Search Documents

By Robert S. MacPhail, Chilombo Henry, Arnold Kabamba, David Mukelebai, Suresh Thirunagari, Bukali Victor, Yoram Kapai, Chomba Leonard, Kanna Amarasingham

"FLEX 31 is a chemically enhanced sodium isopropyl xanthate. Developed by Charles Tennant & Co (Canada) Ltd and has shown improved collection properties over SIPX for sulphide minerals flotation. Improvement of recoveries, grades, faster kinetics, lower dosages, high pyrite and pyrrhotite rejection capabilities have all been exhibited by FLEX 31. Recent plant trial carried out in the copper circuit at one of the largest copper mine in Zambia shown over US $ 2.00 Million annual improvement on the bottom line over SIPX at current copper prices. Data produced also showed superior grade and recoveries from rougher concentrates that previously had not been attainable with other reagents effectively. Flex 31 has also shown positive outcomes with zinc, Copper/Zinc, arsenopyrite and copper/molybdenum ores.IntroductionSodium Isopropyl Xanthate (SIPX) is one of the most popular flotation chemicals on the market today. Somewhat more specific than amyl xanthate, SIPX is used in a variety of ores like copper/zinc, lead/zinc, arsenopyrite/pyrite, and many others (Melis et al., 1991). An investigation carried out by the research division of Charles Tennant & Company (Canada) Limited has produced a chemically enhanced SIPX. This product has shown all the advantages of normal SIPX along with improved recoveries of copper and copper activated minerals. The product was named “FLEX 31”."

Jan 1, 2016

The #3 Shaft at Brunswick Mine, Bathurst, New Brunswick, Canada, intersects a soft graphite zone just below the 3400 Level. Ground movement within this zone causes the concrete liner of the shaft to be deflected towards the shaft?s interior, affecting the steel framework of the conveyance. In some areas, the clearance between the cage and the liner has been reduced to less than 2 cm, which is a concern. An innovative surface-mounted extensometer was designed in 2008 to monitor potential movements of the shaft?s liner. Four such novel extensometers were installed in the shaft for the surveillance of a particularly critical 3.0m by 5.5m area. This article describes the approach taken to instrument the shaft, the principle of the new extensometer, as well as the performance of the instrumentation following its installation.

May 1, 2009

By Philip A. Dirige

This paper presents the variability of responses of paste backfill specimens that have been prepared with varying binding agent and binder combinations, when subjected to uniaxial compressive strength testing. A testing program conducted for an underground operating mine to produce cost efficient paste fill recipes using four different binding agents, in various ratios and combinations, is presented to illustrate the responses. These binding agents are Normal Portland Cement Type-10 (NPC T-10), oxidation or sulphide attack resistant binder (Binder A), replacement binder B (Binder B), and replacement binder C (Binder C). The paste fill recipes were prepared at 2, 3.5 and 5% binder content at varying binder combinations, at fixed size and tested in a Material Testing System (MTS) under constant strain rate conditions following cure times of 7, 14, 28, 56, 90, 112, 180 and 240 days. The results of tests suggested that the strength data clearly shows a trend of increasing strength with increasing binder content but not necessarily cure time. It is noted that all the blends achieved dramatic increases in strength up to 28 days of cure and then either increased or decreased moderately beyond 28 days curing, depending on the binder content and binder combination. The moderate decrease is apparent for the 2% paste fill blends and in some binder combinations of the 3.5 and 5% blends, which indicated lackluster performance beyond 28 days curing. This lackluster strength performance indicated that the binder content and combination may not be sufficient for the paste fill to achieve complete hydration and acquire adequate strength performance beyond 28 days. This study indicated that economic paste fill recipes can be designed with confidence using affordable alternative binders. However, it is noted that these alternate binders cannot be used as stand alone binders but should be used in combination with NPC to facilitate hydration of the paste fill.

May 1, 2006

By John H. Fowler

"Most of the aggregate used in Nova Scotia is produced from numerous glaciofluvial and ice-contact deposits scattered throughout the province. Production from bedrock sources is increasing, with most of the coarse aggregate used in the Halifax-Dartmouth area coming from quarries operating within the metro area.A recently completed provincial sand and gravel inventory mapping program has identified some ""resource-poor"" areas where comprehensive aggregate evaluation programs are underway. Although some areas of the province are experiencing aggregate supply problems, large volumes are exported to markets as far away as Bermuda.IntroductionThe Nova Scotia Department of Mines and Energy has been involved with aggregate resource studies for several years, although sand, gravel and crushed stone are not designated as minerals under the Mineral Resources Act of Nova Scotia. Our role has been to provide the aggregate industry with resource data as well as provide similar information to governmental agencies involved with municipal planning, water resource studies and environmental protection regulations. Several private consulting firms use the information in many of their site development studies.We became involved with aggregates in a rather roundabout way. Several years ago, an outcry from inhabitants of a small coastal community over the removal of sand and gravel from a local beach moved the provincial Department of Lands and Forests to take action to protect provincial beaches. We were asked by the Department to provide information and to suggest alternative sources here operators extracting sand and gravel from beaches could relocate. This request initiated an aggregate inventory survey in southeastern Cape Breton, which was later extended to cover the entire province. The initial provincial sand z and gravel inventory survey provided a series of 1:50,000 maps showing the distribution of sand and gravel deposits in the province."

Jan 1, 1982

By P. P. Rosario, D. M. Maijer

The primary crusher is a key component in the comminution process applied in open pit mines. A collaborative research project between the University of British Columbia and Highland Valley Copper (HVC) was conducted aiming at understanding gyratory crusher liner wear in the overall context of the crushing process. This paper presents an analysis methodology applied to data collected using a laser-based tool for assessing wear in gyratory crushers. Data from the wear measurements was correlated with crusher production information such as current draw and throughput. As a result of the knowledge developed during this work, an innovative way to evaluate crusher liner profiles was created and new mantle profiles were designed. This led to a reformulation of HVC’s standard liner management policy with a resulting estimated annual savings of 13% in total crusher liner cost and a 15% reduction in liner replacement downtime.

Jan 1, 2006

By B. K. Gorain, A. W. Stradling

"The traditional metallurgical scale-up techniques for flotation plants are based on lumped flotation rate constants, dimensionless hydrodynamic numbers and the use of safety factors. Once the plant has been designed, the flotation principles that govern scale-up play almost no role in the optimization of the circuit to meet its metallurgical targets. This deficiency can potentially lead to a plant design incapable of meeting its targets, especially when circuits incorporate large flotation cells. This paper demonstrates the application of the k = PSbRf model in providing a suitable framework for flotation modelling, scale-up and circuit optimization, thus presenting an integrated approach to the problem. Studies were conducted at Teck Cominco’s Red Dog concentrator to characterize cell hydrodynamics, gas dispersion properties, froth flow behaviour, entrainment and ore floatability to obtain the key data necessary to develop a model for the flotation circuit. The findings of these studies are presented in this paper, which provide valuable insights into the modelling and optimization of the Red Dog flotation circuit. IntroductionThe traditional methodology for flotation scale-up and plant design is based on the ruleof- thumb with safety factors and dimensionless hydrodynamic group similitude considerations. With the recent trend toward larger flotation cells with volumes of 150 m3 and greater in concentrators, the problem of scale-up has become even more acute. The scale-up factors that may have been tolerated on smaller cells are not applicable to larger cells. The transportation of froth in these large cells adds further complexity to the problem. Arbiter et al. (1980) foresaw this problem and pointed out that if scale-up were attempted by rule-ofthumb and trial-and-error, the probability of failure would then increase with scale. This problem is confounded by the fact that the design and scale-up considerations used for a new flotation circuit play almost no role in optimization of the circuit to meet its metallurgical target. This results in a plant design, which may be incapable of meeting its metallurgical targets. There have been several instances where new concentrators have required significant circuit modifications and additional capacity to achieve design targets."

Jan 1, 2003

By Margarete Kalin

"Biotechnological approaches to decommissioning of mine waste management areas are presented in the context of sustainable environmental management. Improved design of waste sites and environmental management paves the way for the application of new technological approaches. Mining wastes are better confined, effluent quantity is reduced and the quality is expected to improve in the future. The biologically mediated treatments focus on the creation of conditions inside the waste management area which lead to the confinement of the contaminants in the inactive tailings ponds and seepage collection ponds, as well as pits or other disturbed areas which were part of the operating conditions.Biogeochemical reactions lead to three fundamental water treatment steps mediated biogeochemically , alterations in chemistry which lead to formation of particles, which then have to flocculate and be assisted to collect in the bottom of the ponds. Microbially active sediments are installed to assist particulate formation and serve as sinks for metals. In deeper sediment strata, stable forms of metals are created. Biological polishing is used to collect the particulates and relegate them to the sediment. Examples will be given of the application of these processes, to waste rock piles, open pits and tailings ponds. This paper attempts to show that, through the integration of applied biotechnological advances and the application of new approaches to decommissioning, reductions of environmental impacts by mining are possible. * Note: this paper has been presented at the 13th Annual Meeting of BIOMINETIntroductionThe role of biotechnology in decommissioning of mining waste management areas should be placed in the context of sustainable development. The concept of sustainable development as defined by the Brundtland Commission (1987) for the restoration/ reclamation of mining operations could be translated as follows: The increasing demand for the resources by the world population must be met in a manner which does not compromise the earth's environment over the long term (Brooks et al., 1995)."

Jan 1, 1998

By Peter Claus

In the last years, supported gold catalysts with particle sizes smaller than 10 nm have attracted a lot of attention. While gold bulk metal is rather inert in chemical reactions and, thus, is of low interest for catalysis, highly dispersed gold particles supported on oxides as TiO2 or ZrO2 show surprisingly high activities in some reactions important for the chemical industry. The oxidation of carbon monoxide at low temperatures is mainly used as model reaction to study the unusual properties of gold catalysts [1]. On the other hand, to evaluate the catalytic potential of gold, other chemical reactions which allow to control also the selectivity have to be considered. The selective hydrogenation of ???-unsaturated aldehydes to allylic alcohols is of both commercial relevance (e.g. in fine chemical and pharmaceutical intermediate production) and specific scientific interest [2]. Note that thermodynamics favors hydrogenation of the C=C over the C=O group (stronger negative free reaction enthalpy of 35 kJ/mol), and for kinetic reasons the C=C bond is more reactive than the C=O group. Thus, in the presence of most of the conventional hydrogenation catalysts, based on Pt, Rh or Pd, -unsaturated aldehydes such as acrolein and crotonaldehyde are hydrogenated predominantly to the saturated aldehydes and only to a minor extent to unsaturated alcohols. Therefore, it is desirable to find catalysts which are able to control the intramolecular selectivity by hydrogenation preferentially the C=O group while keeping the olefinic double bond intact (Fig. 1).

Oct 1, 2003

By Q. Zhang, J. A. Finch

"Sphalerite flotation in the absence of copper activation at moderately alkaline pH has been observed in laboratory studies. An in-plant test of this observation was conducted at Kidd Creek Mine LTD. using a portable minicell flotation circuit. The results confirm that raising the pH causes sphalerite flotation.The testwork with the minicell circuit is described. The circuit, built around 2, 51 cells donated by the Noranda Technology Centre, was funded by Air Liquide and NSERC. It includes a data acquisition system to monitor continuously dissolved oxygen, pH and Pulp potential.INTRODUCTIONFlotation of sphalerite is normally practised by adding CuSO4 as an activator under alkaline pH. Recently there have been a number of laboratory and plant examples of sphalerite flotation without deliberate addition of cu++ ions (Girczys, 1972; Mukherjee, 1976; McTavish, 1980; Marouf et al., 1986; Mielczarski, 1986; Leroux et al., 1987; Palsson and Forssberg, 1989; Sandoval-Caballero et al., 1990; Zhang et al., 1991).In batch tests, with a sample of Pb/Zn ore from Polaris, Leroux et al. (1987) found that sphalerite became floatable after adjusting pH to 9. 5-11: they ruled out natural floatability or the formation of elemental sulphur on the surface but suspected iron hydroxy compounds were responsible. Sandoval-Caballero (1990) conducted a continuous minicell test at Brunswick Mining and obtained a 44 % Zn recovery and 40.5 % Zn grade concentrate without deliberately adding CuS04 at pH= 10.5. With single mineral studies, Zhang et al. (1991) revealed good sphalerite floatability (over 80% recovery) in pH range 8 to 11 and found that this floatability was related to pH, dissolved oxygen (DO) level and Fe++ species present in the system.To explore further the conditions under which sphalerite can float without addition of CuSO4 , a continuous pilot test using minicells was performed at Falconbridge Ltd., Kidd Creek division. The set-up is briefly described (a more detailed description is given elsewhere in these proceedings) with emphasis on the data acquisition system - dissolved oxygen, pulp potential and pH were monitored continuously. Results of testwork investigating pH, CuS04 addition and gas composition are presented."

Jan 1, 1992

By Vanessa C. Koppe

During ore body modeling normally additional samples are required to improve resources evaluation and mining planning. At this stage one rises the question about where additional samples should be located. Regular sampling pattern seems to be a reasonable choice, since all the regions within the deposit receive the same number of samples without a clear clustering. Nevertheless, values for certain attributes (grades for instance) from a mineral deposits may behave more erratic in some regions than others. Consequently, by adding samples to these regions could bring more benefit for reducing the uncertainty related to a transfer function such as Net Present Value (NPV), instead of adding samples to location of low grade uncertainty. Thus, for a given number of additional data, the test of a regular pattern and a pattern which add samples on areas of high uncertainty of the attribute of interest is worth. This paper presents an algorithm that allows the construction of these two patterns, automatically, on a software commonly used in the mining industry. The algorithm leads to a fast analysis on the efficiency of the two patterns in reducing the uncertainty associated with a transfer function.

Oct 1, 2009

By Brigitte J. Dejou

The Red Dog sediment-hosted zinc-lead deposit is located in the Brooks Range thrust belt in northwest Alaska, approximately 1000 km northwest of Anchorage. The mine constitutes the primary deposit in a 400 square kilometre district, which hosts several other mineral occurrences. All the known mineralisation is hosted by the Mississippian Ikalukrok Member, deep basinal shale of the Kuna Formation, part of a Devonian to Cretaceous sedimentary sequence. The rocks underwent intense deformation during the Brookian Orogeny in Middle Cretaceous time. Several thrust faults juxtapose the stratigraphy. The Red Dog mine is composed of four deposits which together contain 105 Mt in resources and reserves for a total resource exceeding 18 Mt of Zn metal. The mine is an open pit with 25 foot high benches. The biggest challenge is not the Arctic conditions, but metal extraction, due to the fine grained nature of the mineralisation and the variability of the ore. The mine produces Zn and Pb-Ag concentrates that are shipped to smelters around the world from the Red Dog port facilities during the short summer period. Ore mineralogy is generally simple and consists of sphalerite, pyrite, galena and marcasite. The deposits are generally overlain by decametre thick exhalative barite horizons and exhibit strong silicification, which locally obliterates the original textures. Although described as a world class Sedex-type deposit, a large portion of the mineralisation exhibits sub-surface replacement textures. Moreover, unlike most other Sedex deposits, the reconstruction of the basin is made difficult by the structural complexity of the district. To assist exploration in the district, several assumptions are made regarding the deposit settings relative to metal source, growth faults or crustal extension.

May 1, 2006

By Denis Thibodeau

The selected mining method for the Rodeo lower Zone is slot and slash. Initial design indicated that the stope height should be limited to a maximum of 18 m, thus six levels were needed to extract the ore. Higher stope height in the Rodeo Lower Zone means less development thus less capital required to extract the available reserves. It was proposed to eliminate one level by establishing 30 m and 24 m level intervals. To ensure that no stability problems will be encountered by eliminating one level, a Matthew analysis, based on diamond drill core information, was performed for the Lower Rodeo Ore Body. In addition, comparisons between the rock mass quality of Meikle Main Zone below 1825 L and Meikle East Zone between 1600 L and 1750 L with the rock mass quality of the Lower Rodeo were made

May 1, 2002

By Frederic M. Langevin

?? Introduction ?? LaRonde ?? History of Seismicity and Rockbursting ?? November 27th 2002 Rockburst ?? April 1st 2006 Rockburst ?? December 11th 2006 & January 11th 2007 Rockbursts ?? Seismic Risk Management Plan ?? Conclusions ?? Located in Northwestern Quebec (Can.) ?? In operation since 1988 ?? Reserves at Shafts #1 and #2 depleted ?? Production now comes entirely from Penna Shaft ?? Deepest single-lift shaft in the western hemisphere (2240 metres) ?? 7300+ tonnes per day ?? 2007 Reserves (proven & probable): ?? By-products: Ag, Cu, Zn ?? Sinking #4 Shaft (LaRonde II winze)

Feb 1, 2008

By Karl J. C. Harries

13.1. RIGHT TO RECEIVE ROYALTY CONTRACTUAL ONLY1

Jan 1, 2003

By A. W. Stradling, M. J. Fairweather

"The selective flotation of lead, zinc and iron sulphide minerals is key to the economic performance of concentrators treating zinc-lead ores. Diagnostic metallurgy is a tool to quantify mineral behaviour as a function of particle size and liberation. The result of such analysis may be used to select preferred strategies to improve metallurgical performance. The zinc flotation circuits at three Teck Cominco operations: Sullivan, Polaris and Red Dog are compared here. This paper analyses operating data from each of these circuits. The effects of mineralogy and performance by particle size are emphasized. Metallurgical performance at these three concentrators varies substantially. Liberation size is the major factor in determining metallurgical performance. Complex mineralogy requires a fine grind to achieve effective liberation. Fine grinding results in offsetting decreases in concentrate grade through entrainment. The economic treatment of complex fine-grained deposits requires optimisation of regrind size for liberation without unduly compromising concentrate grade through gangue entrainment.INTRODUCTIONUntil recently Teck Cominco Metals Ltd. operated three mines treating zinc-lead ore. In order of increasing mineralogical complexity they are: the Polaris Mine on Little Cornwallis Island in Nunavut in the eastern Arctic, the Sullivan Mine in southeastern British Columbia and the Red Dog Mine in northwestern Alaska. Both the Polaris and Sullivan Mines have recently ceased to operate due to depletion of ore reserves.The ore type and associated gangue, mineralogy and iron solid solution vary significantly between these deposits. Table 1 summarizes some of the important differences"

Jan 1, 2003

By D Reddy Chinnasane

Outline Location of BirchtreeMine and Layout of 124 OB Cut and Fill Mining Background Purpose of the Studies Methodology Results and Analysis Conclusions and Recommendations

Oct 1, 2010

By Karim El-Ouassiti, Marc Minville, Stéphane Chabot, Claude Bazin, Valérie Ouellet

"Alumina is the main source of aluminium and it is extracted almost exclusively from bauxite ores found in the Southern hemisphere. Clays are abundant minerals that contain from 15 to 40% w/w of alumina from which it can be extracted by various processes. This paper reviews the processes used for the extraction of alumina from clays and discusses results obtained with a clay sample from the Murdochville area in the Quebec Province. The application of a conventional process to this clay did not yield an acceptable recovery although smelter grade alumina was produced. A modification to the process allows increasing alumina recovery from 85% to more than 92%. The application of the improved flow sheet to other alumina carriers failed to yield comparable recovery, showing that an optimum processing path for the recovery of alumina should be found for individual clay materials.INTRODUCTIONMost of the aluminium smelters are fed with alumina extracted from bauxite found in the Southern hemisphere. Bauxite is processed by the Bayer process that uses a caustic leach of the ore. In the middle of the century, the US Bureau of mines, motivated by the fear of an alumina delivery disruption, conducted several research projects aiming at producing alumina from non bauxitic ores. These projects led to the development of various acid leaching processes (Habashi, 1993). The sulphuric and hydrochloric acid leaching processes were brought to pilot plant evaluation (Bengtson, 1979), while nitric and other leach liquors were tested in the laboratory (Phillips and Wills, 1982; Habashi, 1983). Although clays are abundant and inexpensive minerals, the studied processes remained uncompetitive with the alumina extraction from bauxite (Hudson, 1987 page 42; Peters et al., 1962) for which reserves are estimated to support alumina production for the next 50 years (Oye et al., 1999). On the other hand, the local extraction of alumina from clays could significantly reduce the transportation costs of alumina to smelters and provide an alternative source of alumina supply from the Southern hemisphere countries. Also, the extraction of secondary products for some types of clay (Nasyrov et al., 1999) containing significant amounts of potassium and sodium could provide an additional return that may improve the economics of alumina production from clays."

Jan 1, 2005

By Horst Konig

This paper illustrates that, with the application of new processes, smaller steel plants using local raw materials can be economical and advisable. It also introduces the problems connected with the direct reduction processes, which use non-coking coal or gas as reducing agents, and which are employed in connection with conventional reduction to produce excellent results. Electric smelting is also discussed, and some practical examples of operating plants are given.

Jan 1, 1970

By Zdenek D. Hora

British Columbia is an important producer of a variety of industrial minerals for both domestic and export markets. Some commodities such as limestone, dolomite, gypsum, calcium carbonate, silica, barite and magnetite are raw materials for well-established industries located in British Columbia, Alberta and northwestern USA. Others, like magnesite, sulphur, jade, asbestos, dimension stone and clay products, are mainly exported in processed form to overseas customers. Companies are developing markets for relatively new mineral products, including pumice, volcanic cinder and zeolites. A number of attractive geological targets have been identified by industry while research by government geologists has outlined the potential for refractory minerals, gemstones, garnet, nepheline syenite, carbonatites, residual kaolin, igneous apatite and peat.

Jan 1, 2001

By T. B. Armstrong

"The developing world energy crisis and spiraling fuel costs have created a new public awareness and general acceptance of the need for energy conservation.Plants will have different objectives for an energy conservation program but there appears to be a common approach on how to save electrical energy.Data for a 180tph Rod Mill powered by a 750 hp motor will be used to demonstrate the relationship of energy input and production levels and to seek an optimum operating condition.Energy Conservation:Plants that have examined ways of dealing with the energy situations have concluded that energy conservation has important benefits for industry, including reduced costs, fewer production slowdowns inthe event of fuel shortages and a continued competitive position.There have been some ""startling"" conservation achievements attained through such simple plant maintenance and operating practices as reducing unnecessary lighting in buildings and yards, turning off' equipment not needed at night or over week-ends, through planning maintenance and production schedules to minimize energy use and through improving quality control to eliminate waste.Significant reducti.ons in energy use have been achieved by some rather simple but vigorous maintenance and plant engineering efforts directed at finding and fixing energy ""leaks"" rather than technological advances or major rework or redesign of facilities and equipment.An Energy Conservation Program often must overcome such obstacles as historic operating practices and emp1-oyee indifference, i.e. the ris.ing costs of fuel should result in re-examination of so1ne basic attitudes to energy conservation. Some measures, rejected in the past largely on the grounds of capj.tal. expenditure, now make economic sense in the light of future escalating energy costs."

Jan 1, 1978