Search Documents

By John O. Farmer

The wire-line tubing perforator is a mechanically operated tool that is run on an ordinary steel measuring line into the tubing of a well, under pressure, to drive into the wall of the tubing, and securely lock in place, a tapered, cylindrical insert containing an orifice. Use of the perforator obviates the necessity of pulling and rerunning the tubing to install jet collars or flow valves, reduces the cost, and simplifies the task, of placing an oil well on gas-lift operation. More important, however, is the use of the tool with a removable check valve and stop, to provide a means of washing drilling mud from the annulus between the tubing and casing, and to complete the well for gas lift operation without exposing the producing formation to the mud column and without moving the tubing string. This paper discusses the origin, development, and mechanics of the wire-line perforator, the various purposes for which the tool was designed, and the method of selecting orifice sizes for any depth, and gives the results obtained thus far in practical application. Origin and Development Several years ago, a tool that could be lowered on an ordinary steel measuring line into the tubing of a well under pressure was designed and constructed for the purpose of punching a hole in the tubing walls above a shale bridge that had completely plugged the tubing of a well in the Long Lake field, East Texas. The well was in a low, swampy area, which excessive rainfall had caused to be in- accessible by car or truck for about four months. The only equipment at the well site consisted of an ordinary steel wire line that had been carried there to measure the depth of the bridge. Since a pulling unit could not be moved to the well site, and as the pressure on the casing was 2100 lb. per sq. in., it became apparent that the only way out of the predicament was to make a perforating tool that could be lowered into the tubing on a measuring line and operated under Pressure. Thus, the first wire-line tubing perforator was designed and built as an expedient, and was not used extensively until it had been redesigned to meet more frequent and increasingly urgent needs. Until recently, it was necessary to pull the tubing to install jet collars or flow the when a well was to be placed On gas lift. Because most companies either maintained or had access to pulling units and crews for this work, little or no thought had been given to eliminating or even simplifying this task. When the manpower and steel shortage became so acute, however, many operators suddenly found themselves without facilities to equip their wells for gas lifting. The wireline tubing perforator already had been tried and proved successful, therefore operators immediately requested its use to punch gas-jet holes in the tubing, to eliminate the pulling and running of tubing strings. The first deficiency revealed by more general use of the perforator lay in the inability to regulate the size of the hole punched through the tubing. The size could not be controlled to any degree of

Jan 1, 1946

By John O. Farmer

The wire-line tubing perforator is a mechanically operated tool that is run on an ordinary steel measuring line into the tubing of a well, under pressure, to drive into the wall of the tubing, and securely lock in place, a tapered, cylindrical insert containing an orifice. Use of the perforator obviates the necessity of pulling and rerunning the tubing to install jet collars or flow valves, reduces the cost, and simplifies the task, of placing an oil well on gas-lift operation. More important, however, is the use of the tool with a removable check valve and stop, to provide a means of washing drilling mud from the annulus between the tubing and casing, and to complete the well for gas lift operation without exposing the producing formation to the mud column and without moving the tubing string. This paper discusses the origin, development, and mechanics of the wire-line perforator, the various purposes for which the tool was designed, and the method of selecting orifice sizes for any depth, and gives the results obtained thus far in practical application. Origin and Development Several years ago, a tool that could be lowered on an ordinary steel measuring line into the tubing of a well under pressure was designed and constructed for the purpose of punching a hole in the tubing walls above a shale bridge that had completely plugged the tubing of a well in the Long Lake field, East Texas. The well was in a low, swampy area, which excessive rainfall had caused to be in- accessible by car or truck for about four months. The only equipment at the well site consisted of an ordinary steel wire line that had been carried there to measure the depth of the bridge. Since a pulling unit could not be moved to the well site, and as the pressure on the casing was 2100 lb. per sq. in., it became apparent that the only way out of the predicament was to make a perforating tool that could be lowered into the tubing on a measuring line and operated under Pressure. Thus, the first wire-line tubing perforator was designed and built as an expedient, and was not used extensively until it had been redesigned to meet more frequent and increasingly urgent needs. Until recently, it was necessary to pull the tubing to install jet collars or flow the when a well was to be placed On gas lift. Because most companies either maintained or had access to pulling units and crews for this work, little or no thought had been given to eliminating or even simplifying this task. When the manpower and steel shortage became so acute, however, many operators suddenly found themselves without facilities to equip their wells for gas lifting. The wireline tubing perforator already had been tried and proved successful, therefore operators immediately requested its use to punch gas-jet holes in the tubing, to eliminate the pulling and running of tubing strings. The first deficiency revealed by more general use of the perforator lay in the inability to regulate the size of the hole punched through the tubing. The size could not be controlled to any degree of

Jan 1, 1946

By J. D. Pennock

About a year and a half ago, Mr. Morris, an engineer of the Solvay Process Company, was sent to Belgium and France to study the manufacture of coke in the Semet-Solvay ovens, which were in operation at Havre. With complete plans of construction and a good understanding of the methods of running the ovens, he returned to Syracuse. Work on twelve Semet-Solvay ovens was immediately begun. These ovens, with plant for crushing and washing coal, and the necessary condensers, scrubbers, and concentrator for the recovery of the byproducts are nearly finished, and will soon be in operation. As the work approached completion it became necessary to determine what coal should be used. Accordingly, a chemical investigation of the various bituminous coals was made. I. Investigation of Coals. The samples of coal taken for analysis were: I. A sample of Reynoldsville coal that had been exposed to the weather for a year; 11. Reynoldsville coal taken from a car direct from the mine; 111. Morris Run lump coal; IV. Morris Run fine coal; V. Coal from the Fairmount Coal and Coke Company; VI. A special enginecoal from Pardee colliery, Phillipsburg, Pa.; VII. South Fork, Pa., coal; VIII. Coal from Laceyville, Ill.; IX. Pittsburgh bituminous coal from Ocean mines (gas-coal); X. Steubenville, Ohio, coal; XI. Evansville, Indiana, coal; XII. Coal from the Ohio Coal Company. Proximate Analysis. I. 11, 111. IV. V. VI. Water at 90° C.,* ..................................... Volatile,. .. 31.14 33.00 17.73 18.12 37.20 23.86 Fixed Carbon,. . 64.49 58.07 71.92 71.89 56.68 73.00 Ash,. .. 4.37 8.93 10.35 9.99 6.12 3.14 Coke,. .. 68.86 67.00 82.27 81.88 61.88 76.80

Jan 1, 1893

By Frank C. Canney

The word "other" in paragraph 4, line 11, column 1, page 205, should read "over;" the correct version of reason 2, this paragraph, is: 'L. . . 2) to evaluate the usefulness of certain geo-chemical techniques, V. C. Kennedy and S. W. Hobbs of the USGS had already studied the distribution of copper, lead, and zinc in the soils (both in background areas and over veins) and in the water and plants, providing a criterion for measuring the magnitude and effect of soil contamination; ...9 On page 206, in the top left hand corner of Fig. 1 (in the area bounded by 47°35' and 116°10), the reference to Fig. 3 is incorrect. The area of Pine Creek, South Fork Coeur d'Alene River, and portion of Big Creek (the area which includes, from left to right, Kingston, Pinehurst, Smelterville, and Kellogg) should be identified as that of Fig. 2A. The headings for columns 1, 3, and 4, Tables I and 11, page 209, column 2, were reversed when the paper was printed. The corrected tables are:

Jan 1, 1961

By Oliver Bowles

SUPERFLUOUS varieties and standards which are meriting the critical scrutiny of the manufactur-ing industry have a special significance in the non-metallic mining industries, where, many of the final or intermediate products are manufactured at the mine or quarry. Such processes of manufacture must be considered an integral part of mining in its broader sense. Improvements may be either elimination or standardization. - The chief requirement of elimi-nation is an agreement between consumers and pro-ducers based on facts deduced from: statistical data. Standardization is much, more complex. Standards .may be established only when a very; thorough knowledge has been gained of the physical and chemical properties of the products, and the requirements of consumers. The activities of the Bureau of Standards are. largely directed toward such determinations. Paving-brick manufacturers, together with highway engineers, representatives of certain engineering socie-ties, and Government bureaus, have agreed that of the 66 styles of paving brick on the market 11 only are, essential and 55 are superfluous. Steps have been taken to reduce the output of -all but the 11 standard types. It is customary for manufacturers of structural slate to prepare it in sizes specified by builders and architects. Thus the material cannot be manufactured in advance and the result is irregular activity of mills, delays in filling orders, etc. To improve this condition, the Structural Slate Co. has issued a series of pamphlets giving complete specifications of structural slate for various purposes. Architects find it so much easier .to, order slate from these sheets that standard sizes are specified in preparing plans for new structures. Slate switchboards are usually manufactured after. the order has been received. One manufacturer claims that 80 per cent. of all switchboards are of standard sizes, and he keeps such sizes in stock. The facility with which orders may be filled from stock, and the improved quality of seasoned switchboards, will undoubtedly influence electrical, companies toward a more uniform standardization in size. Simplicity, could be further attained by the elimination of minor irregularities in .style; for example, in the beveled. edges.

Jan 2, 1922

By James Terry Duee

No important producing developments took place in Colombia during the year 1928. This was at least partly due to the paralysis of operations by the passage, during the latter part of 1927, of a law which was regarded by the oil companies as confiscatory and unjust, and the promulgation of exceedingly stringent regulations of this law under decree No. 150, published Jan. 28, 1928. This decree, which contained 24 articles, practically prevented not only producing operations by the oil companies but even such activities as geological explorations and surveying, as severe fines were imposed for the possession of maps not registered with the Ministry of Industries. Both this regulatory decree and the law were subject to attack in the courts by several of the oil companies. The regulatory decree was suspended May 22 by Presidential proclamation, until the suits against it are decided by the Supreme Court and Council of State. Though another law was introduced into the Colombian Congress at a later date, no action was taken on it, and at the time of the writing of this paper, it would appear that no oil bill will pass the Colombian Congress during the present session. The Barco concession, which was revoked in February, 1926, still continues an unsettled matter, although there have been rumors that the government was attempting to come to some decision on this rather difficult question. A hopeful sign toward the close of the year was the settlement of negotiations with the Tropical Oil Co. over the acceptance of the payment for royalties due the government from that company. This settlement, which covered a royalty on crude oil produced from June 30, 1926 to June 30, 1928, represented a cash payment for approximately 3,000,000 barrels. It is to be hoped that during the coming year the Colombian government will see its way clear to clarify its position on petroleum legislation. A good augury for the future was the statement made by President Abadia Mendez on New Year's Day, in which he courageously admitted the errors of previous legislation and said, regarding oil, "Very soon

Jan 1, 1929

Air-sand Process of Cleaning Coal Discussion of paper by THOMAS FRASER and H. F. YANCEY, presented at the New York Meeting, 1926, and issued, as Pamphlet No. 1561-F, with MINING AND METALLURGY, February, 1926. T. DEVENNY, Edgarton, W. Va.-How near the size of the sand can the coal to be treated be brought? Do you use an 8-mesh coal on that cleaner? J. J. RUTLEDGE, Baltimore, Md.-From the little I have seen of the apparatus in operation, I should say 8-mesh. In my experience in metalmine concentration work, trying to separate different minerals on one jig, sometimes I have succeeded and sometimes not. This apparatus has appealed to me; something of this kind should be useful with the silicates and carbonates of zinc. I think this apparatus has possibilities in metal mining. Recently in our coal field a screen has been introduced for cleaning coal; it is giving excellent service. When I asked the inventor why he did not take it to the metal mines, he said there was a good and sufficient reason, in a patent way. There may be reasons why it would not be applicable for metal mining; but the simplicity of it appeals to me and I cannot see why it could not be so used. T. FRASER (written discussion).-We feel that 8-mesh would be about -the minimum size of coal practicable to treat by the air-sand process. This would depend partly upon the friability of the coal. The more nearly the lower size limits of the coal- approaches the size of the sand, the more .time will be required in screening the sand out of the cleaned coal, which would mean a little more chance of breakage. In regard to the treatment of ores; this would necessitate the use of some heavier mediums than ordinary silica sand, or some other means of making the separation at a higher specific gravity than is required for coal. We are now working on a method of obtaining this effect for the preparation of anthracite coal without resorting to the use of heavier and more expensive material than common sand.

Jan 1, 1927

By D. P. Mitchell

Western Australia is the home of much that is new and interesting in the gold-mining industry. Some of the gold deposits are outranked for size and value by nothing yet discorered, while the value of the ores is, in many cases, rivaled only by their complex character. As in all parts of the world, many of the ore-bodies occur in ways which tax the skill of the miner in following them; and among these the writer considers the case of the East Murchison United more interesting than the average. This is one of the leading gold-mines of the colony in point of production, and is situated near the town of Lawlers, in the East Murchison district. The country for several miles around the mine is mainly granite, and the line of outcrop on which this mine is located can be traced for a long distance. As will be seen from the accompanying plan (Fig. I), there are, at the water-level, two nearly parallel veins running slightly north of west. Structural Features.—The most striking peculiarity of these veins, and the hardest to understand, is their tendency to send out horizontal stringers or side-veins. These vary in size from a veinlet an inch thick to a veil] several feet in width, and they extend with great persistence into the wall-rock on either side of the vein. This tendency is shown in Figs. 2 and 3. The usual signs of a movement of the wall-rocks, such as a ribbon-structure of the quartz and a well-defined gouge or seam of clay along the walls, are in many places lacking, while in other places they appear strongly marked. They seem more in evidence below water-level than above. It is a commonlly accepted idea that when a gold-bearing vein loses in width, it often gains in value. In this instance, however, the direct opposite is the case; for in many stopes it has been possible to leave the narrow portions of the vein to act as pillars, and to extract only the wide portions, which are

Jan 1, 1900

By Franklin J. Kay

Introduction The methods used in surface, mining vary throughout the world, depending on many variables such as: the types of over- burden materials, the depth of the overburden, the thickness of the seam, and other operational choices, both financial and functional. However, the stripping machines are typically draglines, stripping shovels, excavators, scrapers, loaders, and bulldozers. In all cases the economic feasibility of mining thin seams depends on the market needs, the market location, the equipment used, the mine management, the quality of the coal, and the labor market. Slight negative combinations of these parameters have closed many mines while positive combinations allow others to exist. The limited mobility or slow movement of large stripping shovels, draglines, and bucket wheel excavators make them more economically fitted to areas where large quantities of overburden are to be moved. This is necessary to keep the transfer and setup time between pits a negligibly small percent of the total operational time. Equipment such as the scrapers, loaders, backhoes, trucks, and bulldozers that are either very mobile or can be trailered is more versatile and can be used in the smaller area mines.* Mobile equipment is also more practical in areas with shallow overburden because of the constant movement required while removing overburden. In thin coal seams the equipment is usually paired such that the operational equipment can be listed as: (1) dragline-loader, (2) shovel-truck- loader, (3) scraper-loader. (4) loader-truck-loader, or (5) loader-loader. In these operations the overburden is removed with the first machine(s) of the pairing and the loader or loaders are used for coal production. Recent articles in Coal Age (Chironis, 1978) and Mining Engineering (Wiebmer, 1978) have discussed varying philosophies in mining similar seams of coal. One operator uses draglines for competitive mining while the other uses scrapers for the same purpose. Both cite strong cases sup- porting their choice of equipment as good sound economic decisions and their success supports their choices. The drag-line operation is adding new larger draglines to decrease the cost of mining, rather than to increase coal production. The scraper operation has also gone to more and larger scrapers for basically the same reasons. These operations and all

Jan 1, 1981

By Russell W. Mumford

LITHIA compounds have a place in pharmaceutical and other chemical industries and lithium minerals in glassmaking and ceramics. The metal, although rare, is used to a minor extent in alloys. During the nearly 50 years of production of lithium minerals in the United States, the silicate mineral spodumene has continued as the chief source of raw material for the manufacture of lithium salts. Although twice as much lepidolite, a lithium mica, has been mined, most of it has been used in the making of certain types of glass. Amblygonite has been an additional but minor source of lithium compounds. Triphylite, petalite, and zinnwaldite have also been utilized in the past. All of these commercial lithium minerals contain low percentages of lithium (Table 1). In 1938, a new raw material for manufacture of lithium compounds made its appearance. This product was crude dilithium sodium phosphate (Li2NaPO4), obtained as a by-product of manufacture of potash and soda chemicals from the brine of Searles Lake, California. Searles Lake, which is now dry, lies in the extreme northwest corner of San Bernardino County, California, and consists of a large mass of salts. It was estimated by the United States Geological Survey that the crystal body contained about 25 pct voids, which are filled with a saturated brine. The brine consists mainly of the sulphates, chlorides, carbonates, and borates of sodium and potassium. Several other acid radicals, including phosphates, are present. Lithium is present in the brine in an amount corresponding to 0.01 15 pct Li2O. In the course of evaporation of water from the brine, during the process of manufacture of sodium and potassium chemicals, dilithium sodium phosphate crystallizes out and is recovered by a flotation operation. The lithium concentrate is filtered and dried and is then ready for shipment. It analyzes from 19 to 21 pct Li2O and now constitutes the highest known grade of crude lithium material. It is and will continue to be a major source of lithium for manufacture of lithium products. The variation in lithia content of the commercial minerals as mined is due to replacement of the lithia by soda and potash, to partial alter-

Jan 1, 1949

By Shiou-Chuan Sun, R. F. Wesner, J. D. Morgan

FOR successful electrostatic separation, the behavior of the component minerals of the tested ore under various conditions should be known. In the course of investigation, it was found that these are difficult to measure accurately by the presently available methods. The method used by Johnson1 is handicapped by the fact that particles in the extreme front and rear end of the falling stream are difficult to control or observe accurately. Furthermore, this method is not applicable when the tested sample consists of more than one mineral. The deflection method, as reported by Fraas,' is inadequate to show the differential amounts of mineral particles deposited at the various horizontal positions under the grounded roll of the separator. This weakness is further noted when the tested sample contains more than one mineral. The purpose of this paper is to introduce a new method capable of measuring the behavior of mineral particles under various conditions, and of defining the optimum condition for separation. The main factors which influence the behavior of mineral particles in electrostatic separation are also described. dividing gauge and the two attached collecting chutes of a Johnson separator.~ This distribution analyzer consists of sixty or more 1.0-cm wide cells as shown in part in fig. 1; it has been fully described in a previous article." Except where otherwise stated, the testing procedure used in this paper is as follows: (a) calculate the weight of feed for a l-min run at a constant feed rate of one layer of closely packed particles falling on the grounded roll; (b) weigh and dry the feed at 100°C for 12 hr; (c) place the top of the distribution analyzer level 4 cm below the bottom of the grounded roll, so that the cells are longitudinally parallel to the grounded roll and the zero edge of a suitable cell is directly under the front vertical tangent to the grounded roll (see fig. 1); (d) with the charged roll at a negative potential of 15.5 kv, the dry hot sample is introduced into the feed chute at a constant feed rate; and (e)

Jan 1, 1951

By E. W. Davis

Iron-ORE beneficiation methods are determined largely by blastfurnace requirements. There are still many millions of tons of direct furnace ore in the Lake Superior district and blast furnaces are designed and operated for the most efficient use of this material. Beneficiated ore must be so prepared that existing furnaces may use it without alteration in design or radical changes in practice. Many attempts have been made to develop new furnaces or processes for smelting iron-ore concentrate not suitable for blast-furnace use, but these processes have gained little importance. It is, therefore, the endeavor in beneficiating iron ore to make a product that will give at least as good results as direct furnace ore in existing blast furnaces. The term "beneficiation," as applied to iron ore, does not necessarily mean concentration, but more accurately means "dressing up" the ore so that it is more acceptable to the blastfurnace operators. In modern blast-furnace practice the structure of the ore is quite as important as the chemical analysis. Certainly, the higher the iron content and the lower the silica, phosphorus and sulfur, the more desirable the ore bccomcs; but if the structure is bad, that is, if the blast-furnace gases can penetrate the charge only with difficulty, the ore is undesirable regardless of its analysis. This means that the ore should be as uniform in size as possible and free from fines, and also that the individual particles of ore should be pervious to the reducing gases of the furnace. Structure and purity are the primary requirements for a furnace ore and structure is just as important as purity. Iron-ore beneficiation processes can be divided, therefore, roughly into two main classifications: (1) processes that primarily improve the structure, and (2) processes that primarily improve the chemical analysis. During the past 10 years approximately 25 per cent of the ore shipped from the Lake Superior district has been beneficiated. Of this about half has been crushed and screened, a simple operation that primarily improves the structure but in some cases also improves the analysis slightly. The other half of the shipment of beneficiated ore, amounting to an average

Jan 1, 1935

By Shiou-Chuan Sun, R. F. Wesner, J. D. Morgan

FOR successful electrostatic separation, the behavior of the component minerals of the tested ore under various conditions should be known. In the course of investigation, it was found that these are difficult to measure accurately by the presently available methods. The method used by Johnson1 is handicapped by the fact that particles in the extreme front and rear end of the falling stream are difficult to control or observe accurately. Furthermore, this method is not applicable when the tested sample consists of more than one mineral. The deflection method, as reported by Fraas,' is inadequate to show the differential amounts of mineral particles deposited at the various horizontal positions under the grounded roll of the separator. This weakness is further noted when the tested sample contains more than one mineral. The purpose of this paper is to introduce a new method capable of measuring the behavior of mineral particles under various conditions, and of defining the optimum condition for separation. The main factors which influence the behavior of mineral particles in electrostatic separation are also described. dividing gauge and the two attached collecting chutes of a Johnson separator.~ This distribution analyzer consists of sixty or more 1.0-cm wide cells as shown in part in fig. 1; it has been fully described in a previous article." Except where otherwise stated, the testing procedure used in this paper is as follows: (a) calculate the weight of feed for a l-min run at a constant feed rate of one layer of closely packed particles falling on the grounded roll; (b) weigh and dry the feed at 100°C for 12 hr; (c) place the top of the distribution analyzer level 4 cm below the bottom of the grounded roll, so that the cells are longitudinally parallel to the grounded roll and the zero edge of a suitable cell is directly under the front vertical tangent to the grounded roll (see fig. 1); (d) with the charged roll at a negative potential of 15.5 kv, the dry hot sample is introduced into the feed chute at a constant feed rate; and (e)

Jan 1, 1951

By Robert W. Phelps

It is gratifying to observe the growing interest in the study of oil-well spacing. It should always be held in mind that the problem of optimum spacing is to obtain the maximum return of capital per acre drained. This naturally evolves.into a mathematical consideration. As mathematics is the basis of all science, an effort should be made to develop formulas which involve data obtainable in the early stages of development. The first information from a discovery well in a new field would be the character of the sand, rate of initial production of oil and gas, viscosity of the oil, rock pressure, etc. Later, from this well, if Herold's theories of hydraulic, volumetric and capillary controls are accepted, could he determined the ultimate production as without interference from drainage by subsequent well completions, and under which control the well is producing. If it should prove to be producing under capillary control, a rough estimate could be made of it's radius of drainage. With but one well, the radius of drainage, or the interference of drainage of individual wells by close spacing, would be estimated by comparison with similar conditions in other fields in which the development has progressed sufficiently to furnish the data. A second well that is spaced sufficiently close so that an interference can he observed after its ultimate production is estimated, will furnish data to develop a desirable spacing of wells which can be inaugurated for that area and which is capable of producing a uniform amount of oil under like conditions. In some fields this area will be extensive, in others each well location will require an individual study. In 1924, Cutlerl developed a scheme whereby he determined by tabulation a spacing of oil wells for the maximum return per acre. After a study of production in a number of fields, he developed the following as a tentative rule: "The ultimate production for wells of equal size in the same pool where there is interference (shown by a difference in the, production decline curves for different spacing) seems approximately to vary directly as the square roots of the areas drained by the wells. This rule may also he stated thus: The recovery from wells of equal size

Jan 1, 1929

By Eric J. Bradshaw

For several hundred years the petroleum industry has flourished in Burma and at the close of the eighteenth century there were over five hundred producing wells in the Yenangyaung field. These were laboriously dug by hand and were exceedingly primitive, yet even today a small part of India's total production is obtained from hand-dug wells. The Indian Empire, the cradle of the oil industry, today produces but an unimpressive fraction of the world's supply of petroleum, not because the size of her contribution has diminished, but because it has remained more or less stationary while other countries have far outstripped her during the prodigious increase in the world's production of petroleum in recent years. Though for the past 10 years the total production in India has been remarkably constant, it has become increasingly difficult to maintain this output and at any rate from the older fields a slow decline may be anticipated unless new productive horizons are discovered. Production figures for the 10 years 192&1929 (the last year for which figures are available) are given by fields in Table 1. Crudes of Burma and Assam The bulk of India's production comes from the Yenangyaung and Singu fields, from which the crudes are very similar, the only important difference being that the oil from the Singu-Yenangyat structure contains a higher percentage of lighter fractions. The Burma crudes resemble that of the Panhandle of Texas and have a high content of solid paraffin, though strictly speaking the oil is of mixed base with a low content of asphaltum. With the exception of the negligible production from Sabe, the Burma crudes do not require dehydration; the sulfur content is very low and is innocuous. A small amount of naphthenic acids occurs in the kerosene and intermediate oil fractions while the lubricating fraction is practically free from acid. The ash content is low and the average A.P.I. gravity of mixtures of Yenangyaung and Singu oil is 36.4. Burma crudes require only light refinery treatment and practically dl the fractions are merchantable. Part of the gasoline supply is stripped

Jan 1, 1931

By R. E. Zimmerman

ALTHOUGH flotation of coal is considered relatively new in the United States by coal-preparation engineers, actually it has been practiced to some extent for the past 30 years, It is practiced much more widely in Europe than in the United States. Commercial plants are operating in nearly all major coal-producing countries of the world. A froth flotation plant has been operating since 1930 at the Champion No, 1 preparation plant of the Pittsburgh Coal Co. Unfortunately the term flotation is widely used in the United States by coal-preparation engineers to designate dense medium processes of coal cleaning. As used here, flotation means those processes for cleaning fine sizes of coal in which the coal is collected in a froth or matte at or near the surface of a pulp. The refuse particles remain in the pulp. Two distinct types of flotation are practiced: froth flotation and agglomeration. FORMS OF FLOTATION The theory of the principles of flotation and of the physicochemical foundations surrounding this process has become a complex and scientific field and coal-preparation engineers contemplating use of flotation processes would do well to study the works of Gaudin, 2, 5 Taggart, 3 Zimmerman, 4 Wark, 6 Ralston, 7 Petersen. 8 Bulk Oil Flotation.-In this process the separation of mineral from gangue is accomplished by virtue of the fact that minerals of metallic lustre, as sulphides, or hydrocarbons, as coal and graphite, are wetted preferentially by oil in the presence of water and consequently pass into the interface between oil and water; while gangue or rock is wetted by water and remains in the medium. Beginning in 1860 with Haynes and later between 1897 and 1907, at least 25 patents were granted for bulk oil flotation. Large quantities of oil are required, generally 3 to 25 per cent by weight of feed, and recovery of such oil is a major problem. The Elmore process 3 (1901 and 1902) is an example of a bulk oil process, The Trent process (1902-25) has been used for the cleaning of coal on a commercial scale, According to E. W, Davidson 9 there were five such plants operating in the United States by 1925. They have since been abandoned.

Jan 1, 1950

By Howard C. Pyle, John E Sherborne

Core analysis is a recent development in the field of petroleum technology. The earliest work on this subject was done in connection with evaluating and planning secondary oil recovery by water-flooding. Present-day analysis of sands of flush fields requires new and independent interpretations of the data provided by cored material. Particular attention is being paid to the development of rapid, routine methods for measuring physical characteristics of sandstone, such as permeability, porosity and grain size, as well as the sand's fluid content. Permeability may be defined as the fluid-passing capacity of a rock. For a sandstone to be permeable it must be possible to pass a measurable quantity of fluid through the material in a finite period of time. The common unit of permeability is the darcy, which may be defined as the rate of viscous flow, in milliliters per second, of a fluid of one centipoise viscosity through a porous medium having a cross section of one square centimeter, under a pressure gradient of one atmosphere (76.0 cm. Hg) per centimeter.' For convenience the subunit millidarcy, or one-thousandth darcy, is often used. Porosity is defined as the fluid-containing capacity of a rock and is usually expressed as a percentage ratio of the total pore volume to the rock or bulk volume. Since measurement of only the effective or communicating pore volume is often made, porosities are distinguished as total or effective.2,3 Net effective porosity is defined as the net pore volume available for oil and gas. Oil and water content of sand is measured and expressed either as the percentage saturation of the total pores or of the bulk rock. The oil content may also be expressed as the percentage saturation of the net effective pores. In connection with water-flooding, methods of core analysis were developed to furnish data that could be used in determining the quantity of recoverable oil14-6 and the probable rates at which various sands or divisions of a sand open to the wells would take water or produce oil. In flush fields, the analytical data are used to predict the productivity of a cored interval. They indicate the presence of oil, gas and water and may

Jan 1, 1939

By Cyril Stanley Smith

Although not of the same importance as electrical conductivity, the capacity for conducting heat is nevertheless a very important property of metals and alloys. A knowledge of thermal conductivity is of value in selecting alloys for many purposes and in the calculation of the efficiency of apparatus which is being designed. Unfortunately, the determination of thermal conductivity is extremely slow and tedious, consequently few data have been obtained. A further reason for the lack of information is that there has long been an impression that the thermal conductivity of an alloy is directly proportional to the electrical cónductivity and that it can therefore be calculated from the latter. The Wiedmann-Franz-Lorenz law of constant ratio of the two conductivities holds with a considerable degree of precision for all the pure metals, but appreciable deviations occur in certain alloys—particularly those containing nickel—and it seems difficult to predict exactly what the ratio will be. Therefore direct determinations of thermal conductivity should be made whenever the results are needed with any accuracy. This research is intended eventually to cover all the alloys of copper that are of commercial importance, including the binary alloys of copper with zinc, tin, aluminum, nickel, silicon, manganese, cadmium and phosphorus, and the ternary alloys copper-nickel-zinc, copper-nickel-silicon, copper-manganese-silicon, copper-zinc-tin, etc. Most of these alloys are customarily used in the wrought condition and therefore were tested in the form of annealed rods. A limited number of sand castings were also obtained and examined. This paper contains a complete review of all the previous work that has been done on copper alloys, and includes a detailed description of the apparatus and method of procedure used in the present research, together with the new results obtained on the copper-zinc series, which is the only one completed at the present time. Subsequent papers describing the other alloys will contain the experimental results and discussion only. Previous Work Copper The conductivity of copper has been studied by many observers since the pioneer work of Wiedemann in 1859. The majority of these measure-

Jan 1, 1930

By John V. W. Reynders

Our entry into the World War suddenly brought home to us in a startling way the vital importance of manganese. Since the war, much has been written and said upon the subject of manganese and a great deal of time and money have been spent in attempts to find an adequate substitute for this metal in the manufacture of steel; none has been found. It is true that ways are known by which it is possible to make small amounts of good steel without manganese, but taking into consideration the diminishing quality of iron ores and fuels as well as the increasing exaction of specifications for finished products, it may safely be assumed that, high-grade manganese ore will be more and more a necessity in the production of steel as time goes on. Taking world resources as a whole it may be well to point out that the problem of obtaining needed supplies of manganese from a strictly commercial viewpoint is now less serious than it was before the war. Formerly it was feared that world resources of high-grade manganese ore might be exhausted in a relatively short time, but, largely as a result of the stress laid upon the importance of manganese during the war, the world's available supply of high-grade manganese ore has been greatly augmented by new discoveries and fuller development of previously known deposits. Sources of Production Russia alone, of countries producing the major part of the world's stee1, has within its geographical boundaries sufficient manganese to supply its needs. The domestic production of England is inadequate and English requirements for high-grade manganese are supplied principally from India. France also draws largely upon India, as it depends upon foreign sources of supply except with respect to a small tonnage of silico-manga-nese and silico-spiegel produced in the Hautes-Pyrénées. Germany and the United States likewise depend upon foreign sources of high-grade ore, though each possesses comparatively large reserves of ferruginous manganese ore and manganiferous iron ore. At present the world demand for high-grade manganese ore is met with ease by the production of Russia, India, Gold Coast and Brazil.

Jan 1, 1927

By Howard C. Pyle, John E. Sherborne

Core analysis is a recent development in the field of petroleum technology. The earliest work on this subject was done in connection with evaluating and planning secondary oil recovery by water-flooding. Present-day analysis of sands of flush fields requires new and independent interpretations of the data provided by cored material. Particular attention is being paid to the development of rapid, routine methods for measuring physical characteristics of sandstone, such as permeability, porosity and grain size, as well as the sand's fluid content. Permeability may be defined as the fluid-passing capacity of a rock. For a sandstone to be permeable it must be possible to pass a measurable quantity of fluid through the material in a finite period of time. The common unit of permeability is the darcy, which may be defined as the rate of viscous flow, in milliliters per second, of a fluid of one centipoise viscosity through a porous medium having a cross section of one square centimeter, under a pressure gradient of one atmosphere (76.0 cm. Hg) per centimeter.' For convenience the subunit millidarcy, or one-thousandth darcy, is often used. Porosity is defined as the fluid-containing capacity of a rock and is usually expressed as a percentage ratio of the total pore volume to the rock or bulk volume. Since measurement of only the effective or communicating pore volume is often made, porosities are distinguished as total or effective.2,3 Net effective porosity is defined as the net pore volume available for oil and gas. Oil and water content of sand is measured and expressed either as the percentage saturation of the total pores or of the bulk rock. The oil content may also be expressed as the percentage saturation of the net effective pores. In connection with water-flooding, methods of core analysis were developed to furnish data that could be used in determining the quantity of recoverable oil14-6 and the probable rates at which various sands or divisions of a sand open to the wells would take water or produce oil. In flush fields, the analytical data are used to predict the productivity of a cored interval. They indicate the presence of oil, gas and water and may

Jan 1, 1939