Search Documents

By G. F. Bolling

Single crystals of each metal were deformed at 77°K and heated at constant rates, variously in the range 0.125" to 4o°Kper min from 77" to -390oK, while being monitored in an X-ray diffractometer. Changes in diffraction-peak heights and line breadths were used to ascertain the temperature ranges of recrystalliza-tion. The results were subjected to the analysis of nicholas' in order to obtain the rate-controlling activation energies,Q. In this analysis no recourse to a separate and distinct nucleation stage is required and the results of studying recrystallization proved consistent with the hypothesis of a constant number of nuclei or equivalent hypotheses. The values Pb = 5.5 ± 0.5 keal per mole Zn ~ 7.5 Sn - 5 Bi - 9. 5 correspond for lead, zinc, and tin to activation energies obtained elsewhere for grain boundary migration, and for bismuth and lead to previous studies of re-crystallization by Barrett.6 This correlation allows the conclusions that interference from recovery was minimal and that the observed recrystallization rates in these pure metals are effectively governed by grain boundary migration. Good agreement was not found between the results of this kind of study in zone-refined aluminum and previous work; and supplementary isothermral experiments involving hardness tests and metallography did not resolve the discrepancy. Nevertheless, at least a range,Q = 11.5 ± 2 keal per mole, can be assigned to the activation energy for boundary migration in aluminum. An experimental study of one aspect of the recrystallization process is presented here for four metals of different crystal structure. The metals chosen for study were all zone-refined to reduce impurity effects, but the attendant high purity presented a difficulty. For any reasonably high driving force a "re-crystallization temperature", TR, is in the range of 0.25 T,, where T, is the absolute melting point, and study was therefore restricted to lower temperatures. An X-ray technique under constant heating-rate conditions adequate above 90°K was devised for the study; in consequence, a newer type of analysis following Nicholas1 had to be used to obtain quantitative information about activation energies. The standard methods of studying recrystallization have involved the comparable analyses of Johnson and Mehl2 and Avrami3 which are reviewed by Burke and Turnbull.* The general analysis4 which is applied only to isothermal studies using any of various investigative techniques states:

Jan 1, 1968

By George F. Comstock

It has been known for many years that the alloy containing 90 per cent. copper and 10 per cent. aluminum can be hardened, like steel, by quenching from a suitable temperature, and that the hardened alloy can be softened again by annealing or drawing the temper. It does not seem to be generally appreciated, however, that the effect of the first slight reheating after quenching is actually increased hardness, the softening effect not taking place until a certain temperature of "drawing" has been exceeded. This paper gives the results of a few experiments on various specimens of cast 10 per cent. aluminum bronze, quenched for maximum hardness, and subsequcntly annealed at different temperatures. The hardness measurements were made with both a scleroscope and a standard Swedish Brinell machine; some peculiarities of the scleroscope test on this material are described. The author is not aware of many previous investigations of the hardness of this alloy when quenched and drawn, but two important papers on the subject should be mentioned. The earliest was by Portevin and Arnou,1 in which it was stated that tempering quenched 10 per cent. aluminum bronze at 400" C. increased the hardness as compared with the quenched untempered alloy and that reheating above that temperature ' was necessary to obtain any softening effect. A later paper was by Seidell and Horvitz,2 who mentioned Portevin and Arnou's work, but did not report any increase in hardness obtained

Jan 1, 1925

By Frances Hurd, Clark

Iv 1897, Roberts-Austen(l)$ found an arrest in the thermal curves of alloys of 60 per cent. copper and 40 per cent. zinc. This break occurred from 450° to 470° C. Shepherd, (2) working in 1904, was unable to detect any change in the direction of the thermal curve. In 1911, Carpenter and Edwards(3) confirmed the work of Roberts-Austen and called this a eutectoid transformation of beta to alpha plus gamma. Hudson') in 1914, showed that the beta constituent could be produced synthetically at temperatures below the transformation point. He believed the change in the beta was polymorphic in nature rather than a eutectoid. The work of Matsuda(32) in 1922 demonstrated this break by thermal analysis, microscopic investigations, dilatation, electrical resistance measurements, and a thermoelectric study. He believed the transformation to be continuous from 300° to 480° C., and comparable to the A 2 transformation in iron. Later, in 1924, Andrew and Hay, with electrical resistance measurements, confirmed Matsuda's work. Imai(28) showed the transformation to be progressive and therefore a function of the temperature rather than the time. He stated that it was neither a eutectoid nor an allotropic change of phase. Atomistically expressed, it was a change, not of atomic configuration, but of atomic energy of some kind; and again it was compared to the A 2 transformation in iron. Imai believed that his analyses by X-rays led to the same conclusion. In order to study this change, at 470'C., in homogeneous 60:40 brass, Homerberg and Williams «0> and Homerberg and Shaw(41) quenched their material in iced brine to obtain the beta solid solution and reheated at various temperatures. At 200° C., a change in the microstructure and physical properties occurred. A fine-grained structure, which they termed alpha and which had the appearance of a sorbitic steel, appeared, with an increase in the tensile strength to 82,750 lb. per sq. in., and a Brinell ball hardness of 240 with 3000 kg. load. At 470° C., the alpha

Jan 1, 1927

By W. C. Lilliendahl, H. W. Highriter

THE method developed and used in this laboratory for the production of metallic uranium of such purity that it is ductile and can be cold-worked to fine wire or thin sheet by rolling has already been described1. It consists, briefly, in the electrolysis of potassium uranous fluoride (KUF6) in a molten bath composed of equal parts of sodium and calcium chlorides. The bath is contained in a graphite crucible, electrically heated to about 775° C., the crucible serving as the anode for electrolysis. The uranium deposits in finely divided form mixed with salts upon a molybdenum cathode suspended axially in the crucible. Upon completion of the electrolysis the cathode is removed and cooled, the deposit broken and leached to remove salts. The metal powder is washed with water and dilute acetic acid and dried in vacuo to reduce oxidation. Suitable amounts are then pressed into pellets and heated in vacuo by high-frequency induction, using a thoria crucible. The uranium melts and flows away from the pellet, leaving a shell, which is largely oxide. In general, this method produced a satisfactory metal, although at times the uranium was not ductile. The investigations recorded here were made to find the cause of this embrittlement. It was known that the metal generally contained carbon, derived from disintegration of the graphite crucible in which electrolysis is conducted, in amounts dependent upon the thoroughness of washing the metal powder. Accordingly, analyses of several samples, both ductile and brittle, were made by combustion and absorption of CO2 in Ascarite, using air instead of oxygen to reduce the temperature and rate of oxidation. Several of these metals were made with special precautions to reduce carbon content. The results show no relationship between ductility and carbon content in the range investigated (Table 1).

Jan 1, 1935

By F. L. Wolf, G. E. Alderson

The reclaiming of nietallics from slag and sweepings is of vital interest to every brass-foundry man, but the first cost and interest on the investment often make it prohibitive for the small foundry to enjoy the benefits of a complete concentrating unit. However, the cost of such an installation and the cost of operation are often exaggerated to such an extent that foundries dispose of their copper-bearing refuse at a great loss. This paper gives the actual costs and the returns obtained in the reclaiming plant used at the Ohio Brass Co. This plant is divided into two sections—the preliminary treatment and concentrating departments. In the former occur the screening, crushing, and hand-picking operations whereby rnost of the non-valuable and heavy metallic constituents are removed. The concentrating equipment consists of an elevator, bins, jigs, ball-mill, arid table. Preliminary Treatment The preliminary treatment varies, depending on whether the material is slag, foundry-floor sweepings, or brass casting-floor sweepings. Material of the first class is produced from the operation of six Steele-Harvey and six Schwartz furnaces; the second class represents sweepings from an average of thirty-five. molding floors per day: and the last is collected around the sprue cutters and knockout bench. Treatment of Slag The slag, analyzing 30 to 40 per cent. copper, is passed over a 3-mesh yard screen (Tyler standard mesh) stretched on an inclined rectangular frame supported by adjustable legs and equipped with a hopper which directs the undersize into a barrow. The fine product, running about 20 per cent. copper and representing 20 to 25 per cent. of the total slag, goes direct to a storage bin for concentrator frrd. The oversize is charged into a No. 2 Hill cinder crusher, which takes 175 to 200 11,. to a charge and crushes two charges per hour through 'a No. 4 riddle. It

Jan 1, 1921

By Douglas A. Sloan

Who would believe that young elementary school children could understand something as complex as the mining industry? The Challenge The challenge of accomplishing this is tremendous. An examination of Canadian school children indicated that they knew very little about the world of work in general, and hardly anything about the mineral resource industry in particular. It calls to mind the story about two youngsters who decided to play house. The little girl played her role well as she went about the house doing things she had watched her mother do every day. When it was the little boy's turn, he grabbed his lunch, waved goodbye to his "wife," jumped on his bicycle and pedalled furiously down to the end of the driveway-where he stopped. The youngster explained that he saw his dad go out of the driveway each morning, but he didn't know where he went, or what he did on the job. When you stop to consider the number of families today with two working parents, you can begin to appreciate the importance of the opportunities for role identity provided by this project. The Approach The challenge of teaching the school children of Canada about the world of work and, specifically, the mining industry is the challenge which the Canadian Institute of Mining and Metallurgy met with the Curriculum Development Research project. It started when a small, dedicated group of Vancouver members met Dr. Doreen Binnington. After this meeting, Dr. Binnington, an expert in curriculum development at the University of British Columbia, set herself to develop a curriculum program for the elementary shcools which accomplishes two main goals: It uses the "Identity Approach," developed by Dr. Binnington, an expert in curriculum development at the enable students to understand and appreciate the contribution of people, in this case, working with mineral resources. It has pupils enthusiastically exploring the importance of rocks, minerals, and the mining industry in their lives [(Fig. 1)]. Evolution of the Curriculum Development Research Project When the curriculum development research project was presented to the Vancouver Branch of the Canadian Institute of

Jan 1, 1981

By Eugene A. Stephenson

The writer apologizes for presenting this very elementary analysis of one aspect of proration, but a search of the literature failed to disclose any concrete illustrations of the effect of various proration formulas upon the allowable oil produced by tracts of different sizes. Many engineers have doubtless made somewhat similar calculations and are fully acquainted with the results. The various allocation formulas that are in use are based on one or more of the following factors: (1) wide-open well potential, (2) potential through an orifice, (3) uniform well allowable, (4) acreage, (5) sand thickness, (6) bottom-hole pressure, (7) productivity index, and (8) volumetric displacement. Of these, the unrestricted potential formula, or open-flow test, and the uniform well allowable are commonly regarded by engineers as those least likely to give each producer his proportionate share of the oil or gas, as represented either by acreage or by sand thickness, or both, except when the wells are located on tracts of large size. Unless the mechanical equipment that may be used during the potential test and the method of taking the test are both specified, the net result of the potential formula is to practically force the operators to use special equipment and adopt special procedures prior to and during the potential test, so as to secure the largest possible allowables. Much ingenuity and skill have been devoted to this,problem, but the general effect is to permit excessive allowables for very small tracts, and stimulate unnecessary drilling. It is interesting to compare some of the high yields from the Wilcox horizon at Oklahoma City with each other, as an illustration of the effect of an allocation factor based solely on potential (Table 5). One of the glaring instances is a well on a ½-acre lease, which had produced, as of September 1936, at the rate of almost 3,000,000 bbl. per acre. This is at least twice as many barrels as could have been present under the property if the reservoir had consisted of a tank of oil 200 ft, deep and 56 acre in area. Numerous combinations of acreage, potential, bottom-hole pressure, sand thickness, etc., have been proposed and are in use in various fields.

Jan 1, 1937

By Wallace Ralston

The East Texas area includes the northeast 38 counties of the state of Texas. It covers all, and extends beyond, the borders of what is commonly described as the East Texas Basin. It is one of the most important oil and gas-producing areas of the Mid-Continent Province. It includes four important oil fields—Van, East Texas, Cayuga and Long Lake— and the recent extension of Rodessa field into Cass County, Texas, may prove to be of major size. Four commercial gas fields are in this area— Bethany, Waskom, Cayuga and Long Lake. Up to January, 1936, all of the oil has been produced from the Upper Cretaceous formations, and most of that from the basal member, the Woodbine sand. Gas is produced from both the Upper and Lower Cretaceous formations. Development in Fields East Texas Field.—This field continued to dominate the drilling and production situation throughout the United States. There were 4036 wells completed in this field during 1935; that is, 365 more wells than were completed during 1934. Drilling activity was due to close spacing of wells and the addition of 10,000 acres to the field. The field is now drilled to a density of one well to 6½ acres, which is certainly more wells than necessary for economic production of the field. The close spacing of wells is due mostly to the type of proration, which is per well allowable based on a potential test, and does not take acreage into consideration, and also to the numerous small acreage tracts such as town lots and excess strips. The field now has 19,519 producing wells. The allowable production for the field during 1935 was 161,118,659 bbl.; estimated production, including illegal or "hot oil," was 174,200,150. The illegal production of oil gradually decreased throughout the year, until an estimated low was reached of 20,500 bbl. daily during the months of November and December. The price of oil remained at $1.00 per barrel throughout the year. As stated, about 10,000 acres were added to the field during the year, making a total of 128,000 productive acres. There is a possibility that

Jan 1, 1936

By Roscoe C. Clark

In a previous technical note' by Walter Rose, evidence is offered in support of the contention that "the possibility of describing oil recovery features in terms of capillary pressure phenomena has not been established entirely." It is not the purpose of this note to present further discussion of this possibility but rather to point out that the argument presented there does not appear to be generally valid. In the cited note' reference is made to the experiments of Welge2 wherein it was shown that when water was displaced by oil from a core the pressure in the water phase was less than in the oil phase but that when this oil was then produced by water drive the pressure in the water phase was greater than in the oil phase. Rose has concluded from these observations that conditions of static equilibrium did not obtain since the fluid saturations were such that phase discontinuities seemed unlikely. The argument from which this conclusion was drawn is based on the contention that "the pressure is always greatest in the non-wetting phase at each static interstitial interface of contact with the wetting phase." This premise appears to have been reached from a consideration of capillary phenomena in cylindrical tubes, although it may a1so hold for other types of pore geometry, hut as will be shown below it does not hold for all pore shapes and hence is not generally applicable. Since the pore structure of porous media such as reservoir rocks i- in general so complex as to defy exact description. it is undoubtedly of great value to establish a model in terms of pore shapes of known geometry, provided of course that the limitations of the model are recognized. That the limitations of the capillary. or cylindrical, tube model have not always been fully recognized will be evident from the following discussion of a pore of different shape hut one which may a. logically he considered a.; the capillary tube. The pore space to be considered is that shown in Fig. 1, which may be thought of as the "hole in a doughnut."* Consider the interface, A-B-A', between two immiscible fluids, P, and P2, which interface meets the solid alone a line, A-C.A'-C'. The interface A-B-A' is the surface of a spherical segmen† while the line of mutual contact be-

Jan 1, 1950

By Arthur F. Taggart

In 1900, Elmore found that if an acidulated pulp was stirred up with an oil which was relatively insoluble in and lighter than water, and the mixture was allowed to stratify, much of the sulfide would be found hanging to the lower surface of the floating body of oil and could be skimmed off or overflowed with it. The action of the flotation agent here is twofold, first to select the sulfide from the gangue—what today is called collection—and second, to buoy the collected sulfide away from the gangue. The action in collecting is illustrated by Fig. 1: which contrasts the behavior of drops of oil brought, under water, to the surfaces of gangue and sulfide particles, respectively. The oil displaces water from the surface of the sulfide; the water displaces oil from the gangue surface. If, instead of considering the solid particles the fixed parts of the system of oil, water and solids. we consider the oil and water fixed and the solids presented to the surface of contact, the condition will be as shown in Fig. 2; the sulfide tends to be drawn into the interface and the gangue to be excluded. The sulfide particles are held in the oil-water surface by the tension of this surface. The buoyant effect is supplied by the oil droplets in bringing the sulfides to the water surface, but not in holding them there. Gas as Buoyant Medium of Flotation In 1906 Sulman. Picard and Ballot discovered a practical and substantially fool-proof method of doing what Everson, in 1886, and Fro-nlcnt. DeBavay Bessel and Elmore had been doing in the intervening years, viz.: using gas in place of oil as the buoyant medium for flotation, but retaining oil as the agent. To all of these inventors "oil," with no qualification as to its kind and no true understanding of its function, was the important thing. Hut they placed on the oil an additional burden viz.: froth-making, and it soon became apparent that not all oils were suitable for the dual purpose. As a matter of fact, it is probable that each of these inventors knew only one suitable oil at the time he wrote his patent, but used the generic term in the patent with the usual idea

Jan 1, 1928

By L. W. Page

PREVIOUS to the introduction of the motor vehicle the broken stone or macadam road met the conditions of rural horse-drawn traffic better than any other type of road, but under fast motor traffic it has been proved to be quite unsatisfactory, and necessitates high maintenance charges. Such a road depends for its success upon the fact that the rock dust fills the voids between the stones and acts as a cement or binder. Under ideal conditions it should be constructed of rock so suited to the volume and character of horse traffic that only enough fine dust is worn from the stones of which the road is composed to take the place of that carried off by wind and rain; and when these conditions are met, the fine dust resulting from the wear. of traffic forms with the stone a smooth, impervious shell, shedding the surface water and protecting the foundation. With increase in the number and speed of motor vehicles, however, it was soon found that the cost of maintenance also increased, until at the present day highway engineers consider the old method of constructing and maintaining broken-stone roads increasingly inadequate, and are introducing every known type of binding material other than rock dust to cement the stone together. Among the most prominent types of products in use are those produced from our various petroleums. That the value of modern methods of road preservation was appre¬ciated in this country much earlier than we have been accustomed to believe is demonstrated by the recent revival of an old patent which was granted to one John Martineau, of Elbridge, N. Y., in 1834. Petroleum had, of course, not been discovered at that time, but he claims as his invention and improvement "The application of tar, turpentine, or any of that class of tenacious, cohesive substances, reduced before use to a fluid state, and that state used as a cement, to apply to, and combine with sand, gravel, pebbles, and pulverized stone, such as is used for a Mc-Adam road, or cobble stone, the interstices of coarser material being in all cases filled, as well as may be, with sand and gravel and cemented with tar or turpentine, to form the wearing face or surface of streets,

Jan 2, 1914

By W. H. Class

The embrittling effects of oxygen, ozone, nitrogen, air, and surface residues, on NaCl has been investigated. The embrittlement by ozone and oxygen was found to be associated with the formation of a NaClO3 surface compound. In these cases the initial crack that was responsible for fracture (in a bend test) always nucleated at the corners between the tension and side faces. The behavior of air was very erratic and on certain days did not produce enzbrittlement. During these periods, crystals that had become embrittled by the ozone treatment completely recovered their ductility after a short exposure to the ambient atmosphere, It was established many years ago1 that considerable ductility could be obtained in NaCl single-crystal specimens if the crystal surfaces were dissolved in water either during or immediately prior to the test. The original interpretation of this effect by Joffe attributed the enhanced ductility to the removal of surface microcracks by dissolution. Later investigations2'3 have suggested that the exclusion of air from the specimen surface is the criterion for extensive plastic flow prior to fracture. The air em-brittlement in this later work was attributed to the diffusion of gaseous atoms into the surface layers of the crystal, thereby impeding the movement of dislocations. This model satisfactorily accounts for the reembrittlement observed after further air exposure subsequent to the water dissolution treatment. However, the situation has recently become more complex by the observations in several laboratories4-t that under certain conditions air exposure does not impair the ductility of NaC1. It has also been recognized5 that improper drying operations after water dissolution can leave surface precipitates that lead to embrittlement. Cleavage defects on as-cleaved crystals can often be another source of embrittlement. In the present work the effect of the gaseous atmospheres nitrogen, argon, air, oxygen, and ozone, on the ductility of rock salt was studied extensively. The embrittlement resulting from oxygen and ozone exposures was found to be associated with the formation of a NaC1O3 surface film. It is suggested that certain atmospheres, one of which often can be ambient air, which inhibit the formation or favor the decomposition of this compound, can promote ductility. Thus one aspect of the Joffe effect is certainly related to the removal of surface compounds or complexes by water dissolution. The effect of surface precipitates that remain after drying operations and of cleavage defects were also studied. In neither of the latter cases was the embrittlement as severe as that found with a NaClO3 surface layer. PROCEDURE AND SPECIMEN PREPARATION The nature of the embrittlement produced by the agents mentioned above was studied by means of microscopy, mechanical testing, and X-ray diffraction. Specimens were cleaved from large crystals of optical quality sodium chloride obtained from the Harshaw Chemical Co., and, except for those tested in the as-cleaved condition, were given a 15- to 20-sec immersion in distilled water followed by a rinse in absolute methyl alcohol. The specimens were then blotted on a soft, absorbent paper, and dried by a few seconds exposure to a stream of warm, dry air. Such a procedure was found to give a control surface which was microscopically free of residues. (A few crystals were intentionally painted with a concentrated NaCl solution in order to investigate the effect of surface residues). All specimens were of 0.140 sq in. cross-section. Crystals prepared in the above manner were immediately placed in a gas train where they could be exposed to the desired gases for preselected periods of time. For the oxygen and nitrogen exposures, pure reagent-grade gases were employed. The ozone was provided in the form of an ozone-oxygen mixture (approximately 10 pct ozone) prepared by passing commercial grade oxygen over a strong ultraviolet light source. All gases were dried prior to their introduction into the train. Since argon was found to be completely inert in its behavior (i.e., residue-free specimens that were exposed to argon were not embrittled), it was periodically utilized to check the control specimen surfaces as well as the condition of the gas train used for aging the specimens. After exposure to the gaseous media in question, the crystals to be used for the measurement of the strain to fracture were transferred from the gas train to a protective oil bath (without further exposure to the atmosphere) where the tests were conducted in three-point bending. The apparatus was so adjusted that the load could be applied at a constant, continuous rate. Other Snecimens from the gas train were deformed

Jan 1, 1962

By C. N. J. Wagner, E. N. Aqua

The bee alloys of the terminal solid solution of rhenium in niobium were investigated by X-ray diffraclion methods. The analysis of the broadening of the powder pattern peaks from the niobium-rich alloys, cold-worked by filing, showed evidence for faulting on (211) planes. The alloys with larger rhenium concentrations were brittle, and fractured when filed. The analysis of the shapes of the diffraction profiles from powders produced by hammering with steel plates) of these brittle alloys indicated that the broadening was due predominantly to platelets bounded by clibe planes. This result was consistent with the Laue patterns from single-cleazlage facets which showed evidence for clearage fracture on {100} planes. The influence of faulting on the mechanical properties of face-centered cubic (fcc) metals and alloys, i.e., how faulting affects the various dislocation configurations in fcc metals, is well-known.' The important question is whether or not faulting occurs in body-centered cubic (bcc) metals and alloys, and, furthermore, if faulting does occur, to what extent it affects the mechanical properties. Theoretical calculations indicate that the stacking-fault energy is rather high in most bcc metals.2 The results of sev-eral studies using transmission electron microscopy have indicated that faults are present in well-annealed and lightly deformed bcc metals and alloys, such as tungsten,3 vanadium,4 and Mo-Re alloys.5,6 These faults, as have been observed, may be stabilized by the presence of interstitial (C,N,O) atom segregation to the extended dislocations. In addition, there is considerable X-ray diffraction evidence for faulting in bee metals,7-8 using the same techniques that were successful for the study of faulting in fee metals and alloys.7 This X-ray diffraction method is currently the only technique applicable for the investigation of faulting in metals with high stacking fault energies, i.e., when severe amounts of deformation are required to produce sufficient amounts of faulting to be detectable by X-rays. The thinned films of heavily deformed metals will become opaque in the electron microscope due to the high dislocation densities present. In a previous investigation of faulting8 in bee metals of group Vb and VIb, the authors observed that niobium was ductile when filed at room temperature, and showed the highest density of faults on the (112) family of planes. A niobium-base alloy system was therefore chosen to study the effect of alloying on the occurrence of faults in a bcc alloy. There is a large range of terminal solid solubility of rhenium in the alloys of the bee refractory metals. All of the Group VIb-rhenium alloys, i.e., Cr-Re, Mo-Re, and W-Re, exhibit solid solution hardening without loss of ductility.9 In fact, the ductility reaches a maximum for alloys with compositions near to the limits of solubility. This enhanced ductility has been attributed to the lowering of the stacking-fault energy in the alloy; i.e., the increased amounts of twinning provide an additional mode of deformation, resulting in the observed high ductility.' Because of this demonstrated effect of rhenium in bee alloys, it was decided to study a series of alloys of Nb-Re. Using the same X-ray diffraction methods as described in the previous investigation,' one is able to identify the possible causes of broadening of the powder pattern peaks, e.q., particle size, microstrains, stacking faults, and/or twin faults. The separation of these various contributions to the measured peak shape is accomplished by the Warren-Averbach analysis.7 I) EXPERIMENTAL PROCEDURE A series of seven bee solid solution alloys containing from 2.5 to 21.5 at. pct Re (remainder niobium) were prepared at the General Electric Research Laboratory. Buttons, weighing 25 g, were alloyed from electron-beam-melted niobium chips and random rhenium sheet by arc melting in a water-cooled copper crucible, under an argon atmosphere. The buttons were inverted and completely remelted to promote homogenization. The nominal alloy compositions are listed in Table I. Samples of the cold-worked alloys were obtained by filing to produce a powder for the X-ray study. Alloys too brittle to be filed were hammered with steel plates. The resultant filings or brittle impactings were screened through 150-mesh classifiers and compacted to the required shape for the diffractometer holder. The X-ray diffraction peaks were automatically recorded by fixed time counting at uniform 28 intervals, or by continuous registration with a ratemeter. In all cases, the (110)-(220) and (200)-(400) pairs of peaks and the (211), (310), (222), and (321) reflections were measured on a GE-XRD5 diffractometer using CuKa radiation with nickel filter or MoKct radiation and a LiF monochromator in the diffracted beam. The first part of the data reduction, completed with the aid of a series of programmed computations,10 was the analytical resolution of the Kol component of the diffraction profile. Subsequent computations were then made with reference only to the resolved Kol peak shape. These included the measurement of the

Jan 1, 1967

By Frank F. Aplan

In looking into the crystal-ball scene of minerals beneficiation for 1970 and beyond, an impartial observer becomes con- fused as to what has been done and what is possible in the way of improvements. The mining official must balance the burden which is being shouldered by the mineral industry for maintaining our environment in its pristine state on one hand, with the solid advancements made in technology and cost savings on the other hand. Then the official wonders if this is really the criterion for judging overall performance today. As a prospective engineer, Dave Bolles sees it this way: "Specialization has caused many engineers to subordinate everything to doing their job the cheapest and fastest way. In the future this won't be enough. The engineer in the mineral industry will be responsible not only for mining, concentrating and smelting, but also for the resultant wastes- the mine dumps, the tailing dams and the slag piles." (See Drift on page 63).

Jan 1, 1971

By George D. Graffin.

The first use of graphite is lost in the mists of time. It was used by primitive man to make drawings on the walls of caves and by the Egyptians to decorate pottery. As early as 1400 A.D. graphite crucibles were being made in the Haffnerzell district of Bavaria. Through the Middle Ages graphite was confused with other minerals, especially galena and molybdenite. Two common names that are still used for the mineral are "Plumbago," meaning leadlike, and "Black Lead." The latter name implied that graphite is either composed of lead or at least contains a large percentage of it. Gessner is credited with having recognized it as a separate mineral in 1565, but its composition was not determined until 1779, when Scheele demonstrated that graphite oxidized to carbon dioxide, thus proving its carbon constitution. In 1789, Werner named it "graphite" from the Greek word "graphein," meaning to write. The United States has long relied on foreign countries for its graphite supplies. This reliance has been due more to the lack of suitable domestic graphites than to any particular preference for buying minerals overseas. Ceylon (now Sri Lanka) graphites were imported as early as 1820, and Madagascar graphites have been imported since the properties on that island were opened up about a hundred years later. Mexico has long supplied the United States with most of its requirements for amorphous graphite. Physical Properties and Classification Graphite is found in laminated, flaky aggregates disseminated in schistose rocks. It also occurs in veins and exhibits a foliated or fibrous structure. Graphite is a black lustrous mineral that crystallizes in the hexagonal system, with rhombohedral symmetry. The crystals have tabular form and are six-sided; the faces are commonly striated. The flakes have perfect basal cleavage and are opaque. When well crystallized, the flakes have a black metallic luster while the amorphous material is black and earthy, with a microcrystalline compactness. The flakes feel greasy. Graphite is an excellent conductor of heat and electricity. It melts at approximately 3550°C at a triple point under 1250 psi. It sublimes between 3300-3500°C at 14.7 psi. At 3726°C a second triple point occurs at approximately 100,000 atmospheres. Thermal oxidation in the presence of oxygen begins at 300°C and the rate increases with temperature. The three forms of carbon (charcoal, graphite, and diamond) are distinguished by chemical and physical tests. The specific gravity of charcoal is 1.3 to 1.9, of graphite 2.266 g/ cm3 (crystal density), and of diamond 3.5. Graphite has a hardness of 1 to 2 (Mohs' scale). Natural graphite can be divided into three classes: disseminated flake, crystalline vein (fibrous or columnar), and amorphous. Flake graphite is a lamellar form found in metamorphic rocks, such as marble, gneiss, and schist. Each flake is separate, having crystallized as such in the rock. Crystalline vein graphite is found in the form of well defined veins or as pocket accumulations along the intrusive contacts of pegmatites with limestones. The graphite of such deposits is of two types, foliated and columnar. The important Sri Lanka (Ceylon) deposits are vein type. Amorphous graphite is commonly found as minute microcrystalline particles more or less uniformly distributed in feebly metamorphic rocks, such as slates and shales, or in beds consisting practically entirely of graphite. The latter usually are metamorphosed coal seams and carry as much as 80-85% graphitic carbon, while the former, being altered carbonaceous sediments, commonly range from 25 to 60%

Jan 1, 1983

By S. J. Prison, C. R. Smith

The effect of fluid injection to control water coning in oil and gas wells was investigated. Analytical and model techniques were employed. The factors investigated were the position and length of the completion interval, the point of fluid injection, the viscosity of the injected fluid and the relative thickness of the oil and water sections. The resulting influence of these factors on the net producing water-oil ratio was determined. Several important conclusions can be drawn from the study. In general, it was found that the net producing water-oil ratio can be reduced by fluid injection. The magnitude of this reduction depended on the factors listed above. An important practical consideration is that the injection fluid may be either oil or water. If the injected fluid is less dense than the connate water of the reservoir, the fluid will not be lost. This fact is reassuring when valuable oil is being injected. Efforts to suppress water production were more successful when the injection fluid was more viscous than the reservoir oil, or when a zone of reduced permeability existed in the vicinity of the point of fluid injection. Under test conditions, little benefit was derived through the use of impermeable barriers or cement "pancakes". INTRODUCTION The occurrence of water coning has been known for at least 60 years. In thin oil or gas pay sections, the presence of an oil-water or gas-water contact hinders production and often causes early abandonment of the afflicted well if a completion is even attempted. Even when relatively thick pay sections are found, the encroachment of water when a water drive is present will eventually pose serious water coning problems. This water is often corrosive, expensive to separate from the oil or gas and is costly to dispose of. The theory of water coning has been discussed by a number of authors. 1,2,3,4 Briefly, water coning to the producing interval in a well is due to pressure gradients resulting from the production of fluid from the reservoir. These pressure gradients will cause a water cone to rise toward the bottom of the producing interval if a water-oil or water-gas contact exists. The tendency of the water to cone is offset or partially offset by gravity forces since the water has a higher specific gravity than the oil. A balance then exists between two forces, gravitational forces arising from the difference in specific gravities of the oil and water, and the pressure gradients causing the flow of fluids to the wellbore. If the pressure gradient exceeds the gravitational force, water coning to the wellbore occurs and water production results. Through the years considerable thought has been given to the water coning problem. More than 50 U. S. Patents have been granted to inventors on the subject. A relatively complete literature review of the water coning problem has been made. 5 A number of these patents hold considerable promise for the solution or the partial solution of the water and/or the coning problem. Very little has been written describing field tests of techniques for the suppression of water coning. A notable exception is the paperby West. 6 He reports success in reducing gas coning by a combination of gravel packing and oil injection above the oil-producing interval. He also describes a comparable method to prevent water coning, but provides no field examples. This study experimentally and analytically verifies the benefits of oil injection as a means of partially or completely suppressing the water cone. While the gas coning problem was not treated, it is anticipated that results comparable to those obtained in water suppression could be obtained with reduced oil injection since the viscosity contrast between oil and gas exceeds that between oil and water. For the purpose of this study, the conventional potential flow theory was applied to the water-coning problem. The experimental verification centered on both a radial and a linear model. The model study permitted the investigation of complex flow configurations and the use of fluids of differing densities and viscosities. No analytic expressions are available to permit a solution of the problem as stated (see Fig. 1).

By W. W. Stephens, W. J. Kroll, H. P. Holmes

THE only two methods for producing commercial quantities of malleable zirconium, up to now, have been using magnesium reduction of the anhydrous chloride under a neutral gas, and using purification of raw zirconium by the iodide dissociation method on a hot filament. The purity of the metal obtained by the latter process is about the same as that resulting from the chloride reduction, with the exception of the oxygen content, which may be about 0.05 pct lower in the iodide metal. Even traces of oxygen have a strong hardening effect on zirconium. Since, in the iodide process, the impurities, Si, Al, Fe, Ni, and Mg in the raw zirconium used, are carried over, it would appear uneconomical to use this method of refining solely to eliminate the traces of oxygen, unless very soft metal is desired. One important step to improve the iodide method, namely, dissociating pure iodide made from carbide and recycling the iodine, which would change this refining process into a method for extracting zirconium from the ore, has not yet been made. The Bureau of Mines, by using the chloride reduction, wanted to produce quantities of a reasonably pure and malleable metal at low cost for large-scale industrial use. This aim has been achieved, and a pilot plant permitting production of 600 lb of malleable zirconium per week will be described (fig. 1). Briefly, the Bureau of Mines process consists of reducing purified gaseous anhydrous zirconium chloride with fused magnesium under a noble-gas atmosphere. The reaction product, magnesium chloride, and any excess magnesium metal present are removed from the sponge zirconium in the next step by fusion and evaporation in a good vacuum at about 925°C. In this process, care is taken to keep air out of contact with the hot metal, which otherwise would contaminate the product with oxygen and nitrogen. Both these impurities embrittle zirconium even when present in an amount as low as 0.1 pct. A number of previous reports1-3 describe the method and the various improvements that finally led to a workable process. The major steps made were the production of large quantities of carbide, which is the raw material for producing the chloride, its chlorination with reasonable efficiencies, and the elimination of iron trichloride contained in the raw chloride, as well as that of the zirconium oxide which is always present in this product. The physical nature of the anhydrous chloride, which sublimes at 331°C at atmospheric pressure and melts at 420°C under a pressure of 25 atm, made it necessary to provide a special safety device on the purification and reduction vessels in the form of a lead-alloy seal, permitting escape of excess gases if pressure tended to build up. The main difficulties encountered in the reduction and in the following step, salt separation in a vacuum at elevated temperature, were caused by the material from which the reaction pot was constructed—iron. This metal reacts with zirconium at about 940°C with formation of a eutectic. The last step, salt separation by evaporation of the magnesium and magnesium chloride in a vacuum, is quite unconventional and has not been used before on such a scale. It is only due to the improved construction of high-vacuum pumps, especially oil-diffusion pumps, that such a method could be used. The various steps of the Bureau of Mines process, as described in the general outline above, may be summarized as follows: (1) production of the carbide, (2) chlorination of the carbide, (3) purification of the raw chloride, (4) reduction of the pure chloride with fused magnesium, (5) separation of excess magnesium and magnesium chloride in vacuum at elevated temperature, and (6) melting of the sponge obtained. Production of Carbide The arc furnace, described in a previous report,' was improved both to reduce the graphite consumption caused by the burning of the bottom plates and to concentrate the heat in order to obtain better power efficiency. This was achieved by providing the bottom with graphite plates entirely embedded in refractory bricks, the contact with the current being made with three water-cooled copper plugs. Figs. 2 and 3 show the arrangement. The crucible, made

Jan 1, 1951

By Paul D. Merica, O. B. J. Fraser

PROBABLY the first metallic objects used by man were nickel alloys. In search for flints suitable for the fashioning of their rude tools, our paleolithic ancestors, some 25,000 years ago, quite likely may have come upon some of those heavy, metallic fragments that we now know as meteorites, which consist of an alloy of nickel and iron containing usually from 5 to 15 pct of nickel. Whether paleolithic man ever did discover and use meteoritic fragments, his sketchy records do not actually disclose. We do know, however, that such fragments have been found and used by peoples, particularly the North American Eskimos, for weapons and implements in just the same manner as stones, and prior to any knowledge by those peoples of the reduction of metals from ores. Meteoritic showers were recorded frequently in earliest times and the meteorites often were found and fashioned into useful objects. The ancient Arabic and other myths of "invincible swords fallen from heaven" seem thus to have had a very definite basis in fact, and such weapons, of meteoritic material, have actually been re- covered from archeological excavations. It thus seems probable that meteoric nickel-iron was found and used long before iron was recovered by smelting iron ores (perhaps about 1200 B.C.) and probably even before there was knowledge and use of bronze and gold. Although many centuries were to pass before nickel was first isolated, in 1751, from Swedish ores and recognized as an elemental

Jan 1, 1953

By F. L. Wolf

THE catenary system of line construction possesses so many desirable characteristics from the operating standpoint that it has wide application for all types of electric traction. Many steam roads are electrifying sections of their lines, and in most cases are operating both steam and electric locomotives over the same track. This' means that the overhead catenary system is subjected to the severe corrosive action of locomotive smoke, and data concerning the resistance of various alloys to this form of corrosion are very desirable from every point of view. Reliable and specific information and data on the subject of corrosion due to steam and smoke from locomotives are extremely meager and, on this account, extensive service tests, together with accelerated tests, have been made on a number of commercial metals and alloys. The observations and data recorded in this paper are the result of a, preliminary test which was started in 1923 and which has been carried on to the present time. The recognition of the need for even more detailed and accurate data has resulted in the undertaking of another test which has been in progress for about a year. The result of this test will be published in due course. Some years ago The Ohio Brass Co. was asked by one of the large steam railroad companies to furnish data on construction details for a catenary system which it was considering for one of its divisions. The selection of, materials which would give the necessary physical characteristics as well as withstand the severe corrosive action of locomotive gases caused electrical railroad engineers considerable concern. At that time, there were available no specific or authentic data on these important questions: no systematic investigation of the problem appeared to have been made, even though its importance was generally recognized. Such observations as had been made were crude in that they had been limited largely to visual inspection which too frequently is most misleading. However, the scattered information which was collected gave important clues as to how best to start an investigation.

Jan 1, 1930

By O. H. Eschholz

THE electrostatic process of fume precipitation is an excellent example of the successful application of scientific knowledge to an industrial operation. Originally proposed for the precipitation of sulphuric acid mists, it has been extended until at present there is practically no fume carrying gas to which the method cannot be applied. Among the more common applications are: the recovery of non-ferrous smelter flue-dust, iron blast-furnace dust, cement dust, and potash fume. It should be borne in mind that the process is restricted to the precipitation of suspended particles, either liquid or solid, and does not separate gaseous constituents. However, -by proper temperature control, mixtures of vapors having different temperatures of condensation to either solids or liquids may he selectively precipitated. The process consists essentially of subjecting suspended particles, including those too minute to be effectively acted upon by centrifugal or gravitational forces, to such an electrical force that they are driven from the gas stream, acting as a conveyer, and deposited upon a suitable receiving surface. This directional impulse is obtained front the interaction of charged particles and an electrostatic field of definite intensity gradient existing between two dissimilar electrodes, known as discharge and receiving electrodes. In principle, the equipment is equally simple. As shown diagrammatically in Fig. 1, it consists of: (1) A source of high-potential direct current, requiring: (a.) Source of alternating-current energy. (b) Means of transforming from tow voltage to high voltage. (c) Means of converting alternating to direct current. (2) Precipitation chamber having: (a) Transmission tubes for fume-laden gases. (b) Suitably designed and disposed electrodes. (c) Means for affecting removal of deposited solids.

Jan 8, 1918