Search Documents

By R. Schuhmann

Jan 1, 1965

By G. F. Butterworth

The metallographic structures most frequently encountered in rifle barrels, and which are illustrated by the accompanying photomicrographs, fall naturally into two groups, distinguished by the method used to, produce in the stock a physical condition having the requisite properties. The fist group consists of "rolled" barrels; that is, barrels subjected to hot working by rolling in or near the critical range. In the second group, the stock, which is smaller in diameter than the first, is upset to form the butt end and is then heat treated by giving it a quench and a draw. These barrels will be referred to as " heat-treated " barrels. The structure of the rolled barrels resembles closely that of the same steel after annealing. There is the same network of excess ferrite outlining the grain boundaries, but the grains themselves are composed of sorbite rather than pearlite. The grain size is closely related to the rolling temperature. The critical-point curves of this grade of steel, which is approximately 0.50 to 0.60 per cent. of carbon and 1.00 to 1.30 per cent, of manganese, show a single very pronounced point between 1300" and 1350" F. (704" and 732" C.). Barrels rolled within this temperature range give an exceedingly fine grain, shown in Fig. 1. In fact, the grains may be so fine that, at a low magnification, they may be confused with the heat-treated structure shown in Fig. 6. A magnification of 500 diameters, however, will always resolve a rolled barrel into the characteristic structure shown in Fig. 2. As the temperature is increased, the grains are found to be larger. If, on the other hand, the rolling temperature is below the critical range, the structure previous to rolling will not be obliterated, the only effect of rolling being to elongate the coarse sorbite grains in the direction of rolling, Fig. 3. This distortion is greatest at the muzzle. Heat-treated barrels are quenched in oil from above the critical range, which should give a martensitic structure, Fig. 4, but the presence of some troostite in the martensite is frequently noted when the quench has not been sufficiently drastic, Fig. 5. The structure brought about by the subsequent draw is not so striking, though quite as typical. It is sorbitic or sorbito-pearlitic, and under a low magnification appears almost homogeneous, as in the case of fine grains of pepper and salt well mixed together, Fig. 6. This structure is substantially the same for all

Jan 1, 1920

By H. L. Bridgman

The correct sampling of ores is a subject of far greater importance than is usually conceded to it. Of the little which has been published on this subject, the recent paper by Mr. Glenn, with the accompanying discussion by Dr. Raymond (Trans., xx., 155), is the latest and best, and well worthy the careful perusal of all interested in accurate sampling, whether by hand or by machine. It is doubtless true that thorough hand-sampling gives as good average results as can be obtained; but all hand-sampling is subject to the possible incompetency, carelessness, or dishonesty of the workmen employed. It is, moreover, tedious and expensive, requires large space, and usually entails considerable delay, both in unloading and in sampling. For these and other reasons, machine-sampling is now regarded with more favor than ever before. So-called machine-sampling may be accomplished in two radically different ways: 1. Part of the stream of material is taken for the whole time. 2. The whole stream of material is taken for part of the time. Under the first case the stream, as it issrles from the deliveryspout of the crusher, is cut continuously in any given proportion, such as one-tenth, one-fourth, or one-half, by some fixed apparatus, which, as it contains no moving parts, is strictly speaking not a machine at all, but may be termed an appliance. The principle under which these appliances operate is now pretty generally conceded to be wrong, becanse of the practical impossibility of' cutting such a

Jan 1, 1892

By Charles E. Wait

IT is said by some that the occurrence of a deposit of sulphide of antimony in Southwestern Arkansas has been known for fifteen or twenty years. Whether or not such is the case I am not prepared to say, but I am not able to find any record of such a discovery, or any analysis of antimony ore obtained from that section, published at so early a period. The present discoveries, that seem to be attracting some attention, date back to the winter of 1873-74. At that time a vein of ore was found by Mr. Robert Wolf, in honor of whom the vein was named, and still is called, "the Wolf lode." At the time of the discovery the ore was unknown to the prospector, and its composition was not thoroughly understood in that locality until samples were sent to several analytical chemists, who pronounced it sulphide of antimony-stibnite. Since the discovery of this ore there have been three mines opened, and a number of interesting minerals of the antimonial series have been found. I have had an unusually good opportunity to collect specimens from these mines; and it is owing to the constant inquiry concerning the character of these ores that I have collected for publication the results of quite a number of analyses, sufficient I trust to clearly point out their composition. This is one of the few localities in the United States where antimony ore is found in workable quantities; I say workable quantities, because two different shipments of ore have been made to English reduction works, and in both cases excellent returns were made. The discovery of these deposits will, it is hoped, give rise to a prosperous and remunerative industry at no distant day, and when fully developed they may yield ore in sufficient quantity to supply the regulus for the home demand, thus adding wealth not only to those interested, but also to the State of Arkansas. The three mines are situated in the northern part of Sevier County, and may be reached by the St. Louis, Iron Mountain and Southern Railway to Fulton, thence by wagon-road to Columbus, Nashville, Centre Point, and to the mines. During most seasons of the year the

Jan 1, 1880

By L. W. Pommier, F. B. Brien, A. K. Bhasin

In the field of mineral processing, although many operations are applied to suspensions of ore particles in fluids, there is a lack of fundamental knowledge relative to the flow resistance encountered by immersed bodies moving through solid-liquid suspensions. Previously proposed equations, based on the Ostwald-de Waele (power-law) model for non-Newtonian fluids, are exam ined in the turbulent flow region relative to a number of pertinent variables and their effects on the movement of immersed bodies. As more knowledge is acquired in regard to the effects of suspension variables on the rheological properties, useful relationships may be proposed to allow predictions of conditions to achieve optimum results for engineering purposes. In the field of minerals processing, many operations are applied to suspensions of ore particles in fluids. The differential movement of solids of various sizes and densities in suspensions is of utmost importance to gravity concentration, wet classification, flotation, hydrometallurgy, and pipeline transport of solids. The subject is also of importance to other branches of engineering; for example, those involved with soil mechanics, ceramic slips, and oil-well drilling fluids. There is a lack of fundamental knowledge relative to the flow resistance encountered by immersed bodies moving through solid-liquid suspensions. The problems encountered in the direct application of the well-known Stokes and Newton's Laws to non-Newtonian systems have been examined in a previous paper.' Equations were proposed based on the Ostwald-de Waele (power-law) model for non-Newtonian fluids. This present paper examines these equations in the turbulent flow region relative to a number of pertinent variables and their effects on the movement of immersed bodies. It is thought that, as more knowledge is acquired as to the effects of suspension variables on the rheological properties, useful relationships may be proposed to allow prediction of conditions to achieve optimum results for engineering purposes. The purpose of this paper is to make an initial assessment of the nature and magnitude of pertinent suspension variables. In order to avoid too voluminous a document, the examination of kinetics and mechanisms will be omitted at this time. THEORY A Newtonian fluid is defined as a fluid in which the stress is proportional to the rate of strain, 2 i.e.: H = viscosity; see Table I. for list of symbols The following equations are conventionally used to assess the motion of spherical particles moving under laminar and turbulent flow conditions through Newtonian fluids: When these relationships are applied in practice to suspensions, the liquid density is substituted by a composite suspension density, and viscosity is usually taken as that of the suspending liquid or an approximated "apparent viscosity." However, suspensions are non-Newtonian in character3 and thus, more than one viscosity parameter is required to describe their behavior. A number of models have been proposed for non-Newtonian fluids;2,4 among these the simplest is the Ostwaldde Waele or power-law model for incompressible fluids which for one dimensional flow may be reduced to:

Jan 1, 1970

By O. M. McRae

The Courtland-Gleeson area is in Cochise County about 15 miles east of Tombstone in southeastern Arizona. Rocks exposed in the area range in age from Pre-cambrian to Quaternary. The Precambrian is repre-sented by the Pinal schist. Paleozoic rocks include the Cambrian Bolsa quartzite and Abrigo limestone, Mississippian Escabrosa limestone, and the Permo-Carboniferous Naco Group limestones. Rocks believed to be of Triassic and/or Jurassic age include the Copper Belle monzonite porphyry, Turquoise granite, and Gleeson quartz monzonite. The Cretaceous is represented by andesitic volcanics and various sedimentary rocks. Tertiary rocks include the intrusive and extrusive Sugarloaf quartz latite porphyry and numerous dikes of various rock types. Quaternary conglomerates cover the northern and eastern part of the area. The geologic structure is extremely complex. All rocks as old as early Tertiary have been involved in either tilting, normal faulting, high angle reverse faulting, imbricate thrusting or folding and overfold-ing. Major deformation was initiated during the first half of the Tertiary. Northeast-southwest compres-sional forces caused thrust plates containing lower Paleozoic rocks to override Cretaceous rocks. Subsequently, two large slide blocks of lower Paleozoic rocks, acting under the influence of gravity, moved eastward. The imbricate structure and the gravity slide blocks were then broken by late Tertiary normal faults. INTRODUCTION The Courtland-Gleeson area, or Turquoise Mining District, has long been recognized as an area of extreme structural complexity. Gilluly 2 referred to the entire district as a "gigantic thrust breccia". In 1962, Bear Creek Mining Company completed a two year program of detailed geologic mapping supported by exploration drilling. The purpose of this paper is to present some of the results of this investigation and to provide a structural interpretation based on these results. The geologic map that accompanies this report is generalized and shows only the major and significant features. The area was initially mapped on aerial photographs on a scale of 1 in. equals approximately 500 ft. These data were transferred to a planimetric base using a vertical sketch master. LOCATION The Courtland-Gleeson area is in central Cochise County, about fifteen miles east of Tombstone, and about twenty-two miles northeast of Bisbee in southeastern Arizona (Fig. 1). The area is readily accessible over graded gravel roads from both Tombstone and Elfrida. GENERAL GEOLOGY Rocks exposed in the area range in age from Pre-cambrian to Quaternary. wilson3 and Gilluly2 have published very detailed descriptions of the principal rock units exposed in the area. Only a summary description is provided in Table I. A great number of previously unmapped narrow Tertiary dikes and small irregular masses of hornblende andesite porphyry, lamprophyre, and aplite intrude the Gleeson quartz monzonite in the western part of the map area. The scale of the map prohibits showing them. The aplite dikes are related to, and bear the same structural relationships as, the Sugarloaf quartz latite dikes found in this area. For that reason, and because both the hornblende andesite porphyry and the lamprophyre are post-mineral and post-thrusting, their omission from the map is not considered significant. Because so many of the contacts in the district are fault contacts, because bedding faults appear to be prevalent but are difficult to recognize and map, and because igneous intrusions are so common throughout the sedimentary section, it is virtually impossible to measure an exact total thickness of any of the sedimentary rock units. Nevertheless, neither the field mapping program nor the diamond drilling provided any basis for suspecting that the thicknesses of the sedimentary units are significantly greater or less than what might be inferred from surrounding districts.

Jan 1, 1967

By Bedrand L. Johnson

THE phosphate-rock industry is built upon natural deposits of rocks and minerals in which the element phosphorus is present as a phoshate. The term ?phosphate rock? is a general one, applied to certain rocks of different degrees of consolidation and of diverese origin, charater and occurrence, composed of intimate mixtures of several phosphate minerals, largely submicrocrystalline, usually calcium phosphates, in commerical quantities, with various impurities. This term includes phosphatized limestones, sandstone, shales, and igneous rocks; nodular phosphates ; residual weathered phosphatic limestones ; vein phosphates ; and phosphatic sediments, both consolidated and unconsolidated.

Jan 1, 1944

By R. G. Vardiman, M. R. Achter

Observations of dislocation structure in niobium are presented using two techniques. Triangular pits developed by electroetching are confined to orientations in the stereographic triangle between the (111) pole and planes of the (1ll) zone and require the presence of carbon. Some unusual electroetching phenomena at other orientations are noted. A chemical etch of dislocations decorated by the addition of carbon to 50 ppm reveals the complete dislocation line structure in a surface layer up to 30 p deep, with a resolution of less than 1 p. This effect is independent of surface orientation. The structure of subboundary nets may be resolved for misorientations up to about 1'. Dislocation structures found in strain anneal grown crystals, such as helices, prismatic loops, and high-density areas, are observed. The measurement of dislocation density is discussed and values obtained in different ways are compared. IN the course of some work on the response of refractory metals to thermal-mechanical treatments, it was desired to examine the defect structure of relatively low dislocation density crystals of niobium in bulk form. Surface and bulk methods for the observation of dislocations have been reviewed by ~melinckx,' and include etch pitting, decoration, and various X-ray techniques. The dislocation line structure has been developed by decoration in a few metals, although observations were limited to certain orientations, or by the coarseness and nonselectivity of the precipitate. The most commonly used technique is etch pitting. In niobium, etch pits have been developed chemically'0," in material of high impurity content and electrolyti-cally'' in relatively pure material. In this paper, etch pits developed electrolytically, and the dislocation line structure of a surface layer developed by decoration and chemical etching, are examined, and observations are presented from both techniques. EXPERIMENTAL METHODS Our starting material was electron-beam-melted niobium, swaged to 4 or -in.-diam rod. Chemical analysis is given in Table I. Single crystals were grown by a strain anneal technique using 1 to 2.5 pct of strain and growth temperatures of 1700" to 2300"~.'~ Some crystals grown by zone melting were also examined. The desired surface orientation was exposed either by spark machining or by sectioning with a cut-off wheel and prepared for etching by electro-polishing.

Jan 1, 1969

By M. R. Tek, K. H. Coats, D. L. Katz

The performance of a gas reservoir su,bject to water drive is often affected by interference due to gas procluction or injection in neighboring reservoirs adjacent to a common aquifer. Field data available on production-pressure behavior of several reservoirs indicate that prediction of reservoir performence must include the effects due to mutual interference. A method developed to predict the performance of two or more interfering gas reservoirs, subject to specified production-iniection .rchedule.s, is presented. The method involves the comhinatiorz of the theory of unsteady-state water movernent with appropriate meterial balance consideration.s. The procedure which extends M. Mortada's treatment for interfering oil reservoirs makes use of his dimen-.sionless pressure drop quantities. prevented graphically in the literature. In order to evaluale the predictive accuracy and practical field applicability of the theory, the method has been applied to analyze the performance of two actual gas reservoirs in mutual interference. The calculations were performed on an IBA4 704 computer. The predicted performances were alro calcltlated with the interference effects ignored. The results show that considerably better agreement between calculated and observed behavior ic. obtained when the interference effects are included. INTRODUCTION Fluid communication between any number of oil or gas reservoirs adjacent to a common aquifer results in mutual interference effects on their production-pressure behavior. The theory, application and interpretation of pressure build-up behavior of oil wells, drawdown tests on oil or gas-producing formations and behavior of several storage reservoirs indicate ample experimental evidence of mutual interference. A method developed to compute the behavior of interfering oil reservoirs was published several years ago by Mortada.4 Studies conducted during the recent years on underground storage of natural gas clearly indicated the need for extending Mortada's work to the case of interfering gas reservoirs. The adoption of appropriate material balance equations in conjunction with the unsteady-state pressure interference theory yields pressure-explicit equations. Their solution, their application to a specific case history and an over-all evaluation of the developed method through the comparison of predicted and observed field performances were the main objectives of this study. DEVELOPMENT OF MATHEMATICAL RELATIONS The diffusivity Eq. 1 governs planar, radial, unsteady-state compressible liquid flow through a porous medium. ?p/?r2+1/r ?p/?r=µFc/k ?p/?t (1) The 1iterature1,2,3 contains derivations and solutions of

By Paul F. Kerr

The uranium-producing areas near Marysvale, Utah provide an unusual group of veins and replacement deposits associated with a Pliocene-Oligocene intrusive and extrusive igneous complex. Aside from several scattered occurrences in older volcanics, uranium-bearing veins occur in intrusive quartz monzonite or granite and in nearby rhyolite. The veins in general trend within a few degrees of N55-65°E, are more or less vertical, and are found along the western margins of a quartz monzonite intrusive. The replacement deposits are found in rhyolite intrusives and also in the lower portions of rhyolite flows close to places where veins forming solutions rising through quartz monzonite came into contact with the rhyolite. At least 14 veins have been mined since uranium mining operations began at Marysvale some 16 years ago, while ore has been extracted through about 10 miles of underground workings. The active mmmg area is approximately 3000 feet long and in the central portion 1500 feet wide. Ores have been found over a vertical spread of almost 2000 feet, between the highest occurrence on Jungfrau Hill ( ca. 7200 feet) and the deepest discovery of ore in a drill hole near the Prospector Mine (ca. 5200 feet). Under existing mining and marketing conditions, mining along the veins in the main area appears to have reached an economic limit at about 500-600 feet below the surface. However, orebodies in the rhyolite and in the upper portions of veins close to the rhyolite are subject to active mining. Isotopic dates indicate that the uraninitebearing veins and replacements are late Miocene or Pliocene (ca. 10-13 m.y.), the rhyolite is Miocene (avg. 17.5 m.y.), and the quartz monzonite and granite intrusives are late Oligocene (23.6 to 26.0 m.y.). The older Bullion Canyon Volcanic Series which encircles the area is Oligocene (28 to 31.1 m.y.). Two generations of alteration occur: ( 1) Earlier alunitic veins and replacement bodies are found in the Bullion Canyon Volcanic Series, none of which have produced uranium; (2) Later argillic alteration associated with the introduction of uranium is found along veins, replacing glassy rhyolite dikes and replacing phases of the rhyolite.

Jan 1, 1968

By G. F. Loughlin, C. H. Behre

THE DEVELOPMENT OF CLASSIFICATION WHAT is the use of a classification of mineral deposits? From the days of Agricola, the founder of the science of ore deposits, successive authors on the subject have attempted classifications, none of which have attained unanimous indorsement of miners, engineers, or geologists. The miner and engineer naturally have little regard for a classification that does not help them to find ore. Mining geologists may share this feeling, and deplore the overemphasis that may be placed on classification by their academic brothers. Apparent effects of such overemphasis may be reflected by students or new graduates who have grown to think that each deposit must fit perfectly into some pigeonhole of the more or less arbitrary scheme that has been drilled into them. Diversity in mineral deposits as in other natural phenomena, however, is too great to be fully expressed in the usual tabular classification, and experience is essential for the appreciation of the value or usefulness of a classification. The succession of classifications has closely followed the growth of the science of mineral deposits and reflects that growth, as well perhaps as the limited or comprehensive viewpoint of each proponent. The earliest classifications were based on metal content, and were superseded by those based mainly on form of deposit. Source of materials also became a basis, and was followed by physical and chemical conditions and processes. In spite of this development it is interesting to note that in many of the latest reports on mining regions the authors adopt special classifications suited for their particular districts. Some of these, like the earliest classifications, are based primarily on metal content, and others are most conveniently based on form, and it may be convenient to modify these by reference to source of material or temperature of deposition. Some, including the writers, after noting these different usages, have refused to worry much over classification as an ultimate objective, but,

Jan 1, 1933

By J. M. GLEDHILL

IT would doubtless have been felt by many but a few years back that there was little left to be said on the subject of crucible tool-steel, and that something akin to finality had been arrived at in its manufacture and general treatment. Probably such feeling was justifiable when it is remembered that the making of steel in crucibles is by far the oldest method known, dating back from time immemorial, it being indeed impossible to accurately trace its origin and earliest development; but it seems certain that carbon-steel was made and used thousands of years ago for cutting-tools. Proof of this may be seen by the marvelous carvings and workings on the intensely hard stone-work of the ancients, for it would be difficult to conceive by what means, other than with steel tools, such work could have been executed; and it is wonderful to contemplate that steel cutting-tools should have been used so long ago, whilst the principle of manufacturing them-that is, by fusion of iron and charcoal in crucibles-was then in a measure on the sane lines as we work on at the present day. Archaeologists have discovered that the Chinese made steel in crucibles long before the Christian era. " Wootz " steel fabricated in India centuries ago was crucible steel, as was also the celebrated Damascus steel, produced at the forges of Toledo, and, curiously, this latter steel furnishes' yet another proof that "There is nothing new under the Sun," for it is recorded that Damascus steel contained certain percentages of tungsten, nickel, manganese, etc., some of the very elements, in fact, contained in the present modern high-speed steel, so that a latent high-speed steel may be said to have existed

Mar 1, 1905

By Albert J. Phillips

FOR the most part, recent changes in nonferrous physical metallurgy have been gradual and of a transition nature rather than abrupt modifications of existing methods. Development of new alloys containing vital constituents in what formerly would have been considered minute amounts has necessitated more precise control of metallurgical procedure than ever before. Realization of the remarkable effects of minute amounts of specific foreign elements in many alloys has brought about a revolutionary control in the selection of even the most commonplace raw materials. In addition, recognition of the widespread occurrence of precipitation hardness in metal systems, and the utilization of many of these, has emphasized not only the need for precise temperature control but also the necessity for considering the time factor in its effect upon properties in the treatment of most metals. These needs have caused the development and widespread installation of equipment that permits precision of control undreamed of a generation ago.

Jan 1, 1935

By Thomas H. Sheldon

IN the zeal for opening up new ore-bodies, or for. extracting the ore from attractive bodies gal ready opened up, we very often lose sight of the fact, that, after all, the operation of a mine is a business proposition, pure and simple; and for the best working-results should be treated upon a strict business basis. Of course, in every mine of consequence a record is kept of expenditures and receipts, and such glittering generalities as "gross receipts," " net receipts," " mining expenses," .and " per cent. profit," can be told to the cent; but does this . record show economy of management, either as compared with the same record of other months, or as compared to the record of other mines of the' same class ? Moreover, if such a record shows that the cost of mining is high, does it in any way en¬able the manager to put his finger on the leakage? Does it necessarily follow that a mine which makes a profit of, say, 40 per cent on 25-dollar ore, is doing less economical mining than one which saves 60 per cent on 80-dollar ore ? Of course the figures in the latter case look the more attractive, but when it comes to a point of saving everything which can be saved, and of cutting down expenses to the lowest possible cost of operation, the former mine is doubtless on the most firm and economical financial basis. But as the relative merits of the system of mining in the two cases, nothing could be decided without a basis of detailed comparison ; if one system is more economical than the other, why is it so, and wherein does the advantage lie ? This can be shown only by keeping accurately the cost of each mining operation. And no matter how dissimilar two mines may be in character and operation, yet there are a few general heads common to all mining operations. In the first place, it is necessary to break the ore from the solid ground ;

Nov 1, 1905

Institute of Metals Division Ferrous and Nonferrous Physical Metallurgy Established as a Division April 26, 1918 (Bylaws published In the 1944 TRANSACTIONS Volume of the Division) A A SMITH, JR, Chairman E A ANDERSON, Past-Chairman F N RHINES, Senior Vice-Chairman W A DEAN, Vice-Chairman H A MALONEY, Treasurer ERNEST KIRKENDALL, Secretary 29 West 39th Street, New York 18, N Y Executive Committee R M BRICK 2 W A JOHNSON 1 H I DIXON 2 E W PALMER 1 M GENSAMER 2 J H SCAFF 3 J D HANAWALT 1 J D SULLIVAN 3

Jan 1, 1952

By W. H. Yarroll Discussion by W. A. Griffith

W. A. Griffith (Head, Research Department, Phelps Dodge Corp., Morenci, Ariz.) - It is gratifying to see the increasingly common use of classical statistical procedures by metallurgical researchers. Mr. Yarroll has given excellent illustrations of the utility of multiple correlation analysis of complex metallurgical data. Our experience in applying these procedures to historical plant operating data has differed, however, from that which he suggests. The uninitiated frequently assume that the volumi-

Jan 1, 1969

By B. E. Warren

Jan 1, 1965

By Fulton Flick

THE micrography and macrography of aluminum and its alloys present certain difficulties. Many of the difficulties attendant on the micrography have been removed by methods developed during the past few years, notably those of E. H. Dix, Jr.1 The development of grain size in aluminum and its alloys may be equally troublesome, yet comparatively little detailed attention appears to have been given to it. Satisfactory reagents. are available for the development of such structures in ferrous and most non-ferrous metals, but those applied to aluminum and its alloys, i. e., alcoholic or aqueous solutions of sodium hydroxide or hydrofluoric acid are not entirely satisfactory. Hanson and Archbutt,2 in speaking of these two reagents, state that "These two reagents give fairly satisfactory results, but they sometimes produce badly tarnished surfaces from which the surface deposit is difficult to remove." It has been our experience that neither of these reagents is to be entirely relied on for developing structures suitable for study or photography. This means that when the etch fails to produce satisfactory results the, specimen must be repolished, through the 000-paper at least, and then etched with another reagent. This procedure entails a con¬siderable loss of time, and the final results may not be all that might be desired. However, the reagent to be described, although not a panacea for all etching troubles, has improved results so markedly that it is felt that it is worth offering as a grain-size etch generally applicable to aluminum and aluminum alloys. Czochralski3 in 1915 mentioned the application of a solution of 10 to 20 c. c. concentrated hydrofluoric acid in 100 c.c. absolute alcohol, etching in this reagent being followed by dipping in concentrated hydrochloric-acid solution.

Jan 2, 1925

By Eugene R. Rice

There are many methods for determining the meridian, but all of those in common use involve at least two separate observations, one for latitude and one for azimuth. Such observations made upon a south star at any hour are open to the objection of possible inaccuracy due to ignorance of the absolute refraction, and also to slow change in the altitude of the star when near the meridian. The method of observing a circum-polar star at elongation. besides requiring a separate observation for latitude, is open to the serious objection that clouds may obscure the star at the critical moment. Moreover, a tedious wait for the star to come to elongation is sometimes necessary. Many of us can recall 'long, cold, weary vigils, waiting for Polaris to reach elongation. For observing a circumpolar star at any hour, not only the latitude, but also the true time, must be known. This it is practically impossible to obtain, except in regions reached by the telegraph, and usually then one has to know the longitude also, in order to reduce " standard time" to " local time." The results obtained by this method, when the star is at culmination, are not very good, unless the true local time is absolutely known. The methods of obtaining the nleridian from the sun, by means of a solar attachment, or by direct observation, while good, are not absolute, by reason of refraction, change in declination of the sun, and small change in vertical angle, when the sun is near the meridian. For these two methods, latitude, time, and approximate longitude have to be known. In the method here described, only one observation is needed, and from it are computed azimuth, latitude, aud sidereal time. In other words, one call observe a circumpolar star—Polaris

Jan 1, 1911

By Francis T. Freeland

In the West many precious-metal mines are worked in patches by lessees, under conditions which closely resemble those of what is called " tribute-work" in Cornwall.* The company has its own foreman or inspector, and usually employs the engineman, blacksmith, pumpman, and perhaps other general workmen. As an inducement to work on a new piece of ground, where no ore is in sight, the company may advance a " footage"

Jan 1, 1896