Search Documents

By Kennedy G. L

Operating experience with the pilot Lurgi carbonization plant at Morwell showed that under conventional operating conditions, although the thermal efficiency of the plant was very' high, the physical quality of the char produced was extremely poor. By variation of operating conditions to produce the slow drying rate developed by the laboratory research at the University of Melbourne, an improvement in the size of the char was achieved. A similar approach in the carbonization stage where severe breakage of the briquettes still occurred was not possible due to insufficient control over the heating in this stage. Theoretical analysis of the heat exchange process has shown that severe heating of the briquettes entering the carbonizer is a characteristic of the Lurgi system and cannot be controlled by modified operation. The plant has been closed down for reconstruction of the heating system to enable it to be used to produce hard char.INTRODUCTIONAn experimental carbonization plant was operated at the Morwell Works of the 'Gas and Fuel Corporation from November 1958 until July 1959. This plant was built as a pilot plant by the Corporation to designs supplied by the Lurgi Gesellschaft fur Warmetechnik and had the nominal capacity to carbonize 25 tons of brown coal briquettes and to produce 11 tons of char per day. The briquettes were supplied from the· normal production of the Yallourn briquette factory and the 2t in. I-type briquette was the largest size which the plant could handle.This carbonization plant represents the intermediate stage of development between the laboratory research at the University of Melbourne and the commercial production of hard char as a metallurgical fuel. It is intended in the first place for the study of the technical problems in the handling and...

Jan 1, 1960

By C M. Hall

We report 40Ar/39Ar ages for adularia and illite from veins and wall rocks at the Waihi and Favona deposits, in the Waihi district. One sample of vein adularia from the Favona deposit yielded a plateau age of 6.04 ¦ 0.06 (la) Ma, and two samples of vein adularia from the Waihi deposit yielded plateau ages of 6.17 ¦ 0.03 and 6.17 ¦ 0.09 Ma. Two samples of wall rock adularia from the Waihi deposit yielded plateau ages of 6.07 ¦ 0.06 and 6.08 ¦ 0.03 Ma. Adularia ages overlap at the 2s level, and we do not consider them to be significantly different. Two samples of illite from wall rocks at Favona have total gas ages of 5.66 ¦ 0.04 and 5.65 ¦ 0.04 Ma, and retention ages of 6.57 ¦ 0.04 and 6.61 ¦ 0.04 Ma, whereas one sample of vein illite yielded a total gas age of 5.29 ¦ 0.17 Ma, and a retention age of 6.26 ¦ 0.19 Ma. The total gas ages of illite are minimum ages that are equivalent to conventional K/Ar analyses, whereas retention ages of illite are maximum ages. Although interpretation of the illite data is complicated, the adularia results strongly suggest that the Waihi and Favona deposits formed contemporaneously in the same fossil geothermal system at 6.0 to 6.1 Ma.

Jan 1, 2003

In a previous paper the author showed that silver considerably delayed the recrystallisation of lead after cold work. The effect of antimony on the rate of recrystallisation of distorted lead was studied next, and the experiments performed, and the results obtained, are described in this paper. Electrolytic lead was used as a standard of comparison.It was also used to make the lead antimony alloys.This electrolytic lead contained 0.0005% total impurities.It was prepared from commercial lead by fire refining, followed by electrolysis and finally by vacuum casting. The process was described in the previous paper and the description need not be repeated here. PREPARATION OF LEAD - ANTIMONY ALLOYS.The steps taken to procure pure antimony are outlined in the appendix. To make the lead antimony alloys a mother alloy was prepared thus:-A quantity of the antimony (it was received in the powdered form) was placed in a pyrex glass tube, which was closed at one end. The antimony was washed with hot hydrochloric acid (1: 1), then with more dilute acid, then with distilled water, and finally with absolute alcohol; it was dried by warming and evacu,ating the tube. This should leave the antimony more nearly free from surface oxides.The amount of antimony was determined by weighing quickly; the appropriate amount of vacuum-cast electrolytic *Research Fellow, Dept. of Metallurgy, University of Melbourne.

Jan 1, 1936

The optimisation of a mining operation requires precise ore grade control, metallurgical accounting, and laboratory sampling protocols, which are implemented by using accurate and flawless sampling systems. Good sampling practices, and sampling technologies in these fields have been historically poor and too many existing sampling systems available on the market are flawed in many ways. This is mainly the result of a poor understanding of the Sampling Theory, and the natural result of international standards on sampling that fail to present the Sampling Theory in a logical way, that still promote non-probabilistic sampling, and that fail to address the important details that make a correct sampling system. Many standards barely mention the Sampling Theory in appendices when it should be clearly the main body of a reliable standard on sampling. As a result, many standards show only little expertise in the Sampling Theory. Conventional statistics should only be a scientific tool for the Sampling Theory to reach its height, which has always been well understood by its creators. Conventional statistics can indeed be addressed in appendices of standards in sampling, but not the other way around. Until the Sampling Theory is recognised as the main body of a standard on sampling, incorrect sampling technologies will plague the market, and make it impossible for mining operations to optimise their mining and metallurgical processes. This paper makes a short list of correct new sampling technologies that have been created with respect to the principles taught in the Sampling Theory. Also, suggestions are presented to create better international standards on sampling, which would provide a stronger incentive for manufacturers to build correct sampling systems, and for engineering firms to install only sampling systems that respect the rules of sampling correctness listed in the Sampling Theory.

Jan 1, 2004

By P Meehan, R McAree, Z Guan

Equipment maintenance is 30 - 50 per cent of the operating costs for a typical mining company. While this is substantial, its importance is beyond its significance as a cost heading. Modern mining requires large amounts of investment in capital infrastructure and equipment to produce a product sold at a low unit cost. To stay competitive, such a business has to focus on full realisation of its capital investment, ie sustained production at high levels. Maintenance plays an essential role in achieving this goal. Mining companies typically use a mix of breakdown or corrective maintenance, planned maintenance, and some condition-based maintenance. The share of breakdown maintenance has been coming down through more effective planned maintenance and better condition monitoring tools. Planned or preventive maintenance (PM) is playing an increasingly important role in todayÆs mining maintenance. This is the suite of inspection and repair/replacement actions performed at scheduled time intervals as part of a preplanned activity. The activities are scheduled well in advance and, usually, the current wear-state of the machine is irrelevant. For example, the replacement of a major gear may have been planned 18 months in advance; replacement is carried out when the time comes regardless of the actual condition of the gear. The PM costs are significant and include direct cost of parts and labour as well as the opportunity cost of lost production while the machine is under maintenance. It is important to identify the optimum PM effort because over-maintenance should be avoided as much as under-maintenance. A new concept called severity-based maintenance is introduced in this paper. We have seen that measuring equipment ageing in mining merely by counting the engine hours is a very imprecise way of planning and scheduling maintenance because the damage accumulated in one hour varies enormously from operator to operator and with changing pit conditions. We recommend continuous monitoring of duty on all major equipment. This is feasible without having to fit out the machine with an army of sensors because most of the physical sensors required by dutymeters are already installed and maintained as part of the existing performance monitors. While the investment is modest, the potential benefits are huge and can be grouped under three headings:Immediate benefits will come from providing operators with direct feedback on the effect of their behaviour on machine health and training them to use this feedback to correct their operating style. The equipment can operate closer to the limits of capacity, producing more without unduly sacrificing the availability by monitoring and controlling the severity of the operation, ie the duty on the machine. Longer term benefits accrue from establishing correlations between actual time to failure data and measured equipment duty and using these correlations to optimise maintenance effort as well as planning new equipment purchases and warranty conditions.

Jan 1, 2002

Deposits of the Reefton Goldfield, West Coast, New Zealand, are hosted on N-NE striking, upright folds of the Greenland Group. High-grade quartz lodes are hosted on axial planar shears, typically have short strike lengths, and form shoots that pitch steeply on the hosting shears. Deposits within the field area of a detailed structural study share these characteristics. Field mapping and microstructural analysis have demonstrated that the Greenland Group was affected by a multideformational sequence. Gold mineralisation is hosted on shears axial planar to the F2 folds, but occurred during a subsequent deformation event (D4). Deformation during D4 resulted from N-NE directed shortening, near parallel to the trend of the F2 folds. This event produced F4 kink folds that were accommodated by layer parallel slip on S2 parallel shears, gold mineralisation during D4 being confined to the dilational hinges of F4 kink folds. The semi-brittle nature of D4 allowed the formation of stockwork veining and disseminated mineralisation within the F4 hinge zones. Most deposits within the goldfield are similar to those within the field area, and are interpreted to have been mineralised during D4. The two largest known deposits within the goldfield, however, are distinct. The Blackwater Deposit, striking parallel to the hosting folds, has a combined strike length of 1 km. The Globe-Progress Deposit is hosted on an E-W striking discordant shear in which a brittle zone of disseminated mineralisation encompasses high-grade quartz lodes. The characteristics that distiguish the Globe and Blackwater deposits may be due to formation before and after D4 respectively. Detailed field mapping in the vicinity of known deposits throughout the goldfield will further refine the relationships between the F2 folds, later deformations and the localisation of ore deposits. Additional mapping may also help constrain the position, orientation and extent of additional orebodies.

Jan 1, 2001

By Met M, Worner H. K

In pursuance of the investigation into the influence of various elements on the properties of lead during the past year, the effect of several elements on the creep rate of commercially pure lead has been investigated; a standard initial stress of 500 lb. per sq. in. having been adopted for comparison purposes. Other work which has been carried out indicates that the relative results of creep tests may be altered by varying the applied stress, but this aspect of the problem will need to await further investigations for itscomplete elucidation. The results obtained with dilute tellurium alloys are considered sufficiently interesting, and in some respects are so extraordinary, as to warrant publicatiorr at this stage.n must be realised however that, since the results obtained appear to be at variance with those said to have been obtained in practice and those previously published, the present investigation can only be considered as a contribution to our knowledge of the general problem.Consequently it is not considered advisable or necessary to offer detailed explanation of the results given. In fact, some features of the tests about to be described will need further investigation before an adequate explanation is possible.

Jan 1, 1936

The main factors which influence disposal of mine waste under New Zealand conditions are identified and discussed: namely, geological conditions which produce soft weather-sensitive waste, wet and cold winters which affect productivity in such waste, elevated seismicity which affects stability and the need for water rights which involve public participation. The waste disposal scheme for the Martha Hill Project is described, thereby illustrating how these factors influence the planning of a current mine strippings and tailings disposal scheme.

Jan 1, 1986

By K L. Brown, J L. Mauk

Sulfide-rich scale occurs in steam and water lines at the Ohaaki geothennal field,Taupo Volcanic Zone, New Zealand. Precious metals show very high concentrations around areas ofpressure reduction (Au 15500 ppm, Ag 68800 ppm). Pyrrhotite dominates at the orifice plate due to low PH2s1PH2 conditions. Sulfide mineralogy in the scales is consistent with alteration mineralogy of the reservoir rocks. Separated steam then produces a mainly pyrite/magnetite mineralogy, with lesser chalcopyrite, where textures reflect high flow rates and high levels of supersaturation. This study outlines the effect that pressure and subsequent temperature decreases have on the mineralogy, chemistry and textures of sulfide scales.

Jan 1, 1998

Open cut mining of the Black Rock chalcocite ore started in 1963. A ground movement monitoring programme was commencing in the early stages of mining when signs of instabilityof the western wall became apparent. Eventually 100.000 cu vd, of overburden Were removed beyond the rim of the western wall in an attempt to stabilize the slope. Subsequent decpenlug and mining till the final batter angle of 45 resulted in deterioration and mining was stopped 38 ft short in the ulltimte design deplh of 520 ft.Investigations showed that the geology of the western wall , was a major factor in the instability of this wall. A block jointed model was made 10 illustrate some of the pehomena observed. Quallatative agreement was found between the model deformation and the field measurements obtained.The results of the monitoring programme clearly show the value of this work In respect to the conlrol of the mining operatIon...

Jan 1, 1968

A field method combining solvent extraction and paper partition chromatography permits a simple and rapid semiquantitative estimation of gold in siliceous, argillaceous and sulphide ores. The method will facilitate the eyaluation of prospect samples in which the gold is too fine for separation by panning.Ethyl alcohol-hydrobromic acid mixtures are suitable for chromatographic development of the gold complex, and give clear reproducible definition of the gold zone. Substitution of commercial "methylated spirits" for the ethyl alcohol gives equally good definition, improving the potential of the method for field use.A batch of six samples in the range of 0·5 to 5·0 dwt/ton can be completed in two hours. The range may be extended by simple modification to higher or lower values.INTRODUCTIONIn a chromatographic method described previously (Lever 1958, Nevill and Lever 1959), gold from a standard volume of ore clamped between -plate glass was extracted by aqua regia on to the paper. After cautious drying the chromatogram was developed by an ethyl acetate-nitric acid-water mixture and gold was identified by spraying with stannous chloride solution. Sensitivity of the method in the low range was poor. The brown line obtained in the 1-3 dw/j ton range, caused by movement of gold in the reduced form, was not considered to be a satisfactory confirmation of the presence of gold. It was felt that the method would be improved by using a more elegant extraction and applying developing conditions which would produce a well defined purple line at all gold values. Iron was a limiting factor, and a method of eliminating its interference was needed.The method now developed overcomes these shortcomings, and gives a reliable result with a purple line for assay values of 0·5 dwtjton and over. Gold is dissolved from an...

Jan 1, 1964

The Peelwood district of New South Wales is located some 65 miles south of Bathutst on the Tuena-Crookwell road. A number of occurrences of lead-zinc-copper ore are known from this district but only three mines, Peelwood, Cordillera and Mt. Costigan, have achieved any significant production. The purpose of the paper is to describe the mineral composition of sulphide ores from these three localities.HISTORYNo published information on the geology of the Peelwood area is available. Came (1899) reports that, at the time of cessation of mining operations in 1888, the Peelwood mine had produced some 600 tons of copper metal and regulus, the Cordillera mine had yielded 9000 tons of ore at the recoverable grade of 2·5 per cent Pb, 2·5 per cent Cu, 90z/ton Ag and 1 dwtjto:p. Au, but that no production figures were available from Mt. Costigan. No further work was carried out on these properties until 1951 when the Electrolytic Zinc Company of Australasia instigated a programme of geological mapping and exploratory diamond drilling (Whitten, unpublished data, 1953). The Peelwood district was recently mapped by Mutton (unpublished thesis, 1960) from whom the following geological summary account was taken.GENERAL GEOLOGYAll rocks in the Peelwood area belong to a series of interbedded fine grained sediments and volcanics that are thought...

Jan 1, 1961

Uranium ore at Sleisbeck, N.T., occurs as lenticular bodies associated with zones of bleached carbonized schists lying between walls of closely folded quartzite. The ore consists mainly of uranium micas with Borne pitchblende.INTRODUCTIONThe Sleisbeck uranium prospect is about 70 miles E. of Pine Creek, and 160 miles S.E. of Darwin (Fig. 1). The prospect consists of a well-defined, E.-W. trending line of hills, about I! miles long. The line is composed of 3 major hills called the Eastern, Central and Western hills, with minor interconnecting hills and outcrops (Fig. 2).

Jan 1, 1955

By M Rafty, A Markham, S Atkinson, M Heyting

Over recent years there has been a significant increase in the number of miners in the Pilbara region of Western Australia targeting channel iron deposits (CID) located in valleys, intersected by ephemeral creeks and below the groundwater table. The falling iron ore price has triggered a drive to reduce cost and maximise yield. Creek diversions provide an opportunity to maximise the utilisation of orebodies and extend the life-of-mine.Creek diversions that are required during mining operations to access ore and provide flood protection have historically been constructed as uniform engineered channels designed primarily for flow conveyance while minimising earthworks costs; however, the design of diversions becomes more complex when they are required to function in a similar way to the existing creek system during operations and remain stable during more extreme events than would typically occur following mine closure, in accordance with current regulatory guidance. The design specifications for closure are often more rigorous than the operational phase, and could incur significant additional cost to implement retrospectively if not planned and designed upfront.The complexity of diversion design depends on site specific factors such as: the size of the creek to be diverted; hydrology; corridor restrictions; geomorphology; hydrogeology; geology; environmental and heritage values; potential impacts and the risk to operations and environment. The complex interactions of these factors must be well understood and hydraulic modelling undertaken to characterise the existing creek system, demonstrate the diversions, provide adequate flood protection during operations, and can function in a similar way to the existing system following mine closure. This paper presents key design considerations for Pilbara creek diversions, operational and closure requirements, mine planning considerations, risks, cost saving opportunities, and the benefits of an integrated approach to design.CITATION:S Atkinson, A Markham, M Rafty and M Heyting, 2017. ‘Back to the future’ – resilience in historical context and implications for the future, in Proceedings Iron Ore 2017, pp 367–374 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By B Murphy, A Uliana, P STrgio de Oliveira, G Ara·jo de Souza Franco, T Miettinen

Outotec has performed numerous research and development projects and various surveys in the study of reverse iron ore flotation. Over the past four years their TankCell-70 and TankCell-160 flotation cells at the Germano concentrator of Samarco in Brazil were extensively surveyed. These surveys have revealed some extreme operating conditions in reverse iron ore flotation and are the subject of this paper. Some of the findings include large variations in the content of solids in the various flotation stages. At the bottom of the cleaner cells, the content of solids by weight reached over 60 per cent, whereas at the bottom of the scavenger cell this was less than 50 per cent. Froth carry rates were also significantly different in the various flotation stages. In the case of coarse material, the scavenger cells operated at a froth carry rate of over 40 t/h.m2. With fine material, however, froth carry rates of less than 10 t/h.m2 were measured. High froth carry rates caused significant changes in the residence times at Samarco. In the rougher cells, the fifth cell had more than double the residence time of the first cell. This was even more pronounced with the scavenger cells, where the second cell had more than triple the residence time of the first cell. High froth carry rates also caused losses in iron recovery. As a consequence of such findings, it appears that different rules apply in the sizing of reverse flotation circuits compared to direct flotation circuits. Different operating parameters (mixing intensities and air flow rates) must also be used in the rougher, cleaner and scavenger cells in order to optimise the metallurgical performance. Outotec has also been working on a number of new technologies aimed at improving the metallurgical performance of iron ore reverse flotation circuits by increasing froth carry rate and decreasing fine iron entrainment.CITATION:Miettinen, T, Uliana, A, Ara·jo de Souza Franco, G, STrgio de Oliveira, P and Murphy, B, 2013. TankCell flotation at SamarcoÆs Germano concentrators, in Proceedings Iron Ore 2013 , pp 441-444 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By M Eggers, H Baxter

This paper discusses the geotechnical condition of bedding shears and small- and large-scale faults and shears in Archean banded iron formation (BIF) bedrock, based on observations of core and televiewer images. Information that can be collected includes the orientation of defects, infill thickness, strength and material type, defect shape and surface roughness.The spacing and continuity of bedding shears may be critical to slope design where performance is structurally controlled with bedding dipping out of a wall. The intensity of development of the bedding shear is a useful indicator of the amount of shearing a bedding surface has been subjected to. This can allow for engineering judgement to be used in adopting peak or residual shear strengths along defect surfaces when developing the design.The spacing and continuity of bedding shears may also contribute to the blockiness and degradation of a rock mass where the structural orientation is otherwise favourable. Additionally the condition, thickness and strength of infill of major fault structures can affect slope design and performance, depending on orientation.Comparison of the condition of structures observed in core with the corresponding in situ televiewer image has been made to assess what characteristics are most accurately captured by each technique and whether the additional information gathered from using the televiewer technique is justified by the cost. The question of whether the data collected by a televiewer is sufficient to ultimately replace the need for core is considered.CITATION:Baxter, H and Eggers, M, 2013. Fault and shear characterisation in archean banded iron formation bedrock - a comparison between core and televiewer data collection techniques, in Proceedings Iron Ore 2013 , pp 47-56 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By N M. Caira

The North Arm of Sulawesi hosts numerous gold and base metal occurrences. Compilation and analysis of geological, tectonic, geochemical and isotopic age date data collected over the past six years on the central part of this region have resulted in the definition of 184 prospects and mineral occurrences of various styles occurring in diverse geological settings representing varying tectonic environments and erosional levels. Mineralisation of the following styles have been recognised: porphyry Cu-Au; porphyry-related gold and base metal veins; high-sulphidation Cu-Au-As; low-sulphidation epithermal Au; hydrothermal breccias; and sediment-hosted Au mineralisation. Clusters of occurrences/prospects form mineralised districts representative of magmatic systems with characteristics determined by the tectonic environment prevailing during formation and the subsequent level of exposure by erosion. Distinctly different Miocene and Pliocene porphyry systems are now recognised whilst most of the remaining epithermal mineralisation is thought to be Pliocene or later. The central North Arm of Sulawesi is composed of a Miocene magmatic island arc that is built on an Early Tertiary basement of predominantly oceanic basaltic rocks and overprinted by a Pliocene magmatic arc. A structural fabric dominated by SSE arc-normal and ESE arc-parallel faults was established during the Miocene under a dextral wrench regime and intersections of these major fault sets are favoured sites for Miocene porphyry Cu-Au mineralisation. Strong dextral tension caused by the collision of the Sula Platform, at the close of the Miocene, led to arc-parallel rifting. Sinistral reactivation of the major Miocene structures in the Pliocene led to further rifting, and ENE-dilation. Pliocene intrusions and related mineralisation exploit these dilatant settings. Miocene porphyry Cu-Au mineralisation occurs where late-Miocene quartz diorite stocks have intruded the margins of earlier Miocene plutons of intermediate composition. Porphyry centres have associated peripheral base metal veins, and skarns. Overprinting of porphyry vein sets by epithermal veins is common. Sediment-hosted gold mineralisation occurs in calcareous sediments associated with the Miocene arc. Remnants of the Pliocene volcanic arc, comprised of dacite volcanics, intrusions and voluminous pyroclastics, dominate the south coast and host porphyry Cu-Au, high sulphidation Cu-Au-As deposits, low-sulphidation epithermal Au veins and disseminated gold mineralisation. In some prospects, mineralised sinters are preserved adjacent to vein systems and deeper mineralised stockworks. Diatremes are common and large caldera structures have been identified. Pliocene stocks and porphyry dyke swarms penetrate the main central and northern parts of the Miocene- arc introducing additional porphyry Cu-Au, base metal hydrothermal breccias and low-sulphidation gold veins. Rapid uplift and erosion has resulted in a highly variable preservation of styles of mineralisation adding further diversity within the mineralised districts and telescoping within deposits.

Jan 1, 1999

By B Xiao, J Yang, H Chen

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Tuwu-Yandong Cu deposit, located in the East Tianshan mountains in the eastern section of the Central Asian Orogenic Belt, is the largest and economically most important porphyry Cu deposit in Xinjiang, China. It contains ~3 Mt of copper at an average grade of 0.46 per cent Cu and 0.2 g/t Au, with significant amounts of Mo and Ag. The deposit is mainly hosted in the Carboniferous Qi’eshan Group and plagiogranite porphyry, and is controlled by faults that are east–west-, north-west- and north-east-trending. Ore minerals in the Tuwu-Yandong deposit are dominated by pyrite, chalcopyrite and molybdenite, with minor bornite, chalcocite, magnetite, sphalerite and galena. Gangue minerals are mainly composed of quartz, sericite, chlorite, epidote, anhydrite, gypsum, muscovite, biotite, phosphorite, sphene, dolomite, actinolite, barite, albite and calcite. Based on the megascopic and microscopic textural relationships and mineral assemblages, five stages of hydrothermal alteration and hypogene mineralisation are recognized in the Tuwu-Yandong Cu deposit: the potassic stage, propylitic stage, phyllic stage, late veins stage and supergene stage. Most of the copper was deposited during the phyllic stage, along with less molybdenite.CITATION:Xiao, B, Chen, H, Wang, Y and Yang, J, 2015. Geology, mineralisation and alteration of the Tuwu-Yandong porphyry Cu deposit, north-west China, in Proceedings PACRIM 2015 Congress, pp 641–644 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Pound J. R

THIS mine, which is the property of the S. and M. Syndicate, London, is located at Moina, in North-West Tasmania, 18 miles from Stavertorr railway station and 36 miles from Devonport. There are metalled roads from both of these places, and, althoughhilly, these are good for team or motor traffic. Mails and passengers are provided for by a tri-weekly coach service from Sheffield, a railway town, distant 23 miles. The Moina mining field is situated on a main spur between the Forth and Iris Rivers, andat an elevation ranging from about 500 ft. above sea-level at the Forth River to 2400 ft. at the All Nations mine. The elevation at the mine office of the S. and M. mine is 1900 ft. The average annual rainfall, as recorded for the past eight years, is. 68 in.This inclildes, however, a couple of years during which the rainfall was much above normal, and taken over a longer period 60 in. would be nearer the average.

Jan 1, 1919

By F H. S dosSantos, R L. C Santos

The main objective of this work was to develop, at a laboratory scale, a process for treating residues from the settling stage of water treatment so as to remove and recover the aluminium as sulphate. The chemical analysis of residues from different water treatment plants indicated that the aluminium content varied from 15 to 20 per cent w/w. By using the appropriate experimental conditions, it was found to be possible to leach most of the aluminium content. The pH value of the recovered water was suitable for it to be recycled to the water treatment process and the residue appears to be suitable as raw material for bricks. The process developed contributes to the sustainability of the water treatment process.

Jan 1, 2002