Search Documents

By F. Weinberg

Lead single crystals have been deformed in tension over the temperature range of 4.2°K to the melting point. Changes in flow stress resulting from temperature cycling and strain rate cycling have been measured as a function of temperature for crystals of different orientations and purity. It was found that the flow stress ratio, after correcting for the temperature dependence of the shear modulus, decreased progressively with temperature above approximately 0.5Tm. The activation energy calculated from the high-temperature portion of the curve was found to be markedly higher than that of self-diffusion. For single glide crystals, the corrected flow stress showed an increase above 0.5 Tm before decreasitzg with temperature. This increase is attributed to static recovery occurrittg during temperature cycling. THE temperature dependence of the flow stress, based on temperature cycling and strain rate cycling, has been extensively investigated,' and on the basis of these results dislocation models of the work-hardening process have been proposed. In general, the flow stress is divided into two parts, ts, the short-range interaction term, which is only effective at low temperatures and which decreases with increasing temperature, and TG, the long-range stress term, which is independent of temperature after allowing for the temperature dependence of the shear modulus. The observations demonstrating that tG/µ is independent of temperature were generally carried out at low temperatures to minimize recovery effects. Several investigations have been reported on flow stress measurements at high temperatures2"5 which demonstrate that TG/µ does not remain constant at temperatures above 0.5Tm (where Tm is the melting temperature of the material in OK). Specifically, Hirsch and warrington3 carried out temperature cycling tests at two strain rates on single and polycrystalline aluminum up to 0.8 Tm and on polycrystalline copper. For aluminum they found that the flow stress ratio (the flow stress at temperature T2, divided by the flow stress at the reference temperature T1 in one temperature cycle) dropped progressively with increasing temperature above 0.5Tm. From the slopes of the high-temperature portions of the curves, they determined an activation energy for the deformation process of 1.6 ev (at best) which they considered was in agreement with the activation energy of self-diffusion, 1.35 ev. Calculations of the activation volume demonstrated that the deformation was not controlled by dislocation climb. They proposed a mechanism in which the rate-controlling process at high temperatures was due to the rate of move- ment of vacancies away from jogs, i.e., that of self-diffusion. Results of Lucke and Buhler4 on single crystals of aluminum confirmed this conclusion. They measured the critical resolved shear stress of aluminum over a wide range of temperature and strain rates. They found that the temperature dependence of the critical resolved shear stress was similar to that of the flow stress ratio, as determined by Hirsch and Warrington, and from their data calculated an activation energy for high-temperature deformation of 1.35 ev identical to that of self-diffusion. More recently Gallagher5 has carried out a detailed investigation of the temperature dependence of the flow stress ratio of copper, silver, and gold. In all cases, he found that the flow stress ratio, after adjusting for the shear modulus temperature change, drops at high temperatures. The activation energies he determined were found to be appreciably higher than the activation energy of self-diffusion of the material being considered. The flow stress ratio was found to be dependent on the orientation of the material, and, in addition, an anomalous increase in the flow stress ratio for copper, oriented for single glide, was observed above 0.5Tm. The purpose of the present investigation was to measure the critical resolved shear stress, the flow stress ratio, and the strain rate sensitivity of lead, primarily as a function of temperature. The results should indicate whether, following Lucke and Buhler, the critical resolved shear stress of lead has the same temperature dependence as the flow stress, and, following Hirsch and Warrington, whether the activation energy for high-temperature deformation in lead is the same as that of self-diffusion. Lead deforms as a normal fee material,6'7 is available in high-purity form, can readily be grown as single crystals, and, for this investigation, has the very considerable advantage of having a low melting point, 327°C. The observations of the critical resolved shear stress of lead have been published elsewhere.' EXPERIMENTAL PROCEDURE The experimental procedure was essentially the same as that used in the critical resolved shear stress measurements.' Single crystals of 99.999 pct (59) and 99.9999 pct (69) lead were deformed in tension with a table-model Instron in a silicone oil bath above room temperatures and in a cooled methyl alcohol or liquid-nitrogen bath below room temperatures. The test specimens were rectangular in section, 0.65 by 0.33 cm, and had a 5-cm gage length. The specimens were grown as single crystals with tapered ends, which fitted into matched tapered grips for testing. To obtain the flow stress between two temperatures, specimens were first deformed approximately 1.0 pct at the higher temperature. The test was then stopped, the load relaxed, the oil bath removed without disturbing the specimen, the grips and specimen cooled with a fan and then immersed in liquid nitro-

Jan 1, 1969

The age of specialization has made man increasingly dependent on a larger number of different metals and minerals. Overexploitation during World War II and lavish squandering of irreplaceable mineral wealth in the past has resulted in the rapidly approaching exhaustion of some of the major domestic ore sources. History clearly points out that the United States cannot continue to be a world power on an "import to survive" policy. A constructive program of development and appraisal of the nation's mineral wealth, including the planned conservation of her resources, must be adopted. Strictly speaking, conservation of minerals must mean the orderly exploitation of our resources and the prevention of waste in use, with due regard for the future. Real concern for the future may not extend beyond a few generations. Eventually science and invention should take care of the problems arising from shortages of some minerals, and the national defense aspects of domestic deficiencies can be provided for by stock piling and other measures. Early conservationists had this viewpoint; but with a rapidly developing industry and population, a farsighted policy that would deny full realization of immediate ambitions became unpopular. Consequently, the politically minded conservationist broadened the concept to include "prudent use of resources" and brought under the conservation umbrella

Jan 1, 1950

FRank FirmstoNe, Easton, Pa.: The effect of lead on brass seems to have been recognized by Berthier, and the facts published by him as early as 1818 (Ann. des Mines, 1st ser., iii., 1818, p. 347 et seq.). He there says expressly that copper containing lead makes " dry " (see) brass, and that, for the same reason, blast-furnace

Jan 1, 1898

By H. LeChatelier, B. Bogitch

Page Introduction........................... 134 Methods of Investigation....................... 135 The Tridymite Network...................... 137 Independent Variables....................... 146 Manufacturing Operations..................... 153 Introduction Silica brick are indispensable in the manufacture of steel because they alone are able to withstand the high temperature of regenerative furnaces. All attempts to replace silica brick by other refractory materials for this purpose have failed, but the reason for this failure has remained obscure; we shall give an explanation later in this paper. Before the war, silica brick employed in France came principally from abroad, for which reason, since the beginning of hostilities, certain French steel works have been seriously handicapped. Our attention was first directed to the question by M. Bied, Engineer of the Teil Works. With him, we began certain investigations, at first using our laboratory and the furnaces of neighboring steel works. The larger part of our experiments, however, have been made in the laboratory of the Faculty of Sciences at the Sorbonne. For the heating of our samples, we are deeply obliged to MM. Charpy, Yeatmann and Guerineau. In undertaking these studies, our first aim has been to render assistance to French industry, by indicating, as precisely as possible, the necessary conditions for the manufacture of high-grade brick; but at the same time me have

Jan 1, 1919

By S. L. Lopata, E. B. Kula

A variation of yield and tensile strength with direction has been noted in heat-treated 4340 steel which had been warn-worked by rolling in the austenitic condition prior to quenching. Measurements by X-rays showed a preferred orientation of martensite crystals. Various ideal preferred orientations of martensite were calculated by assuming a preferred orientation for austenite and transforming this to martensite by the Kurdjumov -Sachs and Nishiyama relationships. Comparison with the measured preferred orientation showed that the ideal rolling texture for austenite in 4340 steel could be expressed as a (112) [111] texture with a component of (110) [112]. No evidence was found for any fiber axis in the rolling direction, or fop- a (123) [412] texture. The observed martensite pole figures can be adequately accounted for by these ideal austenite textures and by the Kurdjumou-Sachs or Nishiyama transformation relationships between austenite and martensite. ALTHOUGH preferred orientations are found in cold-rolled steel sheet and in many nonferrous metals, they are not generally encountered in wrought, heat-treated high-strength steels, since such steels are generally not cold worked sufficiently to develop a strong texture, and any texture that is present is removed during heat treatment by the phase transformations taking place. This report gives details on a preferred orientation found in warm-rolled and hardened 4340 steel. In a recent study, a special combination heat-treating and working technique was used in which 4340 steel was deformed in the austenitic condition, and before re crystallization of the austenite could occur, quenched to form martensite.' Since the austenite was unrecrystallized, it was cold worked and hence could have contained a preferred orientation which could be transmitted to the martensite on quenching, and this in turn could be manifested as a directionality of mechanical properties. Such a directionality of properties was found as a result of working, and this prompted an X-ray study of the preferred orientation. Literature Survey— Rolling Texture in Face-Cen-tered-Cubic Austenite—M a preferred orientation is found in a rolled and hardened steel, it is first appropriate to consider what texture existed in the austenite as a result of the rolling but prior to the transformation to martensite. The changes taking place as a result of the austenite-martensite transformation are then considered. In view of the instability of austenite in 4340 steel at low temperatures, no direct determination of the austenite texture was made. However, an estimate of the texture for austenite in 4340 steel may be made by considering the textures found for other face-centered-cubic metals. Barrett' has reviewed the rolling textures for many materials. The most common orientation in face-centered-cubic metals has the (110) planes parallel to the rolling plane and the [112] directions parallel to the rolling direction, or (110) [112]. Other orientations found are (112) [111], as well as (100) [001], (110) [001], and others. Beck and his co-workers, using quantitative pole figures, report that (123) [121],3 later corrected to (123) [412],4 better describes the ideal orientation. smallman5 reported that the ideal preferred orientation for high-purity face-centered-cubic metals is (123) [121], but that there is a transition to (110) [112] as solid solution elements are added. The latter texture tends to occur more readily at lower temperatures. This transition between the two textures was explained by differences in the slip characteristics with concentration or temperature. More recently, Jones and Fell6 concluded that the (123) [412] texture for face-centered-cubic metals could equally well be represented by a mixture of (110) [112] and (112) [111] textures, and hence it had no physical reality. From the above results it can be seen that there is no agreement on the "ideal" texture for fcc metals and, hence, no firm basis for assuming a texture for austenite in 4340 steel. Therefore, the orientations (110) [112], (123) [412], and (112) [111] have been considered in the following.* *The (123) [4121 is identical to the (123) [121] rotated 90 deg. Orientation Relationship between Austenite and Martensite—When martensite forms from austenite, certain crystallographic planes of the martensite are parallel to planes in the austenite. This orientation relationship was first determined by Kurdjumov and

Jan 1, 1960

By R. K. Buhr, H. Thresh, M. Bergeron, F. Weinberg

The microsegregation of nickel and chromium in directionally solidified AISI 4340 steel castings has been measured using electron probe microanalysis. Minimum concentrations were observed to occur at the center of the dendrite stalks, as reported previously. However, the position of the maximum concentrations could not be determined from the dendrite configuration. An etching technique has been developed which shows the position of maximum concentration. Measurements were made of the distribution of nickel and chromium in the dendritic structure. The ratio of maximum to minimum concentration was determined as a function of primary dendrite arm spacing for both as-cast and partially homogenized materials. The results are compared with observations reported in the literatuve. A S part of an investigation of solute segregation in directionally solidified AISI 4340 steel casting, electron probe microanalysis was used to measure the distribution of nickel and chromium in the dendritically segregated material. This complemented the observations on the segregation of radioactive phosphorus obtained by autoradiographic techniques in the same castings.' Kattamis and I?lemings2 have reported similar measurements, using electron probe microanalysis, on dendritically segregated AISI 4340 steels. They found minimum solute concentrations occurred at the center of dendrites, maximum concentrations occurred in the center of interdendritic regions, for symmetrically oriented dendrites, and a regular variation of concentration within dendrite arms. The ratio of maximum to minimum concentration was found to be essentially independent of position in the castings, except near the chill surface where it was somewhat higher. Assuming complete diffusion in the liquid and no diffusion in the solid during freezing, they considered that isoconcentration curves in the steel were homothetic. As a result, isoconcentration curves of the various elements, contour surfaces of dendrites produced by isothermal-transformation studies, and the contour of the solid-liquid interface would all be similar, and could be superimposed by a uniform expansion or contraction of the contours. Preliminary results of the present investigation suggested that isoconcentration curves were not homothetic. It was also evident that points of maximum concentration could not be predicted from the dendrite configuration. Since the ratio of maximum to minimum concentration appeared to be an important parameter in defining the overall segregation in a casting, other techniques for determining the point of maximum concentration were investigated. In addition the overall solute distribution associated with the dendritic structure was examined for both nickel and chromium, and the consistency of the distribution for neighboring dendrites was determined. METHOD Fifty-pound heats of AISI 4340 steel were cast in a manner similar to that used by Flemings et al3 with a water-cooled copper base plate and exothermic sides and top. The nominal composition of the material was C, 0.41 pct; Mn, 0.66; Si, 0.35; S, 0.012; P, 0.010; Ni, 1.88; Cr, 0.95; Mo, 0.28. The steel solidified directionally from the chill surface, with a dendritic structure which increased in dendrite arm spacing with increased distance from the chill. Results of the general investigation of the cast structure and segregation of radioactive phosphorus in these castings have been reported elsewhere.' For the present measurements, sections were cut from the casting at several distances from the chill surface. The sections were subsequently heat-treated, mounted, and then polished on a plane perpendicular to the general freezing direction of the casting. Electron probe microanalysis was carried out with the JEOL-JXA3 microprobe using a voltage of 25 kev and beam current of 0.15 µa. The take-off angle is 22 deg. Quartz crystals were used in the spectrometers and measurements made for Ka radiation from both nickel and chromium simultaneously. A thin layer of carbon was deposited on all specimen surfaces prior to examination in the microprobe. Early measurements were made on polished surfaces, with indentation marks produced by a hardness tester to indicate the area of interest. It was found desirable to use etched surfaces, as opposed to polished surfaces, to reduce sample preparation time and more readily relate the microprobe scan to the structure. To determine if this could be done, without introducing significant errors, a series of measurements were made on polished and etched surfaces of the same specimen. Both polished and etched surfaces produced similar results within normal scatter as shown in the observations. Subsequent measurements were then made on etched surfaces. Measurements with the microprobe analyzer were made by point counting, for periods of 100 sec, at 10-µ intervals. Ten-second counts were made on pure nickel and chromium standards, incorporated in the specimen mount before and after each set of measurements. The results were adjusted for background, then corrected for dead time using the expression:

Jan 1, 1969

By K. Huessener

In presenting the following data on combustion in the open hearth furnace and the advisability of automatic combusion control, the author finds himself much more severely handicapped by the lack of reliable test results than he had anticipated when he first undertook to write this paper. In order thoroughly to investigate how the results of an open-hearth furnace are influenced by combustion, one would have to draw up a large number of heat-balance sheets, as Kinney and McDermottl have given for one heat in their extremely able paper on "Open Hearth Efficiency,' presented before the American Iron and Steel Institute on October 27th,1 1922. Instead of covering only one heat, however, such heat-balance sheets would have to embrace a large number of heats, and not only for one kind of fuel, but for all the various fuels in customary use. Use of Radiation-protected Pyrometer Such tests necessitate extremely careful temperature readings, and here the first serious difficulty presents itself. Nearly all the temperature readings so far published have been taken with thermocouples for the lower ranges and with optical or radiation pyrometers for the higher ranges. This method of measuring reveals the temperature of the surrounding walls, or in the case of optical or radiation measurements, the temperature of that part of the opposing walls which has been focused by the instrument. The error in ascertaining the temperature of the gases entering or the waste gases leaving the checker chambers is probably not very large, as the flowing gases impart their temperature to the walls of the flues. On the other hand, the uptakes, where the preheat temperature of gas and air are usually measured, are under the influence of radiated heat from the port ends, and correct temperature readings can here be taken only by using a radiation-protected pyrometer of the aspirating type.

Jan 1, 1926

By Strathmore R. B. Cooke, Iwao Iwasaki, C. S. Chang

The effects of aeration on an aqueous suspension of pyrrhotite were studied and their results correlated with flotation tests using xanthates as collectors. The effects of copper activation and of pH variation were determined and possible mechanisms postulated. PYRRHOTITE has long been considered a gangue mineral to be eliminated as tailing in the treatment of various sulphide ores. However, in recent years the world-wide lack of sulphur resources has called attention to this mineral as a potential source of both sulphur and iron. Its importance as an economic mineral, however, has not been particularly emphasized. For this reason very little is known about its response to flotation, except that it can be depressed easily in alkaline circuit, by long aeration,1,2 addition of oxidizing agents,3 or by starch.' The object of this work was to study the floatabil-ity of pyrrhotite. This includes the effect of oxidation by aeration, of copper activation, and of change in pH. Preparation of the Pyrrhotite Sample: It was desirable that the highest grade of pyrrhotite obtainable be used for this experiment, since the presence of other minerals could affect the surface properties.5 However, no pyrrhotite was available as crystals, and massive deposits of hydrothermal origin commonly contain considerable amounts of chalcopyrite. Pyrrhotite concentrate was, therefore, prepared from a sulphide deposit occurring near Aitkin, Minn. The deposit is of pyrometamorphic nature consistirlg mainly of pyrrhotite and pyrite with graphite, silicates, and carbonates as gangue. The ore, already crushed through 3 mesh when received, was screened at 65 mesh and the undersize discarded. The oversize was crushed through rolls, and then stage-ground dry in an Abbe porcelain mill, the —65 mesh portion being screened out after every 15 min of grinding until all the material passed through this size. The ground product was then concentrated with a drum-type dry magnetic separator. The rougher concentrate was cleaned twice and then demagnetized. The final product was split in a Jones splitter and stored in air-tight bottles. Microscopic examination of the concentrate showed that it was relatively clean and free of pyrite, locked particles, and gangue. By means of the krypton gas adsorption method," the specific surface was determined to be 3000 cm2 per g. The chemical and screen analyses of the final concentrate are given in Tables I and II respectively. It is a well-recognized fact that the oxidation of some sulphide ores during stockpiling, grinding, and conditioning affects their flotation behavior. The problem of oxidation may become serious in the case of pyrrhotite, since this is known to be more easily oxidized than many other sulphides. To ascertain the extent of oxidation, an experiment was carried out by aerating an aqueous suspension of pyrrhotite with air, oxygen, and nitrogen as follows. A 300-g sample of pyrrhotite in 2700 ml of water was agitated and simultaneously aerated in a Fager-gren-type laboratory flotation machine. A Precision wet test meter was connected to the air inlet valve, the flow rate of the gas being kept constant at 0.3 cu ft per min throughout the experiment. Samples of approximately 30 ml each were taken from the cell at 0, 4, 10, 20, 35, 60, and 90 min. After the pH was taken, each sample was filtered and the filtrate was analyzed for total iron and sulphur. The iron was determined colorimetrically by the thioglycolate method using a green filter.' The filtrate was oxidized with bromine to convert all of the soluble sulphur compounds into sulphate and this was determined with a Parr turbidimeter." When aeration tests were made in alkaline circuit, calcium hydroxide or sodium hydroxide was added at regular intervals to maintain a constant pH. A similar procedure was followed in an experiment to determine the abstraction of copper. ion by pyrrhotite. In this case various quantities of cupric chloride were added. The filtrate from each sample taken was analyzed for copper, total iron, and sulphur. The carbamate method with a green filter was used for the copper analysis,' since this method could tolerate a considerable amount of iron in the solution. A pneumatic cell, made from a 350-ml fritted glass Buechner funnel, was used for this experiment. The detail of the assemblage has been described elsewhere." In the present work a stainless steel baffle was inserted in the cell. This baffle overcame the tendency for the coarse pyrrhotite particles to be swirled around the wall of the cell and thus fail to collect in the froth. A 50-g sample of pyrrhotite was added to the cell which contained 260 ml of water. When pretreat-ment of the sample was desired, reagents, such as activator and pH regulator, were then added and the pulp was conditioned for a specified conditioning time. Prior to the addition of the collector approximately 15 ml of the solution were removed for pH measurement and for iron and sulphur analyses. Copper when used as activator was also determined. Collector and frother were then added and the pulp was conditioned for an additional 2 min. Air was admitted to the cell and the froth removed. The separation required from 4 to 6 min, depending on the characteristics of the froth. The float and non-float products were filtered, dried, weighed, and assayed for iron.

Jan 1, 1955

By A. Satter

Studies of wellbore heat transtnission during the injection of a hot fluid, as either gas or liquid, have appeared in he literature. The present investigation takes into account the effect of condensation, which is of practical sig-nificance when considering steam injection operations. Calculation procedures are given for superheated and for saturated and undersaturated steam. Effects of injection rate, time, pressure, temperature and depth of a well on heat losses have been analyzed. The benefits of using a packer are discussed. Also presented are correlations for estimating heat losses involved during injection of saturated steam. INTRODUCTION Studies of wellbore heat losses during the injection of a hot fluid have appeared in the literature. Ramey' has presented a useful solution for calculating temperature of a heated gas as a function of depth and injection time. Ramey and others have also presented solutions for the hot liquid case.'. ' No method is available to take into account the effect of condensation, which is of practical significance when considering steam injection operations. This paper presents a method of estimating the quality of a condensing fluid as a function of depth and time. The approach is basically the same as that used by Ramey. The following injected fluids and conditions are considered in this study: 1. Injection of superheated steam A. Decrease in temperature until cooled to the saturated state B. Condensation until condensed completely into hot (saturated) water 2. Injection of saturated or undersaturated steam; condensation until condensed completely into hot (saturated) water. Although this investigation does not include cooling of water after steam is completely condensed, Ramey's solution for the hot liquid case can be used for this purpose. The effects of various process variables on heat losses During the injection of steam into a well are investigated. THEORY QUALITY OF CONDENSING STEAM Predicting the behavior of condensing steam flowing down the injection wellbore requires an estimate of the quality of steam, i.e., the mass fraction of vapor in the mixture. Let us divide the total depth of the injection well into several segments which might be, but do not have to be, of equal magnitude. Consider condensation within a given depth interval AZ, the bottom of which is located at a depth Z from the surface (Fig 1). The following equation, derived in the Appendix- relates the quality of steam at the bottom of an interval to that at the top of the interval:

Jan 1, 1966

By E. S. Rowland, J. Welchner, R. H Marshall

This paper presents results on an extension into the realm of high-carbon steels of some work recently published1 on the effects of time at temperature, quenching temperature and prior structure on the hardenability of one 0.20 and four 0.40 per cent carbon alloy steels. It was shown at that time that unless the conditions of time, temperature and prior structure are substantially the same in performing the hardenability test as in conducting hardening of parts in production, the correlation of hardenability information with the hardness and properties of production parts is often not of satisfactory accuracy. The general effects of these variables on the austenitic grain size, distribution of excess carbides and critical cooling rate have been known for many years and one or more have been investigated by Shepherd,2,3 Davenport and Bain,4 Digges,5,6 Digges and Jordan,' Post and associates8 and Roberts and Mehl,9 to mention only a few. There has been no systematic investigation, however, into the quantitative variations produced on the hardenability of commercial high-carbon steels by changes in these factors of time, temperature and prior structure. Procedure A plain carbon hypereutectoid steel, S.A.E. 52100 and Graph-Mo, a molybdenum-bearing high-carbon steel containing some graphite, were chosen for this investigation. The chemical analyses of these electric-furnace steels are given in Table I. The procedure used was exactly that reported previously,' hence the details will not be repeated here. Normalized (165o°F.) and spheroidized prior structures were utilized on all steels with hot-rolled and quenched (I600°F. oil) prior conditions added for the plain carbon steel. The end-quench test developed by Jominy10 was sclected for use in this investigation and, with the noted exceptions, the American Society for Testing Materials standard procedure was followed. The effect of time at temperature was examined at intervals of o, 10 and 40 min. and 4 hr., and a few 16-hr. tests were run. Salt-bath heating of the specimens was employed to control and minimize the

Jan 1, 1944

By J. D. Meakin, H. G. F. Wilsdorf

Using a combined decoration and etching technique the dislocation structure of annealed and deformed a brass has been studied. Annealed crystals revealed a low density forest and well-developed subboundaries; lightly deformed crystals contained discrete groups of dislocations. The dislocation density and the number of dislocations in a group were obtained from the micrographs. Using slip-line data, the mean path of a dislocation and the configuration of groups along an active slip plane have been deduced. Observations on secondary and cross-slip are reported. It has been the aim of many investigations to obtain detailed knowledge of the dislocation patterns which are present in metals before and after their deformation. The "decoration" of dislocations with impurity atoms has been considered as one of the promising experimental approaches, and much work has been done to develop this technique for revealing dislocation sites in metals. Following the early work by Castaing,' Castaing and Guinier,' and Lacombe and Berghezan~ on aluminum-rich aluminum-copper alloys, dislocations in this material have been studied extensively by others.+' In these alloys the dislocation sites act as nuclei for the precipitation of the second phase. The main results of the investigations on aluminum with copper are: i) the confirmation of the earlier contention that subboundaries consist of dislocation walls, ii) that many more dislocations are found in slip bands than in regions where less glide had taken place, iii) the observation of individual dislocations, lying nearly parallel to the surface investigated, and iv) that parts of dislocation loops, apparently emitted from a dislocation source, could be made visible. Recently, Jacquet, Weill, and Calvert have succeeded in revealing nearly concentric dislocation loops in quenched A1-4 pct Cu and thus indicated directly the existence of dislocation sources in a fcc metal specimen of normal dimensions. Another decoration method developed by Dash10'11 and applied to silicon crystals makes use of diffusing copper to the dislocations from a surface deposition. The dislocation pattern can then be observed by an infrared technique. His results include evidence for symmetrical and spiral Frank-Read sources, and for arrays of dislocation loops which follow simple crys-tallographic directions. Recently Low and Guard" have studied the dislocation structure of silicon-iron using carbon for the

Jan 1, 1961

By R. H. Marshall, J. Welchner, E. S. Rowland

This paper presents results on an extension into the realm of high-carbon steels of some work recently published1 on the effects of time at temperature, quenching temperature and prior structure on the hardenability of one 0.20 and four 0.40 per cent carbon alloy steels. It was shown at that time that unless the conditions of time, temperature and prior structure are substantially the same in performing the hardenability test as in conducting hardening of parts in production, the correlation of hardenability information with the hardness and properties of production parts is often not of satisfactory accuracy. The general effects of these variables on the austenitic grain size, distribution of excess carbides and critical cooling rate have been known for many years and one or more have been investigated by Shepherd,2,3 Davenport and Bain,4 Digges,5,6 Digges and Jordan,' Post and associates8 and Roberts and Mehl,9 to mention only a few. There has been no systematic investigation, however, into the quantitative variations produced on the hardenability of commercial high-carbon steels by changes in these factors of time, temperature and prior structure. Procedure A plain carbon hypereutectoid steel, S.A.E. 52100 and Graph-Mo, a molybdenum-bearing high-carbon steel containing some graphite, were chosen for this investigation. The chemical analyses of these electric-furnace steels are given in Table I. The procedure used was exactly that reported previously,' hence the details will not be repeated here. Normalized (165o°F.) and spheroidized prior structures were utilized on all steels with hot-rolled and quenched (I600°F. oil) prior conditions added for the plain carbon steel. The end-quench test developed by Jominy10 was sclected for use in this investigation and, with the noted exceptions, the American Society for Testing Materials standard procedure was followed. The effect of time at temperature was examined at intervals of o, 10 and 40 min. and 4 hr., and a few 16-hr. tests were run. Salt-bath heating of the specimens was employed to control and minimize the

Jan 1, 1944

By John Cogan

Field observations were made of rock phenomena in shale, dolomite, and fractured quartzite in the Burgin Mine, Eureka, Utah. Draft closure rates were measured with extensometers and convergence gages. In addition the effects of hydraulic props upon the retardation of closure was also monitored. Drift closure rates were found to be constant and to vary between 0.32 x 10-8 min-1 for dolomite and 23.8 x 10-8 min-1 for soft shale. The installation of props set at constant load served to retard the closure rates. General results show closure to occur at a constant rate for all cases, to be non-uniform around the drift openings, and to be increasingly retarded toward a zero rate by increases in prop load.

Jan 1, 1979

By Harold B. Goldman, Don Reining

The sand and gravel industry is the largest nonfuel mineral industry in the nation. In 1981, the production of sand and gravel totaled 755 million tons valued at $2.3 billion. California, which leads the nation with more than 110 million tons, together with Alaska, Texas, Michigan, and Ohio, account for 36% of the total production in the nation (Table 1). In commercial usage, sand applies to rock or mineral fragments ranging in size from particles retained on a No. 200 sieve (0.074 mm openings) to those passing a No. 4 sieve (4.76 mm openings). Gravel consists of rock or mineral fragments larger than 4.76 mm, ranging up to 88.9 mm (3 ½ -in.) maximum size. The construction industry consumes 97% of the sand and gravel produced; the remainder is sand used for specialized products such as glass (see the chapter on "Silica and Silicon"). Utilization The building industry uses sand and gravel chiefly as aggregate in portland cement concrete, mortar, and plaster; the paving industry uses sand and gravel in both asphaltic mixtures and portland cement concrete. Aggregate is commonly designated as the inert fragmental material which is bound into a conglomerate mass by a cementing material such as portland cement, asphalt, or gypsum plaster. Portland Cement Concrete Aggregates Portland cement concrete consists of sand and gravel surrounded and held together by hardened portland cement paste. Concrete mixes commonly contain 15-20% water, 7-14% cement, and 66-78% aggregate. Sand and gravel used as concrete aggregate have to meet many requirements (Goldman, 1956). Premature deterioration of concrete has been traced in many instances to the use of unsuitable aggregates. Asphaltic Aggregate Asphaltic mixtures used predominantly for paving consist of combinations of sand, gravel, and mineral filler (material finer than 0.003 in.), uniformly coated and mixed with asphalt produced in the refining of petroleum. Except for the addition of mineral filler, sand and gravel used as asphaltic aggregate must meet the same general physical requirements as materials used for portland cement concrete aggregate. General Requirements of Aggregates Construction aggregate has many requirements that are difficult to meet if only unprocessed material from natural deposits is used. Suitable material is composed of clean, uncoated, properly shaped particles which are sound and durable. Soundness and durability are terms used to denote the ability of aggre- [ ]

Jan 1, 1983

By E. S. Machlin, S. Weing

GRAIN boundary stress relaxation has been the subject of several investigations in recent years, but as yet the phenomenon is not well understood. One of the major difficulties has been the lack of a sufficient amount of data with which to evaluate any proposed mechanism. Little information is available on the effect of small amounts of substitutional solutes on grain boundary stress relaxation. It is with this important phase of the problem that this investigation is concerned. The influence of substitutional solutes on grain boundary stress relaxation has been recently investigated in copper by Pearson: and in aluminum by Dorn et al.' Pearson studied the effect of zinc, gallium, germanium, and arsenic on the relaxation peak of OFHC copper.* The pure OFHC copper decreased the peak intensity and a second peak appeared at a higher temperature. This latter peak was termed the alloy grain boundary peak. At the lowest binary concentration studied, approximately 1 atomic pct, the primary peak was almost completely obliterated. Pearson found that the activation energy calculated from the alloy grain boundary peak for all solutes, irrespective of the concentration, was 44,000 cal per mol. Pearson concluded that the increase in activation energy from 33 to 44 kcal per mol is not continuous but abruptly changes from the lower to the higher value. As no attempt was made to investigate the intermediate range of concentration and hence calculate the possible variation of the activation energy for the initial grain boundary peak, this conclusion is hardly valid. In contrast to these results, Dorn et al. studied the effect of zinc, silver, copper, germanium, and magnesium on the grain boundary stress relaxation of aluminum. No change in the energy of activation was observed for binary alloys of the flrst four solutes, but a linear increase was found for increasing concentration of magnesium. Saturation was not found up to the maximum of 1.6 atomic pct. The energies of activation were obtained by plotting the horizontal displacement of the dynamic modulus curve vs temperature for two vibrational frequencies. As the modulus is proportional to the square of the frequency, this requires the measurement of the torsional frequency over a range of temperature. However, the technique does not lead to an unambiguous interpretation of the grain boundary

Jan 1, 1958

By J. H. Fletcher, S. M. Cassidy

Air has been cooled, heated, washed, humidified and dehumidified for many purposes and in many industries. At a number of metal mines air is conditioned to reduce the high humidity and unbearable heat found in deep workings, and at some mines air is washed to allay siliceous dust. Steam is introduced into the intake air at many coal mines, particularly in winter, for the purpose of keeping loose coal dust so moistened that the hazard of an explosion is lessened. This paper will describe a further successful application of air conditioning in a coal mine, where, for over three years, all intake air has been cooled to a constant temperature for the sole purpose of preventing roof falls. Effect of Warm Weather on Mine Roof It is generally known by mining men that some, if not all, coal mines have more trouble from bad roof during the warm summer months than in winter. Also, it has been observed that roof on intake airways is usually worse than on the return entries, after the air has circulated through the mine. Some mines and some coal seams are much more affected than others. In the Clinton district of Indiana, the No. IV coal seam has a good, firm, gray shale roof except during the summer months, when it deteriorates badly and falls in small slabs 1 to 6 in. thick. Timbering is not very efficacious during this period because in time the roof will shear around the supporting prop or crossbar and either dislodge the timber or leave it supporting only a few inches of crumbly shale (Fig. 1). This action is renewed each summer, choking airways with fallen slate, tearing down trolley wires, hampering haulage, endangering men and adding considerably to the deadwork cost. Only when mines have been worked for a period of years and have been advanced a long distance from the shaft do the active workings become comparatively free of this trouble, and even then the intake entries are still a source of much deadwork. Such was the annoying situation at the mine of the Saxton Coal Mining Co. operated in the No. IV coal just north of Terre Haute, Ind. During the months of warm weather it was possible to stand at any quiet spot in the mine and within 10 min. hear at least two or three falls,

Jan 1, 1931

By L. A. Roe

The flotation of fine particles less than five microns in diameter and the flotation of liquids from liquids generally requires bubble generation methods different than methods used in dispersed air type machines used in mineral flotation. Conditions in the separatory zone in mineral cells are generally more dynamic as compared to the quiescent conditions often absolutely necessary for the flotation of fine particles and liquids. An example of quiescent flotation with very fine bubbles is the lithium flotation plant which operated at Trona, California for 34 years, until it ceased operations in 1978. A review of the process development and the commercial flotation operations at Trona is given in this paper. The clarification of oil field brines by flotation of the oil from the brine has been used for over twenty-five years. Recent installations related to the Prudhoe Bay oil field and the Alaska pipeline are described.

Jan 1, 1980

By J. D. Miller, A. Cortez, J. Hupka

The separation efficiency of the hot water digestion-flotation technique used for bitumen recovery from various domestic tar sands was evaluated. Bitumen viscosity was found to be the most important tar sand property in determining the success of the bitumen separation. Bitumen viscosity of the tar sand war controlled by changes in digestion temperature and/or changes in diluent (kerosene) addition. Complete and uniform dilution of the bitumen phase was achieved by providing a sufficient presoaking, or penetration time, for a given tar sand type. For all the tar sand samples tested, an excellent correlation was obtained between the coefficient of separation and the bitumen viscosity. To achieve a satisfactory coefficient of separation, it was found that the bitumen viscosity must be reduced below 1.5 Pa.s (16 P) at the temperature of digestion. This was the case regardless of the tar sand type, grade, or origin.

Jan 1, 1984

By J. D. McBeth, G. M. Potter, Ramon Pizarro

Heap leaching is used by the Carlin Gold Mining Co., Carlin, Nev., to supplement conventional processing of gold ore by agitation-leaching and countercurrent decantation. Selected open-pit ore containing about 0.072 oz Au per ton is crushed to 3/4 inch, dumped by truck on an asphalt pad, and leached by sprinkling with dilute cyanide solution for 7 days. The heap is then drained and removed by front-end loader to tailings disposal. About 70 percent of the gold is dissolved. Leach solution from the heap joins the pregnant solution from countercurrent decantation for gold recovery by zinc precipitation. Four leach pads, each with a capacity of 1,400 tons of ore, are in use. About 10,000 tons of ore are heap leached monthly from about April through October. Heap leaching is recessed during freezing weather. Labor, equipment, and reagent requirements for heap leaching are presented.

Jan 1, 1974

Each spring most secondary schools select their best student science exhibits, prepared during the preceding academic year, and send them to regional "Science Fairs", which now number over 220. Winner-finalists of these regional contests are then sent to the annual National Science Fair, conducted by Science Service, a non- profit institution for the popularization of science, for final judging. (The Fair is now known as the "National Science Fair-International" because of participation by finalists from Japan, Thailand, Germany, France, Sweden and Canada.) For the first time since the Fair was started in 1950, AIME participated in the awards presentation. Held this year in Baltimore, Md., from May 5 to 9, five members of AIME's Washington, D.C., Section consented to represent the Institute as judges. They were: Marlin J. Ankeny-Director, Bureau of Mines, U.S. Department of the Interior. Kenneth N. Weaver-Director, Maryland Department of Geology, Mines, and Water Resources. William Harper-American Petroleum Institute. Vice-Chairman, Washington Section, AIME.

Jan 7, 1964