Search Documents

By N Clarke, A Barros

Preconcentration of run-of-mine subgrade and marginal ore by screening has the potential to substantially improve the economics of mining, particularly for large, low-grade orebodies, and to reduce environmental impacts. It has recently been the subject of a major research effort by a joint public-private research body, CRCORE. Yet despite this, there appears to have been only one fully commercial installation, at Bougainville Copper Limited in the late 1980s. Two reasons for the limited application are that not all ores have suitable properties and the economics of all pre-concentration processes on low-grade materials are highly sensitive to the precise balance of mass and value recovery and to the pre-concentration process cost, including materials handling. These factors make it imperative to have good test data on the process response of feedstock across the orebody. Collecting that data presents major challenges, which differ for green and brownfields operations. This paper first discusses the approach to preliminary evaluation developed by CRCORE, which relies on testing of coarse rejects or drill chips available from exploration drilling programs. This method is an efficient first step in evaluating an orebody which is deemed geologically to be potentially amenable to screen upgrading, but it does have limitations and must be followed by larger scale work. A suite of methods have been developed by the authors as a result of test work since the 1990s on several projects, supplemented by published data, which aim to provide statistically robust data at lower cost than large scale bulk sampling tests. For greenfields projects, the upgrade response measured on material crushed to -53 mm has been found to correlate closely with ROM ore, with no scale-up required for material with upgrade responses in the range of commercial interest. Large diameter whole drill core, such as PQ, is expected to be suitable for this method. As drilling such core is costly, the aim should be to establish relationships between upgrade performance and proxy measurements such as multi-element chemical or hyperspectral analyses. This approach was successful at the Gramalote gold project in Colombia. The method is not applicable for ores with thick vein material comparable with the crush size, but such material is not suitable for upgrading by screening and would be eliminated by the preliminary testing. For brownfields projects where blasted material can be sampled, the upgrade response can be accurately measured by sampling only the finer fraction of the ore, selecting a top size which represents 30–50 per cent or more of the ROM size distribution. This is likely to be between 50 and 100 mm. The much finer size compared with the full ROM ore greatly reduces the sample mass required to achieve a given intrinsic sampling error and enables sample preparation to be undertaken with large-scale laboratory equipment rather than mobile crushing plant. The accuracy of the method can be improved by measuring the approximate mass of oversize rejected during sampling. Some ores do show a systematic deviation from the assumed model fit which results in this method slightly underestimating the upgrade response, and it would therefore still be recommended to take one or two full bulk samples to confirm results before a final investment decision.

Aug 24, 2022

By J T. Carswell, N A. Schofield

Fluctuations in periodic reconciliations between the mine and the mill are an expected and common experience in mining and processing operations. These fluctuations are caused in part by errors in the estimates of tonnage and grade of the mined material as well as errors in the millÆs assessment of the material processed. Keeping these errors small and unbiased is an important aspect of an efficient operation whose primary goal is to derive maximum benefit from the exploitation of the mineral resource.These fluctuations in periodic reconciliations can also mask subtle but economically important problems which may take years to identify and resolve. Such problems can result from a poorly-conceived model of the mineralisation which affects both the spatial distribution of the ore as well as the tonnage - grade distribution over the range of cut-off grades. Poorly conceived models of the mineral resources and ore distribution can arise as a result of insufficient and inadequate?drilling and sampling of the mineralisation, inappropriate?application of geological?constraints in the estimation process and the use of inappropriate methods to estimate the block grade distribution. This paper presents three case studies from gold and copper mining operations, two of which experienced significant problems with their mine to mill reconciliations over extended periods of time. For the gold mine in case study 1, sampling problems were ultimately considered to be the main cause of the poor reconciliations between grade control predictions and the mill which persisted over a period of 18 months. In addition, incorrect application of resource modelling methods contributed significantly to a mismatching of the mill capacity with the mine at the beginning of operations. For the underground copper mine in case study 2, a change in the approach taken to resource modelling brought marked improvements in ore definition and more accurate predictions of ore grade and better production forecasts.The third case study describes the background to the expansion of production to exploit a large tonnage of lower-grade stockwork mineralisation in an open pit gold mine. Several years of favourable Mine to Mill reconciliation data from the mining and processing of higher grade and lower grade stockwork styles of gold mineralisation provided the confidence in the approach to grade control to support the expansion plans during a period of low gold prices.The paper is intended to complement the discussion of mineral resource estimation methods and risks in Section 6.1.3 of the Mine ManagersÆ Handbook to be published by the Australasian Institute of Mining and Metallurgy (Schofield, 2012).CITATION:Schofield, N A, Moore, J and Carswell, J T, 2012. Mine to mill reconciliation - Three case studies, in Proceedings International Mine Management 2012, pp 161-172 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 20, 2012

By Richmond A

Like many industries the coal mining industry has, since the beginning of this century, undergone many changes. Technological advances and the increasing demand for fossil fuels have introduced new mining methods and techniques which allow the extraction of thicker and deeper coal seams at higher rates of production. Most new methods of mining (or for that matter any other processes) introduce problems which the engineers of the industry are expected to face and resolve. Unfortunately, spontaneous combustion has plagued the coal mining industry since the first attempts to mine coal, and is no doubt partly responsible for the reputation that coal mining is a hazardous industry. The financial loss and toll of human lives due to the occurrence of spontaneous combustion of coal in coal mines is enormous, if not incalculable. Its occurrence today is less likely to claim lives, due to both improved methods of working and in the detection of spontaneous combustion sites.

Jan 1, 1983

Comparatively recent Tasmanian legisla tion established a series of rigid control standards for environmental protection just as ma spectacular expansion of the mining industry was nearing completion. Upgrading existing protection to obtain the necessary licence to operate under these new regulations required further major works and involved a considerable outlay of non- productive capital at a time when escalating costs and falling metal prices were straining economic efficiencies to the limit. Late in 1974 a major environmental protection scheme was commissioned by the Electrolytic Zinc Company of Australasia Limited at Rosebery on the West Coast of Tasmania. This 4 million dollar project was specifically developed by the Company ahead of and to meet the new standards for control of total effluents discharged from its zinc-lead -copper-pyrites mine and concentrator.

Jan 1, 1977

By T Kojovic

"The index A*b, determined from the Julius Kruttschnitt Mineral Research Centre (JKMRC) drop weight tester (DWT) results, has become well-known in the mining industry as a reliable measure of ore hardness in impact or crushing, having the inferred units of t/kWh. This index evolved from a long history of comminution studies at the JKMRC, including the development of the now superseded JKTech twin-pendulum, the industry standard JK Drop Weight Tester (JKDWT) and the faster alterative JKMRC rotary breakage tester (JKRBT). A reduced version of the DWT, the semi-autogenous grinding mill comminution test (SMC test®), also provides estimates of the A*b though the testing of only one particle size at five specific energies. Experimental determination of A*b using the above devices/tests requires samples, with sufficient mass, to be sent to designated laboratories, registered to conduct such tests. This protocol is fine for bankable and commercial testing, where material characterisation data is used in conjunction with machine specific data in modelling and simulation, and power based calculations. However, for comparative testing, where results are required at the time of sampling (eg for plant troubleshooting or spot-surveys), or for rapid ranking of geometallurgical samples, these existing tests simply do not provide a timely, viable and cost-effective solution. In order to address this critical void in the realm of comparative testing, a new device has been developed, exploiting a central feature of single particle impact testing – that the A*b can be reliably estimated using one precise low energy test. This device, for which a patent is currently pending, called the HIT (Hardness Index Tester), has been precision engineered to allow users to break narrowly sized fragments at a set specific energy, in a safe and easy manner. The manufacturing materials have been chosen carefully to ensure compatibility with the intended use and portability to any site, whilst minimising cost. The device is supplied with a novel quality assurance / quality control (QA/QC) feature, to ensure that the targeted potential energy is consistently delivered. The product from the HIT breakage test can be quickly sized using a single screen to determine the mass per cent undersize, from which the A*b index is calculated directly at site – eliminating the need to send the raw data off-site for analysis. On presized fragments, a single test using 20 fragments takes less than five minutes to complete, and the results are immediately available. The HIT is currently being tested at a major mining laboratory in the US and the results to date have proved it can deliver on all fronts. This paper describes the new prototype device, which offers users a low cost in-house mechanism for estimating the A*b at any mine site, with potential applications on fragments up to 25 mm from drill core, blast chip rejects or the grinding circuit feed. It also outlines the results of field tests carried out by an objective third party mining group and compares the results with those from current industry standard tests conducted on the same material.Citation:Kojovic, T, 2016. HIT - a Portable Field Device for Rapid Testing at Site, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 9–16 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

Improved roof control in high deformation tailgate environments has been achieved over the last decade through development of stiffer and increased capacity standing support products. æThe CanÆ is one such development, being a steel cylinder containing a weak cementitious fill, designed to essentially fold in upon itself whilst maintaining strength. A laboratory study to better define the relative load contributions of the steel cylinder and fill, the confining interaction between these components and most importantly, the potential impact of varying the steel and/or fill properties is described. This would enable the support engineer to ædial-upÆ the desired strength and stiffness properties and optimise the standing support design with respect to load capacity, stiffness, weight (handling) and cost. Design curves to optimise strength based on steel casing thickness, fill strength (confined and unconfined) and æCanÆ geometry were established. Scaled-down (one-third) samples were used in the test program and found to adequately reflect the loading behaviour of full-scale versions, thereby providing significantly greater scope for further product development at less expense compared with testing full-scale products.

Jan 1, 2005

By J Walshe, G Duclaux, L A. Fisher, R Hough, J S. Cleverley, M F. Gazley

Characterisation of hydrothermal gold systems across multiple scales is increasingly important for our understanding of ore deposit genesis and for targeting new mineralisation. Published work on multiscale mineral system exploration focuses either on applying a single technique across scales or on incorporating a series of techniques across a limited scale range. Typically, these studiesÆ spatial scales vary from crustal to deposit-scale and have successfully linked the distribution and shape of major orebodies to fault systems or varying lithostratigraphy. But, is this scale small enough to answer fundamental questions about the relative timing, processes interactions and mechanisms involved in the formation of ore deposits? We illustrate the potential of a deposit to microscale study, using the Plutonic Gold Mine in Western Australia as an example, to better understand hydrothermal gold systems. Using an integrated approach combining lithological and alteration logs, various geochemical data set, meso- to microscale structural and textural observations and spatial data assimilation, we have revisited the fundamental processes involved in the formation of this significant gold deposit.CITATION:Duclaux, G, Hough, R, Gazley, M F, Fisher, L A, Walshe, J and Cleverley, J S, 2013. A multiscale approach to hydrothermal gold systems - unravelling mineralisation processes at the Plutonic Gold Mine, in Proceedings World Gold 2013 , pp 95-98 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By A Takahashi, Y Uchisawa, M Hayashi, T Watanabe, M Susa

Owing to the deterioration of iron ore, the Al2O3 concentration in iron ore increases, and thus it is important to investigate the effect of increment in Al2O3 concentration on the microstructures of iron ore sinters. During the sintering process, a melt is present in the sinter for only a few minutes, and therefore the microstructure of the sinter doesn’t reach thermodynamic equilibrium. Nevertheless, the formation process of the microstructures can be interpreted and predicted to some extent from the equilibrium phase diagram. This study investigated the liquidus isotherm in the CaO-SiO2-Fe2O3- 5 mass% Al2O3 system at 1240°C in air and the phase equilibria of silico-ferrite of calcium and aluminium (denoted by SFCA) and SFCA-I by XRD (X-ray diffraction analysis) and electron probe micro analyzer (EPMA). The following results were obtained: 1. The ferrite melt region with a high Fe2O3 concentration shifts to the lower Fe2O3 side than the liquidus isotherm in the CaO-SiO2-Fe2O3 system. 2. The compositional region of SFCA extends in the CaOꞏ3Fe2O3-4CaOꞏ3SiO2 direction than the silico-ferrite of calcium (denoted by SFC) composition region with a 0 mass% Al2O3. 3. SFCA-I is observed in the present system, which suggests that the increment in the Al2O3 concentration contributes to the stability of SFCA-I. These results imply that an increment in Al2O3 concentration in iron ore leads to a decrement in the volume fraction of the bonding phase and that the fraction of the SFCA phase increases, and those of 2CaOꞏSiO2 and slag phases decrease in the bonging phase. The SFCA-I phase is also precipitated from the slag with an Al2O3 concentration around 5 mass%.

Jun 19, 2024

By D Morgan, D Sato, B Lumsden, S Senanayake

Laboratory flotation tests on fresh cyclone overflow samples are a useful tool to troubleshoot and indeed to improve plant performance; however, reproducibility between laboratory flotation test and plant performance is important for interpretation of the laboratory tests and hence their usefulness. Chemical reproducibility can be achieved with the addition of the required reagents; however, reproducing the physics of forces and energy in a 5 L cell compared to a 50 000 L plant cell or a 500 000 L plant cell is not generally studied or discussed. For some tests such as collector evaluation the physics of the flotation process may not be critical, but for some evaluations in the laboratory, it can be important.All flotation plants suffer from losses of valuable <20 µm mineral. Selective mineral aggregation has long been recommended to improve the poor flotation recovery of <20 µm sulfide minerals; however, successfully testing any type of selective sulfide mineral aggregation’s effect on flotation recovery in the laboratory on practical plant samples requires reproducing plant cell physics. The energy input per litre and the forces in a laboratory cell are vastly different to a plant cell. Reproducibility between laboratory and plant tests requires that these differences be minimised. The physics of the laboratory flotation cell is particularly important when fine mineral aggregation tests are carried out.This paper outlines a modified laboratory aggregation and flotation method that closely reproduces plant performance in a laboratory test.CITATION:Sato, D, Lumsden, B, Senanayake, S and Morgan, D, 2014. Development of a laboratory flotation method to test plant mineral aggregation, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 173–178 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By T J. Callaghan

The Avebury nickel mine in Western Tasmania is a disseminated nickel sulfide deposit hosted in intensely metasomatised Cambrian ultramafic resulting from later Devonian granite related hydrothermal activity.Variable metasomatism of the ultramafic has formed two distinct gangue mineral assemblages. Less metasomatised ultramafic is comprised of fine grained black antigorite with minor disseminated chromite, magnetite and pentlandite. Intensely metasomatised ultramafic is altered to a pale grey or green, coarsely crystalline tremolite/actinolite and diopside assemblage with minor magnetite, chromite and sulfides. Both gangue mineral assemblages are frequently intermixed in ore grade mineralisation.The bimodal gangue of either serpentinite or metasomatised ultramafic presents challenges to drilling, mining, resource estimation and mineral processing as they possess very different physical properties. Mineralised serpentinite has a mean bulk density of 2.8 g/cc and the ultramafic skarn a mean bulk density of 3.2 g/cc. Physically, the ultramafic skarn is hard to break percussively creating difficulties in the crushing circuit and reducing mine development rates. However, it is non-abrasive and grinds readily, resulting in increased diamond drilling rates and increased mill throughput. Conversely the serpentinite gangue is softer and breaks easily resulting in accelerated development rates and crushing circuit throughput. However, its fibrous nature reduces grinding efficiency, increasing bond work indices and reducing diamond drilling rates.Predicting the ratio of serpentinised to metasomatised ultramafic is possible through use of the resource blockmodel, assisting mine scheduling, predicting mill throughput rates, energy consumption and grade control drilling rates.CITATION:Callaghan, T J, 2017. Challenges of bi-modal gangue mineralogy in mining geology, in Proceedings Tenth International Mining Geology Conference 2017, pp 23–26 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By Roberts T, Firth B. A

A series of flotation experiments was carried out to study the interaction between the parameters of pulp density (mass per cent of solids in feed slurry) and frother addition (on the basis of solid mass feed rate). It was found that certain combinations of pulp density and frother additions caused large losses in yield. The interactive effect of these parameters can be primarily attributed to the total amount of frother added per unit of water. Consequently it is suggested that frother additions be made on the basis of water flow rate. As frother addition increased, in terms of the amount of frother per unit of water, yield increased rapidly but above an addition rate of about 10 g/tone it reached a plateau. Such results correlated well with qualitative visual observations of changes in bubble size and dispersion, with increasing levels of frother addition.

Jan 1, 1984

My roots span four generations. My great grandfather, Christian Frederick Fisher, along with twenty-one others was drowned in the New Australasian mine disaster at Creswick in Victoria in 1882. My grandfather, also named Christian Frederick Fisher, escaped and then followed a career of shaft sinking for large companies and operating small mines (very unprofitably according to my father) when funds allowed. My father, an excellent practical mining and mechanical engineer, was also a small miner and my early entry into the industry was, like many before me, very basic. My introductions to the business end of a No. 4 shovel, drilling with hand steel and later with jack hammers without the benefit of airlegs, feeding heavy cordwood to hungry boilers and felling trees for mine timber soon dispelled any illusions I had that mining was a bed of roses.Before it became well known I knew "Life was not meant to be easy".In a family-owned small gold mine in a remote part of Cape York Peninsula in far north Queensland I was fortunate in obtaining an excellent grounding in reef and deep alluvial mining. Operating in vertical and underlie shafts the variable ground conditions often required close timbering. Steam pumps were used underground and steam winders for hoisting.The complete absence of municipal or government infrastructure in this remote mining field threw responsibility on each mine operator to be self-sufficient, and responsible for mine development and installation of crushing and milling equipment, accommodation and water supply. Conditions, although harsh, were acceptable in the 1930s, and fostered great self-reliance.The first crushing from our Black Cat Mine in 1935 returned nearly 200 oz from 10 tons of ore. Gold was then worth $13 an ounce compared to about $400 an ounce today; but in those depression years of the 1930s our operation was profitable.This basic education not only returned dividends when confronted with difficult mining problems, but created a deep respect for the miners who develop the small mines and who continue to contribute to the industry today, often under difficult conditions.Australia and mining are synonymous. The industry has been immortalised by the famous historian, Professor Geoffrey Blainey, in his book "The Rush that Never Ended".Initial gold discoveries were concealed and exploration was frowned upon by authority as being disruptive to early rural development. But with the discovery of gold in the Bathurst area of New South Wales by Hargreaves in 1851, the rush to the gold fields began followed by an influx of migrants. The traumatic effect on industry and society that followed, created the pattern of the love-hate relationship that at times became temporarily submerged, but is so evident today.In the harsh economic climate of the 19th century with low wages and no welfare, the opportunity to wrest riches from the earth was literally "rushed" by the adventurous, the poor, the rich, people from all walks of life. Pressures developed on preFederation Governments to provide law, order and infrastructure to the rushes that have never ended.

Jan 1, 1984

By See G. T

Bentonites and fuller's earths from seven localities in N.S.W. have been analysed with respect to occurrence, mineralogy and physical properties and areas for future prospecting have been indicated.INTRODUCTIONThe rapid expansion of Australian industry in the postwar years has been accompanied by an ever increasing demand for fuller's earth and bentonite, but in New South Wales at least the demand has been met principally by imports. However, some local and generally inferior active earths have been won to blend with imported materials to reduce costs. The important discovery of the widespread distribution of bentonite clays in the Northern Coal Measures, made recently by Grim (Booker, 1956), has givenimpetus to the further search for material comparable in quality to the imported active earths.Bentonite may be defined as a highly plastic clay, generally possessing swelling properties, composed essentially of montmorillonite and derived from the alteration of volcanic ash. Fuller's earth refers to any clay which, with or without chemical treatment, is capable of decolourizing mineral or vegetable oils and is, therefore of economic value. Montmorillonite is the active component of most fuller's earths, though palygorskite-, halloysite- and even kaolinite-rich clays have been used.Previous literature related to the New South Wales deposits has been confined to general descriptions and little technical data beyond an occasional chemical analysIs have been available. Bentonites and fuller's earths from seven...

Jan 1, 1959

By D Craw

The Macraes gold deposit is located in a low angle NE dipping (~15¦) shear zone, the Hyde Macraes Shear Zone (HMSZ) cutting greenschist facies metasediments of the Otago Schist. The shear zone is host to large volumes of mineralised schist and relatively sparse quartz veins. Early in the development of this through going shear the schist experienced an episode of hydro fracturing and fluid redistribution. As a result, presently exposed schists within the Intrashear sequence are pervaded by localised swarms of quartz filled pure extension and extensional shear fractures hosting goldscheelite mineralization. The swarms comprise networks or æstockworksÆ of veins that strike NE, are subvertical and form subperpendicular to the shear zone fabric. Vein frequency across strike is typically ~1 m-1, with most veins five to ten centimetres thick and vertically continuous for up to ~20 m. Many of the veins show delicately banded internal textures that are parallel to the vein margins. These bands/lamina indicate incremental growth and are defined by a variation in grain size or alternatively by thin slivers of wallrock schist, though typically uncommon. The majority of veins are overprinted by a weak plastic deformation, although primary structures are largely preserved. This deformation has produced subgrain structures, migration of grain boundaries with sutured margins and undulose extinction of grains. These microstructural observations possibly indicate that temperatures were around 300¦C during stockwork vein formation. In general, the mode of brittle failure that developed the stockwork veins can be directly related to lithological variation. The geometry of stockwork veins indicate that local vertical shortening and extension occurred in the Intrashear sequence of the HMSZ synkinematically with thrusting. Localised extension was mainly parallel to the structural trend; that is, it took place perpendicular to the direction of inferred thrusting. The development of lateral ramps most likely gave rise to extension in parts of the shear zone during continuous shortening to form swarms of stockwork veins.

Jan 1, 2004

By R Morrison, R Dunn

In many mineral processing operations, the reported production figures for an accounting period may not make the best use of available data. While most of the mathematical approaches, such as check-in/check-out, mass balancing, used in effective metallurgical accounting strategies are well understood, the sources and magnitude of measurement errors generally are not. As part of the æAMIRA P754-Metal Accounting and ReconciliationÆ project, a study was undertaken at the Northparkes copper/gold concentrator near Parkes, New South Wales to examine the data used in their concentrator metallurgical accounting system. This paper summarises the results of a detailed examination of the mass measurement systems around the concentrator as well as the primary sampling system used for grade estimation. The goal of this work was to develop practical techniques to quantify the error (ie both accuracy and precision) of the measured metal accounting information. With this information, statistical confidence levels for this data can then be calculated. If the errors are small, the effect of error in each piece of measured data can then be propagated to other calculated production figures such as recovery and feed grade using a statistical technique called æthe propagation of errorÆ.

Jan 1, 2007

By Y Zhang, Z Zhao

The green production of the steelmaking process has urgent requirements for fluorine-free fluxes. In this article, a new solid waste-based slagging flux was applied in the external dephosphorisation test of low silicon hot metal to replace the traditional fluorite-lime dephosphorisation slag. The results showed that under laboratory conditions, the new flux was utilised for smelting low-silicon molten iron with a phosphorus content of 0.10~0.13 wt per cent, the temperature of the molten iron was 1350°C and the slag amount was controlled at 2 per cent. Within ten minutes of smelting, the dephosphorisation rate of the molten iron reached more than 50 per cent. When making slag with new flux, the slag melting time was about 40 seconds and the P2O5 content in the final slag was higher than 8 wt per cent. In the industrial test of a 150 t molten iron ladle, under the same molten iron conditions, an out-of-furnace dephosphorisation test was conducted in the Kambara Reactor (KR) process. The flux material consumption per ton of steel was 8~10 kg. Within 15 minutes of smelting, the dephosphorisation rate of the molten iron was about 30 per cent. During flux slag making, the slag melting time was about three minutes and the P2O5 content in the final slag was higher than 6 wt per cent. This new solid waste-based flux has significant cost advantages and outof- furnace dephosphorisation effects and is expected to become the benchmark for a new generation of fluorine-free steelmaking fluxes.

Aug 21, 2024

By C D. Rose

"The primary objective of this paper is to demonstrate a different approach to predicting and verifying mechanical sampling system precision. Early in the year 2011 an experiment was conducted to evaluate the sampling precision being obtained by a three-stage falling-stream mechanical sampling system for coal owned and operated by Peabody Energy. This system collects samples from lots averaging approximately 14000 t being loaded onto rail cars at a flow rate averaging about 9000 t/h. In phase 1 of the experiment, a total of 60 increments were collected in a two day period at preassigned intervals using a cross-belt sampler located on a conveyor belt feeding a silo upstream of the sampling system under evaluation. Coal variability parameters were calculated from the resulting laboratory analysis data using the gauge-invariant fractal model developed by the author.Estimates of precision of the three-stage system as a function of the number of increments were calculated using the variability parameters determined in phase 1. In phase 2 of the experiment, duplicate samples of 30 lots of coal were taken by the three-stage sampling system, enabling calculations of the precision being achieved by the system. Phase 2 precision estimates are in reasonable agreement with those of phase 1. Conclusions drawn from the experiment include the following: Experimental variograms or the equivalent correlograms are essential in understanding sampling issues and for designing a sampling system to meet specific precision requirements. Consensus coal sampling standards provided by ISO and ASTM may be improved by treating all stages of a mechanical sampling system as æsamplingÆ rather than considering downstream sampling stages as æsample preparationÆ, to be treated in a separate part of the document. The coal industry would profit from use of methodology for routinely monitoring the overall measurement precision and the precision of the individual components of measurement: sampling, sample preparation and laboratory testing. This would not only give necessary credence to the measurement results but would also no doubt, lead to more efficient sampling system designs.CITATION:Rose, C D, 2012. Evaluation of precision being obtained by a three-stage sampling system for coal, in Proceedings Sampling 2012, pp 115-124 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 21, 2012

By K R. Vining, T E. Norgate

A study was carried out to compare the environmental impacts of the two major iron ore agglomeration processes, sintering and pelletising, using life cycle assessment (LCA) methodology. The following agglomeration processing routes, with the fuel options shown, were investigated:sintering with combined natural gas/coke breeze or charcoal as fuel, grate-kiln pelletising with combined natural gas/coke breeze as fuel, and straight-grate pelletising with combined natural gas/coke breeze as fuel. Inventory data for each process derived from the literature, and in some instances supplemented by additional simulations and calculations, were used in the study and the environmental impact categories considered were gross energy requirement (GER), global warming potential (GWP) and acidification potential (AP). The results of the study showed that the GER, GWP and AP for a sinter plant are higher than those for a pellet plant for the same amount of metallic iron in the agglomerated products. These results are partly due to higher consumption of solid fuel and flux in the sintering process. However, it should be pointed out that the study only compared substantially fluxed sinters with acid pellets that may require additional flux (and hence potentially more greenhouse gases emissions) to be a balanced blast furnace feedstock. Extending the LCA to the blast furnace process stage was beyond the scope of the current study. Within the sinter plant, the sintering stage itself is the largest contributor to the GER, GWP and AP. In the case of pellet plant, the pellet induration stage is the largest contributor to the various environmental impacts. The GER and GWP of a straight-grate pellet plant are marginally higher than those of a grate-kiln pellet plant due to the higher electrical power required by the straight grate system. The substitution of coke breeze with charcoal in the sintering process results in an increase in GER but a decrease in GWP. However, a substantial proportion of the GER is derived from renewable sources (wood), resulting in a decrease in the non-renewable components of this environmental impact. Given the source of the inventory data and the assumptions and approximations made in carrying out the LCAs, it is emphasised that the results presented in this paper should be considered as indicative rather than as definitive results for the two iron ore agglomeration processing routes considered.

Jan 1, 2006

Xstrata CopperÆs Mount Isa Copper Operations is located in mineral rich north-west Queensland and is one of the largest sources of copper in the world. This world-class underground operation is planned to produce over 6.6 million tonnes of copper ore in 2007 from the X41 and Enterprise Mines. With an underground mining history of over 50 years and underground reserves of over 83 million tonnes at 2.6 per cent copper, mine planning for the future becomes an exciting challenge for the technical team due to the older nature of certain areas. The 1100 Orebody of the X41 mine was one of the first places that copper mining occurred, with its discovery in 1953 - 1954 and mining commencing in the 1960s. Sublevel open stoping mining methods have been employed since that time as the means of extraction, using a primary-secondary sequence to maximise stope turnaround time. Large Transverse Pillars within the 1100 orebody were not mined out in order to provide access for ventilation, power, orepasses and other services. The Panel Pillar, 4180XC and 4010XC pillars are three such Transverse Pillars in the 1100 orebody that will be mined as a final retreat. This paper discusses the technical challenges and issues associated with the extraction of Q390 stope, one of the stopes located in the Panel Pillar, and the design solutions to overcome these issues. Managing the exposure of backfilled stopes of variable fill strength, ensuring the stability of the crown, stope walls and drawpoints, managing vertical openings, re-establishing service networks, and stope filling are the critical issues given consideration for the final design of Q390 stope and other such stopes within a Transverse Pillar. Communication and coordination between the different departments in the mine are essential for the necessary work to be completed in a timely manner to bring pillar stopes into production.

Jan 1, 2007

By S Tyrrell, B Jackson, K Matson

Northern Star Resources Limited Jundee Gold Mine in Western Australia operates a comminution circuit that consists of a primary crusher, 3.85 MW semi-autogenous grinding (SAG) mill, 1.8 MW ball mill and pebble recycle crusher. In 2017, a secondary crushing circuit was installed to remove the SAG mill throughput bottleneck and increase production of highly competent underground ore from 1.35 to a minimum of 1.7 Mt/a.This paper discusses the findings from the trial phase, the circuit design, project delivery, site optimisation, and the plant performance.CITATION:Matson, K, Tyrrell, S and Jackson, B, 2018. The application of secondary crushing at the Jundee gold mine, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 485–496 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018