Search Documents

By Albert J. Phillips

LEAD is an inexpensive metal produced and consumed in large quantities with certain chemical and physical properties that permit handling the molten metal in bulk. These properties are its low melting point, resistance to oxidation, and its negligible solvent action on iron and steel. Thus, lead is almost always melted in large iron or steel kettles, heated from beneath, and is seldom melted in either directly or indirectly fired furnaces or electric induction or arc furnaces. Even with a modest operation a kettle holding 2 or 3 tons is employed, and the size will range up to 215 tons in the large lead refineries. The methods of handling tin and its alloys are essentially the same as for lead because of the similarity in melting point and resistance to oxidation, although because of the cost of the metal the scale is more modest. In melting lead and its alloys preliminary to a casting operation it is seldom that the melting unit is completely drained of its contents. The usual procedure is to continuously charge solid metal and continuously remove small amounts of liquid metal, so that the kettle is maintained essentially full at all times. For type metals, linotype machines usually employ automatic means of adding the solid alloy to the melting pot in proportion to the removal of the liquid metal in casting slugs of type. In the casting of grids for storage batteries, frequently automatic means of charging solid metal in direct proportion to the consumption of liquid metal in the casting is used. In the manufacture of bearing alloys, new alloy is charged in direct proportion to the consumption of metal in the bearings being cast, so that at no time does the level of the metal in the melting pot lower to any great extent. Even in the manufacture of bulky commodities such as pipe, cable. sheathing, and slabs for rolled sheet, it is the practice to employ a melting kettle of several times the capacity of the casting being made. A substantial level of liquid metal in the melting kettle is thus maintained even after the casting is poured and the original metal level is quickly restored by promptly charging new metal, even though there is no immediate need to proceed with additional casting. This procedure is permissible because the amount of fuel consumed in keeping the lead molten and immediately available for use is negligibly small and the cost is more than offset by the convenience. However, this convenient procedure necessitates study and control of certain properties of lead and tin alloys that are not of serious consequence in most other alloys and for that reason are not well known. These properties are "drossing rates" and "melting segregation." DROSSING RATE Users of lead long ago observed that the rate of dross formation on the surface of the lead in their kettles or pots varied greatly from time to time. This was particularly common in places where both antimonial lead alloys and commercially pure lead were being handled.

Jan 1, 1946

THE discussion at the annual meeting of the paper on "Devices for Detecting Dangerous Gases in Mine Air" (published in. MINING AND METAL-LURGY, February 1, 1927, p. 69) was prefaced by the following description of a new portable methane indi-cator, presented by D. C. Ashmead: Two comparatively recent disasters in Utah are directly responsible for the perfection of the new methane detector. The first of these occurred on May 1, 1900, when 200 work-men lost their lives. The second disaster did not occur for more than two decades, when, on March 8, 1924, at the Castle Gate Mine No. 2, 172 workmen were killed. A dis-sembled safety lamp was later found at the seat of the ex-plosion. This indicated, as a possible cause, that the safety lamp had gone out and the fire boss had tried to relight it. These two disasters brought, the mine operators of the State of Utah to the concentrated attempt to end the loss of life through mine explosions. The Governor of the State appointed a committee, known as the Utah Mine Op-erators Committee, to study the phases of the problem, and this Committee in turn enlisted scientists all over the country in cooperative research. One group, under the direction of E. K. Judd, of the Union Carbide and Carbon Research Laboratories, of Long Island City, New York, concentrated its efforts on develop-ing a methane detector which would be completely ade-quate. This is now successful, since in laboratory as well as actual coal-mine tests the apparatus has instantaneously and accurately detected the presence of extremely small amounts of methane.

Jan 3, 1927

The following is an incomplete list of members and guests who called at Institute headquarters during the period Oct. 10, 1919, to Nov. 10,1919. Carl A. Allen, Salt Lake City, Utah. W. G. Mitchell, Montreal, Canada. M. M. Altmayer, Paris. Henry S. Munroe, Litchfield, Conn. A. E. Bellis, Major Ord., Springfield J. S. Negru, New York, N. Y. Armory, Springfield, Mass. Edmund Newton, New York, N. Y. R. S. Botsford, New York, N. Y. A. W. Newberry, Cleveland, Ohio. Henry S. Burnholz, Monterrey, Mexico. C. C. O'Harra, Rapid City, S. D. D. E. A. Charlton, New York, N. Y. Fred S. Porter, Philadelphia, Pa. C. C. Colburn, Denver, Colo. Donald A. Powell, Columbus, Ohio. C. V. Corless, Coniston, Ontario. Thomas T. Read, Washington, D. C. I. N. Daily, Seattle, Wash., W. L. Remick, Chrome, N. J. E. V. Daveler, Butte, Mont: Hallet R. Robbins, San Francisco, Calif. John Davis, Fairbanks, Alaska.' Milnor Roberts, University Station, E. W. Engelmann, Salt Lake City, Utah. Seattle, Wash. M. E. Erdofy, New York N. Y. Thos. S. Roberts, Lakehurst Proving W. F. Ferrier, Toronto, Canada. Grounds, N. J. H. A. Fisher, Pittsburgh, Pa. George B. Rodgers, Dobbs Ferry, N. Y. Walter Fitch, Sr., Eureka, Utah. John C. Rogers, Copper Cliff, Ontario. C. D. Grier, New York, N. Y. Joseph L. Rosenmiller, Bethlehem, Pa. A. Hibbert, London. . C. J. Saville, Portland, New South Wales. John E. Hodge, Minneapolis, Minn. W. A. Scheuch, New Jersey. W. E. Hopper, Newark, N. J. S. B. Shutts, Lynchburg, Va. M. R. Hull, McGill, Nev. E. W. Smith, U. S. Army. A. W. Ibbett, Trinidad, B. W. I. S. J. Speak, London. A. O. Ihlseng, Joplin, Mo. John. B. Stewart, Santiago de Cuba, Sherwin F. Kelly, Lawrence, Kans. Cuba. R. G. Knickerbocker, Logansport, Ind. S. A. Taylor, Pittsburgh, Pa. .M. H. Kuryla, Eureka Colo. Karl Thomas,' New York, N. Y. F. G. Lasier, Detroit, Mich. F. L. Torres, Eureka, Nev. David Lasuer, Elizabeth, N. J. Henry Traphagen, Toledo, .Ohio: H. H. Lauer, Allentown, Pa. W. D. Van Doren, Ottawa, Canada. J. Whitney Lewis, Care First Nat'l Bank, J. A. Vernon, Newport, R. I. Tulsa Okla James Wilding, San Francisco, Calif. James W. Love, Knoxville, Tenn. D. J. Williams, Butte, Mont. Dorsey A. Lyon, Washington, D. C. Harry J. Wolf, New York, N. Y. M. E. Martiner, Boston, Mass.. Dwight E. Woodbridge, Duluth, Minn. Benj. L. Miller, Bethlehem, Pa. Percy E. Wrighn, Seattle, Wash. W. G. Miller, Toronto, Canada. F. Yamada, Tokyo, Japan.

Jan 12, 1919

By Paul H. Johnson

Chemical mining may be defined as the use of chemicals in extracting metal values from in situ broken or unbroken ores within a mine. The present means for the generation and regeneration of sulfuric acid or sulfuric-ferric sulfate solutions are inadequate for most applications. This report describes a pressure oxidation process for the generation and regeneration of these solutions from pyrites and spent iron sulfate leach liquors. While recent mining developments such as solution injection, caving, and conventional and nuclear blasting, have provided new and better means for the per-colation of leach solutions through rock masses, little has been done to reduce cost and improve the quality of the leach solutions that are required. A leach solution for chemical mining should meet certain requirements. It should be 1) inexpensive on either a small or large tonnage basis, 2) capable of selectively leaching the desired ore minerals contained in a particular ore, 3) of the proper strength or quality to do the job of leaching in an underground environment and 4) amendable to simple and inexpensive metal recovery steps. It is also important that the capital investment be low for the solution generation and; or regeneration plant.

Jan 8, 1965

By W. A. Koehler, M. E. Hinkle

INTRODUCTION THE oxidation of pyrites and marcasite in coal-mine strata to produce discolored acid mine drainage has long been explained by chemical reactions occurring in three stages: I. The iron sulphide minerals are oxidized by air in the presence of water to produce a nearly colorless solution of fer¬rous (iron) sulphate and some sulphuric acid. 2. The ferrous sulphate and part of the sulphuric acid combine with additional oxygen to form ferric (iron) sulphate. 3. The ferric sulphate hydrolyzes to form a reddish-brown precipitate and additional sulphuric acid. Nevertheless, chemical data alone are not sufficient to explain all observed facts. The first stage seems to proceed more slowly in the chemical laboratory than in nature. The second and third stages nor¬mally occur to a marked extent within a few days with raw mine water. However, the visible discoloration that characterizes these latter stages will not develop for months if the mine water is sterilized. By means of bacteriological techniques, two organisms have been isolated from acid coal-mine drainage. These are believed to have a part in promoting the chemical reactions summarized above. One organism is considered to be Thio¬bacillus thiooxidans, which is known to be able to convert elementary sulphur or sodium thiosulphate to sulphuric acid. Its relation to the formation of acid mine drainage has not yet been established. Apparently it does not promote the oxida¬tion of ferrous iron compounds in mine, drainage to the ferric state. The second organism has not been identi¬fied by name but is described as "Gram negative, non-spore-forming rods approxi¬mately 0.4 micron wide by o.8 to 1.0 micron long." A pure culture of this when added to sterile mine water will cause the latter to become amber and develop the typical rusty precipitate. However, it has not been found to convert sulphur com¬pounds to sulphuric acid. Further research is planned to determine whether or not these microorganisms play a significant part in the first stage of oxidation whereby pyrites and marcasite minerals go into solution. Some of the conditions found in abandoned sections of coal mines, such as a reduced percentage of oxygen and increased percentage of carbon dioxide in the air, as well as the existing temperature and acidity ranges, will be tolerated by and may even be favorable to these organisms. ACID COAL MINE DRAINAGE Acid coal mine drainage has been the concern of coal mine operators, industrial¬ists, sportsmen and public officials for many years. The amount of acid flowing into our streams in the coal-producing areas varies considerably from mine to mine and from

Jan 1, 1948

By Alfred R. Powell

Late in 1944 a group of petroleum and coal technologists was organized in Washington under the sponsorship of the Petroleum Administration for War and the U. S. Bureau of Mines. This group, known as the Technical Oil Mission, was placed under the authority of the Technical Industrial Intelligence Committee of the Joint Chiefs of Staff, which was then promoting the organization of other missions to be sent to Germany to obtain technical information regarding various industries in that country. The objective of the Tehnical oil Mission was to obtain technical data on German production of synthetic oil from coal and all other commercial practices and research projects connected with the oil industry. The primary purpose was to obtain such data as were immediately essential to assist the war against Germany and Japan, with secondary emphasis on technical information that would assist American industry after the end of the war. since oil-production facilities in Germany and the occupied countries controlled by Germany were the top targets for strategic bombing, the Technical Oil Mission was the first group under the Technical Induslrial Intelligence Com,mittee to enter Germany. A few members of the group flew to London in February 1945 and the majority of the remainder followed in March. In London they were joined by an equal number of British investigators and the combined mission was then sent into Germany under the authority of the Combined Intelligence Objectives Subcommittee (CIOS). A summary of the more important information gained by this combined British and American mission is presented below. German Oil Production The oil available to Germany, both natural and synthetic, and including production from occupied countries, reached a peak in late 1943 and early 1944 Production at this time was at the rate of 1,200,000 metric tons Per month, equivalent to 100,000,000 bbl. per year, or about 7 per cent of the wartime production in the United States. Of this production, jo per cent was crude oil from Romania and Hungary, 12 Per cent was crude oil from Germany itself, including Austria, 9 per cent cumprised coal-carbonization products, that is, tar and light oil, and only the remaining 29 per cent was synthetic liquid fuel made from coal or tar. Synthetic liquid fuel made in Germany was equivalent therefore to less than 2 per cent of wartime production of crude oil in the United States. The success of the strategic bombing campaign against German oil-production facilities is demonstrated by the fact that by September 1944 the Ploesti fields of Romania and much of the syrlthetic oil production had been eliminated, so that the amount of oil available to the German war machine was only 25 per Cent of the peak qualltity mentioned above. By early 1945, when the combined British and American oil mission was entering

Jan 1, 1947

By Alfred R. Powell

Late in 1944 a group of petroleum and coal technologists was organized in Washington under the sponsorship of the Petroleum Administration for War and the U. S. Bureau of Mines. This group, known as the Technical Oil Mission, was placed under the authority of the Technical Industrial Intelligence Committee of the Joint Chiefs of Staff, which was then promoting the organization of other missions to be sent to Germany to obtain technical information regarding various industries in that country. The objective of the Tehnical oil Mission was to obtain technical data on German production of synthetic oil from coal and all other commercial practices and research projects connected with the oil industry. The primary purpose was to obtain such data as were immediately essential to assist the war against Germany and Japan, with secondary emphasis on technical information that would assist American industry after the end of the war. since oil-production facilities in Germany and the occupied countries controlled by Germany were the top targets for strategic bombing, the Technical Oil Mission was the first group under the Technical Induslrial Intelligence Com,mittee to enter Germany. A few members of the group flew to London in February 1945 and the majority of the remainder followed in March. In London they were joined by an equal number of British investigators and the combined mission was then sent into Germany under the authority of the Combined Intelligence Objectives Subcommittee (CIOS). A summary of the more important information gained by this combined British and American mission is presented below. German Oil Production The oil available to Germany, both natural and synthetic, and including production from occupied countries, reached a peak in late 1943 and early 1944 Production at this time was at the rate of 1,200,000 metric tons Per month, equivalent to 100,000,000 bbl. per year, or about 7 per cent of the wartime production in the United States. Of this production, jo per cent was crude oil from Romania and Hungary, 12 Per cent was crude oil from Germany itself, including Austria, 9 per cent cumprised coal-carbonization products, that is, tar and light oil, and only the remaining 29 per cent was synthetic liquid fuel made from coal or tar. Synthetic liquid fuel made in Germany was equivalent therefore to less than 2 per cent of wartime production of crude oil in the United States. The success of the strategic bombing campaign against German oil-production facilities is demonstrated by the fact that by September 1944 the Ploesti fields of Romania and much of the syrlthetic oil production had been eliminated, so that the amount of oil available to the German war machine was only 25 per Cent of the peak qualltity mentioned above. By early 1945, when the combined British and American oil mission was entering

Jan 1, 1947

By John R. Green

ROTARY kilns, varying in construction, are used in a variety of processes. Products differ and operating conditions vary according to economic requirements. All of these variables influence the degree of instrumentation and type of control necessary or profitable to install. Products fired in rotary kilns are the results of combined temperature and time treatment and the interrelation of these two factors should be kept constantly in mind in the perusal of this paper. MEASUREMENTS OF KILN TEMPERATURE The securing of proper temperatures within the rotary kiln, either of the charge or of the kiln lining in the high fire zone, are basic objectives of kiln operation; therefore the measurement of these high-temperature conditions merits first consideration.. For these measurements, radiation pyrometers, properly designed and protected, have proved adequate, particularly where records or automatic control are desired, while optical pyrometers may serve as portable indicators. Light-sensitive devices or photoelectric cells in this service are capable of producing records as well as certain forms of automatic control. High-temperature measuring devices for rotary-kiln work should have the measuring unit protected from dust, as a continued accumulation of deposit would lower the readings. Fig. I shows a typical application of radiation equipment to a rotary kiln, mounted far enough away from the sighting hole through the kiln hood to be protected from puffs or stingouts and with a sighting tube having a series of settling chambers, to prevent dust from reaching the lens. Although dust conditions inside the kiln itself usually fluctuate considerably and have their effect upon the readings at that moment, such effects are not cumulative and show as a continuous fluctuation in the temperature indicated, provided the radiation unit and recorder are responsive to such slight and rapid temperature fluctuations. The ambient temperature to which a measuring unit is subjected fluctuates from possibly o° to over 200°F., therefore these changes should have no effect upon the final reading or upon the life of the measuring unit. A very narrow sighting angle is desirable, so that measurement of temperature may be made as far as possible into the high fire zone without. effect of the flame temperature. There should be some sighting means on the measuring unit, so that the proper field may be viewed. Measurement of wall temperature taken at a point where the charge has just left the wall is less affected by dusting conditions than when taken elsewhere. Factors Influencing Temperature Table I gives an outline of the factors that produce kiln temperatures and com¬ments on the possibility of measurement and control. Of greater number and of varied influ¬ence are the factors that control when, where and how the heat is delivered to the kiln, the type of flame and the rate of

Jan 1, 1941

By Frank S. McKenna, Myron A. Pugacz, Clarence E. Jackson

THE notched-bar impact test has proved worth while in certain applications as a test for control of the quality or the heat- . treatment of steel. In view of the serious thought that even so simple a test as the tensile test, has evoked during the past years, it is not surprising that the notched- bar impact test should have inspired much experimental work. The correlation of the great number of data has not been successful, although steady progress has been made toward a better understanding of this test. Progress has been made, especially, in the isolation of the effects of the many variables that control the results. The stress system imposed on a specimen with a notch is so complicated and un- predictable that no simple evaluation of the test has been possible. Because of this uncertainty, many engineers hesitate to use the notched-bar impact test, and this attitude may well continue until a better understanding of the effects of the variables in the test are available. Without doubt, any additional data that may be presented should be accompanied by as complete a description of the details of test as possible, so that it may be added to the general fund of information that is to serve as the basis for the theory of the notched-bar impact test. The many factors that may control the test results have been pointed out repeatedly. The importance of the effect of the type and dimensions of the specimen has been recognized. Most of the work reported by American investigators has been limited to small- size (Charpy) specimens tested as a simple beam; two types of notches (Fig. I) have been commonly used. Considerable data have also been presented by many investigators using a small specimen tested as a cantilever beam; this commonly being called the Izod test. Here, however, a shear component of stress makes the stress system even mare complex than that present in the simple beam type of test, hence a critical analysis is difficult. Much work has also been reported by investigators using the tension type of specimen. A second variable that must be con- trolled is the testing temperature. An indication that the tests were performed at room temperature is not sufficient, since in many steels a variation of a few degrees in the actual testing temperature may be sufficient to give an entirely different range of results. Other factors. such as the com- position and condition of the material being tested and the speed of test, should also be considered. Many investigators have contributed data and theoretical discussions on the problems encountered in notched-bar test-

Jan 1, 1944

By Raymond Ward

IN the past few years several papers have appeared dealing with different aspects of the oxidation of dilute alloys, especially with respect to the formation of internal oxides or subscales. Subscale has been defined1 as that layer or zone of oxide particles precipitated in a matrix of metallic metal in which the oxide particles are dispersed uniformly and occur by diffusion of the oxygen inward from the metal surface. Alloys composed of a solvent metal more noble than the alloying elements are subject to subscaling or internal oxidation. In these alloys the solute must be present in such quantities that if the alloy is exposed to an oxidizing atmosphere at elevated temperatures, the rate of diffusion of the oxygen into the metal will be greater than the rate of diffusion of the solute outward. There is a composition range of the iron-silicon system that falls into this classification. Knowledge of the nature and rates of oxidation of iron-silicon alloys is of great commercial importance, but very little information of this nature is available. Darken2 recently has made calculations to show the limits of concentration of silicon for which subscales are produced in iron-silicon alloys; however, the main thesis of his paper was to analyze and to explain the already existing data. The purpose of this paper is to present the effect of com position, temperature, time, and atmosphere on the type of scale-metal layer obtained and to give some qualitative indication of the effect of these variables on the rates of oxidation. Since this paper is a study of silicon steels that are available commercially, extremely low-silicon and high-silicon alloys are not included. EXPERIMENTAL PROCEDURE The alloys used in the experiment were taken from heats of silicon steel that ranged in analysis from 0.70 to 5.8 per cent silicon. This composition range takes in most of the commercial silicon steels. In Table I are listed the compositions of alloys used. Other than iron and silicon, the alloys normally contained approximately the following impurities: carbon, 0.03 per cent; manganese, 0.07; phosphorus, 0.008; sulphur, 0.02; copper, 0.07; tin, 0.01, and from nil to a trace of chromium, nickel and copper. All of the alloys used were melted in open-hearth furnaces, except where otherwise noted, and were hot-rolled to 0.100-in. plate. Samples approximately 1/2 in. square were then cut from these materials. So that the surface conditions of the samples used for oxidation would be standardized, each sample was ground through 000 emery paper immediately before oxidation. Two different techniques were employed in carrying out the oxidizing treatments. One consisted simply of heating the samples with free access to air. In this treatment the samples were set on edge on a refrac-

Jan 1, 1945

By Heinrich Ries

The manufacture of fire-brick represents one of the oldest branches of the clay-working industry in New Jersey, and is of more importance than is commonly imagined. The New Jersey clays were first used for fire-brick after the war of 1812, and one of the earliest records, according to Professor Cook, shows that clay was taken from Woodbridge to Boston in 1816, arid used for that purpose. The value of the clays of the Woodbridge district does not seem to have been well and widely recognized for some years, however, although in 1855 the statistics, given in the Geological Report, show that clay for making 50,000,000 fire-bricks was then taken annually from the pits at Woodbridge, Perth Amboy and South Amboy. Perhaps the oldest works in the State was that known as the Salamander works (no longer in existence), where brick were made as early as 1825. A little later, in 1836, John R. Watson established a factory at Perth Amboy, and in 1858 Sayre & Fisher began the manufacture of fire-brick at Washington. The works of W. H. Berry at Woodbridge began operations in 1845, and have continued up to the present clay, although in 1896 the name was changed to J. E. Berry. The works of Henry Maurer & Son were established in 1856, and those of M. D. Valentine & Brother in 1865. These latter were started for making bath brick; later, sewer-pipe, and, finally, fire-brick and other refractory shapes were produced. A branch-works, located at Valentine on the Central railroad of New Jersey, was started in 1887. Even in the last two years several works have begun the manufacture of fire-brick. These include factories erected by

Jan 1, 1904

By Alfred F. Brainerd

Some fifty years ago, iron-ore was discovered near the town of Sheldon, Franklin County, Vermont, in a vein out-cropping on a knoll near Black Creek, which empties into the Missisquoi River a couple of miles away. A short time after this discovery, the owners, Mr. TV. 0. Gadcomb and Hon. Lawrence Brainerd, both of St. Albans, commenced mining (mostly by open cut), and also erected a Catalan forge, from which iron blooms were produced, most of which were worked into bar-iron and used in the neighborhood of the forge, while some were shipped by Lake Champlain to Troy, Albany and New York. But by reason of the lack of any railroad connections, and an insufficient demand for the blooms, this forge was subsequently abandoned, and the material used in its construction removed to other places. Mr. Keith, of Sheldon, used for many years a mixture of this ore with bog-ore from Swanton, in a charcoal blast-furnace, the product of which he consumed partly in his own foundry, shipping, however, a considerable amount to Troy and New York. Accurate data as to this enterprise are not at hand. The same vein has since been traced for some 20 miles, and some prospecting has been done 011 its outcrops at Berkshire, Enosburg and a few miles east of St. Albans; but the vein being small, only a few car-loads of ore were taken out from these places. The commencement of the St. Albans Iron and Steel Works in 1872, and the erection in 1877 of a ten-ton Siemens open-hearth furnace for the manufacture of steel rails, opened a new use for this ore. The furnace-charge consisted of pig-iron, old mils, steel scrap, and magnetic iron ore, added towards the close of the heat. The ore

Jan 1, 1885

By P. H. Dudley

When we see the magnificent passenger-trains of from 8 to 12 coaches, drawn by locomotives weighing from 100 to 110 tons, at speeds of from 50 to 60 miles per hour between terminals, to make a schedule of 45 miles per hour, and freighttrains of from 50 to 75 cars of 60,000 pounds capacity, drawn by one locomotive, it is hard to realize that it lacks a few months of fifteen years since my pioneer 5-inch 80-pound rail for the United States was laid by the New York Central aid Hudson River Railroad Co., in July, 1884, on the Harlem line. Shorter passenger-trains, of from 4 to 5 coaches, are run much faster, notably the Empire State Express, the schedule of which for the 440 miles between New York and Buffalo requires 53.3 miles per hour, calling for a running-speed, for much of the time, of from 65 to 75 miles per hour, while higher speeds are very common. On other railroads laid with my 5 1/8-inch 80-pound rail, speeds of from 60 to 75 miles per hour obtain in daily practice. On many of the important railroads east of the Mississippi high speeds of from 60 to 70 miles per hour are part of the daily service. So many instances of speeds of 90, and even 100, miles per hour have been recorded that they must be considered as likely to occur on important lines, and provision must be made for them in the track. Solid mail-trains of from 6 to 8 cars are run from New York to Chicago, 1000 miles, in twenty-four hours; and, commeneing with the present year, shorter trains are running from Chicago to San Francisco, 2000 miles, in three and one-half days. In the freight-service equally important progress has been

Jan 1, 1900

By Roswell Johnson

To know the rate of decline of oil wells is very important, yet ordinarily we are prevented from getting this rate because the oil from several wells is put into one or a few tanks as soon as the wells have been connected to the power. The object of doing this is economy of tanks, pipes, labor and accounting. FIG. 1. But we are making a great sacrifice for this small economy. The advantages of the individual records are that we would know better: 1. When the well has ceased to be profitable. 2. When a well has gotten into bad condition. 3. The real record of the yield per acre and the rate of decline of the wells. The lease total is too mixed as to age of the wells for existing records to have much significance. To obtain such individual well records and more accurate logs are the great desiderata of satisfactory management of oil properties. 4. Which wells show the slowest decline-information which is valuable in locating new wells or purchasing adjoining leases.

Jan 6, 1917

By Edward Judd

CONSTRUCTION of the long projected Moffat tunnel, on the Denver & Salt Lake R. R., between Tolland and Irving, Colorado, is now actually and actively progressing. This 6.1-mile bore through the Rocky Mountains, at an elevation of about 9200 ft., will eliminate 33 1/3 miles of probably the most tortuous standard-gage track in the world, and at the same time will avoid the necessity for crawling over the snow-bound continental divide at an elevation of 11,660 ft Completion of the tunnel within the stipu-lated four years, is expected to nave an immediate effect on the develop-ment of the known coal fields in north-western Colorado, already penetrated at Craig, the present terminus of the road, while it will also enable the railroad to carry out the original designs of its founder, David H. Moffat, for through traffic from farther west. The intention now is to accomplish the latter object by an extension from McCoy following the canon of the Grand River down to a connection with the Denver & Rio Grande at Dotsero. Legal impediments to the financ-ing of the tunnel having been removed by action of the Colorado legislature in April, 1922, the Moffat Tunnel Improvement District issued bonds to the amount of $6,720,000 which have been widely and quickly distrib-uted through a New York banking house. Responsi-bility for the execution of the project has been vested in the Moffat Tunnel Commission, to which a board of consulting engineers has been appointed for carrying out the details of administration. This board includes D. W. Brunton and L. D. Blauvelt, of Colorado, and J. Vipond Davies and J. Waldo Smith, of New York; R. H. Keays, who has managed large tunnel projects in New York, is chief engineer for the Commission.

Jan 11, 1923

By Roy E. Dickerson, W. M. O Connor

The production of crude petroleum of the Bacuranao field, Cuba, fell off rapidly because no new wells Mere drilled. In December 1938, the total was 15 bbl. per day. The estimated average from this serpentine field for the year is 20 bbl. per day. The Motembo area produced an estimated average of 160 bbl. per day. Production in July was 215,946 gal of gasoline, or 165 bbl. per day. In August production was higher because a new well in the concession, the Luisa Marcela, produced 189 drums the first day and required pit storage. The Atlantic Refining Company of Cuba started a deep test upon a long, narrow, surface-defined anticline 3 km. south of Remedios, a town on the north coastal plain of Santa Clara province, in December 1938. The Atlantic Refining Co. is doing extensive seismograph arid gravity-meter work in Matanzas arid Santa Clara provinces. The Shell company was rigging for a deep test in western Havana province at a location about 2 km. west of the town San Antonio dc los Banos New Petroleum Law More serious attention was given by some of the major oil companies to the development of petroleum in Cuba as a, result of the passage of a Petroleum Law ill that country on May 9, 1938. Under the old mining lam of Cuba, which gave no special treatment to petroleum, the usual provisions giving reasonably satisfartory guarantees to encourage investmerit of foreign capital were either entirely lacking or were 30 ambiguously expressed as to require legislative action. Under the new law, Government royalty is fixed at 10 per cent with the provision that it will be reduced to 9 per cent on crude petroleum that is refined in Cuba. Royalty to the surface owner is 1 per cent. A surface tax on a sliding scale from 10¢ to 406 per hectare per year is applicable to all exploitation concessions granted under the law or adapted to its provisions. So export tax is payable upon petroleum. Stability of taxation

Jan 1, 1939

By W. M. O Connor, Roy E. Dickerson

The production of crude petroleum of the Bacuranao field, Cuba, fell off rapidly because no new wells Mere drilled. In December 1938, the total was 15 bbl. per day. The estimated average from this serpentine field for the year is 20 bbl. per day. The Motembo area produced an estimated average of 160 bbl. per day. Production in July was 215,946 gal of gasoline, or 165 bbl. per day. In August production was higher because a new well in the concession, the Luisa Marcela, produced 189 drums the first day and required pit storage. The Atlantic Refining Company of Cuba started a deep test upon a long, narrow, surface-defined anticline 3 km. south of Remedios, a town on the north coastal plain of Santa Clara province, in December 1938. The Atlantic Refining Co. is doing extensive seismograph arid gravity-meter work in Matanzas arid Santa Clara provinces. The Shell company was rigging for a deep test in western Havana province at a location about 2 km. west of the town San Antonio dc los Banos New Petroleum Law More serious attention was given by some of the major oil companies to the development of petroleum in Cuba as a, result of the passage of a Petroleum Law ill that country on May 9, 1938. Under the old mining lam of Cuba, which gave no special treatment to petroleum, the usual provisions giving reasonably satisfartory guarantees to encourage investmerit of foreign capital were either entirely lacking or were 30 ambiguously expressed as to require legislative action. Under the new law, Government royalty is fixed at 10 per cent with the provision that it will be reduced to 9 per cent on crude petroleum that is refined in Cuba. Royalty to the surface owner is 1 per cent. A surface tax on a sliding scale from 10¢ to 406 per hectare per year is applicable to all exploitation concessions granted under the law or adapted to its provisions. So export tax is payable upon petroleum. Stability of taxation

Jan 1, 1939

By Charles R. Fettke

The outstanding event of the year 1929 in the Appalachian area was the intensive drilling activity in the Bradford and Richburg pools of northwestern Pennsylvania and southwestern New York State, particularly the former, in connection with the continued extension of the five-spot system of water-flooding. More new development work was undertaken and completed than during any previous year since reclamation methods were first applied. This was due in part to an excellent price for oil and in part to discovery of the fact that more intensive methods (five-spotting) yielded greater profit. While several oil wells of comparatively large initial production were completed, no new oil pools of significance were discovered in the Appalachian area during the year. A number of small gas pools were opened in areas already surrounded by producing wells and at least three others in areas located some distance from any producing pools. Petroleum Development According to statistics of the U. S. Bureau of Mines, 33,7,57,000 bbl. of petroleum were produced in the Appalachian field during 1929 as compared to 31,060,000 bbl. in 1928.' Of the total 1929 production, 23,391,618 bbl. consisted of Pennsylvania grade oil as compared to 21,096,710 bbl. in 1928. The 1929 Pennsylvania grade production represents an increase of 37.4 per cent. over that of 1924. This increase can be attributed largely to the rapid development of water-flooding in the Bradford and Richburg pools. The Bradford field of northwestern Pennsylvania and adjaccnt portions of New York State experienced the busiest year since the boom days of the early eighties. Wells completed during the year totaled 2679.2 In spite of the high prices asked for acreagc, which in some of the choicest territory has been as high as $6000 an acre, a considerable number of properties changed ownership during the year. There is at present a pronounced tendency to consolidate the great number of small individually operated properties into larger units.

Jan 1, 1930

By C. A. Pierce

Studies of roof and floor movement are of interest to those actively engaged in mining. This is especially true in the case of an entirely new area where there is no precedent for guidance. The potash deposit being mined is in the southeast corner of New Mexico, about 20 miles east of Carlsbad. The deposit was formed by the land-locked, shallow, Permian Sea that extended through parts of western Texas, Oklahoma, Kansas, southeastern Colorado, and eastern New Mexico. The saline deposits vary from 500 to 4000 ft. thick. Neither of the companies operating in this area has delimited its commercial ore bodies. As all production so far has been from Federal and State leases, the Department of the Interior and the State of New Mexico have a direct interest in the development and extraction of these ore horizons. The ore is composed of an intimate mechanical mixture of sylvite (potassium chloride) and halite (sodium chloride). It lies generally in a horizontal bed varying from 5 to 12 ft, in thickness, and has a cover of approximately 1000 ft., consisting of about 500 ft. of salt beds and 500 ft. of sediments. The immediate mine roof for several feet is principally salt with some potash and clayey material. The next 500 ft. above, from the standpoint of structure, may be considered rock salt with a few inter-bedded potash members. The upper 500 ft. is of sedimentary (Permian and Triassic) origin and contains several water-bearing formations with flows varying from 10 to 500 gal. per minute. This water intensifies the interest in convergence problems as the ore and surrounding formations are water soluble. Potash salt (sylvite) and rock salt (halite) are plastic minerals. Plasticity is defined as a "property of solids by virtue of which they hold their shape permanently under the action of small shearing stresses but are readily deformed, worked, or molded under larger stresse."1

Jan 1, 1942

By C. A. Pierce

Studies of roof and floor movement are of interest to those actively engaged in mining. This is especially true in the case of an entirely new area where there is no precedent for guidance. The potash deposit being mined is in the southeast corner of New Mexico, about 20 miles east of Carlsbad. The deposit was formed by the land-locked, shallow, Permian Sea that extended through parts of western Texas, Oklahoma, Kansas, southeastern Colorado, and eastern New Mexico. The saline deposits vary from 500 to 4000 ft. thick. Neither of the companies operating in this area has delimited its commercial ore bodies. As all production so far has been from Federal and State leases, the Department of the Interior and the State of New Mexico have a direct interest in the development and extraction of these ore horizons. The ore is composed of an intimate mechanical mixture of sylvite (potassium chloride) and halite (sodium chloride). It lies generally in a horizontal bed varying from 5 to 12 ft, in thickness, and has a cover of approximately 1000 ft., consisting of about 500 ft. of salt beds and 500 ft. of sediments. The immediate mine roof for several feet is principally salt with some potash and clayey material. The next 500 ft. above, from the standpoint of structure, may be considered rock salt with a few inter-bedded potash members. The upper 500 ft. is of sedimentary (Permian and Triassic) origin and contains several water-bearing formations with flows varying from 10 to 500 gal. per minute. This water intensifies the interest in convergence problems as the ore and surrounding formations are water soluble. Potash salt (sylvite) and rock salt (halite) are plastic minerals. Plasticity is defined as a "property of solids by virtue of which they hold their shape permanently under the action of small shearing stresses but are readily deformed, worked, or molded under larger stresse."1

Jan 1, 1942