Search Documents

By Frederick Laist, H. J. Maguire

The ore from the Butte mines of the Anaconda company is quite siliceous; that is, it contains considerably less iron than is needed for the fluxing of the silica. The direct smelting of this ore, therefore, requires the addition of considerable fluxing material. The only flux available in sufficient quantity at Anaconda is limestone containing no metallic minerals. This necessarily makes the direct smelting of the ore so expensive that it is more profitable to subject the ore to a preliminary treatment by concentration. However, as the losses in the concentrator were very high, compared with the losses in the blast furnaccs, it was found, by calculation, more profitable to send ores containing more than a given percentage of copper to the blast furnaces, in spite of the higher costs of treatment. The dividing point was dependent on various factors, the chief of which was the prevailing market price of copper. It was customary, therefore, to segregate the ore as mined into two classes. Ore in the first class generally contained 5 per cent. or over of copper; this was sent directly to the blast-furnace department. Second-class ore contained less than 5 per cent. of copper, and averaged around 3 per cent.; it went to the concentrating department. With the introduction of the flotation process, it mas found possible to maintain an average recovery, as concentrates, of 96 per cent. At the same time, the cost of reverberatory smelting was very materially decreased by the use of pulverized coal. These two changes in practice made the blast furnaces unable to compete with the reverberatory furnaces on a cost basis. The distinction between first- and second-class ore was therefore abandoned, and the ore was treated by concentration. Obviously, on ores as high in iron as the Butte ores, the concentrator produces a product that is self-fluxing; in fact, it is possible to produce a concentrate containing more iron than is necessary to flux the silica. Under these conditions, the amount of basic fluxing materials required for the smelting operations became very srnall and the converter slag lost its former value as a blast-furnace flux. For this reason, a less expensive method of recovering the copper, silver, and gold contained in it than smelting in blast furnaces had to be found. It was not feasible

Jan 1, 1921

By H. E. Wilborg

This chapter deals with those sands employed by the foundries for the manufacture of cores and molds used in the casting of such common metals as steel, gray iron, ductile iron, aluminum-based alloys, and copper-based alloys. Most metal is cast in "green sand" molds in which the sand mixture, consisting primarily of silica, clay, and water, forms a plastic material. This plastic material is rammed around a pattern in a split box called a flask, then the box is separated, the pattern is withdrawn, and the metal poured. These green sand molds are broken apart when the metal has solidified. The sand is then remixed and a new mold made for the next casting. To a lesser extent silica sand is mixed with resins or oils and, after forming, the mixture is hardened either by heat or chemical reaction. In any case, the foundry mold or core is used just once before being broken up and remixed for manufacturing another core or mold. By far the greatest consumption in the foundry is of those types of sand high in silica, low in clay (under 0.5%) and occurring in numerous locations thoughout the United States.

Jan 1, 1975

By Robert H. Richards

Walter Renton Ingalls recently gave a very interesting talk before the student mining society of the Massachusetts Institute of Technology. In it he showed the present status of mining as he sees it. In the talk he explained that, while discoveries of great mining districts are still pssible, they are being made less and less often; that the great mining companies, although there are large numbers of mines offered for sale, are finding it less and less possible to find new mines that are up to the standard of richness that they wish for purchase. The natural conclusion is that better, cheaper, and more efficient methods of mining, concentrating, and smelting are needed if the lower-grade mines are to be worked at a profit. This is true also if the high-grade mines are to yield their greatest profit. This paper deals only with the concentrating or ore-dressing problem, and gives some thoughts which point towards greater profit. In a paper on The Development of Hindered-Settling Apparatus the writer showed that there were two main lines of work that would lead to greater saving, lower tailing assay, and, therefore, greater profit. The first is the recrushing of middling or tailing products for the saving of the contained values. This is well understood and largely carried out in existing mills. The second is the saving of fine free mineral at the first opportunity. This is a matter less well understood in the mills, and to dwell upon this the present paper is written. The writer is himself convinced and hopes to convince the reader that, for obtaining the above result, not only is better classification needed, but also more classification; that is, there should be more spigots or pockets to the classifier. His attention was recently called to a small mill which had a three-pocket cone classifier fed with from 2 to 0 mm. stuff, supplying feed to four Wilfley tables. The first spigot had about all the

Jan 1, 1914

By Newell G. Alford

Forecasts of future timber consumption in soft-coal mining are handicapped by the lack of adequate experience records for estimating properly the timber requirements of the industry. Data were obtained from plants where records are kept or from operators who collected the information and to these were added composite figures for the continental United States in 1905 and 19191 and for central and western Pennsylvania and for Illinois in 1922.2 The result, representing slightly over 928,000,000 net tons, is shown in Table 1. Some of the companies furnishing data were unable to segregate the timber into classes of use but for those who did, Table 2 shows the board feet of posts and cross ban used per ton of coal mined and the percentage of the total timber consumed that was used in roof support. The wide variation in amounts of timber per ton of coal mined is the result of

Jan 1, 1924

By John J. McCabe

INTRODUCTION Over the years, Congress has written into the Internal Revenue Code various provisions aimed at lessening at least one financial burden faced by taxpayers in the mining industry - the federal income tax burden. These provisions include the election to deduct exploration expenses, the election to defer deduction of development expenses, and the percentage depletion deduction. Careful tax planning from the very beginning of a mining venture is essential in taking maximum advantage of these tax benefits. A major decision to be made is the choice of organizational structure. (For a more detailed discussion of this subject, see McCabe, John J., "Developing Structures for Investments in Mineral Property," New York University Institute on Federal Taxation, 42 NYU 24, 1984). One such structure is the use of multiple corporations, with mining activities conducted by one corporation and nonmining activities, such as manufacturing, financing and administration, conducted by the other corporation. This technique, which will be discussed in detail below, can be particularly advantageous in delaying recapture of previously deducted exploration expenses and in maximizing depletion deductions. TAX BENEFITS IN MINING Exploration Subject to certain restrictions discussed below, exploration expenditures (i.e., expenditures paid or incurred during the taxable year for the purpose of ascertaining the existence, location, extent, or quality of any deposit of ore or other mineral, and paid or incurred before the beginning of the development state of the mine are deductible at the election of the taxpayer (Section 617(a)).* Were it not for this option, exploration expenditures would be required to be capitalized and recovered through depletion, after production begins. Exploration of a mineral deposit can be very costly and may not result in commercial production for some time. If the taxpayer has income to he offset by the deductions, a mining venture can usually be structured in such a way as to allow the offset of mining losses against the other income. With today's high interest rates, this election can be quite valuable in present value terms. Corporate and noncorporate taxpayers are subject to different restrictions on this tax benefit. Corporations may elect to deduct only 85 percent of eligible exploration expenditures (Section 291(b)). (The Tax Reform Act of 1984 reduced this to 80 percent effective for expenditures after December 31, 1984, in taxable years ending after such date). The remaining 15 percent (20 percent after December 31, 1984) is capitalized and recovered at the same rate as five-year ACRS property (Section 291(b)). Individual taxpayers are not subject to this 85 percent rule; however, any amount deducted in excess of ten-year straightline amortization is a tax preference item for individuals (Section 57(a)(5)). Individuals may avoid the tax preference by electing to capitalize exploration expenditures and amortize them over ten years (Section 58(i)). In order to prevent the taxpayer from, in effect, converting ordinary income into capital gain by selling property that has given rise to exploration expense deductions, the Code requires recapture of such deductions upon the occurrence of certain events (Section 617): 1. Upon disposition of the property, adjusted exploration expenditures are recaptured to the extent of gain realized on the disposition (Section 617(d)). 2. If the property is leased, the lessor is disallowed any depletion deduction until his adjusted exploration expenditures have been recaptured in the form of foregone depletion deductions (Section 617(c)).

Jan 1, 1985

By W. L. Crentz, E. E. Donath, D. Doherty

Maurice Rey—The influence of cyclone diameter upon the fineness of separation is an important point which, however, cannot be discussed adequately if the injection pressure or the rate of flow are not specified. Perhaps some light can be thrown on the matter by using the formulas derived by Dahlstrom. Let us consider several geometrically similar cyclones where the apertures e and b are equal and proportional to the diameter D and which are operated with the same pressure drop. Eq 8 of Dahlstrom's paper can be written: Q Q = K D'. " or. if F is constant: Q = K D18 K is a constant of proportionality. Introducing this value of Q in eq 13 gives elimination efficiency = K D0' " Elimination efficiency, in the terminology of Dahlstrom, means the diameter of particles, in microns, which divide equally between the underflow and the overflow. This denomination is regrettable and it would be preferable to call it diameter of separation or characteristic size or any other name connoting a size rather than an efficiency. Whatever the name used, the above equation shows a slow increase in the fineness of separation when the diameter of the cyclone decreases. For example, if a 14-in. cyclone gives a 400-mesh separation (37 microns), geometrically similar cyclones, having the same pressure drop will give separations at the sizes shown below.

Jan 1, 1951

By E. E. Donath, W. L. Crentz, D. Doherty

Maurice Rey—The influence of cyclone diameter upon the fineness of separation is an important point which, however, cannot be discussed adequately if the injection pressure or the rate of flow are not specified. Perhaps some light can be thrown on the matter by using the formulas derived by Dahlstrom. Let us consider several geometrically similar cyclones where the apertures e and b are equal and proportional to the diameter D and which are operated with the same pressure drop. Eq 8 of Dahlstrom's paper can be written: Q Q = K D'. " or. if F is constant: Q = K D18 K is a constant of proportionality. Introducing this value of Q in eq 13 gives elimination efficiency = K D0' " Elimination efficiency, in the terminology of Dahlstrom, means the diameter of particles, in microns, which divide equally between the underflow and the overflow. This denomination is regrettable and it would be preferable to call it diameter of separation or characteristic size or any other name connoting a size rather than an efficiency. Whatever the name used, the above equation shows a slow increase in the fineness of separation when the diameter of the cyclone decreases. For example, if a 14-in. cyclone gives a 400-mesh separation (37 microns), geometrically similar cyclones, having the same pressure drop will give separations at the sizes shown below.

Jan 1, 1951

By R. M. Daelen

Mechanical science is severely tested by the demands of the iron manufacture for the varied apparatus needed to transport and to treat raw materials and products. Water has long been a favorite means of transmitting pressure for such purposes, because of its own incompressibility. Further advances in its use are the more to be expected, since mechanical improvements have steadily tended to overcome the difficulties formerly encountered in the employment of great hydraulic pressures. So long as the pressure is not higher than that which requires for plungers, etc., only ordinary stuffing-boxes, with hemp or other similar packing, the necessary arrangements for the production and transmission of the water-pressure without leakage are very simple. But when this limit (which is, for most purposes, 50 kilos to the square centimeter) is exceeded, new conditions of construction arise, which are met in various ways, and which justify a primary division of hydraulic presses into low-pressure and high-pressure respectively. The former are used in lifting and moving weights, and employ pressures as high (in extreme cases) as 100 kilos per square centimeter; but at this point the friction between piston and hemp-packing is so great that the use of cup-leathers is already preferable. Beyond 100 kilos it becomes a necessity. The range of practicable tight packing which follows is considerable, extending to about 1000 kilos; but "high pressure" in practice is from 100 to 600 kilos, and it is to this that the present paper applies. General Classes and Types. Hydraulic transmission at high pressure usually claims consideration in case the solid mechanism, such as levers, cams, screws, and gear-wheels, would have to be too large, would involve too much friction, or could not be suitably adapted to the speed-requirements of the working-tools. Since steam is mostly the primary carrier of

Jan 1, 1893

By C. J. Rosa, W. C. Hagel

An attempt is made to determine the diffusion coefficients of oxygen ions in hypostoichiometric zirconium oxide. A phenomenological theory is developed for three-phase, unidirectional volume diffusion of a gaseous species from a planar source. Knowledge about oxygen diffusion in a and ß zirconium and experimentally measured rates of movements of interfaces permit the evaluation of oxygen ion diffusivi-ties in ZrO2-x. The results conform to the relationship: sq cm per sec, for the temperature range of 875" to 1050° C. DIFFUSION coefficients of oxygen ions in stoichio-metric oxides have been studied by many investigators. The obtained results not only supplement the knowledge about the lattice-defect structures of oxides and conduction mechanisms but also provide information of technological importance. Rate processes such as oxide sintering, high-temperature creep deformation, and oxidation of metals and their alloys are directly dependent on diffusion phenomena. Unfortunately, diffusion coefficients obtained from studies on stoichio-metric oxides cannot be treated without restraints when applied to oxidation kinetics, if precise evaluations of oxidation rates are desired. Oxides formed on metals are usually nonstoichiometric and exhibit nonuniform distribution of either cation or anion vacancies across their thicknesses. Debuigne and Lehr1 extended Danckwerts'2 mathematical analyses and furnished a semitheoretical treatment for evaluating oxygen diffusion coefficients in zirconium oxide in terms of weight gain measurements during oxidation of zirconium in the temperature range 400° to 850°C. Their calculations are based on theoretical partitioning3 of the total amount of oxygen between a zirconium and its oxide phase. An inherent discrepancy appears to continue throughout their calculations. The amount of oxygen confined to the oxide phase should be corrected by multiplying the calculated oxide thickness by the inverse of Pilling-Bedworth ratio, if expansion of zirconium dioxide is taken into account. The purpose of the present investigation is to provide a new semitheoretical treatment for evaluating diffusion coefficients of moving species in hypostoichiometric oxide. The analyses are relevant to unidirectional volume diffusion. Although the presented method is quite general, its applicability will be discussed in terms of kinetic measurements from oxidation of zirconium at temperatures above the a/ß transition, for reasons stated in the later part of this paper. EXPERIMENTAL Pure, 99.93 wt pct, zirconium samples of approximately 2 by 1 by 0.35 cm were exposed to oxygen for various times at four temperature levels: 875°, 950°, 1000°, and 1050°C. High-purity, better than 99.9 vol pct oxygen was passed through a cold trap and columns containing anhydrous CaSO4 to remove residual water vapor. Before exposing to oxygen at a pressure of 500 Torr, specimens were subjected to wet abrasion on 200- through 600-grit Sic papers and polished with 1—p diamond dust. Prior to oxidizing, all zirconium samples were vacuum-annealed at 10-6 mm Hg for about 15 min at the test temperature. The temperature variation across the uniform heat zone was ±2°C from the preset value. Final polishing, for phase thicknesses measurements, was performed by using 8- and 1-p diamond dust and followed by vibrator polishing with 0.05-µ ? Al2O3 solution. Measurements of phase thicknesses were made by projection on a metallographic viewing screen. Conventional powder X-ray analyses for the oxide were employed. RESULTS Fig. 1 is an example of the cross section of oxidized zirconium. Designations of phases given below this figure are the same as those used in the three-phase diffusion system represented by Fig. 5 in the following section. Zirconium oxidized for longer exposure times showed two types of oxides: white oxide at the surface and an underlaying layer of gray oxide. X-ray powder patterns of these oxides at room tern-

Jan 1, 1969

By John D. Ridge

For mining geologists, the most important trends during 1962 have been the increased concentration of the exploratory activities of American mining companies in the United States and Canada and the greater use of the combined techniques of geology, geophysics and geochemistry in searches over larger areas for wider varieties of metals and minerals. The principal reasons for these changes in approach have been the deterioration of the political-economic climate in many areas of the globe of equal or greater geologic promise and the realization that modern exploration is most efficiently and economically conducted through the use of all available means of detecting ores in areas sufficiently large to raise to a maximum the chances of success. The attitude of certain major U.S. metal-producing companies can be shown by the officially ex- pressed positions of their principal officers. Early in 1962, Clyde E. Weed, Chairman of the Board of Anaconda, remarked that "because of unsettled conditions and disruptive influences in many of the copper-producing areas of the world, it is imperative that domestic copper-producing capacity be improved and made as efficient as possible in order to meet consumer demands at reasonably stable prices." In November, Robert G. Page, President of Phelps Dodge, pointed out that his company is not only concentrating most of its exploratory effort on this continent but is also increasing the number of metals for which it is searching. Frank R. Milliken, President of Kennecott, recently said that "most of our exploration money is going into the northern part of the Western Hemisphere."

Jan 2, 1963

By A. W. Griffith, R. G. Beverly, W. A. Millsap

THE Grand Junction Pilot Plant, operated by National Lead Co. Inc., for the U. S. Atomic Energy Commission, is engaged in the amenability testing of orebodies to establish design and cost data for commercial mills and to test new processes for recovery of uranium from ores. Test work was performed to study the effects of several variables on leaching of uranium ores in carbonate solutions. Many of these variables had been investigated in the laboratory, but pilot plant tests were desirable to evaluate their importance in semi-works equipment and to predict optimum operating conditions for future commercial mills. The results of these tests should serve as a guide in selecting the most efficient and economical method of leaching uranium ores amenable to a carbonate process. This article is concerned with a process in which uranium is extracted from the ore by a hot Na2CO3- NaHCO3 solution; the uranium-bearing solution is separated from the solid residue by filtration, and uranium is then precipitated by chemical means.

Jan 9, 1957

By G. Birkbeck, T. C. Wells

Pearlite morphology in three commercially produced, low-carbon steels has been studied using optical and electron microscopy. A reduction in the cooling rate from 600° to 6°C per hr increased the interlamellar spacing but had little effect on pearlite content. The form of the lamellae was also assessed in terms of a new parameter, the ratio of lamellae length to interhmellar spacing. The variation of this parameter with cooling rate depended on steel composition. For each steel, it would appear that an optimum cooling rate exists at which lamellar pearlite can be produced to the greatest extent, though not necessarily the same extent in different steels. PeARLITE morphology depends principally on steel composition, prior austenite grain size, and either cooling rate or isothermal transformation temperature. Alloying with manganese,'" fine grain size,374 and slow cooling rates reduce the likelihood that a well-developed lamellar structure will be produced. Instead, imperfect structures usually consisting of partly globular carbides are formed in a ferrite matrix. Such structures have been described as granular.1,2,5 degenerate,6 or semi4-pearlite. Manganese additions also progressively lower the eutectoid temperature and the carbon concentration at the eutectoid so so that, for a given carbon content. the pearlite fraction is increased as manganese is added. While the effects of manganese are understood in a general way, quantitative studies of pearlite morphology have been carried out mainly on steels of eutectoid composition;9 little quantitative data is available for low-carbon steels. Certain anomalies exist in the behavior of steels containing -1.5 pct Mn, however. The pearlite morphology in niobium-treated steel differs from that which is generally accepted as typical of low-carbon/manganese steels in that a reasonably well developed lamellar structure is sometimes observed. In the present work, the effects of changes in cooling rate from 600° to 6°C per hr on the pearlite morphology in three commercially produced, low-carbon steels have been studied by both optical and electron microscopy. I) MATERIALS The steels were of the following types: 1) 0.1 pct C, 0.4 pct Mn steel (En 2, a composition similar to specification SAE 1010); 2) niobium-treated, 0.2 pct C, 1 1/2 pct Mn steel (BS 968:1962); 3) silicon-killed 0.2 pct C, 1 1/2 pct Mn steel (En 144, a composition similar to SAE 1320). The chemical analysis for each steel is given in Table I. To facilitate the comparison of pearlite morphology in the three steels, steels 1 and 3 (which were obtained as 1/2-in. plate and 1-in.-diam bar, respectively) were hot-rolled in the laboratory to $ in. thickness, finishing at around 850°C. The BS 968:1962 was received as 1/8-in. plate finished at 885°C and was not further worked. Specimens from each steel were heat-treated in vacuo at 950°C for 1 hr and cooled at rates of 600°, 60°, and 6°C per hr. 11) EXPERIMENTAL Pearlite contents were determined by point counting (500 points) on longitudinal sections mechanically polished and etched in 2 pct nital. Pearlite morphology is usually considered in terms of interlamellar spacing. For pearlite colonies randomly distributed in space and having a true, constant interlamellar spacing So Pellissier et al.9 determined the distribution curve for the apparent spacings of the lamellae on a random section plane. The areal fraction fs of the pearlite colonies occupied by apparent spacings up to a limiting value S is given by:

Jan 1, 1969

By John Mathews

IT is twenty years since the writer made his first molybdenum steels and others were making them commercially five years earlier but the prevailing opinion seems to be that molybdenum steels are new; from time to time the daily press speaks of important discoveries in Europe and intimates that American steel makers have much to learn in regard to alloy steels. The earlier experiments were largely confined to the use of relatively high percentages of molybdenum in tool steels and permanent magnet steels. Recent developments deal with the types of alloy structural steels used for airplane, automobile, and other engineering requirements; in these, the molybdenum content is usually less than 1 per cent. The earlier types generally have been unsuccessful commercially, but the newer types of steels are becoming of increasing importance. The war showed our dependence on foreign sources for alloying metals; molybdenum alone is widely distributed in the United States and seemingly abundant. Many deposits are not now of commercial interest, owing to location and relatively small amount of ore available, but other deposits are being developed and a stable source of supply seems well assured. In tool and magnet steels, it was early found that 1 part of molybdenum was equivalent to from 2 to 2.5 parts of tungsten. The permanent magnet steels investigated by Madame Curie,1 in 1898, contained from 3.36 to 4.05 per cent. molybdenum; in 1902, Dr. E. L. French and the writer thoroughly tested steels containing from 2:0 to 4.0 per cent. These steels gave satisfactory tests for permanence, but were low in residual density and much more sensitive to hardening than the corresponding tungsten products. We discontinued work with them, therefore, and have no advice that such steels have been used commercially here or abroad.

Jan 2, 1921

By R. C. Thompson

THE lead-zinc mill of Phelps Dodge Corporation, Copper Queen Branch, Mines Division, Bisbee, Arizona, is about 3 miles from the main hoisting shafts of the Junction and Campbell mines at Lowell. All the ore treated in the mill is obtained from these two mines. The mill was designed for an all-flotation treatment of 450 tons of lead-zinc ore per day, and has been operated at that capacity since the start of milling operations on Nov. 17, 1945. An expansion program is underway whereby the mill capacity will be doubled, but this article describes only the original program and presents results of the 45o-ton operation. GENERAL DESCRIPTION The milling plant consists of an ore-receiving bin and three steel-constructed buildings housing, respectively, the primary crushing equipment, the secondary crushing equipment, and the ore-storage bins, grinding, flotation, and filtering equipment. The mill site is the one that was used for a previous copper-concentrating plant, which was operated over a period of years and then dismantled. There remained from this operation some milling equipment, a reservoir for mill-water supply, railroad tracks, tailings-disposal ponds, and a steel-constructed building, all of which were incorporated in the design of the present lead-zinc mill. The location plan of the plant layout is shown in Fig I. The flowsheet of the mill is based on the conventional scheme for lead-zinc treatment, however, several innovations were made necessary in order to utilize the existing building. Placing of equipment also was governed by the design of the building; thus making the mill unique in many respects. The following brief description of the mill building as adapted to the flowsheet points out the compactness of the installation and some of its unusual features. The first floor (Fig 2) houses the grinding equipment, with connecting conveyors for ore feeding, also an air compressor, two vacuum pumps, bins for lead and zinc concentrate storage with individual conveying systems for loading the two kinds of concentrates. Filtering of concentrates is done on the second floor, the concentrates discharging directly into the concentrate-storage bins. On this floor are the lead and zinc filters, two diaphragm pumps, sample-filtering equipment, sample-preparation room and a change room for the mill employees. The flotation machines are on the third floor, at elevations allowing a gravity flow of the lead and zinc concentrates to the thickeners. The annex to the building contains a freight elevator and provides space for all reagent mixing and feeding, also storage of reagents and grinding balls. All the water used for milling purposes is pumped from the Junction mine and

Jan 1, 1947

By David P. Hale

THE Cartersville barite district is near Cartersville, Ga., in the southeastern part of Bartow County, about 43 miles northeast of Atlanta. The area over which active mining is being done extends about six miles in a northeasterly direction and is about three miles wide. Barite production in Georgia began about 1907,1but the existence of the mineral was known much earlier. At present four companies are operating washing plants and three other plants are operating on leases from those companies. The chief impurities in the ores are silica and iron oxide. The silica is easily washed and jigged out and gives little trouble. Any gravity separation between the iron and the barite is generally poor, owing to the slight difference in specific gravity. Two operators have turned to magnetic separation as the solution to the problem and have made remarkable improvements in the finished product. By very close sizing prior to jigging, the separation between iron and barite has been greatly improved. In some localities manganese occasionally appears as an impurity, but is fairly easy to eliminate by gravity methods. A considerable percentage of iron and silica is eliminated by being broken free in crushing. Until methods for the recovery of fine ore were introduced a minimum of crushing was done, but modern methods allow more than formerly. The depression years brought about the need for increased recovery of ore handled on the part of the producers and a demand for a higher grade of product on the part of the buyers. Improvements in milling and mining practice have had a far greater effect, however, than merely the production of a better grade of ore with greater recovery. They have opened for mining large areas that a few years ago were considered noncommercial deposits because of their inaccessibility and their high iron content. It is no exaggeration to say that the new methods have more than doubled present known reserves of barite ore of economic value.

Jan 1, 1938

GENERAL GEOLOGICAL DESCRIPTION The uranium mineral appraisal herein described was made for an ore deposit in New Mexico. The uranium mineralization occurs as roughly tabular to lens-shaped deposits of varying thickness within the sandstone of the Jackpile formation of Jurassic age. The mineralization occurs at several horizons within the Jackpile formation, but is not always confined to specific beds. It often transgresses across stratigraphic layers, as demonstrated when attempting correlation of uranium gamma anomalies between adjacent drill holes. Preferred mineral trends have been established in some parts of the deposit, but are not always predictable when attempting to extrapolate beyond the zones defined by drill hole sampling. MANAGEMENT OF DRILL HOLE SAMPLE DATA All of the drill hole sample data used in the appraisal were obtained from interpretation of gamma-ray logs. A brief description of gamma-ray log sampling is given in Chapter 2. Two preliminary steps are involved in preparing gamma-ray logs into sample data normally acceptable for computer manipulation. 1) The gamma analog trace produced by the downhole probe must be digitized, i.e., counts-per-second (CPS) are recorded for each 0.15 m (1/2-ft) interval across the gamma-ray anomaly. The work is usually done on a "digitizer" while following the analog trace with an electronic stylus on a special tablet or table. The other alternative is to do the work manually. Some of the newest downhole logging equipment produces a magnetic tape output which can be read by a computer. 2) The gamma-ray CPS values must then be converted to equivalent U308 assay values, taking into consideration all appropriate correction factors. The US Atomic Energy Commission, now part of the Department of Energy, developed the theory and algorithm for this conversion in the 1960's, and though the work can be done manually, it is best done with the GAMRED (gamma-reduction) computer program. Fig. 14-1 illustrates a typical analog trace produced by the probe instrumentation, including gamma-ray trace (left), self-potential electric log (center), and resistivity log (right). Fig. 14-2 shows a form of the computer output after the analog data has been digitized to 0.15-m (1h-ft) intervals and converted to percentage U308 values for the same hole. The U308 grade bar graph on the right permits rapid visual inspection of anomalous values by depth and elevation. The converted U308 sample data were next processed by the SURVEY program that assigned to each assay interval [0. 15-m (1h-ft)] an X Y Z coordinate, taking into account all deviations indicated from downhole survey information. The output file of the SURVEY program was listed on the line printer for examination by project geologists, and also became the main input file for the URAN/ COMP compositing program, which is designed to group individual 0.15-m (/-ft) U308 sample values into larger intervals representing discrete anomalous zones according to a series of specified parameters entered into the program by the user. Composite U308 intervals were computed by the URAN/COMP computer program, the logic of which may be briefly described as follows: Step 1 The program searches for the highest U308 value in the hole and builds a composite by adding the highest grade interval on either side so long as the added value is greater than a minimum acceptable grade, and the total composite, after addition, meets minimum GT (grade times thickness) constraints. Step 2 The program loops back to find the next highest assay value in the hole not already included into a composite, until all anomalies above minimum cutoff grade are composited. Step 3 Individual composites are combined if they are closer than a specified minimum waste thickness, and the resultant composite grade still meets GT minimums.

Jan 1, 1980

By Hugh Henton

THIS paper is the result of an investigation made in association with Dr. Charles H. Fulton. Early in 1918 a search was started for methods of utilizing, in the manufacture of basic refractories, certain domestic resources in magnesites, dolomites, and magnesian limestones. Much information was collected during that year and during 1919 regarding magnesite and dolomite deposits. During 1920 and 1921 a research was made into methods of calcining dolomite and separating magnesia therefrom. Some success was attained and many new ideas were brought out in connection with the preparation and utilization of magnesia in the form of "caustic" or light-burned material as well as in the form of refractory or "dead-burned" material. Stimulated by this success, much advance has been made in manufacturing processes for the "plastic magnesia," so called, used for magnesia cement, stucco, flooring and otherwise in the structural industries.

Jan 3, 1926

By W. D. Lowry

As most of the industrial activity of Oregon is centered in the Portland area, the foundries there consume the bulk of the foundry sand produced in Oregon. Although a number of the larger towns scattered throughout the state have gray-iron foundries, the sand used by most of them is of local origin. The yearly consumption of foundry sand of all types for the past few war years in Oregon is estimated to have been approximately 40,000 tons valued at about $285,000, of which an estimated 18,000 tons was shipped in from the Ottawa, Ill., district for use largely by the steel foundries. Until 1945 much of the silica sand consumed by the steel foundries in the Pacific Northwest, approximately 50,000 tons in 1944, came from Ottawa, Ill. and surrounding regions. Although some silica sand was shipped in from Belgium in the past, none is known to have been imported in recent years. Early in 1945, a very promising high-grade silica sand being produced near Eugene, Oregon, was introduced, and all but two of the Portland steel foundries are using this new sand. Until a few years ago, the search for good local (Oregon) foundry sands was carried on largely by the foundry supply houses. Recently the Oregon Department of Geology and Mineral Industries has investigated a number of deposits and has carried on and fostered research on the most bromising deposit near Eugene, about 120 miles south of Portland. High-grade silica foundry sand from this deposit is now being marketed in Oregon, Washington, and British Columbia. The Eugene sand is one of the very few outstanding western steel-foundry sands. Field investigations by the Oregon Department show that there are relatively few deposits of sand in Oregon suitable for foundry use. A knowledge of the geology of the state makes this readily understandable. The only major primary sources of the quartz present in sandstones in Oregon are the intrusive masses of granite, granodiorite, and quartz diorite of late Jurassic or early Cretaceous age found in the Siskiyou Mountains of southwestern Oregon, a part of the old Klamath Mountain highland, and in the Blue Mountains of northeastern Oregon. Transportation militates against the development of any possible deposits of foundry sand found east of the Cascade Mountains in central and eastern Oregon because few railroads traverse that area. East of the Cascades, which separate western from eastern Oregon, many of the older sediments of Paleozoic and Mesozoic age have either been metamorphosed or contain much volcanic eruptive material, and even if some of the Mesozoic sediments are highly quartzose in places, they are in relatively inaccessible areas. All the Tertiary sediments there are of continental origin and contain much ash and other volcanic debris, for there was great volcanic activity during much of that period. In western Oregon much the same is true of the Paleozoic and Mesozoic rocks

Jan 1, 1948

By W. D. Lowry

As most of the industrial activity of Oregon is centered in the Portland area, the foundries there consume the bulk of the foundry sand produced in Oregon. Although a number of the larger towns scattered throughout the state have gray-iron foundries, the sand used by most of them is of local origin. The yearly consumption of foundry sand of all types for the past few war years in Oregon is estimated to have been approximately 40,000 tons valued at about $285,000, of which an estimated 18,000 tons was shipped in from the Ottawa, Ill., district for use largely by the steel foundries. Until 1945 much of the silica sand consumed by the steel foundries in the Pacific Northwest, approximately 50,000 tons in 1944, came from Ottawa, Ill. and surrounding regions. Although some silica sand was shipped in from Belgium in the past, none is known to have been imported in recent years. Early in 1945, a very promising high-grade silica sand being produced near Eugene, Oregon, was introduced, and all but two of the Portland steel foundries are using this new sand. Until a few years ago, the search for good local (Oregon) foundry sands was carried on largely by the foundry supply houses. Recently the Oregon Department of Geology and Mineral Industries has investigated a number of deposits and has carried on and fostered research on the most bromising deposit near Eugene, about 120 miles south of Portland. High-grade silica foundry sand from this deposit is now being marketed in Oregon, Washington, and British Columbia. The Eugene sand is one of the very few outstanding western steel-foundry sands. Field investigations by the Oregon Department show that there are relatively few deposits of sand in Oregon suitable for foundry use. A knowledge of the geology of the state makes this readily understandable. The only major primary sources of the quartz present in sandstones in Oregon are the intrusive masses of granite, granodiorite, and quartz diorite of late Jurassic or early Cretaceous age found in the Siskiyou Mountains of southwestern Oregon, a part of the old Klamath Mountain highland, and in the Blue Mountains of northeastern Oregon. Transportation militates against the development of any possible deposits of foundry sand found east of the Cascade Mountains in central and eastern Oregon because few railroads traverse that area. East of the Cascades, which separate western from eastern Oregon, many of the older sediments of Paleozoic and Mesozoic age have either been metamorphosed or contain much volcanic eruptive material, and even if some of the Mesozoic sediments are highly quartzose in places, they are in relatively inaccessible areas. All the Tertiary sediments there are of continental origin and contain much ash and other volcanic debris, for there was great volcanic activity during much of that period. In western Oregon much the same is true of the Paleozoic and Mesozoic rocks

Jan 1, 1948

By J. J. Arps

This paper is a study of the effect of temperature on the electrical resistivity of sodium chloride solutions based on the published resistivity and density data in the International Critical Tables. This temperature effect is of considerable importance in quantitative interpretation of electric logs, where it is frequently necessary to correct mud resistivities measured under surface conditions to temperatures existing at the bottom of the bore hole. An empirical approximation formula was developed for this conversion which has proved to be very useful and seems to provide results well within the range of accuracy of the data involved. This approximation formula states: sistivities of sodium chloride solutions at temperatures of t and t degrees Fahrenheit, respectively. INTRODUCTION Research by various investigators during the past 20 years has clarified the physical principles of the phenomena which cause the natural or spontaneous electric potential in rotary drilled bore holes. The basic relationship which is most commonly used reads: in which the SP deflection, as measured from the shale base line, is expressed in millivolts. K is a constant, which appears to vary between 50 and 110; the low value applying to shaly sands, whereas the higher values are more common in carbonate rocks. A good average value for K = 70. for which value there is considerable theoretical justification." In order to calculate the resistivity of the connate water R and to estimate its "equivalent salinity" (as NaCl) from an electric log by means of this SP relationship from a knowledge of the static self potential and of the resistiv- ity of the mud filtrate R it is necessary to first correct the resistivity of the mud filtrate measured under surface conditions to the resistivity of this same mud filtrate in the well bore at a different temperature. In order to make this temperature conversion for the mud filtrate the variation of the electrical resistivity of sodium chloride solutions with temperature is commonly used. Since some discrepancies were found in the charts ordinarily used for this purpose, it was felt desirable to make a new study of this relationship based on the published measurement data. Because of the fundamental nature of these relationships and as an aid to other workers in this field, an attempt has been made in this study to show every step in the calculations. CONDUCTIVITY VS MOL CONCENTRATION The most complete published reference on the temperature relationship of sodium chloride solutions of different concentrations is provided in the International Critical Tables.' The basic measurement data on the electrical conductivity of aqueous sodium chloride solutions, at different temperatures, as given in these tables, are reproduced in Table 1. The electrical conductivity values in this Table 1 are expressed as 10' times the specific conductivity k in ohm-'cm'l per unit of concentration in milligram mols per liter of solution C, or: RESISTIVITY VS MOL CONCENTRATION These conductivity values from Table 1 were first converted to the corresponding electrical resistivity values (R) , expressed in ohm-meters, as is conven-

Jan 1, 1953