Search Documents

By S. Shairp

The first commercial application of the Dynatec two-stage zinc pressure leach process commenced operation at the metallurgical complex of Hudson Bay Mining and Smelting Co., Limited in Flin Flon, Manitoba in 1993. A key feature of the successful leaching operation is the presence of iron in solution, which facilitates oxygen transfer in the autoclaves and enables rapid oxidation of zinc sulphide minerals. At the same time, the solution from which zinc is recovered must be essentially iron free. Precipitation of iron from the solution starts in the autoclaves and is completed in subsequent atmospheric purification steps. Conveniently, these iron precipitation steps also remove nuisance elements such as arsenic and fluoride from the solution, while producing solids with good liquid-solid separation characteristics. This paper provides an overview of the current operations in Flin Flon, with particular reference to the behaviour and deportment of iron throughout the zinc plant.

Jan 1, 2006

By P. Fossi

This report describes a pilot-scale study of a hydrometallurgical process to treat high-grade nickel matte or a nickel-cobalt sulphide precipitate to produce high-purity electrolytic nickel. The first step of the process is the oxidative leaching of the nickel-bearing material by nitric acid; the nitrous gases generated during leaching are reconverted to nitric acid. The crude nickel sulphate nitrate solution is purified and is then subjected to a denitrification step. Nitrate separation is effected either by the crystallization of nickel sulphate or by precipitation of basic nickel carbonate. The electrolyte is prepared from the nitrate-free material and nickel is then recovered by electrolysis of the sulphate solution using insoluble anodes. Some technical and economic problems encountered with this processing route are discussed and the method is compared to the "all-chloride" process developed by Société Le Nickel.

Jan 1, 1977

By A. I. A. Salama

The CANMET Western Research Centre (CWRC) has developed a hydrocyclone model simulation of dewatering and fine particle separation circuits. The simulation is based on an existing empirical model. Utilizing a cyclone manufacturer’s published data, some modifications have been developed and integrated into the model. Feed stream characteristics, cyclone mechanical dimensions, and operating conditions are used in the CWRC modelling simulation. The computer results are presented in 3D graphs and corresponding 2D maps showing the cyclone mass recovery, percent solids by mass in underflow and overflow, and cut size as functions of the cyclone apex diameter and cyclone throughput (i.e., inlet pressure or pressure drop). Results of the computer simulation have been used in the economic feasibility and design of several dewatering circuits in oil sand plants.

Jan 1, 2003

By Erwin L. Zodrow

THE AUTHORS welcome this timely opportunity to comment o n a paper by MacLean and Merner (" Room-and- Pillar Mining at the Prince Mine of the Cape Breton Development Corporation " , ClM Bulletin , June 1978, pp. 59-62) concerning the rock falls and their relation to "a change in the strata". First, however, it is proper to express our gratitude to the Cape Breton Development Corporation, and in particular to A. R. MacLean, for making it possible for us at the College of Cape Breton to start two new collections. The first of these is a fossil plant reference collection from the Sydney Coalfield, Cape Breton (Upper Carboniferous period) , and the second is a documentation of the role o f pyrite in the formation of hydrated sulphates (samples from No. 26 Colliery, 1-B Mine, and the Prince Mine at Point Aconi). Conditions of sedimentation in the deltaic-type basin of the Upper Carboniferous time in the Point Aconi area were such that on the (coal) swamp, now represented by the Stubbart (or Hub) seam , (a) clays of varying thickness and extent were deposited , (b) biogenetic sulphur was introduced and (c) flora were buried. These are essentially the culprit s that make rock falls possible and at the same time predictable over large areas (in the present mine). The clays lithified to become shale, and biogenetic sulphur combined with iron to become pyrite (marcasite?), which exists as nodules and in fine-grained layers.

Jan 1, 1978

By R. J. Mitchell

"A lest apparatus has been developed for obtaining the relations among confining stress, porosity and percolation rate for hydraulic sand backfills. The apparatus can also be used to evaluate internal drainage characteristics and the effects of partial saturation on percolation rates. The test apparatus, test procedures and typical test data are presented in this paper.IntroductionAlthough the standard percolation test has become an accepted method of evaluating the drainage characteristics of hydraulically placed tailings backfill, it is recognized that the test results require considerable interpretation due to the following factors: (I) The results can be markedly influenced by varying sample preparation procedures, which vary the amount of material segregation in the sample . In particular, a thin layer of slimes on the top of a sample can control the flow of water into the sample. Wall edge effects can also affect the test results. (2) The in-place porosity of the backfill is not duplicated in the test sample and empirical formulae must be used to estimate the variation of percolation rate with porosity. (3) Internal drainage characteristics and the percolation rate of partly saturated fill cannot be evaluated in the standard percolation test.In addition to eliminating these problems, the compression percolation test apparatus also provides additional data on the mechanical properties of the backfill. Compressibility (or bulk modulus) is measured at different stress levels during the course of a test and this information can be used in evaluating the usefulness of the fill in providing ground control and in limiting ground subsidence. The engineering design of mine backfill is becoming an important part of the over all design of underground mine operations. The design problems are sufficently different from conventional civil engineering soil mechanics problems that new test methods and design procedures are required."

Jan 1, 1981

By Marie-Eve Boucher

The slag in iron ore pellets allows wet sintering during firing and leads to suitable bounding. The process of slag formation differs whether it takes place in the core or in the external zone of a pellet. In the core, hematite can be reduced to secondary hematite, depending on the temperature and on the carbon monoxide/dioxide partial pressure ratio. The reaction rim that appears at the outskirts of a silica particle in contact with the FeO bearing magnetite is considered as the slag precursor in the core of the pellet. By contrast, in the external zone of a pellet, where O2 is available and CO partial pressure is very low, the first step towards slag formation is flux decomposition, mainly dolomite and limestone. The CaO liberated through this reaction will be available to react with hematite by solid diffusion to form calcioferrites, which play an active part in the slag evolution process. These two slag formation paths will be explained.

May 1, 2007

By A. Lloyd, Montgomery, J. Jorgesen, W. J.

"Coals are ranked according to their degree of metamorphism or progressive change in the natural series from lignite to anthracite. The reader is referred to ASTM Standard D-388, ""Standard Classification of Coals by Rank"" for a detailed description of the system in use throughout North America including Canada.Fixed carbon and calorific value (expressed in Btu/ lb) calculated to the mineral-matter-free basis have been chosen as the main characteristics from which rank is established. Higher rank coals are classified according to fixed carbon content, lower rank coals according to the calorific value on a ""moist"" mineral-matter-free basis. Certain adjacent groups are differentiated according to their agglomerating (caking) properties. ""Moist"" refers to inherent moisture. Referring to Table 1, coals having calorific values greater than 14,000 Btu/lb on a moist mineral-matter-free basis and fixed carbon of 69% or more on a dry mineral-matter-free basis are classified according to fixed carbon. Coals having calorific values of less than 14,000 Btu/lb on a moist mineralmatter-free basis are classified according to calorific value on a moist mineral-matter-free basis. Agglomerating coals having 69 to 86% fixed carbon on the dry mineral-matter-free basis are classified in the low or medium volatile group of the bituminous class according to their volatile matter content. Agglomerating coals having calorific values between 10,500 and 11,500 Btu/lb are classified in the high volatile C bituminous coal group; nonagglomerating coals in the same calorific value range are classified in the sub-bituminous A coal group."

Jan 1, 1985

By Rhual L. Guerguerian

MINING has been practised by mankind for over sixty centuries (1). In 1876, the "ball mill" was patented, and during the century that followed rotary grinding developed to the state where individual machines are treating tens of thousands of tons of ore per day. This paper gives a brief description of design practices prior to the availability of advanced facilities, followed by modern analytical design development at Dominion over the past ten years.

Jan 1, 1978

By G. Shaw

IN recent years, most of the reconnaissance work of the Geological Survey of Canada has been mapped on a scale of 1 inch to 4 miles. Topographic base maps, commonly made from aerial photographs, were available to the geologist for such work. The advent of war curtailed aerial photography for civilian purposes, and by 1941 all areas already photographed had been geologically mapped. Nevertheless, the need for geological maps to assist post-war prospecting was so apparent, and the country to be covered is so vast, that some new method of rapid mapping had to be devised. It was felt that the need would be met if geological maps could be produced at a scale of 1 inch to 8 miles, provided they were sufficiently accurate in topographic detail to serve as guides to travel. Though in such maps there would be considerable sacrifice of geological detail, they would serve to outline, at least approximately, the major geological units, some of which might prove of sufficient interest to warrant later detailed study. It seemed that such mapping would be particularly useful in the northern regions of Canada which the work of early explorers has indicated are underlain largely by granitic rocks. These, so far as is known, are barren of mineral deposits, but within them are known to be areas or bands of 'greenstones' of the type that, in some localities, have been found to contain valuable orebodies. The problem, then, was to devise a method of mapping, particularly of such greenstone bands, that would make it possible to cover a relatively large area-say 30,000 square miles-in one season and at a cost below that of 4-mile mapping, with, of course, some sacrifice of accuracy. The problem seemed to be threefold: (a) to observe as much of the bed-rock as possible; (b) to produce a topographical map of as much of the area as possible, with particular reference to portions of geological interest; and (c) to cover as large an area as possible in a limited time, which meant faster modes of travel than have hitherto been used. The obvious answer to all three phases of the problem was the use of aircraft. If rock types could be broadly differentiated from the air, reconnaissance traverses by air would supply the answer to the first part of the problem. For topography, air photographs taken on reconnaissance flights appeared to be the answer. For the third phase of the problem, the use of aircraft was ideal.

Jan 1, 1943

By Yongbao Zhu

The Ag2O-mediated reactions of cycloaurated compounds with a general formula Au(L)Cl2 (L = bi-dentate C?N ligand) with thiosalicylic acid, N-acetyl cysteine or 1,2-benzenedithiol in DMF proceeds via ligand substitution of the Au?Cl bonds to afford the S-O and S?S adducts all in good yields. The reactivity of the dichloro, S-O and S-S adducts towards thiols were examined by reacting with cysteine in an aqueous medium, revealing that all of Au-Cl, Au-O and Au-N are labile for thiol displacement. The measurement of the inhibitive activities of these compounds against human cathepsins B and K showed that the dichloro and S-O adducts are effective inhibitors with IC50 values ranging from 0.1 to 2.6 -M, and that the S-S adducts are inactive.

Oct 1, 2003

By Egbert Burchardt

The challenge of "ore bodies getting steadily harder and lower in grade" was brought to light during the first oil crisis in the 70's. Shortly afterwards, HPGRs appeared on the scene with the promise of saving energy. This combined with developments in wear protection for the rolls ushered in a period of trade-off studies that considered the HPGR as an option to improve project economics or to even make projects feasible at all. Since then, applications of HPGRs at Cerro Verde (Freeport), PTFI Grasberg (Freeport), Mogalakwena (Anglo Platinum), Tarkwa (Goldfields), Boddington (Newmont), Penasquito (Goldcorp), and others have contributed to the creation of a formidable basket of operating experience. Collected through years of successful operation, this information has been used to validate design criteria, scale-up factors and establishing a clearer picture of what "to do" and what "not to do". This paper compares results from various mining operations using HPGRs in their processing plants. Some of the lessons learnt in different operating environments are reviewed in order to support proper implementation and operation of HPGR's. Some of the development programs that have been initiated to improve wear life of the tyres and to reduce overall operating costs are reviewed. It is timely to summarize today?s experience and analyse its implications for existing and new operations.

Jan 1, 2012

By G. A. Gross

"The Soviet Union has enormous reserves of iron ore in many different kinds of deposits that are widely distributed in this vast land area. The present iron ore industry is based mainly on deposits in Precambrian cherty iron-formation at Krivoy Rog, Kursk and Murmansk. Extensive reserves of both naturally enriched hematite ore and magnetite iron-formation in these areas alone could sup-ply all the domestic ore required for several hundred years.Many contact metasomatic magnetite deposits discovery in recent years in the eastern Ural Mountain belt and east of the Kusnetsov basin in Siberia are being developed, with ore reserves measured in billions of tons. Oolitic limonite-chamosite-siderite ores of Cretaceous and younger age at Kerch on the Black Sea and around the east and southern perimeter of the West Siberian basin constitute some of the largest concentrations of iron in the world. These sedimentary ores are low grade, of poor quality and difficult to beneficiate. Banded jasper magnetite and hematite iron-formation in volcanic rocks of Devonian age in Kazakhstan and along the Mongolian border are of special geoloica1 significance.Iron deposits in the Krivoy Rog and Kursk areas were examined and a large number of geologists discussed their work on deposits in many other parts of the Soviet Union during the writer's seven-week study tour of mines and research institutes in Moscow, Leningrad, Novosibirsk in Siberia and Kiev in the Ukraine. The descriptive geology of iron deposits of useable ore and of marginal material has been well documented in the course of systematic work and a large number of scientists are studying fundamental problems on the origin and treatment of iron ore."

Jan 1, 1967

By Pedram Sahba

In today?s emerging economy, pooling resources is a growing trend to reduce overall system costs. Two important resources of every maintenance department are repair shops and spare parts. In this work, we consider a system consisting of mine drills at multiple areas in a mine. In each area, a number of identical drills are operational. When a failure occurs, the defective component should be repaired in a designated repair shop. The failed component can be replaced immediately if a spare part is available. Otherwise, the drill is down until a component is repaired and put back into service. In this paper, the effect of pooling resources is examined, and the conditions under which it is beneficial to pool the resources are investigated. In addition, determining the optimal number of stand-by units, equipment or spare parts, in each case is of interest.

May 1, 2013

By S. Hill

For a mining operation, the determination of the best place to build haul roads is typically done by hand, or with the assistance of rudimentary shortest path optimisation algorithms. Straight line, point to point, modelling of costs is often used with distances multiplied by constants that are based on rise of the road between the points. Failings of this approach are that straight line approximations are notoriously poor as they do not take into account areas where a truck cannot travel. In addition, the rise and fall of the road may vary considerably over the truck journey meaning acceleration/deceleration and varying truck speeds are not taken into account. Lastly, the use of rudimentary optimisation algorithms means properties a truck must obey such as minimum turning circles, line of sight restrictions or even that the truck must travel forward at all times are not taken into account. Thus solutions generated may not be feasible, let alone optimal. In this paper we discuss a state of the art parallel Artificial Intelligence tree search technique for solving haul road location problems. As well as the above properties, factors such as road utilisation, cut and fill, and construction costs are taken into account. The combination of advanced modelling and fast computing and optimisation techniques produces significant benefits both in terms of time to generate roads and cost savings. Preliminary results where this method has been used are discussed.

Aug 1, 2013

By G. Ellie, D. F. Coates

"The mining of coal in thick and inclined seams is difficult, and there are only a few countries in the world that are really interested in the problems associated with their exploitation. In France a considerable amount of investment has been made in the mechanization of systems appropriate for such conditions.For seams inclined up to 50 degrees, of normal thickness, a new system was introduced in 1967. It consists of a longwall advancing to the rise with walking props, a shearer and hydraulic backfill. During the first two years the panel productivity was an average of 25 TN/MS, and they foresee the possibility of reaching an average of 30 TN/MS.A system for thick beds, both horizontal and inclined, is in p•rocess of being mechanized. In 1969 they started with a method consisting of a longwall in a footwall slice, or sub-level drifts with walking props, and caving and drawing up to a height of 20 m of coal. Recent experiments with a shearer have produced panel productivities between 9 and 11 TN /MS, and there is hope that with experience an average of 16 TN/MS will be obtained.In 1964 a method was initiated for beds inclined from 60 to 90 degrees, based on a mechanical cutter designed by the collieries in Lorraine. An overhand slice of 4.2 m in height is taken with a drum cutter mounted on the end of a boom. Hydraulic fill is placed at the completion of a slice. The face productivity, which has been from 13-20 TN /MS, can be perhaps increased to an average of 22 TN/MS. For those companies with important reserves in inclined and thick seams, these French systems may be worth the trouble of examining in some detail."

Jan 1, 1972

By Robert B. Parsons

"Originally intended to be implemented in 1977, but actually introduced effective May 6, 1974, the earned depletion regulations have been substantially refined and modified since their appearance on the Canadian tax scene, so that this important legislation now consists of a highly complicated set of rules which even the most astute follower of tax law has considerable difficulty sorting out!This month, Tax Notes attempts to cut through this bewildering array oj regulations, in reviewing the main features of the earned depletion allowance applicable to mining operations. Despite the phase-out of earned depletion allowances for most oil and gas operations as part of the federal government's new National Energy Program, earned depletion provisions are still alive and well for the mining sector, although they might well be slowly strangling to death in their own entanglement of complexity!"

Jan 1, 1981

By E. C. Harder

BRITISH Guiana, Great Britain's only South American colony, may be reached by very comfortable steamers, both from North America and Europe. The trip from North American Atlantic ports requires about 12 to 14 days; that from Europe about 18 to 20 days. A number of steamship lines, including Canadian, American, and Dutch, have regular sailings between North America and British Guiana, with calls en route at various interesting ports in the West Indies and northern South America. Moreover, several lines, including British, German, and French, have steamships operating regularly between Europe and the West Indies. Indeed, so popular have the West Indian voyages become in recent years that, during the winter months, special cruises in considerable number are organized for many vessels that ply in the trans-Atlantic service in the summer. A trip to British Guiana, therefore, has become a delightful experience. After visits at the various attractive Leeward and Windward islands and Trinidad, the approach to the low, flat, British Guiana coast, with its muddy coastal waters extending for many miles offshore, is somewhat of a contrast. Arrival in Guiana waters is signalled by the appearance of the modern high-power Demerara Light, located "on a shoal about twelve miles from the mouth of Demerara river. From this point, if the tide is right, a pilot takes the steamer across the bar, eight to ten miles offshore, and into Georgetown harbour. At high tide, the water above the bar ranges from 15 to 18 feet in depth, depending on whether it is neap tide or spring tide; at low tide, the corresponding depths are 9 to 11 feet. As the bar is of soft mud, however, it is usually possible for vessels to pass over it with a draught of about two feet in excess of that indicated by the tide tables. Upon nearing the shore, one sees first the Georgetown wireless towers, then the light-house and the tall chimneys of sugar mills and of various factories in Georgetown, and finally the palms and other tropical trees and the houses of Georgetown itself along the sea shore and the east bank of Demerara river. Extensive wharves operated by various exporting and importing companies stretch along the river bank and activity prevails in Georgetown harbour. The principal exports are sugar, rice, gold, diamonds, bauxite, balata, lumber, fruit and other tropical products. The imports are food-stuffs, wearing apparel, and manufactured materials of many kinds.

Jan 1, 1936

By Lloyd W. Trevoy

Syncrude Canada Limited is presently studying commercial production of heavy minerals from plant tailings of the openpit A lhabasca tar sands operation. When tar sands are processed and upgraded to synthetic crude oil, heavy minerals can be removed f rom the extraction circuit and beneficiated to provide concentrates of zircon and titanium minerals. Calculated recovery rates indicate that crude oil production capabilities of 105,000 barrels per day would provide 26,000 tonnes of zircon and 114,000 tonnes of titanium minerals annually. The titanium minerals concentrate is a mixture of ilmenite, leucoxene and rutile; it could be used as recovered or upgraded to synthetic rutile. With the consrruction of further synthetic crude oil plants in Western Canada, a large reserve of heavy minerals will become available.

Jan 1, 1984

By W. Jomaa, V. Songmene, O. Mechri, Laval Université, P. Bocher, J. Levesque

"A 2D finite element modelling (FEM), based on pure Lagrangian approach, is developed for studying the serrated chip formation during high speed machining (HSM) of 7075-T651 alloy. The solution was achieved using a commercial software package, ABAQUS/Explicit v6.13. The Johnson-Cooke (JC) constitutive equation is used to describe the work material behaviour. Moreover, the JC damage equation is implemented into the FEM to take into account for the shear localization during the serrated chip formation. Modified Coulomb friction model has been used to characterize the sliding/sticking effects on the tool-chip interface with the friction coefficient and shear flow stress determined by force calibration and machining data, respectively. The proposed FEM is validated using experimental data obtained in HSM of 7075-T651. The FEM was able to predict accurately serrated chip morphology. The intensity of chip segmentation was found to increase with cutting speed.INTRODUCTIONHigh speed machining (HSM) is one of the most used processes for manufacturing aircraft parts with aluminum alloys. For aluminum alloys, the use of HSM increases metal removal rate and reduces the formation of built up edges and burrs. However, it was found that serrated (also named segmented or sawtooth chip) and discontinuous chips can be produced during HSM of some high strength aluminum alloys, such as 7075-T6 alloy (Rao & Shin, 2001). Many parameters were found to affect the segmented/discontinuous chip formation during the machining of aluminum alloys.There are two cases in which the serrated chip can forms: the first is when machining hardened materials (Morehead, Huang, & Luo, 2007), and the second, when machining ductile materials with a cutting speed higher than a critical value (Barry & Byrne, 2002). Different theories and models were developed in order to explain the formation mechanism of such kind of chips. According to Astakhov (2006), the segmented chip formation is attributed to variations in stress and plastic deformation states, and resulting temperatures on the cutting zone. Liyao et al. (2013) stated that the segmented chip formation was mainly attributable to adiabatic shear instability/catastrophic strain localization. Others (Vyas & Shaw, 1999) suggest that the fracture/crack propagation mechanism is at the root of chip generation."

Jan 1, 2016

By Pierre Buteau

Peat/ands distribution in Canada is widely spread thoughout the country and corresponds to a wide spectrum of wetland habitats which overlay peat deposits. The development and the evolution ofpeat/ands and peat deposits are closely linked together, since the vegetal remains of the peat deposits originate from the peatland habitats, and the peatland habitats constitute a response to many factors, including the properties of the substrate, which are the peat deposits. Peat/ands are defined as waterlogged terrains where the production of plant materials usually exceeds the rate of decomposition. The underlying peat deposits consists of organic residues associated to peatland vegetation, more or less decomposed, built up and kept under anaerobic conditions. Peat/ands evolution and distribution are determined primarily by climatic factors, but also by the geomorphology and edaphic conditions. All of these create particular hydrodynamical environments which will vary according to different regional settings, and sequentially to an evolutive time frame.

Jan 1, 2001