Search Documents

By J. R. Stone, J. T. Roy

ASARC09s continuous tapper for lead blast furnace is described. Its use throughout the company's plants has resulted in higher production rates, lower labor costs, and better working conditions. It has also permitted wide latitude in blast pressures, as well as in charge and slag compositions. The practice of tapping a lead blast furnace has remained essentially unchanged for many years. In principle, it is a batch operation discharging the products from the continuous smelting of lead-bearing materials. As such, it imposes certain restrictions on the proper functioning of the smelting operation. First, it calls for a highly developed sense of timing, and a considerable amount of physical effort on the part of the operator. Dirty and hot working conditions, as well as the hazards of flying metal and slag, usually prevail. These conditions have resulted in higher labor costs, both in rate and in amount. Labor turnover has also been high. Secondly, rigid control of mechanical and metallurgical factors must be maintained. Frequent oxygen lancing of the tap hole is needed to permit tapping, thereby increasing operating costs. Rapid increases in smelting rate, plugged tap holes, or forgetfulness on the part of the operator may permit the molten material to rise above the tuyeies and freeze the furnace. Also, the operator will often blow out the tap hole after draining, filling the area with fume. Composition of charge also vitally affects the tapping. The type of lead-bearing material being smelted will naturally affect the smelting rate, and thus the frequency of tapping. The amounts and types of fluxing materials, which determine the ultimate fluidity of the slag, must be regidly controlled. Finally, the batch tapping of a continuous smelting operation of this type appears to be wrong in principle. The molten material drains into the crucible at the bottom of the furnace where it starts cooling immediately and continues to cool until tapped out. While keeping the lead molten is no particular problem, maintaining a fluid slag at all times is often difficult, and sometimes impossible. These factors all point to the desirability of a method for the continuous tapping of a lead blast furnace. The expected advantages would be more desirable working conditions, lower labor costs, increased production, and a much wider latitude in both blast pressure and charge composition. CONTINUOUS TAPPING Historical. A number of devices, e.g., mechanical tappers, siphons, and lead wells, have been tried in the past in attempting to effect continuous tapping. None proved to be entirely satisfactory for tapping lead and slag simultaneously. It was not until 1955, however, that ASARCO designed and put into operation a successful tapping unit at its East Helena, Mont. lead smelter. This unit is described in detail in U.S. Patent NO. 2,890,951. Continuous Tapping Unit—See Figs. 1 and 2. Fig. 1 is a schematic drawing of the unit in place, showing front and side views. The component parts are identified in the caption. Fig. 2 is an actual photograph, front view, of the tapping unit attached to the base of the blast furnace. Operation. The operation of the tapping unit is quite simple. Essentially it consists of a narrow tapping bay surrounding the furnace tap hole, with a deep notch in the front wall. When the blast furnace is started this notch is open down to the level of the tap hole. Starting the furnace may be accomplished in several ways but the most satisfactory method is to plug the tap hole with clay, permitting metal and slag to build up inside the furnace. Before the liquid reaches the tuyeres, the plug is removed and the furnace is drained to the settler. The blast is then stopped momentarily while the notch in the front wall of the tapping bay is dammed with chrome brick and plastic chrome ore. The blast is again started, and the height of the dam is adjusted so that the liquid in the bay will counterbalance the internal pressure of the furnace. When the desired level is reached the slag and metal will overflow to the settler. It should be noted that the molten material ,is not siphoned from the furnace and that the metal 'acts as a liquid valve controlling the flow of slag through the tap hole. During normal operations the tapping bay is filled primarily with lead, covered with a thin layer of slag. Thus, the heavier lead plays the major role in compensating for variations in furnace pressures. Due to the high specific gravity of lead, changes in the liquid level in the tapping bay will never exceed a few inches. For this reason it is seldom necessary to change the height of the dam due to minor variations in operating conditions. Some turbulence of the liquid in the bay is essential at all times. This indicates that the level of the

Jan 1, 1963

By Louis G. Bailey

This paper .reviews some of the key developments which have been made in the synthesis of the III-V compound semiconductors and the associated progress in obtaining high-quality material for device development. The history of the investigation of the semi-conducting properties of these materials has indicated the need for synthesis techniques capable of producing rnaterial of high chemical purity and physical perfection. The progress in the area is described, and the present status of quality of several compounds is discussed. In addition, recent studies of localized epitaxial deposition of GaAs into semi-insulating GaAs substvates for the development of arrays of devices ave reviewed. In conclusion, some important areas for future research and developrnent are discussed. INTEREST in III-V compounds as semiconductors dates back to the period 1950 to 1952, when Goryunova, Ioffe, and, in particular, Welker determined that 111-V compounds were structural analogs of the group IV elements carbon, silicon, germanium, and tin and that they were also semiconductors.'-3 Since that time interest in the properties of these materials has ex- panded rapidly. During 1953 and 1954, the first reports of rectification, photoconductivity, and optical absorption in these materials came from several investigators. In 1955, recombination radiation from samples of GaAs, InP, and GaSb was reported by ~raunstein .' This radiation was produced by injected minority carriers from point and large-area contacts. From 1955 to 1960, efforts increased on preparing large, pure specimens of these materials for the study of basic physical phenomena and device exploration. By 1960, materials preparation and the understanding of the physics of some of the materials had advanced to where some very interesting and potentially useful phenomena came under study. The first observation of electric-field-induced changes in the optical absorption edge (Franz -Keldysh effect) of 111-V compounds was reported for GaAs by Moss in 1961.' In 1962 the study of recombination radiation advanced rapidly. Keyes and Quist6 and Pankove and Berkey-heiser7 reported high radiative efficientices obtained from recombination, and then the first injection electroluminescent lasers in GaAs were announced by Hall ef al.,' by Nathan et al.,O and by Quist ef al.,'O and in Ga(As, P) alloys by Holonyak and Bevacqua." Hil-sum has reviewed the early work leading to the first observations of laser action in GaAS." Recombination processes in GaAs, Gap, and the other 111-V com-

Jan 1, 1968

By E. Hornbogen

The deformation mechanisms of a iron-phosphorus alloys were compared at 20oand —196°C. Alloying with phosphorus increases the resistance to slip, but has little effect on the resistance to twinning. The stress for onset of twinning is nearly independent of temperature, but there is an increasing tendency for cleavage along (112) twin boundaries with decreasing temperature and increasing phosphorus content. FIVE iron-phosphorus alloys and one high-purity iron (0.004 pct C, 0.004 pct N, 0.05 pct O) were vacuum melted and cast, then homogenized for 6 hr at 1100oC and water-quenched. Single crystals were cleaved from the coarse grains produced in this manner. The hardness was measured* on polished (100) surfaces of the crystals at 20" and -196°C. Laue back-reflection patterns indicated a deviation of not more than 3 deg from coincidence of the {100} plane with the surface. The deformation mechanisms were studied by relief effects on the polished surfaces. Yield points in compression (0.5 pct offset) were measured with polycrystalline material. At 20°C the addition of phosphorus to a iron leads to a change from slip to twinning as the main deformation mechanism, Figs. 1(a), (b). Between 2 and 4 at. pct P slip and twinning occur simultaneously. In alloys with more than 4 at. pct P twinning is the main deformation mechanism and slip was observed only in the neighborhood of twin intersections. All cracks at 20oC were on (100) planes, some initiated by twins.' From measurements made at-196oC, hardness and yield points of all the alloys were nearly constant and the same as the hardness of high phosphorus alloys that deformed by twinning at 20°C, Figs. 2 and 3. In the high-purity iron, plastic deformation at -196°C occurred by both slip and twinning, but deformation in the iron-phosphorus alloys appeared to be entirely by twinning. In the high phosphorus alloys a large number of cracks formed along the (112) twin boundaries and at intersections of twins, in addition to the (100) cleavage, Fig. 1(c). DISCUSSION In , iron, plastic deformation can occur either by slip or by twinning, depending upon composition,

Jan 1, 1961

By James M. Link

Slurry transport of industrial minerals has proven to be practical, economical, and efficient. Industrial minerals currently being pumped for long distances include cement, clay, phosphate, sand, and various waste product from industrial mineral processing operations. This paper will touch upon the basic theory of hydraulic transport of solids and then consider the economic and engineering considerations upon which construction and operation of such a line would be based. Where possible, actual cost data will be presented.

Jan 1, 1974

LIST OF THE MEETINGS OF THE INSTITUTE AND THEIR LOCALITIES FROM ITS ORGANIZATION TO OCTOBER, 1904 Transactions Number Place Date Vol Page 1 Wilkes-Barre, Pa May, ?71 1 3 2 Bethlehem, Pa August, ?71 1 10 3 Troy, N Y November, ?71 1 13 4 Philadelphia, Pa February, ?72 1 17 5 New York, N Y May, ?72 1 20 6 Pittsburg, Pa October, ?72 1 25 7 Boston, Mass February, ?73 1 28 8 Philadelphia, Pa May, ?73 2 3 9 Easton, Pa October, ?73 2 7 10 New York, N Y February, ?74 211 11 St Louis, Mo May, ?74 3 3 12 Hazleton, Pa October, ?74 3 8 13 New Haven, Conn February, ?75 3 15 14 Dover, N J May, ?75 4 3 15 Cleveland, 0 October, ?75 4 9 16 Washington, D C February, ?76 4 18 17 Philadelphia, Pat June, ?76, 5 3 18 Philadelphia, Pa October, ?76 5 9 19 New York, N Y February, ?77 5 27 20 Wilkes-Barre, Pa May, ?77 6 3 21 Amenia, N Y October, ?77 6 10 22 Philadelphia, Pa. May, ?78 6 18 23 Chattanooga, Tenn May ?78 7 3 24 Lake George, N.Y. Oct. ?78 7 25 Baltimore, Md. Feb. ?79 7 26 Pittsburgh Pa, May ?79 8

Jan 1, 1923

LIST OF THE MEETINGS OF THE INSTITUTE AND THEIR LOCALITIES FROM ITS ORGANIZATION TO OCTOBER, 1904 Transactions Number Place Date Vol Page 1 Wilkes-Barre, Pa May, ?71 1 3 2 Bethlehem, Pa August, ?71 1 10 3 Troy, N Y November, ?71 1 13 4 Philadelphia, Pa February, ?72 1 17 5 New York, N Y May, ?72 1 20 6 Pittsburg, Pa October, ?72 1 25 7 Boston, Mass February, ?73 1 28 8 Philadelphia, Pa May, ?73 2 3 9 Easton, Pa October, ?73 2 7 10 New York, N Y February, ?74 211 11 St Louis, Mo May, ?74 3 3 12 Hazleton, Pa October, ?74 3 8 13 New Haven, Conn February, ?75 3 15 14 Dover, N J May, ?75 4 3 15 Cleveland, 0 October, ?75 4 9 16 Washington, D C February, ?76 4 18 17 Philadelphia, Pat June, ?76, 5 3 18 Philadelphia, Pa October, ?76 5 9 19 New York, N Y February, ?77 5 27 20 Wilkes-Barre, Pa May, ?77 6 3 21 Amenia, N Y October, ?77 6 10 22 Philadelphia, Pa. May, ?78 6 18 23 Chattanooga, Tenn May ?78 7 3 24 Lake George, N.Y. Oct. ?78 7 25 Baltimore, Md. Feb. ?79 7 26 Pittsburgh Pa, May ?79 8 28 Montreal, Canada Sept, ?79 8

Jan 1, 1923

By D. M. Clippinger, J. J. Eidel, J. E. Frost

At Ithaca Peak, one of three peaks situated on Duval Corporation's Mineral Park property, a 'Single pulse of quartz monzonite magma intruded the isoclinally folded Precambrian Cerbat complex consisting of schist, quartzfeldspar gneiss, and amphibolite. The magma reacted with the Precambrian rocks, yielding a quartz-diorite rim. As the magma crystallized within the rim, it produced, progressing in'ward, annular bodies of quartz monzonite porphyry, quartz porphyry, and a distinctive quartz porphyry containing abundant podiform, tabular, and irregular quartz masses. These quartz masses are spatially associated with discontinuous crenulate and tabular quartz veinlets. Following crystallization, the Ithaca Peak stock and part of the surrounding Cerbat complex were fractured, producing a stockwork of predominantly northwest and northeast-trending fractures. The stockwork was then mineralized during a period of decreasing temperature by: ( 1) quartz-pyritechalcopyrite veinlets without distinct selvages and with distinct alteration envelopes in which orthoclase was altered to quartz and sericite; (2) quartz-pyrite-chalcopyrite veins and veinlets with distinct selvages and without distinct alteration envelopes; and (3) pyrite-chalcopyrite- galena-sphalerite veins. The Ithaca Peak stock was pervasively sericitized or argillized. The Mineral Park property is surrounded by a zone of propylitization Alteration and mineralization are coextensive in space and were, at least in part, coincident in time. The Mineral Park property possibly was elevated and exposed twice prior to its present exposure. The protore has been enriched by a factor of three. The Ithaca Peak supergene ore body is conformable with present topography and lies above the present water table. The shape of the ore body was controlled by erosion and oxidation of the previously enriched mineralization. Hematite, goethite, and jarosite present at the surface indicate a high primary pyrite environment, but it is possible to recognize that a small proportion of veins and veinlets contained greater amounts of chalcocite and chalcopyrite than pyrite. The igneous facies on Ithaca Peak are the products of differentiation within a solidifying rim according to Bowen's Reaction series. The innermost facies contain more quartz and orthoclase than the outer facies. Late magmatic quartz in the case of Ithaca Peak contains small amounts of pyrite and molybdenite. It is suggested that this quartz-sulfide mineralization, may also have been the product of differentiation the product of differentiation, may indicate that the later hydrothermal mineralization may also have been the product of differentiation.

Jan 1, 1968

R. F. MCELVENNY.- Over 20 years ago I went back East on a little tour of copper companies to see how copper was handled and fabricated, and I met a Mr. Bassett who took me through the Waterbury branche of the American Brass Co. I have not seen this gentleman for 20 years, but I have a letter from him that I would like to read to you. 'The American Brass Co. Waterbury, Conn. May 19, 1930. To the-Salt Lake City Conference on Reverberatory Smelting Practice: Through the courtesy of Mr. Scott Turner, Director of the U. S. Bureau of Mines, Mr. G. L. Oldright has been temporarily released from his regular duties to act as your secretary. We have asked him and Mr. McElvenny to make the necessary preliminary arrangements and to present to you at the opening session the greetings of the officers and' directors of the Institute. I am very glad that it has been possible for you to come together under the auspices of the Institute and that the acceptance of our invitation has been so very unanimous. Such an acceptance of the invitation to this meeting indicates your interest in getting together for an exchange of technical data and ideas. We anticipate that this meeting will be of real service to the smelting industry through your open discussion and exchange of ideas, and we sincerely hope that you will form an organization which will arrange for future meetings of a similar nature. While it probably may not be desirable to. distribute the minutes of this conference except to the members who take part in it, we hope that later the Institute publications may be enriched by such matter as you think it desirable to have published; and also, that some of you may be able to offer technical papers for the Institute publications. I hope that you will find a permanent organization desirable and trust that it will be possible for you to form such an organization so that conferences may be regularly called. We hope that you can make use of the Institute organization and that we can be of real service to your industry. With best wishes for your success in this undertaking, I am Most cordially yours, W. H. Bassett, President.

Jan 1, 1930

By L. P. Durham

DuRing the early mine development period, 1929 and the first part of 1930, a 300-ton pilot-plant concentrator was built at Nkana mine of the Rhokana Corporation, Northern Rhodesia. This plant operated from May 26, 1930 until Oct. 26, 1931, treating 101,080 tons of Nkana ores and producing 4372 tons of concentrate. The plant was built, primarily, as a test unit to determine the grinding characteristics, floatability, etc. of the Nkana ores and other ores of the Rhodesian copper belt and to supply sufficient data on which to base the design of a 5000-ton concentrating plant at Nkana mine. The test unit operated wholly on development ores and no attempt was made to grade or select the ores from any section of the mine. The average assays for the 17 months of operation are given in Table 1. The first ground was broken for the 5000-ton concentrator during June, 1930, and the construction of the plant was completed in November, 1931. The plant started on Dec. 10 and has operated continuously since that date: The whole of the concentrating plant is compact and closely connected, yet with sufficient space for expansion of all sections up to 20,000 to 25,000 tons per day capacity. Mining operations are carried on along a length of about four miles on the easterly limb of the Nkana syncline. This length includes the North orebody, from which all production has thus far originated, and the Mindola orebody, now being developed for production. The ore-bearing measures in the North orebody are leached for some 75 ft. below the surface; the oxidized zone varies in vertical extent from 100 to 150 ft. Practically all the ore below the 200-ft. level is sufficiently

Jan 1, 1935

By Paul W. Zimmer, Carl E. Dutton

Iron ore in the Menominee district is mined from two iron-formations of middle Precambrian age. The older formation is present in the northeastern part; is composed mainly of hematite, magnetite, quartz, and minor silicates; and contains about 34 per cent iron. The rock has been so coarsened by meta- morphism that concentration of magnetite and hematite is feasib!e, and pellets containing more than 60 per cent iron are being produced. The older formation is also present in the southeastern part where it has 1:een only slightly metamorphosed. Ore containing more than 50 per cent iron was formerly mined from local residual concentrations of iron oxides from which silica had been sufficiently leached, or replaced by iron oxide, or affected by combinations of these processes. The younger iron-formation occurs in the western part of the district and, if unaltered, is interlayered siderite and chert. The ore in this area also contains more than 50 per cent iron and formed as local residual concentrations but in two stages. The siderite was converted to iron oxides (hematite and "limonite"), and silica was contemporaneously or subsequently removed by leaching, or replacement, or combinations of these processes.

Jan 1, 1968

Eight members of the Board, the Secretary of the Institute, and eleven guests were present. Vice-president Henry S. Drinker presided. The President was authorized to appoint delegates to a meeting, on May 16, of the League to Enforce Peace. The Joint Conference Committee reported that the American Institute of Metals had accepted the invitation to form the Institute of Metals Division of this Institute. The Committee on Publications of the Institute of Metals was added to the Committee on Publications of the A. I. M. E. Exchange of one volume of Transactions of the A. I. M. E. at reduced price to members of the British Institute of Metals was authorized, in return for the reduced price given to our Institute of Metals Division on the annual proceedings of the British Institute.

Jan 6, 1918

Meeting of Mar. 26, 1915.-The following Committee on Nominations was appointed: Fred W. Bradley, Chairman; James F. Kemp, Past President; Frank M. Smith, Chairman Montana Section; R. C. Gemmell, Chairman Utah Section; Frank A. Ross, Chairman Columbia Section; Louis S. Cates, Arthur Thacher. The Committee on Precious and Base Metals and the Committee on . Coal and Coke were appointed, the personnel of which is shown in another part of this Bulletin. The President was authorized to appoint a Committee on Welfare with J. Parke Channing as Chairman. W. P. Cutter, Librarian of the United Engineering Societies' Library, was appointed a representative of the Institute on-the Committee oh Classification of Engineering Knowledge to co-operate with similar committees of other engineering societies. A vote of thanks was extended-to Edward B. Sturgis for his excellent work in arranging for the Annual Dinner. in February, of this year. The suns of $57.30 was appropriated to the New' York Section. It was resolved that in response to the courteous invitation from 36 members of the Institute in Arizona and the neighborhood, the 1916 summer meeting of the Institute be held in Arizona.

Jan 5, 1915

By R. W. Raymond

Edward Cooper was born in New York City, Oct. 26, 1824. His father, Peter Cooper, to say nothing of manifold reasoils for fame as an inventor and philanthropist, deserves to be remembered as a pioneer in the establishment .of public schools ; and it is not surprising that. he sent his son to one of the democratic institutions in which he was himself so ardently interested. From the public school Edward Cooper went to Columbia College, where he made the acquaintance of Abram S. Hewitt, who was first his tutor, afterwards his traveling companion, brother-in-law, business partner and life-long friend.' For twenty years I was the consulting engineer of the firm of Cooper & Hewitt, and also connected with the work of the Cooper Union, in which they were both deeply interested and faithfully active. On the basis of the intimate knowledge thus gained, I venture an estimate of Edward Cooper's character and career which, if not fully comprehensive, may facilitate a juster estimate than would be reached by the student of those data which the modesty of the man permitted to be placed upon public record.

Jan 1, 1907

By B. N. Das, P. A. Beck

THE o phases have a complex tetragonal structure with Lo/ao = 0.52 and 30 atoms per unit cell.1 A large number of such phases are now known to occur in various binary systems of the transition elements and they exhibit the following typical features: 2,3 The composition of binary o phases is variable, ranging from approximately A4B to ABI. With only a few exceptions, in the o phases the A-ele-ment comes from the V- or Cr- group of the periodic table, while the B-elements are from the Mn-, Fe-, Co-, or Ni- group. In the first long period the corresponding o phases of the V- and Cr-series have approximately the same compositions. However, as the B-element changes from Mn to Fe to Co to Ni, the mean composition shifts monotonously toward higher A-contents.2-4 For example, if the mean compositions of the various o phases with vanadium are compared with each other, the composition shift mentioned above becomes plainly visible: V 30Mn0 80 Vo.45Feo..,, Vo .,Coo. 45 and Vo.5Nio.3. Similiar composition shifts, although not the same composition values, were observed in u phases formed by second and by third long-period transition elements.3'4 This behavior, very characteristic of o phases, is in rather sharp contrast to the usually quite well-behaved stoichi-ometry of the Laves phases. In the latter, the AB2 stoichiometry predominates, with A the large atom and B the small atom.= The p phase occurs in the four binary systems of Mo or W with Fe or Co. On the basis of their crystal structure determination, Arnfelt and westgren6 ascribed to the p phase in the Co-W system the ideal composition W,Co7. Since all four binary pphases have nearly the same composition, it would seem quite plausible that some definite stoichiometry such as A6B7, might be characteristic of this phase, as AB2 is of the Laves phases. On the other hand, it has been noted,7 that the phases occur at average electron concentrations near to those at which the various cr phases are found. Also, it has been pointed out by Shoemaker and associates8 that structurally the a phases and the p phases are somewhat related to each other; both of these structures may be described in terms of suitable stackings of quasi-hexagonal layers'of atoms. By studying a suitably chosen ter- nary phase diagram, one might expect to be able to find out which one of the two conditions, the analogy with the o phase or the constant ratio between the number of large atoms and the number of small atoms in effect governs the behavior of the p phase. Several isothermal sections of ternary systems containing o phases have been investigated. In all cases where two binary o phases occur, these were found to be connected b a more or less straight ternary o phase field.7' '10 Such elongated o phase fields were also found in ternary systems in which only one of the limiting binaries is known to contain o phase. In this manner a latent o forming tendency could be detected and the virtual composition of a "binary o phase", which does not actually occur as such was approximately determined by extrapolation. The behavior of the phases, including their composition shift, is analogous to that of the classical electron compounds, as described by Hume-Rothery.11 In order to decide whether the p phase is essentially a "size compound" like the Laves phases, where a fixed stoichiometric ratio is quite generally maintained between the "large atoms" and the "small atoms", or whether the p phase is typically an "electron compound" in the same sense as ois, it was decided to investigate an isothermal section of the Mo-Mn-Co system. The Mo-Co system12 and the Mo-Mn system13 each are known to have a binary o phase. It could be therefore expected that a ternary o phase field will connect these two binary cr-phase fields. The p phase is known to occur in the Mo-Co system. If the p phase should turn out to form an elongated phase field extending deep into the ternary system, the following considerations mighto apply. The atomic radius of manganese (1.314for C.N.12) is between the va,lues for Mo (1.40Afor C.N.12) and for Co (1.26Afor C.N.12). If it is assumed that p is a "size compound", and that Mn is substituting for the smaller Co atoms in the p-structure in the ternary system, the y-phase field might be expected to extend parallel to the Mn-Co binary line. If Mn is substituting for the large Mo atoms in the p-structure, the p-phase field may be expected to extend parallel to the Mn-Mo binary line. On the other hand, if the p-phase turns out to be an "electron compound" like o, the ternary p-phase field should extend parallel to the ternary o -phase field connecting (Mo,Mn)owith (Mo, Co) a

Jan 1, 1961

By Helmut Thielsch

In recent years an ever increasing amount of interest has been directed toward research studying the principles and various applications of sonic and supersonic waves. Though still in their early stages of practical development, sonic vibrations are already used in the emulsifi-cation and degasification of liquids. Metals exposed to sonic or ultrasonic vibrations while solidifying show a considerable amount of grain refinement. Often sound waves are applied instead of radiography to test engineering materials for internal cracks and flaws.' In the field of pure research these waves are used in dispersion and also in coagulation of particles or liquids in gaseous or, under certain conditions, in other liquid systems. In the settling and thickening of slurries considerable time is necessary to compress the solid particles and to squeeze out the liquid to obtain as low a dilution (liquid to solid ratio) as possible. Various methods have been developed to increase the amount of coagulation of the very fine solids (colloidal or semicolloidal) and to shorten the over-all time. The addition of small amounts of electrolytes and the warming of the suspension represent merely the more important techniques. Some of the effects of supersonic vibrations have been reported previously. From preliminary studies, therefore, it was hoped that by application of sonic vibrations it would be possible to reduce the time required to thicken such materials to a specific dilution, as well as to thicken to lower ultimate dilutions than could be obtained by quiescent settling alone. By increasing the volume thickened per unit time—i.e., improving the plant efficiency— great savings in equipment and time would be obtained for industrial processes. Also, faster settling rates should result if coagulation of particles could be increased. Experiments have been conducted for a period of several months in the Allis-Chalmers laboratory to study the effect of sonic vibrations on settling of particles of different sizes and concentrations. Apparatus The sedimentation apparatus used in these experiments is illustrated in Figs. I and 2. The essential features are the stationary field coil and the movable voice coil. Both windings are placed around a solid iron core. A leather diaphragm connected to the steel frame holds the voice coil in place. A brass rod is fastened to the voice coil with a metal disk connected to the other end. This disk is sealed to the lucite cylinder with a flexible rubber diaphragm. The lucite tube is 17 in. long; its inner diameter is 2½ in. and the wall thickness is ¼ in. The tube is calibrated on the outside in 10 c.c. divisions for a total of 1000 cubic centimeters.

Jan 1, 1947

By Helmut Thielsch

In recent years an ever increasing amount of interest has been directed toward research studying the principles and various applications of sonic and supersonic waves. Though still in their early stages of practical development, sonic vibrations are already used in the emulsifi-cation and degasification of liquids. Metals exposed to sonic or ultrasonic vibrations while solidifying show a considerable amount of grain refinement. Often sound waves are applied instead of radiography to test engineering materials for internal cracks and flaws.' In the field of pure research these waves are used in dispersion and also in coagulation of particles or liquids in gaseous or, under certain conditions, in other liquid systems. In the settling and thickening of slurries considerable time is necessary to compress the solid particles and to squeeze out the liquid to obtain as low a dilution (liquid to solid ratio) as possible. Various methods have been developed to increase the amount of coagulation of the very fine solids (colloidal or semicolloidal) and to shorten the over-all time. The addition of small amounts of electrolytes and the warming of the suspension represent merely the more important techniques. Some of the effects of supersonic vibrations have been reported previously. From preliminary studies, therefore, it was hoped that by application of sonic vibrations it would be possible to reduce the time required to thicken such materials to a specific dilution, as well as to thicken to lower ultimate dilutions than could be obtained by quiescent settling alone. By increasing the volume thickened per unit time—i.e., improving the plant efficiency— great savings in equipment and time would be obtained for industrial processes. Also, faster settling rates should result if coagulation of particles could be increased. Experiments have been conducted for a period of several months in the Allis-Chalmers laboratory to study the effect of sonic vibrations on settling of particles of different sizes and concentrations. Apparatus The sedimentation apparatus used in these experiments is illustrated in Figs. I and 2. The essential features are the stationary field coil and the movable voice coil. Both windings are placed around a solid iron core. A leather diaphragm connected to the steel frame holds the voice coil in place. A brass rod is fastened to the voice coil with a metal disk connected to the other end. This disk is sealed to the lucite cylinder with a flexible rubber diaphragm. The lucite tube is 17 in. long; its inner diameter is 2½ in. and the wall thickness is ¼ in. The tube is calibrated on the outside in 10 c.c. divisions for a total of 1000 cubic centimeters.

Jan 1, 1947

By W. Hurst

The authors of this paper, in substituting values in a material balance equation associated with a gas reserve and a water drive, cannot find sustainment of what the gas in place should be; therefore, their conclusion is that this type of problem dealing with gas reservoirs is insoluble. They have introduced the word, "cybernetics," based on the work of Norbert Wiener, that further extends this line of reasoning, namely, to the effect that the system is a "black box", and that the gas reservoir and aquifer can take on infinite aspects 'based upon their past performance, to quote the authors. The inference is that this black box is an unknown. which permits in computer programming to subscribe as many variables as possible to observe by adjustment of one to another those combinations of conditions that fit field behavior. This may satisfy those in this discipline whose dedication is to programming, but to the others this is a comparison to the rationalization of the combinational results of the throwing of dice—a probability procedure. In reservoir engineering we are more direct. We learn from the examination of individual we'll and field data exactly what is in this black box. I now come to the impasse that has confronted these authors in their machine calculations. In this I have reproduced from their own production data (Tables 1 and 2 of their paper) pressure vs cumulative gas produced. shown as Figs. D-1 through D-5. A perusal of any of these five plots, for the corresponding fields in the Po Valley, shows the straight-line relation of pressure vs gas produced, evidencing pressure depletion. The point I make is that in their fundamental production data, there is no variance from a straight line that can support a water drive.

By AIME AIME

LOCAL COMMITTEES. EXECUTIVE.-W. A. Lathrop, Chairman; R. V. Norris, Secretary; S. D. Warriner, Treasurer; Irving A.. Stearns, W. J. Richards, H. S. Drinker, C. D. Simpson. GENERAL RECEPTION.-Irving A. Stearns, Chairman. Archibald, James, Jr., Pottsville. Lawall, E. H., Wilkes-Barre. Ashley, H. H., Wilkes-Barre. Lentz, W. 0., Mauch Chunk. Ayres, WV. S., Hazleton. Lewis, Albert, Bear Creek. Beard, J. T., Scranton. Loomis, W. H., Jeddo. Bridgman, J. C., Wilkes-Barre. Markle, Alvan, Hazleton. Bunting, Douglas, Wilkes-Barre. Markle, John, Jeddo. Chase, F. M., Wilkes-Barre. Neale, J. B., Minersville. Coroner, Eli T., Scranton. Norris, R. V., Wilkes-Barre. Cote, E. B., Jr., Drifton. Oliver, Paul A., Oliver's Mills. Davies, W. H., Hazleton. Owens, W. D., Pittston. Davis, H. G., Dorranceton. Pardee, 1. P., Hazleton. Dodge, W. F., Wilkes-Barre. Quin, R. A., Wilkes-Barre.

Jul 1, 1911

By F. A. Olson, S. L. Pohlman

A unique method of measuring weight loss as a function 3 of time, with a sensitivity of 10-5 grams, while leaching copper minerals with a flowing acid leach solution has been developed. Kinetic results obtained coupled with visual and microprobe analyses show topochemical reaction for the leaching of chrysocolla with sulfuric acid. The kinetics follow a shrinking core model and show ion diffusion through a product layer, chemical reaction at the unreacted core interface and mass transfer through the boundary layer as being important.

Jan 1, 1974

By J. B. Dyess

TARNISH films on some of the common metals (particularly on copper and silver) have been of much scientific and commercial concern for a long time, but before the development of the electrical method1 of measuring film thicknesses there was no satisfactory quantitative approach by which to study the separate parts of these complex films. This method has been adapted to the measurement of duplex (cuprous-cupric) oxide films on copper .2 In the present work it has been used to measure tarnish films on copper when they were mixtures of cuprous oxide and cuprous sulphide, and also when they contained cuprous oxide, cupric oxide and cuprous sulphide, each component part being measured at a different potential value. Oxide-coated copper specimens, prepared by heating copper in air at chosen temperatures for given periods, were exposed to moist hydrogen. sulphide in air to form the various oxide-sulphide films studied. The comparative resistances afforded by (1) different thicknesses of oxide films, and also (2) equal thicknesses of oxide and sulphide films, against severe attacks of hydrogen sulphide were measured. The electrical method requires that the time be observed for the cathodic reduction of each part of the film substance, and these respective time values multiplied by the constant current give the corresponding quantities of electricity expended. Then each millicoulomb per square centimeter represents a film thickness of T= MX10 8 2D X 96,494 X 103 (a) where M is weight of oxide (or sulphide) giving one gram-atom of oxygen (or sulphur) for cathodic reduction, D is density of the oxide (or sulphide) and t is the thickness in Angström units per millicoulomb per square centimeter. The value of t for cuprous sulphide (cubical) is 14.27, and is obtained by substituting 5.78 for D and 159.20 for M in equation a. Previous values2 of t for cuprous and cupric oxides (12.36 and 6.39, respectively) were used in the present work.

Jan 1, 1939