Search Documents

"The Tooele plant is situated at the mouth of Pine Canyon, five miles northeast of Tooele City. The site forms one terminus of the Tooele Valley railway, which runs southwest through Tooele City to Warner, a station on the Los Angeles and Salt Lake Railroad, thirty-five miles southwest of Salt Lake City.An aerial tramway, four miles in length, crosses the Oquirrh Mountains and connects the plant with the Bingham district.The plant consists of a lead-zinc flotation concentrator, lead smelter and copper smelter.SAMPLING MILL The mill is a standard Taylor and Brunton sampling mill, built in two sections, each with a capacity of 100 tons per hour. The building is of steel and concrete, 40x84 feet. A well-equipped pulping, sampling and drying room is attached.All ore is sampled here and then distributed by conveyors to cencentrator, lead smelter and copper smelter bins.CONCENTRATOR This flotation mill is arranged in two units of 500 tons capacity each, one equipped with Callow pneumatic flotation cells, the other with Mineral Separation sub-aeration machines.The feed is maintained as uniform as possible by bedding, after coarse crushing at the sampling mill. Standard practice of ball mill grinding and classification is followed."

Jan 1, 1925

By George T. Hansen

WHY try to find oil in Utah? Why try to find oil anywhere? Isn't there too much oil already? Answers to these questions involve general oil conditions but are pertinent to my subject. In the first place oil produced in Utah up to the total amount of local consumption would not be subject to nor concerned with the national oil situation. An oil field in this State capable of producing up to 15,000 bbl. per day would have a large value and prompt realization. In the sec¬ond place, there is not too much oil nationally although the markets have been upset temporarily from time to time. Petroleum is so necessary and is in such general demand that an oil field anywhere, anytime, is a valuable and live asset. The oil business in general shows the best condition of any major industry. It has never been hit as hard as most industries and 1932 was a large improvement over its low spot of 1931. It can be and probably will be the one to lead the country back into business stability. Consumption of its products has been reduced less than that of any other important commodity. There are good and valid reasons why it should have been making a normal profit continuously. It has the oil and the processes and the facilities and the policies and the consumption of its products. There is only one reason why it has not been profitable recently and that is the lack of intelligence of from five to ten per cent of the producers. An op¬erator lacks intelligence when he cannot see that it is better for him to sell one barrel of oil at $1 than two or three barrels at 25 or 35c. per bbl.

Jan 1, 1933

By AIME AIME

YOU can place an exclamation point after the "and How" if you want to, but the way it stands it sum¬marizes the Mining Geology sessions quite nicely; "Why" in the morning, "How" in the afternoon. It is altogether fitting that Prof. McLaughlin and Reno Sales, who have themselves achieved enviable reputations in company work, should have led the program by presenting informally a chapter from the volume dedicated to the beloved dean of all economic geologists, Waldemar Lindgren. In opening the morning session, over which Sydney Ball presided, Donald McLaughlin emphasized the continuous role mining geology should play in operating technique. He pointed out the importance of structural relations in a broad sense, and the preponderant role they play in developing the manner of ore occurrences. He illustrated this by an account of the work at Homestake, using slides to show the stratigraphic sequence, the folding, and the orebodies of that camp. An interesting piece of detail was the distinction they found could be made be¬tween the chlorite near the ore masses, and that in the country rocks. Whether the cummingtonite, characteristic of the rock in which the ore is found, is of regional or of contact metamorphic origin caused some discussion. Dr. Lindgren inclined to the belief that it was contact, but L. C. Graton replied that they had found the weight of evidence was for a hydrothermal origin. D. F. Hewett raised the question as to whether, in the advancing development of the mining industry, there was still a place for the U. S. Survey geologist, and the consensus seemed to be that there should be. His role is changing from that of mapping mining districts in detail, now the task of the companies, towards a more general serving of the industry through the wider perspective his work gives him in contradistinction to the greater detail of knowledge accumulated by the resident geologist.

Jan 1, 1933

By J. B. Newsorn

VERTICAL SHAFTS in the United States have heretofore been sunk by blasting and mucking. The blasting leaves uneven, shattered walls which usually must be supported. Even though the walls will stand, shaft lining is needed to furnish supports for the cage guides, pipes, and power conduits. The lining is generally timber, and as timber can be most easily framed into rectangles, rectangular shaft openings are the rule. The timber reduces the size of the cage floor. For example, if the Idaho Maryland company had put down No. 2 shaft by blasting and mucking, the cage area would have been about thirty per cent of the total shaft area. Besides a low percentage of useful area, an ordinary shaft is subject to fire hazard and to timber maintenance charges. It is also poor for ventilation because the timber ribs cause eddies which greatly reduce the speed of the air currents. A bored shaft does not have these disadvantages. The walls are smooth, circular, and not shattered by blasting, so lining is not required in most

Jan 1, 1936

Jan 1, 1977

By Charles Camsell

MORE than one-third of all Canada is embraced in the federal domain known as the Northwest Territories. Its most northern point, Cape Columbia, on Ellesmere Island, is only 500 mi. from the Pole. It includes parts of the main physiographic divisions of the North American continent. In the West there is a strip of 30.000 sq. mi. lying in the Cordilleran region, where peaks in the Mackenzie Mountains rise as high as 8500 ft. East of this strip and extending roughly to a line through Great Bear and Great Slave lakes to the Arctic coast is a section of the interior plains. This section, known as the Mackenzie Lowlands, contains the great artery, the most striking feature of the Northwest Territories-the Mackenzie and Slave river waterway impressive in its width, almost two miles in places, and in it's navigability for 1357 miles without obstruction to the sea. Adjoining the Mackenzie Lowlands on the East is the greater portion of the mainland of the Territories, which, as well as a large share of the island area, is in the Canadian Shield.

Jan 1, 1937

By Stanley C. Herold

TWENTY-FIVE years ago no distinction was made between water wells and oil wells except in the nature of the fluid produced. Water wells usually showed no decline in their rate of production; when oil wells showed decline something in the manner of handling them was considered wrong. Both water and oil were believed to be subject to the same physical laws in their underground movement toward the wells. Today a sharp distinction is made between them. Whereas water exists alone in the porous formations at depth, oil is usually accompanied by gas. This mixture does not behave as a liquid alone. It is a frothy, seething mass of foam which approaches and enters the wells. Different physical laws come into play. Twenty-five years ago attention was directed entirely to the well itself; today the well is accepted as a mere hole in the ground, a hole to be equipped properly for efficient service, yet without any value whatever unless it is backed up by a sufficiently prolific reservoir. Then, we were concerned with wells alone, 3000 ft. in depth; now commercial wells and their reservoirs are 10.000 ft. deep. Petroleum engineering concepts have necessarily therefore undergone a change in this last quarter century. What are they today?

Jan 1, 1937

By Anal J. Mehta, Theodore D. Tiemann

Growing demand for steel and increasing dependence upon foreign ore makes the need for developing the technology for treatment of low-grade iron ores greater than ever before• Representative of these added interests were the studies carried on at the University of Wisconsin• These studies included among others: anionic and cationic flotation, magnetic separation, roasting followed by magnetic separation, electrostatic separation, a hydrogen reduction process,6,7 and caustic digestion• The idea of removing silica by caustic extraction is not new•-1; The principle of concentrating siliceous iron ores by this method is based on the fact that silica is soluble in sodium hydroxide solution while iron oxides are essentially insoluble• For this process to be economically feasible, it is believed that some method of recovering silica from solution as a marketable by-product, with recycling of spent liquor is necessary. Precipitation of silica with carbon dioxide will allow subsequent causticizing of the spent liquor with lime• Caustic thus produced can be recycled for digestion• A flowsheet of the envisioned process is given in [Fig• 1] The purpose of this paper is to describe results obtained from the investigation of carbon dioxide precipitation of silica from sodium silicate solutions, which could be later applied to the caustic extraction process to treat low grade siliceous iron ores, particularly taconites.15 Theoretical Considerations The soluble silicates of sodium include sodium orthosilicate (2Na2O•SiO2), sodium metasilicate (Na20•SiO2), sodium disilicate (Na1O•2SiO2), and more highly siliceous products approaching Na2O•4SiO2• These materials have been described in detail by Vail•16 Stones has reported that the extraction of silica is not significantly affected by the amount of silica in solution until the Si02/Na20 ratio exceeds that of orthosilicate (Ratio = 1/2)• However, as the Si02/Na2O ratio exceeds that of metasilicate (Ratio = 1), silica extraction is significantly impaired• The present experimental work was confined to orthosilicate and metasilicate solutions, as to be successful the envisioned commercial process for the extraction of silica from siliceous iron ores would operate in this region. The mechanism of extraction of silica from aqueous sodium silicate solutions is complex in nature. For the carbon dioxide process-18 of core and mold making in which silica is also precipitated from sodium silicate solutions by gassing with carbon dioxide, the reaction of aqueous silicates with gaseous carbon dioxide has been represented by the equations: [ ] However, these equations are very much oversimplified• It has been shown that the reaction between aqueous sodium silicates and carbon dioxide gas is ionic in nature 18 Considering this fact and the mechanism for digestion of silica in aqueous sodium hydroxide, the overall conversion of aqueous sodium silicates to solid silica may be represented in ionic form by the following equations: [ ] Silicon in the silicate ion is shown here with a coordination number of 6• This may be in doubt, but it is known that ion (SiF°)-2 exists; it seems logical that the Si (OH) e 2 ion should be equally capable of existence•

Jan 1, 1977

MARSHAL Foch has been made an honorary member of the four national American societies of civil, mining and metallurgical, mechanical, and electrical engineers. The governing bodies of these societies, aggregating 45,000 members, conferred this signal honor in expression of the appreciation of American engineers for the unmatched services of this master of engineering principles. At Engineering Societies Building, in New York City, on Tuesday afternoon, Dec. 13, the presidents of the four societies presented one beautifully engrossed certificate of honorary membership in the four societies. The auditorium was filled so that not even standing room was left, more than a half hour before the cere-monies began, and the main entrance on the street had to be closed. J. Vipond Davies, president of the United Engineering Society, made the opening address. Col. William Barclay-Parsons, 'who was commander of the first engineer regiment to go abroad, addressed Marshal Foch in French. Colonel Parsons said: The art of engineering was defined a long time ago as "the art of directing the great sources of power in nature for the use and convenience of man." No better definition can be found today. Of all the sources of power in nature, the greatest, the most valuable, and at the same time the most difficult to direct, is the energy of man himself. He who can direct human energy and turn it to the service of mankind is a great engineer. You, Marshal, have directed a greater mass of human energy than any other man has ever done. And you have successfully directed this mass for the highest uses of mankind, in that you by its aid have preserved for him one of the most precious of human possessions-liberty-liberty not only for your own illustrious country, but for all the nations of the world. The four national engineering societies, of the United States now desire to make record of their appreciation of this fact and to convey to you an expression of their most profound admiration for the great leader of men by conferring on you honorary member-ship in all the societies, the highest honor in their gift and one hitherto never conferred on a single individual. Four thousand members of these societies were enrolled in the armed service of the United States, the greater part of whom had the glorious distinction to serve the common cause in France under your orders. They heard the voice and they saw the hand of the master as he led them through battle to victory. Now we desire that you will still continue to lead us, but in peace, by permitting us to inscribe your name at the head of our roll of honor, where it will be, as your deeds have been, an example to us to do better work, and where it will remain forever a noble inspiration for all future generations. Marshal, in the name of those members of the societies who served under your orders and particularly .in the name of those who fell on the field of honor in France, I salute you.

Jan 1, 1922

By N. F. Foster

The use of piezoelectric semiconducting materials for the fahrication of ultrasonic transducers has raised the upper fundamental frequency limit for transducers from about 200 mc to above 10 kmc, Several types of semiconductor transducer configurations have been proposed and examined experimentally. Depletion-layer transducers have been made and operated at frequencies below 1 kmc hut they appear to he better suited for operation at considerably higher frequencies around 10 knzc. Diffusion-layer transducers have been made and operated in the range 50 to 1000 mc and have exhihited considerably improved conversion losses and bandwidths compared with other transducers available in the frequency range. A variety of novel structures are possible using these new types of transducers, some of which could lead to substantial advances both in research and in the fabrication of ultrasonic delay lines and memory elements. THE field of ultrasonics today spans some five decades of the frequency spectrum from the audible to the kmc range and finds applications ranging from fundamental research into the atomic structure of matter to the degreasing of machine parts. To cover this wide range it has been necessary to develop a great many types of ultrasonic trandsucers utilizing a variety of materials and physical phenomena. The first ultrasonic transducers were made during World War I for a submarine-detection system. They consisted of plates of single-crystal quartz bonded between metal plates and were one of the first applications of the phenomenon of piezoelectricity discovered nearly 30 years previously. Despite the many advances which have been made in transducer technology, piezoelectric transducers using single-crystal quartz are still used almost exclusively for application above about 30 mc. Transducers at these frequencies are normally made in the form of thin quartz plates which are then bonded onto the medium in which the ultrasonic wave is to be propagated. The crystallographic orientation and geometry of these plates determines the type of wave generated and the way in which the efficiency of the electromechanical conversion varies with frequency. Analysis of the design parameters shows1 that the frequency of maximum efficiency (the fundamental or resonant frequency) is that frequency at which the transducer is approximately half the wavelength of the ultrasonic wave in the material. As the frequency increases, the ultrasonic wavelength, and therefore the optimum transducer thickness, decreases and in practice the fabrication of quartz transducers with fundamental freauencies above 100 mc becomes extremely difficult due to the extreme thinness required. For frequencies above 100 mc quartz transducers can be used in overtone-mode operation, and for very high frequencies (500 to 24,000 me) a technique using a quartz rod inserted in a high-Q microwave cavity4 is available. These techniques, however, exhibit comparatively low fractional bandwidths and rather poor conversion efficiencies. The present trend in ultrasonics is towards high frequencies and greater bandwidth to allow the use of shorter pulses which can give increased discrimination in radar-system delay lines and greater storage capacity in computer applications. The increasing demand for more efficient transducers with greater bandwidth

Jan 1, 1964

H. H. Campbell, Steelton, Pa. (communication to the Secretary) : I wish to thank Mr. Webster for the copious quotations he has made from my writings, as he has given nearly all the arguments I wish to advance. It is necessary to note, however, his statement that most of his experiments were made on universal-mill plates, and that these were not subject to my condemnation of irregularity. I think this is a mistake. It is well known that universal-mill plates are finished under very different conditions of temperature, with the express purpose of regulating the tensile strength. This is a perfectly legitimate practice; but it renders almost worthless any calculations on the relations of the chemical and physical equations when the influence of such finishing is omitted. Another important point Mr. Webster has not answered at all. I have shown by an excerpt from his own table that two entirely different formulæ may be constructed; and it is undeniable that one is as valid as the other, since Mr. Webster started with no premise at all save an assumption that the effect of carbon was constant. This was an assumption pure and simple, and hence has no special virtue. The whole result of Mr. Webster's investigation is not that the effect of carbon is a constant, and that those of phosphorus and manganese are variables. On the contrary, there are two answers, with nothing to show which is right. We learn that if carbon is a constant, then phosphorus and manganese are variables; but that if phosphorus and manganese are constants, then carbon is a variable. This is a distinct advance over complete ignorance, but it is not final and satisfactory from either a mathematical or metallurgical standpoint. Regarding my own formulæ, I would say that they are used regularly in the testing-laboratories of the Pennsylvania Steel Company. The tensile strength of every heat is calculated

Jan 1, 1899

By J. C. METCALF

MORE than 80 per cent. of the iron produced in the United States and over 30 per cent. of the world's annual production is obtained in the Lake Superior district. Though iron ore was discovered on the Marquette range in 1844, the poor transportation facilities retarded the development of this region for many years. The structure of the Lake Superior basin is essentially an east-west synclinorium with steep dips on the south side of the lake and considerably flatter ones on the north and west. The Upper Huronian series, which -is the iron-bearing one of the formation, on the south side of the lake dips north from 55' to 80°, and on the north side dips south from 8" to 200. The series has been subjected to local folding and faulting, which have influenced the development of the mining systems used.

Jan 1, 1921

By Anthony Anable

HOOVER DAM, rapidly nearing completion in the Black Canyon of the Colorado River at Boulder City, Nev., taxes the superlatives of the vocabulary to describe. For by all odds, it is the largest construction project of its type ever essayed by man and the plants providing the essential materials of construction are also in a class by themselves not only in size but in advanced design, mechanization, and accurate control. Picture, if you will, the great aggregate plant, as it is called, situated about 4 mi. upstream from the site of

Jan 1, 1934

By REED H. HYDE

IN these days of low metal prices and difficult marketing conditions, any treatment that will improve the grade of a product is of interest, particularly when the operation involves little or no addition to the total cost and may even result in a marketable by-product. Such a' combination of circumstances exists, in some cases, in the zinc industry, where it has been found that certain impurities can be removed from .the ore during the Dwight-Lloyd sintering operation, previous to reduction to metal. Consequently it is not surprising that zinc smelters having these sintering machines are paying particular attention to this phase of the operation. Loss of zinc as fume is very low under the conditions obtaining in sintering zinc ores, but impurities such as cadmium and lead are more readily fumed off and it is on this fact that the purification is based. As a result of preferential volatilization of these impurities a sintered product' is made from which purer zinc metal or oxide can be produced, while the fume may be collected and treated to recover the impurity metals. To be effective the operation must be carefully conducted, but no special equipment other than that of a well designed Dwight. Lloyd plant is needed.

Jan 1, 1931

By AIME AIME

IT is unlikely that any oil field has ever threatened the future course of the oil industry as does Kettleman today. It seems that nature has striven to outdo herself in combining in this field every possible factor conducive to a tremendous production of the petroleum product in greatest demand-gasoline. This field already has 13,700 acres of proved land and an oil zone of known thickness of 1400 ft. It has wells yielding several thousand barrels of oil of virtually motor fuel grade, together with millions of cubic feet of gas at almost unheard of pressures. The field would have been the. answer to an oil man's prayer in times of under-supply, but now it is the oil man's nightmare, for drilled in -the manner of most other fields and without regard to available markets for oil and gas, the greatest physical and economic losses in the his¬tory of the oil industry will result.

Jan 1, 1930

By W. B. Gogarty

With flow of non-Newtonian fluids in porous media, effective viscosities are needed for use in the Darcy equation. These viscosities depend on the rock parameters and flowing conditions. In this investigation, rheological and flow results were correlated to develop an expression for calculating effective viscosities. Surfactant-stabilized dispersions of water in hydrocarbon were used with consolidated sandstone cores of different permeabilities. The average shear rate in a core was related to the permeability and porosity of the core and the frontal velocity through the core. By using the correlation obtained for determining effective viscosity, experimental and theoretical values were compared for each fluid system by determining average and maximum errors. For the fluid system showing the largest average error, the correlation fit 38 experimental points with an average and maximum percentage error of 4.3 and 14.8, respectively. For the fluid system showing the least error, average and maximum percentage errors of 1.8 and 4.3, respectively, were calculated using 29 experimental points. INTRODUCTION Use of non-Newtonian fluids in the petroleum industry is not new. Fluids of this type have been used for many years as fracturing agents and drilling muds. Recently, attention has focused on the use of high molecular weight polymer solutions for secondary recovery. Results have been reported on studies relating to the flow behavior of polymer solutions in porous media.1-4 Each study gives the viscosity in the Darcy equation as a function of the rheological properties of the fluid, the characteristics of the porous medium and the pressure gradient. The functional forms of the reported expressions differ somewhat in each study. The first three studies used unconsolidated porous media while the fourth used a single consolidated core. Because of the limited information available on the flow of non-Newtonian fluids in porous media, further investigation was undertaken in this area. We selected non-Newtonian fluids that did not contain high molecular weight polymers in order to minimize core plugging. The over-all objective was to gain a better understanding of the flow behavior of non-Newtonian fluids in consolidated porous media. Specifically, our goal was to determine the relationship between the average shear rate in a core and the frontal velocity. Because of this goal, it was necessary to determine the effect of permeability on the shear rate-frontal velocity relationship. We wanted to replace the viscosity in the Darcy equation with an expression relating to the average shear rate in the core and the rheological properties of the non-Newtonian fluid. THEORY For a time-independent, non-Newtonian fluid, the apparent viscosity is a function of the shear rate. This relationship is given by µ = F(v')...........(1) With Eq. 1, a single value of shear rate determines the apparent viscosity at that shear rate. With flow in porous media, a spectrum of shear rates occurs at any average throughput. An average shear rate v' can be used to represent the spectrum of shear rates that exists within the core. By using v' and the rheological data given by Eq. 1, an effective viscosity is determined for the flowing fluid. If v' is the correct average, µe becomes the appropriate viscosity for use in the Darcy equation. Under these conditions, flow rate-pressure drop relationships can be determined for non-Newtonian fluids. HOW the correct average shear rate might be related to the frontal velocity through the core and the characteristics of the porous media will now be considered. Later, the experimental data are presented that indicate the validity of these

By M. H. Childs, K. E. Merklin

Blast furnace feed specifications are being revolutionized because of the large increase in iron pellet production from low-grade ores of the Lake Superior region. Recent laboratory findings aimed at a better understanding of factors influencing the physical quality of pellets produced from taconite concentrates are reviewed. Tests for determining better product quality, the effects of additives, and production factors are discussed. The current revolution in specifications for blast furnace feed is typified to a great extent by the recent tremendous growth in iron ore pellet production from low grade ores of the Lake Superior region. Indeed, pellets are responsible, at least in part, for many of the stringent new requirements that are being placed on the suppliers of furnace raw materials. As the tonnage of pellets going to the steel mills increases, more and more attention is being turned to the detailed characteristics that make this product an ideal blast furnace feed. Control of quality in pellets is similar to that of any other product. A basic understanding of the factors that are encountered in their production, from the crude ore through to the finished product, is required, along with careful process supervision and frequent quality checks. Normally, chemical grade is not a problem. This usually can be controlled within the desired specifications by minor operating variations in the con- centrator. While future changes in requirements may result in the need for self-fluxing pellets1 or other chemical changes, today's quality demands center primarily around the physical characteristics of the pellets. It is in this area that many of the recent laboratory studies have proven helpful to the operating plants. A better understanding of the physical factors involved in pelletizing has provided the basis for a continuing program of quality improvement. Tigerschiold and Ilmoni2 and Cooke with various associates are responsible for the development of much of the basic understanding of the pelletiz-ing process. These earlier findings have served as a most useful background for this work. LABORATORY PROCEDURES Magnetite concentrates produced from eastern Mesabi Range magnetic taconites were used for all of the work reported herein. The sizing and chemical analysis of a random sample are shown in Table t Additives usually are mixed with the concentrates in taconite plants before pelletizing to improve the strength characteristics of the unfired balls. Ben-tonite, soda ash, and coal are in common use. The bentonite used in these studies was of the Wyoming sodium type; the soda ash was a standard commercia1 brand. Anthrafines were used where coal was called for. The procedure for making batches of balls at the Hibbing Laboratory is as follows: In an especially designed mulling equipment 2800 g of dry ore are mixed for 10 min with the desired additives. Water is added and mixing continued for 1 1/2 min. The charge is removed from the muller and put through a mechanical shredder to break down any lumps that may have formed. sixty previously formed seed balls are placed in the balling drum, which is in fact a 6 x 16-in. diam airplane tire turning at 53 Wm. Two thousand grams of the shredded concentrate and additive mix are fed by hand into the tire at a con-

Jan 1, 1961

By Norman D. Fitz, Gerald

BOTH physical and economic factors are concerned in determining the optimum rate of depletion of a mineral deposit. The physical limitations are, in a large measure fixed by nature. Economic influences on the other hand, are man-made and subject to wide changes. Analyses of the interrelations of these two groups of factors are of major importance in selecting the optimum rate of production of petroleum and mining properties and in their valuation. Physical Influences PRIMARY limitations on the rate of mining are the rate of shaft sinking and underground development, the rate of hoisting, and the rate of sloping. These rates are largely determined by the physical features of a property. Technical methods which may be employed, and consequently the length of time required, are governed by the dimensions of the deposit, its attitude, depth, regularity, the unit value and character of the ore, the nature of the wall rocks, and similar factors.

Jan 1, 1938

By Bradley Stoughton

PROMINENCE has been given lately in engineering circles to the question whether an organisation with manifold interests can be as effective as one with a single aim, especially if that single aim be the furtherance of affairs of moment and the welfare of engineers in general. In its earlier days, the A. I. M. E. was forbidden by its constitution to engage in non-technical public affairs, but the members altered the constitution in this respect, in the year 1912, in response to the growing demand that engineers be more human in their interests and that the engineering societies represent them in this respect. Since that time, the activity of mining engineers in public affairs has been growing rapidly, and we are happy that the Institute has been able to render very valuable economic services. Doubtless the greatest public service rendered by engineers in a recent great emergency was the work of the Naval Consulting Board, without which the U. S. Navy would never have been able to enter promptly into service upon our entrance into the war, ,and both Navy and Army would have been a long time without the munitions that came at an early date. We can never forget that this Board was established through the direct activity of the then President of the A. I. M. E., with the hearty cooperation of other national organizations.

Jan 1, 1920

By Alfred Weiss

Over the past 25 years hard-rock mining companies have developed a number of profitable computer applications which appear applicable to operations in the coal industry. The evolution of these applications are described and the most profitable discussed. The basic nature of these systems is that they must cut across organizational boundaries. While technological advances contributed significantly to the successful implementation of computers within mining, the human aspects related to organization, management and control of systems projects remain as key to future success in coal as they were and still are in hard-rock mining.

Jan 1, 1983