Search Documents

By E. W. Murbach

The oxidation of uranium carbide by oxygen at various pressures, and by air, has been investigated at temperatures up to 600°C. Arc-melted and cast uranium carbide displays oxidation behavior that appears to be dependent on its treatment after melting. ccReactive" uranium carbide, which results from exposure of freshly melted material to laboratory air, ignites in oxygen at about 275° to 350°C depending on pressure, and in air at about 350°C. The product of the initial oxidation appears to be UO2+.. Continued heating produces U30,. The initial oxidation rate is poportional, roughly, to the square root of the oxygen pressure. The activation energy determined for the initial oxidation reaction is 7.1 kcal, from 400° to 600°C in 10 mm of oxygen. AN investigation of low-decontamination methods for reprocessing uranium carbide reactor fuels is being carried out at Atomics International. One of the reprocessing cycles includes oxidation of the fuel at relatively low temperature (300° to 500°C) and reaction of the product oxide with carbon at elevated temperatures (above 1500°C) to produce uranium carbide. A number of small-scale experiments have been carried out in which uranium carbide was oxidized in air and oxygen at various pressures to measure reaction rates and to obtain other information concerning the oxidation process. In initial experiments with arc-melted UC, ignition was observed at about 275°C in oxygen or 350°C in air. However, similar experiments by Neymark' at 426°C in air showed no ignition. It was soon determined that the difference in oxidation behavior was due to the treatment of the UC following arc-melting. Neymark's experiments were carried out with freshly melted UC while those reported in the

Jan 1, 1963

By Sherwin F. Kelly

FRONTIERS of geological knowledge retreated further this past year before an ever-widening geophysical attack, as governments and endowed institutions continued to take an increasing practical interest in the geophysical line of approach to the study of earth phenomena. A year ago I opened this annual review with a brief account of the efforts to discover what formations lie concealed beneath the deep sediments which form the superficial portions of the Continental Shelf off the eastern United States. That work was but the beginning, and 1938 saw its continuation and expansion. With the assistance of a Guggenheim Fellowship, Maurice Ewing pushed his researches in the development of instruments and techniques for deep-sea seismic refraction studies. Ewing's early refraction profile from the Virginia Capes to the edge of the Continental Shelf has been followed by a similar traverse in Great Britain from the coast of Cornwall to the edge of the Continental Shelf southwest of England. This showed that the thickness of the sedimentary mantle and the rates of slope of the basement surfaces there are comparable to those in the Virginia Cape district.

Jan 1, 1939

By Robert F. Mehl

PROGRESS in the general field of nonferrous physical metallurgy during the past .year has been uneventful but healthy. A continued increase is apparent in the number of useful alloys and in the mechanical treatment and heat- treatment of finished metals and alloys nothing can hinder the multiplication of alloys or the diversification of their treatment as knowledge of the behavior of .alloys increases; as ternary and quaternary alloys are better understood, hundreds of new metal combinations with unusual properties may well be expected. Evidence of rapid progress is already at hand.

Jan 1, 1936

By AIME AIME

THOUGH the Annual Meeting of the Institute-officially numbered 158 on the records was delayed a bit at the start by low steam pressure on the locomotives bringing members to New York, the crowd that finally arrived more than lived up to expectations, and the technical program had few difficulties because of absent authors or lack of competent discussers. The transportation difficulties were occasioned by the fact that Monday, Feb. 15, was the third coldest day in the 72 year history of the New York Weather Bureau, the official temperature being 8 below zero. The New York Central's premier train, the 20th Century, due at 9:30 a.m., arrived about 6:30 p.m., and the Commodore, another crack train from Chicago, was about equally late.

Jan 1, 1943

By Oliver Bowles

A HEAVY gel of bentonite clay has been proposed as an effective lubricant to speed down the ways to sea, river, or lake, the mighty cargo ships now hitting the water at the rate of about three a day. Another unusual application of a nonmetallic mineral is in food conservation, for the claim has been made that the next new item on the menu for poultry and rabbits will be vitamin tablets prepared from mont-morillonite clay. These uses have minor importance but illustrate not only the diversity in utilization, but the notable trend in 1942 toward mobilizing nonmetallic minerals for the war program. Although occupying less headline space than iron, steel, copper, aluminum, magnesium, and other metals, the nonmetallics are filling important emergency needs. Mica and quartz crystal are essential to communication; asbestos is urgently needed in fireproof heat and electrical insulation; and strontium minerals are utilized in the manufacture of signal flares and tracer bullets.

Jan 1, 1943

By Bunting S. Crocker

PEBBLE grinding at Lake Shore is not a temporary wartime substitute. The tube milling plant, with a 1000 ton per day capacity, grinds a hard siliceous ore to 90 pct - 325 mesh. The plant, prior to using pebbles, was consuming 4.3 lb of 1 1/4-in. grinding balls per ton of ore, which amounted to 785 tons of balls per year. At September 1951 prices, $132.60 per ton, this steel cost amounted to, $104,400 per year, or $0.285 per ton milled. By the Lake Shore method of substituting screened rock for this steel, all of this cost is saved. This is one of the major economies in Lake Shore mill practice. Regardless of the ultimate price of grinding balls, a change, back to steel balls is not considered. The present pebble plant is more flexible than a steel ball plant and equally efficient. For example, if it is desired to change the size of grinding media, the pebble charge in any mill can be changed completely in 4 to 5 days, as against 76 days to change completely a 1 1/4-in. steel ball charge. To change pebble size it is necessary only to change two sets-of screens and clean out the rock feed storage bin. This will take 8 to 10 days as against 3 to 4 months to clean. out the customary supply of grinding balls kept on hand. Also it has not always been ' possible to purchase all desired sizes of balls at any price. In an analysis of savings effected by the use of the pebble mills, the flexibility of the Lake Shore grinding plant should be discussed, as it has a direct bearing on these savings. The plant has always used several units to handle tonnage rather than sending all the tonnage through a single unit. This principle may result in using small diameter mills, but no objection to that is seen. At no time has any advantage been found in cost per ton ground in large diameter mills. Both the capacity and the power of any mill varies as the diameter raised to the 2.6th power. Consequently large or small mills are equally efficient, and a plant should be designed to use as many units-or combination of units as is consistent with reasonable operating practice. Mills under 5 ft diam are harder to reline, etc. To define the case at Lake Shore, .2600 tons per day formerly were milled in seven 7x6-ft ball mills and twelve 5x16-ft (and two 6x16-ft) tube mills.* This gave an excellent test plant. and an extremely efficient-one. In this plant the ratio of ball mills to tube mills was 1: 2. When the much cheaper pebble mills were substituted for the tube mills, this. ratio -was changed to one ball mill to four pebble mills to take the greatest possible advantage of the cheaper operating mill, i.e., the pebble mill. This flexibility without loss in efficiency has been an important item in the cost savings. It is interesting to note that the use of pebbles for fine grinding was. proved first in the laboratory in a 12-in. ball mill. In fact, since 1934 all testing on -.8 mesh material has been done in this 12-in. mill. Scope of the Tests A paper on fine grinding at Lake Shore Mines was published in July 1940.1 This paper covered 7 years of intensive research on fine grinding as well as sizing methods and equipment, plant scale grinding tests on 5x16-ft tube mills with and without .grate discharges-both with 1 1/4-in. and 3/4-in. balls, the use of laboratory mills to evaluate plant changes, and several reports on classifiers and classification. In the following July the addendum report' was added in which the idea of series-circuit grinding was introduced, and the results of running five stages of tube mills and bowl classifiers were shown. Since 1940, the ball milling end of the plant has been altered extensively as a result of tests on the use of 3 1/2-in. rods in 7x6-ft mills and the use of the Tyler repulping screen with from 7 to 14 mesh screens. These tests are, lengthy and may be covered in a separate 'report later. The scope of this report is confined to ore ground by rod milling and ball milling until it passed through an 8 mesh Tyler Ty-rod screen. The -8 mesh screen undersize then was pumped to a primary bowl classifier in open circuit and the sands .from the bowl sent to the primary pebble mills, see Fig: 1. In the pebble mill circuit the ore is ground to 90 pct -325 mesh (24 pct + 28 microns) In studying the flowsheet, attention should be paid to the efficiency of the classification equipment used. The Tyler repulping screen is an efficient machine on the 8 to 10 mesh separation, and the bowl classifier is equally efficient at the 325 mesh separation. Efficient classification is a necessity for series-circuit stage grinding. The ore is hard siliceous porphyry, 60 pct SiO2, 80 pct insoluble. Its grindability at different. meshes has been shown near the top of 'the list in F. C. Bond's grindability tests' Lake Shore is not shown, but an adjacent-mine with identical ore, Wright-Hargreaves, is. Reasons for the-Changeover Since 1936 grinding balls have been rising steadily in price with no sign of stopping. For a mill that used 4.5 to 5.2 lb of grinding balls for every ton of ore ground this rise represented an alarming increase in grinding costs. In many cases the quality of the grinding balls fell off as the scrap steel became more difficult to obtain. The ratio of tube mills to ball mills increased with the use of the Tyler repulping screen in the ball mill circuit. Originally only 3.0 lb of balls per ton were used in the tube mills, and this

Jan 1, 1952

By Theodore Marvin

NOW that real progress is being made in building airplanes that can stand up under adverse conditions in isolated parts of the world, utilization of aviation by mining and petroleum companies is proceeding rapidly. This isolation, offering such handicaps to ordinary methods of transportation, also was the thorn in the flesh of aviation until the recent advances in plane and englue design. The accompanying illustration shows one of the six new planes just delivered to the U. S. Government for map making. The planes will be used in Department of Commerce, Coast and Geodetic Survey, Navy Hydrographic, and Insular work. There is a trap door in the bottom of the hull for a Fairchild camera which takes five pictures-vertical, N60°, E60°, S60°, and W60°-at regular intervals. It is manufactured by the Grumman Aircraft Engineering Corp., Farmingdale, N. Y.

Jan 1, 1935

By H. Hubert

THE first attempts at direct utilization of blast-furnace gas in engines were made in 1895. For a considerable time the gas had been burnt in Cowper stoves for heating the blast for the furnace, and under the boilers which supplied steam to the blowing-engines, and others serving the furnaces. It was natural, therefore, that the idea of directly employing it in gas-engines should have occurred simultaneously to several engineers, notably to Lürmann and to Lencauchez, who had pointed out the blast-furnace as a powerful -gas-producer. Nevertheless, nowhere had any attempt been made to apply it to this purpose up to the end of 1894, when Thwaite proposed it to Mr. James Riley, of the Glasgow Iron & Steel Company. About the same time investigations were being made in Belgium and in Germany, independently of Thwaite's experiments, which were not generally known on the Continent. The industrial world, which up to that time had hardly favored the idea, had thus been gradually prepared to receive it. The gas-engine, long restricted to small sizes and dependent upon the use of an expensive fuel obtainable only in large centers, now began to make headway. At the Paris Exhibition of 1889 two engines of 100 h.p. were shown and excited much interest among engineers. One had four cylinders, and was made at the celebrated works of the Deutz Company, and the other was a single-cylinder engine, exhibited by two French designers, Messrs. Delamare-Deboutteville and Malandin. In the meanwhile the design of gas-producers had made important progress, completely freeing the new engine from its

Nov 1, 1906

By Bunting S. Crocker

EBBLE grinding at Lake Shore is not a temporary BlE wartime substitute. The tube milling plant, with a 1000 ton per day capacity, grinds a hard siliceous ore to 90 pct — 325 mesh. The plant, prior to using pebbles, was consuming 4.3 lb of 11/4-in. grinding balls per ton of ore, which amounted to 785 tons of balls per year. At September 1951 prices, $132.60 per ton, this steel cost amounted to $104,400 per year, or $0.285 per ton milled. By the Lake Shore method of substituting screened rock for this steel, all of this cost is saved. This is one of the major economies in Lake Shore mill practice. Regardless of the ultimate price of grinding balls, a change back to steel balls is not considered. The present pebble plant is more flexible than a steel ball plant and equally efficient. For example, if it is desired to change the size of grinding media, the pebble charge in any mill can be changed completely in 4 to 5 days, as against 76 days to change completely a 1-in. steel ball charge. To change pebble size it is necessary only to change two sets of screens and clean out the rock feed storage bin. This will take 8 to 10 days as against 3 to 4 months to clean out the customary supply of grinding balls kept on hand. Also it has not always been possible to purchase all desired sizes of balls at any price. In an analysis of savings effected by the use of the pebble mills, the flexibility of the Lake Shore grinding plant should be discussed, as it has a direct bearing on these savings. The plant has always used several units to handle tonnage rather than sending all the tonnage through a single unit. This principle may result in using small diameter mills, but no objection to that is seen. At no time has any advantage been found in cost per ton ground in large diameter mills. Both the capacity and the power of any mill varies as the diameter raised to the 2.6th power. Consequently large or small mills are equally efficient, and a plant, should be designed to use as many units or combination of units as is consistent with reasonable operating practice. Mills under 5 ft diam are harder to reline, etc. To define the case at Lake Shore, 2600 tons per day formerly were milled in seven 7x6-ft ball mills and twelve 5x16-ft (and two 6x16-ft) tube mills.* This gave an excellent test plant and an extremely efficient one. In this plant the ratio of ball mills to tube mills was 1:2. When the much cheaper pebble mills were substituted for the tube mills, this ratio was changed to one ball mill to four pebble mills to take the greatest possible advantage of the cheaper operating mill, i.e., the pebble mill. This flexibility without loss in efficiency has been an important item in the cost savings. It is interesting to note that the use of pebbles for fine grinding was proved first in the laboratory in a 12-in. ball mill. In fact, since 1934 all testing on — 8 mesh material has been done in this 12-in. mill. Scope of the Tests A paper on fine grinding at Lake Shore Mines was published in July 1940.' This paper covered 7 years of intensive research on fine grinding as well as sizing methods and equipment, plant scale grinding tests on 5x16-ft tube mills with and without grate discharges both with 1-in. and -in. balls, the use of laboratory mills to evaluate plant changes, and several reports on classifiers and classification. In the following July the addendum report2 was added in which the idea of series-circuit grinding was introduced, and the results of running five stages of tube mills and bowl classifiers were shown. Since 1940, the ball milling end of the plant has been altered extensively as a result of tests on the use of 3-in. rods in 7x6-ft mills and the use of the Tyler repulping screen with from 7 to 14 mesh screens. These tests are lengthy and may be covered in a separate report later. The scope of this report is confined to ore ground by rod milling and ball milling until it passed through an 8 mesh Tyler Ty-rod screen. The —8 mesh screen undersize then was pumped to a primary bowl classifier in open circuit and the sands from the bowl sent to the primary pebble mills, see Fig. 1. In the pebble mill circuit the ore is ground to 90 pct —325 mesh (24 pct + 28 microns). In studying the flowsheet, attention should be paid to the efficiency of the classification equipment used. The Tyler repulping screen is an efficient machine on the 8 to 10 mesh separation, and the bowl classifier is equally efficient at the 325 mesh separation. Efficient classification is a necessity for series-circuit stage grinding. The ore is hard siliceous porphyry, 60 pct SiO,, 80 pct insoluble. Its grindability at different meshes has been shown near the top of the list in F. C. Bond's grindability tests.' Lake Shore is not shown, but an adjacent mine with identical ore, Wright-Hargreaves, is. Reasons for the Changeover Since 1936 grinding balls have been rising steadily in price with no sign of stopping. For a mill that used 4.5 to 5.2 lb of grinding balls for every ton of ore ground this rise represented an alarming increase in grinding costs. In many cases the quality of the grinding balls fell off as the scrap steel became more difficult to obtain. The ratio of tube mills to ball mills increased with the use of the Tyler repulping screen in the ball mill circuit. Originally only 3.0 lb of balls per ton were used in the tube mills, and this

Jan 1, 1953

By Bunting S. Crocker

EBBLE grinding at Lake Shore is not a temporary BlE wartime substitute. The tube milling plant, with a 1000 ton per day capacity, grinds a hard siliceous ore to 90 pct — 325 mesh. The plant, prior to using pebbles, was consuming 4.3 lb of 11/4-in. grinding balls per ton of ore, which amounted to 785 tons of balls per year. At September 1951 prices, $132.60 per ton, this steel cost amounted to $104,400 per year, or $0.285 per ton milled. By the Lake Shore method of substituting screened rock for this steel, all of this cost is saved. This is one of the major economies in Lake Shore mill practice. Regardless of the ultimate price of grinding balls, a change back to steel balls is not considered. The present pebble plant is more flexible than a steel ball plant and equally efficient. For example, if it is desired to change the size of grinding media, the pebble charge in any mill can be changed completely in 4 to 5 days, as against 76 days to change completely a 1-in. steel ball charge. To change pebble size it is necessary only to change two sets of screens and clean out the rock feed storage bin. This will take 8 to 10 days as against 3 to 4 months to clean out the customary supply of grinding balls kept on hand. Also it has not always been possible to purchase all desired sizes of balls at any price. In an analysis of savings effected by the use of the pebble mills, the flexibility of the Lake Shore grinding plant should be discussed, as it has a direct bearing on these savings. The plant has always used several units to handle tonnage rather than sending all the tonnage through a single unit. This principle may result in using small diameter mills, but no objection to that is seen. At no time has any advantage been found in cost per ton ground in large diameter mills. Both the capacity and the power of any mill varies as the diameter raised to the 2.6th power. Consequently large or small mills are equally efficient, and a plant, should be designed to use as many units or combination of units as is consistent with reasonable operating practice. Mills under 5 ft diam are harder to reline, etc. To define the case at Lake Shore, 2600 tons per day formerly were milled in seven 7x6-ft ball mills and twelve 5x16-ft (and two 6x16-ft) tube mills.* This gave an excellent test plant and an extremely efficient one. In this plant the ratio of ball mills to tube mills was 1:2. When the much cheaper pebble mills were substituted for the tube mills, this ratio was changed to one ball mill to four pebble mills to take the greatest possible advantage of the cheaper operating mill, i.e., the pebble mill. This flexibility without loss in efficiency has been an important item in the cost savings. It is interesting to note that the use of pebbles for fine grinding was proved first in the laboratory in a 12-in. ball mill. In fact, since 1934 all testing on — 8 mesh material has been done in this 12-in. mill. Scope of the Tests A paper on fine grinding at Lake Shore Mines was published in July 1940.' This paper covered 7 years of intensive research on fine grinding as well as sizing methods and equipment, plant scale grinding tests on 5x16-ft tube mills with and without grate discharges both with 1-in. and -in. balls, the use of laboratory mills to evaluate plant changes, and several reports on classifiers and classification. In the following July the addendum report2 was added in which the idea of series-circuit grinding was introduced, and the results of running five stages of tube mills and bowl classifiers were shown. Since 1940, the ball milling end of the plant has been altered extensively as a result of tests on the use of 3-in. rods in 7x6-ft mills and the use of the Tyler repulping screen with from 7 to 14 mesh screens. These tests are lengthy and may be covered in a separate report later. The scope of this report is confined to ore ground by rod milling and ball milling until it passed through an 8 mesh Tyler Ty-rod screen. The —8 mesh screen undersize then was pumped to a primary bowl classifier in open circuit and the sands from the bowl sent to the primary pebble mills, see Fig. 1. In the pebble mill circuit the ore is ground to 90 pct —325 mesh (24 pct + 28 microns). In studying the flowsheet, attention should be paid to the efficiency of the classification equipment used. The Tyler repulping screen is an efficient machine on the 8 to 10 mesh separation, and the bowl classifier is equally efficient at the 325 mesh separation. Efficient classification is a necessity for series-circuit stage grinding. The ore is hard siliceous porphyry, 60 pct SiO,, 80 pct insoluble. Its grindability at different meshes has been shown near the top of the list in F. C. Bond's grindability tests.' Lake Shore is not shown, but an adjacent mine with identical ore, Wright-Hargreaves, is. Reasons for the Changeover Since 1936 grinding balls have been rising steadily in price with no sign of stopping. For a mill that used 4.5 to 5.2 lb of grinding balls for every ton of ore ground this rise represented an alarming increase in grinding costs. In many cases the quality of the grinding balls fell off as the scrap steel became more difficult to obtain. The ratio of tube mills to ball mills increased with the use of the Tyler repulping screen in the ball mill circuit. Originally only 3.0 lb of balls per ton were used in the tube mills, and this

Jan 1, 1953

By Elliot Rexford

The quality of aggregate materials is of major importance in governing durability and permanence of concrete structures. The problem of selecting suitable aggregate materials is two-fold. Geological factors include the type and character of the aggregate source, presence of known or suspected reactive constituents, and presence of thermally incompatible materials. Laboratory investigations include petrographic studies, soundness and reactivity tests, and tests of thermal properties. The importance of each factor in the selection of satisfactory aggregate material is considered in detail.

Jan 3, 1950

By Lysle E. Shaffer

INCREASING attention has been given in the last decade to the possibilities of mine leasing in the West. The practice as described in this article does not refer to the leasing of entire properties for corporate operation. It is intended to deal rather with the advantages and problems incident to leasing portions of properties to individuals who themselves, individually or in groups, do the actual mining and transportation of the ore. These individuals are sometimes called "leasers" and sometimes called "tributors." The contracts under which they work set up an independent relationship of lessor and leaser, between themselves and the mineowner or operator. This relationship has many advantages to both sides over those created by the ordinary relationship of employer and employe. From the standpoint of the owners there is no liability on independent contractors for industrial injuries, social security taxes, unemployment taxes, or the manifold restrictions of the Federal Labor Relations and Wage Hour Acts and similar state acts where they exist. As the leaser's income depends on the quantity and quality of ore produced, there is a distinct incentive for maximum production of a good grade of ore. This in turn promotes careful mining of the areas under lease. Ordinarily in mining, labor cost is a high percentage of the total cost of operation. Under a leasing system, even if the leasers be allowed to retain half of the gross values that they produce, and the owner or operator gets half, in the case of marginal ore bodies this is ordinarily more than the lessor would realize if the property were worked by day labor. In some instances mineral deposits under a leasing system may become ore, whereas under a day-labor system they would

Jan 1, 1948

By H. H. Stout

In the early fall of 1925, the writer was conducting, in the Ledoux and Co. laboratory, New York, experiments directed toward ascertaining the effect on its impurity content when cathode copper was subjected to a current of various gases at an elevated temperature below the melting point. The apparatus consisted of a vertical I-in. dia. silica tube about 12 in. long, heated on the outside. The cathodes were broken to pass 3/8-in. mesh, and a current of various different gases was passed up through a 4-in. long column of these loose cathode particles in the vertical tube furnace. Temperature was maintained to 1500º to 1600ºF. and the gas treatments lasted from 3 to 6 hr. The writer observed that whenever reducing gas (H2 or CO) was used, these cathode particles stuck together at points of contact with each other. The cohesion was so marked and tenacious that an examination was made of the fractured surfaces, when cathode particles were broken from the cluster. Crystal growth was always found to have taken place across the surfaces where separate particles were in contact, but only after all oxides, sulphates, etc., had been completely removed. The idea of a possible new process was then conceived and was disclosed to A. M. Smoot (V. P. Ledoux and Co.) with intent to obtain his views. The first conception as given Smoot was "to gas-clean broken cathodes, put them in an extrusion press, solidify and extrude them at around 1500ºF." Smoot's reaction, after a few moments considera- tion, was, "It looks perfectly all right to me.'' The writer and his assistants, W. H. Osborn and H. H. Stout, Jr., after conferring as to ways and means, decided to go ahead with preliminary laboratory experiments, which, it was thought, would move the new process from the possible to the probable. This program followed a course indicated by three basic considerations: 1. Since brittle cathodes were often unintentionally produced, it seemed probable that the laws controlling this type of deposition could be ascertained. 2. We had already proved the gas-cleaning feature. 3. There remained to prove: whether a sound, homogeneous metal billet could be produced with crystal growth established over the entire surface of each individual particle in the billet; and, if so, what would be the physical properties? Osborn arranged with Columbia University for conducting experiments in its research laboratory to prove or disprove the third item; Columbia assigned C. A. Phillipi, Jr. to assist in the project. A press with a cylinder 2 in. high and of I-in. dia. was used. It was surrouilded and heated by a resistance coil 01 Nichrome wire. Broken tough cathodes were used. Experimental Procedure The first run took place March 18, 1926. The resistance wire gave out when temperature of 1000ºF. was obtained. Pressure was immediately applied: perceptible ram movement stopped when 39,000 lb. per sq. in. on the copper was reached, with a maxi-

Jan 1, 1941

By Howard S. Bryant

FROM the viewpoint of the oil producer, the oil refiner, the oil marketer, and the investor, in oil securities, a brief picture of the crude oil supply and demand in the present critical season of the year will be timely and interesting. Although crude oil production has been in a comparatively poor statistical position this year, increased sales and sustained refinery and crude oil prices have allowed increased profits for many oil companies. The large amount of crude oil going into storage during the present period of peak consumption, just previous to the major yearly fall decline in consumption, has caused oil producers to make plans to leave the oil in the ground for the present in several of the areas of large flush production. The present moment is looked on as the turning point in the current year.

Jan 1, 1929

By AIME AIME

A. A. Holland, Consulting Engineer, Toronto, Ont.-I noticed in this discussion of locations in which radium is found, no mention is made of the recent deposits discovered in Ontario. While radium is not a subject with which I am very familiar, I took an interest in this deposit on account of its novel occurrence. It is found in Haliburton County, near Wilberforce, Ontario, associated with a quartz free pegmatite, in a "break" that I understand can be traced for two miles. This "break" marks the contact between the limestone and syenite and contains numerous cavities or vugs. The gangue, on account of its deep purple, appears to :be amethyst.

Jan 1, 1930

By Scott Turner

AS IN OTHER lines of engineering, progress in mining was influenced during 1931 by the world-wide economic depression. Low-metal prices ? resulted in active efforts to reduce production costs of base-metal mines. Probably the chief factors in reducing costs were the greater efficiency of labor, due to better relations between management and workmen, to the scarcity of jobs, reduced wages in most base-metal mines, and to lower overhead expenses secured by drastic economies. The use of mechanical equipment continued to increase, due to more efficient designs and a better practical understanding of the applicability of such equipment to requirements. With one exception, there were no startling innovations in stoping methods, but there was notable progress in the better adaptation of mining methods. In the United States, no large new base-metal or silver mines came into production during the year. At a number of mines, output was curtailed, and operations were discontinued at several important producers. On the other hand world-wide interest in gold was stimulated, as evidenced by increased output from producing mines, the reopening of some old properties, and intensive prospecting for new deposits. Mining methods at several gold mines in the United States and Canada were modified or changed to obtain a higher extraction of ore or to meet the need for additional support of the mine workings at depth. Permanent record of improvements in mining practices has been made during the year by the Federal Government; the industry thus has available for its use more detailed information than ever before. This work was done through cooperation of the mining companies and their representatives with the United States Bureau of Mines, whereby many papers descriptive of practices and costs at individual mines have been published. The Bureau's program of describing methods and costs at the more important mines (those producing in excess of $100,000 annually) is nearly completed, but papers will be issued concerning such additional mines as may possess particular interest because of novel methods, exceptional conditions or operating results, and others to supplement reports already issued. In this way, an interesting record of the results of changing conditions, or innovations in methods, will be made available.

Jan 1, 1932

By C. R. Dale

IT IS the purpose of this paper to point out a number of the most common causes of crooked holes; to outline methods of drilling and straightening which to my personal knowledge have proved successful in numerous cases; to describe some of the characteristics of holes which, though not crooked in an exaggerated sense, may still cause serious mechanical trouble if not recognized and properly remedied; and to define clearly the part of oil-well surveying in the concerted effort operators generally are making to keep their wells straight from spudding to completion

Jan 1, 1931

By Samuel S. M. Chan

The magnetic susceptibilities of some ores and the major rock formations of the Precambrian Belt Supergroup in the Coeur d'Alene mining district were determined both in the laboratory by the use of the Gouy method and in the field with a Bison susceptibility unit. Trace element analysis of the same group of rock samples was also made using the atomic adsorption technique. Results of this preliminary study indicate that some correlation exists between the magnetic susceptibilities and the various rock formations. This may be useful for regional mapping and mineral exploration.

Jan 1, 1974

By Hans Lundberg

GEOPHYSICAL methods as described in technical articles generally fail to answer the questions of prospectors and geologists as to which method they should apply and what information they may expect from their application. This article is an attempt to discuss the use of electrical methods with special reference to the prospecting for orebodies and the map¬ping of geologic structure. Especially on virgin ground, geological reconnaissance should precede electrical prospecting, with the object of outlining carefully the orebearing rock and determining the possibilities of elec¬trical prospecting. No electrical survey will then be carried out on ground which, for geological reasons, may be considered barren or where the electrical meth¬ods are inapplicable. As the success of electrical prospecting depends on the difference in conductivity between the ore and the country rock within which the orebody is inclosed, the conductivity of the two should be considered and de¬termined, if possible. The conductivity of an orebody depends on the distribution of conductive ore minerals and, in addition, on its size (length, width and depth). Most minerals with metallic luster show good electrical conductivity; for instance, the sulfides. Zinc-blende is an exception, but as it is often associated with the ore minerals of good conductivity (for instance, pyrite or galena), there is likelihood also of finding zinc.

Jan 1, 1930

By Albert Sauveur

As THE years go by, names of distinguished metallurgists will be added to the list of Henry Marion Howe lecturers, and now and then an illustrious one, for to be chosen to deliver the Howe lecture will be, I do not hesitate to predict, a highly coveted honor. I pray, therefore, your indulgence, if I confess to a feeling of gratification in having been appointed the first of these lecturers. It does not follow, however, that I am losing all sense of proportion and that I have an exaggerated idea of the little I have been able to contribute to our knowledge of iron and steel. Indeed, I fully realize how small were my claims to so great a distinction. I realize, also, that those entrusted with the task of selecting a lecturer were actuated, in coming to a decision, by their knowledge of the long and intimate friendship that had existed between the leader we have lost and myself. For their generous impulse, I thank them from the bottom of my heart; and with becoming modesty, I take up my task as the first Henry Marion Howe lecturer. It would be pleasant and indeed most appropriate to devote this entire lecture to a eulogy of Henry Marion Howe and his work, but how short the time for so large an undertaking and how inadequate my qualifications! On Aug. 28, Sept. 4, 11, and 18, 1875, a series of articles appeared in the Engineering & Mining Journal entitled "What is Steel?" With one exception, these constitute the first professional paper of Henry Marion Howe. That was nearly fifty years ago, three years after graduating from Harvard University. He was then but twenty-seven years old and already his keenly inquisitive mind was actively at work. There is a touch of romance in this young metallurgist who, on entering his. scientific career, destined to be so brilliant and so fruitful, on the very threshold of it, seems to have selected as his motto "What is Steel?" Like a knight-errant of science, he started on his quest for an answer to that question, a quest which was to last forty-seven years and which death only brought to an end. And while thus engaged how many wonderful messages we received from him, each one bringing us nearer to the goal! How illuminating, inspiring and encouraging were those messages! How well-equipped he was to wrench from nature some of the secrets she so jealously guards! How broad his learning and how clear his

Jan 5, 1924