Search Documents

By J. S. FINLAY

OPERATING a "muck stick" never appealed to me. It always seemed a terrible waste of energy to "put rocks in the box" by hand-particularly when my own personal energy was involved. But during the past forty years, there have been periods-more or less extended when I was compelled, against my finer instincts, to muck or quit eating. For about the same length of time, I have devised schemes to make mucking faster and more painless. There was always something mechanically wrong with these designs-too many;" parts to wear out and need replacement, and excessive cost incidental to a complicated mechanism. The idea of a shovel unit comprised of a single, rigid assembly which would roll from a digging to dumping position solved the problem of simplicity and durability. Ingersoll-Rand's utility engine provided a splendid power plant, small enough and powerful enough for the job. In the machine finally developed, known as the Eimco-Finlay loader, roller chains are preferred to gears for power trans-

Jan 1, 1935

By H. I. Aaronson, C. Wells

Configurations of ferrite crystals have been found in a plain carbon steel which appear to have resulted from the nucleation of new ferrite crystals at the interphase boundaries of previously formed crystals despite the high carbon concentrations which necessarily develop at these boundaries. This phenomenon has been termed sympathetic nucleation. An attempt has been made to reconcile the occurrence of sympathetic nu-cleation with current nucleation theory. THIS investigation is one of a series on the formation of proeutectoid ferrite from austenite. From the viewpoint of chemical composition, this reaction consists of the nucleation and diffusional growth of crystals of carbon-poor ferrite within a matrix of carbon-rich austenite. The austenite adjacent to the austenite-ferrite boundaries will be greatly enriched in carbon, approximately to the value of the y/(a + y) equilibrium curve or its metastable extrapolation at the temperature of transformation. Those areas of austenite appreciably farther removed from the growing ferrite, on the other hand, will be relatively unaltered in composition, especially at the earlier stages of transformation. Since rates of nucleation are considered to decrease exponentially with decreasing supersaturation,' the frequency with which ferrite nuclei appear at austenite-ferrite boundaries should be negligible in relation to that at which they form in other regions of the austenite. During this investigation, however, many groupings of ferrite crystals have been found which appear to have resulted from the nucleation of ferrite at austenite-ferrite boundaries. This phenomenon has been given the name of sympathetic 71.1tcleation. A number of micrographs of morphological configurations caused by sympathetic nucleation will be presented, after which an explanation for this reaction will be proposed in terms of current nucleation theory. Some of the structures to be considered are composed of bainite, an aggregate of ferrite and carbide, rather than of ferrite. Since ferrite and bainite differ only in that bainite forms under conditions which result in the nucleation of carbides behind the advancing austenite-ferrite boundaries,' it will usually be unnecessary, for the purpose of this paper, to distinguish between the two reaction products. All studies were performed on an electric furnace steel (obtained from the Vanadium Alloy Steel Co.) containing 0.29 pct C, 0.76 pct Mn, 0.25 pct Si, 0.005 pct P, and 0.007 pct S. The alloy was cast as a 150 Ib, 7x7 in. cross section ingot and forged into bars 2x2 in. in cross section. These bars were homogenized for 48 hr at 1250°C in an Endo-Gas atmosphere. The depth to which decarburization penetrated during this heat treatment was determined by chemical and microscopic analyses and the affected metal was removed by machining. Specimens for isothermal transformation studies were cut from the remaining material; most of these specimens were 1/2x1/4X1/16 in., though some with a thickness of 1/32 in. were prepared for use at the shorter reaction times and lower reaction temperatures. Specimens were austenitized for 30 min at 1300°C, isothermally reacted for various times at temperatures ranging from 775" to 475 "C, and then quenched in iced water. The austenite grain sizes within individual specimens ranged from ASTM Nos. 1 through —4. A commercial heat-treating salt which was continuously deoxidized by an immersed graphite crucible served to minimize the loss of carbon during austenitizing; thick covers of powdered graphite and immersed graphite rods effectively prevented decarburization in the lead pots employed for the isothermal reaction treatments. The heat-treated specimens were sectioned and mounted in Bakelite. Following the completion of standard grinding and mechanical polishing procedures, the specimens were electrolytically polished with a Buehler-Waisman apparatus and etched in 2 pct nital. Experimental Results Rules of Evidence for Sympathetic Nucleation—On the basis of observations made on a single plane of polish, one precipitate crystal may be considered to have been sympathetically nucleated at the inter-phase boundary of another precipitate crystal when the following conditions are fulfilled: 1) The sympathetically nucleated crystal is not in contact with a grain boundary or a subboundary in the matrix phase. 2) The shape, size, and location of the crystal at whose boundary sympathetic nucleation occurred (hereafter termed the base crystal) and the crystal formed by sympathetic nucleation substantially pre-clude the possibility that the plane of polish em-ployed may have concealed the fact that both crys-tals actually nucleated at a grain boundary or a sub-boundary in the matrix phase.

Jan 1, 1957

By Robert F. Calman

OUTLINE FIVE EXAMPLES OF GOLD-LINKED FINANCINGS 1. Financing the Lupin Mine • Sale of Cdn $40.0 million of 12% preferred shares and Cdn $40.0 million of Gold Purchase Warrants @ $595 per ounce. 2. Financing the Copper Range acquisition • Borrowing 100,000 ounces from a Canadian chartered bank @ US$307 for five years. 3. Financing the Round Mountain expansion • Borrowing up to US $80.0 million in dollars, convertible into gold, repayable over five years from a group of North American banks. 4. Financing the Tenneco Precious Metals Division acquisition •Sale of SFr 110.0 million of ten year 3-718% bonds with warrants to buy 132,000 ounces of gold at US $560. 5. On Forward Sales, Puts and Calls • Gold, Silver, Canadian Dollars, Swiss Francs THE FINANCIAL RULES AT ECHO BAY 1. Never bet the company 2. Equity is the primary form of capital for a gold mining company 3. On debt 4. The Yardsticks for Corporate Decisions 5. Financial Community Relationships 6. Dividend Policy No Text Available Tables Follow

Jan 1, 1990

By Leonard H. Goldman, Harold E. Marr

The PGT uranium assay probe is a borehole tool developed by Princeton Gamma-Tech over the last several years. It has the ability to do an in-situ assay of uranium in the presence of any amount of disequilibrium. It has some advantages over coring including cost, speed of analysis, and accuracy. In this paper we would like to give a brief description of the measurement and then show some sample logs from South Texas. Uranium exploration and development is carried out primarily by gamma logging since uranium daughters are prolific emitters of gamma rays. The conventional gross gamma tool for uranium logging is limited in value because of the inability of this tool to distinguish uranium from its daughters and other naturally occurring radioisotopes, such as potassium and thorium. This problem becomes severe in cases of disequilibrium. Disequilibrium, in a geological context, is defined as the condition when the gamma radiations from the daughter products are being emitted in a location different from that of the parent uranium. In the decay chain of uranium almost all the gamma radiation emitted in the entire chain comes from the daughter product, bismuth-214. Bismuth-214 is separated from uranium by several long-lived isotopes that are chemically active and have different physical properties, often resulting in shifts in the location of bismuth- 214 relative to the parent uranium. In the United States orebodies exhibiting disequilibrium are a common occurrence and the use of a gross gamma log to delineate uranium orebodies can lead to errors. At present the solution to the disequilibrium problem is extensive coring followed by chemical analyses of the cores. There are several drawbacks in using this technique. First is the high cost of coring, the second is the fact that no results are available for days, or typically, weeks after the drilling is done. Thus for development work, coring and drilling must be done on a grid basis and many additional holes are cored to ensure that the entire orebody is mapped. Another disadvantage to cores is the fact that a small volume is sampled, the volume of the core itself. This leads to problems in the mapping out of the orebody when the ore de- posit is not very homogeneous. The PGT probe described in this paper is a new solution to the disequilibrium problem. Basically, the probe measures radiations that come almost directly from uranium itself. The first daughter of uranium, which is protactinium-234 (Pa-234), is only separated from uranium by a 24-day half-life and no disequilibrium problems build up in such a short time. The PGT probe measures the intensity of a one MeV gamma line emitted by Pa-234 and, using this information, calculates the concentration of uranium. The PGT probe is 24" in diameter and 12 feet long. The probe contains a microprocessor which passes the information to a larger minicomputer in the truck. All data is analyzed on site, and the results from a high speed printer are presented to the geologist. Data is also available on 9- track IBM compatible tape for further processing. The PGT probe output is linear with uranium concentration. The only correction factor is for borehole size, and that only becomes important in boreholes bigger than seven inches in diameter. Dead time is compensated in the probe itself and no problems have been encountered in ore zones up to several percent UjO8. In addition to the uranium assay, a conventional gross gamma log is plotted alongside. Grade thicknesses for zones above cutoff are calculated as well as disequilibrium factors. COMPARISONS During its commercial operation PGT logged a series of 18 holes that had been cored and assayed. All of the holes in this series were logged in normal operation by regular field operators. The time to log each hole was generally under an hour, and in typical operation a PGT logging truck will do between 7 and 8 holes a day. The results of the comparison of the PGT and the core assays are presented in a series of figures showing plots of the PGT assay, core analysis and gross gamma measurements. The first three figures show individual holes with the gross gamma plotted along with the core and the PGT assays. All three logs were from holes on the reduced side of a rollfront deposit in South Texas. In Figure 1 we see the two wings of the roll- front at 143 ft and 150 ft separated by a barren zone. The wings are well defined both by the PGT assay and the core. There is approximately a one foot shift which can be attributed to drilling errors. The gross gamma is showing a rather severe discrepancy, being considerably lower and not showing the barren zone. The grade thickness calcula-

Jan 1, 1980

By Samuel H. Dolbear

THE value of a mine is basically dependent on its capacity to yield profits. Since the ore must be mined, treated, and sold, some of it in various future years. there is a risk involved as to future costs, selling price, and working conditions. It cannot be expected that the economic condition existing at the time of valuation will continue unchanged for long periods in the future. During the past 20 years, mineral production in the United States has been conducted under a changing economy in many respects more exacting than that applied to other businesses. There have been increased production incentives, technical aid, exploration of privately owned mineral deposits by government at federal expense, and liberal loans for development and equipment, with risk partially assumed by government.. Some of these benefits have been counterbalanced by price ceilings, consumption controls, and stimulation of competition from foreign producers who have been offered the same advantages extended to American operators. For the present, mines will operate under a government policy directed toward reducing federal aid and control. The tenure of this change will depend upon future elections and the status of foreign relations. War and threat of war are now of the most vital significance to the mineral industries. Other factors which influence cost of production, markets, and price of mine output might be classified as Acts of God or Acts of Government. In some countries expropriation and the difficulty of exporting earnings or investment returns are risks that must be considered by foreign capital. Recognizing that this retards American investment in foreign countries, the Mutual Security Agency offers insurance against such expropriation and guarantees the convertibility of capital and profits. Since it is impossible to predict with certainty either cost of production or selling prices of metals for long periods, some assumptions must be made as to profits in the future. The basic assumption must be that the price of the company's product will vary in proportion to changes in operating cost. There is often a lag in this reaction, however, for prices of minerals are generally more sensitive to declines and less sensitive to increases than are costs. This reflects in part the resistance of labor to downward wage revision and a corresponding alertness in realizing its share of price advances. Some labor contracts include automatic adjustments to metal prices. Notwithstanding the complexity of the, problems involved and the difficulty of weighing their effect on value, such risks may be appraised with reasonable accuracy and a rate of earnings adopted that is compatible with the risk. It is, of course, possible to revert to a yardstick of value such as the commodity dollar, which has been advocated from time to time, but while revaluation in 1933 disturbed public confidence, the theoretical gold dollar continues to be the standard of greatest stability. Its gain or loss in purchasing power is reflected ultimately in cost of production and selling price of the mine product. At present 35 dollars are allocated to one ounce of gold. Measurement of Risk In the application of the Hoskold and most other formulae, a yearly dividend rate commensurate with the risk involved is set aside out of annual earnings. If the risk is great, this rate may be 15 to 25 pct of the amount invested. The remainder is placed in a sinking fund invested in safe securities such as high grade bonds or conservative equities, and the interest or dividends from these securities are added to the sinking fund. The sum of these sinking fund payments and the compounded interest at the end of the mine life is taken as the value of the mine. Admittedly the decision as to the size of the risk rate is the most difficult element in valuation and one requiring the most exacting consideration. It is necessary to look years ahead in an effort to determine future costs, market prices, demand, competition which may develop, including that of substitutes, and other influences common to the mine and to the region in which it is situated. Another phase of risk is the enactment of unfavorable legislation, taxes, and what appears to be an alarming spread of nationalization and expropriation. Capital is sometimes borrowed from the government to finance strategic production. Such loans may be collectable only out of production and involve no liability otherwise. Valuation in these cases must recognize the effect of such a reduction in liability. Offsetting some of these risks are the possibilities of mechanization and other cost-reducing discoveries, improvements in mining and treatment methods, new uses for minerals and metals, and normal growth of markets. In this paper, the terms risk rate, dividend rate, and speculative rate are synonymous. Safe rate and redemption rate are also used interchangeably. These alternatives are used here because they are commonly found in the literature on mine valuation. In Michigan, the State Tax Commission has long employed a risk rate of 6 pct in its valuation of iron mines. There the outline of reserves is well established and operating costs and conditions are based on adequate experience. The following comment on rates appears in the report of the Minnesota Interior commission on Iron Ore Taxation submitted to the Minnesota Legislature of 1941.1 Most engineers agree that 7 percent for the specu-lative rate is "an absolute minimum". C. K. Leith in

Jan 1, 1954

By P. L. De Bruyn

The adsorption density of dodecylammonium ions at the quartz-solution interface has been Theadsorptiondensitydetermined as a function of collector concentration and pH. A ten thoushasbeenandfold range of amine salt concentration was covered at neutral pH. Experimental results show that over a thousandfold concentration range at neutral pH, the adsorption density (I) is proportional to the square root of collector concentration. Except at high concentrations, I increases with increases with increasing pH, but in general this effect is surprisingly small. . , . . A critical pH curve has been established for the flotation of quartz with dodecylammonium acetate. The conditions along the flotation curve are correlated with the adsorption measurements. THE behavior of collectors at the mineral-solution interfaces is usually explained in terms of an ionic adsorption process. Through the distribution of collector ions between the solid surface and the- co-existing solution phase the mineral is believed to acquire a water-repellent surface coating. Quantitative adsorption studies have been made on simple flotation systems1-4 only within the last few years. Such investigations were made possible by the adoption of the radiotracer method of analysis. As a consequence of these studies a new parameter has been added to aid the understanding of the flotation process. The research investigation to be discussed in this paper was undertaken to obtain a better understanding of the behavior of a cationic-type collector. This objective was approached through the determination of the distribution of dodecylammonium acetate between the quartz-solution interface and the solution as a function of the collector salt concentration and pH. To bring this investigation to focus on the more practical aspect of flotation research, an attempt was also made to correlate the adsorption results with actual flotation tests. Quartz: A —100 mesh ground crystalline quartz was infrasized; the products of the third and fourth cones were mixed together and reserved for experimental purposes. This stock material was cleaned by leaching in boiling concentrated HC1. After leaching the quartz was rinsed with distilled water until the filtrate showed no trace of chloride ian. It was then washed several times and dried. The qwrtz had a specific surface of 1400 cma per g as deterhined by the krypton gas adsorption method. Collector: The distribution of dodecylammonium acetate between the quartz surface and the solution phase was determined by the radiotracer method of analysis with carbon 14 as the tracer element. The radioactive amine salt with C" synthesized into the hydrocarbon chain5 was supplied by Armour and Co. The tracer element was located adjacent to the polar group. The radioactive salt as received had a specific activity of about 0.14 mc per g. When desired, dilution of this activity was effected by addition of non-radioactive dodecylammonium acetate also supplied by Armour and Co. ........ All other inorganic reagents used in this research were of reagent grade. Conductivity water was used for making up all solutions. Adsorption Tests: Two different experimental methods were used. In the first, to be designated as the agitation method, a weighed amount of quartz and a measured volume of amine salt solution were agitated in a 100-ml or 50-ml glass-stoppered pyrex graduated cylinder. The cylinder was filled with solution up to the stopper, since erratic results were obtained when an air space was left over the suspension. Time of agitation varied from 1 to 2 hr. Preliminary tests at different agitation times showed that the amount adsorbed remained constant for all agitation times exceeding 1/2 hr. After this conditioning period, the solids were separated from the solution by filtration through a Buechner fritted-disk funnel. The solution was re-circulated 10 times or more to allow the fused silica disk to come to equilibrium with it. Determinations of the amount of amine adsorbed on the frit itself indicated that this amount was less than 10 pct by weight of the amine acetate abstracted by 10 g of quartz. The funnel with quartz covered by a thin layer of solution was then centrifuged for approximately 5 min, at which time the moisture content of the solids was reduced to about 5 pct by weight. The wet quartz was blown into a tared beaker, re-weighed and allowed to dry at room temperature. A final weighing was then made to determine the moisture content. The second experimental method, similar to the procedure adopted by Gaudinand Bloecher,' will be referred to as the column method. Two liters of solution were passed through a bed of quartz contained in a Buechner funnel attached to a pyrex separatory funnel by means of a ball and socket joint. Preliminary tests showed that increasing the volume of solution above 2 liters does not give a measurable increase in adsorption. From 4 to 4 1/2 hr were required for 2 liters of solution to pass through the column. The moisture content of the quartz was again reduced to a minimum by centrifuging. A slightly modified column apparatus was used for experimenting with alkaline amine solutions. The same basic unit was used, but the underflow from the Buechner funnel was again fed into a Separafory

Jan 1, 1956

By W. C. Smith, P. J. Hickey

After a short historical background of the process evolution, this article descvibes present-day plant facilities and operating techniques utilized for high-purity bismuth production. The plant is one of the world's largest, with an annual output of some one million pounds of refined bismutlz. PREVIOUS papers1 written by staff members of Cerro de Pasco Corp. have referred briefly to the production of refined bismuth. Since the Corporation is one of the world's foremost producers of high-purity bismuth, a detailed description of the process for extracting the metal may be of general interest. Following a short historical background of the development of the actual process, this presentation will trace the progress of bismuth from its entry into the primary smelting circuits to its concentration in electrolytic lead cell slimes. Our facilities for the treatment of anode muds will be described and the extractive methods given in some detail, with particular emphasis on the techniques which result in the production of refined metal. HISTORICAL BACKGROUND Shortly after Cerro de Pasco began smelting operations at Oroya, Peru in 1922, it became apparent that the dust carried by copper converter gas contained appreciable amounts of bismuth. Although dust collection efficiency was poor prior to building of the 550-ft stack and installation of the central cottrells in 1938, a large stock of dust was accumulated during the intervening years, having the following approximate composition: Oz. per ton Ag - 11.0 Pct Sn — 0.5 Pct Pb - 49.0 Pct Zn - 6.5 Pct Bi - 2.0 Pct Insol. - 1.5 Pct Cu - 0.7 Pct Fe - 2.3 Pct Sb - 3.0 Pct S - 10.0 Pct As - 7.5 In the mid-1920's, experimental crucible melts of this dust with carbon indicated that most of the bismuth and silver, and some of the lead, could be reduced to a fairly clean bullion. Other products were a small amount of leady copper matte and a slag high in zinc, arsenic, antimony, and lead; this slag contained some tin but only small quantities of silver, bismuth, and copper. After the laboratory results had been confirmed by operation of a small reverberatory, a dust reduction furnace was constructed. The ±10 pct Bi-Pb bullion produced from this operation was stocked until 1930, when an Oroya-designed converter type furnace3 was installed for the elimination of arsenic, antimony, and some lead from the bullion. This process concentrated the bismuth from 10 to about 60 pct. By means of the bismuth process developed4 by W. C. Smith at East Chicago (1909-1914) and the discovery of a method5 for separation of lead from bismuth with chlorine gas in 1929, it became possible to begin production of refined bismuth. Unfortunately, bismuth deleaded with chlorine always contained residual chlorides, and the removal of the chlorides by caustic soda left a lead content of 0.02 to 0.04 pct. This final problem was solved6 by substitution of air-blowing for the caustic treatment, which effectively removed all excess chlorine and gave bismuth which was practically lead-free. In 1934, a pilot electrolytic lead refinery began operations at Oroya. Lead smelting was resumed in 1935 and two years later a 100-ton-per-day lead refinery was put into service. In conjunction with the latter, the present-day Anode Residue Plant was constructed. Until 1940, the plant treated both lead anode slimes and dust reduction bullion. The dust reduction furnace was shut down in that year, and all cottrell dusts (with the exception of the product from the arsenic cottrell) were mixed with pyrite and treated in a Wedge roaster to eliminate all possible arsenic. Calcine from this operation joined the sinter plant feed; hence the bismuth from the copper and lead circuits was collected in the lead bullion and subsequently in lead anode slimes from the electrolytic lead refinery. The latter source has been the only bismuth-bearing material of any consequence entering the Anode Residue Plant from late 1940 to the present. A copper refinery began operating in 1948, and the cell mud from this plant is mixed with lead slimes and processed through the same circuit, though only a small quantity of bismuth is present in electrolytic copper cell residues. BISMUTH INTAKE Present-day routes which are followed by the new bismuth feed from its entry into the primary smelting circuits to its arrival at the Anode Residue Plant are traced schematically in Fig. 1. As illus-

Jan 1, 1962

By J. E. Lawver, J. D. Raulerson, Charles C. Cook

The agriculture industry has made great strides during the past decade to increase agriculture yields through increased use of fertilizers. Increased use of fertilizers may prevent, or at least delay, mass starvation due to the alarming increase in world population. Phosphate was added to soil as a plant nutrient in the form of calcined bones at least 2000 years ago (Anon., 1964), and man has used phosphate minerals as a source of fertilization in one form or another for at least 100 years. During 1977 the world produced about 116 Mt of phosphate rock, with about 86% used for fertilizers and another 4% for animal feed supplements. More than three-fourths of the total production comes from the United States, Morocco, and the Soviet Union. From a mineral beneficiation point of view, the major sources of phosphate rock and the methods of beneficiation can be classified as follows: marine deposits not containing appreciable carbonate minerals, marine deposits requiring a francolite carbonate mineral separation, igneous deposits not containing appreciable carbonate minerals, and igneous deposits requiring apatite carbonate mineral separation. [ ] Guano, mostly from Chile and Peru, accounts for 0.1% of the total world production, and the calcium phosphates from Ocean, Nauru, and Christmas Islands and the aluminum and iron phosphates from Brazil and Aruba account for less than 4% of the world production and are thus not considered in this classification (Lawver, et al.). At present, marine phosphorite deposits account for about 75% of the world's production; the igneous deposits account for 20%. The igneous deposits low in carbonate minerals are easily concentrated by crushing, grinding, and apatite flotation. The most important igneous deposits are those of the Kola Peninsula, USSR (Woodrooffe, 1972). The igneous deposits high in carbonate materials are of corn appreciably more difficult to beneficiate, but they have been concentrated by froth flotation for a number of years. An interesting but rather complicated flowsheet of this type is at Phalabonva, in the Republic of South Africa (Lovell, 1976). The Phalaborwa deposit is an igneous complex of pyroxenite with a central core of carbonatite surrounded by a serpentine- magnetite-apatite rock called phoscorite. The phoscorite containing about 10% P2O5, 35% magnetite, and 35% calcium magnesium carbonate is currently being processed. The process involves comminuting the material for fiberation and subjecting it to a copper float using a potassium amyl xanthate as collector and triethoxybutane as a frother followed by a magnetic separation of the tailings to produce a feed for phosphate flotation. This process produces a phosphate concentrate containing greater than 36% P2O5 at a P2O5 recovery ranging from 75 to 80%. Considerable success has been claimed for recovering apatite from carbonate-bearing ores at the Jacupiranga Mine of Serrana S/A (Silva and Andery, 1972). The carbonatite currently being mined contains an average of only 5% P205 and is concentrated using a unique flotation process (Andery, 1968) to yield 96% P205 concentrates. The ore contains about 12% apatite, 5% magnetite, 80% calcite plus dolomite, and minor amounts of phlogopite, olivine, zircon, ilmenite, and pyrochlore. Feed preparation consists of crushing to -31.75 mm (-1 M in.), rod milling in closed circuit with hydrocyclones to about 92% (-50 mesh), and two-stage cyclone desliming of the -50 mesh sands at 20 m. Weight recovery in the deslimed feed is normally 85 to 88% and the corresponding P2O5 recovery is usually about 90%. The deslimed feed is conditioned at 60 to 70% solids for 15 min at pH = 8-10 with 0.6 kg/t of causticized starch for iron oxide and calcite-dolomite depression. The conditioned slurry is diluted to 20 to 30% solids, about 0.2 kg/t of fatty acid or soap collector is added to the conditioner discharge, and the reagentized ore is subjected to rougher-scavenger flotation with additional fatty acid added to the scavenger float. The scavenger concentrate is returned to rougher circuit distributor, and the rougher concentrate froth is subjected to two stages of cleaner flotation to yield a final apatite concentrate analyzing 36 to 38% P205. Flotation recovery of P205 is, in general, above 90% when treating fresh carbonatite. The high-carbonate flotation tails normally analyze 1 % P2O5 or less and are suitable for portland cement production. The marine deposits. Types 1 and 2 of central Florida are representative of enormous reserves of phosphate rock that will undoubtedly account for much of the world's production in the near future. Until very recently the sedimentary deposits high in carbonate minerals (Type 2) have not been considered reserves due to the difficulty in making a francolite-carbonate separation. Although no commercial plant has yet been built to beneficiate Type 2 ore, laboratory and pilot plant data indicate the process is viable. If so, the reserves of Florida and similar deposits throughout the world will be substantially increased. A discussion of the beneficiation of these two types of sedimentary deposits and the relation of the resulting concentrates to the fertilizer industry of the United States is the subject of this paper.

Jan 1, 1981

By B. H. Kear, S. M. Copley

Stress-stvain curves are presented for Ni3Al (y') cvystals in several ovientations, deformed in tension and compression at constant displacement rate, at temperatures from 70° to 2000°F. Both the yield stress and wovk havdening increase with temperature, with the magnilude of the effect dependent on ovientation. The yield stress maximum occurs at 1500°F in [001], at 1400°F in [011], and at 1200°F in [111]. The suppression of the yield stress peak in [011] and [111] orientatiorzs is due to the onset of cube slip, rather than octahedval slip, a1 elerated temperatures. The temperature and orientalion dependence of work hardening in nominal single slip orientations corvelates with changes in the CRSS ratio for octahedral slip and cube slip, in agreement with a model for work hardening based on pinning of screw dislocalions by cross slip from an octahedral plane into a cube plane. It is concluded that the unique plastic properties of y' have a decisive influence on both ductility and strength characleristics of y +y' nickel-base superalloys. It has long been recognized that the strength of y + y' nickel-base superalloys depends on the precipitation of the y' phase [basically Ni3(Al,Ti)]. This paper presents new data on the strength characteristics of single crystals of simple y' (Ni3Al), and forms the first step in a systematic program aimed at elucidating the mechanisms of hardening in the complex commercial alloys. 1) EXPERIMENTAL PROCEDURE Single crystals of off-stoichiometric NiA1 were grown from the melt under vacuum by a modified Bridgman method. The melt was poured into a preheated alumina mold and crystal growth was promoted from one end by gradient cooling. The crystals were homogenized by annealing in hydrogen at 2400° F for 72 hr followed by furnace cooling. Chemical analysis of samples taken from several crystals gave an average composition of 88.2 wt pct Ni. Spectrographic analysis gave as the principal impurities in weight percent— Si (0.02), Mg (0.01), Fe (0.02), Ti (0.002), Cu (0.008), and Co (0.03). Tensile specimens with specifications as in Fig. 1 were prepared by a series of operations involving electrical discharge machining, precision grinding, and electropolishing. Compression specimens with dimensions 1/4 by 1/4 by -3/4 in. were prepared in a similar manner, except for the initial shaping operation using a precision cut-off wheel/two-circle goniometer unit to give selected crystal orientations. Specimens were deformed in a Baldwin-Wiedemann testing machine with furnace attachment, using a strain rate of 5 x 10-4 sec-1. The strain measuring device consisted of extension arms attached to the tensile grips (or compression plattens) at one end and leading out of the furnace to an LVDT at the other. Temperature was controlled by a thermocouple placed in contact with the specimen. According to the known phase diagram for the Ni/A1 system,' when an alloy of the specified composition is cooled from the melt, primary y (nickel solid solution) dendrites grow at the expense of the liquid phase, which becomes enriched in aluminum. At the eutectic composition the remaining liquid freezes as a two-phase mixture of y + y' (Ni3Al). Upon further cooling, a solid state transformation occurs, involving the precipitation of y' in the primary dendrites, and the complete transformation of the eutectic mixture to massive y'. The as-cast structure consists, therefore, of y + y' dendrites with interdendritic regions of massive y', i.e., transformed eutectic, Fig. 2. 2) DISCUSSION OF RESULTS 2.1) Stress-Strain Curves. Fig. 3 shows tensile stress-strain curves for crystals in orientations close to [001] deformed at temperatures from 70° to 2000°F. Both the yield stress and total elongation are strongly temperature-dependent. At 70°F, easy glide is absent, and the work hardening coefficient BIT - G/300. At T > 1500°F, the negative slope of the stress-strain curves is due to pronounced necking in the crystals. The yield stress maximum at 1500° F corresponds with a minimum in the ductility, Fig. 4. The extensive duc-

Jan 1, 1968

By H. A. Jr. Koch, C. A. Hutchinson

Miscible phase displacement of oil from reservoirs has been emphasized in the past few years. The reason for this emphasis lies in the high oil recovery attainable by this process. Removal of capillary effects in the reservoir leads to recoveries approaching 100 per cent in the area contacted by the miscible phase. The miscible slug process is one means of obtaining a miscible displacement. Here a band or slug of I,PG is injected into the reservoir prior to gas injection. The idea is to maintain the band of LPG "wedged" between the gas and oil phases and thus achieve a miscible phase displacement. A second method lor achieving miscibility is through the injection of a gas which is not miscible with the reservoir fluid but which develops a zone of miscibility in [he reservoir through mass trans-ier with the reservoir oil.' This mass transfer results in either an enrichment of the lean injected gas by intermediates from the oil or an enrichment of the oil by intermediates from a rich injection gas or one that has been enriched on the surface by LPG addition. We are interested here in discussing the process in which miscibility is developed at the displacement front by the evaporation of interrnediatcs from the oil phase into the gas phase. This process "builds up" its own slug of miscible material at the displacement front and therefore does not require the injection of LPG to obtain miscibil-ily. Each process has its own area of applicability. Generally, the high pressure gas process is applicable only with reservoir fluids which con-!ain a high concentration of inter- mediates. If the high pressure gas process is technically feasible at pressures less than 4,500 psi, it is probably more desirable economically than the slug process. The slug process has broad applicability in the shallower reservoirs and with reservoir fluids which contain a relatively low concentration of LPG and natural gasoline constituents. This paper deals with some new concepts of the high pressure gas injection process where it is proposed that flue gas can be substituted for hydrocarbon gas without sacrificing our goal of miscibility. MECHANISM Introduction Considerable effort has been devoted to study of the mechanics ot the high pressure gas injection proc-one generalization result-ing from some of these studies was that the composition of the injected gas is relatively unimportant in establishing the miscibility pressure* for a given reservoir fluid. This generalization is correct for the composition range of gases typically encountered in the field. Two such gases are a gasoline plant tail gas containing 85 per cent methane and 15 per cent ethane, and a field separator gas containing 70 per cent methane and 30 per cent heavier components. The most important factor which sets the miscibility pressure in the operation is the reservoir fluid composition, particularly the concentration of LPG-natural gasoline constituents. The injected gas is the agent by which the LPG-natural gasoline constituents are concentrated at the displacing front to create a miscible displacement. Based on these results, it appeared feasible that some inexpensive gas, such as flue gas, might be substituted for hydrocarbon gas for use in the high pressure gas process. A re-examination of the phase relations of the high pressure gas injection process should clarify the principle behind using flue gas (essentially nitrogen) as an injection gas. Three Component Diagram The phase relations of the high pressure gas injection process have been illustrated by the use of the three component diagrams.'," In Fig. 1 we have arbitrarily represented the multi-component reservoir system by three components; methane, ethane through hexane, and heptanes plus. The solid curve ABC is the phase boundary curve. It represents the locus of compositions which have fixed saturation pressure at a fixed temperature; the lower branch AB shows bubble point compositions, the upper branch BC, the dew point compositions. Point B is the coniposition of the critical mixture at this temperature and pressure. The dashed lines (tie lines) connect vapor and liquid compositions which are in equilibrium. Let us consider Reservoir Fluid D which we wish to displace in 21 miscible manner by gas injection. Let us further restrict the discussion to the case where miscibility between an injection gas and the reservoir fluid at the displacement front is developed by gas enrichment in the reservoir. For this case, any gas whose composition lies between Points C and E on the right side of the three component diagram can be used to give a miscible displacement of Reservoir Fluid D. This is true because the more mobile injected gas moves faster than the displaced oil and is in continuous contact with virgin oil at the displacement front. This leads to a continuing enrichment 01' the gas at the displacement front by evaporation of the C, - C,

By D. M. Metcalf

MOST PEOPLE think of peat as an inferior substitute for coal as a fuel, and will be surprised to learn that it is extensively mined in this country for use as fertilizer rather than as a fuel. Some years ago the Florida Humus Co. began producing it at Zellwood, Orange County, Fla., in a small way for local use. When, however, the company secured an Institute member, M. H. Cuise, to apply his wide experience in mining to the problems here it was found possible to decrease production costs 70 per cent and increase output tenfold. The obvious way in which to decrease costs was to replace shovel-and- horse methods with machinery, much of which, in order to keep down-invested capital, was improvised by remodeling second-hand equipment, changing the design where necessary to meet the special conditions involved.

Jan 1, 1932

By Paul Averitt

require both time and money. Any attempt to secure a quick answer will yield a figure that very likely cannot be substantiated, and certainly will not yield information in the detailed form now desired. It will be about 10 years before a completely new estimate can be prepared for the coal reserves of the United States at our present rate of progress, though of course, much information will be available in the interim. We would like to present such information as we obtain in the form most acceptable to the industry, and to that end we are working closely with coal resource committees of the AIME, the National Bituminous Coal Advisory Council, and the Bureau of Mines. DISCUSSION G. H. Cady*—Mr. Averitt's description of the nature of the coal resources investigations of the United States Geological Survey and the progress of this work is very timely in view of the general interest in the subject of coal resources. The Federal Survey is obviously taking the "long view" with respect to the appraisal of the coal resources as part of the preparation of the general geological map of the country and the attendant determination of the quantity of all mineral and fuel resources. It is apparently for regional surveys of the conventional type that the detailed procedures employed by the Federal Survey are applicable. Even if so it is somewhat unexpected to find the same criteria for evaluation will be applied to the country as a whole. The work on coal resources appraisal has been proceeding at various rates in a number of coal producing states for various periods. Undoubtedly since there has been no common practice in the method of appraisal the states each have worked independently and independently of the Federal Survey, and each has adopted certain practices to meet local conditions. I do not know how much consideration has been given by the U. S. Geological Survey to these practices. It seems probable that such consideration might result in important modifications of the standards which apparently have been set up by the Federal group in line with local requirements. It is the practice in some state surveys to present the facts in regard to the occurrence and distribution of coal beds and their variations in thickness down to thicknesses of 1 to 1 1/2 ft in relatively narrow stages up to maximum thickness. It is then possible for any one using such figures to compile quantitative estimates of workable coal at various minimum thickness limits. This is a desirable objective where surveys are detailed and information correspondingIy good. However, vast quantities of coal lie in beds that are relatively thin about which little information is available and the quantity of such coal might affect the final appraisal to the extent of several thousand million, depending upon the minimum limitation observed. Thus in the case of Illinois a difference of 1 ft in average thickness of coal in the coal field would make a difference of approximately 35 billion tons in the estimated quantity present. One is dealing with a very large area and small differences in thicknesses are very irnportant in the overall picture. The estimate of 10 years to accomplish the sort of detailed appraisal outlined by Mr. Averitt is viewed somewhat skeptically and certainly would require many more trained geologists than seem to be available. The requisite detailed mapping and study are very time consuming not only because of the geological field work required, which is difficult in certain seasons, but also in order to assemble data from company and personal files, and to study drill records and cores, and to sample and analyze the coal. Unless the staff of geologists could be increased in the order of several hundred per cent the prospects are that the appraisal of the type suggested will require many decades not just one. The permanent value of such appraisal, however, is not questioned and it should be expedited as rapidly as means allow. Satisfactory appraisal is not easily achieved and will vary from time to time. The main function of a geological survey is to collect and present the facts that will make possible appraisal in terms of existing conditions by individuals, particularly engineers, qualified by training and expcrience for making such estimates. Thickness and character of the coal bed, nature of the overlying and underlying strata, position, thickness, and character of "partings," relationship to other coal beds, and a variety of other factors must be assembled by the geologist in order to present a complete picture of the geological setting. The economic and engineering factors are in general outside the field of geological experience. The geologist should see to it that the pertinent geological facts are available; much more information than simply thickness and depth of the coal beds is essential to meet all the requirements of appraisal in the future as well as at present. With respect to the present demand by engineers and coal mine operators and others for a rapid re-appraisal of the available coal resources, in the light of existing practices and those in immediate prospect, the Federal procedure of systematic mapping and appraisal is scarcely in line. It will be necessary for those particularly interested in having such an estimate made to establish standards with respect to the various factors involved so that the scope of the geological work can be definitely restricted for the various coal fields. There is little use in setting up general standards since no such standards will be applicable to all fields. Thus it is folly to establish a standard minimum thickness to be generally applicable which is one-half to one-third the minimum minable thickness in some fields. The greatest difficulty in appraisal of the presently actually workable coal bed lies in the variation in the importance placed on roof, floor, structural conditions, bedded impurities. sulphur content and other factors that affect judgment relative to the value of a coal bed. It is doubtful whether any appraisal will have universal approval in view of the variable factors involved. For this reason if none other, the facts should be carefully and painstakingly assembled after the manner of a systematic geological survey such as that advocated by Mr. Averitt. Only upon the basis of sucb information can reliable estimates be made in line with selected conditions. Paul AveRitt (author's repty)— In this paper I discussed, but did not define as such, two major phases of our activities on coal, which are closely related, and which normally we in the U. S. Geological Survey see as an integrated whole. It is understandable, therefore, that Dr. Cady should assume that my remarks applied only to the current work on coal reserves with which I am directly concerned. In view of Dr. Cady's discussion, however, I think a brief summary of the two phases of U. S. Geological Survey activities on coal will be appropriate. The long-term function of the U. S. Geological Survey on coal investigations is to make detailed geologic studies, involving the preparation of detailed geologic maps showing the outcrops and correlations of coal beds, direction and dip of coal-bearing rocks, nature and thickness of overburden, location of faults and fold axes, and similar features. Such studies also yield many measured sections of coal and associated strata, which show variations in the thickness of the beds, and the intervals between coal beds. Taken as a whole, detailed geologic studies provide much useful information for mine operators and engineers. As Dr. Cady points out, this type of geologic work is arduous and time consuming, but it provides the basic data that are necessary both in the development of our coal fields, and also in the preparation of coal-reserve estimates, which are discussed in the next paragraph. The U. S.

Jan 1, 1950

By Joseph E. Pogue

In 1920, 531 million barrels of crude petroleum were coi~sumed in the United States. As imposing as this figure is, the fact that the domestic consumption of crude petroleum has increased at an average rate of 10 per cent. a year for the past decade is more striking. Will this rate of increase in demand continue? If so, the year 1930 will call for 1260 million barrels of petroleum—a staggering volume. On the other hand, may we expect the demand for petroleum to grow as rapidly as it did when the automotive industry was having its most phenomenal expansion? If not, to what extent will the growth of oil requirements decrease? When and to what degree will the petroleum industry become affected by the economic law of diminishing returns? Obviously, this matter requires careful analysis, especially as both national and industrial planning must be predicated upon present estimates of the requirements of the future. The purpose of this paper, accordingly, is to project, as closely as present limitations of knowledge permit, the course of the demand for petroleum in the United States over the next ten years. At first, the problem of estimating the future of a demand as complex as that for petroleum might appear insoluble. Fortunately, hon~ever, therc are several scientific methods of approaching the problem, centering around a study of rates of industrial growth, which lend considerable hope that the requirements of the immediate future in this field may be approximated with sufficient closeness to have practical value as a basis of action. Growth oF Petroleum Demand The demand for crude petroleum is the resultant of the demands for the products made jointly from this substance—gasoline, kerosene, gas and fuel oil, and lubricating oils. The demands for these have grown at

Jan 1, 1923

By Joseph E. Pogue

In 1920, 531 million barrels of crude petroleum were coi~sumed in the United States. As imposing as this figure is, the fact that the domestic consumption of crude petroleum has increased at an average rate of 10 per cent. a year for the past decade is more striking. Will this rate of increase in demand continue? If so, the year 1930 will call for 1260 million barrels of petroleum—a staggering volume. On the other hand, may we expect the demand for petroleum to grow as rapidly as it did when the automotive industry was having its most phenomenal expansion? If not, to what extent will the growth of oil requirements decrease? When and to what degree will the petroleum industry become affected by the economic law of diminishing returns? Obviously, this matter requires careful analysis, especially as both national and industrial planning must be predicated upon present estimates of the requirements of the future. The purpose of this paper, accordingly, is to project, as closely as present limitations of knowledge permit, the course of the demand for petroleum in the United States over the next ten years. At first, the problem of estimating the future of a demand as complex as that for petroleum might appear insoluble. Fortunately, hon~ever, therc are several scientific methods of approaching the problem, centering around a study of rates of industrial growth, which lend considerable hope that the requirements of the immediate future in this field may be approximated with sufficient closeness to have practical value as a basis of action. Growth oF Petroleum Demand The demand for crude petroleum is the resultant of the demands for the products made jointly from this substance—gasoline, kerosene, gas and fuel oil, and lubricating oils. The demands for these have grown at

Jan 1, 1923

By Frank B. Gilbreth

The problem of the crippled soldier in industry is not a problem of war work only; it is a problem of industrial development. As individuals, each one of you is seeking to provide our maimed heroes with such teaching as will render them, in the shortest possible amount of time, productive and satisfied members of the community. As individuals you are interested in the organizations that are preparing to receive these men, to train them and to place them at that work for which they are best fitted. As an organization, it is now your duty to take up the industrial end of the problem, to investigate existing conditions in the industries, to discover where the opportunities for employment lie, and so readjust industrial practice that the cripples may be utilized to their own and the community's good with the least shock to themselves or to the industries, and with the greatest amount of permanent benefit to all concerned. We have divided industrial opportunities suitable for cripples, roughly, into three classes. First, such as already exist in the industries, which can be set aside for cripples only, present occupants being transferred to other work for which they can be fitted but which is not suitable for cripple work; second, opportunities in the industrial world that, through changes in the working equipment or tools, or through appliances attached to the cripple himself, can make the cripple a competitor of the sound worker; third, opportunities not existing at present in the industries, but which could be introduced for the good of the community without placing the cripples into competition with any existing class of workers. As typical of the first type of occupations for cripples, we have mentioned that of store-keeper, of the second type that of typist,2 and of the third type that of dental nurse.3 The last occupation can be so arranged as to take from the overworked dentist the work of cleaning teeth; and

Jan 1, 1918

By M. H. Harris

A solution has been obtained to the problem of calculating flow into a cased and perforated well. Equations describing the idealized system were solved by numerical analysis techniques on a high-speed digital computer. Computer experimentation indicated that the results are within 3 per cent of the exact solution. Computed results are presented as an apparent skin effect, on a series of dimensionless working curves. Productivity ratios can be rapidly calculated from these data for the wide range of wellbore and reservoir properties actually encountered in field practice. Any reasonable vertical unisotropy ratio can be included in the computation. Productivities can be calculated for wells perforated in a regular pattern, a single horizontal plane or a vertical line on one side of the casing. Solutions for asymmetrical perforation patterns can he easily obtained from the working curves. Solutions for flow into sells completed with a horizontal notch are also provided. Results show that productivity can be increased by extending perforation penetration. This is especially true for shallow penetrations. The highest productivity is obtained when perforations are arranged in horizontal planes, as opposed to a vertical line on one side of the casing. Four or five perforations in one plane will approach the maximum productivity. The effect of perforation hole diameter is small, and is rioticeable only in shallow penetrations. INTRODUCTION The perforating method of well completion has been successfully and widely used in most producing areas. In the past, the desired perforation results were achieved by simply shooting numerous large holes in the casing. A perforating scheme for an area, or particular well, was established by evaluating two types of experimental data: the well flow index and the productivity ratio.' 3 The well flow index test is a means of determining the relative flow capacity of perforations in a linear system. This test also gives information on the perforation size, shape and hole damage which can be expected under well-bore conditions. However, relative flow data from this test cannot be accurately tarnsformed into the radial wellbore system. Thus, no true indication of the productive capacity of a perforated well can be obtained from the well flow index test. A well productivity ratio is derived from electrolytic models built to simulate perforated wells. Available productivity ratio data 2,3 are limited in that all important variables are not extensively evaluated. For example, data are limited to well radii of 3 and 6 in., and to maximum perforation penetration of 1 ft. Practically no information is available on the pattern of flow into a perforation. The effect of various perforation patterns on well productivity has not yet been determined and the effect of perforation diameter has not been thoroughly studied. Also, it will be shown that this type of electrolytic model data is probably in error by as much as 10 per cent or more. Modern completion techniques such as limited-entry perforating, single-plane fracturing, steam and hot air injection and chemical consolidation of incompetent formations all rely on injection and/or production from a limited type of completion. These completions may consist of several high-capacity perforations or a horizontal notch which is equivalent to an infinite number of perforations in one plane. Proper design of these new completion techniques requires, in part, accurate estimates of a well's productive capacity. Data on perforated and notched well productivity have been determined in this investigation. Results are presented as a function of the pertinent variables. Equations describing the idealized system were solved by numerical analysis techniques on a high-speed digital computer. DESCRIPTION OF PROBLEM PRACTICAL APPLICATION The computed results can be applied to wells which meet several general specifications. An external drainage radius of the well must be known or assumed, but the well need not be drilled on a regular pattern. The well must be cased and cemented through the entire producing interval. And, the casing must be perforated with one or more horizontal planes of perforations. The perforation pattern itself must conform to three geometrical requirements. 1. The perforations in a plane must divide the plane into equal angular segments (Fig. 1). Four perforations per plane would be 90" apart. 2. Perforations in a plane must be directly above or beneath perforations in adjacent planes. For two shots per plane, perforations would lie in the BB' plane (Fig. 1). 3. Horizontal planes must have equal vertical spacing and be separated from the top and bottom of the formation by one half the spacing interval. Single planes of perforations should be in the middle of the formation. This is shown in Fig. 2 where h is the formation thickness in a single plane conlpletion or the spacnig interval in a multiple plane completion. The spacing interval at the top and bottom of the formation may vary somewhat without causing an appreciable error in the productivity calculation if the formation is reasonably thick and there are many horizontal planes of perforations. A special provision has been made to calculate the productivity ratios of wells with uneven spacing intervals, or for the case where a single plane of perfora-

Jan 1, 1967

RUSSIA was the United States Number One source of manganese ore in 1948 when 34 pet of imports were received from that source, stated Norwood B. Melcher, assistant chief, ferrous metals and alloys branch, Bureau of Mines. In 1949, this country received only 20 pet of 1948 shipments from Russia, and only token amounts are now being received. Aggressive programming by industry and government resulted in prompt increases in shipments from major, producing sources; India, Gold Coast, and the Union of South Africa all increased exports to fill the vacuum left by Russia and provided an excess adequate to increase total imports approximately 290,000 short tons in 1949. Again in 1950, and with, even less ore from Russia, imports increased another 290,000 short tons. Since the shift from Russia as a source of manganese, the United States has received in total about 85 pet of its imports from India, Union of South Africa, Gold Coast, and Brazil in that order of importance. Producers of both home consumed and merchant ferromanganese have been able to adjust downward the manganese content of the home-consumed product and so obtain partial relief. Millions of tons of steel were produced in 1951 with a relatively low grade ferromanganese. This adjustment has been made without decreasing the quality of the steel, although with some increase in cost through introduction of new problems, including increased hand- . ding of material and additional removal of carbon. Forced into a pattern of price and grade structure such as exists today, the producer of ferromanganese must adopt one of three possible courses as a short-range program: 1-He may continue to deplete his stocks by producing standard (78 pet) ferromanganese and hope that the future will bring some form of relief; 2-he may attempt to produce 78 pet ferromanganese by paying higher prices for premium ores; or 3-he may drop the grade of ferromanganese and stretch stocks and future supplies of ore as far as possible. The present rundown condition of Indian railroads is attributed to the fact that the service has had no opportunity to recuperate since the beginning of World War II, while the demand for the movement of commodities has probably increased. The Union of South Africa has expanded its exports to the United States greatly since 1948, but, the showing of that country in 1951 was disappointing. Efforts have been made for some time by firms in the United States, at the urging of the manganese miners in the Union, to prevail on the railroad authority to grant and make available larger allocations of cars for manganese ore movement. As a whole, such efforts have been unsuccessful. Although the allocation of rail shipping has been the obvious factor in the decreased movement of ore, many other less determinate factors appear to be involved. Brazil, long an important supplier of manganese to the United States, has important manganese deposits in three areas, all of which are significant to this country. The Gold Coast is an important source of supply. Its metallurgical ore is particularly of significance because of its unusually high grade which permits considerable latitude in blending with the lower grade materials of South Africa and India. The Belgian Congo should have an output of 100,000 tons or more annually beginning this year. R. S. Dean presented two papers. One with K. M. Leute on hydrometallurgical methods for recovery of manganese from domestic ores and one as sole author on the so-called carbamate or Dean process. The two papers tied into each other. In the first mentioned he reviewed the various processes applicable to oxidized, and nonoxidized and reduced ores. The advantages of each .were pointed out. So far the only process tried on a substantial scale on oxidized ores was the SO2 process used at Las Vegas, Nev., on Three Kids ore during World War II. Many problems were encountered. Some of them were whipped while some of those remaining perhaps would have been whipped had time permitted. Since then work has been done elsewhere to avoid the formation of the troublesome thionates encountered at the Three Kids plant. Dean discussed the thionate and NO, processes as applied to oxidized ores. The only commercially used process on reduced ores is that of making electrolytic manganese. Among others that have been considered are the nitric acid process, the Bradley-Fitch ammonium sulphate process, and Dean's ammonium carbamate process. Dean's thesis was that extremely large tonnages of so-called low grade manganese ores are available, and that these should not be depleted in attempting to simulate a foreign metallurgical grade ore. He pointed out that the grade of the domestic manganese ores would be considered high if the same grade were found in copper ores. The selling price of electrolytic manganese and electrolytic copper are roughly the same. In addition to electrolytic manganese, he believes that domestic ores should be used to make exceptionally high grade products. These might be battery grade oxide or substantially pure oxide sinter, which might be used for high manganese alloys or for upgrading metallurgical grade manganese to produce a high manganese ferroalloy. The carbamate process is based on the fact that manganous oxide is readily soluble in concentrated ammonia solutions containing ammonium salts. In solutions of sufficiently high concentration the manganese exists as an anion. Lixiviants of ammonia and ammonium carbonate permit extraction of the manganese from reduced ores and the manganese can be recovered as carbonate by heating or by driving off ammonia. R. V. Lundquist presented a paper on upgrading high-silica ores or concentrates with sodium hydroxide to extract silica and to yield a product with a more favorable manganese: silica ratio. The NaOH is, regenerated in part by CaO.

Jan 1, 1952

By F. Weinberg, E. H. McLaren

Dilute binary alloys have been solidified under controlled thermal conditions, and solute distributions, temperatures during freezing and melting, and the position and morphology of the solid-liquid interfaces have been examined. Binary Zn, Sn, and Pb based alloys were investigated with solute additions of AgU°, AU°, Sb'24, TlZo4, snH3, and Zns5. Approximately 150 cc of metal was used in each ingot. Appreciable solute segregation occurred in most of the ingots, depending on the solute concentrations, distribution coefficients. and freezing conditions of the alloys. Measurements were made of the general solute distribution by sectioning layers of material from the ingot circumference and counting the activity of each layer. Local segregation was detected by autoradiographic techniques. Freezing and melting curves for the same alloys were obtained by precision resistance thermometry. These curves are related to the corresponding measured solute distribution curves and those calculated from theoretical expressions. The position and morphology of solid-liquid interfaces during freezing were determined by both decanting and quenching techniques. The results indicate the manner in which freezing and remelting occurred under the conditions investigated. If an isomorphous dilute binary alloy is solidified or melted under equilibrium conditions, the concentration of solute in both solid and liquid would be uniform at all stages in the freezing process. The solute concentrations during freezing could be determined from the phase diagram of the alloy, and the freezing curves would have an alloy slope defined by the solidus and liquidus points. In practice, however, solidification under equilibrium conditions rarely, if ever, occurs, primarily because of low rates of diffusion in the solid and incomplete mixing in the liquid. As a result, the solute distribution and the shape of the freezing and melting curves obtained in a given system depends on a number of factors. These include, in addition to the extent of diffusion and mixing, the initial solute distribution and concentration, the distribution coefficient, the rate of freezing or melting, supercooling of the liquid, the morphology of the solid-liquid interface, and the effect of annealing. The purpose of the present investigation was to determine, experimentally, actual solute distributions and thermal curves for a series of dilute binary alloys, using tracer techniques to determine the solute distributions and precision resistance thermometry for the temperature measurements. In addition, observations were made of the positions and morphologies of the solid-liquid interfaces during freezing and remelting. The distribution of solute in a dilute alloy, assuming complete mixing in the liquid, and negligible diffusion in the solid, is given by1 where Co is the mean solute concentration of the alloy, C, is the solute concentration in the solidg is the fraction of the ingot solidified, and ko is the equilibrium solute distribution coefficient (assumed to be independent of concentration for dilute alloys). For the case of partial mixing, ko can be replaced by an effective distribution coefficient k. If solute transport in the liquid is assumed to be entirely due to diffusion, with negligible diffusion in the solid, then the solute distribution in the solid is given by Tiller et a1.' as where R is the rate of advance of the solid-liquid interface, D is the solute diffusion coefficient in the liquid, and x is the position of the interface from the start of freezing. The temperature at the interface TI is related to the solute concentration of the solid at the interface C, by the expression where Tm is the freezing temperature of the pure solvent and ml is the slope of the liquidus for the binary alloy being considered. Accordingly, by relating TL to the actual temperatures measured in the present experiments, solute distributions can be deduced from the temperature measurements. Using the above expressions, the measured solute distribution of a given alloy may be compared to the theoretical distributions, as well as to the distribution calculated from the observed freezing curve. EXPERIMENTAL The solvent materials used in making up the binary alloys were C. P. New Jersey zinc (99.999 pct), Vulcan Extra Pure Tin (99.999 pet), and Tadanac lead (99.998 pct). The solute elements were of 99.99 pct purity or better, and were activated in the

Jan 1, 1963

By J. U. Messenger

A technique is described whereby the resistance of an emudian to breaking can be quantitatively determined. Produced ailfield emulsions are usually the water-in-oil type and, accordingly, do not conduct an electrical current. However, there is a threshold of A-C voltage pressure above which an emulsion will break and current will flow. The more stable an emulsion, the higher the required voltage. A Fann Emulsion Tester, modified so that low voltages (0 to 10 v) can be accurately measured, is suitable. This technique has application in evaluating the effect of a demuksifier on the stability of an emulsion. Emulsions can, in essence, be titrated with demulsifiers by adding a quuntity of demulsifier, stirring, and measuring the voltage required to cause current to flow. Any synergistic effect of two or more materials added simultaneously can be followed accurately. A demulsifier that significantly lowers the threshold voltage (from 100 to 400 v to 0 to 10 v for the emulsions in this study) is effective and can cause the enlulsion to break. A demulsifier that will bring about this drop in the threshold voltage at low concentration ir very desirable. The technique is also well adapted for rapidly screening demulsifiers. INTRODUCTION Stable emulsions in produced reservoir fluids resulting from certain well stimulation and completion procedures are common problems. The use of suitable demulsifiers can often mitigate these difficulties. At the present time, a rapid and efficient method for selecting satisfactory demulsifiers is not available. It is badly needed. Reliance is now placed primarily on trial-and-error procedures. A new test method has been developed which permits a more rapid and precise selection of demulsifiers. It involves measuring the electrical stability potential of an emulsion before and after a demulsifier has been added. This paper describes this method and shows where it should have application in field emulsion problems. NATURE OF OILFIELD EMULSIONS Two immiscible components must be present for an emuhion to form; we are concerned here with crude oil and water. An emulsifier must be present for tin emulsion to be stable. J Emulsifiers can be substances which are soluble in oil and /or mter and which lower interfacial tension. They can be colloidal solids such as bentonite, carbon, graphite, or asphalt which collect at the interface and are preferentially wet by one of these phases. Unrefined crude oils can contain both types of emulsifiers, A popular theory is that, of the two phases in an emulsion, the dispersed phase will be the one contributing most to the interfacial tension.' Usually this phase contains the least amount of emulsifier. The stability of a water-in-oil emulsion is affected by the fol1owing: l) viscosity; (2) particle or droplet size; (3) interfacial tension between the phases; (4) phase-volume ratios; and (5) the difference in density between the phases. A stable emulsion is usually characterized by high-viscosity, small droplets, low interfacial tensions, small differences in density between its phases, and slow separatian of the phases. It also has low conductivity (high electrical stability potential). Water-in-oil and oil-in-water emulsions"' are both common; however, oil field emulsions are predominantly water-in-oil emulsions. The emulsions which commonly occur during oompletion and stimulation operations contain a combination of several of the following: acids, fracturing fluids (oil, water, acid), and formation water and oil. Produced emulsions usually contain formation water and oil. Emulsions form in oil wells because oil and water are mixed together at a high rate of shear in the presence of a naturally occurring or unavoidably produced emulsifier. During the completion and stimulation of productive zones, and while formation fluids are being produced, oil and water are very often commingled. These mixtures are formed into emulsions by agitation which occurs when the fluids are pumped from the surface into the matrix of the formation or produced through the formation to the surface. Restrictions to flow (such as perforations, pumps, and chokes)".'" increase the level of agitation; tight emulsions are more likely to form under these conditions. Often an emulsified droplet is an emulsion itself.'" Therefore, emulsion-breaking problems can be quite complex. The complexity can be even greater if a third phase (gas) is included. Demulsifiers operate by tending to reverse the form of the emulsion. During this process, droplets of water become bigger, viscosity is lowered, color becomes darker, separation of the phases faster and electrical stability potential approaches zero. Any of these effects could be followed as a means of determining emulsion stability. However, electrical stability potential is the most reproducible and most easily measured parameter for following the stability of a water-in-oil emulsion.

Jan 1, 1966

By R. H. Schnitzel

Internal-friction peaks have been observed in tungsten single crystals at about 300° and 400°C. The characteristics of these peaks are similar to interstitial peaks observed in other bee metals; therefore, the origin of these peaks appears to he the Snoek mechanism. The interstitial responsible for the peak at about 300°C has not been identified. Carburizing increases the magnitude of the peak at about 400°C; consequently, it appears reasonable to suppose that the specific interstitial associated with this peak is carbon. The activation energies associated with the 300° and 400°Cpeaks are about 35,000 and 45,000 cal per mole, respectively. INTERNAL - friction peaks resulting from the stress-induced diffusion of interstitials (Snoek relaxation peaks) have been frequently observed in bee metals.1-5 Attempts to detect Snoek relaxation peaks in tungsten have, however, not been fruitful.' Failure to find Snoek peaks in sintered tungsten can perhaps be attributed to one or more of the following difficulties: a) the relatively low purity of the sintered tungsten; b) the lack of extensive metallurgical knowledge about tungsten-interstitial alloys, such as suitable interstitial dosing and quenching procedures; and c) the inconsistency of some of the interstitial analyses of tungsten, which reflects itself in one's inability to be sure of the nature of the specimens. This present investigation did not overcome all of these difficulties for successful tungsten internal-friction measurements. Some of these difficulties still persist and new difficulties were encountered during the course of this investigation. Nevertheless, the use of electron-beam tungsten single crystals having somewhat greater purity levels than sintered tungsten combined with appropriate carburizing and quenching procedures permitted a reasonable attempt to be made. As a consequence, internal-friction peaks were observed in these tungsten single crystals at about 300° and 400°C. These peaks were found to be unstable, since they annealed rapidly away during a sequence of internal-friction measurements. Hence, it was necessary to construct an apparatus having a faster heating rate to study some of the details of these peaks. From the behavior of these peaks as well as our knowledge of similar peaks in other bee metals, one can reasonably conclude that these peaks are caused by residual interstitial impurities within these crystals. Further investigation of these peaks after the application of various metallurgical treatments lent credence to this supposition. EXPERIMENTAL TECHNIQUE The internal friction of tungsten single crystals was measured using two different pieces of apparatus both of which are of essentially the same conventional design, namely the KE type of torsion pendulum. The important difference between these two types of apparatus was in the attainable heating rate and method of protection of the specimen from atmospheric contamination. The apparatus designated "number 1" was enclosed in a vacuum chamber which was heated by an externally mounted furnace. It had a slow rate of heating which was estimated to be about 4°C per min from room temperature to about 350°C and then about 1°C per min to 600°C. The internal friction of tantalum was measured with this apparatus and the established Snoek peaks were found.' These tantalum peaks in the temperature range from room temperature to 400° C served as a check for the apparatus. The apparatus designated "number 2" having a faster heating rate than number 1 was not elaborate. It consisted of a mounted nickel tube to which split heating elements were attached. Argon was used as the protective atmosphere. The measured heating rate was about 12° to 15°C per min whereas the cooling rate was somewhat slower at about 10° C per min because of the increased difficulty encountered in stabilizing the temperature. No surface oxidation of the specimen was noted after any test. This apparatus was also checked with the known peaks of tantalum.1 The preparation of the single-crystal specimens for internal-friction measurements consisted of centerless grinding the crystals from an approximate 0.200 in. diameter to 0.030 to 0.040 in. in diameter, and then electropolishing them to about 0.020 in. in diameter. Single crystals processed in this manner are designated as being in the virgin condition. Since the length of crystal varied from 3 to 9 in., the test frequency varied from about 1 to 2 cps. The frequencies of measurement, axial orientations, and chemical analyses for the various crystals are listed in Table I. The controlled addition of carbon into tungsten is a difficult problem. Attempts to find the critical conditions necessary for an equilibrium treatment were not fruitful. Therefore, a simple nonequi-librium method was used. The addition of carbon to these crystals consisted of appropriately combining three treatments—carburizing to achieve a case, annealing to partially dissolve the carbon into the

Jan 1, 1965