Search Documents

By George Ross Green

[In discussion of the paper of Mr. J. C. Bayles, read at the New York meeting of September, 1890, Trans., xix., p. 18.1 It is often so difficult to locate the causes of failures of machinery and apparatus which can be examined and studied at leisure, that it is not surprising that the causes of explosions should escape detection. Usually the explosion is the first evidence that anything is amiss, and the time for observing the conditions is necessarily brief. An incident in a welding-works near Essen, Germany, might be cited as exemplifying what trifling causes may lead to disaster, and how difficult, under the most favorable conditions, it may be to discover them. A blowing-engine was arranged with two suction-pipes at each end of the blowing-cylinder—one leading to the air, and the other to the gas-holder. Each pipe was provided with a valve, and all were so adjusted that the cylinder drew in gas and air in the proportions found most advantageous. The gases from the cylinder were carried directly to the furnace through suitable pipes, and while the cylinder was provided with relief-valves, every effort was made to prevent explosions, principally by compressing the gases to a point where the rate of efflux of the mixture was greater than the velocity of combustion, if the expression is here allowable. It was found that the apparatus would work satisfactorily for some time, and then the relative proportions of the mixture would change, and an explosion might have been the result. Experiments consuming days were made to discover a method of averting this danger, but they were unsuccessful, until it was observed that the change in the composition of the mixture of gas and air took place when the gasometer began to rise or fall—the back-pressure due to friction when the holder was rising or its absence when falling being sufficient to change the conditions. As soon as this was discovered,

Jan 1, 1892

By Ralph Hultgren, Haim H. Chiswik

In recent years considerable attention has been devoted to the development of new commercial uses for silver, chiefly because of lowered prices and large stocks of the metal. This has led to increased interest in the phase diagrams of silver alloys. The silver-lead diagram is reported' to be of the simple eutectie type, but no measurements of the solubility of lead in silver have been made. The solubility of silver in lead has been estimated2 from diffusion experiments and resistance measurements to vary with temperature from 0.09 to 0.18 atomic per cent (0.05 to 0.10 weight per cent). Silver-rich silver-lead alloys have recently been recommended as high-strength bearing metals3 The silver-bismuth diagram is similar.' The solubility of bismuth in silver. has been estimated to be about 5.5 weight per cent on the basis of X-ray work.4 Matthiessen6 found a solubility of silver in bismuth from 0.25 to 0.50 per cent by conductivity measurements. Silver and thallium form the same type of diagram,' with no data on their mutual miscibilities. We have studied the first two of these diagrams by X-ray methods, verifying their main features and determining the solubilities of lead and bismuth in silver at several temperatures. We also determined the solubility of thallium in silver at one temperature. The solubilities of silver in lead and in bismuth were found to be too low to be detectable. Materials and Methods Mallinckrodt precipitated silver, analytical reagent, was used. Maximum impurities listed on the label were: chloride, 0.005 per cent; copper, 0.001; iron, 0.002; other heavy metals (as Pb), 0.002; and sulphate (SO³), 0.05. The lattice constant was found to be a0 = 4.0782 $., in good agreement with the value of Jette and Foote,6 a0 = 4.0779 A., for

Jan 1, 1940

By D. M. Podobnik, J. F. Shirley

The Cuajone Concentrator of the Southern Peru Copper Corp. is located approximately 900 km southeast of Lima, Peru, near the 500 year old town of Moquegua, in an area that has been occupied since antiquity since the plant was started in July, 1976, the throughput has steadily increased from 36 to 46 kt/d (50,7055tpd). The widely distributed molybdenite content of the ore body ranges from 0.02-0.4% MoS2. The molybdenite content of the copper concentrate has always been sufficient to justify operation of a byproduct molybdenite plant. During the first nine months of 1980, the average grade of the ore was 1.169% copper and 0.026% molybdenite. Pilot plant testing conducted during 1970 at Toquepala, Cuajone's sister plant, determined that the recovery of the molybdenite into a salable concentrate could be accomplished relatively easily by using the Asmol process. Experience gained at Toquepala, which converted to Asmol in 1969, confirmed the simplicity of process. Simplicity of operation was one of the major criteria for the process selection because, at the time, it was expected that the molybdenite plant would start up concurrently with the copper concentrator. Other processes studied either produced inferior results or were judged more difficult to operate. However, geological information indicated that the molybdenite content of the ore would be relatively low for the first couple of years of operation, so the design and construction of the plant was delayed until after the copper plant was in production. Asmol remained the process selection. During 1976 and 1977, the flowsheet and plant layout based on pilot plant data, new results obtained from Cuajone's metallurgical laboratory, and process improvements from Toquepala's experience were completed. One of the more important innovations from the Cuajone laboratory was that the Asmol consumption could be substantially reduced by replacing air with nitrogen gas in the rougher and first cleaner flotation steps

Jan 1, 1983

By Charles Legrand

The power plant of the Burro Mountain Copper Co. is located near Tyrone, N. M., at 5,950 ft. elevation. It is interesting because it uses the largest stationary Diesel engines in the United States. The general layout of the plant is shown in Figs. 1 and 2. The building is of steel-frame construction with hollow-tile walls and corrugated-iron roof; the floor is concrete and all windows have steel frames, making a fireproof building. The building is made to accommodate one more electric generator unit which is being installed; also two 4,000-cu. ft. air compressors direct-connected to three-cylinder engines with the same size cylinders as the electric units. The power plant consists of two 815-kva., 60-cycle, three-phase, 6,600-volt, 180-r.p.m. generators, direct-connected to five-cylinder, two-cycle Diesel engines; the necessary circulating pumps for cooling water, cooling towers and oil storage tanks. A portion of the power is used in the same building as the generating units to run one of two 200-kw. rotary converters delivering 260-volt direct current, and a 2,500-cu. ft. air compressor, delivering air at 95 lb. pressure, direct-connected to a 400-hp., 6,600-volt, three-phase synchronous motor. The remainder of the power is used to run a 1,500-ton concentrating mill 3 ½ miles from the power house, various hoists, pumps and motors about the mines and the lighting and water-works of the town of Tyrone. The direct current is used for electric traction in the mine, also to run hoists and motors that were installed before the new power plant was built. Due to the large hoists that take starting peaks of 250 kw. and the 10-ton electric locomotive that takes at times 150 kw., the load is extremely variable, as shown in. Fig. 3.

Jan 9, 1916

By Ralph Sweetser

PROGRESS in blast-furnace practice during 1922 has been in the direction pointed out in my article in the March, 1922, issue of MINING AND METAL-LURGY; this advance has been very satisfactory in spite of the difficulties caused by the great coal strike and the railroad strike. The progress, especially in increased tonnage, has been brought about, not by increasing the size of the furnaces, not by improved mechanical devices, but through the application of better blast-furnace practice; the advance has been metallurgical rather than mechanical. The increase in production per stack, has been more pronounced than in any period since the time that James Gayley began to break blast-furnace records in Pittsburgh. These big tonnages have been made in furnaces designed to make 550 to 600 tons of pig iron per day; but several such furnaces have had monthly averages of between 700 and 800 tons per day with a corresponding reduction of cost, and a reduction in the number of man-hours of labor per ton of pig iron. During this period there has been a wider acceptance of the fact that satisfactory blast-furnace results are more dependent on coke quality than on any other factor. There has always been much rivalry among blast-furnace men in making new tonnage records, and many schemes have been used for getting out big pro-duction, but the blast-furnace man cannot make the high records all by himself; it is necessary for him to have the cooperation of the entire management, and also the help of the organization that makes his blast-furnace coke. Herman Brassert has said that "there is no blast-furnace practice possible that can wholly overcome the effects of bad coke." In the past; the blast-furnace superintendent has often been under suspicion if he complained about the quality of the coke in times of unsatisfactory blast-furnace results, but it is now conceded that if the quality of the coke is not right, complaints are not necessarily made as an alibi.

Jan 5, 1923

By Thomas A. Wright

No symposium on die-casting could be complete without consideration of the methods of formula and impurity control. No corisideration of control would be complete without discussion of that new tool of the analytical chemist and inspector, the quartz spectrograph. Just as there is an increased appreciation of the possible applications of the die-casting process and of die castings, so too is there, slowly but surely, of the spectrograph. At present the role of the instrument might well be compared with that of brass or magnesium die castings. Neither is as widely understood or known as they will be. Product specifications are increasing and are getting more explicit and often more rigid. The designer, metallurgist and production engineer or superintendent will be forced to depend more and more on the chemical laboratory. Sampling, as well as analyses, testing and inspection problems will grow. The chemical laboratory must meet its increased responsibility and use of the spectrograph will become more common. Advantages of increased precision, greater speed, lessened labor and often lower costs cannot be ignored. It will be the purpose of this paper in part to outline the respective fields of chemical and spectrographic analyses and to indicate where one may overlap the other and in part to indicate certain possible sources of contamination of zinc-base die-cast alloys in particular. Composition Aluminum.-Aluminum die die castings are expected to conform to the specifications of the Amcrican Society for Testing Materialslt and the Society of Automotive Engineers2. The A.S.T.M. has recognized seven aluminum alloys in Tentative Specification B85-33-T. TWO are straight silicon and the remainder are of the copper-silicon type of which alloys VIII and IX have in addition respectively 2 and 4 per cent of nickel, but unlike the others are not covered by S.A.E. as well. All seven call for rigid control of certain impurities. With the exception of alloy XII,

Jan 1, 1935

By Earl Oliver

THE term oil property, in this discussion, includes any type of easement or grant under which petroleum might be produced; it ranges from the mere right to drill on undeveloped wildcat acreage up to a fully developed oil property. The values of an oil property, as thus defined, vary widely according to the use for which it is intended, whether it is from the viewpoint of the speculator, the fraudulent stock promoter, the refiner and pipe-line owner, or the oil producer. The market value of a property is usually a combination of some two or more of these influences, and occasionally a combination of all of them, but we prefer to treat each viewpoint as distinct from the others, allowing the reader to make his own combination in such proportions as his inclination and property seem to require. This paper will treat the subject from the viewpoint of the oil producer. However, the other influences have such bearing on the cost of property to the producer and on the price he might obtain by its sale as to warrant brief discussion of them. Speculation, particularly lease speculation, is a parasitic growth on the oil industry, healthy enough, but of no economic value. The class of property usually dealt in for this purpose is the undeveloped lease. Its speculative value may have some relation to its probable productive value, but most frequently this value is the product of temporary excitement due to local development. The lease speculator, seeking out the trend of development or securing early information regarding a proposed test or a new discovery, immediately secures leases whose market value will be increased when the existence of such development becomes more widely known. His profits are purely unearned increment. Not proposing to spend money in exploration, he can afford to compete in purchase with the operator, who, in addition to bonus paid, must spend large sums in testing out his own acreage and that of the nearby speculator as well. It has a tendency to compel unduly high bonuses.

Jan 2, 1920

By Thomas Fraser, Abreu Alvaro

THE work described in this paper was carried out under the sponsorship of the Foreign Economics Administration and in cooperation with the Departamento Nacionál da Produção Mineral, Rio de Janeiro. The project was undertaken to obtain complete data on the variations in washability of coal to be used for coke manufacture in the steel industry and to determine the economy of preliminary hand-sorting operations. The coal-producing industry of Brazil is in that pioneering stage in which operat¬ing practices and methods are just being developed. Increased wartime demand for fuel, coincident with a drastic curtailment of foreign supplies due to lack of shipping facilities, has put a tremendous pressure on the national industry to furnish more coal. Under this incentive, production facilities are being expanded and new methods of operation are being tested. Such changes are being developed both by improvement of existing methods that originated in the field and by adaptation and modification of methods introduced from the United States and Europe. These mining condi¬tions and mining practices in Brazil are typical of what the American mining engineer will find in many instances when he goes pioneering into the developing coal fields of the Southern Hemisphere. The producing coal fields of Brazil are all in the southern states of that country. The coal measures are in a band roughly paralleling the coast and extending in a generally southwesterly direction from northern São Paulo through the states of Paraná, Santa Catarina and Rio Grande do Sul to near the Uruguayan border in the vicinity of Bajé. The accompanying map1 (Fig. I shows the general location of these fields and also the principal routes of movement of both national and imported coal in a late pre-war year (1940). Statistical data on production by states up -to that year are given in Table I. Rio Grande do Sul is still the largest producer among the coal states; but wartime

Jan 1, 1946

By Michael Hoch, Daniel B. Butrymowicz

The isothermal section of the Ta-Ti-Zr-0 system at 1500°C was investigated using X-ray diffraction and rrzetallographic techniques. Up to 71.4 at, pct 0 the system contains nine four -phase regions. Zsopleths at 10, 20, 30, 40, 50, and 60 at. pct 0 were constructed. The purpose of this investigation was to determine the general shape of the quaternary equilibrium phase diagram of tantalum, titanium, zirconium, and oxygen at 1500°C. The system was truncated at 66.7 at. pct 0 on the Ti-0 and Zr-0 binaries and at 71.4 at. pct 0 on the Ta-0 binary. The Ti-Zr-0 system was investigated in this laboratory.' The binary systems of interest have been compiled and discussed by Hansen and Anderk, chmidt, Hayes, Roberson, and asche, and Hoch and athur.' EQUIPMENT The Same equipment as that for the study of the Nb(Cb)-Ti-Zr-0 system was used.' The X-ray dif- fraction patterns were analyzed with the help of the ASTM card set7 and NBS circulars.' MATERIALS The tantalum powder (99 pct pure), the titanium powder (99.6 pct pure), the tantalum pentoxide, and the zirconium dioxide used in this study were purchased from the Fairmont Chemical Co., Newark, N.J. The zirconium powder (99.4 pct pure) was obtained from the Charles Hardy Co., Inc., New York. Reagent-grade titanium dioxide was purchased from the Matheson Co., Inc., Norwood, Ohio. The oxides were dried in air at 700°C for 24 hr before use. Though the materials used were not "hyper-pure", the impurities present do not affect the results (lattice parameters, phase boundaries), within the experimental accuracy. PROCEDURE The samples were heated by induction in a vacuum furnace, and examined metallographically and by X-ray diffraction at room temperature. The procedure was the same as that in the Nb(Cb)-Ti-Zr-O work,' EXPERIMENTAL RESULTS AND DISCUSSION OF DATA A four-component system can be represented by a tetrahedron at a single temperature and pressure

Jan 1, 1964

By C. T. Van Winkle

MINE fires are always dangerous and are frequently accompanied by loss of life during the period of confusion which is apt to follow their discovery. In metal mines, fires may result from the accidental ignition of some combustible material, or they may be of spontaneous origin resulting from the rapid decomposition of sulphide. They occur frequently enough to demonstrate the need of some special equipment and a general plan for controlling them, in addition to measures for their prevention. Nearly all the large copper mines have had fires, and the methods of fighting them have been well described in recent papers, notably-by C. L. Berrien,1 R.. E. Tally,2 and others in discussion. The Copper Queen mine has many shafts, which are connected by underground workings. The deeper parts are ventilated by fans, but in the shallower portions natural ventilation through numerous connecting raises or shafts is sufficient. There have been several fires in the past few years, of which all are extinguished but one, and that is under control. These notes cover particularly the preparations that are being made-to check a new fire, partially or temporarily, and to facilitate the escape of workmen in the interval before a definite plan of fighting it can be established. A fire may occur in a shaft or station, or in some working father away. In case of fire in an upcast shaft, the gas would escape to the surface and the immediate result would probably not be dangerous to workmen, as they could escape by other shafts. In a downcast shaft, however, the gas would be distributed very rapidly throughout a large portion of the mine, and men might easily be trapped and asphyxiated. A fire in mine workings, drift, raise, or stope, would be dangerous in a degree, but the draft there is likely to be less strong than in a shaft and probably a smaller area would be invaded by the fire gases.

Jan 1, 1918

By George A. Guess

The increasing demand for greater speed and more accuracy, in making daily assays of ores and products from mills treating material containing but very small quantities of lead and copper, has caused the older analytical methods to be supplanted by new ones devised to meet the needs of modern work. For " control" work in copper-analyses, I had, previous to the present equipment, introduced in my laboratory the ordinary electrolytic method, using hollow cylindrical electrodes; and with these I began a series of experiments in determining the lead-content of daily mill-samples and controls. The results, proving accurate and satisfactory, I then devised, with Mr. H. E. T. Haultain, a cheaper electrode than the ordinary jaCket-electrode, which costs from $15 to $20,—the expense of the older form making the installation of many units very costly. The form of cathode finally adopted as the most satisfactory, shown in Fig. 1, is cut from 0.001-in. platinum foil. It is 12.5 cm. long, and is divided into a blade 4 cm. wide and 6.25 cm. long, and a tongue 0.7 cm. aide and 6.25 long, the immersion area being 50 sq. cm. and weight 1.5 grams. The blade is first sand-blasted and then corrugated lengthwise, in order to impart the necessary rigidity. Strips of platinum foil 0.001 in. thick, 12.5 cm. long and 0.5 cm. aide, having a median corrugation, form the anodes. Three electrodes are used in each cell; one anode in the middle and one cathode on each side of the anode. These electrodes are connected to slotted aluminum terminals, in which they are held by contact pressure. The terminals are 5/16in. rods, projecting 2 in. horizontally in front of the wall of the cabinet; at the back the middle electrode (anode) is connected with one pole of the current, and the two outer ones (cathodes) with the other pole.

Jan 1, 1906

SIDNEY ROLLE, Chrome, N. J.-I should like to ask if Mr. Bach does not think it rather harmful to let the amen depend entirely on the company, whether it would not be a good plan to let the men aid a little in the support of these organizations? Also whether he has had any experience with utilizing the Y. M. C. A. in this connection. E. E. BACH, Ellsworth, Pa.-That question is always raised whenever there is discussion upon this subject. So far as we are concerned that would not help a bit; our people do not have that feeling, because .we have a company which these men recognize has a corps of very sympathetic officials in every way. I remember the assistant general manager lived out in one of these mining towns for a while. His difficulty was that every man, no matter what, who or where he was, if he had, or thought lie had, a, complaint, had the right of way to his office, and didn't have to stop at all. That is the spirit that predominates all through it. This is also the spirit of the mine foremen, two of whom were trained in our own night school, and it is the spirit of the fire boss and the general spirit of the people. They do not feel that we are trying to feed them with a spoon. As to the Y. M. C. A., we feel that it would be impracticable for us. R H. VAIL, New York, N. Y.-It would be very interesting if Mr. Bach would tell a little more about the control of the dispensing of intoxicants. There are many communities where the state intends to do that but does not succeed very well, and as Mr. Bach has spoken of the speakeasies on the environment of these towns, it would he well to know more about the problem of eliminating those.

Jan 4, 1918

By Thomas A. Wright

No symposium on die-casting could be complete without consideration of the methods of formula and impurity control. No corisideration of control would be complete without discussion of that new tool of the analytical chemist and inspector, the quartz spectrograph. Just as there is an increased appreciation of the possible applications of the die-casting process and of die castings, so too is there, slowly but surely, of the spectrograph. At present the role of the instrument might well be compared with that of brass or magnesium die castings. Neither is as widely understood or known as they will be. Product specifications are increasing and are getting more explicit and often more rigid. The designer, metallurgist and production engineer or superintendent will be forced to depend more and more on the chemical laboratory. Sampling, as well as analyses, testing and inspection problems will grow. The chemical laboratory must meet its increased responsibility and use of the spectrograph will become more common. Advantages of increased precision, greater speed, lessened labor and often lower costs cannot be ignored. It will be the purpose of this paper in part to outline the respective fields of chemical and spectrographic analyses and to indicate where one may overlap the other and in part to indicate certain possible sources of contamination of zinc-base die-cast alloys in particular. Composition Aluminum.-Aluminum die die castings are expected to conform to the specifications of the Amcrican Society for Testing Materialslt and the Society of Automotive Engineers2. The A.S.T.M. has recognized seven aluminum alloys in Tentative Specification B85-33-T. TWO are straight silicon and the remainder are of the copper-silicon type of which alloys VIII and IX have in addition respectively 2 and 4 per cent of nickel, but unlike the others are not covered by S.A.E. as well. All seven call for rigid control of certain impurities. With the exception of alloy XII,

Jan 1, 1935

By B. W. Adams, R. W. Shilling

9.4-1. Basic principles. DESCRIPTION AND BASIC FUNCTIONS. The concept of inclined skip haulage is not new. The basic idea has been in use at least 400 years. The system is essentially a steeply inclined railway utilizing a hoist to pull the skips to the top or intermediate positions. Inclined skip haulage is often justified where high lifts would require long hauls for other haulage systems. The basic system types are as follows: 1. Single skip, single drum. This system is a single car pulled by a simple hoist system. 2. Balanced skip, single drum. A system utilizing two cars (skips on cables)--one overwound, one underwound-on a single drum. The dead weight of one skip and cable balances the dead weight of the other. As one skip ascends the other descends between two fixed points. 3. Balanced skip, double drum. This system is an elaboration of system No. 2, except the drums may be disengaged from one another to permit the skips to service various loading and dumping points. The preceding are major classifications subject to numerous variations. These variations may be in the skipway, skip design, loading methods, or unloading methods. A few examples follow: 1. The skipway may be standard or special railroad, an overhead monorail or cable, or a ramp for rubber tired vehicles. 2. The skip, per se, may be of varying dumping arrangements (side, bottom, etc.) or could be the box of the vehicle hauling to the skip. 3. Loading may be accomplished directly from the service unit to skip, through an intermediate loading device (e.g., a pocket), or into bins which feed the skip. Loading may be at more than one point. 4. Unloading of the skip can be simple or complex as required. Dumping may be to the haulage unit, to bins and feeders, or to a crusher and conveyor system. Dumping may take place at more than one point.

Jan 1, 1968

By Samuel M. Cassidy

The exact date of man's first use of coal is lost in antiquity. The discovery that certain black rock would burn was undoubtedly accidental and probably occurred independently and many times in the world over thousands of years. It is quite likely that these independent discoveries were made when primitive man chanced to build camp fires on exposed ledges of a black rock, then was amazed when it caught fire. The Chinese recorded the use of coal 1100 yearn before the Christian Era and from the Bible we learn that King Solomon was familiar with coal in what is now Syria. In Wales, there is evidence that the Bronze Age people used coal for funeral pyres, and it is known that the Romans used this fuel. There are other ancient references. So the knowledge that coal would burn, and even some uses of that knowledge, go back thousands of years. However, practical and consistent use of coal seems to date to England in the Middle Ages. COAL IN AMERICA In the Americas, there is evidence here and there of occasional use by the Indians. However, the first recorded discovery of coal, in what is now the US, was by French explorers, who reported an outcrop exposure on the Illinois River in 1679. Following this, other discoveries were made by French and British explorers, but the first recorded actual usage was in Virginia in 1702, where a French settler was granted permission to use coal for his forge. Earliest recorded commercial mining was in 1750, from the James River coaEeld near Richmond, VA, a deposit now abandoned. Besides local consumption from this field, shipments were made to Philadelphia, New Pork, and Boston. During the Revolution this coal was of impor- tance in the manufacture of shot and shell; so important, in fact, that the British sent an expedition in 1781 to destroy the iron works and

Jan 1, 1981

By Earl C. Henry

Magnetic iron ore was mined in Essex County, N. Y., during the American Revolution; Benedict Arnold is said to have mined ore near Port Henry to secure iron for chains and spikes for the Lake Champlain fleet. Details regarding the operations prior to 1804 are not easily obtained but work on a commercial scale appears to have been started about 1838. The Witherbee, Sherman & Co. was established in 1849. The property of the district is held in fee almost entirely by the mining companies. The Mineville iron-ore district, as well as the entire Adirondack region, belongs to the pre-Cambrian complex. The readily identified rocks consist of gabbro, anorthosite, syenite, and granite, and are classed as igneous, eruptive, and intrusive. In addition, there is a great variety of gneisses, rocks with a variable mineral composition but all more or less distinctly foliated. The Grenville series are the oldest rocks in the district; this series consists of graphitic white limestones, graphitic sandstones, and quartzites and gneisses with or without graphite. The orebodies occur in the gneissic rocks and are comformable to the structure of the rocks. The typical occurrence of the ore in this district is in lenticular bodies with a parallel pitch to the southwest; this structure is best exemplified in the New Bed mine. The Harmony and Old Bed orebodies are faulted by two sets of diabase dikes, one set having a southwest strike and the other set an east-west strike. The ores occurring in the acid gneissic rocks are non-titaniferous. The ores occurring in the gabbros and anorthosites are high in titanium; these deposits are irregular, have no structural relation with one another, and are unquestionably of igneous origin. The origin of the gneissic rocks and the ores therein contained is not settled; both the sedimentary theory of ore concentration and the igneous theory of magmatic segregation have been advanced. The iron mineral in all the orebodies is crystalline magnetite; some very perfect and large specimens have been obtained. The gangue is

Jan 1, 1925

By Robert A. Cook

Among the new devices for cheapening the cost of material entering into the manufacture of iron is the mechanical drawing of coke, by which the coke from bee-hive ovens is extracted with a minimum of manual labor. About twenty years ago, an ordinary plate-conveyer was put in use at the plant of bee-hive coke-ovens owned by the firm of Bell Bros. & Co., near Middlesboro, England. This conveyer ran close along the front of the ovens, and carried the coke to the cars. The ovens were drawn by hand, and a very great saving in cost was secured, as one man could draw and clean out twice as many ovens after the conveyer was put in use—he having no forking to do, and the coke being carried away as fast as it was drawn to the mouth of the oven. The next step was further to eliminate hand-labor as far as possible; and Mr. Thomas Smith of the Thorncliffe Iron Works, near Sheffield, patented in 1891 the machine for drawing coke which I here describe. This machine, the outcome of several years of experimenting, has now been in successful use since 1891, and there are between twenty and thirty of them in operation at present, and others building. The machine, as may be seen from Figs. 1 and 2, consists of a wedge-shaped shovel of proper width and thickness, connected with a steel rack of sufficient length to reach the back of the oven. The rack is supported by rolls, and guided by a device operated by a hand-wheel, which directs the shovel in the oven. The rack is driven by a pinion on a vertical shaft carrying a bevel-gear on the upper end. This bevel-gear is driven by another on the engine-shaft. The engine is single-cylinder, with reversible gear; and engine and machine are mounted on a truck, which is propelled

Jan 1, 1897

By Richard B. Moore

The successful commercial production of helium during the last few years has added greatly to its scientific interest. When the quantity of an element available for experimental purposes increases within a few years by 200,000 per cent., both public and scientific interest in the element are greatly stimulated. Before the war, probably, there was not more than 10 or 15 cu. ft. of helium in existence. The larger part of this was owned by Prof. Kam-merlingh Onnes, and was used by him in connection with his low-temperature work at Leiden. By experimental work during the war and immediately afterwards, the Canadians, under Prof. J. C. McLennan, produced about 60,000 cu. ft. of helium of various grades of purity. Up to Dee. 1, 1921, when the plant at Fort Worth was shut down because of lack of funds, there had been produced during the experimental work by the U. S. Government, during the war and afterwards. 2,300,000 cu ft. of helium averaging between 92 and 95 per cent. purity. After the new appropriation was made in 1922, the production plant was again started and at the time of writing was making about 15,000 cu. ft. of helium a day. Only three of the five units were being operated because of the inability to get sufficient gas to run at full capacity. The gas supply is owned by two companies and on account of a disagreement between them, it has been possible for some time to get gas from only one. It is expected that when all five units are running steadily, the daily production will be between 30,000 and 40,000 cu. ft. of gas averaging from 93 to 95 per cent. purity. All three experimental plants used during the war have been shut down. The Air Reduction plant, using the Claude system, and the Linde

Jan 1, 1923

By Richard B. Moore

The successful commercial production of helium during the last few years has added greatly to its scientific interest. When the quantity of an element available for experimental purposes increases within a few years by 200,000 per cent., both public and scientific interest in the element are greatly stimulated. Before the war, probably, there was not more than 10 or 15 cu. ft. of helium in existence. The larger part of this was owned by Prof. Kam-merlingh Onnes, and was used by him in connection with his low-temperature work at Leiden. By experimental work during the war and immediately afterwards, the Canadians, under Prof. J. C. McLennan, produced about 60,000 cu. ft. of helium of various grades of purity. Up to Dee. 1, 1921, when the plant at Fort Worth was shut down because of lack of funds, there had been produced during the experimental work by the U. S. Government, during the war and afterwards. 2,300,000 cu ft. of helium averaging between 92 and 95 per cent. purity. After the new appropriation was made in 1922, the production plant was again started and at the time of writing was making about 15,000 cu. ft. of helium a day. Only three of the five units were being operated because of the inability to get sufficient gas to run at full capacity. The gas supply is owned by two companies and on account of a disagreement between them, it has been possible for some time to get gas from only one. It is expected that when all five units are running steadily, the daily production will be between 30,000 and 40,000 cu. ft. of gas averaging from 93 to 95 per cent. purity. All three experimental plants used during the war have been shut down. The Air Reduction plant, using the Claude system, and the Linde

Jan 1, 1923

By Samuel M. Cassidy

The exact date of man's first use of coal is lost in antiquity. The discovery that certain black rock would burn was undoubtedly accidental and probably occurred independently and many times in the world over thousands of years. It is quite likely that these independent discoveries were made when primitive man chanced to build camp fires on exposed ledges of a black rock, then was amazed when it caught fire. The Chinese recorded the use of coal 1100 years before the Christian Era and from the Bible we learn that King Solomon was familiar with coal in what is now Syria. In Wales, there is evidence that the Bronze Age people used coal for funeral pyres, and it is known that the Romans used this fuel. There are other ancient references. So the knowledge that coal would burn, and even some uses of that knowledge, go back thousands of years. However, practical and consistent use of coal seems to date to England in the Middle Ages. COAL IN AMERICA In the Americas, there is evidence here and there of occasional use by the Indians. However, the first recorded discovery of coal, in what is now the US, was by French explorers, who reported an outcrop exposure on the Illinois River in 1679. Following this, other discoveries were made by French and British explorers, but the first recorded actual usage was in Virginia in 1702, where a French settler was granted permission to use coal for his forge. Earliest recorded commercial mining was in 1750, from the James River coalfield near Richmond, VA, a deposit now abandoned. Besides local consumption from this field, shipments were made to Philadelphia, New York, and Boston. During the Revolution this coal was of importance in the manufacture of shot and shell; so important, in fact, that the British sent an expedition in 1781 to destroy the iron works and

Jan 1, 1981