'below the l0th level. Above the l0th level, the shaft was not in use as the surface plant was not yet completed. The shaft crews descended from surface in No. 3 vertical shaft to the l0th level, where they transferred to No. 4 shaft, a distance of 1,450 feet. Of the sixteen shaftmen mucking at the shaft bottom, four were able to reach safety. One shaftman was overcome by fumes midway between the two shafts on the l0th level, while attempting his escape. The remaining eleven men climbed as far as the 11th station and there succumbed to carbon monoxide. No. 4 shaft, inclined at 61 degrees, bad been raised and timbered from the 10th level to surface; this bad been followed by sinking operations below the l0th. Two air hoists had been set up in the footwall of the shaft, 110 feet above the 10th level, and directly behind compartments No. 2 and No. 4. The waste from the shaft bottom was hoisted in 28-cubicfoot buckets on mono rails and dumped over standard shaft sinking doors into waste chutes built into No. 1 and No. 3 compartments. The five-compartment shaft, 7 ft. 8 in. by 34 ft. 6 in. overall size, was heavily timbered. In addition to the standard shaft timbers of 8 in. by 8 in. and 8 in. by 10 in. B.C. fir, the hanging-wall and ends of the shaft were laced with 4-inch spruce lagging. This represented approximately 300 board feet of timber in placee for every foot of shaft. The cause of the fire bas never been determined, despite every effort to do so. The inquest held for those who lost their lives in the fire was an extremely thorough one, but only the location of the origin, and not the cause, was established.

Jan 1, 1950

By S. V. Ulianov, A. Y. Senchenko, A. A. Shvets, A. V. Aksenov

Development of an efficient technology to process complex ores containing gold and antimony as well as silver is described in the paper. The results from the testwork aimed at the valuables recovery by means of flotation are presented. A process sample of antimonite gold-bearing ore was studied in TOMS institute aiming at development of a technology to process such an ore with generation of antimony concentrate and sulphide gold-containing concentrate. Material composition study indicated that the ore included 5.3% of sulphides: arsenopyrite – 2.4%, pyrite -2.4%, and antimonite – 0.5%. Gold is present as an isomorphic dissemination in arsenopyrite. At sighter testing stage a direct selective flotation flowsheet was chosen to process the ore. Antimonite flotation was activated due to addition of lead nitrate. A single cleaning of a rougher flotation concentrate resulted in antinomy concentrate with 30% Sb content and 71% recovery. Au recovery into antimony concentrate did not exceed 1%. Sb flotation tailings were used to float the remaining sulphides and gold. The resulted sulphide concentrate was characterized by Au content of 20 g/t at about 80% recovery, arsenic content - 10% at ~80% recovery, and sulphur content - 18% at ~81% recovery. The sulphide concentrate can be forwarded to further processing aiming at gold recovery. Given that the concentrate is highly refractory it should be pretreated (bacterial or pressure oxidation, Albion process) prior to cyanidation in order to liberate gold from sulphides. The proposed technology allows one to solve the problem of precious metals recovery from antimonite ores.

Jan 1, 2016

By M. Härting, D. T. Britton, M. Nzikou Mamboukou

"Copper containing different types of nanocomposites have been characterized for nanolabelling and ID. Three types of the rare earth nanoparticles were used for this study, the oxide and the sulphur compound of the Eu and Tb. Characterization techniques uses SEM, and Raman for morphology, chemical composition, and optical characterization respectively. It has been shown that it is possible to include the rare earth particle in a copper matrix without damaging its physical properties. INTRODUCTIONThe development of new materials, often involves the addition of new properties without changing the beneficial properties of the original material (Chen et al., 2009; Khana et al., 2007; Patil et al., 2008). Nanocomposites are nanostructured materials, whose structural elements including clusters, crystallites or molecules, of dimensions ranging between 1 to 100 nm (Moriarty, 2001), or a composite material where one of the phases is a one, two or three dimensionally nanostructured material (Nanotechnology, 2006; Wang, 2001). Nanocomposite materials research is a fast growing area due to the high demand for materials for specialized applications (Edelstein & Cammarata, 1998), such as biolabelling, magnetic storage media, solar energy transformation (Jisen et al., 2004), and resistance welding applications (Bessergenev et al., 1997; Kwon et al.,2006).The properties of the nanocomposite materials depend not only on the properties of their individual parent materials, but also on their morphology and the interfacial characteristics. Thus, significant efforts have been focused on the control of the nanoscale structures via innovative synthesis approaches. Therefore, novel materials of unique properties may be obtained by combining properties from the parent constituents into a single material (Balan, 2006; Garcia et al., 2009). Possible effects of nanocomposites in the original material may include changes in the mechanical properties such as hardness , wear resistance (Rafaja et al., 1987), and electrical properties (Britton et al., 2003). The inclusion process may therefore be used to tailor materials to have particular mechanical, electrical and optical properties (Das et al., 2009). However, to fully understand the nanocomposite, it is necessary to study the fundamental properties of both the host matrix and the inclusions (Li, 2008)."

Jan 1, 2012

By J. A. Vonhof, R. O. van Everdingen

Since 1949, a total of 59 disposal wells have been installed in Canada to inject liquid wastes from refineries, mining operations and chemical plants into subsurface formations at an ever-increasing rate. Well depths range from around 600 feet to almost 5,500 feet; injection rates range from 0.5 (U.S.) gpm to more than 1,000 gpm for individual wells; wellhead injection pressures range from a slight vacuum to over 500 psi. Apart from strictly technical considerations of well design, the geological, hydrodynamic and hydrochemical conditions at the disposal site have a strong bearing on the safety and success of such operations. Prevailing hydrogeological conditions in large portions of the country do not allow safe subsurface disposal.

Jan 1, 1973

By Nader Golchinfar

The V-shaped breakout zones around excavation boundary have been captured by a variety of numerical methods such as FEM and DEM methods and failure criteria such as linear Mohr-Coulomb and non-linear Hoek-Brown failure criteria. Diederichs (2007) used Hoek-Brown parameters in his spalling parameter approach; however, it is convenient to use the Mohr-Coulomb failure criterion in numerical modeling because the material parameters can easily be determined from triaxial tests. It is shown in this study that when peak and residual strength parameters as well as dilation angle are properly defined, the brittle Mohr-Coulomb failure criterion can be used to model depth of failure near underground excavations satisfactorily.

Jun 1, 2012

By R. D. Hossack

"The selection of a site for plant facilities is a function of several factors and has as its objective the maximization of profits, given fixed markets and sources of raw material locations. In practice there are several sites, any one of which or a combination of two or more would be suitable to meet the basic requirements of source of supply of raw material and labour and still fulfill market demands. The model used to select the optimum profit combination utilizes both computer programs and traditional financial analysis techniques. Of the three computer programs used in the mode), one is a linear program and another is a transportation simulator. Basic cost and price data are required. In examining costs, three levels are used: (a) distribution costs of raw material to the plant and finished goods to the market; (b) direct production costs at the plant, such as labour and locally supplied material; and (c) capital and overhead costs at the plant, such as construction costs, taxes, insurance, and federal and provincial cost allowances. The direct costs generally depend on the scale of operations, so that a large plant in one location may have a lower unit cost than two smaller plants. This, of course, must be balanced against distribution costs. In examining profit, it is necessary to think in terms of the price and volume of sales at each of the market locations. Given basic data and relationships, the model can be used to optimally locate production facilities or, alter-natively, optimally structure a transportation network given existing locations of plants and markets. It is dynamic to the extent that it can react to changes in volume, price and cost to optimally locate an additional plant, the expansion of existing plants, the shutting down or cutting back of plants, or the restructuring of distribution networks."

Jan 1, 1970

By S. J. Prout, J. M. Lang, D. Lascelles, K. Sarinas

"There is a growing demand for ore characterization methods to support metallurgical development programs from a true geometallurgical perspective. Today, there are multiple automated mineral analysis systems on the market, many of which are based on conventional mineral liberation data. However, liberation data can be limited when assessing the floatability of a mineral to predict its recovery as it doesn’t consider the surface area available for collector absorption and bubble attachment; whereas mineral exposure measurements can. Using the First-Order Rate equation to predict the recovery versus time of variously exposed particles, a model has been developed to predict the recovery of copper sulphides at a particular grind size. This model provides the opportunity for the prediction of copper recovery and grade from multiple, small-scale samples. These predicted values can be imported into resource modeling software, and guide the domaining of geometallurgical units within the ore body. Data has been analyzed from various global copper porphyry systems and compared with actual flotation testwork.IntroductionAs part of the development of a mining project, resource estimation primarily focuses on the definition of the quantity and grade of the ore in the deposit; as the project evolves from preliminary economic assessment through to feasibility, the geological model is usually further populated with hardness and recovery data.The CIM Definition Standards (2011) identifies measured mineral resource as the part of a mineral resource for which quantity, grade or quality, densities, shape, and physical characteristics are estimated with confidence sufficient to allow the application of “modifying factors” to support detailed mine planning and final evaluation of the economic viability of the deposit as an asset. The modifying factors include, but are not restricted to, mining, processing, metallurgical, infrastructure, economic, marketing, legal, environmental, social and governmental factors.With market fluctuations, many investors in the mining industry have become more and more risk averse which has increased the demand for more reliable data to support these modifying factors. This has led to the widespread use of geometallurgy and statistical analysis to better inform the resource estimation. Geometallurgy is used to characterize ore variability and is especially useful for highly variable or strongly zoned deposits, several close deposits that will be milled together, projects requiring complex or new metallurgical approaches, brownfields or sight-of-mine exploration, expansion projects that exploit new, deeper or adjacent reserves, and projects with significant legacy drill core that are being re-evaluated due to new economic circumstances."

Jan 1, 2018

By N. Dahata

Earlier research has indicated that an addition of titanium master alloy to aluminum alloys, results in improved fillability, grain refinement and finer pores. B206 alloy differs from other alloys used in automotive industry, with lower titanium level. This paper examines the effect of alloy chemistry (copper and titanium levels) and grain refinement (A1-5`)oTi- 1%B grain refiner) on grain size, microstructure and microporosity in B206 aluminum alloy. In this study, characterization of grain size, microstructure and microporosity was carried out using light optical microscopy (LOM) and scanning electron microscopy (SEM). Results have shown that the addition of 0.05 wt % titanium resulted in grain refinement of B206 alloy. With an increase in titanium to 0.25 wt further grain refinement, much reduced pore size and uniform distribution of pores resulted. These results suggest that B206 with proper addition of titanium has a promise as an alloy for automotive casting.

Jan 1, 2007

By W. Holdsworth

The flotation mill of Dentonia Mines, Limited, at Greenwood, B.C., went into operation on April 20th, 1934, and by October 11th a total of 15,000 tons of ore had been treated. It is intended in this paper to describe briefly the operation and to give some of the operating data which have been gathered. The metallic minerals in the Dentonia ore are pyrite, chalcopyrite, galena, and, occasionally, native gold, and the gangue includes chloritic material, vein quartz, and calcite. Pyrite makes up about 90 per cent of the metallic content of the ore, in which it is disseminated as irregular grains and well-formed cubes. An average analysis of the ore is: gold, 0.27 oz. per ton; silver, 1.73 oz. per ton; copper, 0.12 per cent; lead, 0.31 per cent; and zinc, trace. From the mine ore-bin, situated near the portal of the tunnel at the mine, the ore is hauled by motor truck to the mill, a distance of three-quarters of a mile, and there dumped into the receiving bin, which has a capacity of fifty tons. The hauling is done during one eight-hour shift, commencing at 7 a.m. The maximum size of the ore fed to the mill-bin is ten inches. Lumps larger than this are broken by sledge hammer to pass through grizzly bars, spaced ten inches apart, installed above the bin. The ore is drawn from the bin by a 30-inch, 6-ply conveyor belt, 18 feet 6 inches long. In the near future, when the cross-cut tunnel is completed, the ore will be trammed to the receiving bin. This will effect a considerable saving in cost. At the same time, the bin will be set back several feet, so that the length of the conveyor belt may be doubled. This will make efficient ore-sorting possible, and so ensure a minimum of waste rock in the mill feed.

Jan 1, 1935

By Keith Jones, Largo Albert

"Decelerometer testing of a rigid guide system in a mine shaft pro vides usefuI information to operating and maintenance people. High acceleration/deceleration rates can lead to high maintenance costs to bath conveyances and shaft and can also present an operating risk . Possible disastrous results in the shaft have been avoided by restricting the maximum conveyance speed until the shaft and/ or conveyance problems have been solved.The test instrument is a valuable aid especially during commissioning or updating of a hoisting installation. High acceleration/deceleration rates also lead to reduced hoist rope life. During the past fourteen years, a total of 15,000,000 feet of testing was performed in 74 assorted shaft compartments.Based on this experience, it is possible to establish acceptable conveyance maximum speeds provided that all other conditions in the shaft compartment are normal. The body of the paper will present examples of several tests made under actual operating conditions.IntroductionMore and more mine operators are recognizing the real value in the use of the decelerometer for determining the state of shaft guide alignment in their shaft compartments , not only during the initial mine start-up periods, but also on a regular basis while the mine is in production.Decelerometer testing, is a technique in which an accelerometer , commonly known as a decelerometer, is used for measuring conveyance acceleration/deceleration in a lateral plane. lts purpose is to determine the severity of shock loads produced by misaligned shaft guides. Testing is performed by mounting the instrument on the conveyance and operating the conveyance (empty and loaded) at various speeds up to and including full speed . However, full speed may not be attained due to conditions indicated by the tests. These conditions may present an operating risk to the plant."

Jan 1, 1984

Research on alternative lixiviants for gold is ongoing; however few people have looked at complete flowsheets. Alternative lixiviants are typically applied at concentrations 50 to 100 times those required for cyanidation. The higher concentrations make lixiviant recycle a vital part of the process. In addition it is no longer feasible to rely on lixiviant destruction to produce lixiviant free clean water for recycle to the comminution circuit. Ausenco has worked with Barrick to integrate reverse osmosis into the thiosulfate RIL processing flowsheet that forms the basis of the plant upgrade currently being constructed at Barrick’s Goldstrike autoclave facility.

Jan 1, 2014

By Cummings. J. B., R. Haworth

"THE OPERATION of the Potash Company of America, Ltd., at its plant near Saskatoon, Saskatchewan, is the result of many years of exploratory and development work, culminating in the construction of a shaft, milling, concentrating and other facilities necessary to the production of potash in a marketable form.The possibility that potash existed in •commercial quantities in Saskatchewan was first indicated in 1943, although it was not until mid-1946, when Bata Petroleums penetrated a potash bed at its Verbata No. 2 well near Unity that substantial in-ter.est was developed in the possible exploitation of this important mineral product.The Potash Company of America, which is the largest producer of pot-ash in the Carlsbad, New Mexico area, a district that has been sup-plying about 90 per cent of the North American potash demand, be-came interested in the Saskatchewan deposits •at an early stage. Its engineers made an intensive study of the western Saskatchewan area in 1947 and continued their review of operating problems throughout the next three years.""Potash"" is the commonly used general term applied to the minerals of potassium, of which there are several. The most common mineral forms in which it is produced are potassium chloride and potassium sulphate. The potash content of potassium compounds is ordinarily ex-pressed in terms of potassium oxide (K20) equivalent."

Jan 1, 1960

Barrick Gold Corporation is the gold industry leader, with 25 operating mines and a pipeline of large, long-life projects located across five continents, in addition to large land positions on some of the most prolific mineral districts. Barrick's high level of commitment to sustainable economic development and environmental stewardship was recognized by Dow Jones Sustainability Index (DJSI) - World, for the third consecutive year in 2010. The potential for adverse environmental effects from acid rock drainage (ARD) and metals leaching (ML) and their financial implications for Barrick are key considerations in our environmental assessment and business development processes. Barrick's membership in the International Network for Acid Prevention (INAP) reflects the importance of these issues to our business. INAP's development of the Global Acid Rock Drainage (GARD) Guide (a best practices guide for acid rock drainage prevention) provides Barrick with an important tool to assist in the assessment of environmental and financial risks from ARD and ML associated with our planned and ongoing mining operations (INAP, 2009). In this paper we will discuss how Barrick incorporates the GARDGuide and its principles for ARD and ML prediction and prevention in our business development processes and the management of our operations. The GARDGuide serves as a key reference for our project environmental assessments and as a common link between our projects and operations management, consulting specialists, permitting and regulatory authorities and the public. We will discuss how the GARDGuide is being "syndicated" throughout Barrick as a standard of practice and present a case study of how it was used in a recent Barrick Business Development Project.

Jan 1, 2011

By C. Harold Riches

This article is directed co a commentary on the patent system in its relation to the public interest. As man gained supremacy over his environment, he could devote progressively increasing portions o his time to improving his standards of living. In the history of the human race, we have advanced from the hollowed floating log to the modern steamship of the present age; from the sickle and flail to the reaper and combine; from the trumpet and drum as a means of communication co the telegraph, telephone, and radio; from the horse and ox cart to the automobile, truck, aeroplane, and train; and so on ad infinitum through the list of inventions on which are based the industrial and political economies and standards of living we enjoy today. It has also been a long road from the day of the alchemist and his closely guarded secrets to the era of the patent system and its storehouses of knowledge open to the world. The alchemist and the craft and merchant guilds closely guarded their secrets. In fact, they largely opposed innovations on the grounds that they might injure profits and restrict employment. In these days of unrest, with great clamour out of doors for radical changes in our political and industrial economies, it may not be untimely to examine one of the keystones which support the economic structure we know as the free enterprise system, the system which is predicated upon the right of the individual to own property. Many, through impractical idealism, ignorance, confused thinking, or blind political prejudice, advocate the substitution of ownership by the State ? for the right of ownership by the individual. As civilization has advanced to the high standards of living we enjoy today through the efforts of a comparatively few inventors, the patent system which has provided the incentive that created the inventions on which our industries and our employment are based is fully understood and appreciated by a comparatively small percentage of our people. As a result, the patent system, as a keystone in our free enterprise economy, is an apt target for destructive criticism, with the thought, possibly, that by eliminating or drastically restricting the several rights to individual ownership one by one, ownership by the State will progressively replace ownership by the individual.

Jan 1, 1949

By J. Hedderson, J. Starkey, S. Reeves, B. Hilscher

"As ore sorting becomes more common, it is important to quantify its impact on comminution circuits in order to precisely predict its effect on throughput, grind, and mill operating conditions. Since sulphides and other valuable minerals are often softer then the surrounding waste rock, the ore kept by a sorting system is typically softer than the average ore. In order to accurately forecast production, new measurements of hardness need to be performed on the new concentrated mill feed. This paper proposes a methodology to examine this effect quantitatively at an early stage of project development using the SAGDesign test.INTRODUCTION The application of ore sorting in the mining industry is one of the most promising recent technologies with the potential to cause step change in the way concentrators are designed. Most typically, ore sorters are used to sort a given ore flow for grade, either to reject waste from the mill feed, or rescue ore from the waste pile. Ore sorting technologies have been successfully applied at many mining properties in various forms and while the technology has reached or is reaching maturity in other industries, it is still in development in the mining sector. As a result, there is not yet a general consensus on the considerations that need to be made when designing a plant with ore sorting from a feasibility level above and beyond what is commonly performed as best practice. This paper will discuss those considerations and propose a methodology for integrating ore sorting into a comminution circuit at the design phase. Due to the linearly additive nature of the SAGDesign Test results, a “hardness balance” can be developed to estimate the ore hardness which would be measured in any sorting mass split using only two data points. This will allow a design engineer to make more informed decisions as to the most appropriate mass split to select in relation to the incurred operating costs and grinding circuit sizing."

Jan 1, 2019

By M. Djivre, T. Eger, A. Godwin, I. Bhattacherya

Load-haul-dump vehicles (LHDs) are extensively used in underground mining, however, equipment design and operating conditions contribute to restricted operator sight lines. The inability to clearly see people, objects, or hazards around the machine has contributed to a number of accidents including fatal injuries. In order to identify vehicle design characteristics resulting in restricted and blocked sightlines, line-of-sight assessments are traditionally completed in the field. However, field methods are unable to evaluate lineof- sight under dynamic operating conditions, and are limited in their ability to provide feedback on the impact of various operator characteristics such as sitting height. Results of this research show computer simulation and virtual reality can be successfully used to evaluate line-of-sight during the operation of LHD vehicles. In order to benefit from virtual reality applications, the work environment, LHD vehicle, and human posture need to be represented as accurately as possible. A computer simulation program with ergonomic analysis features, Classic JACK 3.1, was successfully used. Threedimensional CAD models of LHDs were developed from manufacturer specifications and pictures taken from LHDs currently in use. The LHD models were imported into the JACK environment, a digital human was positioned in the cab of the LHD vehicle, and the vehicle and human were driven over a typical mine route. Real-time feedback in the JACK program was used to identify what the operator could see under different operating conditions. Machine characteristics and operating scenarios resulting in impaired line-of-sight were successfully identified with this method. The JACK program could also provide real-time feedback on the human’s joint forces and torques, strength requirements, postural comfort, and metabolic energy expenditure. As a result, this method could be used to successfully evaluate musculoskeletal injury risk factors along with system design recommendations to improve workplace safety and productivity in any setting. The LHDs evaluated in the JACK software package can also be combined with mine models and imported into other VR software packages (e.g. Blender) in order to enable viewing in Laurentian University’s Virtual Reality Laboratory. The VR models using these packages can be viewed in stereo to provide better appreciation of spatial vision issues.

Jan 1, 2005

By S Sokhanvaran

Electrodeposition of silicon from a cryolite based electrolyte at a relatively low temperature (1000°C) is a promising approach to generate high purity silicon. In order to obtain fundamental data pertaining to electrowinning of silicon from Cryolite?SiO2 melts, density and electrical conductivity measurements were made. A range of temperatures and SiO2 contents was studied for each property. It was found that while density has an inverse relationship with temperature, the dependence for electrical conductivity is direct. Increasing silica content up to the saturation limit (~ 5 wt%) increases the density whereas further increase in SiO2, lowers the melt density. On the other hand, the conductivity is lower for the melts with greater SiO2 content, at any temperature.

Jan 1, 2011

By Zhan Zhang, Hiromi Nagaumi, Zhen Li

"Recently, the remarkable strengthening effect of ??-Al(Mn, Fe) Si dispersoids at both ambient temperature and elevated temperature were found by several researches. A large amount of dispersoids can be formed by applying special heat treatments and within a suitable range of chemical composition of AA3xxx alloys. In the present work, the influences of Cr addition on the mechanical properties and microstructures of the Al-Mn-Mg-Si alloys were investigated. The mechanical properties at ambient and elevated temperatures were evaluated by micro-hardness and yield strength. Moreover, the microstructures in as-cast and heat-treated conditions were quantitatively analyzed by optical and electron microscopes. Results revealed that Cr also had effect on the number density and volume fraction of dispersoids. Micro-hardness and yield strength at ambient temperature increased with the increasing content of Cr, and the Cr addition increased the yield strength at elevated temperature as well. Moreover, the creep resistance at 300°C improved dramatically with the increasing content of Cr.INTRODUCTION Traditionally, AA3xxx aluminum alloys were widely used in packaging, automobile and architecture industries, because of its good formability, excellent corrosion resistance and weldability. And AA3xxx alloys were considered as non-heat-treatable alloys. However, the strengthening effect of dispersoids in AA3xxx alloys was discovered recently (Li & Arnberg, 2003;Li, Muggerud, Olsen, & Furu, 2012; Li, Zhang, & Chen, 2016; Liu & Chen, 2015).Alarge amount of dispersoids could precipitate by a proper heat treatment.In order to further improve AA3xxxalloys, the composition of the alloys should be optimized. A few previous studies were reported to investigate the influence of compositions on AA3xxx alloys. Adding Mn element could enhance the precipitation of ??-Al(Mn, Fe)Si dispersoids and improve the yield strength(Muggerud, Mørtsell, Li, & Holmestad, 2013), as long as the concentration of Mn was under the solid solution limit. Fe decreased the solubility of Mn and accelerated the precipitation rate of ??-Al(Mn, Fe)Sidispersoids(Li & Arnberg, 2003), the yield strength and creep resistance at elevated temperature could increase with an optimized content of Fe(Liu & Chen, 2016). Mg element would affect the nucleation process of ??-Al(Mn, Fe)Sidispersoids by forming metastable Mg2Si(Hirasawa, 1975; Li, Zhang, & Chen, 2017a; Lodgaard & Ryum, 2000), metastable Mg2Si precipitated during heating process and promoted the precipitation of ??-Al(Mn, Fe)Sidispersoids, moreover, Mg provided solid solution strength for AA3004 alloys(Li et al., 2016). Si increased the volume fractionof ??-Al(Mn, Fe)Sidispersoids(Muggerud et al., 2013)and decreased the size of ??-Al(Mn, Fe)Sidispersoids(Li, Zhang, & Chen, 2017b). With the addition of Mo, the size of dispersoids became finer with a higher volume fraction, the volume percentage of dispersoid free zones was reduced. Elevated temperature yield strength and creep resistance improved due to Mo addition (Liu, Ma, & Chen, 2017).However, the effect of Crelements on microstructure and mechanical properties of AA3xxx alloys were rarely reported."

Jan 1, 2018

By R. H. Sheaphim

THE RECENT and continuing activity in the Boundary district, British Columbia, makes the publication of this paper timely. The following description and discussions are based on two years' experience in the district as Field Manager and Geologist for Attwood Copper Mines, Limited. The Attwood project was organized by Dr. D. F. Kidd to re-examine the Boundary mining camp. Thanks are due to Dr. Kidd, both for his intelligent guidance during the project and for his permission to publish this paper. Much of the data and many of the interpretations presented are credited to the work of, and to discussion with, Dr. W. H. White, Consultant Geologist, who worked for two field seasons on the project. However, the author assumes the responsibility for this presentation. Dr. C. D. A. Dahlstrom worked with the author during the latter stages of the project. His assistance and advice are gratefully acknowledged.

Jan 1, 1956

By Marketa D. Evans

The mining industry has a significant opportunity to capitalize on its past learnings in order to build better social relationships. The industry?s relationship with society is both critical and under pressure. Rising levels of public opposition and social conflict are already having material impacts on operations around the world. Industry has an opportunity to shape the future direction of this social engagement, build public trust and proactively respond to a material risk to operations, but first it needs to better understand the nature of the challenges and the urgency of addressing them.

Aug 1, 2013