Search Documents

By F M. Senda

This paper highlights strategies used at the Barrick operated Kibali Gold Mine (KGM) to improve the drilling accuracy and blasting effectiveness for longhole open stoping. The mine currently uses Solo DL421 for the required stope drilling and has experienced an average deviation of 10 per cent. Strategies are raised to eliminate or at least mitigate the adverse effects of blasthole deviation and the impact of blasting induced effect at the stope faces including the stope crown. The integration of deviation trends in the design would allow the actual blastholes to be established within their required positions to then facilitate a proper energy distribution with the eventual production blasting. The implementation of stope undercutting reduces the hole length from 35 m to 30 m which in return decreases blasthole deviation by 3 per cent. Another strategy adopted to improve the drilling accuracy is to slow down the penetration rate with the use of several operating approaches, including 135 MPa percussion pressure, 65 rev/sec rotation speed and 17 MPa feed pressure. To this penetration rate, a constant k factor is applied to increase the rate when the bedding inclination is less than 45° from the horizontal or when the hole length is under 10 m. This reduces deviation by a further 4 per cent. Where the rock mass is highly jointed it is advised to use the average penetration rate over the entire length of the hole. Furthermore, the paper shows the effect of deviation on the blasting results through a prediction of fragmentation blasting model optimised with reduced deviation and highlights the effect of presplit mining and timing delay on the blasting effectiveness. Although the size pattern increases with deviation, a strategy pertaining to timing delay with blasting would be to align to the work of Grant (1990) where the optimum hole to hole delay is found to be between 7–10 ms/m of spacing, while the optimum delay between adjacent ring varied between 110–160 ms. Stabilisation of crowns and wings will perform with the implementation of presplit blasting.

Mar 29, 2023

By D K. Weatherley, G R. Ballantyne, S Ali, M Yahyaei, M S. Powell

This paper explores development of a novel ore characterisation method for the precise measurement of practical minimum comminution energy. A monolayer of particles with a narrow size distribution is broken using a precision rolls crusher (PRC); an ore characterisation device developed to overcome the shortcomings of conventional tests. For energy measurement, PRC uses two shaftmounted rotary torque transducers. These transducers acquire precise torque and angular speed data in response to the load applied to the rotating shafts during breakage events, which is converted into energy. The test progressively crushes feed particles down to final product size in many controlled breakage stages. The generation of fines in each breakage stage is then plotted as a function of input energy. The inverse of the gradient of this plot provides the size specific energy (SSE) in kWh/t of material generated below a predefined marker size; -75 μm in this case. The PRC has potential to evolve as a geometallurgical ore characterisation test—it is simple, fast, requires small sample mass (200–300 g), covers a wide feed particle size range (10 mm to 115 µm), and provides ideal SSE measurements that can be used for the calibration of on-site production equipment.

Aug 24, 2022

By T M. Brettell, D Sidea

The CSA Mine is located in Cobar, New South Wales and is operated by Glencore. Large scale underground production started from 1965, with zinc, lead, silver and copper extracted in the past. The current operations focus on copper, with a silver co-product.From 2014 to 2016, Cobar Management Pty Ltd (CMPL) undertook a major capital project to upgrade the primary ventilation system at the CSA Mine. This involved the development of ten raises using full-face raise boring from surface to a depth of 1450 m. The total length of the raises was approximately 2500 m. Geotechnical conditions were identified as a key project risk during the early planning stages of the project. Timely quantification of the geotechnical risks was required to minimise project delays and cost overruns. Geotechnical investigations were planned and conducted for each raise prior to pilot drilling and full-face back reaming.Nine of the ten raises had final wall camera and laser baseline surveys completed following full-face reaming. The surveys were conducted progressively, allowing ongoing back analysis and calibration of geotechnical evaluations as the project advanced.This paper presents the design and planning process of the raise bored excavations. It details the geotechnical investigation work undertaken to mitigate the geotechnical risks and the challenges and learnings from the project including the benefits of close collaboration between the parties involved.CITATION:Sidea, D and Brettell, T M, 2017. The CSA ventilation upgrade – geotechnical challenges and learnings, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 341–352 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

To help meet the challenge of mine finding at the start of the 21st century, the exploration geophysicist will have at his command a powerful range of tools, some new, some improved, and some which already exist today but are as yet little used. Remote sensing, using satellite and aircraft-based multi-spectral scanners, will provide the means for routinely mapping the surface distribution of certain carbonate rocks, clay and ferrous alteration minerals, based on the analysis of solar reflectance spectra. Time and emission-spectral resolved laser-induced fluorescence will likewise map the distribution of certain ore and pathfinder minerals, as well as certain skarn zones, all potentially related to ore deposits. The GPS (Global Positioning System), based on 18 orbitting satellites, will provide a universal, three dimensional, all weather navigation system which will completely supplant all existing aerial navigation systems, and greatly facilitate aerial surveying and automated processing and presentation of the data. Aeromagnetic gradiometer measurements will provide higher geometric resolution which will yield better definition of individual geological units. Multi-method ground geophysical surveys will be greatly expedited through the use of portable microcomputer-based, multi-sensor instruments. These instruments will interface with other intelligent devices for automated processing, presentation and interpretation of the ground field data. Borehole geophysics will come into more general use, both for at-hole measurements, especially using active nuclear techniques for grade determination, and for remote detection using a variety of electrical, magnetic, seismic and other methods.

Jan 1, 1986

By M Davies, G Theletsane, A H. Gray

Recovery of gold from gold ores has been driven by the available technology and its configuration in the process plant flow sheet.Conventional practice in test work programs has the ore being ground fine (to 106 or 75 microns) to ensure liberation ahead of leaching or flotation. This paper identifies that, in many cases, gold and gold sulfide carriers will liberate and be recovered to a concentrate at much coarser sizes.There is an exponential increase in energy consumption relative to particle size reduction. This impact becomes extreme when comparing crushing a product to 1 mm against grinding to 75?microns.The resultant reduction in energy consumption when liberating and separating at 1 mm or coarser compared to grinding to 75 microns can be in the order of 15 kWh/t or 60 per cent of energy in the comminution circuit.Recovery of free gold and gold sulfide carriers by preconcentration (using continuous gravity devices such as the InLine Pressure Jig), combined with flotation of the fine gold and gold carriers, can result in significant power savings.There are multiple locations within the flow sheet that can be targeted using this process, including recovery in the cyclone underflow of existing plants, preconcentration ahead of the plant or complete greenfield, low-energy process plants designed from first principles based on data from a Gekko developed test work regime.We will describe the process of defining mineralogy in the laboratory and the decision-making process through to actual applications in the field.Several examples will be provided, including a South African Witwatersrand gold ore, several Australian gold ores and others, indicating the benefits of this process and where it has been brought to commercial reality.CITATION:Gray, A H, Davies, M and Theletsane, G, 2014. Coarse liberation and recovery of free gold and gold sulfide carriers for energy reduction in process plants, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 117–128 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By K G. Harding, A Osman, A du Toit, F K. Crundwell, C M. Sheridan

"Most mineral processing plants have high water requirements for their operational activities. These plants often function in an environment where water is becoming increasingly scarce. An increase in population will result in an increased demand for water; potentially beyond the limits of supply and hence increased competition for the resource. In South Africa, Gauteng and the North West Province are likely to be first to experience a shortage of potable water.In order to avoid a water crisis, efforts must be made to ensure the effective management of water resources and the minimisation of wastage. Hydrometallurgical plants have a responsibility to society and the environment to operate in a sustainable manner - reducing their water requirements will certainly assist towards developing a sustainable footprint.This project improved site water management by: surveying the potable water and storm water systems with a view to assessing the current water accountability and determining methods to improve accountability determining the monthly and yearly water balance for the site and presenting it in the form of a water balance sheet drawing up an input-output and operational model in accordance with the Minerals Council of AustraliaÆs æWater Accounting Framework for the Minerals IndustryÆ calculating the water footprints of the refinery identifying ways in which water savings could be achieved recommending management systems for water usage monitoring.This work was conducted in South Africa. The value of this work lies in that it established the current baseline and assisted in developing management systems that can reduce water usage sustainably.CITATION:Osman, A, Crundwell, F K, Harding, K G, Sheridan, C M and du Toit, A, 2013. Water accountability and efficiency at a base metals refinery, in Proceedings Water in Mining 2013, pp 277-286 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 26, 2013

By P Dunn

Following civil war in Sierra Leone, London Mining Plc obtained the mining license in 2006 and commenced activity to redevelop the Marampa mining and processing operations. The Sierra Leone Marampa mine is a brownfield development effort, having been operated by a few companies since the 1930s until low iron ore prices forced closure. Peak production of the preceding operations was approximately 2.5 Mt/a in the 1960s. There are two virgin ore deposits of interest for development as well as a resource comprised of tailings accumulated from previous operations. The Marampa tailings operation (Phase 1a) is being implemented first with a 1.8 Mt/a plant producing 66 per cent Fe sinter feed, expandable to 3.6 Mt/a in a Phase 1b. The first phase is currently under construction with start-up expected in the third quarter of 2011. Further expansion (Phase 2) that includes the development of the virgin deposits is currently under prefeasibility study and targets a final 16 Mt/a concentrate production. Outotec partnered with London Mining to develop the magnetic separation flow sheet using SLon VPHGMS machines to process the Marampa tailings (haematite) material. The flow sheet development process started with sample characterisation and detailed parametric investigations to evaluate SLon performance. The final flow sheet configuration, including expected circuit recoveries and concentrate quality, demonstrates the performance of the SLon VPHGMS circuit for iron ore tailings.

Jul 11, 2011

By J P. Evert

Didipio gold-copper mine operation is situated in the island of Luzon, approximately 270 km north of Manila in the Philippines, in an area of high seasonal rainfall. The hydrogeological water flow model implied that there would be high connectivity between regional structures and underground operations. This model predicted that underground mine groundwater inflows were expected to quickly rise as the decline progressed to a peak of 510 L/s. Designing a capital pump station to deal with 510 L/s has its own challenges, however developing the decline down to the required level, always dealing with 300 L/s of water and constructing the pump station is extremely challenging and required a robust water management plan and mine design. When dealing with expected high volumes of water, underground mine design and scheduling plays a key role in protecting electrical infrastructure, equipment, secondary pumps, and the decline from flooding. A good drainage system and controlled dewatering plan is essential for safety and progress. This paper details the dewatering techniques and mine designs required to accomplish decline development with high water inflows as used in the Didipio project. It will describe the learnings and outcomes that are achievable with a flexible design, as new structures are mapped, and water intersections are increased. It also highlights the potential for adaptability in mine planning to provide evolving improvements or to evade problems that are expected from the constant reconciliation of data recorded during development.

Mar 29, 2023

By M Bloss, B Roberts

BHP Billiton Olympic Dam required a well-tested software product suitable for strategic optimisation and scheduling of options for a potential underground mining project. The company has a standard software package called Blasor® that is used for open pit optimisation of complex deposits such as iron ore, copper-gold-uranium and silver-lead-zinc. It applies a mixed integer programming formulation (MIP) to produce conceptual pushback designs and an optimised pushback sequence. Schedules can then be run on the resulting mine designs. Existing pushback designs can also be imported into the model and an optimum schedule generated. One of the key advantages of Blasor is that multiple strategic mine schedules can be quickly generated according to the various scenarios, options and constraints that are being investigated.It was realised that Blasor, if carefully configured, could be adapted for use in underground planning. The concept of using Blasor as an optimiser for underground strategic scenarios is to represent the underground stope and development data in the form and structure of an open pit mine. In simple terms, underground stoping areas are modelled in the form of pushbacks (phases) with vertical walls. The phase dependency tools in Blasor are used to link mine blocks and their access development drives. These underground phases are imported into the optimiser. Artificial block models are constructed using stope design tonnage and grade data at various fixed cut-offs. A variable cut-off grade model has also been developed using a method of parcels to represent each cut-off grade increment.So far, this approach has been successfully used to investigate the optimum stope design cut-off for various strategic options, the economic potential of a series of mining and processing configurations and to provide guidance on the optimum sequence for developing and mining the various stoping blocks in the resource. Examination of the results has highlighted the most suitable development paths for more detailed study.CITATION:Roberts, B and Bloss, M, 2014. Adaptation of an open pit optimiser for underground strategic planning, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 249–256 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By Z Tong, M Gao, X Wang

In response to the need for improved magnetic separators for beneficiation of fine grained iron ores that have been finely ground to liberate the iron minerals from the gangue, a series of high efficiency wet drum permanent magnetic separators (T-GCT) has been developed by Maanshan Tiangong Technology Co Ltd. These magnetic separators have high efficiency for separating superfine strongly magnetic minerals and the ability to produce high-grade concentrates with high recovery. They are ideal replacements for conventional drum magnetic separators, especially for treating superfine particles.

Jan 1, 2009

The continuous casting of zinc alloys has been of fundamental importance for many years in the production of a number of products, including sheet for architectural applications, battery cans for dry cells and wire for metallising. The intrinsic benefits of continuous casting, including efficiency and high tonnage capability, uniformity of metallurgical structure and properties, and absence of voids and other defects, have contributed to the success of these products. Less well known, but of growing importance, is the more recent application of continuous casting technology to the production of zinc alloy bar stock products, including bearing stock, machining bar stock, forging stock and cathodic protection anodes. A wide range of zinc alloys are now continuously cast in a variety of cross sectional shapes and sizes to suit the diverse characteristics of these products. Of particular significance are the introduction of hollow zinc-aluminum bearing stock, and the availability of zinc alloy machining bar stock for hydraulic applications and for producing prototypes of zinc alloy pressure die castings. In addition to the traditional benefits, continuous casting provides special properties which are important in the application of these bar stock products. The list of successful applications of continuously cast zinc alloy bar stock is growing rapidly, and the market potential for resultant new zinc applications appears to be significant.

Jan 1, 1993

By M Armony, J F. C L Costa, J C. Koppe

Linear kriging methods fail to estimate local grades and local reserves for highly skewed variables due to three reasons: it uses only part of the available data information, it has no physical principles associated with the mathematical proceedings to minimise the problems, and it works with continuous variables while data are discrete because of the limited precision of any equipment. The techniques commonly used up to now to solve the highly skewed variables estimation problems were unsuccessful, unless mathematical rigor is abandoned. Even the method of multiple indicator kriging is not satisfactory. This paper presents a new framework, the field parametric geostatistics (FPG) that transforms noisy variograms into well-behaved variograms and justifies mathematically empirical procedures commonly used, as trimming or capping arbitrarily very high values. The method, when applied to non-skewed variables, yields similar results to classic kriging. The methodology is illustrated in a case study at a gold deposit in Brazil, and compared to results obtained by usual techniques.

Sep 26, 2011

By P B. Hills

A simple algebraic method of aligning large scale underground excavations such as a crusher station or workshop or indeed any large cavern or mine layout to the optimal stress condition is outlined. The method uses the stress transformation law to determine how the component stresses vary as the stress tensor is rotated around its axis. The aim is to define the orientations at which the maximum and minimum horizontal stresses occur such that the excavation can be aligned with its long axis paralleling the trend of the maximum horizontal stress leading to the minimum potential for overstressing of the side walls. The physical environment in which the stress field is acting is unchanged. At the design location, the trend and plunge of the major principal stress is unchanged. However, the coordinate system by which the location of the stress field is described is arbitrary and the stress transformation law allows that coordinate system to be rotated to a more convenient orientation and for the component stresses to be calculated within the alterative coordinate system. The stress field is typically described in terms of normal and shear stresses aligned to a north–south, east–west, vertical, coordinate system. In this scenario, there are two orientations in the 360° horizontal plane defined by the coordinate system where the horizontal normal stresses are equal, and at 45° to those orientations, two orientations where they diverge to the maximum extent. Those orientations of maximum divergence correspond to the trend of the maximum and minimum horizontal stresses, usually designated σH and σh, and that is what the algebraic manipulation seeks to determine. This technique is a first pass assessment which relies on a knowledge of the full stress tensor. It is not a replacement for numerical modelling or detailed design, but a tool to guide planning.

Nov 29, 2022

By S Barrow, D Kent

Controlling the access of equipment, and people, has become more critical over the last few years for improving productivity and to meet safety responsibilities imposed by legislated obligations to have safety management systems. Hence Mine Site Technologies (MST) has spent the last three years completing the development of the tagging system to meet the mining industryÆs requirements, particularly streamlining access control. The basic tagging system tracks active Tags carried by personnel, or attached to vehicles and equipment, within underground zones. These Tags are detected (read) by Beacons placed strategically throughout the mine. As a Tag, or Tags, go past a Beacon they are read and the information transmitted back to the main database PC. This allows the current whereabouts of personnel and equipment to be known, as well as the history of their movements. The objectives of implementing the TRACKER Tagging System at Oaky No 1 Coal Mine were to: maintain a count of personnel inbye a particular point, and can alarm when a pre-set number is reached (eg the limit imposed by availability of SCSRÆs, etc); maintain a count of vehicles (and vehicle type) inbye a point, and can alarm if when a pre-set number is reached (eg when rated diesel units exceeds the limit for the ventilation present in that zone); manage the vehicle fleet, by keeping track of various vehicles underground better control and dispatch management of the equipment is achieved; keep track of equipment, knowing the location of equipment (such as forks, baskets, pumps, fans, etc) where last used or stored will minimise the risk of losing gear and assist in keeping inventory to a minimum; and locate personnel in emergency situations, by placing read Beacons throughout the mine the location of all personnel can be known in real time so that in the event of an emergency, their withdrawal can be monitored.

Jan 1, 2005

By E Niva

The IsaMillÖ is challenging the way that plants are designed and operated. This paper challenges existing designs of concentrator flow sheets, particularly focusing on magnetite circuits.   From what has started out as a small scale ultra fine grinding mill in the pharmaceutical and pigment industries, it has been redesigned and improved upon for mineral processing, and has been the mainstay of fine grinding applications for over ten years. These applications have required energy efficient grinding to succeed, and have been predominately in the base metals industry.   Further development of the IsaMillÖ has now resulted in the machines being able to treat larger tonnages, with higher capacity motors. This development, along with the introduction of purpose designed ceramic media, has allowed the mill to treat courser feed sizes. At the same time, the mill still offers highly efficient grinding, and has enabled it to be operated in coarser tertiary and secondary grinding applications.   The acceptance of the mill in coarser applications, predominately in base metals and PGM applications, has enabled the IsaMillÖ to be a serious contender for beneficiation in other minerals. One such application is the potential for IsaMillsÖ to be part of magnetite flow sheets, which are being considered in Australia to meet the growing iron demand of China. The high energy efficiency of the IsaMillÖ compared to conventional technologies, as well as the smaller infrastructure requirements, provides a great opportunity to reduce the power intensity of magnetite circuits.   This paper will examine the use of IsaMillÖ technology in conventional grinding applications, including recent testwork in a primary grinding base metal circuit, as well as testwork on magnetite ore comparing a lab scale IsaMillÖ with a lab scale Tower Mill.   The growing demand for minerals over the next decade, coupled with higher energy cost, will result in energy efficient technology, such as the IsaMillÖ, being included in standard circuit design.

Jan 1, 2008

By G N. Phillips

Global annual gold production has been remarkably constant over the last decade at ~2500 t/a3. The major producers today are China (annual production over 350 t and rising), Australia (250 t), USA (240 t), Russia (200 t) and South Africa (190 t and falling); these figures are representative of recent years but approximate. Demand from jewellery, investment, industrial and dental uses has been in excess of mine production for the last decade, by approximately 1000 t/a.Ongoing exploration is the life-blood for gold mining, and more so than for many other metals. Explorers consider sovereign risk, security, labour costs, commercial terms, land availability and inherent geologic prospectivity to determine where to focus their activities. Exploration success over the last decade has been shared by established major producers like Australia, Canada and USA, several countries in West Africa, and many parts of the Pacific margin. Although gold-only deposits have dominated world gold production historically, the gold-plus types, especially copper-gold, are becoming more important.Australia experienced a major period of exploration success from 1979 that has led to annual gold production rising from 17 t in 1979 to 250 - 300 t/a recently. Today, Australia has economic demonstrated resources of over 9000 t Au, which has risen progressively from 220 t in 1979. The majority of production has come from gold-only deposits in the Yilgarn craton in the southern half of Western Australia, but there are a few large Proterozoic deposits in central Australia including Olympic Dam, Telfer and Starra, which are mostly gold-plus types with copper and gold. Large goldfields in the younger host rocks of eastern Australia include the gold-only deposits of Victoria and North Queensland, and gold-plus deposits of New South Wales.CITATION:Phillips, G N, 2013. Australian and global setting for gold in 2013, in Proceedings World Gold 2013 , pp 15-22 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By Y Yang, J Skrypniuk

The Jinfeng mine is Sino Gold's flagship project and is the second largest gold mine in China. Sino Gold Limited (SGL) holds 82 per cent equity in the Sino-Foreign joint venture Sino Guizhou Jinfeng Mining Limited (SGJML) with a Chinese partner. Jinfeng is located in a relatively remote site in southwestern Guizhou province. The orebody is considered to be the largest known Carlin type deposit in China. Jinfeng Plant has the world's third largest BIOX« bacterial oxidation facilities (790 t/d), treating highly refractory concentrate generated from crushing, semi-autogenous grinding (SAG) and ball milling and bulk sulfide flotation operations. The Jinfeng Plant construction started in February 2005, commissioning was completed in April 2007, and commercial gold production was achieved in September 2007. This paper describes the successful operations of Jinfeng Plant over the last two years. The key events of the project development are described, from the project background and process design, through to the commissioning and achieving design mill throughput of 3600 t/d resulting 180 000 ounces of gold per year. Process aspects of the BIOX« and carbon-in-leach (CIL) operations over the last two years are discussed which illustrate a very high BIOX« oxidation rate (more that 97 per cent) and excellent CIL recovery (more than 96 per cent). The management of the Jinfeng plant CIL tailings detoxification and filtration is described, and Jinfeng has became the first BIOX« processing plant to have achieved dry stacking of detoxified and pressure filtered CIL tailings. Current efforts to recover cyanide from CIL detoxified solution and the achievement of a zero discharge site water balance are also introduced. Many improvement projects have been made over the last two years which have culminated in a 15 per cent increase in mill throughput over the design and BIOX« CIL recovery increasing from 92.5 per cent to 96 per cent. Significant operating cost reductions from lowered of acid, lime and cyanide usage through process modifications and technical innovations are discussed.

Jan 1, 2009

By E N. Sparg, O D. A Deuchar, F Needham

Decline shafts are an attractive option to both new and existing mining operations where there is a need to access an inclined orebody deposit via on-reef development so as to generate a return in the shortest possible time. There are many different technologies that are available to transport men, material and rock in incline shafts. This paper focuses on the applicability of two hoisting technologies for decline shafts, namely endless and direct rope systems. The pros and cons of each system are reviewed. A common concern with direct rope haulage systems is the possibility of generating slack rope during deceleration. This paper illustrates the issues involved in designing a system so as to avoid the possibility of slack rope. In conclusion, the key factors relevant to the selection of endless or direct rope haulages for a particular decline application are reviewed. The paper is a joint submission by FFE Minerals-Vecor and Qualter Hall UK.

Jan 1, 2005

The concept of Extreme Gravity is the latest in a series of innovations that has seen a re-introduction of gravity recovery systems into the milling operations of most gold mines. Traditionally, most gold milling circuits are designed around flotation and cyanidation requirements, with the gravity circuit being fit in where possible. Extreme Gravity takes the novel approach of optimising the circuit, in order to maximise recovery by gravity. In some cases gravity systems can achieve high enough recoveries to eliminate the need for chemical systems such as cyanidation or flotation. There are many advantages of such a system including low capital cost, reduced permitting, improved cash flows and much reduced environmental issues. There are a number of plants currently in operation which utilise this new methodology. The Muzhievo project has been an example of a recent turn key success achieving recoveries from 85 - 90 per cent. The details of this project are examined as a case study.

Jan 1, 2000

By M Norbert, C Bennett

The Legacy Way Tunnel was constructed from Toowong to Kelvin Grove in Brisbane, and is the first large-scale underground excavation in the Bunya Phyllite in Brisbane. The Legacy Way Tunnel is 4.3 km in length, comprising two mainline tunnels excavated by a tunnel boring machine (TBM) with 46 connecting passages excavated between the mainline tunnels for egress provision and services. The Legacy Way Tunnel passes through two geological formations, the Bunya Phyllite and the Neranleigh Fernvale Beds. The Bunya Phyllite is the dominant formation of the Legacy Way Tunnel, extending for three quarters of the tunnel prior to intersecting the Normanby Fault Zone (NFZ) and the Neranleigh Fernvale Beds. The NFZ forms the contact between the two formations as part of the Brisbane Metamorphics, which underlies the majority of Brisbane City. The development of the geological model and the understanding of the ground’s reaction to tunnelling was an iterative process. The tender phase investigation data has been supplemented with additional design phase investigation boreholes, geophysics and walk overs. Aerial photograph interpretation coupled with borehole data allowed the development of the domains along the length of the tunnel. Early excavations for the spoil conveyor tunnel and borehole data from subsurface instrumentation installation provided the first construction phase data followed by the commencement of tunnel boring machine (TBM) excavation. Routine cutterhead inspections coupled with ongoing reviews of the predicted geology resulted in clear response triggers to selection of segment types while detailed inspections in passage locations provide the initial classifications for segment removals.CITATION:Bennett, C and Norbert, M, 2014. Tunnelling within the Bunya Phyllite of Legacy Way, Brisbane, Queensland, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 131–140 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014