Search Documents

By Robert A. Macinnes, Peter Moon, John P. Pappone

"This paper, in presenting the results of the application of the assessment centre method at Texasgulf Canada Ltd., illustrates a novel "" in-use"" technique for manpower training in the mining industry.IntroductionMining history is full of examples of what goes wrong when human judgment fails-disasters, floodings, loss of life and property. We must, therefore, assume the importance of selecting competent people for supervisory responsibility. This article de scribes a method for assessing supervisory ability, its first application in Canadian mining and the result s obtained over the past six years. It is known as the assessment centre method."

Jan 1, 1981

By M. H. Cullender

THE determination of the flow characteristics of gas wells depends upon the analysis of pressure data obtained under shut-in conditions and under one or more known flow conditions. These data are commonly referred to as back-pres-sure test data, and I know you are all familiar with the back-pressure equation where, Q rate of flow, Mcfd @ standard conditions C coefficient of the back-pres-sure curve P 1 formation pressure, psia P • sand face flowing pressure, psia P2 (psia)2/1000 n exponent of the back-pres-sure curve Figure 1 is a graphical presentation of the back-pressure equation; the coefficient is the rate of flow at a difference in squared pressures of 1, in this case 2250 Mcfd, and the exponent defines the manner in which the rate of flow changes with a change in the difference in squared pressures. In Figure 1, the exponent of the back-pressure curve is 0.554 which means that for a 10-fold change in the difference in squared pressures, there will be a 3.58-fold (10 raised to the 0.554 power) change in the rate of flow.

Jan 1, 1961

By J. B. Mitchell

Many of the pre-production and plant startup problems that we regard as inevitable are actually caused by poor organizational methods. Traditional methods of organization can be modified to provide clear definitions of responsibility, continuity and depth of involvement of key personnel in order to overcome these problems.

Jan 1, 1966

By D. A. Pirttinen

The promotion of improved coal quality for thermal generation can benefit our national economy. The construction of electric generating facilities in Canada is expanding at a rapid rate to satisfy the demands of a rising population and new uses for electrical energy. With remaining economic water power resources in the process of development, generation from thermal sources continues to grow. The increase in thermal capability has been somewhat arrested by a de-pressed economy, widening of inter-provincial and state transmission networks and decisions to exploit certain water resources before high capital investment is further in-creased by rising construction costs. The introduction of extra high volt-age transmission lines will further delay thermal generation planning, but in due course, when the effects of restrictive factors have been dissipated, steam-electric generation from fossil fuels will rise to considerable proportions. In time, nuclear sources will contribute a growing share to thermal power, but, it is doubtful if nuclear participation will ever displace conventional fuels for steam rising, unless it can be adapted to operate efficiently for variable outputs in peaking service. It appears certain that fossil fueled

Jan 1, 1961

By K. El-Ouassiti, M. Zouadi, C. Bazin, D. Hodouin

Data reconciliation techniques are used to attenuate the effect of measurement errors and estimate unmeasured variables. This paper illustrates the application of data reconciliation to hydrometallurgy processes using measurements from leaching and solvent extraction obtained from laboratory experiments. The application of data reconciliation provides an efficient way to detect gross and systematic errors and produces reliable performance indices for process evaluation.

Jan 1, 2005

By A. -M. Lafront

The corrosion resistance of die-cast and freely-solidified and electromagnetically-stirred thixocast AZ91D alloy has been studied using electrochemical noise technique in a 0.05M NaCI solution at pH 6.1 and 25°C. Specimens polished at different depths were immersed for a period of 75 min in order to assess the influence of the microstructure on corrosion kinetics and morphology. At depths between 10 and 50 µm (skin), all specimens showed general non-uniform corrosion with the lowest corrosion resistance. Between 100 and 200 µmn (interior skin), the observed corrosion was accompanied by superficial undefined pits due to metastable pitting. The corrosion form for 100-200 µm gave the best corrosion resistance. Stable pitting corrosion was observed beyond 400 µm deep on the bulk specimens. The skin of all thixocast specimens prepared billets showed a more corroded surface than that of die-cast. The interior skin as well as the bulk specimens showed better performance than that of the die-cast specimens.

Jan 1, 2007

"Block caving is the preferred underground mining method to profitably extract massive, low-grade orebodies; however, lack of cave access inhibits understanding the rockmass response to mining, which is needed for safer, more productive operations. Combining large datasets from multiple sources with virtual reality scientific visualization (VRSV) is an alternative method for understanding complex cave behaviour, by providing virtual access to the cave. A customized VRSV module was developed at UNSW Australia to investigate rockmass response to undercut developments at a case-study block caving operation. Time/sequence effects are investigated in rockmass response to blasting, which is an important factor in hard-rock mines.RÉSUMÉ La méthode d’extraction souterraine par blocs foudroyés est la méthode préférentielle pour extraire rentablement des gisements massifs à faible teneur. Toutefois, le manque d’accès à la chambre restreint la compréhension de la réponse de la masse rocheuse à l’exploitation, ce qui est nécessaire pour obtenir des opérations plus sécuritaires et plus productives. La combinaison de grands ensembles de données de multiples sources avec la visualisation scientifique par réalité virtuelle (VRSV) constitue un autre moyen de comprendre le comportement complexe de la chambre en fournissant un accès virtuel à la chambre. Un module de VRSV sur mesure a été développé à l’Université de Nouvelles-Galles du Sud (UNSW) en Australie afin d’étudier, dans une étude de cas d’une exploitation par blocs foudroyés, la réponse de la masse rocheuse aux développements de galeries de sous-cavage. Les effets de temps/séquence sont étudiés dans la réponse de la masse rocheuse au sautage, ce qui est un facteur important dans les mines de roches dures."

Jan 1, 2016

By Ralph J. Holmes, David McCallum, Alan Roberts, Rolando Orense, University of Auckland, Tobias Krull, Tom Honeyands, Kenneth Williams

"The safe ocean transport of bulk commodities like iron ore, coal, nickel ore, manganese ore and bauxite by large bulk ships is vitally dependent on the stability of the cargo under the influence of wave induced ship motion. Safety standards are set by such bodies as the International Maritime Organisation (IMO) with recommended tests for the assessment of bulk commodities. Since the 1960s, the bulk cargo code (BC Code) commenced defining methods to determine the Transportable Moisture Limit (TML) for transportation of bulk commodities. By the latter part of the 1960s, three TML test methods were defined, namely the Flow Table, Proctor-Fagerberg and Penetration tests. All three tests were predominantly aimed at determining TML values for mineral concentrates.More recently, bulk commodity producers, Maritime Organisations and Port Authorities worldwide have been investigating whether commodity based TML methods better reflect realistic safe ship transportation than the current concentrate based TML test methods. In these investigations, the relationship between the mineralogical and particulate parameters of specific commodities with respect to cargo stability and moisture retention has provided insights into the development of tailored TML test methods. To this end, an AMIRA International project (P1097) undertaken by CSIRO, TUNRA Bulk Solids, the University of Newcastle and the University of Auckland assisted the IMO Technical Working group to investigate the relationship between iron ore fines characteristics and a new TML test specific for iron ore fines bulk cargoes.A review of the three standard concentrate based TML methods and characterisation studies of iron ore fines, as well as cyclic triaxial testing to determine liquefaction resistance, resulted in the development of a modified Proctor-Fagerberg method for determining the TML of iron ore fines. Of particular importance in determining TML is mineral composition, porosity, particle density and allowing time for moisture equilibration."

Jan 1, 2016

By G. S. Hume

FOR MANY YEARS Canada lived in the hope of attaining a substantial production of petroleum and natural gas that, to geologists familiar with the sedimentary basins of this country, seemed an entirely reasonable expectation. There have been surges of exploration activity stimulated by oil and gas discoveries and development such as occurred in Turner Valley. However, it was not until the Leduc field in Alberta was found in 1947, and the significance of that discovery was realized, that the search became really intensive and continuons. Expansion now has become a matter-of-fact attitude based on results which would have been considered impossible of achievement a few years ago.

Jan 1, 1957

By C. Piribauer, E. Feichtenhofer, A. McEneaney

"As part of a major diversification project, RHI AG, through its plant in Drogheda Ireland, has developed a Caustic Calcined Magnesium Oxide (CCM) for use in the Cobalt (Co) & Nickel (Ni) hydrometallurgical extraction industry. In the course of the project, the company investigated the chemical and physical properties of a number of different Magnesia’s used in Co & Ni hydrometallurgy applications and has been able to determine the important parameters for a successful Magnesia for this application. A number of live plant trials have confirmed the results of this testwork and the company is now proceeding to produce this product in commercial quantities at Premier Periclase Ltd., the RHI AG plant in Drogheda, Ireland. This paper will outline the development work conducted by the company and highlight the important chemical and physical properties that make a successful CCM. Much of the research was conducted at the RHI Technology Centre in Leoben, Austria. In addition, a number of external laboratory studies were conducted on behalf of RHI AG. The result of this work has allowed the company to develop a Magnesia product with optimised properties for use in the Cobalt and Nickel hydrometallurgical extraction process.INTRODUCTION Premier Periclase is part of RHI AG, a globally operating supplier of refractory products, systems and services, headquartered in Vienna, Austria. The company produces Magnesia from seawater at its plant in Drogheda, Ireland. While the main focus is on production of refractory grade Dead Burned Magnesia for the steel industry, the plant also produces a number of different grades of Caustic Calcined Magnesia as well as Magnesium Hydroxide products. As part of a major project to diversify the company’s product base, the use of CCM in the Cobalt (Co) & Nickel (Ni) hydrometallurgical extraction industry was investigated. One of the company’s highly reactive grades of Caustic Calcined Magnesia was found to be particularly suitable for this application. In an effort to understand what makes a successful Magnesia for hydrometallurgy the chemical and physical properties of different Magnesia’s used in Co & Ni hydrometallurgy were investigated. This paper and conference presentation outlines the findings of this process."

Jan 1, 2017

By M. J. Merwin

Heat treated seamless tubular products are processed in a fashion that can be easily modified to produce dual phase microstructures, through the implementation of intercritical soaking prior to quenching. Dual phase steels are known to possess low yield strength compared to tensile strength. The steel line pipe market is interested in low yield-tensile ratio materials for application in reel barge pipe laying operations. In the current work compositions of commercially produced material already in use for the line pipe market were examined and dual phase microstructures were successfully developed. The microstructure and properties of the materials were found to be stable over the range of intercritical temperatures employed. Tempering temperature and, somewhat unexpectedly, small chemistry differences were found to have the largest influence on properties. Excellent toughness performance was observed in samples tempered at temperatures in excess of 550°C. Tempering in this temperature regime produced materials with strength suitable for application as API X60 line pipe. A difference in tensile strength between steels of similar chemistry was observed, and is not fully understood at this time. Welding performance was considered through simulation of three regions of the heat-affected zone. Neither intercritical temperature, nor tempering temperature, were found to have a significant influence on the heat-affected zone properties. The peak temperature achieved in the thermal cycle was the only significant factor. The hardness of the heat-affected zone was found to increase continuously with increasing peak temperature. While toughness was found to be low for both partially-transformed and coarse-grain heat-affected zones, the toughness of the fine-grained heat-affected zone was substantially better. Based on the results found in this laboratory study, a limited production trial is expected.

Jan 1, 2005

By J. S. Kirkaldy, W. J. Slater, G. R. Mason

Activation analysis for copper and manganese in 10 mg samples machined from aluminum-base diffusion couples has been used in the study of ternary diffusion in the Al-Cu-Mn system. The accuracy, economy and convenience of the method are considered to be very competitive with other methods for analysis of such small samples. Neutron-activated aluminum-zinc alloys in the range from 10 per cent to 100 per cent zinc have been equilibrated with a known volume and the vapors subsequently condensed and collected. The vapor pressures relative to pure zinc (the thermodynamic activities) have been determined at 550°C' by recording the relative count of /'-rays from zn65 in the collected samples. The method is a sensitive one, although subject to serious obstacles to experimental accuracy.

Jan 1, 1961

By R. A. Campbell, R. R. Rogers

"AbstractThe experiments described show that crude bismuth metal containing up to 5 per •cent lead, 0.14 per cent silver, 0.015 per cent copper, 0.02 per cent iron, .and small amounts of antimony, nickel, and tin may be refined to a bismuth content of 99.98 per cent by distillation followed by chlorination. It also is shown that bismuth trichloride of high ,purity may be produced by passing chlorine over hot •crude bismuth metal and allowing the resulting vapours to •condense in a cooler .part of the system.IntroductionBISMUTH is used in the production of alloys and pharmaceuticals. During 1952, the New York price for the refined metal was $2.25 per pound in ton lots.Some months-ago a Canadian producer requested the Mines Branch to investigate methods of refining the bismuth which they had been producing. Their crude product had been selling for $1.50 to $1.70 per pound and it was desired to increase its purity to at least 99.98 per cent so that it could be sold for $2.25 per pound."

Jan 1, 1955

By M. Zanini, D. Wong

ABSTRACT: Metals market improvements in 2005 drove the desire to increase nickel throughput and the production of nickel oxide sinter at the Vale Ltd. Copper Cliff smelter. Significant difficulties were encountered due to the unreliable quality of Bessemer matte being produced. Concentrate feed changes and the loss of technical and operational expertise during the previous market downturn contributed to the challenge of making the required improvements. Significant progress has been made in the converter aisle by focusing on employee engagement and standardizing best operating practices for a new generation of skimmers. This paper documents these initiatives and seeks to balance the art and science of converting.

Jan 1, 2012

By John J. Barakso

A summary of geochemical dispersion processes is presented. Secondary and tertiary dispersion of uranium was examined at several uranium prospects in British Columbia. The vertical migration of uranium from bedrock (primary dispersion) through overburden into the various soil horizons, and into snow and plants, was studied, and relationships were sought to explain the dispersion patterns in the secondary and tertiary environments. Soil developments were examined to obtain information on factors affecting the dispersion of uranium in soil profiles and tertiary substances; samples were analyzed for a number of elements. Biogeochemical data indicate that plant geochemistry is a possible exploration aid in areas of heavy overburden owing to the high selectivity of certain plants for specific elements. Some new data on the geochemistry of snow are discussed as a matter of research interest in the tertiary dispersion of uranium. Analytical techniques and problems are discussed, particularly extraction techniques, which must be carefully chosen to give reliable information on uranium dispersion.

Jan 1, 1979

By H. Vendette, N. R. Dando, A. Moras

The thorough analysis of results obtained from different testing campaigns performed on an alumina dry-scrubber pilot installation treating aluminum potline offgases, suggests a clear relationship between the emissions of gaseous fluoride and the fluoride saturation level of the alumina. The integration of this relationship into the development of a new generation of alumina dry scrubber represents an intriguing challenge regarding the design of more efficient air pollution control equipment. An innovative scheme challenging conventional industry practices was proposed. From theoretical simulations, the reduction in fluoride emissions can potentially be reduced by as much as 50% in the summer season. To validate this innovative approach, Solios in partnership with Alcoa Primary Metals, modified one of the Aluminerie de Deschambault's systems by adding new temporary equipment on the operating units and subjecting it to several test campaigns. This article presents the first results obtained in testing this new and innovative approach on alumina dry scrubbers used to capture fluoride emissions coming from aluminum electrolysis potlines.

Jan 1, 2006

By F. R. Erick Mulder

"AbstractTwo bottom-hole samples have been taken from two new completions in the Turner Valley field, Royalite Lowery No. 8 on the west flank and Royalite No. 73, which was deepened into a lower fault block, on the northeast flank. From the bottom-hole oil of Royalite Lowary No. 8 a synthetic sample was prepared to simulate the original fluid in the reservoir, saturated at the gas-oil contact conditions. The sample from Royalite Lewery No. 8 has been shown to be the original fluid present at this well and represents the oil phase near the oil-water contact in• the reservoir. Complete chemical analysis, P.V.T., and viscosity data have been obtained on these reservoir fluids, which represent the range of saturation from the gas-oil to the oil-water contact in the Turner Valley oil structures. Sampling techniques and the application of the analytical data to reservoir conditions and field operations are discussed. Super-compressibility curves for an average separator tail gas have also been prepared. These data have not been available before. They will be of fundamental value in futu.re reservoir engineering studies of this field and will also serve as a guide in determining operating practices."

Jan 1, 1950

By Ainul Akhtar, Steve Cockcroft, Jixiang Xu, Daan Maijer, Lu Yao

"Nitrogen rich Ti-N inclusions are one of the more difficult inclusions to remove during liquid metal refining of titanium. If present in the final component, they can significantly decrease the mechanical performance of titanium and its alloys in applications involving cyclic loading. Understanding the kinetics of dissolution of Ti-N particles during consolidation/melting of titanium can help us better operate and design the melting processes to minimize their occurrence in Premium Quality Titanium production. A numerical model based on finite difference method has been developed to calculate the dissolution of a spherical Ti-N particles in molten titanium. Analytical solutions were used to verify the finite difference code for calculation of concentration profile and the dissolution of spherical solids. Taking into account the limitations in these approaches for the different cases examined, the invariant field approximation showed good agreement with the results from the numerical analysis. Evolution of the size of a spherical Ti-N particle during dissolution was predicted by the numerical model and the particle dissolves in 163 s.INTRODUCTION Properties like low density, high specific strength and excellent corrosion resistance make titanium attractive for a variety of applications. Key characteristics in the processing of titanium and its alloys include its high sensitivity to impurities, especially atmospheric oxygen and nitrogen and its high reactivity in the molten state. Nitrogen rich inclusions Ti-N, also known as Type ? or hard alpha defects, usually have substantially higher hardness and lower ductility than the surrounding material. Because they can act as fatigue initiation sites, Ti-N inclusions can significantly decrease the mechanical performance of titanium and its alloys in applications involving cyclic loading, even in minor amounts (tenth of a percent) (Lampman, 1990; Moiseyev, 2005; Lütjering & Williams, 2007). Ti-N encompasses as a broad range of nitrogen contents from a few wt% up to stoichiometric TiN. The liquidus temperature of Ti-N titanium increases substantially with increasing nitrogen content. Consequently, depending on the concentration of nitrogen, the melting point of Ti-N inclusions can be above bulk liquid metal temperatures during melt processing. Thus, removal of Ti-N defects hinges on dissolution and not melting."

Jan 1, 2017

By A. J. R. Smith

"CANADA'S ECONOMY TODAY is about two-fifths larger than it was six years ago, as measured by the total volume of production of goods and services. Such an achievement has been a rare phenomenon in Canada's first one hundred years. Excluding the forced-draft expansions which took place under war-time conditions, perhaps only the first decade of this century recorded a performance of greater dimensions, when, with massive immigration, the opening up of the West and a powerful array of well-de-signed development policies, the country was looking forward confidently to a great future of nation-building in the twentieth century.What makes Canada's over-all economic advance since 1961 all the more remarkable is that six years ago there was virtually no one in this country who anticipated an expansion of such dimensions. Back in the buoyant conditions of 1956-57, perhaps such an achievement would not have seemed beyond our grasp. After 1957, however, Canada stumbled through an extended period of slow economic growth, high unemployment and substantial and widespread under-utilization of its productive capacity. By the early 1960's, conditioned by the emergence of substantial, persistent and pervasive slack in the economy, t h e r e were few Canadians bold enough to anticipate that their economy was about to embark on a Great Expansion. However, this •is, in fact, what occurred. Beginning early in 1961, Canada moved forward into a sweeping advance which grew into the longest and largest peacetime business expansion in Canada's first century as a nation -a truly great expansion by any standard of measurement. This strong thrust has moved Canada into the front ranks of over-all economic expansion among the industrially advanced nations in the 1960's."

Jan 1, 1970

By G Anders

Underground tests of slusher cables at first might seem to be quite simple and inexpensive. They do, however, take a long time and give results that may be ambiguous and unreliable. Also, because underground test conditions are not exactly duplicable, tests carried out at different times or in different mines could not be compared. An attempt was made to develop a laboratory test method that would provide for all factors affecting slusher cable performance underground in such a way as to make it possible to achieve comparable results from different series of tests by exactly duplicating test conditions. Such a method should also make it possible to vary individual factors systematically in order to give a proper assessment of the effect of changing conditions on cable performance. A set of tests, comparing the same two types of cable both underground and in the laboratory, is described. AN assignment at the Algom Nordic mine called for the comparison of two types of %-in. slusher

Jan 1, 1964