Search Documents

By J. P. Newell, R. W. Storey

This paper describes the development of a continuous float-and-sink process to produce coal low enough in ash content to be suitable for production of electrodes. The cleaned coal had a combined iron and silicon content of 0.239 pct. The efficiency of recovery was 84 pct. AUGER mining is a form of continuous mining in that it completely replaces with a one-cycle operation the older conventional cut, drill, shoot, and load method of mining. Relatively new, having been utilized only within the last few years, it is even more continuous in its production of coal than some other forms of continuous mining being practiced in this country today. There are at present coal recovery augers in operation working along strip-mined highwalls from the outside. This paper will deal with underground mining, specifically with an experiment which was carried out with a machine developed for this purpose. The location of this experiment was in Pike County in eastern Kentucky in the upper split of the No. 3 Elkhorn seam. Coal height was 32 in. and roof conditions were very bad, with 10 in. of soft draw slate coming down with every cut in conventional mining. The coal is high-grade bituminous, excellent for metallurgical coking. Underground auger mining fills a need for a method of recovering coal in thin seams, under bad roof conditions or in split seams. In many cases it might save money by eliminating the handling of excessive quantities of rock. In fact, if the coal can be recovered, as in the case of this experiment, without mixing with any impurities outside the seam, it may be possible to load or ship a satisfactory product with little or no preparation or cleaning expense. The need for some economical method for recovering coal from thin seams is becoming more pressing as the more profitably mined seams are exhausted. Basic Principles of Auger Mining The principles of the auger, or screw conveyor, have long been used in drilling small diameter holes for blasting and other purposes. These same fundamentals apply to large diameter drilling. However, considerably more attention was given to designing a cutting head that would not pulverize the coal and consequently would require a minimum of power to drive it. The head, as designed for this job, consists of a cylinder 25 in. in diam with steel bits set in 3 positions spaced around the forward rim. A conventional coal drill bit, at the head of a bursting cone in the center of the cylinder, trails the forward rim slightly, see Fig. 1. The bursting cone and auger connections are anchored to the cutter barrel by 3 arms spaced at 120". This head design proved to be very satis-

Jan 1, 1953

By E. E. McGinley, L. D. Woodworth

During the past several years has occurred what, in the light of future events, may aptly be called the rebirth of the acid Bessemer process. The increased attention given to the technical and metallurgical details involved in the production of Bessemer steels has been exceedingly fruitful, and indicates the value of further research and p1ant development. In times like these, when the steelmaking capacity of the country is operating at a maximum rate to supply materials for the national defense program, it behooves the Bessemer operator not only to strive to increase production but also to maintain a high standard of quality. The opportunity is ripe, it seems, to recapture fields of application once considered the birthright of Bessemer steels, but supplanted in recent years by open-hearth grades. This involves cooperation all along the line, from the blast-furnace operator to the metallurgical contact man and salesman. The metallurgist's part in this program involves the study of the many steelmaking variables and the measures necessary to ensure constancy in the finished product. It is equally important that the knowledge gained be disseminated widely to ensure the wise application of Bessemer steels in new fields. The merits of Bessemer steels for certain work are well understood. The combined properties of good weldability, machinabil-ity and stiffness are unique and fully explain the strong entrenchment of Bessemer steels in certain fields; e.g., skelp for small butt-weld conduit, screw steels machined in automatics, and certain tin-plate applications. It is the purpose of this paper to review briefly the physical properties of Bessemer steels as contrasted with those of open-hearth steels, to discuss control measures now employed in the making of Bessemer steel, and to consider the advantages derived from the use of these control measures. Physical Properties oF Bessemer vs. Open-hearth Steels A number of Bessemer blows and open-hearth heats were tested for tensile strength, ductility and impact strength. The steels selected were confined to sections from 3/4 to 1 1/4-in. diameter, inclusive, and the carbon content covered was sufficient to yield parallel ranges in ultimate strength for the comparison. Other factors, such as the extent of deoxidation of the steel and variations in chemistry, were kept as comparable as possible. Machined test pieces of 0.505-in. diameter with an 8-in. gauge length were pulled. The data obtained are shown in Fig. I, ultimate strength being plotted against carbon content. This graph shows that for equivalent carbon content Bessemer steel has on the average 15,000 lb. per sq. in. greater tensile strength and, conversely, for the same tensile strength Bessemer steel requires on the average 0.14 per cent less carbon. The average phosphorus content for the Bessemer steel was 0.090 per cent,

Jan 1, 1941

By R. Floyd Farris

Al thorough knowledge of the behavior of cement slurries under elevated temperatures and pressures is necessary in order to solve properly the many problems presented in deep-well cementing operations. In the earlier days of the petroleum industry the depths of wells were shallow as compared to those of today, and the subsurface temperatures and pressures were not of sufficient magnitude to affect seriously the problem of proper control of cement-slurry properties. Today, however, the search for new reserves has extended drilling to such depths that bottom-hole temperatures of more than 200°F. and bottom-hole pressures of 3000 to 5000 lb. are not uncommon. Moreover, there is every indication that within the next few years wells will be drilled to even greater depths and bottom-hole temperatures and pressures will be correspondingly higher than those with which we are concerned today. It has been realized for some time that the behavior of cement slurries at high temperatures and pressures might be very different from that at atmospheric tempera-ture-pressure conditions, but while the temperature effects have been investigated with a reasonable degree of thoroughness, the pressure effects have received little public attention. While the trend toward deeper drilling may make changes in cementing technique and the choice of cements imperative, it was the purpose of this investigation to consider factors having a bearing on the latter, only secondary consideration being ,given, for the present, to details of tech-nique and equipment for oil-field use. More specfically, the purpose of this work was to consider the effect of temperature and pressure upon the behavior of cement slurries. Although it has long been recognized that cements thicken and set rapidly with increasing temperatures, practical methods for the quantitative determination of these effects are comparatively recent developments. In 1935 Silcox and Rule1 presented such a method, describing apparatus designed to measure the consistency-time relationship of cement slurries at relatively high temperatures. The practical importance of this apparatus in furnishing useful data for the evaluation of cement slurries for cementing operations has been emphasized in various technical publications by such writers as E. L. Davis,~ I. F. Bing-ham,3 and J. E. Weiler.4 A paper describing the numerous tests now used to evaluate cements for oil wells was presented in 1939 by W. W. Robinson.= Robinson describes the Consistometer and the Thickening-Time Tester, showing similarity of data from the two devices, and points out that the purpose of each apparatus is to determine the allowable time that a cement may be pumped at a given temperature. At the present time, however, it is believed that results from the Thickening-Time Tester and the Consistometer have not given a

Jan 1, 1941

By R. Floyd Farris

Al thorough knowledge of the behavior of cement slurries under elevated temperatures and pressures is necessary in order to solve properly the many problems presented in deep-well cementing operations. In the earlier days of the petroleum industry the depths of wells were shallow as compared to those of today, and the subsurface temperatures and pressures were not of sufficient magnitude to affect seriously the problem of proper control of cement-slurry properties. Today, however, the search for new reserves has extended drilling to such depths that bottom-hole temperatures of more than 200°F. and bottom-hole pressures of 3000 to 5000 lb. are not uncommon. Moreover, there is every indication that within the next few years wells will be drilled to even greater depths and bottom-hole temperatures and pressures will be correspondingly higher than those with which we are concerned today. It has been realized for some time that the behavior of cement slurries at high temperatures and pressures might be very different from that at atmospheric tempera-ture-pressure conditions, but while the temperature effects have been investigated with a reasonable degree of thoroughness, the pressure effects have received little public attention. While the trend toward deeper drilling may make changes in cementing technique and the choice of cements imperative, it was the purpose of this investigation to consider factors having a bearing on the latter, only secondary consideration being ,given, for the present, to details of tech-nique and equipment for oil-field use. More specfically, the purpose of this work was to consider the effect of temperature and pressure upon the behavior of cement slurries. Although it has long been recognized that cements thicken and set rapidly with increasing temperatures, practical methods for the quantitative determination of these effects are comparatively recent developments. In 1935 Silcox and Rule1 presented such a method, describing apparatus designed to measure the consistency-time relationship of cement slurries at relatively high temperatures. The practical importance of this apparatus in furnishing useful data for the evaluation of cement slurries for cementing operations has been emphasized in various technical publications by such writers as E. L. Davis,~ I. F. Bing-ham,3 and J. E. Weiler.4 A paper describing the numerous tests now used to evaluate cements for oil wells was presented in 1939 by W. W. Robinson.= Robinson describes the Consistometer and the Thickening-Time Tester, showing similarity of data from the two devices, and points out that the purpose of each apparatus is to determine the allowable time that a cement may be pumped at a given temperature. At the present time, however, it is believed that results from the Thickening-Time Tester and the Consistometer have not given a

Jan 1, 1941

By A. Madrazo

The Standing-Katz method for predicting liquid densities of reservoir fluids has been tested using experimental data of 154 bottom-hole or recombined reservoir fluid samples. New pressure- and temperature-correction curves for the Standing-Katz type correlation are presented which improve the accuracy of prediction. INTRODUCTION The present study was undertaken to investigate the known methods of determining liquid densities and to select one of them which might yield a better correlation if additional data were employed. An appropriate correlation would incorporate the following characteristics: (1) ease of handling in the computations, (2) results within engineering accuracy and (3) data easily accessible. After careful investigation of the different methods, the Standing-Katz correlation1 appeared to have these characteristics. The Standing-Katz correlation for liquid densities of hydrocarbon systems is based upon limited data. The original work, which employs apparent densities for methane and ethane, was based on data of 15 saturated crude oils in equilibrium with natural gas. Therefore, a test of the correlation using additional experimental data would serve either to validate the Standing-Katz correlation or to form a basis for corrections if such were necessary. PROCEDURE AND GRAPHICAL SOLUTION The data of 154 bottom-hole or recombined reservoir fluid samples were employed to calculate the densities at 14.7 psia and 60°F by the method described in Table 1. Volume contributions for methane and ethane were assigned from the pseudo liquid density plot (Fig. I), but volume contributions for N2, CO2 and HzS were not considered. The densities computed at reference conditions of 14.7 psia and 60°F were then elevated to their respective temperatures and pressures by the use of the correction curves proposed by Standing.' The percentage differences between the experimental values and the calculated values were determined; these samples were grouped into temperature, pressure and density ranges to determine a possible trend. It appeared that, at temperatures above 160°F, the calculated density values were consistently larger than the experimental density values; however, no obvious trend was found for the density and pressure ranges. There is a relationship between the pressure-correction and temperature-correction curves. This relationship, embodied in the temperature-correction curve, can be expressed as follows. The experimental densities of 125 samples above their bubble points were known. From these isothermal data, it was possible to determine an experimental-density difference between two pressures; and (from Fig. 2*), a calculated density difference between the same two pressures was determined. The relative effect of temperature must be considered in the calculated-density values. The effect of temperature can be determined by entering Fig. 3* at the two densities in consideration and obtaining the change in density at constant temperature. This change, or delta density, must be added

By Jack A. Crichton, Henry J. Gruy

This paper discusses methods used in the estimation of natural gas reserves and the general conditions under which the various methods are applicable. The factors used in estimating natural gas reserves are reviewed. Errors which have been found to occur frequently are listed. Introduction The estimation of natural gas reserves has become of paramount interest because of the increasing importance of gas in the nation's economy. Gas is a most desirable fuel, a fact substantiated by the continued rise in the market demand. In addition, new uses for gas are being developed by the chemical, plastic, and associated industries, and plants are being built to make gasoline from natural gas. These are a few of the factors contributing to the importance of the nation's natural gas reserves. With the increased importance of gas there is an increase in the need for reliable estimates of the magnitude and availability of natural gas reserves. These estimates are being used currently: (I) to determine which fields contain sufficient available reserves to justify the construction of pipe-line outlets to serve particular markets; (2) to design pipe lines necessary to serve those fields adequately;] (3) to determine the location of industrial and chemical plants; (4) to finance the development of gas properties, and the construction of gas pipe lines; (5) to determine fair and adequate depletion allowances and depreciation rates; (6) to justify applications for gas pipe lines before various regulatory bodies; (7) to determine the number of wells required to exploit the reserves most economically; (8) to aid in establishing values for the purchase or sale of gas properties, and for purposes of inheritance taxes; (9) to determine equities under unitized operations; (10) to provide a basis for calculating the economics of gas-cycling operations. History or Estimation of Natural Gas Reserves The natural gas industry in the United States had its beginning during 1826 when natural gas was used for lighting the city of Fredonia, N. Y. The first natural gas pipe line was a 25-mi]le wooden line constructed from hollowed logs, connecting West Bloomfield and Rochester, N. Y. There is no record of an attempt to estimate the gas reserve at West Bloomfield but an attempt was made to determine the capacity of the well by measuring the time required to 611 a large balloon. One of the earlier publications concerning estimation of natural gas reserves is the "Manual for the Oil and Gas Industry," published by the Treasury Department, United States Internal Revenue, in i9i9. The following methods of computing "gas depletion" are listed: (I) production decline of the gas well or property; (2) decline in open-flow capacity; (3) comparison with the life history of similar wells or properties, particularly those exhausted Art

Jan 1, 1949

By R. D. Lee

A simplification of the method of Hurst and McCarty for conducting potentiometric model studies by the single probe method is presented along with experimentally determined invasion patterns for certain idealized flow problems. The analytical solution for one class of these problems is given. Finally, a general description is given of a newly developed instrument which permits direct mapping of flow lines and determination of transit times in potentiometric-model studies. Introduction The object of this paper is to present: I. A simplification of the method of Hurst and McCarty for conducting poten-tiometric-model studies of oil and gas reservoirs by the single probe method. 2. Results of a series of studies of certain idealized flow problems and the general conclusions to be drawn therefrom. 3. A description of a new instrument, the Chronocartograph, which greatly reduces the labor and time required for conducting potentiometric-model studies. Certain general conclusions may be drawn as results of the investigation of the idealized flow problems. They are: I. Injection and extraction areas should be separated by as great a distance as conditions permit since, in general, the recovery prior to first breakthrough tends to vary as the square of this distance. 2. Little advantage is to be gained by use of more than eight injection wells or groups of injection wells for the case of circular productive limits. 3. Elongated shapes of productive limits are best exploited by injection on the extended major axis only, with a line of extraction wells lying on the major axis. 4. The use of peripheral injection wells for elongated shapes is permissible, if necessary, but requires extension of the line of extraction wells. The exploitation of an oil or gas field is effected either by the expansion of the gas and oil, or by their displacement by another fluid. Both methods may be used simultaneously. When the displacement of the oil or gas is the controlling factor there arises the problem of mapping the progress of the boundary between the fluid in place and the displacing fluid. This problem is of particular interest in the operation of a cycling project in a gas-condensate field, where the wet gas is produced from one or more wells, commonly called "extraction wells.'' This wet gas is taken into a processing plant where the condensate is removed. The remaining "dry" gas is injected back into the field through one or more wells, called "injection wells," both to conserve the gas for future use and also to maintain the pressure in the field. In an operation of this type it is essential to anticipate the manner in which the dry gas will spread through the field, because the ultimate recovery of the wet gas depends

Jan 1, 1948

By R. D. Lee

A simplification of the method of Hurst and McCarty for conducting potentiometric model studies by the single probe method is presented along with experimentally determined invasion patterns for certain idealized flow problems. The analytical solution for one class of these problems is given. Finally, a general description is given of a newly developed instrument which permits direct mapping of flow lines and determination of transit times in potentiometric-model studies. Introduction The object of this paper is to present: I. A simplification of the method of Hurst and McCarty for conducting poten-tiometric-model studies of oil and gas reservoirs by the single probe method. 2. Results of a series of studies of certain idealized flow problems and the general conclusions to be drawn therefrom. 3. A description of a new instrument, the Chronocartograph, which greatly reduces the labor and time required for conducting potentiometric-model studies. Certain general conclusions may be drawn as results of the investigation of the idealized flow problems. They are: I. Injection and extraction areas should be separated by as great a distance as conditions permit since, in general, the recovery prior to first breakthrough tends to vary as the square of this distance. 2. Little advantage is to be gained by use of more than eight injection wells or groups of injection wells for the case of circular productive limits. 3. Elongated shapes of productive limits are best exploited by injection on the extended major axis only, with a line of extraction wells lying on the major axis. 4. The use of peripheral injection wells for elongated shapes is permissible, if necessary, but requires extension of the line of extraction wells. The exploitation of an oil or gas field is effected either by the expansion of the gas and oil, or by their displacement by another fluid. Both methods may be used simultaneously. When the displacement of the oil or gas is the controlling factor there arises the problem of mapping the progress of the boundary between the fluid in place and the displacing fluid. This problem is of particular interest in the operation of a cycling project in a gas-condensate field, where the wet gas is produced from one or more wells, commonly called "extraction wells.'' This wet gas is taken into a processing plant where the condensate is removed. The remaining "dry" gas is injected back into the field through one or more wells, called "injection wells," both to conserve the gas for future use and also to maintain the pressure in the field. In an operation of this type it is essential to anticipate the manner in which the dry gas will spread through the field, because the ultimate recovery of the wet gas depends

Jan 1, 1948

By Paul Weaver

DURING 1932 the amount of geophysical surveying carried out as a part of oil-field development in¬creased, particularly in the Gulf Coast of Texas and Louisiana. Here the most intensive geophysical activity was displayed in the discovery of domes and prospects several years ago, after which there was a period of relative inactivity. This year many of the leases required development and geophysical methods were used to obtain pictures of the detailed structures. These were almost exclusively gravity and reflection-seismograph surveys and for the first time this latter method was generally used by oil operators to construct subsurface contours. The total number of geophysical troops in this territory increased from 16 to 40 during the year.

Jan 1, 1933

By J. F. Ednie

SCRAP metals to the value of more than a billion and a half dollars were recovered in the United States in 1939 for further use in industry. Few people have any true conception of the magnitude of the secondary-metal industry as related to that engaged in the production of the primary, or virgin, metals; of its importance, particularly when a shortage of primary metals exists, as at present; or of the advance that has been made in standardizing and improving the quality of its products. Of the iron and steel produced in the United States in 1939 (the data used in this article are largely taken from Bureau of Mines reports for that year) just over 50 per cent came from scrap and slightly less than 50 per cent from ore. Of the principal nonferrous metals-aluminum, anti-mony, copper, lead, nickel, tin, and zinc-63 per cent came from domestic ores and 37 per cent from scrap. Fig. 1 presents graphically the relative tonnage and value of primary and secondary production of ferrous and nonferrous metals. In this chart only purchased secondary metals are considered, the figures being exclusive of "home" or "plant" scrap which amounts to rather large figures in the iron and steel industry. Incidentally, the chart shows that from the tonnage standpoint the iron and steel industry is some twenty times larger than the nonferrous industry, though with regard to the value of the product the ratio drops to about two to one.

Jan 1, 1941

By Earl Oliver

SEVERAL notable papers, and free discussion on many controversial subjects, marked the various sessions of the Petroleum Division at the annual meeting. The Division first convened on Tuesday afternoon, Feb. 16, and wound up with a dinner and technical meeting on Thursday night. H. C. Fowler presided at the opening session, which was devoted to problems of engineering research and production engineering. Joseph Chalmers abstracted his paper on the flow of air and gas through porous media, in the preparation of which E. L Rawlins and D. B. Talia-ferro contributed. G. H. Fancher told how much he and his associates at Pennsylvania State College were interested in this field, and described the problems they had met in conducting test work. He made a plea for standardization of testing methods. Mr. Fowler then read an abstract of written discussion by Professor Barb, which was followed by discussion by Dr. Fancher and Mr. Chalmers of technical points in connection with the Chalmers' paper. H. H. Hill abstracted written discussion from Messrs. Wilde and Moore, of the Humble company. The second paper, by K. B. Nowels, on computing pressure drop in the pipe of flowing oil wells, was abstracted by the author. Messrs. Blair Smith, G. W. Coggeshall, and I. I. Gardescu participated in the discussion, and the chairman abstracted written discussion prepared by Mr. Rawlins. Most of this had to do with the viscosity of gas¬oil mixtures, on which subject Mr. Nowels said there was great need of accurate technical information.

Jan 1, 1932

John Birkinbine, Philadelphia, Pa.: We have in the Institute two Dudleys—Dr. Charles B. Dudley, who has so thoroughly studied the chemical composition and physical behavior of rail-steel, and Dr. P. H. Dudley, whose investigations and

Jan 1, 1900

By AIME AIME

DESPITE the fact that its membership is spread over every continent of the globe, the Petroleum Division was able to report a very substantial attendance at its meetings. Careful planning on the part of its chairman, J. B. Urnpleby, and his associates resulted in the presentation of a program that was of timely interest -and led to discussions that will unquestionably prove to be of major value to the petroleum engineer and to the oil industry in general. Scheduling of meetings so as to avoid all conflicts made it possible to obtain a higher average attendance at the several sessions* than in previous years, and gave everyone a chance to hear all of the papers that he was interested in. The chairmen of the various meetings are to be congratulated especially for their skill in handling them so that at .no time was there the least indication of lagging interest.

Jan 1, 1930

[University of Alaska College, Alaska Mining Society TOM CHRISTENSON, President MARY ANN KISER, Secretary H. G. WILCOX, Faculty Sponsor WM. FACKLER, Counselor University of California Berkeley, California Mining Association JOHN W. COOK, President LORETTA A. RICHTER, Secretary W. S. WEEKS, Faculty Sponsor]

Jan 1, 1946

By S. WHINERP

(Cleveland Meeting, October, 1912.) I AM indebted to L. E. Bryant, of Danville, Ky., President of the Virginia Mining Co., operating coal-mines in Scott county, Tenn., for the following information relating to the existence of the Clinton iron-ore under the NW. slope of the Cumberland Plateau in Kentucky and Tennessee. During the past 15 years quite an important oil-field has been developed in a region having Wayne county, Ky., as its center, and a large number of wells have been drilled in that and adjacent territory in the search for oil. Many of' these wells have been carried to considerable depths below the recognized oil-bearing horizon, and one of them was drilled by Mr. Bryant at Pine Knot, a station on the Cincinnati, New Orleans & Texas Pacific railroad, a few miles north of the point where that road crosses the Kentucky-Tennessee State-line. The elevation of the surface at the crossing is about 1,400 ft. above sea-level. The railroad is located on the dividing ridge between the Cumberland river and Big South Fork. At a depth of 1,720 ft. below the surface the drill reached and passed through a formation which the drillers called " red rock," but which Mr. Bryant classified as Clinton iron-ore, as its geological position corresponded to that formation. The ore at this point was 6 ft. thick and appeared to be of uniform quality throughout. An analysis of the drillings gave : Fe, 33; Mn, 0.25; Si02? 3 ; Al203, 2 ; CaO, 13; MgO, 7 ; P,05, 0.333 per cent. ; S, trace. This analysis seems to confirm the belief that the ore is Clinton, and that it is of a quality equal to the average of the deep or unbleached Clinton ores in Tennessee and Alabama. This discovery led Mr. Bryant to make further examinations and inquiries, and he found that the stratum called " red rock " by the drillers had been passed through and noted in the great majority of the wells carried down to the same geological hori-

Oct 1, 1912

By Arthur Connolly

WHEN scientific literature was lacking or meager, research necessarily meant laboratory investigation above all else. Today, scientific literature has attained tremendous proportions, and the volume increases at a much faster rate than it is digested and efficiently utilized. For that reason the present-day research worker should spend much more time in the library, and correspondingly less in the laboratory, than is the general custom. Library research would overcome two serious errors often made by scientists: duplication of work described completely and failure to appreciate inventions described almost verbatim in the literature. To emphasize these failings that often occur in present-day research, consider a hypothetical scientist as he conducts his search from inception to the stage where it is made available to the public by patent or other publication.

Jan 1, 1942

By Ta M. Li

Expanded mine-mill capacity and greater operating flexibility are part of the dramatic changes taking place in the Tennessee mining operations of Asarco, Inc. Climaxed by the recent start-up of the $6.3 million Young mill in September 1975, Asarco has pushed Tennessee back into number one position as the leading zinc mining state. Furthermore, start-up of the Young mill is expected to insure a much-needed and continuing domestic zinc supply, at a time when US mines can only supply one-half of 1975 domestic consumption.

Jan 5, 1976

By L. D. Jaffe, D. C. Buffum, F. L. Carr, M. Goldman

IN an earlier investigation by Jaffe and Buffum,' a time-temperature transformation diagram for isothermal temper embrittlement of an SAE 3140 steel showed some suggestion of two overlapping "noses." These authors mentioned, as a possible explanation, that their specimens embrittled at 525°C were slightly softer than expected, perhaps because of some slight unknown variation in tempering treatment. Because a double nose would be of considerable importance in elucidating the mechanism of the temper brittleness reaction,' it appeared worthwhile to redetermine the portion of the diagram near 525°C. The same heat of SAE 3140 steel was used as in the previous work, and experimental procedures were the same.' Blanks were austenitized 1 hr at 900°C, water-quenched, tempered 1 hr at 675°C, and water-quenched. Groups were then embrittled isothermally at the temperatures and for the times shown in Table I, and water-quenched. For comparison, one series was tempered various times at 675°C, water-quenched, and given no further treatment. V-notched Charpy impact specimens machined from the blanks were tested over a range of temperatures. Energy absorption and percentage of fibrous fracture were plotted vs test temperature for each group, utilizing both the new data and those for the same treatment obtained in the earlier work,' except that the earlier data at 525°C were discarded.* are given in Table I. After a small correction (-0.28°C/BHN) for the variation of hardness" from Rockwell C24, the transition temperatures were plotted against embrittling time for each embrittling temperature, using the data of Table I for the range of treatments covered there, and using previous dataL for other treatments. By cross-plotting, Fig. 1 was finally obtained. It appears from this figure that if there are two noses to the time-temperature-transformation diagram for isothermal temper embrittlement of SAE 3140 steel, the upper nose must lie above 575°C. As interest had been primarily in the region near 525°C, a thorough study of embrittlement above 575°C was not made. Fig. 1 shows that such a study is needed, especially since preliminary measurements at the tempering temperature of 675°C reveal much more rapid embrittlement than would be expected from the data at lower temperatures. The transition temperature increased, approximately, as the logarithm of the tempering time (about 81/2°C, after correction for hardness, for each doubling of the time).& Since three tensile specimens tempered 240 hr at 675°C and water-quenched had an average yield-tensile ratio of 0.844, with 70.7 pct reduction of area, it is assumed1 that the tempering temperature is not above Ae1. The omission of a quench-and-reheat operation below Ae1, for the groups tempered at 675°C, as compared to groups embrittled at lower temperatures, should not affect results." More detailed investigation of embrittlement above 575°C is now under way.

Jan 1, 1954

By Ednlund D. North

Discussion of the paper of Edmund D. North, presented at the Spokane meeting, September, 1909, and published in Bulletin No. 37, January, 1910, pp. 21 to 25. A. SCOTT REID, London, Eng. (communication to the Secretary*) :-As a constructor of several glass mine-models, I have read with much interest the description of the model of the Montana-Tonopah mine-workings by Edmund D. North. As an interchange of ideas and experience is always an advantage, and in view of the fact that such models are coming more and more into vogue, perhaps the following remarks on this subject may prove of interest to mining engineers generally and to Mr. North particularly. In the model of the Waihi gold-mine, New Zealand, which I constructed, a dust-proof case is used. The top, bottom, front, and two ends are of glass; the back only is of wood, painted a dull white, against which the mine-workings show very distinctly. Each mine-level is represented by a horizontal sheet of glass, supported on metal runners fixed to the uprights at each end of the case, in a manner similar to that described by Mr. North. The corner uprights are strengthened by having a metal band screwed to the inside face of each, to which the metal runners or supports for the sheets of glass are screwed in turn. The reason for having this additional strength is that as the mine is developed in depth, and fresh levels are opened, the increasing weight of the glass sheets, added to the model, caused the unsupported wooden uprights to bend slightly, so that the glass sheets-did not fit in with the desired nicety, and co-ordination was, to a considerable extent, lost. Strengthening the uprights in this manner is not important in models of mines in which only a few levels have been opened, or when the sheets of glass are small, but in the Waihi model there are 15 sheets of glass to be supported, and more to be added as development proceeds, and the weight is considerable.

May 1, 1910

By Robert W. Hunt

The first pump of this character, made by H. R. Worthington, and, so far as the writer is informed, the first and only one of this kind ever constructed, is now in daily use in the above-named works. The water-pressure necessary for the working of the hydraulic machinery of this plant had been supplied, up to the time of the building of this pump, by two Worthington Duplex High Pressure Pumps, having steam-cylinders of 20 inches diameter and 12-inch stroke, with water-plungers of 71/2 inches diameter; eight inlet and eight outlet valves of 24 inches diameter, and pumping into a 6-inch pipe. These pumps required a large amount of steam, and, in consequence of the various additions to their duty, their capacity became far short of the work required. In preference to putting in another engine of the same class, it was decided to accept Mr. Worthington's proposition to build the compound one under description, he guaranteeing that it should be equal to the demands of the works, and at the same time cause a saving of from 5 to 6 tons of coal per day from the amount required to run the two old pumps. The new engine has been in operation about one month, and so far has exceeded the most sanguine expectations. It consists of two high-pressure cylinders of 21 inches and two low-pressure ones of 363/8 inches diameter, by 36-inch stroke, with water-plungers of 961/2 inches diameter. There are two air-pumps of 20 inches diameter by 18-inch stroke; the condenser being 24 inches diameter by 60 inches high. Both cylinders are jacketed with wood and felt, and the low-pressure cylinder also with live steam. The high and low pressure steamcylinders are in line and immediately adjoining each other, while the inconveniences attending an internal stuffing-box are avoided by having two piston-rods for each of the low-pressure cylinders, running through stuffing-boxes on the outside of the smaller high-pressure ones. The steam-valves are very ingeniously designed balanced