Search Documents

By Kelly E. G

NZ Steel's flushing slag typically contains 1.2 per cent V203. Extraction of vanadium from powdered slag using a salt (NaCI or Na2CO3) roast/leach process was investigated. With NaCl, optimum extraction conditions were a charge containing 10 per cent NaCI, roasting in air at 875°C for 4 hours, followed by leaching in dilute H2SO4. Extractions were typically 30-50 per cent. NaCI roasting did not chemically attack the slag; the phase transformations that occurred were due to high temperature oxidation. Slag particle size had a significant effect on extraction.Optimum conditions for extracting vanadium by Na2C03 roasting were 20 per cent Na2CO3 in the charge and roasting in air for 3-4 hours at 850-875°C followed by water leaching.Na2CO3 roasting involved chemical attack that resulted in the formation of perovskite (CaTiO3) and carnegieite (NaAISiO4).The extent of vanadium extraction depended on the amount of Na2CO3 added and the original slag SiO2 content.Compared to the separate roasting treatments, simultaneous treatment with NaCI and Na2CO3 gave lower vanadium extraction, while requiring considerably higher roasting times and temperatures.

Jan 1, 1982

The problem of ventilating an advancing drive which finally reached 5,550 ft from the fresh air base in rock with virgin temperature of 83°F was solved economically by the use of two 15 h.p. electric fans forcing ventilating air through 281/2 in. dia. fiexible polythene tubing of wall thickness 0·010 in. The saving in cost over conventional metal duct was estimated to be £3· 24 per ft of drive.INTRODUCTIONAs described by Dutton (1965) and Newton (1965) the existing 1,480' ft level drive at the South Mine, Broken Hill, was extended in two stages. The first extension was 3,790 ft, the face then being 4,790 ft from the fresh air inlet. Later, after a vertical ventilation connection was made 1,000 ft back from the face, the drive was extended a further 4,550 ft. The rate of face advance in both stages was about 15 ft per day (3 shifts of 5 ft), 5 days per week. Drive size was 8 ft by 9 ft 6 in. high.The Mines Inspection Act of New South Wales requires 6 hr shifts (instead of the normal 7 in Broken Hill) to be worked if the wet bulb temperature exceeds 80°F. Virgin rock temperature on the 1,480 ft level was 83°F. Inlet air temperature varied with seasons from 58 to 72,oF wet bulb.To adequately ventilate the face, a flow of air of about 11,000 c.f.m. was thought to be necessary.Re-entry time was about 75 min, being governed by the 7 hr length of shift (3 shifts per day) and travelling time.Blasting was permitted only at the end of the shift, in accordance with local industrial restrictions.

Jan 1, 1965

By Met B

IN the followmg paper an account is given of work performed by the author for the purpose of sampling a slime dam on the leases of the North Mount Farrell Co. N.L., at Tullah, Tasmania, during the summer of 1925-26.For convenience the paper is divided into sections as follows:1. THE MINE2. THE SLIME DAM3. SURVEY OF THE DAM4. BORING OF THE DAM(a) INTRODUCTION(b) 1ST METHOD(c) 2ND METHOD(d) 3RD METHOD(e) 4TH METHOD(f) GENERAL NOTES5. CONCLUSION

Jan 1, 1928

Geochemical data on Australian granites and pegmatites, and the mineral components of these rocks, are compared with that obtained in similar studies in the U.S.S.R. and elsewhere.The geochemical character of tin granites and the trace chemistry of their component minerals, particularly biotites, have some significance as ore guides in prospecting for tin.The primary geochemical dispersion of tin can be readily tested both in the laboratory and field by colourimetric methods, after volatilization with ammonium iodide, using modifications of the method described by Wood (1958).Secondary dispersions of tin in residual soils or alluvia can likewise be readly tested by rapid colourimetric methods in the field, but simple hydraulic methods, handling larger sample volumes, give reliable outlines of dispersion patterns.INTRODUCTIONThe search for tin ores, whether lode or placer in type, is usually directed on genetic grounds to country within or adjoining acid intrusives.A long established means of prospecting is to test samples for cassiterite by panning or other hydraulic separation.These methods can be used on crushed lode material or the natural materials from placers.With the advent of new techniques for extraction and for colourimetric analysis for tin (Wood, 1958 and Ross and White, 1961) a means is available for rapid analysis of materials not susceptible to quantitative testing by hydraulic methods because of the fine sizings of cassiterite or the occurrence of tin structurally held in minerals. The new methods thus opened up the field of tin prospecting by extending the search for ore guides to genetically associated rocks and minerals, wall ror-ks of veins and a wider range of superficial deposits.

Jan 1, 1963

Suggestions have been made at various times that there may be a recurrence of lodes similar to those at Kalgoorlie in the country to the south of the Golden Mile, but, so far as is known, there has been no geological evidence to support these suggestions apart from the possible extension of the younger quartz-dolerite greenstone in this direction.Geological mapping carried out by the writer in the Coolgardie district in 1946, provided some additional geological evidence to support this claim, and the ideas then held have since been expanded and are now considered to be sufficiently advanced to present them as concrete suggestions. As will be seen from the following pages, the critical area for lode prospecting is Hannan's Lake, where the basement rocks may include younger quartz dolerite greenstone, which, although perhaps distributed over a smaller area than at Kalgoorlie, could, on structural grounds, have a similar fracture system and similar ore deposition.There is little need to stress the importance discoveries in this area would have in prolonging the life of the field, and stimulating the post-war gold mining revival.Previous Work: Only the publications having a direct bearing on the preparation of this paper are given in the list of selected references, but the writer is very conscious of the fact that much other geological work has been carried out in the Kalgoorlie district since its discovery, by the W.A. Department of Mines, by mining companies, and others, all of which has contributed to the present knowledge of the field, and acknowledgment of the value of this work is given herewith. In presenting the suggestions in this paper a broad structural control of ore deposition is assumed, but this has already been established in other parts of the goldfields of Western Australia, including adjacent areas. In the early nineteen thirties, the Western Mining Corporation commenced work on the basis that there was a close relationship between geological structure and auriferous ore deposition, and a similar approach was first made by the Geological Survey of Western Australia in the South Yilgarn in 1935. These ideas were further developed during later surveys, particularly in the North Yilgarn and the Mount Margaret Goldfield.During the Coolgardie Survey in 1946, broad structural mapping was done in greater detail than before, and the structural ideas were implemented and further developed, leading to some success.Other work to which particular acknowledgment is given is that of Stiltwell, Gustafson and Miller, Forman, Prider and Finucane, at Kalgoorlie, and that of Honman in the Kalgoorlie-Coolgardie district, references to which are given at the end of this paper.Valuable constructive criticism of this paper has been given by Professor E. de C. Clarke and Dr. R. T. Prider, of the University of Western Australia.

Jan 1, 1950

By S Taylor, B Lumsden, G Long

Statistical metallurgical plant trials are becoming more widespread, as a valuable tool for increasing plant profitability. Generally, a single parameter like metal recovery varies under the trial condition while all other variables such as average metal feed grade or average metal concentrate grade are equal for the two test conditions during the period of the test. Metal recovery is usually the measured variable because concentrate grade is fixed by smelter terms, and plants operate to maximise recovery at the required concentrate grade. However, in all flotation plants there is a relationship between concentrate grade and metal recovery, and under the same conditions increasing one results in a decrease in the other. At MMGÆs Rosebery Mine the zinc concentrate produced is generally above smelter specifications, so zinc concentrate grade can vary during a test. During trialling of magnetic conditioning in the Rosebery zinc circuit, the difference in both zinc recovery and zinc concentrate grade were analysed. The analysis of changes in zinc grade and recovery during the trial raised some interesting questions about the relationship between concentrate grade and recovery. A paired statistical method was developed and tested to combine in each pair the change in concentrate grade and recovery in a single result that could be analysed by a paired t test. This method was found to be very sensitive to combined, varying changes in concentrate grade and/or metal recovery. It was also evaluated on plant test results from another flotation plant to verify its applicability in other plants. CITATION:Long, G, Taylor, S and Lumsden, B, 2012. Statistical plant trials - Efficiently combining concentrate grade and metal recovery results, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 355-362 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

As this is the first occasion I have had, and probably will be the only opportunity I shall have, of addressing such a large gathering of members and of student members of the Institute, I desire to- express my very deep appreciation of the honour 'you have paid me in electing me to the office of President for the current year. I realise also that such selection is a tribute to the Company which controls operations here, the centre selected for the annual meeting, but nevertheless there is afforded to the recipient a great deal of pride and of pleasure to hold the highest office in what is, in my opinion, undoubtedly the most important engineering society in Australasia.The past year has witnessed an unprecedented and unparalleled event in the history of the British Empire, and I think that we must all feel a wonderful sense of proud patriotism; the whole world was forced to admire the public calm and the dignity which accompanied the change in our Sovereign Ruler, and great tribute is due to the statesmanship of the Prime Minister, Mr. Baldwin. At this time, we should, I think, place on record our prayer, in common with all his people, that His Majesty, King George the Sixth, may enjoy a long and prosperous reign.The meeting at Port Pirie recalls one who did so much for the advancement of mining and metallurgy, especially in Australia. I refer to the late Mr. Delprat, who, as General Manager of The Broken Hill Proprietary Company Limited, had under his control for many years the smeltery in this centre. As you are aware, he had been elected an honorary member of this Institute, as well as of our sister Institutes in England and in America...

Jan 1, 1937

This paper describes a mobile laboratory developed specifically for nickel prospecting, and which was designed to be operated by sub-professional staff in remote areas independently of established laboratories. An atomic absorption spectrophotometric procedure was used to determine nickel, cobalt, lead, zinc, and copper ID latentIc and sulphIde samples, with a detection limit better than 25 µg/g for all elements. The procedure was applicable to both soil and drill samples and the accuracy of the procedure, which was ±5 per cent relative at the 1,000 µg/g level was sufficient for the preliminary assessment of mineralized samples and the control of drilling operations. The analytical procedure and the means taken to ensure the necessary reproductibility and accuracy are described. One operator can carry out 400 elemental determinations per 8-hr day at an approximate cdst of 6 cents per elemental determination. The results are returned within a single day, a factor which can contribute materially to the efficiency of drilling operations.

Jan 1, 1970

By Whiten W. J

An investigation on the breakage characteristics of closely sized orc samples at different levels of input energy was carried out to determine an appearance function for possible use in ball mill modelling. A consistent pattern of breakage behaviour was observed and the resultant size distributions could be described by a one-parameter, ('t'), family of curves. For each particle size range tested, this parameter 't' has an exponential relationship with input energy below an upper energy limit. A tentative linear relationship between the input energy at a constant value of 't' and the work-index leads to reconstruction of 'I' - input-energy curves from the work-index values. To normalise the efrect of particle size and input energy, multidimensional cubic spline regression was performed on thc entire range of data. The results indicated that the parameter 't' can be determined, reasonably accurately, as a function of Ln (input energy, kWh/tonne) and Ln (particle size, mm) for input energies between 0.5 and 8.0 kWh/tonne.

Jan 1, 1983

Experimental results are presented for the anode overvoltage as a function of current density for different alumina concentrations in an alumina reduction cell. Voltage changes due to the electrolyte resistance and also the decomposition voltage, have been evaluated as a function of alumina concentration and anode current density. From these values of voltage, changes in the total cell voltage have been derived for changes in alumina concentration for different anode current densities. The results show that for each operating current density there exists a discrete alumina concentration that defines a minimum reduction cell voltage. Discussion is made about potential savings in power consumption when the alumina concentration is controlled.INTRODUCTIONThe standard procedure in the aluminium industry when analysing the cell-voltage required for the Hall-Heroult process for reduction of alumina, is to subdivide the total voltage into the following components (e.g. Pearson, 1955; Maritell, 1960).1. ohmic drop through busbars and joints2. ohmic drop through cathode lining3. ohmic drop through anode4. ohmic drop through electrolyte5. overvoltage at anode6. electrolytic decomposition voltage.(Overvoltages ,at the cathode are of negligible magnitude at all practical current densities.)It is understandable that the voltages assigned for each factor invariably differ for different workers...

Jan 1, 1965

Selective Removal of Arsenic from Acid Mine Drainage Containing Ferrous Ion Using Sulfide Precipitation Method

Sep 13, 2010

Modelling and simulation are important aspects of flotation research, which may assist in the design of new circuits and the optimisation of existing ones. Flotation research in the AMIRA P9 project has developed a methodology for flotation plant modelling based on determination of cell (pulp) characteristics. froth characteristics, and ore floatability (using floatability components). The implementation of this methodology requires the determination of ore floatability, to which end a small flotation pilot plant known as the Floatability Characterisation Test Rig (FCTR) has been designed and then built and kindly made available to the AMIRA P9 project by Baker Process. The FCTR has a 2 tph capacity and consists of six 130 litre rougher/scavenger cells and six 50 litre cleaner/recleaner cells. The Mintek FloatStar pulp level control system is used to control the pulp level in all cells. A number of experimental procedures have been developed for using the FCTR to obtain the data required for the P9 flotation models. These procedures include how to determine the floatability parameters, Pi and mi, the bubble surface area flux, Sb, the mean residence of the pulp in the cell, t, water recovery. Rw, froth zone recovery, Rf, and the degree of entrainment, ENT. The flexibility of the FCTR allows it to be used in numerous flotation studies such as stream characterisation, reagent testing, grinding experiments, power studies, oxidation studies, and scale-up and simulation studies. This paper will describe the design and operation of the FCTR and the procedures that will be used to obtain data from the rig for modelling purposes.

Jan 1, 2000

The production of metallic titanium and titanium-rich alloys in forms useful to the engineer involves the use of certain techniques not usually necessary in fabricating the commoner metals and alloys. However, not all stages in the handling and shaping of titanium-base materials require the application of unfamiliar methods. It is the purpose of this paper to indicate where the well-known techniques are applicable as well as to outline the unusual operations which are necessitated by certain chemical characteristics of titanium.In brief, the characteristics just mentioned are manifestations of the very great reactivity of titanium, especially at elevated temperatures. Liquid titanium burns vigorously when brought into contact with air. It also reacts with practically all refractories, causing damage to the latter as well as undesirable contamination of the metal. Even solid titanium undergoes serious superficial contamination when heated above 800°C. in air for more than a few minutes. In addition to an oxide skin being formed, oxygen enters into solid solution in the surface of the metal causing the latter to become hardened and eventually embrittled.Up to date, titanium has been made only on a pilot plant scale by methods which produce a spongy or powdered product. Refractory problems have prevented the development of chemical reduction methods for making titanium in the form of a liquid pool from which ingots of useful size could be cast. Therefore the first part of this paper will cover the consolidation of powdered or spongy titanium. The latter portion will provide a brief description of...

Jan 1, 1950

Samples weighing O· 2 g are digested with 2 ml of 72 per cent perchloric acid for 2 hr at 180°C, and then diluted to 10 ml. with water. After settling, an aliquot of clear solution is reduced with ascorbic-citric acid, and then a zinc dithiol solution is added to form a coloured molybdenum complex which is extracted with petroleum spirit for comparison with standards.Concentrations down to 2 p.p.m. may be analysed at rates up to 150 determinations per day.

Jan 1, 1970

Geochemical projects in progress or recently completed in the Bureau of Mineral Resources, Geology, and Geophysics (BMR) cover a wide range of topics and include research projects, regional studies, and prospecting programmes. However, in these notes emphasis is given to projects which are directly relevant to mineral exploration.FIELD INVESTIGATIONSStream sediment sampling, rock and soil sampling, and geobotanical surveys have been used by the BMR in a number of areas, partly in attempts to locate specific zones of mineralization, and partly to investigate the effectiveness of the various methods under different conditions of climate and topopraphy and in different geological settings.Stream sediment sampling has been most successful in the Territory of Papua and New Guinea. For example, in the South Sepik area, zones of disseminated su1phide mineralisation were found to give rise to anomalies with peak values of up to 1,000 p.p.m. copper, compared with background values of about 40 p.p.m. (Dow et al., 1968). By contrast, the results of rather limited work in the Northern Territory and in the Kimberley district of Westen Australia were inconclusive.Rock and soil sampling, on the other hand, was successfully used in a number of areas in Northern Australia, particularly at Rum Jungle and Tennant Creek.Rum Jungle area In the Rum Jungle area, where uranium and base metal mineralization is mainly associated with a Lower Proterozoic black slate sequence, samples, of c-horizon soil or weathered 'rock are generally collectedfrom the bottom of drill holes, usually 15 to 20 ft deep, bored with a power-operated auger.Surface sampling indicates that such a technique would probably have shown up all the major geochemical anomalies delineated by deep sampling, but the latter gives slightly more consistent and slightly

Jan 1, 1970

During the last 125 years, the steel industry has witnessed revolutionary changes in the process of steelmaking. The Bessemer process was the predominant steel production technology during the last two decades of the 19th century. The open hearth process accounted for the lion's share of world steel production for six decades from 1910 to 1970. With the appearance of the LD process on the industrial stage in 1952, the importance of open hearth process declined and currently the basic oxygen processes are contributing more than 60 per cent of the world steel production. The LD process also led to the development of several other oxygen blown processes such as LDAC, OLP, OBM, QBOP, EOF, Clc.

Jan 1, 1999

Antimony ore samples (mean assay 18·7 per cent antimony) from Endeavour Inlet, Marlborough Sounds New Zealand, were tested for upgrading by flotation to a saleable product (60 per cent antimony).The effects of activating agents, collectors, frothers, pH, conditioning time, and particle size on the recovery and grade of a stibnite flotation concentrate were determined using HaIlimond tube and laboratory flotationcell test apparatus. Optimum flotation conditions for the ore were thereby established. A stibnite concentrate grading 63 per cent antimony and an overall recovery of 90 per cent is obtainable in a two-stage process.

Jan 1, 1977

Traditionally, capital costs of major resource development projects have been estimated as a single amount to which a percentage accuracy has been assigned based on the method of preparation of the estimate, that is, on the amount of information available to develop the estimate.However, there is a growing recognition of the importance of a probabilistic approach to capital cost estimates, and of a more rigorous calculation of estimate accuracies and of the presentation thereof. Accuracies can be expressed with more certainty as a percentage of the estimate amount where the percentage represents one standard distribution on the probability curve for the capital cost of that specific project. Thus confidence levels can be stated for various estimated amounts - for example, it can be stated that there is an 85% chance that a stated amount will not be exceeded, or a 90% certainty that a (higher) amount will not be exceeded. Moreover, the right skewness of the probability distribution curve for most projects can be readily recognised and reflected in the evaluations. This enables senior executives and board members to have a clearer understanding of investment uncertainties, and the possible magnitude of commitments.

Jan 1, 1990

By Koch D. F A

An electrochemical study of the dissolution of gold in aerated cyanide solution shows that the dissolution rate is determined by the nature of the surface. A passive film (probably a basic cyanide) formed at -0·6 V vs a saturated calomel electrode inhibits both the anodic dissolution of gold and the cathodic reduction of oxygen. Thallium has an "activating" effect on these reaction mechanisms.INTRODUCTIONIn general the dissolution rate of a solid in a liquid is studied by weight loss measurements or analysis of the solution at known time intervals. However, if the solid is a metallic conductor, on which a redox reaction can occur at the metal-solution interface, it can be studied by electrochemical techniques. Electrochemical measurements have the advantage that the overall reaction can be separated into its components, in some cases by electrical measurements alone, and in others by a combination of these with analytical determinations.The overall equation for the dissolution of gold in aerated cyanide solution may be written4Au + 02+ 8CN- + 2H20 = 4Au (CN)2- + 40H- ..... (1)which can be separated into the two electrochemical componentsrepresenting the oxidation of gold and the reductionof ogygen respectively.4Au + 8CN-,= 4Au(CN)2- + 4eand O2+ 2H20 + 4e = 40H- These two reactions occur at the gold-electrolyte interface and it is the purpose of this paper to discuss the mechanism...

Jan 1, 1964

By J Fut=

The rotary drilling of rocks is widespread technology in mining and in tunnelling. The paper describes the results of research by aim to find relationships between optimal drilling and sound signal of drilling machine. The optimisation criterion has been formulated as the minimisation of specific energy with maximal effective speed of drilling in process of the rock disintegration. The research in this field has been made on experimental drilling stand. Our monitoring system has measured following variables: the pressing force of core drill, the revolutions of drilling head, the length of drilling, the time, the power, and the acoustic signals. For measurement of acoustic signals have been used very sensitively sound meter MEDIATOR 2238. From this measurements have been processed acoustic spectrums. Then we are found relationships between optimal control of drilling and composition of acoustic spectrum. On base of experimental results, we can formulate the optimal control following: æTo achieve the minimum difference between the equivalent sound level at the load and idle modes only at the representative frequency (f = 1000 Hz)Æ. The representative frequency dependences on type of the rock New method based on these relationships enables the optimal control of drilling machine by using measured acoustic signals only.

Jan 1, 2003