Search Documents

THE Joint Committee appointed to consider a Code of Ethics for Engineers recommends, after delib-erate consideration, that each participating Insti-tute or Society adopt the short simple Code of Ethics following this report. The Committee further recommends that the following method of interpreting and administering the Code be adopted by each participating Institute or Society after any necessary provisions have been, made in the Constitution and By-laws of the Organization. The President of each Society or Institute shall appoint a Standing Committee on Professional. Conduct, to administer the Code of Ethics. The duties of such a Committee shall be to interpret the Code and to render opinions on any cases of ques-tionable conduct on the part of members that may be submitted to the Committee. These interpretations shall be reported to the Executive Board of the Institute or Society who may approve these interpretations, or take such other action as may seem just and necessary. The reports of the Committee on Professional Conduct, when approved by the Executive Board, shall be printed in abstract and in anonymous form in the Institute's or Society's monthly journal for the instruction and guidance of fellow members. This Committee on Professional Conduct shall be appointed in each Institute or Society by the President holding office at the time of the adoption of this Code and shall consist of five member one appointed for five years, one for four years, a third for three years, a fourth for two years and a fifth member for one year only. Thereafter, the President then holding office shall appoint one member annually to serve for five years, and shall also fill any vacancies that may occur for the unexpired term of the member who has withdrawn. These appointments shall he made from among the older members of the Institute or. Society, so that advantage may be taken of their mature experi-ence and judgment. The Committee after appointment shall elect its own chairman and secretary. The Committee shall have power to secure evidence or other information in any particular case not only from the organization's own members, but if it should seem desirable, from men in other professions. The Committee may also appoint sub-committees to consider certain cases when deemed necessary.

Jan 3, 1922

By G. J. Benard

In the 1970’s, several plants have been built and others are in the design stage which use solvent extraction for recovery of copper from acid leach solutions. Other plants are presently being built for the recovery of nickel and cobalt from laterite ores by prereduction and ammonia leaching. A review will be given on the materials of construction for these leaching and solvent extraction processes. Many plants have factors in common which permit selection with a greater degree of accuracy. Based on pilot plant corrosion data, effective use of materials of construction includes proper selection of materials, substitution of lower cost plastics for alloys, and selection of materials resistant against chloride stress corrosion cracking.

Jan 1, 1974

By Donald R. Lessard

I. INTRODUCTION There is no question that the choice of an appropriate discount rate is a critical element in virtually all business decisions in extractive industries. The standard textbook approach relies on a single overall cost of capital for an entire firm, itself a weighted average of the firm's cost of debt and equity. But a single rate is appropriate only if the commercial risks and financing structures are similar for all projects under consideration. In extractive industries, appropriate discount rates are likely to vary greatly from project to project. Risks of projects differ markedly by mineral, by country in which the project is located, by stage in production, and by position in the project's life. Further, for a variety of institutional reasons, financing structures vary greatly in relation to these same variables and thus the discount rate appropriate to the entire investment and, in particular, to the sponsor's equity investment will vary even more markedly. Failure to select discount rates which reflect these differences can result in extremely distorted decisions. Our interest in this subject results from our ongoing research on alternative ownership and financing structures for large scale extractive ventures in less developed countries where risks to the various participants--the sponsors, the financiers, and the host government--vary dramatically with the different options. Given the magnitude of these differences, a single discount rate for all options is clearly inappropriate. However, there appear to be few guidelines for practicing managers to follow in setting appropriate rates. In this paper, we take a first step in this direction.

Jan 1, 1977

By Wang Yongjia, Steven L. Crouch

This paper describes a numerical method for computing time- dependent displacements and stresses in linear viscoelastic media. For such materials, the correspondence principle can be used to obtain the time-dependent solution directly from the solution to an associated elastic problem in Laplace transform space. The elastic solution, in turn, can easily be obtained by boundary element methods. The work presented in this paper is based on the displacement discontinuity method, adapted for the case in which the region of interest consists of two half-planes bonded together. A practical example of the method is given for a problem involving a panel of rooms and pillars in a thick layer of salt that is overlain by limestone. Viscoelastic behavior of the salt causes time-dependent displacements and stresses in both rock types.

Jan 1, 1982

By Helen L. Cannon

BOTANICAL methods of prospecting for metalliferous ores are based on the premise that deposits at depth may be reflected chemically in surface vegetation. For the past several years, on behalf of the Atomic Energy Commission, the U. S. Geological Survey has investigated on the Colorado Plateau the application of botanical methods to uranium prospecting. Results suggest that orebodies may be found under a considerable cover of barren sandstone through the absorption of uranium and associated trace elements by plants growing at the ground surface. Plant physiologists have demonstrated that uranium is a necessary nutrient for plant growth and therefore is present in all plants.' The amount present is small but measurable. The absorption of uranium by plants growing over ore deposits forms the basis, therefore, for a method of prospecting by plant analysis.

Jan 2, 1954

By R. C. Palmer

THE testing of flotation oils has occupied a large part of the time of the testing departments of various companies using the flotation process in the beneficiation of their ores. The great differences in ores and iii oils has made such work necessary as it has not been possible to select the oil best suited for the purpose without trial of many kinds. In fact, individual shipments of flotation oils from the same manufacturer will often differ so radically that the mill men have been forced to test every lot of flotation oil before its use in the mills. Further, although almost every imaginable product of the distillation of wood, from alcohol to pitch, has been tested in a more or less perfunctory manner by various people, few companies have allowed the results of their tests to be made public. This work was undertaken for the purpose of obtaining reliable data regarding the value as flotation agents of a number of products that are obtained from the distillation of wood by different methods, and incidentally to determine whether some of the products not used at present could be used. Large quantities of such materials are being wasted or burned in the wood-distillation plants of the United States, and if some use other than fuel could be found for these materials, such a use would represent a distinct saving to the country as a whole, would increase the profit of wood-distilling plants now operating and perhaps make it possible for others to operate which at present cannot do so except at a loss. At the same time it was thought that if such products can be used as flotation agents, then their use would serve to increase the number of oils and other products available for flotation purposes. It was also hoped that it might be possible to discover a substitute for some of the most effective but comparatively high-priced oils which are now used for flotation

Jan 8, 1916

By C. H. Frick

BEFORE presenting the main topic, as indicated by the title, this paper will give some of the high-spot history of the anthracite industry. INTRODUCTION The earliest recorded use of anthracite was in the year 1762, when a company of Connecticut pioneers discovered anthracite near the present city of Wilkes-Barre, Pennsylvania. In the early days of the industry, the coal was used only in large pieces, the smaller pieces being discarded to waste piles. As the output of the industry increased during the nineteenth century, uses were developed for somewhat smaller sizes down to and including pea coal. Early in the twentieth century, sizes smaller than pea, such as No. I and No. 2 buckwheat, were developed and used. Accu¬mulations of piles from current mining operations were still increasing; that is, the smaller sizes were still being discarded. It was not until after World War I that preparation of the so-called steam sizes began commercially. This was largely No. 3 buckwheat, which is screened through a 3f 6-in. round-hole screen and over a 332-in. or a M 6-in. round-hole screen. USE OF SMALLER SIZES The earliest recorded experience in burning the small sizes of anthracite for steam production, other than in a previous small experiment, was in the year 1913, when a size known as "boiler fuel" was introduced-a mixture of rice and barley (No. 2 and No. 3 buckwheat). At that time, there was still no method known for burning the still smaller sizes. TABLE I.-Screen Sizes Used for Small Sizes of Anthracite [ ] At the present time, various sizes down to and including No. 5 buckwheat are being prepared (Table I) from current mining and bank-reclaiming operations. The sizes of No. 4 and No. 5 buckwheat and smaller are generally being used for steam production in large boilers. The Pennsylvania Power and Light Co., following World War I, used 680,000 tons of anthracite per year, burned largely on stokers for production of steam, whereas for the year 1943 it used 1,940,000 tons of stoker sizes and 400,000 tons of smaller sizes for grinding and burning in pulverized form. This company has taken a very large part in the research and development of ways and means of burning these smaller sizes of anthracite, including the grinding of the very small sizes. This paper is particularly concerned with the latter feature.

Jan 1, 1946

By E. E. Donath, W. L. Crentz, J. D. Doherty

The principal washing problems in preparing coal for the synthetic fuel industry may be stated as: (1) ash removal for the Bergius process; and (2) sulphur removal for the Fischer-Tropsch process. A study is made of the effect of ash on oil losses during the elimination of the nonliquefiable portions of the coal in the hydrogenation process. The oil loss increases with ash content and results in increased consumption of coal, hydrogen, and power.

Jan 4, 1950

By Lee W. Abramson

INTRODUCTION The design of rock support for underground nuclear waste repositories requires consideration of special construction and operation requirements, and of the adverse environmental conditions in which some of the support is placed. While repository layouts resemble mines, design, construction and operation are subject to quality assurance and public scrutiny similar to what is experienced for nuclear power plants. Exploration, design, construction and operation go through phases of review and licensing by government agencies as repositories evolve. This paper discusses (1) the various stages of repository development; (2) the environment that supports must be de signed for; (3) the environmental effects on support materials; and (4) alternative types of repository rock support. Much of the information presented in this paper was derived from work conducted for Basalt Waste Isolation Project. Most of the information, however, would apply to other hard rock repositories. REPOSITORY DEVELOPMENT AND THE NEED FOR ROCK SUPPORT Repository development can be characterized by five general stages: exploration and design, excavation, waste emplacement, re trievability period, and backfilling. It is helpful to understand these phases of development to see where and when rock supports are required and how the design is verified. The description that follows is simplified. Details have been omitted, and future plans may not conform to this scenario.

Jan 1, 1984

By Orville R. Lyons, A. C. Richardson

Operating data is presented for a Bird centrifuge used to dewater coal treated at one preparation plant. The data include: (1 ) percentages of solids in centrifuge feed, cake, and effluent and the plant circulating water for a period of four consecutive operating shifts, and (2) screen-sizing data for a number of centrifuge feed, cake; effluent, and combined cake-effluent samples. An evaluation is included of the relationships between fine solids in the centrifuge feed and the total moisture content of the centrifuge cake.

Jan 3, 1950

By C. R. Tinsley

A strictly limited number of specialist project finance banks exists, with the necessary specialist personnel able to address project cost-competitiveness, cost and commodity forecasting, joint venture negotiations, and completion and sales undertakings. Different techniques of internal bank appraisal are applied, with the usual equity investment project valuation criteria being seldom useful for loan assessment purposes. Company attention paid to the preparation of a sensitivity structured bankable presentation can prove most effective for securing development project finance. Substantial scope is possible for savings of time and money.

Jan 1, 1985

By J. A. Herbst, O. A. Bascur

Fine coal cleaning by froth flotation has become common practice in the US with more than 73 kt/d (80,000 stpd) treated in this way. In spite of this large tonnage, developments in the automated control of coal flotation circuits have lagged significantly behind those for mineral systems. The primary reason is that instruments have not been available for the online measurement of carbon ash content or other critical variables in coal slurries. A second reason is that the influence operating variables have on coal flotation are not completely understood. During the last few years, some of the needed instrumentation has been developed, while an improved knowledge of the flotation process itself has occurred through mathematical modeling. As a result, certain control strategies for coal flotation are beginning to emerge. This paper attempts to evaluate several control strategies using a detailed flotation dynamic simulator, Dynafloat. After construction of a process matrix for the system of interest, promising alternatives for linking manipulated and controlled variables were analyzed. To develop combined grade and recovery control strategies, it was necessary to construct a grade/recovery map with the aid of the simulator to drive the system to known, final, feasible grade/recovery operating conditions. Finally, an advanced strategy that uses an on-line model to identify disturbances and take control actions is proposed.

Jan 1, 1986

By Samuel Doak

THE utilization of rotary kilns, of the well-known cement type, for the preparation of iron ores, for the blast furnace, has become of considerable economic importance within the past 10 years in certain localities, notably those where the native ores are lean. Such kilns may be used simply for the agglomeration of ores too fine to be charged into the blast furnace (i.e., ores whose loss in the dust catchers is excessive, and whose fineness is detrimental to the working of the furnace), or for the desulphurization of lump and fine ores the sulphur content of which does not exceed 6 or 7 per cent. The desulphurizing action can be combined with that of agglomeration provided the kiln is sufficiently large. Other processes have been developed for the same purpose, but while I am not able to draw a comparison between them by reason of lack of sufficient data, it is safe to say that the kiln, if properly dimensioned for the character of ore to be treated, will compare favorably in its results, both as to economy and quality of product, with any other process. It is not, however, as well adapted for the treatment of flue dust, as is a sintering operation, on account of the large percentage of fine coke contained therein. Any combustible entering the kiln at its feed end renders the process very much more expensive and unsatisfactory on account of the difficulty of controlling the temperature, also because of the rapidity with which long "rings" form, due to the increased heat at the cooler end of the kiln. The greatest value of the kiln at present is in the treatment of pyrites cinder; that is, the residue from pyrites ore after the extraction of the greater part of the sulphur. This cinder, while high in iron content, has too much sulphur remaining in it to be allowed to form a large part of the blast-furnace burden, without further treatment. It will range in metallic iron from 42 per cent., representing a very low-grade cinder, from a domestic pyrites, to 64 per cent. of the residue from the best Spanish ore, and the corresponding silica content will vary from the maximum of about 25 per cent. to 1 ½ per cent. The residual sulphur depends largely on the type of burner used in the original desulphurization. In general, the leanest original ores retain the greatest amounts of sulphur. In

Jan 9, 1915

By R. H. Rice

Turbo blowers for blast-furnace blowing have now been in use for some years, and a review of the experience gained and the present state of progress may be interesting.

Jan 1, 1915

By Carle R. Hayward

The growing importance of metallography has caused a corresponding interest in the improvement of apparatus for preparing specimens of metals and alloys for microscopic examination. The purpose of this paper is to describe an electric heating-furnace, a grinding- and polishing-machine, and a device for mounting specimens, which are used in the metallographical work at the Massachusetts Institute of Technology. These three pieces of apparatus were designed and made in the laboratory of the Institute, and each possesses some original features which may be of interest. Electric Heating-Furnace. The accurate control of heat necessary for metallographic work is best obtained by the electric-resistance furnace. Uufortunately, however, even the platinum-wound furnaces cleteriorate with use and ultimately burn out, while the cheaper resistance-materials are often short-lived. Since the resistance-coil must be replaced from time to time, it is of advantage to be able to make this change with as little trouble as possible, and this is an important feature in the furnace shown in Fig. 1. A is a cylindrical galvanized-iron can, with two handles, B. A porcelain tube, C, passes through the central hole in the cover of the can and rests upon the asbestos disk, D; the bottom of the tube is held in place by the asbestos ring, 3. The space, F, around the tube is filled with powdered magnesia. G is an ordinary assay-crucible, with the cover inverted so as to present a smooth top for supporting a second porcelain tube, H. The latter is wound with " Excello " resistance-tape, 0.014

Jan 1, 1912

By AIME AIME

COUNCIL.* PRESIDENT OF THE COUNCIL. JAMES F. KEMP : NEW YORK, N. Y. (Term expires February, 1913.) VICE-PRESIDENTS OF THE COUNCIL. S. B. CHRISTY BERKELEY, CAL. W. A. LATHROP PHILADELPHIA, PA. GARDNER F. WILLIAMS WASHINGTON, D. C. (Term expires February, 1913.) KARL EILERS NEW YORK, N. Y. WALDEMAR LINDGREN WASHINGTON, D. C. BENJAMIN B. THAYER NEW YORK, N. Y. (Term expires February, 1914.)

Apr 1, 1912

By Charles E. Nelson

THIS paper will outline briefly the practices commonly followed in this country for the melting and refining of magnesium and its alloys. The processes used for the various forms of primary magnesium, as jar as there are differences in the physical shape or behavior, will be discussed. The refining of general fine scrap or secondary magnesium was presented in an earlier paper and will be discussed briefly.1 Inasmuch as the use of fluxes is an essential part of all the melting and refining processes, this paper will deal with these in sufficient detail to point out their unique characteristics, in order to make their use more effective. The outline of this discussion will closely follow that of an earlier paper,2 with such changes and additions as seem necessary to bring it up to date. TYPES OF MELTING PRACTICE All melting and refining processes for magnesium and its alloys require the use of fluxes. These fluxes have a magnesium chloride base and other halide salts or oxides are added to give a density or behavior exactly suited to the particular melting practice. The successful handling of magnesium depends upon the proper use of the correct fluxes. There are four general methods of melting, summarized in the following paragraphs and treated in more detail in the section on Melting and Refining. Open-pot Method The open-pot method makes use of No. 230 flux, which provides protection during melting and a molten pool of flux into which the solid magnesium melts. The flux is stirred through the molten metal bath and agglomerates oxide or similar foreign bodies;, on quiet standing, it separates away, leaving the refined metal ball floating in an encircling layer of molten flux. It forms only a thin fluid film over the surface of the molten metal, which may be parted for hand-ladling processes and tends to cover the metal again after the ladle is removed. A very light dusting of the pot surface with fresh flux immediately after the ladle is removed is desirable. The open-pot method is used generally in the following processes: (I) alloying and remelting in the production of ingot, (2) in sand foundries for premelting and to a smaller extent for the production of small castings, (3) in permanent-mold founding for premelting and also direct ladling to castings, (4) for continuous methods of preparing metal in the production of billets or ingots from which wrought products are fabricated, (5) in general scrap recovery. Crucible Process The crucible process makes use of No. 310 flux, which has the property of being thinly fluid at the start, to provide protection and refining qualities, and then drys out or thickens after a time, leaving a protecting crust on the pot surface until the time of casting. At that time it can be readily skimmed off or held back, thus allowing the contents of the crucible to

Jan 1, 1946

By AIME AIME

Council. * PRESIDENT OF THE COUNCIL. JAMES F. KEMP NEW YORK, N.Y. (Term expires February, 1913.) VICE-PRESIDENTS OF THE COUNCIL. S. B. CHRISTY BERKELEY, CAL. W. A. LATHROP PHILADELPHIA, PA. GARDNER F. WILLIAMS WASHINGTON, D. C. (Term expires February, 1913.) KARL EILERS NEW YORK, N. Y. WALDEMAR LINDGREN WASHINGTON, D. C. BENJAMIN B. THAYER NEW YORK, N. Y. (Term expires February, 1914.)

Mar 1, 1912

The Institute maintains for the use of members (and especially for the use of out-of-town members) a reading and writing room, where all usual office facilities are available, including telephone, telegraph, receipt, forwarding and care of mail and express packages, etc. A file of current magazines is also maintained in this room, and the Institute's staff will lend its best efforts to serving the members in connection therewith. The Institute also maintains for the use of its members free dressing rooms, library research department, etc. Attention is called to these facilities at the present time in the belief. that they may be especially useful to out-of-town members in connection with the Meeting.

Jan 5, 1918

By Kingman, Robert I.

SUFFICIENT testing has been .performed with the Dutch State Mines Cyclone for thickening and desliming flotation feed at the concentrator of the National Lead Co., Tahawus, N. Y., to prove its application for this work. It is the purpose of this article to present some of the test results, operational details and advantages of cyclone thickening and classification. The metallurgy of the mill operation was described by Frank R. Milliken, assistant manager of the titanium division.

Jan 1, 1950