Search Documents

T. T. READ, Secretary of the Committee on Industrial Organization, presents the following very interesting monthly ad interim report: Reports from London are to the effect that 750 housing schemes for workers, involving the erection of 128,000 new dwellings, have been submitted to the Local Government Board. Birmingham alone needs 14,000 new houses, and the Housing and Town Planning Committee of the City Council considers that 5000 new houses must be built each year for the next 20 years. Nine hundred acres of land has been acquired, on which to build 10 to 12 houses per acre for the next two years. The town of Dudley, which built 300 modern dwellings in 1915-1916, submitted schemes for another 500 houses. There is a shortage of building materials required, specially brick. Financial assistance has been received for reopening brick yards that were closed during the war. W. E. Dickson, vice president of the Midvale Steel & Ordnance Co., is reported in the daily press as stating that his corporation is planning to spend $8,000,000 in improving its plant and assisting its employees in building their own homes. The company will advance 90 per cent. of the cost of the house and extend payments over a period of 12 years. Methods of work employed in building 256 houses at Quincy, Mass., for the workers of the Fore River shipyards are described, by Joseph Meltzer, in the Engineering News Record for May 29, 1919. The approximate cost was about $3500 per house, not including water supply, sewers, streets, and sidewalks. "Comparative Costs of Tenantry and Home-Owning;" "A Plain Talk on Helping Home-builders;" and "More Plain Talk on Home Building" are the titles of three publications of the Information and Education Service of the Department of Labor. These publications should be' of a good deal of service in convincing employees that it is to their interest to own their homes rather than to live in rented houses. The same Service has issued pamphlets discussing the cost of materials.

Jan 7, 1919

By Robert E. Green, T. Hinton

The velocities of the three possible modes of elastic-wave Propagation have been calculated for single-crystal aluminum at 1-deg intervals throughout the standard steveographic triangle. The results are presented as isospeed contours. The deviations between the direction of maximum energy propagation and specirzen axes are presented as arrows drawn within the standard triangle. The orientation factors associated with dislocation nzotion on the primary slip system only and also on all twelve slip systenzs have been calculated for all three elastic waves. The orientation factors associated with a longitudinal standing--7aue resonant specivnen hazle also been calculated. The relevance of these results to ultrasonic attenuation measurements is discussed. DUE to the widespread use of ultrasonics in the investigation of the properties of solids a number of authors15 have discussed in detail the theory of elastic-wave propagation in solids. In this paper the modes of wave propagation are evaluated according to the procedure suggested by reeen' for the case of single-crystal aluminum at 1-deg intervals throughout the standard stereographic triangle. The wave speeds are presented in the form of contour diagrams within the standard triangle. The deviations between the direction of maximum energy propagation and the normals to the wave fronts are presented as arrows drawn within the standard triangle. The orientation-de pendent factors (orientation factors) associated with dislocation damping as derived in the preceding paper6 have been calculated for the case of aluminum at 1-deg intervals throughout the standard triangle. The orientation factors for dislocation motion on the primary slip system only and on all twelve slip systems are presented in the form of contour diagrams, for both the traveling- and the standing-wave conditions. The relevance of these results to ultrasonic attenuation measurements is discussed. ELASTIC-WAVE PROPAGATION Three waves can be propagated in a linear elastic homogeneous anisotropic medium. The velocity of propagation v of each of these waves in a medium of density p can be obtained from the determination of the eigenvalues and eigenvectors of the matrix equa- The A's are a series of moduli which are functions of the elastic constants cij and the direction cosines 1, m, and n of the specimen axis. In the case of cubic single crystals where there are only three nonzero elastic constants cll, c12, and C, the A's are, The solution of Eq. [I] will give the wave speeds (eigenvalues) and the direction cosines a, 0, and y of the particle displacements (eigenvectors). To obtain the direction of maximum energy flux requires the calculation of the energy-flux vector ET with com- w is the angular frequency, A, the amplitude, and v the velocity of the wave. The direction cosines a, b, and c of the energy flux vector are then given by

Jan 1, 1967

By Merrill F. McCarty, Robert S. Olson

New organic flocculants of high-molecular weight are replacing lime, glue, and starch in liquid- solid separation. Of these synthetic materials, polyacrylamides are outstanding. Polyacrylamides form a class of compounds varying widely in composition and activity. Separan 2610H, one of the first of these flocculants' released to the mining industry in 1954, is described' as a high- molecular weight polymer of acrylamide with or without a copolymer material and with some replacement of amide by carboxylic groups.

Jan 1, 1959

TO THE BOARD OF DIRECTORS AND MEMBERS Of THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS GENTLEMEN Submitted herewith are the reports of the Treasurer for the year 1947 and the reports of the following standing committees Membership, Admissions, Papers and Publications, MINING AND METALLURGY (Magazine), and Library 75th Anniversary Celebration The founding of the Institute at Wilkes-Barre, Pa, in 1871, vas appropriately commemorated by a three-day Celebration, March 17, 18 and 19, 1947, at The Waldorf-Astoria, in New York City The Celebration had been scheduled for the preceding September but had been postponed, perforce, because of conflict with meetings of the Assembly of the United Nations The Celebration immediately preceded the Annual Meeting which was deferred from the usual February dates The proceedings took the form of a "World Conference on Mineral Resources " More than three thousand people, including eight hundred ladies, participated in the proceedings in one way or another Twenty-eight foreign countries were represented, some of them by five or six individual delegates Likewise, official representatives were designated by fifty institutions of higher learning in the United States A special 820-page Anniversary Volume entitled "Seventy-five Years. of Progress in the Mineral Industry,".(which

Jan 1, 1952

By R. T. Hukki

The purpose of this paper is to present an analysis of the unit operation of grinding and the circulating load, of the unit operation of classification and the circulating load, and of the two superimposed into one operation to clarify the overall trend of events relating the circulating load to the capacity of the closed circuit grinding system, to the specific surface area of the final fine product, and to the energy consumption in the closed circuit grinding process. The capacity of the closed circuit is frequently, if not always, determined by the classifier, not by the mill." With these words a startling idea was expressed in 1934 by Dorr and Anable.1 Today, some 30 years later, grinding in closed circuit is universally accepted. The basic curve presenting the capacity factor versus circulating load by Dorr and Anable has obviously been so convincing that not a single authoritative investigation regarding its validity seems to have been conducted. The only major subject of discussion appears to have been the relative merits of the 'high' and 'low' circulating loads. It seems to be universally agreed that much still remains to be hoped for regarding sharpness of classification. BASIC CURVES FOR CONSTANT MILL LOADING Fig. 1 presents a series of basic curves for constant mill loadings in function of new feed rate and circulating load. The mill loading indicated by each curve is the sum of hourly tonnages of new feed and circulating load. For example, at point 0 where the new feed rate is 100 t/h and the circulating load 300%, or 300 t/h, the mill loading is 400 t/h. In closed circuit grinding, the new feed rate corresponds to the rate of finished classified material produced. Although at this stage the effect of classification is excluded in construction of the basic curves, the trend indicated by these curves is strongly in favor of closed circuit operation under relatively small circulating loads. A study of the curves reveals that, e.g., a mill operating under a load of 200 t/h at point P where the new feed rate is 50 t/h and the circulating load 300% will also operate under the same total load at point Q where the new feed rate is 100 t/h and the circulating load 100%. In other words, a reduction of circulating load from 300% to 100% would lead to doubling of the new feed rate and doubling of the rate of production of finished material, without a change in the total mill loading. The obvious question is, is it also possible by a reduction of the circulating load in a closed industrial grinding circuit to increase the production of finished classified material and, if so, how and to what extent? GRINDING TESTS BY DORR AND ANABLE In a series of open circuit grinding tests reported by Dorr and Anable1 limestone was ground at various feed rates in a 3-ft ball mill. The original data are reproduced in Table I. It can be seen that with the increased feed rate production of -65-mesh material increased and the energy consumption per unit weight of the -65-mesh product decreased in the reverse ratio. The data shown in Table I have been reproduced for our purposes in Table II for a scale corresponding to grinding in a large industrial mill. This reproduction

Jan 1, 1968

By Erminio Ferraris

The development of the mining industry in Sardinia dates from the application of the mining law of 1859, which, following the example of the French mining law of 1810, declared prospecting to be free, and suppressed the liens which had previously attached the mine to surface ownership. The first ore-dressing plants were installed by German engineers upon the classic models of the Harz and of Freiberg; but in 1880 Sardinia commenced to open a new path in that industry, utilizing the refuse from the mining of rich, selected minerals, of poor deposits, and of mixed ores. The first experiments were attempte to adapt the existing apparatus to local conditions, but progress was rapid, as was demonstrated already in 1887 by the calamine-dressing mill of Monte-poni, which exhibited a large plant designed in accordance with the experience gained, and constructed entirely in the machine-shops of the country, after new models and designs.' This example was followed two years later by the Sociékté Malfidano, with a large plant of the same sort, and with the reconstruction of the old-fashioned dressing-mill, built in 1880 by the Austro-Belgian Company. In 1900, almost all the mines of Sardinia had adopted the new designs, and the island contained 32 concen-trating-works, employing 2,000 h.p. and 1,924 workmen. Since that time, there have been added a large dressing-mill for blende at Gennamari, and two for calamine, at San Giovanni and at Masua, while the establishments at other mines have been enlarged and perfected. For the treatment of intimately mixed ores, a large establishment has been built upon the new

Jan 1, 1909

TWO American students entered the École des Mines in 1856, Joseph Lesley of Philadelphia and Thomas Egleston of New York. Lesley remained there only one year, but Egleston completed the whole curriculum and received, in 1860, the certificate given to foreign students in lieu of the official appointment and degree awarded French students. Returning home he received, in 1861, an appointment by Secretary Henry of the Smithsonian Institution to sort, label, and arrange the collections of mineralogical and geological specimens which had been brought to Washington by the various government exploring expeditions in the West. Thomas Egleston, born in New York City on Dec. 9, 1832, was the son of Thomas Jefferson Egleston, who came to New York from Massachusetts some time before 1829. The first American ancestor of the family had settled near Dorchester in 1630. T. J. Egleston and Joseph Battell established an iron-merchandizing business* at 166 South St., New York, which prospered exceedingly; so much so that when Thomas J. Egleston died, July. 12, 1861, his estate had a book value of over $500,000. Since an older brother was expected eventually to take over this business, Thomas, who had a liking for science, went to Yale, where he completed the regular four-year course in 1854, and then remained another year for advanced work in chemistry under Silliman. One biographer says he went to Europe, early in 1856, on account of his health. It was the custom at that time for wealthy young men to make a tour of Europe after completing their academic education. Whatever the precise reason, he began scientific work at the Jardin des Plantes in Paris but soon trans-

Jan 1, 1941

GENTLEMEN Submitted herewith are the report of the Treasurer for the year 1938 and reports for the same year of the following standing committees: Admissions, Membership, Papers and Publications, Mining and Metal¬lurgy (Magazine), Library, Speakers for Local Sections and Student Societies, and Student Relations. To these reports members are referred for further details. Membership.-The end of the year 1938 saw Institute membership at an all-time peak: 12,474, made up of 2898 Student Associates and 9576 members of other classifications. The next highest level had been reached at the end of 1921 when corresponding figures were: total, 10,329; student members, 1450; all other classifications, 8879. The net gain for the year was 1495, of which 751 were Student Associates and 744 in the other categories. Two factors contribute to the growth of membership: (1) the enrolment of new members; and (2) the retention of members already on the roll as reflected in a relatively small number of resignations and suspensions for nonpayment of dues. For the first, much credit goes properly to the general Membership Committee that functioned for a second year under the chairmanship of Clyde E. Williams. With the cooperation of Institute members in general, to whom Mr. Williams expresses appreciation in his report, the Committee has been successful in acquainting eligible nonmembers with the purposes, activities and advantages of the Institute. The result has been the receipt during the year of 1162 applications, exclusive of Student Associates. This compares with 1212 during 1937 and 1266 during 1936. However, in considering this modest decline, account must be taken of the somewhat less prosperous conditions prevailing in the mineral industries and, consequently, among engineers engaged ?in those industries.

Jan 1, 1939

By Frank Hall

THE needs of the World War showed the necessity of a metal stronger than cast iron which would supplement the supply of steel. So patriotic metallurgists were spurred to new efforts to improve the status of that half-breed of the metal world that had been, more or less erroneously, christened semisteel. As a result, it was developed that for certain purposes semisteel was superior to steel in the manufacture of shells. Steel, because of its greater strength and toughness, is able to carry a greater charge of explosive, weight for weight; consequently, a steel shell can be expected to cause greater destruction when used against fortifications or other inanimate objects, while semisteel, because of its comparative brittleness and its resulting greater fragmentation, is capable of inflicting more serious loss of life when used against opposing forces of men. Therefore, each has its proper place in the economy of war. For the present purpose, steel may be defined as a comparatively pure iron whose physical nature is modified by small amounts of carbon, silicon, sulfur, phosphorus, manganese, and possibly other rarer elements; while cast iron generally is limited to approximately 93 per cent. of iron, the remainder consisting of larger percentages of carbon, silicon, sulfur, phosphorus, and manganese. Semisteel may be defined as cast iron in which the carbon and silicon have been reduced to as low a point as is consistent with maintaining the nature of gray iron, and in which the remaining elements are manipulated so as to give the greatest strength.

Jan 1, 1920

OFFICIAL INSTITUTE REPORTS FOR THE YEAR 1924 Report of the Secretary TO THE BOARD OF DIRECTORS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS Gentlemen -To a Board of Directors keeping in as close touch with all of the affairs under their care as do the Directors of the A -I M. E, through their monthly meetings, a report of the year's progress is almost superfluous To the members who read the monthly reports of the Board Meetings and of the various activities of the Institute as published each month, a yearly report cannot carry much fresh infor¬mation, yet for both it may be well, as is the custom, to glance over the field of our activities during the past year, and to make an estimate for the year to come The beginning of 1924 was not propitious for the members of the mining profession, though tonnage, production for 1923 had been high and the gross value higher than for several years The margin of profit had been narrow, prospecting and development were limited, and many of our members were unemployed or were working in other industries Toward the end of the year, higher metal prices were in sight Old-time optimism began to grow, and it now brightens the outlook for 1925 An excellent barometer of the prosperity of the industry, and that of the Institute, for they go hand in hand, is the work of our Employment Bureau During the past few months, the percentage of our members for whom openings have been found has been increasing to a marked extent, and many members who had fallen in arrears are placing themselves in good standing The number of new members joining has remained about as it was in 1922 and 1923 The Directors have reason to congratulate themselves on the interest maintained during a dull period, for it is not humanly possible to take a keen interest in the technology of an industry when our hands and minds are not actively engaged in it Now, with a much brighter outlook, we can look forward to a year of increasing prosperity for the industry and for the Institute

Jan 1, 1923

By T. R. Braithwaite

The brief comments made in this chapter deal mainly with shaft sinking, but don't assume that freezing techniques apply only to shaft sinking. They can be used on tunnel work, on such things as liquid gas storage in sediment, and I think you will probably see other applications for it as we go along. The method was first developed in 1883 and was used to sink shallow shafts through water-bearing overburden in Germany and in England. One of the early shafts was in Germany and was sunk by freezing to 310-ft depth. The project required 17 months for drilling, roughly 5 1/2 months for freezing, and another 7 months for sinking, giving an average progress of 10 ½ fpm. Fortunately there have been numerous improvements and new developments in this technique through the years. With equipment and techniques available today, we can take a 20-ft-diam shaft down through 2000 ft of water-saturated overburden and the time schedule runs roughly 4 months for site preparation, freeze-hole drilling, installing the casings, and setting up the plant; 4 ½ months for freezing; and 6 months for excavating and installing permanent linings. This gives a progress rate of about 140 fpm, on average. I might qualify that a little in that the special linings that are required for some formations can affect the time. If it's straightforward sinking where one can use a heavy concrete lining, up to 630-640 fpm may be achieved in a shaft; but with special cast-iron tubbing or types like that, 5 fpd is pretty good progress, so the lining does affect the time. The freezing method is used mainly for sinking shafts through unstable water-bearing formations which cannot be grouted either effectively or economically and which are too deep to enclose in pile casing. Even with overburden, grouting methods available today can handle roughly 100 lb water pressure; in the range of, say, 100 to 150 ft from the surface, it's very often best to grout 40 or 50 ft. You normally drive a pile casing and go through it. Below that range, freezing is very often the economical

Jan 1, 1970

By Donald B. Gillies

The fundamentals of human nature don't change much from generation to generation, or even from century to century. Except for the spur of necessity and the lure of reward and ad venture, few of us would bestir ourselves unduly. The general welfare has little appeal to the average individual. Its promotion comes about mainly as a by-product to individual efforts directed at more personal benefits and satisfactions. In discussing incentives for the mining industry, we really are talking about incentives for people who devote their energies and resources to mining. The vigorous and productive mining industry as we have known it was the product of the varied incentives we have known in the past: the lure of great financial reward if you struck it rich; the thrill of romance and adventure in the search for mineral wealth, usually along the frontiers 'of civilization; the satisfaction of developing a great, productive enterprise by the application of skill, courage, and determination in the face of obstacles. Back of the prospector and engineer were other venturesome persons willing to take a flyer with their savings in a grubstake, or in stock in a promising mining venture, hoping for large returns, but reconciled to take a loss and try again with the next opportunity. It is free enterprise-a chance for high profits, but a chance also of total loss-that created the great mining industry of this country and of the world. Free enterprise has given us, in the United States, the greatest productive system in the world, the highest standard of living, the most abundant life. The lure of gold-whether from the ground or merely incidental to the discovery and development of our mineral resources-pushed our frontiers westward across the country and northward into Canada and Alaska far in advance of the staid course of agriculture and commerce. No one guaranteed success to our forebears as they risked life and fortune in developing a new country. Self-reliance was the backbone of our economic and spiritual Progress and achievements. Our neighbors had little time to spare from their own problems. And though there was a willingness among the pioneers to help one another, they didn't lean too much on one another.

Jan 5, 1950

By James A. Barr

[CONTENTS PAGE Foreword. By JAMES A. BARRI A New Core Barrel for Prospecting for Phosphate in Florida. By I. M. LEBARON 2 Prospecting for Phosphate in Tennessee. By W. F. GUENTHER 6 Machine Prospecting in Tennessee Brown Phosphate. By H. O. PICKARD, JR8 Diamond Drilling through Flint Horizons in Tennessee. By HENDON R. JOHNSTON9] Foreword PROSPECTING methods used in Tennessee have gradually improved with the years, as required by depletion of the easily accessible and shallow deposits and the universal trend toward mechanization, and as necessitated by exploring deeper beds, often occurring under limestone and flinty overburden. In the early days it was a very simple matter to dig pits by hand, using a plentiful supply of local farm labor to expose relatively shallow deposits of "brown rock" under shallow clayey overburden that would stand up without timbering. Visual inspection of the exposed phosphate and expert judgment of the"grade" analysis, aided by a "biting" test to reveal presence of unwanted silica, furnished most of the information required. All this might be helped by a few samples sent to the local chemist[t] who supplemented his income by judicious trading or tanning a few bear skins. The extra curricula activities did not affect the accuracy of the analysis which hold up even under present day standards. Some shot and core drilling was done in Hickman County, mostly for the limestone-like blue Phosphate deposits. The next step was the use of a 4-in. posthole auger, hand operated as described by Guenther, followed by- a completely mechanized rig, as described by Pickard. Both these methods are practically adapted to the prospecting of the relatively soft brown rock deposits at moderate depths of clay overburden. For prospecting in areas of deeper overburden, such as are often found in Hickman County, up to 150 or even 200-ft depths, a modified core-drilling method is described by Guenther. Johnston describes a special diamond-drilling technique, developed by TVA, to penetrate flint horizons, which was adopted by the International Minerals and Chemical Corporation to prospect in Hickman County where deposits had previously been prospected at considerable expense and with difficulty, by Small, temporary, hand-dug shafts.

Jan 1, 1947

By R. S. Shoemaker

Mines are closed for two reasons; exhaustion of ore or insufficient price for the mineral. On the other hand, the reopening of an old mine can be the result of any one of three events; the discovery of more ore, a sudden rise in the price of the product or the use of a new low-cost method of mining or milling the ore. Examples of the latter would be the open-pitting of an orebody previously mined underground as recently happened at Tyrone, N.M., or the adoption of acid leaching of an old pit as has been done at Miami, Ariz. The unique native copper mines of the Keweenaw Peninsula of upper Michigan have not been so fortunate. These deposits, which were first worked by prehistoric Indians, have been mined continuously from the early 1840's to 1968 when the last mines of Calumet and Hecla were closed and the Ahmeek mill. still using eight Nordberg steam stamps, was shut down. There are two types of deposits from which native copper is obtained; amygdaloid, which is a lava flow, and conglomerate, a sedimentary deposit of sand, rock fragments and pebbles cemented together. "In the amygdaloid, the copper is disseminated, or distributed much like the raisins in a cake; but in the rich Calumet conglomerate, the copper is more like a malleable rope or thread cementing the pebbles together." (C. Harry Benedict. Red Metal: The Calumet and Hecla Story, (Ann Arbor, Michigan, 1952), p. 42.) These deposits produced almost all of the copper used by the North in the Civil War and were substantial contributors to the copper needs of the United States in both World Wars. Some were mined to depths of as much as 9500 ft along the dip of the vein structure and 7500 ft vertically. Few of the mines ever really became worked out, but became uneconomical because of depth, pinching of veins or grades which dropped to about 1%.

Jan 5, 1972

By Gerald V. Jergensen

Does an idea have merit? What does it cost to implement? Can the concept be implemented successfully? The ultimate proof is to try, then see. However, when there are many millions of dollars at stake, blindly building and trying requires considerable courage. Owners and investors in retrospect might choose other less complimentary words. So we might ask, "How might we establish the feasibility of an idea or concept before committing large sums of money to the ultimate test?" From this basic and prudent question, has evolved the engineering concept of the feasibility study. A feasibility study is simply a systematic evaluation of an idea or concept to determine the prospects for success. In a literal sense, a feasibility study considers an idea in terms of its data base, "builds" the idea on paper, "operates" that idea, calculates the cost and benefits, then measures the probable success in terms of some economic, technical or financial standard. Feasibility studies can be quite modest in scope yet provide useful insights as to the viability of an idea. A study might be initiated only to examine the completeness or validity of the metallurgical data base. Another study could be a search for a workable idea or solution to an already-identified possibly troublesome problem. In this latter case, the question, "Will it work?" may be far more important than, "How much will it cost?" Feasibility studies are sometimes global in scope, involving several dozens of specialists and examining an entire "grass roots" mining complex. Other studies may be less ambitious but equally important in examining an expansion proposal or developing new operating techniques. Studies may be commissioned to remove plant bottle-necks, solve maintenance problems and so on. The terms study and feasibility study are used interchangeably in this chapter. They denote a systematic method to examine a proposed concept or idea. DATA BASE Typically, studies are initiated with a minimum amount of specific information and a maximum number of assumptions. As the work proceeds and the data base expands, assumptions are replaced

Jan 1, 1982

The following communication has just reached the Institute, from the office of the Provincial Geologist, Department of Lands,-Forests and Mines, Ontario, Canada: During the autumn of 1917 gold was discovered in unsurveyed territory south of Lake Abitibi in northeastern Ontario. This area lies about 70 miles almost directly east of the well known Porcupine area. During the coming summer, the Ontario Bureau of Mines is to make a geological survey of this new gold area. Following the custom of Ontario, this area is being divided into townships, 6 miles square. These townships have recently been given the following names in honor of men well known in the mining and geological world. In alphabetical order the names are as follows: Frecheville-Prof. Wm. Frecheville, Professor of Mining in the Royal School of Mines, London; Past President of the Institution of Mining and Metallurgy. Garrison-Mr. F. Lynwood Garrison, Mining Engineer, Philadelphia, Pa. Harker-Dr. Alfred Harker, F. R. S., immediate Past President of the Geological Society of London.

Jan 6, 1918

By A. A. Gustafson

IN diamond or churn drilling for the prospecting of ore bodies, two products can be used for quantitative analyses; i.e., the core and the cuttings, or sludge. Some operators prefer an assay of core; others insist that the sludge be sent for analysis. Both must recover the sludge for check samples or for assays if there is no core recovery for any particular section of the diamond-drill hole. The Freeport Sulphur Co. found that numerous cumbersome sludge boxes or barrels were inconvenient and delayed drilling. The sludge settled slowly in the ordinary shallow, rectangular diamond-drill boxes and its total removal from the container was difficult, time-consuming and unsatisfactory; and sampling of deposits of which the metal contents are easily concentrated, as in ores containing cinnabar, gold and silver, is subject to error if the boxes are not thoroughly cleaned. Mr. Charles Ballard, dredge superintendent at Freeport's operation at Grande Ecaille, Louisiana, developed a portable cone while he was in charge of prospecting a mercury property near Tonopah, Nevada, in 1040. Ballard later improved the design while the settler was being used at a manganese property in New Mexico. The operation is based on the "free settling" of comminuted particles in a quiescent liquid. The ordinary sludge box discharges over a lip 8 to 12 in. wide and consequently the water has sufficient velocity so that the discharge water is never clear. The cone settler used by Freeport Sulphur Co. discharges over the entire circumference, which gives a discharge lip of 9 ft. in the size of cone used at the cinnabar and manganese prospects. Consequently, the velocity of the discharge water is slow enough so that all fine material settles and the discharge water is clear. When the drilling of a sample interval is complete, the sludge can be drawn off by the time the driller is ready to cut another sample. Thus, only one cone is needed per drill. The cone has been used by Freeport successfully in churn-drilling a manganese deposit, in diamond-drilling a mercury deposit, and in diamond-drilling a deposit of ore containing tin, copper, gold and silver. The cone is greatly superior to the old methods of collecting sludge and is now used on all Freeport drilling campaigns in the western states, both for surface and underground drilling. Fig. I shows the important details of a cone designed for average operating conditions, 30 in. in diameter and 36 in. high. Abnormal conditions may require some revisions in design. Fig. 2 shows a working drawing. A hose or pipe larger than the one used to convey water from the pump to the swivel head of the string of rods is connected to the stuffing box at the collar of a diamond-drill hole. The usual T-connection is used. It is not necessary to use a stuffing box if the top of the cone can be placed lower than the collar of the hole. Then the return water and cuttings can be made to flow by gravity. This hose or pipe discharges the cuttings of the drill bit and the return

Jan 1, 1943

By Charles E. Wait

In the use of the apparatus purchased for the new chemical laboratories of the university, no piece has given us more satisfaction, or has been a greater success, than a new still which is the subject of this paper. In the designing of this still I had two definite objects in view ; one, the utilizing of steam from the large 60 horse-power boiler used in heating the building, and the other, a provision for making distilled water with gas, when steam from the heating-plant was not available. The still is encased in wrought-iron, with a lining of asbestos, and is provided with a float which automatically regulates the flow of water from the supply-pipe. It was made for me by G. J. M?rrle, Pforzheim, Germany, and was imported by Messrs. Eimer & Amend, of New York City. It is a beautiful piece of apparatus, and the workmanship is excellent in every detail. The essential parts of this apparatus will be understood by consulting the accompanying figures, but a few words of explanation may be appropriate. The still has a capacity of seven gallons, and is made of heavy copper, tin-lined. It has a water-gauge showing the height of the water in the still, also an exit for steam, and safetyvalve, V; inlet for steam through a coiled perforated block-tin pipe; also an outlet, 0, for cleaning out the still; and there is also a heavy

Jan 1, 1895

By MARK H. LAMB

(Canal Zone Meeting, November, 1910.) THE recent growth of a sentiment among cyanide-plant designers against the use of gravity-stamps for the crushing preliminary to cyanidation may be said to date from the almost simultaneous perfection of the ribbed tube-mill liner and of the tall, air-agitation tank. The first step in the resulting change of practice was the universal adoption of the tube-mill for fine-grinding and the use of coarse screening oil the battery. This was the beginning of the surrender of supremacy by the gravity-stamp ; since merely the single fact that it was a more economical machine for crushing fine had retained it in favor as compared with ball-mills, rolls, or steam-stamps. The surrender, however, is not yet complete. It is the universal practice to use rolls where a relatively small tonnage is to be crushed coarse, as, for example, when coarse concentration is included in the plan of treatment. Power, attendance, repairs, and first-cost are smaller for the rolls, under such circumstances, than for stamps; and it is becoming daily more apparent that, with no concentration to provide for, the use of rolls and tube-mills, without the complication of trommels and elevators required by concentration, is rapidly gaining favor in the eyes of the leading designers. The next step was the use of the rapid-running Chilean mill between the gravity-stamps and the tube-mill, which again narrowed the field of operation of the gravity-stamp while radically widening its screen-aperture. Such a combination of stamps and Chilean mill offers advantages when fine concentration is necessary, since the reduction in the Chilean mill call be adjusted easily and governed by varying the screen-mesh. But even concentration is now looked at askance. One of the leaders of this metallurgy has abandoned the separation and

Jul 1, 1910

By George Smith

THE discussion of production control at the Insti-tute's annual meeting was profitable in that it started some thinking. One pertinent question there raised was how the opening of new mines, whose now unneeded output would inevitably react on prices, could be postponed until the market was ready to ab-sorb their output. In transportation some restraint is being exercised on building new and unneeded fa-cilities, but in production no general solution of the problem has been offered. Yet in a special field of new development of increasing importance a quick and easy solution has been suggested. I refer to the leasing of mineral deposits on the public domain. The report of the United States Coal Commission says: "In its possession of approximately 60,000,000 acres of public coal lands the Federal Government has its own responsibility in restraining overdevelopment. The Department of the Interior, which has control of these lands under the leasing law, construes the law as giving the department no discretionary right to refuse applications for leases regularly made by qualified citizens or corporations for coal deposits on the pub-lic domain. It presumes, that the applicant believes there is a need for an additional coal mine in his local-ity and expects to find a market for the coal produced. Overdevelopment, however, is a fact in the West as well as in the East, and wherever present involves needless investment and excessive costs of operation. Plainly, the leasing law should be so amended as to give the executive department full discretion in its approval of the opening of a new coal mine on the, public domain, making that approval contingent on the showing that the new mine would serve the in-terest of the consuming public." A similar view of the Federal Government's re-sponsibility in restraining overdevelopment of its oil lands has been presented by the Federal Oil Conser-vation Board. The leasing law vests little or no dis-cretion in the Secretary of the Interior, who must grant a lease to a qualified applicant regardless of any obvious country-wide condition of surplus produc-tion. This wide-open invitation to exploit and dissi-pate the people's own oil resources could be restricted by simple legislation, although as remarked by the board, such a legislative remedy for a plain economic ailment "does not evoke popular support when its purpose is avowedly to put the brakes on development of natural resources."

Jan 5, 1928