Search Documents

By F. W. Bowdish

A theoretical and experimental laboratory study has shown that the rate of breaking of oversized particles in a ball mill is proportional to 1) the concentration of such particles, and 2) the area of the balls, provided that the balls are larger than a certain size relative to the particles. If all undersized material were removed as formed, the rate of breaking would be almost independent of the quantity in the mill. Rate equations are given which are similar to those for zero, first, and second order reactions. Deviations of small balls from the equation for a second order phenomena are quantified by a factor called "nipping efficiency." Some data are correlated by a dimension-less equation, which is used to estimate nipping efficiencies from data not in the correlation. The investigation described here was undertaken after a literature survey revealed that little was known concerning the mechanism of breaking of particles within a ball mill and the effect of this mechanism upon grinding rates. One paper, by Roberts1 , offered a theory concerning the mechanism of breaking, and a rate equation for the breaking of particles larger than some size to particles smaller than that size. That paper provided the starting point for a theoretical and experimental investigation of grinding under carefully controlled conditions. THEORETICAL CONSIDERATIONS In his paper on the probability theory of ball mill grinding, Roberts theorized that "... a given expenditure of power leads either to a certain number of point to point blows per bp-hr or to a certain distance of line contact per hp-hr ..." He assumed that the balls touch each other during each blow or during moving contact. Then he said that a volume of pulp, dependent upon the size being considered, would be covered per minute within which all oversized particles would be crushed to particles smaller than that size. Naturally, the higher the concentration of oversized particles in the pulp, the higher the rate of which they would be broken. From this reasoning Roberts obtained the differential equation -dC/dt = k hp/ton C (1) where k is a constant for any size of particle, density of particle, and moisture content of pulp. C is the percentage of oversize in the material to be ground, t is the time, and hp/ton is the power input per ton of material in the mill. He then integrated the equation to log Co/Ct = k/2.3 hp/ton t , where Co and Ct are the percentage of oversize at time zero and t respectively. By always using the same quantity of material in a mill and assuming that it required constant power to run the mill, he was able to combine the horsepower per ton factor with the other constants to give an equation for a first order rate.

Jan 1, 1961

By L. T. Stanley

A method is described whereby the behavior of the front is approximated when gas is injected into a thick reservoir having reasonably homogeneous properties. The method is applied to the Abqaiq field of Saudi Arabia. The producing member is the Arab-D, a high-permeability calcarenite which has no continuous betlding planes. Field performance indicates the injected gas to be partially miscible with the reservoir oil because gas volume factors experienced are lower than those predicted by the gas law. Eqlrilibril~m calculations confirnz ihis and also show that the volume factor may vary appreciably, depending on the relative quantities of oil and gas in contact in the reservoir; consequently, volutnetric balances are made for the purpose of determining the behavior of the gas volume factor during injection history. The effect of gravity segregation on position and shape of the gas front is approximated by dividing the producing section into three zones vertically and tracing the movement of the average interface in each zone, with counterflow of oil and gas taking place betweell zones behind the front. This results in a gas front that advances more rapidly along the top of [he formation than along the base, producing an "umbrella" effect in cross section that becomes more pronounced as the front progresses. The calculations cover the gas-injection period of Abqaiq field history through 1958, and the position of the gas front is plotted at one-year intervals. Finally, some comparisotls between the calcrlated fronial position and the gas-oil contact as Measured by neutron logs are made. INTRODUCTION Fig. 1 is a structure contour map of the Abqaiq field. For analytical purpcses, the field has been divided into two areas designated A and B, as shown on the map. Gas injection into Area A was begun in early 1954 into two wells located near the crest of the structure on the north-south axis of the anticline. During the period covered by this paper, the average injection rate has been 122 MMscf/D with a maximum sustained rate of 160 MMscf/D. The reservoir pressure has been maintained at 2,450 psig since start of gas injection. The reservoir originally was undersaturated but, prior to pressure maintenance, the pressure was drawn below the bubble point in most of the Area A section, creating an in-place free-gas saturation of 8 per cent at the crest of the structure. The average critical gas saturation is 13 per cent established by laboratcry core tests. That the entire reservoir remained below critical gas saturation prior to gas injection is borne out by the fact that none of the crestal wells have exhibited high gas-oil ratios during production history. The Area A reservoir is a carbonate section about 200-ft thick having average porosity and permeability of the order of 22 per cent and 500 md, respectively. The productive horizon is the Arab-D member of Jurassic age and is encountered at an average depth of

By Ralph H. Sweetser

MUCH progress in -blast-furnace construction and in the manufacture of firebrick for furnace linings has been made since the publication of Bulletin 130 of the U. S. Bureau of Mines on "Blast-Furnace Breakouts, Explosions and Slips, and Methods of Prevention," by F. H. Willcox in 1917. At the time of publishing this report comparatively little information was available to blast-furnace men as to the fundamental facts relating to the character of blast-furnace refractories. Some of the accepted theories of only a few years ago have been completely reversed. The mortality of blast-furnace linings used to be so great that nearly every furnace plant had one or more complete linings in the brick shed ready for use in case of a lining suddenly "going out"; it was generally accepted that a furnace could not "keep her lines" more than two or three years at best, and often a hot spot in the shell would develop, or a breakout occur in the hearth or bosh within a year or two after blowing in on a new lining. In some respects these frequent relinings were not so detrimental as to he a complete loss because they afforded opportunities to take advantage of advances in blast-furnace practice. At present the cost of relining has greatly increased, but the life of a lining has also increased. Anything less than five years on a lining is now considered a short blast.

Jan 1, 1932

By P. Niessen, W. C. Winegard, C. J. Beingessner

DURING the last 10 years, several grain-growth studies have been made using zone-refined metals with controlled amounts of solute to elucidate the interaction of solute with moving boundaries. In all these studies, it was more or less implicitly assumed that the alloys used were, after recrystallization and grain growth, homogeneous within the grains with respect to solute and lattice defects. This note deals with observations made on microstructures originating from solidification of dilute alloys and from grain growth. Briefly, the experimental procedure used in these studies was the following: zone-refined cadmium and master alloys were melted and cast in Pyrex under vacuum to produce bars 14 mm in diam and about 150 mm long. These bars were cut into 8-mm-thick slices which were mechanically and chemically polished. The specimens were then deformed 30 pct in compression and given a 1-week anneal at 260°C in argon. After this anneal, a second deformation produced completely recrystallized samples 4 mm thick. The time-temperature controlled anneals were carried out in a bath of silicone oil. After the grain-growth anneal, the specimens were polished in Gil-man's' solution (33 g CrOs, 6 g NazSO, in 100 ml of water). Several etches were used depending on the alloy investigated, but mostly a mixture of concentrated HC1 and HNOj (98:2 vol) was employed. In all the alloys examined, the ease with which substructures could be revealed depended strongly on the crystallographic orientation of the surfaces of the grains. However, very frequently the microstructures to be discussed here etched up over broad areas comprising several grains. Fig. 1 is a micrograph of a Cd-0.05 at. pct Mg alloy annealed for 100 sec at 270°C. Different substructures are seen in this photograph. A denotes the now existing grain boundaries. The well-defined lines and points marked B are the remains of a solidification substructure. The lines are boundaries between cell colonies, and the points are nodes located on regular two-dimensional cells. This cellular structure has the same appearance as that found by weinberg2 for rapidly quenched Zn-Au alloys. The "ghost boundaries", marked C, are very similar in appearance to a grain boundary array in a polycrystalline sample. Repeated polishing and etching showed that all the substructures observed were three-dimensional. To date, the ghost boundaries have been clearly observed in all samples containing 0.005, 0.01, 0.05, and 1 at. pct Mg, and in samples containing 0.01 at. pct Zn. Attempts to outline these ghost boundaries in cadmium alloys containing 0.01 at. pct Ag and Au were only partially successful. In these alloys, parallel lines, having a resemblance to the ghost boundaries in the Cd-Mg and Cd-Zn alloys, were observed, but it was not possible to obtain complete arrays of ghost boundaries which extended over several grains. It is possible that a different etch than that presently employed would reveal the ghost boundaries in the Cd-Au and Cd-Ag alloys as clearly as in the Cd-Zn and Cd-Mg alloys. A close examination of the ghost structure showed that it consisted of linear etch-pit arrays, Fig. 2. The ghost boundaries were resolvable even in grains which showed over-all faceting due to the etching, as seen in the corner of Fig. 2. The general appearance of the ghost structure suggests that it originated during grain growth. This is supported by the observation that the mesh width in the ghost-boundary array generally increased with increasing final grain size. To test whether the ghost structure was formed during the long homogenizing anneal or during the grain-growth anneal, some as-cast samples were deformed and given a grain-growth anneal. This anneal was terminated by air cooling or

Jan 1, 1967

By Donald H. McLaughlin

THE activity and enthusiasm of pioneers still prevail among workers in applied geophysics1.- Within the year, new devices have .been tried out, instruments and technique have been improved and the methods of application to commercial problems have been increased in many ingenious ways. There is still great need for more skillful interpretation of results in terms of geology, but oil the whole geophysical prospecting is making encouraging progress toward finding its proper place and function in engineering and geological practice. Spectacular successes continue to be reported, particularly .from the Gulf Coast, where the race for salt domes has not slackened, and encouraging results have been giined elsewhere in the mapping of structures in the search for oil. In the mining field, however, it can hardly be claimed that the same measure of success has been obtained, for brilliant efforts worthy of wide recognition have been overshadowed to some eatent by the unfortunate outcome of surveys undertaken unwisely without recognition of the limitations of the work. Consequently, hopes were aroused that could not be fulfilled, and it must be admitted in an impartial survey that there are a few regions, chiefly in the far north, where the standing of geophysical prospecting is somewhat doubtful and where the course of public opinion regarding it shows a certain similarity to the history of the market during the past few months. Reliable work, however, is steadily going 011 and it can confidently be expected that the methods will eventually be regarded in many regions as an essential part of the technique of securing geologic data needed for intelligent exploration.

Jan 1, 1930

By W. D. Johnston, T. P. Thayer

THE minerals that collectively are known as chromite form an isomorphous series of the general formula (Mg,Fe) 0. (Cr,Al,Fe) 203. So wide is the range in chemical composition in this group that chrome ore consisting entirely of the mineral chromite may range from less than 30 pct to more than 60 pct Cr203. The most comprehensive published data on the chemical com- position of chromite are by Stevens,62 who made complete analyses of 52 samples of chromite concentrate from many localities in North, Cen- [ ] tral, and South America. These samples were mechanically purified to remove associated silicates and might be regarded as the cleanest chromite that could be obtained by any mechanical milling process. Fig 1 shows the predominant zone of isomorphism, within the triangular prism of composition defined by the mineralogical end members of the series, wherein his analyzed samples fell.

Jan 1, 1949

Trans. No. Place Date Vol. Page 1. Wilkes-Barre Pa......May.71 1 3 2. Bethlehem, Pa.........Aug., '71 I 10 3. Troy, N.Y............Nov..: 71 1 13 4. Philadelphia, Pa........Feb., 72.. 1 17 5. New York. N. Y.*......May, '72.. 1 20 6. Pittsburgh. Pa.........Oct..' 72.. 1 25 7. Boston, Mesa..........Feb., '73.. 1 28 8. Philadelhia, Pa.*......May, '73.. 2 3 9. Easton, is............Oct..' 73.. 2 7 10. New York, N. Y.......Feb..' 74 . . 2 11 11. St. Louie. Mo.*........May,' 74 . . 3 3 12. Hazleton, Pa...........Oct., '74.. 3 8 13. New Haven Conn......Feb., '75.. 3 15 14. Dover,N.J.*..........May, 75.. 4 3 15. Cleveland,O...........Oct. 75. 4 0 16. Washington D. C......Feb.'' 76.: 4 18 17. philadelphia, Pa.......June,: 76.. 5 3 18. Philadelphia Pa........Oct 76.. 5 19 19. New York, N. Y.......Feb: '77.. 5 27 20. Wilkes-Barre. Pa.*.....Mag :77.. 0 3 21. Amenia N. Y..........Oct. 77.. 6 10 22. Philadeiphia Pa........Feb.;' 78. . 6 18 23. Chattanooga' Term.*. . . May' 78. . 7 3 24. Lake George: N. Y....: Oct. 78. . 7 103 25. Baltimore, Md.*.......Feb:' 79.. 7 217 26. ~ittsburgi, Pa.........~a;' 79.. 6 3 27. Montreal, Canada......~ept.;' 79.. 8 121 28. New York, N. Y.*......Feb., '80.. 8 275 29. Lake Superior, Mich....Aug., '80. . 9 1 30. Philadelphia, Pa.*......Feb., '81. 9 275 31. Staunton, Va..........May, '81. .10 1 32. Harrisburg, Pa.........Oct.. '81..10 119 33. Washington, I). C.*....Feb., '82. . 10 226 34. Denver. Colo..........Aug.. '82. . ll 1 35. Boston. Mass.*.........Feb.. '83..11 217 38. Roanoke, Va...........June, '83.. 12 3 37. Troy, N. Y...........Oct.. '83. .12 175 38. Cincinnati. O.*.... Feb, '84..12 4 39. Chicago Ill............May, '84. . 13 1 40. philadelphia, Pa........Sept., '84. . 13 285 41. New York, N. Y.*......Feb., '85. . 13 586 42. Chattanooga, Tenn.....May, '85..14 1 43. Halifax, N. S..........Sept., '85.. 14 307 44. Pittsburgh, Pa.*........Feb.. '86 . . 14 587 45. Bethlehem. Pa.........May, '86 .. 15 Ixiii. 46. St. Louis, Mo..........Oct, 86.. 15 Ixx. 47. Scranton, Pa.*.........Feb.', '87. . 15 lxxvi 48. Utah and Montana.....July '87.. 16 xvii. 49. Duluth, Minn...........July' '87. -16 xxiv. 50. Boston. Mass.*.........Feb.: '88. . 16 xxviii. 51. Birmingham, Ala.......May, '88. .17 xix. 52. Buffalo N. Y..........Oct. '88.. 17 xxiv. 53. New york, N.Y........feb.' ;89 . . 17 xxxi. 54. Colorado..............June' 89 . . 18 xvii. 55. Ottawa, Canada........Oct., 89. . 18 xxiv. 56. Washington, I). C.*. . . Feb. 90. .18 xxx. 57. New York, N. Y........sept:, '93. .19 vii. 58. New York, N. Y.*......Feb. '91. . 19 xxv. 59. Cleveland, O.......... June, :91 . .a xvi. 60. Glen Summit, Pa.......Oct, 111. . 20 lxi. 61. Baltimore, Md.*.......Feb.: '92. .21 xix. 62. Plattsburg, N. Y.......June, '02. . 21 xxxiii. 03. Reading. Pa...........Oct., :92. .21 xliv. 64. Montreal. Canada*.....Feb. 93..21 65. Chicago, Ill............aug.: '93..22 XI. 66. Virginia Reach. Va.*. ...Feb., '04. .24 xwl. 67. Bridgeport Coon.......Oct., '94..24 xxx?. 08. Florida ...'............Mar., '95. .25 xix 69 Atlanta. Ga......... Oct 95. 25 xi 70. Pittsburgh. Pa.*........Feb., '96.. 26 xvii. Trans. No. Place Date Vol. Page 71. Colorado..............Sept. '96. .26 xxix. 72. Chicago, Ill............Feb.. "97.. 27 xvii. 73. Lake Superior..........July '97. .27 xxx. 74. Atlantic City, N. J.*. ..Feb.: :98. .28 xvii. 75. Buffalo N. Y..........Oct. 08. .28 XXXVI. 76. New York,N. Y.*......Feb.: '99. .29 xvii. 77. California.............Sept., ;99. . 29 xlix. 78. Washington, D. C.*.....Feb., 00. .30 xix. 79. Canada...............Aug.. '00. .30 xlv. 80. Richmond. Va.*........Feb.. '01. . 31 xix. 81. Mexico................Nov..'01.. 32 cxviii. 82. Philadelphia Pa. $......May, :02. . 33 xxxv. 83. New Haven, Conn......Oct.. 02.. 33 xlvii. 84. Albany N. Y.*........Feb '03. .34 xxiii. 85. New York, N. Y........Oct.': '03. .34 xi. 86. Atlantic City. N. J.*....Feb., '04. .35 XXIII. 87. Lake Superior..........Sept.'04. .35 dii. 88. Washington. D. C......May' '05. .36 xlii. 89. British Columbia.......July, '05. . 36 90. Bethlehem. Pa.........Feb. '06. .37 xli. 91. London, England.......July: '06. .37 xlviii. 92. New York, N. Y........April, '07. . 38 lii. 93. Toronto, Canada.......July. '07. .38 lix. 94. New York, N. Y........Feb., :08. .39 xli. 95. Chattanooga, Tenn.....Oct.. 08..39 xlviii. 06. New Haven Conn......Feb. '09. .40 xli. 97. Spokane,Wash.........Sept:.'09. .40 xlviii. 98. Pittsburgh, Pa.........Mar.,'10. .41 xxxviii. 99. Canal Zone............Nov.,'10. .41 dv. 100. Wilkes-Barre, Pa.......June. ' 11. . 42 xxxiv. 101. San Francisco, Cal......Oct.. '11..42 xliv. 102. New York. N. Y.*......Feb 12. .43 Ixxvii. 103. Cleveland, Ohio........0ct;' '12.. 44 wii. 104. New York, N. Y.*......Feb.. '13. .45 xv. 105. Butte, Mont...........Aug., '13. .46 ?' 108. New York, N. Y........Oct., 13..47 vii 107. New York. N. Y.*......Feb.. '14..48 xv. 108 Salt Lake City. Otah Aug. :l. 49 5: 109. Pittsburgh, Pa.........Oct., 14. .50 vii. 110. New York, N. Y.*......Feb., '15. .51 xvi. 111. San Francisco, Cal......Sept., '15. .52 xii. 112. New York,N. Y.*......Feb., '16..54 xvi. 1 Arizona...............Sept.,'l6. .55 VII 114. New York, N. Y.*......Feb., '17: .56 vii. 115. St. Louis, Mo..........Oct.. '17..57 vii. 116. NewYork,N. Y.*......Feb.. '18..59 xvii 117. Colorado.....:........Sept.,'18. .60 vii. 118. Milwaukee, Wis........Oct.. '18. .60 x:!: 119. NewYork,N. Y.*......Feb., '19..61 xi. 120. Chicago...............Sept.,' l9.. 62 VII. 121. New York, N. T.*......Feb., '20..63 ix. 122. Lake Superior District. .Aug., '20.. 66 ix. 123. New York, N. Y.*......Feb., '21. .66 xiii. 124. Wilkes-Barre, Pa...... Sept.. : 21.. 66 xix. 125. New York, N. Y.*......Feb., 22. .67 ix. 126. San Francisco. Cal......Sept.,:22. .68 xxix. 127. New York, N.Y.*.....Feb., 23. .69 xxix 128. Canada...............Aug., '23. .69 xxxv! 128.129. New York, N. Y.*......Feb., ;24. .70 xxxi. 130. Birmingham, Ala.......Oct. 24. .71 xxxiii 131. NewYork.N Y.*......Feb.: '25.. 71 xxxviii. 132. 131.Salt Lake City, Utah .. .Sept., '25. .73 xvi 133. New York, N. Y.*......Feb., '26. .73 xxii. 134. Pittsburgh Pa ....... Oct.. '26. .74 xv. 135. New York,' N. Y.*............Feb., '27. .75 x::: 135.136. NewYork,N. Y.*......Feb., '28..76 104 137 NewYork.N. Y.*......Feb., '29. .291 116 138.San FranciscoYork,N.Y. Cal..........Oct. 29..308 406 139. New York, N. Y.*...Feb., '30..30H 1321

Jan 1, 1930

By J. Gurland

A method of measuring the degree of contact between grains of 1 phase in multiphase alloys is derived. It is shown that the number and the areas of contacts between grains can be determined by metallographic analysis. Relations between the area of contact, the dihedral angle, and the mean free path of spherical grains are developed. It is often desirable to interpret the mechanical behavior of alloys in terms of structural features observed under the microscope. A quantitative description of microstructures of multi-phase alloys requires consideration of geometrical and topological factors such as the amount, size, and shape of grains and the continuity of the constituent phases. The number and dimensions of grains may be metallographically determined by applying the methods described by Smith and Guttman1 and by Fullman2 in their papers on the measurement of particle size and internal boundaries in opaque bodies. The present work intends to show that the same methods can be used to evaluate some of the parameters of phase continuity; namely, contiguity, number of contacts, and areas of contact of grains of 1 phase. Application of these concepts may be found in such problems as the calculation of electrical conductivity of 2-phase alloys, or the evaluation of the length of fracture path through grains of a brittle phase more or less dispersed in a matrix. I. DEFINITION The following definitions and derivations are based on 2-phase alloys, of which the units of the microstructure are grains. Contiguity is defined as the average fraction of surface area shared by 1 grain of a phase with all neighboring grains of the same phase. In a 2-phase alloy of constituents A and B, the contiguity of phase B is given by: where Cb is the contiguity of phase B aBß is the average area of contact between a grain of phase B and adjacent grains of phase B, aAB is the average area of contact between a grain of phase B and adjacent grains of phase A. The contiguity is a measure of the average degree of contact between grains of phase B in the 2-phase mixture. The ratio varies from 0 to 1 as the distribution of phase B changes from a completely dispersed to a fully agglomerated structure. Smith and Guttman1 have shown that the relative areas of 2 kinds of interfaces in a volume are directly proportional to the number of interfaces of each type intersected by a random line. The lines can be drawn on metallographically prepared surfaces as long as these are random sections through the sample. The contiguity ratio of phase B then becomes: Cb = 2NBB/NAB + 2N BB [2] where: NBB is the number of interfaces between grains of phase B intersected per unit length of random line. Nab is the number of interfaces between grains of phase B and grains of phase A intersected per unit length of random line. The factor 2 arises in Eq. [2] because each interface B-B is associated with 2 grains of B-phase, whereas the interface A-B involves only 1 grain of B-phase. The calculations of contiguity do not require any assumption as to volume fraction, particle size, or particle shape. Fullman2 gives an expression for the determination of the mean free path between particles. The mean free path PB between grains of phase A, i.e., through grains or agglomerates of phase B, may be found from the relationship: PB =2fB/NAB [3] where fB is the volume fraction of phase B. The calculation of the mean free path is independent of grain shape and grain size distribution. The calculation of the number of contacts and of contact area requires assumptions of grain shape, grain size, and contact shape. In the case of uni-

Jan 1, 1959

By WALTER VOIGTLANDER

FOR nearly 100 years wire rope has been fabricated in much the same way. To the great majority of mine superintendents wire rope is just wire rope, little or no semblance of individuality or identifying characteristics. Such an impression was fairly justified until three or four years ago when a practical means was found of performing or preshaping the wires and strands. This discovery permitted a revolutionary change in wire rope manufacture. Instead of merely twisting a number of wires into a strand, then twisting several strands into a complete rope (which twisting would naturally result in great internal strain, thus reducing the resiliency and over-all efficiency of the completed rope), the preformed wires and strands were laid in place without force or twisting. The obvious result was a rope more nearly approximating mechanical perfection. The applied loads are more evenly distributed throughout the component wires and strands, thus reducing unbalanced wire stresses. This results in a higher safety factor. The fact that preformed rope will not unravel when untied at the ends proves the absence of a torsional stress that exists in ordinary rope. A greater useful allowable stress in the wires is therefore possible in actual operating service.

Jan 1, 1926

By V. H. Whihelm

Since 1935 California has enjoyed a remarkable cycle of discovery, which has placed the state in a very satisfactory position in regard to oil reserves. Most ol the geophysical plays have been drilled and it is possible that new discoveries must be made by the application of careful geologic and stratigraphic studies. During 1940 only one new field was discovered, which, although not of major importance, may lead to additional discoveries. During the year, 113 wildcats were drilled. New discoveries, extensions and a reappraisal of discoveries made in 1939 will not approximate over 50,000,000 bbl., as against an estimated withdrawal during the year of 224,000,000 barrels. Demand in terms of crude for 1940 was 632,000 bbl. per day as against 626,000 bbl. per day for 1939. Demand for gasoline was the same as in 1939, but the demand lor fuel oil increased 3.8 per cent. Compared with 1939, Japanese shipments decreased from 75,786 bbl, per day to 61,000 bbl. per day, but the balance of Pacific foreign shipments increased from 59,409 bbl. per day to 61,304. Total with-drawals from storage during the year will approximate 7,000,000 bbl., almost all of which is fuel oil. Drilling activity was slightly greater than in 1939 and accounted for 890 new producing wells as against 851 for 1939 (Table 3). Production averaged 611,900 bbl. per day as compared with 614.,842 bbl. per day for 1939. The productive acreage figure of the state was increased by 4000 through discoveries and extensions. New Discoveries Los Angeles Basin District Del Vdle Field.—Northwest of Newhall, where the first oil well in California was drilled, R. E. Havenstrite completed his Lincoln No. I well, flowing 390 bbl. of 50" gravity oil together with 7000 M CU. ft. of gas. Later the well was recompleted, after cutting off the gas, for 950 bbl. of 34" gravity oil. The type of structure from which this production is coming is a plunging anticline, complicated by faulting. The Lincoln No. I well uncovered approximately 180 ft. of net sand. This field contains a gas cap and its indicated productive area approximates 500 acres. An intensive wildcat drilling campaign is expected during this coming year in the district in the vicinity of the Del Valle field. Extensions and Deeper Sand Developments Los Ange1es Basin District Athens Field.—On the northwest plunge of the Athens structure, the Thorley Oil Co. completed its No. 12-1 well, flowing 250 bbl. of 3 2" gravity oil from a depth of 8097 ft. The area in which the well is located is complicated by faulting and it is impossible at this date to determine the importance of this deep-zone discovery.

Jan 1, 1941

By V. H. Whihelm

Since 1935 California has enjoyed a remarkable cycle of discovery, which has placed the state in a very satisfactory position in regard to oil reserves. Most ol the geophysical plays have been drilled and it is possible that new discoveries must be made by the application of careful geologic and stratigraphic studies. During 1940 only one new field was discovered, which, although not of major importance, may lead to additional discoveries. During the year, 113 wildcats were drilled. New discoveries, extensions and a reappraisal of discoveries made in 1939 will not approximate over 50,000,000 bbl., as against an estimated withdrawal during the year of 224,000,000 barrels. Demand in terms of crude for 1940 was 632,000 bbl. per day as against 626,000 bbl. per day for 1939. Demand for gasoline was the same as in 1939, but the demand lor fuel oil increased 3.8 per cent. Compared with 1939, Japanese shipments decreased from 75,786 bbl, per day to 61,000 bbl. per day, but the balance of Pacific foreign shipments increased from 59,409 bbl. per day to 61,304. Total with-drawals from storage during the year will approximate 7,000,000 bbl., almost all of which is fuel oil. Drilling activity was slightly greater than in 1939 and accounted for 890 new producing wells as against 851 for 1939 (Table 3). Production averaged 611,900 bbl. per day as compared with 614.,842 bbl. per day for 1939. The productive acreage figure of the state was increased by 4000 through discoveries and extensions. New Discoveries Los Angeles Basin District Del Vdle Field.—Northwest of Newhall, where the first oil well in California was drilled, R. E. Havenstrite completed his Lincoln No. I well, flowing 390 bbl. of 50" gravity oil together with 7000 M CU. ft. of gas. Later the well was recompleted, after cutting off the gas, for 950 bbl. of 34" gravity oil. The type of structure from which this production is coming is a plunging anticline, complicated by faulting. The Lincoln No. I well uncovered approximately 180 ft. of net sand. This field contains a gas cap and its indicated productive area approximates 500 acres. An intensive wildcat drilling campaign is expected during this coming year in the district in the vicinity of the Del Valle field. Extensions and Deeper Sand Developments Los Ange1es Basin District Athens Field.—On the northwest plunge of the Athens structure, the Thorley Oil Co. completed its No. 12-1 well, flowing 250 bbl. of 3 2" gravity oil from a depth of 8097 ft. The area in which the well is located is complicated by faulting and it is impossible at this date to determine the importance of this deep-zone discovery.

Jan 1, 1941

By R. R. Joseph, K. A. Gschneidner

The solid solubility of magnesium in the close-packed modifications of lanthanum, cerium, praseodymium, neodymium, gadolinium, dysprosium, and lutetium was determined from approximately 250°C to the eutectoid temperature by the X-ray parametric technique. The maximum solubility at the eutectoid temperature was found to be 9.4 at. pet in La, 8.2 in Ce, 9.2 in Pr, 8.2 in Nd, 14.1 in Gd, 13.5 in Dy, and 11.5 in Lu. The solubility when compared at a homologous temperature was found to increase in a smooth manner with decreasing size factor from lanthanum to lutetium. It was found that the apparent atomic radius of magnesium when dissolved in the lanthanide solvent was constant and could be accounted for by consideration of several models dealing with departures from Vegard's law. The eutectoid temperatures for the lanthanide-rich La-Mg, Ce-Mg, and Nd-Mg systems were found to be 544", 505°, and 551°c, respectively. A study of the solid solubility of magnesium in the lanthanide metals was initiated because the valency and electron egativity difference are essentially constant and favorable for solid-solution formation, and thus one could examine the effect of size on terminal solid solutions. The size factors based on metal radii range from 14.6 pet for lanthanum to 7.5 pet for lutetium. Since the electronegativity difference is small, 0.06 unit or less, application of the Hume-~othery' and Darken and Gurry2 criteria for solid-solution formation indicates that the solubility of magnesium would be expected to be small for lanthanum (between 5 and 10 at. pet) and to increase as we proceed along the lanthanide series. A search of the literature revealed no data on the solubility of magnesium in the lanthanide metals except for the solubility of magnesium in cerium at 450oCA typical phase diagram for the lanthanide-rich end of the lanthanide-magnesium phase diagram is shown in Fig. 1. EXPERIMENTAL PROCEDURES Preparation of Alloys. The lanthanide metals used in the preparation of alloys for this investigation were prepared from the corresponding fluoride by metallothermic reduction techniques previously described by Daane.4 The chemical analyses of the metals used are listed in Table I.

Jan 1, 1965

By Scott Turner

MY YEAR OF SERVICE as president of the A.I.M.E. came at a time when the mineral industry had suffered severely because of disturbed economic conditions throughout the world. The Institute, an integral part of this industry, had been similarly affected. Its membership and revenues decreased; it was confronted by problems of retrenchment at a time when its vigorous operation was especially important to its members, of some moment to the mining industry, and of value to the nation. Throughout the last year, the recession of activity in our industry continued with slight abatement. Your Board accordingly exercised such economy within the Institute as was possible without impairment of essential functions. It endeavored to aid in sustaining the morale of members, their sense of professional unity, and their interest in maintaining research and the interchange of scientific and technologic data upon which the progress of our industry depends. Effort was made to assist in the difficult task of finding employment for needy members; our endeavors have met with some success.

Jan 1, 1933

By W. C. Phalen

The production of salt in the United States divides itself at the outset into two distinct classes…

Jan 1, 1915

By William B. Millar

IN ONTARIO development of the gold mines is being rapidly pushed, while the intensity of the search for new mines has probably not been equaled at any time in the past. Even to outline the results of recent prospecting activity in Ontario would be a big undertaking, but it would be timely and, I hope, interesting to Institute members to review some generalities regarding the work of the prospector and then to discuss in some detail the growth of Ontario's most promising prospect area, the Swayze district, where serious mining operations are already under way. Probably no one writing about prospectors and pros¬pecting can resist hoping that his article will not reach the eyes of a certain portion of the uninformed general public and cause a further influx of "prospective prospectors" into any given area. It is somewhat mystifying how so many people reach the conclusion that prospecting is in

Jan 1, 1933

By Lewis Robert M.

The importance of phosphate in feeding the people of the world has been recognized by mining companies as they continue their search for new ore deposits and ways of improving phosphate production. An extensive phosphate-recovery research project involving investigation of beneficiation variables by batch testing, flotation pilot-plant processing of the major portion of the ore, gravity separation of the coarse fraction, and recovery of byproduct heavy minerals of a North Carolina phosphate deposit has been completed. Data obtained through batch tests enabled the development of an economical flowsheet which proved successful for the efficient recovery of a good quality phosphate concentrate in a pilot plant.

Jan 1, 1975

By Tomek Ulatowski

INTRODUCTION In 1974, Industrial Miners Mexico, S.A. (IMMSA), agent for the borrowers, was the largest privately-held mining, smelting, and refining company in Mexico (accounting for 32% of Mexico's nonferrous metal and coal production in 1974), the fourth largest company in terms of sales, and the second most profitable company in Mexico, excluding government wholly-owned and operated industries. The company was engaged in the mining, smelting and refining of coal, copper, fluorite, gold, lead, silver, zinc and related by-products for domestic consumption and export. A combination of favorable factors led IMMSA to propose an investment plan amounting to US$286 million for 1974 through 1978, of which US$150 million was to be financed. These factors included: Substantial profits in 1973 and 1974 Positive near-term outlook for metal prices Success of the reinvestment program in increasing productivity Substantial additions to proved reserves during 1973-1974 and Fiscal incentives provided by the Mexican government to stimulate investment in the mining industry. The primary purpose of the investment program was to construct a new electrolytic zinc refinery and to expand and modernize many of the company's existing mining and refining facilities. THE BORROWER Company History Compania Miners Mexico, S.A. was incorporated in the city of Monterrey in 1918 as a wholly-owned subsidery of ASARCO Inc. (formerly American Smelting and Refining Company, New York) for the purpose of mining and processing non-ferrous metals and related products. In compliance with the Government's Mexicanization program, ASARCO Inc. divested itself of 51% of its equity in Compania Miners Asarco, S.A. on June 30, 1965. Subsequently, ownership in the divested share was apportioned as follows: 15% ownership in Compania Miners Asarco, S.A. to a group of private investors, and 36% in trust for subsequent public sale. The company's name was changed to Asarco Mexicana, S.A. in 1965. Mexican ownership in Asarco Mexicans, S.A. was increased to 51% in 1967, following the purchase of the 36% share ownership held in trust, and then to 66% in 1974 when ASARCO Inc. divested itself of an additional 15% of its holdings in Asarco Mexicans, S.A. Following its 1974 divestiture of 15% of Asarco Mexicans, S.A., ASARCO Inc's ownership in Asarco Mexicana, S.A. was reduced to 34%. In 1974, the company changed its name for the second time to Industrial Miners Mexico, S.A. (IMMSA). Fiscal Agreement IMMSA entered into a fiscal agreement with the Mexican government in 1969. The agreement, which was renewed in 1974, provided for 100% of the production and export tax corresponding to the federal government with a minimum of 50% of the amount refunded to be reinvested in fixed assets. Further, the agreement permitted the company to

Jan 1, 1985

Secretary of the Interior, Franklin K. Lane, has appointed a commission of five mining and metallurgical experts from the Bureau of Mines and the Geological Survey to visit Europe to observe and study reconstruction methods in the devastated regions of France and Belgium. The chairman of the commission is Dr. Frederick G. Cottrell, chief metallurgist of the Bureau of Mines. The other members are: George S. Rice, the chief mining engineer of the same bureau; Frank H. Probert, consulting engineer of the bureau, and. professor of mining in the University of California; F. J. Cameron, consulting chemist of the bureau and expert on potash matters; and Hoyt S. Gale, of the Geological Survey, another expert on potash.

Jan 4, 1919

By R. F. Rolsten

VAN Arkel 1 prepared ductile tantalum by the thermal decompoiition of tantalum pentachloride on a resistively heated wire (2000° C) in an evacuated bulb maintained at 100°C. Burgers and Basart2'3 observed the formation of a mixture of tantalum carbide and free metal when a carbon deposition base was used. campbel14 suggested the thermal decomposition of the iodide if a lower decomposition tem- perature was desired. To date, the details for preparing high-purity iodide tantalum have not been disclosed. EXPERIMENTAL The tantalum to be purified was symmetrically placed around the clear quartz deposition surface centrally located within a 64 mm cylindrical Vycor bulb. The deposition vessel usually employed5 was modified6 by incorporating a reentrant fin,mer in place of the customary metal filament in the head

Jan 1, 1960

By C. O. Lee, Z. W. Bartlett, R. H. Feierabend

The Grand Isle sulfur mine is located in the Gulf of Mexico, approximately seven miles off the coast of Grand Isle, Jefferson Parish, La. The deposit is on acreage covered by oil, gas, and mineral leases originally issued in favor of Humble Oil & Refining Co. by the State of Louisiana which were continued, maintained, and redesignated by the U.S. Department of the Interior after passage of the Outer Continental Shelf Lands Act. The sulfur deposit was discovered in 1949 when Humble Oil & Refining Co. penetrated more than 200 ft of sulfur-bearing limestone in a zone between 1813 and 2075 ft below sea level. In 1954, Humble drilled ten more sulfur prospect holes, eight of which encountered sulfur ore. On September 19, 1956, Freeport Sulphur Co. acquired from Humble Oil & Refining Co, the sulfur rights underlying the tracts, and the actual design of the installation began the same month. The first structural contract was awarded in December 1957 and offshore erection began in June 1958. The initial phase of construction has been completed and production by the Frasch process commenced in April 1960. The estimated total cost of the project is $30 million, of which $8 million is the extra cost incurred by the necessity of offshore operations. More than $22 million was expended before production was started. GEOLOGY OF DEPOSIT Grand Isle is the third largest sulfur deposit in the U.S. The orebody embraces several hundred acres, but its outer limits are yet to be defined to the northeast, east, and south. Most Gulf Coast sulfur deposits occur in a caprock mantle of calcite (referred to as limestone), anhydrite, and occasionally gypsum, which covers the apex of an intrusive mass of salt. Commercial quantities of sulfur are usually confined to the calcite or limestone member. Most often such limestone is completely enclosed by dense anhydrite below and impervious sediments above, which effectively form a closed reservoir. The depth of the Grand Isle orebody ranges from 1800 ft to 2500 ft below sea level. Within the present boundary, the sulfur-bearing limestone varies in thickness from 220 ft to 425 ft, while the sulfur content varies an average of about 15 pct in the leanest hole to an average of about 30 pct in the richest. Rock containing less than 5 pct sulfur is not classed as ore, and holes assaying less than 20,-000 long tons per acre of sulfur in place are not considered commercial offshore. The sulfur enrich-

Jan 1, 1961