Search Documents

Adams . Bernard . Student. South Dakota School of Mines .Rapid City . S . D . Ahlskog . Harold A. Student. Washington State College Pullman. Wash . Aldridge. John. Student. New Mexico School of Mines Socorro. N . M . Almstrom . Adne A .. Student. Met . Engrs.. Washington State College ..... .Pullman. Wash . Ancell . Virgil F.. Student. Missouri School of Mines Rolla. Mo . AnkudinoE. N., Mill Draftsman. Arthur G . McKee & Ch., 2422 Euclid Ave., Cleveland. Ohio . Avablaea . Salvador C.. Student. Univ. of California Los Angeles. Cal. Armstrong. Robert E .. Student. Lafayette College .Easton. P a Armstrong . Thomas E.. Student. Univ . of California Los Angela. Cal Aud. Robert A .. Student. Lafayette College Easton. Pa .

Jan 1, 1929

By Bruce A. Lamberton

In U. S. underground mines concrete work is not widely used. Timber and steel are cheaper, and there are few serious water problems. But in the Union of south Africa men dig deeper, more persistently, and probably more profitably than anywhere else on earth. Some gold mines near Johannesburg are below the 10,000 level and employ as many as 35,000 natives on a single property. Underground substations, pump chambers, and air conditioning plants have capacity to serve small cities. The complexity and extent of underground operations and the heavy subsurface water flows, especially in the new Free State gold fields, require heavy in a Deep concrete installations.

Oct 1, 1956

By J. L. Gillson

In this past year of our Institute's life, February 1960 to February 1961, we had some major problems to face, as did our members, since businesses in which they were engaged were feeling the recession. The major problems confronting us during this past year were: 1) Financing the new Engineering Center. 2) Keeping our three almost autonomous societies working together and toward a stronger AIME. 3) Cooperation with other engineering societies the Functional Plan. 4) Licensing and registration, and the Model Law. 5) The reorganization of the Council of Section Delegates. 6) Combatting the slump in the appeal of engineering to the young students.

Jan 4, 1961

By Robert A. Campbell, Robert J. Brison

The problem of optimizing from an economic standpoint the capacity of grinding equipment in the design of a new concentrator is discussed. Although directed specifically to copper flotation mills employing conventional wet, grinding, the material presented is considered applicable with modifications to other types of ores and other grinding methods. A general approach to optimizing the grinding capacity is outlined and illustrated by an example. The' interrelation between grinding capacity and other aspects of the project is considered. The problem of regrind capacity and its relation to preceeding and subsequent processing steps is also discussed. Finally, factors are considered that may, in certain cases, dictate modifications of the suggested approach.

Jan 1, 1974

NEW MEMBERS. The following list comprises the names of those persons who became members during the month of October, 1913: Members. BARNES, KENNETT F., Secty Granby Min. & Smelting Co., St. Louis, Mo. BILLINGSLEY, PAUL, Geol 526 Hennessy Bldg., Butte, Mont. BLANCHORD, RALPH C., Geol 3 Lombard St., London, England. BOYLE, ALBERT C., Jr., Prof. of Min. and Met., University of Wyoming, Laramie, Wyo. BRADFORD, JULIUS S., Min. Engr Chiksan Mining Co., Chiksan, Korea: CLEMES, ALFRED W., Min. Engr P. 0. Box 6,88, Moronic, Ariz. COPELAND, DURWARD, Met Cia. Estamifera de Llallagua, Bolivia, So. America. CRAWFORD, JOHN, JR., Mgr Noble Elec. Steel Co., Heroult, Shasta Co., Cal.

Jan 11, 1913

NEW MEMBERS The following list comprises the names of those persons who became members during the period Jan. 10 to Feb. 10, 1915: Members AGASSIZ, RUDOLPH Louis, Vice-Pres.,Calumet & Hecla Mining Co., Boston, Mass. AMIDON, RICHARD G., Min. Engr 3659 Girard Ave. N., Minneapolis, Minn. ANDERSON, HECTOR G. S., Min. Engr 323 N. 13th St., Muskogee, Okla. ANDERSON, JOHN CARTER, Petroleum Engr 2307 S. 33d St., Omaha, Neb. CLARKE, ALEXANDER FIELDER, Works Mgr., Firth-Sterling Steel Co., McKeesport, Pa. CROSS, CARLOS GARCIA, Min. Engr Calle Valparaiso 194, Vina del Mar, Chile. DAWSON, THOMAS WILLIAM, Min. Engr., Asst. Chief Engr., H. C. Frick Coke Co., Scottdale, Pa.

Jan 3, 1915

NEW MEMBER, The following list comprises the names of those persons who became members during the period Mar. 10 to Apr. 10, 1915: Members ADAMS, Louis WINFIELD, Supt., Rolling Mills, Lehigh Plant, Bethlehem Steel Co., So. Bethlehem, Pa.. ALLEN, ARTHUR WATTS, Mine Mgr Rodeo, San Juan, Argentina., BALL, EDWIN MARCOTTEL, Mine Supt., Ishkooda. Mines, Care Tenn. Coal, Iron & R. R. Co., H.F.D. 1, Birmingham, Ala. BOLN, CHARLES A., Oil salesman 135 S. 2d St., Philadelphia., Pa. BOYD, DAVID F., Naval Officer Navy Department, Washington, D. C. CAPERTON, GEORGE HENRY Charleston, W. Va. COGGESHALL, GEORGE W., Chem. Engr., Institute of Industrial Research, Washington D C

Jan 5, 1915

THOSE MARKED THUS * ARE MEMBERS, MARKED THUS ?ARE ASSOCIATES. THESE SIGNS DOUBLED INDICATE LIFE MEMBERS AND ASSOCIATES RESPECTIVELY. THE FIGURES AT THE END OF THE ADDRESS INDICATE THE YEAR OF ELECTION. HEAVY-FACED TYPE SIGNIFIES HONORARY MEMBERSHIP. *AARONS, J. BOYD, Vivian Gold Mining Co., Ltd., Harris, West. Australia. '05 *ABADIE, EMILE R., Cons. and Min. Engr., 214 Union Savings Bank Bldg., Oakland, Cal. '76 *ABBOTT, CHARLES W., Min. Engr. Pioche, Nev. ?08 *ABBOTT, JAMES W., Min. Engr: Ploche, Lincoln Co., Nev. '94 *AOTT, ROBERT R., Met. Engr., Peerless Motor Car Co., Cleveland, Ohio. '12 || ARAHAMS, ALEXANDER I., Student.. .67 E. 93rd St., New York, N. Y. '13

Jan 1, 1917

By G. C. Gardner

A new correlation of blast penetration in model and operating blast furnaces is presented which overcomes objections to prevzous correlations. It is shown that the tuyere diameter is only of small importance in determining the magnitude of the penetration. The data from operating furnaces correlate satisfactorily with the data from models whose cross section is a segment of a circle. A bubble-shaped gas space called a "raceway" normally exists in front of the nose of a blastfurnace tuyere. The periphery or "wall" of the raceway is well defined and is composed of densely packed charge particles. The blast. issuing as a jet from the tuyere, entrains gas from the raceway, in the usual manner of a jet, as it flows to the opposing wall. There it divides and flows back around the walls to be entrained once more. The blast must, of course, eventually leave the raceway and pass up through the charge column, but before it does it may, on the average, make several circuits of the kind described and in doing so it carries with it charge particles, which, because of their fast and circulating motion, suggested the name of "raceway". A fuller description of the raceway may be found elsewhere."' Here it is only necessary to mention, in addition, the measurement which characterizes its size. If an iron bar is pushed through the opened peepsight of a tuyere, .as far as it will go with ease, it will be stopped by the relatively impenetrable opposing raceway wall arid the distance that the bar has been pushed from the tuyere nose is called the "penetration". This measurement may be of practical importance and has; been the subject, with considerable success, of several attempts at correlation with other variables2-5 as stated in the next section. There is still, however, a serious objection to the most recent correlation,3 which is overcome by the correlation proposed in this paper. It will be shown that the objection is not trivial, in that the new correlation will attribute considerably different importance to the variables affecting the magnitude of the penetration. The data to be treated were made available by Wagstaff and are the same as those used in his correlation. They include measurements taken on small models, in which a cold air blast was used and no combustion occurred, and they also include data from operating blast furnaces at Wheeling and Fairless. The information from the blast furnaces will be shown to be in substantial agreement with those models whose plan views are segments of a circle and which are thus like segments of a blast furnace. First, Wagstaff's most recent correlation3 will be discussed and the objection will be given. Then the new correlation will be developed and its implications considered. CORRELATION OF J. B. WAGSTAFF Wagstaff's correlation is where and D — the penetration D,-the internal tuyere diameter V —the blast velocity in the tuyere

Jan 1, 1961

By D. Perry, G. W. Binkley, G. K. Dumbauld, F. A. Brooks

A new cementing technique has been developed which is particularly applicable to permanent-type well completion operations. The technique makes use of the accelerating effect of calcium chloride on setting time and strength development of cement cake deposited in squeeze cementing. An unique feature is that the accelerator is applied after the unaccelera-ted cement slurry has been squeezed and the excess has been reversed from the well. Laboratory data on the accelerating effect of calcium chloride applied to the fi1ter cakes of three low-water-loss cementing compositions demorzstrate that the procedure results in relatively rapid development of strength and impermeability of the cement cake. Simulated squeeze-ceinenting tests made in the laboratory likewise corroborated the practicality of the procedure. The laboratory tests showed that a newly developed oil-emulsion cemerzting composition is more susceptible to acceleration of set than are modified cements containing high percentages of bentonite. The acceleration procedure has been used successfully in field operations. INTRODUCTION Nature of Problem In squeeze-cementing operations, a substantial amount of time is consumed in waiting on the cement to develop strength after it has been squeezed into the well. Frequently, an interval of 18 to 24 hours or longer is required for the development of strength sufficient to prevent failure of the cement during subsequent operations in the well. Reduction of this waiting-on-cement time offers appreciable savings both in time and in money. A particular type of squeeze-cementing operation to which an increasing amount of attention has been given is encountered in permanent-type well completion operations wherein perforations are to be squeezed off1. In this procedure, it is customary to pump the cement slurry down the tubing and out into the perforated section through a retractable extension pipe. Squeeze pressure is then applied, which forces the cement slurry into the perforations and causes the build up of a compact filter cake of cement within the perforations. The excess slurry remaining in the hole is then removed by reverse circulation. The extension pipe is then retracted, and, if a new interval is to be perforated, a perforating gun is run through the tubing. The newly perforated interval may then be tested by swabbing. In such operations, it has been customary to allow approximately 20 hours or so for hardening of the cement squeezed into the perforations. This time interval is usually measured from the time that the cement is reversed out of the hole to the time that subsequent swabbing is started. If the cement has not developed strength at the commencement of swabbing, the pressure differential caused by swabbing results in failure of the squeeze job. At the time that the work described in this report was initiated, particular consideration was given to the reduction of waiting-on-cement time in squeeze cementing by the permanent-type completion technique. Consequently, much of the experimental work was directed to this specific objective, though the process which was developed for acceleration of strength development has possible application in other than permanent-type completion operations. Method of Attack Although quick-setting cements

Jan 1, 1957

By T. K. Prentice

ABSTRACTED AND REVIEWED BY E. W. DAVIS,* MEMBER A.I.M.E. THE January-February number of the Journal of the Chemical Metallurgical and Mining Society of South Africa is made up entirely of a discussion of Ball Wear in Cylindrical Mills. Following the principal paper by T. K. Prentice are several remarkably pertinent and carefully prepared discussions. Few persons in this country would be likely to see this publication, and since the information presented is new and of current interest, it seems desirable to abstract and review this publication for the benefit of the members of the A.I.M.E. The purpose of the investigation is stated in the first two paragraphs of Prentice's paper, as follows: Early in 1941, The Chamber of Mines Steel Products, Limited, initiated a series of tests under semi-working scale conditions to determine, if possible, those physical and chemical properties of a ball which make it resistant to wear when used in a cylindrical mill as a grinding medium, with the primary object of incorporating those beneficial qualities in the balls being produced at their works. This paper describes the tests carried out and discusses the results obtained. From these results it was possible to formulate a new theory relating to ball wear in cylindrical mills. This theory is presented in the second portion of this paper. PRACTICAL BALL-MILL TESTS IN A CYLINDRICAL MILL Part I of the paper begins with a discussion of the methods used for the manufacture of grinding balls in South Africa. The following paragraph is of particular interest. The cast steel ingots, 4 ¼ - in. square by 3 ft. 6 in. long, are re-heated in a gas-fired sloping stationary-hearth furnace and then rolled in a six-pass continuous mill into 2 5/8 in. round billets. Some of these billets are then removed and cut into suitable lengths for forging into 4 in., 3 ½ in., 3 in. or 2 ½ in. balls by means of three Drop and two Beché hammers, but the greater number, whilst still at about 1,000 ºC., pass directly into a set of scroll rolls which produce, in an ingenious manner, finished 3 in. balls direct from the 2 5/8 in. billets. Except in special cases, all balls are allowed to cool in the atmosphere and are not water quenched. Details of the Tests In order to enable the reader to evaluate properly the results and conclusions in the rest of the paper and in the discussions following the paper, most of the information presented by the author under this heading is quoted: ….. The testing unit was a nominal 30 in. diameter and 18 in. long centre discharge Denver Ball Mill. The ore pulp to the ball mill comprised a small portion of the normal feed to one of the fourteen City Deep 5 ft. 6 in. X 22 ft. tube mills, and the grinding media consisted of the balls under test plus other balls to give the desired load. The running time of the test-mill was divided into approximately equal periods of five days 13 ½ hours each. The usual procedure was to examine and make up the load

Jan 1, 1944

By T. K. Prentice

The January-February number of the Journal of the Chemical Metallurgical and Mining Society of South Africa, 1943, is made up entirely of a discussion of Ball Wear in Cylindrical Mills. Following the principal paper by T. K. Prentice are several remarkably pertinent and carefully prepared discussions. Few persons in this country would be likely to see this publication, and since the information presented is new and of current interest, it seems desirable to abstract and review this publication for the benefit of the members of the A.I.M.E. The purpose of the investigation is stated in the first two paragraphs of Prentice's paper, as follows: Early in 1941, The Chamber of Mines Steel Products, Limited, initiated a series of tests under semi-working scale conditions to determine, if possible, those physical and chemical properties of a ball which make it resistant to wear when used in a cylindrical mill as a grinding medium, with the primary object of incorporating those beneficial qualities in the balls being produced at their works. This paper describes the tests carried out and discusses the results obtained. From these results it was possible to formulate a new theory relating to ball wear in cylindrical mills. This theory is presented in the second portion of this paper. Practical Ball-mill Tests in a Cylindrical Mill Part I of the paper begins with a discussion of the methods used for the manu- facture of grinding balls in South Africa. The following paragraph is of particular interest. The cast steel ingots, 4¼ in. square by 3 ft. 6 in. long, are re-heated in a gas-fired sloping stationary-hearth furnace and then rolled in a six-pass continuous mill into 25/8 in. round billets. Some of these billets are then removed and cut into suitable lengths for forging into 4 in., 3¼ in. , 3 in. or 2½ in. balls by means of three Drop and two Beche hammers, but the greater number, whilst still at about 1,000, pass directly into a set of scroll rolls which produce, in an ingenious manner, finished 3 in. balls direct from the 25/8 in. billets. Except in special cases, all balls are allowed to cool in the atmosphere and are not water quenched. Details of the Tests In order to enable the reader to evaluate properly the results and conclusions in the rest of the paper and in the discussions following the paper, most of the information presented by the author under this heading is quoted: The testing unit was a nominal 30 in. diameter and 18 in. long centre discharge Denver Ball Mill. The ore pulp to the ball mill comprised a small portion of the normal feed to one of the fourteen City Deep 5 ft. 6 in. X 22 ft. tube mills, and the grinding media consisted of the balls under test plus other balls to give the desired load. The running time of the test-mill was divided into approximately equal periods of five days 13½ hours each. The usual procedure was to examine and make up the load

Jan 1, 1947

By T. K. Prentice

The January-February number of the Journal of the Chemical Metallurgical and Mining Society of South Africa, 1943, is made up entirely of a discussion of Ball Wear in Cylindrical Mills. Following the principal paper by T. K. Prentice are several remarkably pertinent and carefully prepared discussions. Few persons in this country would be likely to see this publication, and since the information presented is new and of current interest, it seems desirable to abstract and review this publication for the benefit of the members of the A.I.M.E. The purpose of the investigation is stated in the first two paragraphs of Prentice's paper, as follows: Early in 1941, The Chamber of Mines Steel Products, Limited, initiated a series of tests under semi-working scale conditions to determine, if possible, those physical and chemical properties of a ball which make it resistant to wear when used in a cylindrical mill as a grinding medium, with the primary object of incorporating those beneficial qualities in the balls being produced at their works. This paper describes the tests carried out and discusses the results obtained. From these results it was possible to formulate a new theory relating to ball wear in cylindrical mills. This theory is presented in the second portion of this paper. Practical Ball-mill Tests in a Cylindrical Mill Part I of the paper begins with a discussion of the methods used for the manu- facture of grinding balls in South Africa. The following paragraph is of particular interest. The cast steel ingots, 4¼ in. square by 3 ft. 6 in. long, are re-heated in a gas-fired sloping stationary-hearth furnace and then rolled in a six-pass continuous mill into 25/8 in. round billets. Some of these billets are then removed and cut into suitable lengths for forging into 4 in., 3¼ in. , 3 in. or 2½ in. balls by means of three Drop and two Beche hammers, but the greater number, whilst still at about 1,000, pass directly into a set of scroll rolls which produce, in an ingenious manner, finished 3 in. balls direct from the 25/8 in. billets. Except in special cases, all balls are allowed to cool in the atmosphere and are not water quenched. Details of the Tests In order to enable the reader to evaluate properly the results and conclusions in the rest of the paper and in the discussions following the paper, most of the information presented by the author under this heading is quoted: The testing unit was a nominal 30 in. diameter and 18 in. long centre discharge Denver Ball Mill. The ore pulp to the ball mill comprised a small portion of the normal feed to one of the fourteen City Deep 5 ft. 6 in. X 22 ft. tube mills, and the grinding media consisted of the balls under test plus other balls to give the desired load. The running time of the test-mill was divided into approximately equal periods of five days 13½ hours each. The usual procedure was to examine and make up the load

Jan 1, 1947

By George G. Binder Jr., James W. Lacey, Arthur L. Draper

An experimental investigation of miscible fluid displacement has been made in linear porous media under highly adverse mobility ratio conditions. Various refined oils were displaced at field rates by liquid propane in both horizontal and vertical models 9 to 36 ft in length. In horizontal tests, mixed zones or transition zones form between the two liquids early in the displace-lents. Initially, the zones grow rapidly. III 2-in. diameter models, the mixed regions become nearly stable zones from 6- to 20-ft long. From then on these quasi-stable zones apparently grow only by molecular diffusion. The lenghts of the quasi-stable zones appear to be almost independent of the core material in which displacement;; are made and increase with increasing rates of injection and oil/solvent viscosity ratios. The lengths of the quasi-stable zones. measured in 2-in. diameter models at viscosity ratios and injection rates anticipated in the field indicate that essentially piston-like displacements of oil by solvent would occur. However, the mixed zone lengths increase markedly as the model diameter increases. In vertical displacements controlled by gravity drainage, only short trans-sition zones form. The entire lenghts of these zones can be accounted for by molecular diffusion. Therefore, in reservoirs having characteristics allowing a high degree of gravity drainage, nearly complete oil recovery should be attainable by miscible fluid displacement. INTRODUCTION The oil industry is faced with an ever increasing cost for finding new oil reservoirs. This, coupled with the fact that conventional methods of oil recovery usually leave from 1 to 3 bbl of oil in the ground for every barrel produced, has aroused considerable interest in developing more efficient methods. An integral part of the mechanism of many of these new methods of recovery is a miscible fluid displacement in which oil is displaced by a much less viscous materiai such as liquid propane. A numher of irlvestigators have explored the mechanics of miscible fluid displace-ment,'.2.1.'."." but in the experiments reported many of the important factors have been varied only over a limited range far removed from norma1 oilfield values. This paper presents the results of an experimental study of oil displacement by liquid propane at field rates from linear, natural-sandstone models of various sizes. Both horizontal and vertical flow tests were made. EXPERIMENTAL APPARATUS AND PROCEDURE Refined oils with viscosities varying over a wide range were displaced at several rates by liquid Propane from both horizontal and vertical flow systems. The behavior of the displacement was observed by propane-oil analyses of the effluent and, when possible, by differential pressure measurements along the cores. A schematic flow diagram of the apParatus used to conduct the experirents is shown in Fig. 1. The cores used in the tests were 9-ft lengths cut from natural consolidated sandstone and turned to the desired diameter. These were cast in steel tubing with a low melting point (160°F) alloy which expands on solidification. Flanges welded to the ends of the steel pipes permitted sealing the ends or butting one core to another. Pressure seals were maintained with O-rings. The cores were cleaned by flushing

By E. Marburg

Most ingots complete solidification vertically rather than transversely. This conclusion is based on complete solidification patterns of big-end-up and big-end-down ingots developed from dumped and split ingots. New mechanisms for segregation in ingots are proposed. Internal soundness in ingots is found to depend upon adequate width of vertical core. A LTHOUGH it has long been recognized that the A internal soundness of ingots is principally been recognizedthatthedependent on the process of solidification, knowledge of this process is still only fragmentary. The mechanisms causing the several types of segregation in ingots, which mechanisms are necessarily related to the solidification process, are not well understood. In absence of a better conception of the solidification process, it seems hardly surprising that mold design varies widely. Guiding principles for mold design are needed. At stake in the improvement of ingot quality are not only improved properties of steel but also appreciably higher yields of sound steel, which would considerably decrease manufacturing costs. In the present study, following a general description of the several types of segregation in ingots, Fig. 1, complete solidification patterns of a big-endup and a big-end-down ingot, including the zones of accelerated solidification, have been reconstructed. In both ingots, a core of vertical solidification extends from the base cone to the hot-top junction. Based on the finding that ingots complete solidification vertically rather than transversely, as has been previously assumed, new mechanisms for segregation in ingots are proposed. Internal soundness in ingots is found to depend upon the width of the vertical core, which in turn depends principally upon the width to height (w/h) ratio of the ingot. Solidification patterns of ingots are of three general types: 1—those in which vertical solidification does not reach the top, 2—those in which vertical solidification just reaches the top of the ingot, and 3—those in which vertical solidification reaches the top some time before transverse solidification would reach the middle of the ingot, so that a vertical core of definite width at the top of the ingot is developed. Axial defects vary characteristically with the solidification pattern. Examples of ingots of each type are presented. Dumped ingot data reported by Nelson' have been used in developing families of curves of transverse and vertical solidification, and in deriving the effect of the w/h ratio upon the solidification pattern. Photographs of many ingots split at Homestead and at Duquesne Works, United States Steel CO., as well as those published by the British Iron and Steel Institute,' have been studied and analyzed. In the interest of brevity, only typical ingots of each type or classification from the above sources have been reproduced. Segregation in Ingots Segregation in ingots falls into three principal classifications: 1—lamellar segregation, as revealed in sulphur prints (Figs. 2 and 3); 2—zone segregation, or broad variations in composition; and 3— interdendritic, or microsegregation. The last class, of minor importance, is not considered here. When liquid metal cools, according to the theory of differential or selective solidification,2 metal of relatively high purity selectively solidifies first. Liquid segregates (principally carbon, phosphorus,

Jan 1, 1954

By Sandford S. Cole

Manganese compounds occur in many mineral forms widely distributed throughout the crust of the earth. The most important of these commercially are the oxides which are usually found as irregular masses, but in some places (notably U.S.S.R.) occur as extensive beds of varying thickness and purity. The principal sources of ore have been U.S.S.R., Ghana (the Gold Coast of Africa), India, Union of South Africa, Belgian Congo, French Morocco, Cuba, Brazil, and Mexico. New developments of ore are being conducted in Brazil, British Guiana, French Equatorial Africa, and Northern Rhodesia. The production of the United States normally meets less than 10 pct of domestic manganese consumption. Manganese ore (35 pct or more Mn) is used principally by the ferrous metallurgy industry for production of manganese metal, ferromanganese, and other manganese alloys for use in production of steel ingots and castings. Some manganese is used in the nonferrous industry as an alloying element and cleanser in aluminum alloys, aluminum bronze, constantan, manganese bronze, Monel, Everdur, nickel-chromium resistance alloys, and nickel-silver. The metallurgical uses consume about 97 pct of the total manganese ore requirements of the United States. The balance goes principally for the manufacture of dry cells and for chemicals, with limited amounts for ceramic products, plastics, welding rods and varnish. The Materials Survey on Manganese, compiled in 1952 for Materials Office National Security Resources Board by the Bureau of Mines and Geological Survey, provides an excellent review of resources, reserves, specifications, uses, mining, beneficiation, metallurgical processes and deposits, and is worth referring to for greater details. Mineralogy and Geology The more common manganese minerals with typical characteristics are listed in Table 1 in order of importance. [ ]

Jan 1, 1960

By E. C. Burke, W. R. Hibbard

G. B. Craig (University of Toronto, Toronto, O,nt., Canada)—The advent of pyramidal slip at room temperatures in a magnesium crystal (M2,) and the very low value reported for the critical shear stress are puzzling. Table I1 shows the calculated values (approximate) for sin x cos I in this specimen if all the (10l) planes are considered. If So is the shear stress resolved in the direction of glide, on the glide plane, and U, is the stress operative in yield point tests, then: S,, — 325 (0.169) 55gpersqmm (approximately) for 1101: S,, = 325 (0.465) = 151 gpersqmm (approximately) for (0001): S,, — 325 (0.101) - 32.8 gpersqmm (approximately) Thus, we see the pyramidal plane in which the minimum shearing component operated. Barrett"' stated: "Experiments have repeatedly shown that, when there are several crystallographically equivalent slip systems in a crystal, the one having the greatest resolved shear stress will become active. ..." It does not appear to me that the measurements given are conclusive proof that pyramidal slip operated. E. C. Burke and W. R. Hibbard, Jr. (authors' reply) —Although the low value for the critical resolved shear stress for pyramidal slip may be puzzling, there does not appear to be any basis for questioning the validity of the measurements. Under the influence of constraints, slip systems having decidedly lower shearing components may become operative, e.g., "cross-slip" or the "forced glide" in magnesium reported by Bakarian. Since we believe that pyramidal slip occurred in the specimen because basal slip was inhibited, it is not too surprising to find an operative plane with a lower shear stress. -7 C. S. Barrett: Structure of Metals U94jl p. 2J6. New York. McGraw-Hill Book Co.

Jan 1, 1953

By S. E. Bretherton

Discussion of the paper of S. E. BRETHERTON, presented at. the San Francisco meeting, September, 1915, and printed in Bulletin No. 104, August, 1915, pp. 1595 to1599. ANTON EILERS, Brooklyn, N. Y. (communication to the Secretary*). While the advantages in the use of high-line siliceous slags in lead smelting which Mr. Bretherton discusses in this paper are obvious under certain economical conditions, he gives me credit for the introduction of such slags when it does not belong to me. It is true I did considerable experimental work, off and on, for the purpose of finding such slags, while at the Germania in 1877 and 1878, but I did not have occasion to introduce any such slags for regular work, because I had no ores which fitted the economical conditions for using high silica and high lime, except in isolated cases for very brief periods. On the contrary, the ores I had to treat were mostly very ferruginous and very low in silica, so that, economically, I was compelled to run nearly always on slags, which allowed me to use the abundant flux I had without cost. It was August Raht who first had occasion to establish and use for long periods a slag high in silica and line, and low in iron. This was when he was confronted with the task of smelting the. Horn-Silver ores at the smelting works at Franklin, Utah, with as little expenditure for fluxing material as possible. I was at that time in Leadville, Col., where, in the new works I had built, the Billings and Eilers smelters, I had occasion to use profitably many slags, but never anything as high in the earthy bases and in silica as Mr. Raht had to use.

Jan 12, 1915

By A. E. H. Bergmann

INTRODUCTION The Sachtleben Chemie GmbH in Duisburg, a subsidiary of the Metallgesellschaft AG, operates a new sulfuric acid plant that employs fluid bed roasting of pyrite concentrates. The plant produces about 300,000 tons per year of pyrite cinders from the fluid bed roasting unit. The cinder product consists of 58 percent iron and is about 80 percent by weight smaller than 50 microns. This cinder product was found to be a competitive source material for the cement industry as the iron-containing additive. However, the extreme fineness of the cinder and its dusting tendency were undesirable and an agglomerating technique became necessary. In order to keep the price of agglomerated pyrite-cinders at a competitive level, the agglomerating method must be chosen such a way the capital and operating costs are low. Initial experiments were carried out on a laboratory scale to make an appropriate choice of the agglomerating method. Major goals of agglomerating the cinders were to improve the transportation, storage, and proportioning and metering properties. Minimum specifications are put on the size, size distribution and shape of the product. Criterion for handling is that a minimum of minus one mm. fines are produced after several handlings, while for storage, it is also desirable for the agglomerated product to survive several months in open air. Thermal agglomeration processes such as sintering one known to produce excellent products, but are by far too expensive for our application. For the same reason, granulation, balling, and pelletizing tests with addition of organic binding agents, such as tylose, starch, sulfite wash, molasses, etc. were not continued. The costs for the binding agent was considerable, which is probably due to the high pore volume of our cinders (35 %). Furthermore, the pellets or granules

Jan 1, 1977

GEORGE F. KUNZ, New York, N. Y. (written discussion*).-We have been informed that the nickeliferous ores of Sudbury could furnish more palladium than the whole of the present world supply, together with a large amount of platinum. As the quantity of ore melted in Sudbury in 1916 totaled 1,521,689 tons, giving 80,010 tons of matte, and as the average of 3 years, up to 1915, are stated to show an average of 0.10 oz. of platinum and 0.15 oz. of palladium per ton of matte, this would indicate the presence of 12,000 oz. of palladium and 8000 oz. of platinum in the ore mined in 1916.1 Interest in the platinum situation is now more intense than it has ever been, and the great importance of this metal for many special uses is being increasingly appreciated. For munition manufacture, for chemical apparatus, in dentistry, and for jewelry, it has been and continues to be in great demand in spite of the phenomenal rise in its value. It is true that this has necessarily led to a search for substitutes, especially for dentistry and chemical uses, but while some of these have been found to answer the needs fairly well, for many 'other purposes platinum is still employed in spite of its great cost. As to the jewelry industry, the most public-spirited efforts have been made to restrict its use, and its employment in the manufacture of watchcases, purses, bracelets, and catches has been abandoned, gold being used in its place. The prime cause of the present shortage is, of course, the elimination of 'the Russian supply which, in normal times, constituted probably more than 90 per cent. of the world's production. This makes an intensive

Jan 4, 1918