Search Documents

By K. H. Coats

This paper presents the development and solution of a mathematical model for aquifer water movement about bottom-water-drive reservoirs. Pressure gradients in the vertical direction due to router flow are taken into account. A vertical permeability equal to a fraction of the horizontal permeability is also included in the model. The solution is given in the form of a dimensionless pressure-drop quantity tabulated as a function of dimensionless time. This quantity can be used in given equations to compute reservoir pressure from a known water-influx rate, to predict water-influx rate (or cumulative amount) from a reservoir-pressure schedule or to predict gas reservoir pressure and pore-volume performance from a given gas-in-place schedule. The model is applied in example problems to gas-storage reservoirs, and the difference between reservoir performances predicted by the thick sand model of this paper and the horizontal, radial-flow model is shown to be appreciable. INTRODUCTION The calculation of aquifer water movement into or out of oil and gas reservoirs situated on aquifers is important in pressure maintenance studies, material-balance and well-flooding calculations. In gas storage operations, a knowledge of the water movemenr is especially important in predicting pressure and pore-volume behavior. Throughout this paper the term "pore volume" denotes volume occupied by the reservoir fluid, while the term "flow model" refers to the idealized or mathematical representation of water flow in the reservoir-aquifer system. The prediction of water movement requires selection of a flow model for the reservoir-aquifer system. A physically reasonable flow model treated in detail to date is the radial-flow model considered by van Everdingen and Hurst.1 In many cases the reservoir is situated on top of the aquifer with a continuous horizontal interface between reservoir fluid and aquifer water and with a significant depth of aquifer underlying the reservoir. In these cases, bottom-water drive will occur, and a three-dimensional model accounting for the pressure gradient and water flow in the vertical direction should be employed. This paper treats such a model in detail — from the description of the model through formulation of the governing partial differential equation to solution of the equation and preparation of tables giving dimensionless pressure drop as a function of dimensionless time. The model rigorously accounts for the practical case of a vertical permeability equal to some fraction of the horizontal permeability. The pressure-drop values can be used in given equations to predict reservoir pressure from a known water-influx rate or to predict water-influx rate (or cumulative amount) when the reservoir pressure is known. The inclusion of gravity in this analysis is actually trivial since gravity has virtually no efFect on the flow of a homogeneous, slightly compressible fluid in a fixed-boundary system subject to the boundary conditions imposed in this study. Thus, if the acceleration of gravity is set equal to zero in the following equations, the final result is unchanged. The pressure distribution is altered by inclusion of gravity in the analysis, but only by the time-constant hydrostatic head. The equations developed are applied in an example case study to predict the pressure and pore-volume behavior of a gas storage reservoir. The prediction of reservoir performance based on the bottom-water-drive model is shown to differ significantly from that based on van Everdingen and Hurst's horizontal-flow model. DESCRIPTION OF FLOW MODEL The edge-water-drive flow model treated by van Everdingen and Hurst1 is shown in Fig. la. The aquifer thickness b is small in relation to reservoir radius rb. water invades or recedes from the field at the latter's edges, and only horizontal radial flow is considered as shown in Fig. 1b. The bottom-water-drive reservoir-aquifer system treated herein is sketched in Fig. 2a and 2b. Here the aquifer

By Y. H. Liu, G. W. Powell

Thin foils made from the gold-rich region of- short (0.15 mm)Au-Ag diffusion couples annealed at 880°C for 1 hr were examined in ax electron microscope and the structures were compared with that of pure gold subjected to identical heat treatments. The couples underwent Plastic deformation (bending) during the diffusional anneal. The foils prepared from the diffusion zone have a higher dislocation density and incidence of subboundaries than pure gold. The plastic bending of the couple can be interpreted in terms of the climb of edge dislocations, which are pavallel to the bend axis, along the direction of diffusion. THE interaction of lattice defects during interdiffu-sion between two metals has been considered by several investigators. In particular, da Silva and Mehl,1 Barnes,' and Bardeen and Herring3 have proposed models based on interactions between point and line defects to account for the Kirkendall effect (marker movement). Each of these models is based on dislocation climb, which can either add or remove lattice planes, induced by an under- or supersaturation of vacancies. A theoretical treatment of the nucleation and growth of voids by the condensation of vacancies has been presented by Seitz.4 Stresses can arise in a binary diffusion couple as a result of the vacancy flux and the gradient in the lattice parameter. rinkmman' has investigated the effects of diffusion-induced stresses on void formation; the results of his analysis suggest that voids can form and grow under the influence of these stresses in the absence of an excess vacancy concentration. The relationships between vacancy supersaturation and diffusion-induced stresses and void formation have been elucidated also by Balluffi and seigle6 who concluded that the stress generated by a vacancy supersaturation aids the growth of voids. Experimental evidence which indirectly shows that stresses are produced by chemical diffusion has been obtained by several researchers.2,7-9 This evidence consists in part of the observation by light microscopy of the formation of subgrains, a process characteristic of the high-temperature deformation of some metals during creep.'0 More striking, however, is the plastic bending of short (0.2 mm) Cu-Ni couples observed by Barnes2 and of boron-doped silicon crystals reported by Queisser.9 Diffusion-induced dislocations in iron and silicon have been investigated by Ainslie et a1.11and Schwutte and Queisser,12 respectively, the former using transmission electron microscopy and the latter an X-ray transmission technique. Matthews and Crawford13 observed the formation of boundaries by the climb of interfacial misfit dislocations in thin, vapor-deposited Au-Pd couples diffused in situ in an electron microscope. In order to obtain additional information on the phenomena associated with defect interaction and diffusion-induced stresses in binary couples, an electron transmission study of foils prepared from the diffusion zone of short Au-Ag couples was undertaken. The initial objective was to investigate the processes occurring at various points of the diffusion zone. Subsequent research demonstrated that foils could be prepared only from the gold-rich region of the diffusion zone using the technique described herein. EXPERIMENTAL PROCEDURE Preparation and Annealing of the Diffusion Couples. The couples were made from annealed, high-purity (99.999 pct). polycrvstalline gold and silver sheets (0.075 mm thick). Shall (0.075 by 5 by 17 mm) elec-tropolished coupons of gold and silver were pressure-bonded by heating the two metals in a graphite device to 770°C and holding at this temperature for approximately 30 min. The quality of the bond was ascertained by metallographic examination at 150 times. Each couple subsequently was annealed at 880°C for 1hr; under these conditions, the extreme portions of the

Jan 1, 1968

By James G. Blaine, David A. Summers, L. John Tyler

There has been a considerable amount of research developed which shows that the close contour cutting of an excavation prior to removal of the central core will increase ground stability while concommitantly, reducing the number and size of blastholes required to create the excavation. To date, the industrial development of this technique has however, centered on the development of equipment based on simple cutter movement and mechanical rock cutting. The advent of reliable field operable high pressure waterjet cutting equipment with the very low reactive force required to hold the head in position has opened the way for a much smaller and more manueverable system. The advent of small, micro-computers allows the programming of accurate profiles for cutting tools on excavation equipment. The combination of these two technologies will allow the generation of complex as well as simple, excavation profiles and lead to the potential pre-support of the opening before major excavation is completed. A brief description of the necessary components and their functions is encorporated in the initial prototype design as given.

Jan 1, 1984

By Reno H. Sales

EVERY mine manager, mine geologist, and every prospector in the field who appraises the future of mining properties does so on the basis of a theory of ore deposition whether he recognizes this fact or not. Wherever the ultimate value of a mine or prospect is dependent upon undeveloped ore, any estimate by an engineer or geologist necessarily involves a theory of origin of the deposit. In view of these facts the importance of a thorough understanding of the genesis of ore deposits cannot be overestimated. It well may be that the greatness of our country will depend upon finding reserves of natural resources as yet undiscovered. The genesis of ore deposits offers a fascinating field for study and investigation. This is attested by the large number of geologists who have written at length on the subject. For progress made toward a better understanding of ore genesis we owe much to Kemp, Lindgren, Ransome, Vogt, Emmons, Spurr, Graton, and a host of others. Within my own experience, I have attempted to apply in practice the various concepts and theories that have been advanced by these men.

Jan 5, 1954

By J. F. Stiehr, R. L. Sanford, T. L. Myers

This paper summarizes the development of a Directory of Computer Programs Applicable to US Mining Practices and Problems. The directory is funded by the US Bureau of Mines and includes a sampling of computer usage in operating and manufacturing companies, consulting firms, computer companies, research organizations, universities, and various US government agencies. General references to computer applications throughout the mining industry are discussed as well as the availability of programs to interested organizations or individuals.

Jan 9, 1979

By E. M. Wise

THe properties required of gold alloys for jewelry are not well standardized, due in part to problems peculiar to certain branches of the jewelry industry, in part to the individual preference of the fabricator and to his willingness to cope with certain difficulties in manufacture, which arise with the use of certain alloys. General Requirements In general, the properties desired may be classed as follows: 1. Color should conform to the dictates of good taste and smart style. 2. Corrosion resistance and tarnish resistance should he good. This is to a considerable extent determined by the carat. Resistance to such corrosive agents as mercuric chloride as well as certain depi1atories is unreasonable to expect and difficult to meet. 3. Strength and hardness must be adequate to maintain the delicate contours of finely modeled jewelry. 4. Wear resistance must be great enough to resist abnormal wear, such as is encountered by a wedding ring in a lifetime of wear. 5. Ductility must be sufficient to permit the fabrication of drawn shells, tubes and difficult shapes. Material having a yield point of not less than 60,000 lb. per sq. in., an ultimate strength of 100,000 Ib. per sq. in., and an elongation of 40 per cent. is desirable. 6. Melting point should be between 800" and 1200" C. Colored Golds The popular green and yellow golds are based on the gold-silver-copper alloys; in some cases modified by the introduction of zinc to improve the casting properties and to alter the color, and nickel to increase the strength. The properties of the Au-Ag-Cu system have been the subject of a very thorough investigation by Jänecke,l Sterner-Rainer12 and Carter."

Jan 1, 1929

By E. M. Wise

THe properties required of gold alloys for jewelry are not well standardized, due in part to problems peculiar to certain branches of the jewelry industry, in part to the individual preference of the fabricator and to his willingness to cope with certain difficulties in manufacture, which arise with the use of certain alloys. General Requirements In general, the properties desired may be classed as follows: 1. Color should conform to the dictates of good taste and smart style. 2. Corrosion resistance and tarnish resistance should he good. This is to a considerable extent determined by the carat. Resistance to such corrosive agents as mercuric chloride as well as certain depi1atories is unreasonable to expect and difficult to meet. 3. Strength and hardness must be adequate to maintain the delicate contours of finely modeled jewelry. 4. Wear resistance must be great enough to resist abnormal wear, such as is encountered by a wedding ring in a lifetime of wear. 5. Ductility must be sufficient to permit the fabrication of drawn shells, tubes and difficult shapes. Material having a yield point of not less than 60,000 lb. per sq. in., an ultimate strength of 100,000 Ib. per sq. in., and an elongation of 40 per cent. is desirable. 6. Melting point should be between 800" and 1200" C. Colored Golds The popular green and yellow golds are based on the gold-silver-copper alloys; in some cases modified by the introduction of zinc to improve the casting properties and to alter the color, and nickel to increase the strength. The properties of the Au-Ag-Cu system have been the subject of a very thorough investigation by Jänecke,l Sterner-Rainer12 and Carter."

Jan 1, 1929

By Carl Samans

THE attention of physicists and metallurgists has been directed toward the study and explanation of the deformation textures in metals for the past 15 years. In 1920 N. Uspenski and S. Konobejewski1 were first able to show that the symmetrical X-ray diffraction effects that had been previously reported by E. Hupka2 and others in metal foils were caused by a directed arrangement of the crystallites. Since then, the systematic study of textures resulting from the application of the pure forces of tension or compression to polycrystalline materials hag been supple-mented by many investigations on deformed single crystals, which have greatly added to our knowledge of deformation. However, despite the valuable information secured from these comparative studies only four investigations upon cold-rolled single crystals of any of the face-centered cubic metals have been reported in the literature. This lack of quantita-tive data is especially unfortunate because of the much greater practical significance of rolling textures and their effects in both cold-rolled and annealed materials. This investigation was undertaken for the purpose of specifying the deformation of rolled single crystals in the hope that such information might later facilitate the explanation of polycrystal-line textures.

Jan 1, 1934

By H. Reinhardt, P. Haglund, J. Rydberg, B. Lunden

As legislation to minimize pollution in effluent streams becomes stricter, it is important to treat used acid pickling baths before discharge. This is usually achieved by neutralization of the acids and precipitation of the dissolved metals in such a way that neither acids nor metals can be re-used. A process has been designed and tested on a pilot plant scale to recover both acids and metals from a stainless steel pickling bath leaving only Na2SOs in the effluent. In this process, H2SOr is added to the spent pickling liquor and the recovery of the pickling acids HN03 and HF is achieved by solvent extraction, using TBP in kerosene as the organic solvent. The extracted acids are stripped with water, giving an acid concentration high enough for direct use in the pickling bath. Molybdenum is also extracted by TBP and is recovered in a separate step. The other metals, Fe, Cr and Ni, are precipitated from the raffinate as hydroxides, dried and recycled to the metal process. In evaluating this process, comparative experiments with mixer-settler and pulsed column have been performed. The process described is being considered for use by a Swedish company pickling 70,000 tons per annum of stainless steel.

Jan 1, 1973

By John Devine

DURING the past few years the Bureau of Mines has been studying hydrogen-sulfide corrosion in the petroleum and natural-gas industries. Early work was confined to investigating the various practical, or operat-ing, factors that control the corrosion reaction when ordinary mild steel is being attacked. In that work it was shown that, if the optimum operating conditions1 are obtainable, . gas containing hydrogen sulfide can be handled at ordinary temperatures without serious corrosion resulting. However, frequently "sour" gas must be handled under other than optimum operating conditions, and combating corrosion then becomes a problem to be considered more during the construction of a system than during its subsequent operation. That is, where economi-cally practicable in such cases the designer will seek to substitute for mild steel other steels or ferrous metals more resistant to corrosion by hydro-gen sulfide. The comparative resistance of various commercial steels and alloy steels to corrosion by hydrogen sulfide at elevated temperatures has been reported systematically by previous investigators,2 but similar information for corrosion at ordinary temperatures is available only from scattered sources, representing different methods of testing. As the value of comparative corrosion tests depends largely upon the use of a

Jan 1, 1934

By W. E. Hale, G. J. S. Govett

An orientation survey was conducted over a known disseminated copper deposit and a Au-Cu vein deposit and employed geological, geophysical, and geochemical methods. Geochemical techniques proved the most effective and economical means of locating and defining areas underlain by these types of mineralization. Six additional, widely separated occurrences were also investigated and mineralization was confirmed by determination of cold-extractable copper in stream sediments. The length of anomalous drainage varies from several to 16 km and depends on the type and tenor of mineralization. Despite generally marked relief and extreme physical and chemical weathering, cold-extractable copper anomalies in soils appear to reflect closely variations in the ore mineral content of immediately underlying rocks. Threshold values vary with local geological conditions and type and grade of mineralization. Significant thresholds in stream sediments are about 65 ppm and 10 ppm for cold-extractable copper in disseminated and vein copper occurrences respectively. Similar differences are encountered in soils. This necessitates the use of a scale of threshold values at progressive stages in each exploration program. Dis-seminated copper occurrences are presently the major source of mineral production m the Philippines. Much potentially productive ground remains to be investigated and applied geochemistry appears to offer the best available approach. The Institute of Applied Geology (I.A.G.), a joint project sponsored by the University of the Philippines, the Philippine Bureau of Mines and the United Nations Development Program (Special Fund) undertook during 1965-66 a number of field projects in Northern Luzon Island (Fig. 1). These field operations were of a two-fold nature and involved both orientation and exploration. During approximately six weeks, an orientation survey, involving geological mapping, geophysical surveying and geochemical prospecting, was conducted over a partly developed, disseminated copper deposit at Santo Nino (Fig. 1). This study demonstrated the economic and technical feasibility of geochemical ptospecting, relative to the other methods tested, for the location and delineation of a typical disseminated copper occurrence characteristic of those that represent the major source of metal in the Philippines.' Geochemical techniques, similar to those tested at Santo Nino, were then applied in a second orientation study of a vein occurrence at Suyoc (Fig. 1). The results of these two orientation studies suggest that, in reconnaissance work in this region, stream sediment analyses, combined with the determination of pH in the same streams, can be used to indicate areas underlain by rock containing anomalous concentrations of copper, whether it occurs in the large tonnage, low grade, disseminated deposits or in the comparatively small tonnage, higher grade, gold vein occurrences. Furthermore, the orientation surveys demonstrate that soil sampling and analysis serve effectively to outline more closely the mineralized zones within the generally anomalous areas identified from the stream reconnaissance. To further test the methods selected from the two earlier trials, six additional, widely separated prospects were investigated. The geological and geochem-

Jan 1, 1970

By Michael A. Toole, O&apos

INTRODUCTION The tremendous capital investment required to produce a low grade ore deposit demands a reliable answer to the question: "How much does it cost to drill a well to produce the uranium that geologists have indicated is there in the ground?" However, you will find the answers given will be many and varied, depending on whether they come from the operating company, the drilling contractor, a geologist, a reservoir engineer, purchasing agent, or whoever. Each generally considers only a limited area of the total operation. The operating company usually depends upon the drilling contractors, service companies, and consultants to supply expertise. Because it is often difficult to see the "whole picture" or even to agree upon what the "whole picture" is, planning a well program and its costs is often done piecemeal. Frequently, costs "saved" in one area of the program are needlessly spent in another, because the effect of one area upon the other was overlooked. Since the drilling fluid is such an influential part of the drilling program, it should be given utmost consideration when planning the overall program. As W. D. Lacabanne wrote in 1954: "The drilling fluid system is understandably called the heart of the rotary oil drilling rig. Any other type of rotary rig.... should benefit by the incorporation of mud fluids in the drilling scheme." And G. R. Gray mentions that "The driller recognizes the drilling fluid as one of the useful tools available to solve drilling problems." However, in minerals drilling, only in recent years has the drilling fluid been considered as more than a tool to get through special problem areas. Although there are many similarities between drilling for oil and gas and drilling for minerals, the differences in the drilling equipment used justifies designing specific fluids for the minerals drilling industry. NL Baroid/NL Industries, Inc. has been a leader in introducing such fluids and in providing technical know-how to the minerals drilling industry. The purpose of this paper is: (1) to discuss the selection of drilling fluids to meet specific drilling conditions during both exploration and production and (2) to show the interrelationship among factors present in the exploration and production phases that influence total well costs. DRILLING FLUIDS FOR DRILLING PROBLEMS The drilling fluid is a tool that can be used to improve drilling performance by improving hole cutting, cleaning, stability, and formation productivity. Properly formulated and maintained drilling fluids enable the drilling operation to be carried out with increased efficiency and lower total (overall) costs. However, it should be noted that not all drilling problems can be solved by even the most carefully prepared and maintained drilling fluids. Of the many possible drilling problems encountered in a well before reaching target depth, this paper will discuss only those most likely to be present in the shallow [61 to 610 m (200 to 2000 ft)] drilling operations in South Texas. LOST CIRCULATION Loss of circulation is the most common problem encountered in drilling. Because the losses occur under varied conditions, it is often difficult to determine the exact causes. "Lost circulation" or "lost returns" means the partial or complete loss of drilling fluid to voids in the formation. "Loss of water" while drilling with water may take place into any permeable section and should be distinguished from "water loss" or filtration of fluid through the filter cake of mud solids laid down on a permeable formation. "Loss of water" can frequently be stopped by the addition of colloidal sized clay particles such as high yield bentonites, whereas "water loss" may be controlled with organic polymers. Subsurface conditions that lead to loss of circulation can be classified as: (1) natural fractures, (2) induced fractures, (3) unconsolidated or highly permeable formations (loose gravel), and (4) cavernous formations (crevices and channels). Loss of circulation may occur whenever the borehole pressure exceeds the formation pressure. The greater the differential pressure, the more likely it is that circulation may be lost. To stop loss of whole mud, voids must be bridged so that a filter cake can be laid down on the permeable section. The plugging material must be of the proper size and shape to offer greater resistance to the fluid flow around it than the flow up the annulus. A plugging composition that satisfies these requirements may not be able to be handled by the small rig pump available.

Jan 1, 1979

By J. Richard Maier

Short-range mine planning (less than five years) previously was accomplished using contour and isopac maps, pencil and paper, an abacus, and our lucky quarter. Through the use of both micros and mainframe time sharing, Glenrock Coal Company (GCC) has been able to virtually put the old equipment away (except the problem solving quarter). In the process, GCC has saved many man-days and eliminated the more tedious parts of mine planning, such as picking elevations off a map with an engineer's scale and repetitive calculations. These savings have allowed GCC to do a more extensive job of mine planning as well as offer more alternatives, making GCC better prepared for possible economic changes. Mine planning, simply, involves looking at what has been done and deciding what needs to be done using various constraints. The application of this concept is not as easy as it sounds. The need for experience and insight cannot be replaced by a machine, but machines can supplement a person's ability by doing the bookkeeping and the repetitive work. Through the application of computers and their accessories, GCC has brought mine planning to a more modernized state. The following paper will detail the development and use of one system as used at GCC. Please note: In the figures and tables following, some of the data has been altered to protect confidential information used in mine planning.

Jan 1, 1983

ALTHOUGH the refining period of the heat is generally defined as starting after the charge has been completely melted, it may more properly be considered as beginning with the first efforts to facilitate the shaping up of the slag and the making of corrective additions for the control of slag or metal composition. Such actions may be initiated during the latter half of the lime boil. The early part of the refining period may, then, in essence overlap the latter part of the melting period. The primary aims of the refining period are: (1) to reduce phosphorus and sulfur from the steel bath to levels safely below the maximum contents specified; (2) to eliminate carbon to a specified level as rapidly as possible and still allow time for proper conditioning of the slag and attainment of the necessary bath temperature; and (3) to have the heat ready for tapping or furnace deoxidation, with slag in the proper physical and chemical condition, and with carbon and oxygen contents and the temperature of the steel at the proper levels for the composition and grade of steel being produced. The particular conditions that fulfill these aims are distinctly different, depending upon whether the steel is to be finished according to fully killed. semikilled, or rimming practice and also depending upon the carbon range specified. Regardless of the type of charging practice employed, the object of the refining period is to produce repeatedly the desired finishing and tapping conditions for the grade of steel being produced. The variations and proportions of raw materials used in the charge may cause some variations in the degree of control required during refining, but not in the method of control. The refining period can therefore be discussed from a viewpoint largely independent of charging and melting practice. SHAPING UP THE SLAG In the first helper's vocabulary, refining practice consists in

Jan 1, 1951

By J. S. Johnson, W. C. McCulloch

All phases of plant operation must be synchronized so that the A number of interruptions in the flow of material may be reduced to a minimum. In the majority of plants operating under a labor agreement, time lost during the operating shift cannot be made up with overtime. With the work week restricted to 35 hr., the ratio of productive time to total time justifies extra effort in keeping the plant operating at capacity during the productive shift. This does not apply when central plants with adequate storage are operated by multiple shifts. In such installations the problems become similar to those of any factory or mill where added units, parallel circuits, or excess capacity serve to maintain the average production during intervals of maintenance shut- down. These plants, by special agreement, may run continuously, barring mechanical interruptions. The control of plant operation is in those procedures that are practiced to obtain from the run-of-mine product a high recovery of clean coal products to meet adopted trade standards and consumer specifications at the lowest possible cost. Correlation of all factors for continuous operation requires more than mechanical perfection in the plant. The run-of-mine coal must be delivered to the preparation plant without delays and the clean coal and refuse products taken away. Power supply and water requirements must be adequate. Signal systems must be established for emergency stops and to facilitate resumption of coal flow.

Jan 1, 1943

By J. L. Lamont, W. Crafts

Studies of the effect of composition of steel on hardenability by Grossmann,' and as-quenched hardness by Field2 and by the authors, have made it possible to predict the results of quenching when the composition and cooling rate are known In order to extend the application of the hardenability calculation to the quenched and tempered condition in which steel is finally used, a survey has been made of the hardness changes caused by tempering. From this study a method has been developed for the prediction of hardness and tensile strength of steel in the tempered condition. The method of calculation was developed from Rockwell C hardness tests on quenched and tempered Jominy specimens and is expressed in Rockwell C hardness units. It is of an additive type in which the degree of softening from as-quenched hardness is estimated. Tem-pred properties may be calculated within about plus or minus 5 Rockwell C hardness or plus or minus 15,000 lb. per sq, in. tensile strength. This degree of accuracy is less than that necessary for the control of heat-treatment, but is adequate for the comparative evaluation and selection of alloy steels. The formula indicates that tempered hardness is primarily dependent on as-quenched hardness and, as in the hardening reaction, the progress of tempering is controlled mainly by the carbon content. Alloys tend to retard softening by a secondary hardening mechanism in which the alloy appears to migrate from ferrite to the carbide phase. The factors for the effects of alloys in tempering vary so much from the effects of alloys in hardening that different steels of equivalent hardenability may, after like heat-treatment, differ considerably in tensile strength. Procedure In developing the method for calculating tempered Rockwell C hardness, simple and complex steels were tested over a range from 0.08 to 0'65 per cent carbon and up to 2.68 per cent manganese, 2.18 silicon, 3.50 chromium, 4.94 nickel, and 1.06 molybdenum. The steels were made as small induction-furnace heats at the Union Carbide and Carbon Research Laboratories, Inc' The accuracy of the method was finally checked on a variety of carbon, low-alloy and high-alloy types of heat-treating steels produced under commercial conditions. The method was based on a study of tempered Jominy bars, and its validity was tested by correlation with the center hardness and tensile strength of oil-quenched and tempered bars from 1/2 to 4 in. in diameter. The method of calculation was derived from the differences in Rockwell C hardness between as-quenched and quenched and tempered Jominy specimens. Prenormalized Jominy hardenability speci-menS quenched from a normal temperature for austenitizatios were used to obtain a range of as-quenched Rockwell C

Jan 1, 1948

By W. Crafts, J. L. Lamont

Studies of the effect of composition of steel on hardenability by Grossmann,' and as-quenched hardness by Field2 and by the authors, have made it possible to predict the results of quenching when the composition and cooling rate are known In order to extend the application of the hardenability calculation to the quenched and tempered condition in which steel is finally used, a survey has been made of the hardness changes caused by tempering. From this study a method has been developed for the prediction of hardness and tensile strength of steel in the tempered condition. The method of calculation was developed from Rockwell C hardness tests on quenched and tempered Jominy specimens and is expressed in Rockwell C hardness units. It is of an additive type in which the degree of softening from as-quenched hardness is estimated. Tem-pred properties may be calculated within about plus or minus 5 Rockwell C hardness or plus or minus 15,000 lb. per sq, in. tensile strength. This degree of accuracy is less than that necessary for the control of heat-treatment, but is adequate for the comparative evaluation and selection of alloy steels. The formula indicates that tempered hardness is primarily dependent on as-quenched hardness and, as in the hardening reaction, the progress of tempering is controlled mainly by the carbon content. Alloys tend to retard softening by a secondary hardening mechanism in which the alloy appears to migrate from ferrite to the carbide phase. The factors for the effects of alloys in tempering vary so much from the effects of alloys in hardening that different steels of equivalent hardenability may, after like heat-treatment, differ considerably in tensile strength. Procedure In developing the method for calculating tempered Rockwell C hardness, simple and complex steels were tested over a range from 0.08 to 0'65 per cent carbon and up to 2.68 per cent manganese, 2.18 silicon, 3.50 chromium, 4.94 nickel, and 1.06 molybdenum. The steels were made as small induction-furnace heats at the Union Carbide and Carbon Research Laboratories, Inc' The accuracy of the method was finally checked on a variety of carbon, low-alloy and high-alloy types of heat-treating steels produced under commercial conditions. The method was based on a study of tempered Jominy bars, and its validity was tested by correlation with the center hardness and tensile strength of oil-quenched and tempered bars from 1/2 to 4 in. in diameter. The method of calculation was derived from the differences in Rockwell C hardness between as-quenched and quenched and tempered Jominy specimens. Prenormalized Jominy hardenability speci-menS quenched from a normal temperature for austenitizatios were used to obtain a range of as-quenched Rockwell C

Jan 1, 1948

By G. K. Manning, E. R. Stein, E. E. Underwood

Columbium, carbon. and nickel additions were made to iron-base alloys with 20 pct CY. The effects on microstructure, precipitation-hardening characteristics, and High-temperature properties were investigated by means of metallographic, hot-hardness, and magnetic measurements. An austenitic alloy consistilzg of Fe-20Cr-14Ni-0.8C-2.5Cb had higher hot-lzaciness at 1700°F than the other alloys investigated. Its favorable standing is attributed to an enhanced interaction of Cb and Cr4C particles dispersed within a stable austenitic matrix. FOR the past 20 years, cobalt- and nickel-base alloys have been used for the more stringent high-temperature applications because of their excellent creep resistance. Although their performance is quite satisfactory, other base materials must be considered for large tonnage, low-cost applications such as for the automotive gas turbine. Iron-base alloys are also used extensively, but at somewhat lower temperatures, primarily because of the instability of particles or because precipitation occurs at relatively low temperatures. Since unusual stability has been reported for Fe-Cb and Cb-C compounds.1-3 it was hoped that effective amounts of these compounds could be taken into solution at temperatures just below the melting range, then precipitated upon reheating. Actually, strengthening was found to occur by both precipitation hardening in some alloys and by phase transformations in others. Among the alloys investigated, that with the best high-temperature properties owes its strengthening to a combination of carbide particle interaction and a relatively stable austenitic matrix. EXPERIMENTAL PROCEDURES Small preliminary melts of about 100 g were made in a vertical Glotube furnace, using alundum crucibles and an argon atmosphere. Alloys weighing 35 lb were melted in a basic-lined induction furnace, also under argon. The compositions of the alloys are given in Table I. The nickel-free alloys were usually ferritic, while those containing nickel were generally austenitic. Depending upon the particular heat treatments, or the combination of alloying elements, two-phase alloys of ferrite and austenite could be obtained. In the following text, however, the nickel-free or nickel-bearing alloys are referred to simply as either ferritic or austenitic alloys respectively. The small ingots were swaged at 2000°F, in steps, to rods of approximately 3/16-in. diam. The large ingots were forged at 2100°F to 1-in. sq bars. No difficulties were encountered in swaging or forging any of the alloys to as much as 90 pct reduction in area. For heat treating at temperatures above 2000°F, specimens were sealed in quartz tubes under a partial pressure of helium. No special precautions were found to be necessary at lower temperatures. Intermetallic compounds in the preliminary alloys were identified by means of X-ray diffraction measurements. Correlation of these results with micro-structural characteristics (such as color, shape, size, and location) of the compounds aided in their identification. Magnetic susceptibilities were also obtained at room temperature with a Magne Gage instrument after the various heat treatments. To

Jan 1, 1962

By A. N. Mitinsky

Discussion of the paper of A. N. MITINSKY, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 104, August, 1915, pp. 1697 to 1705. LAWFORD H. FRY, Burnham, Pa. (communication to the Secretary*). -The author assumes that the proportional limit and the elastic limit are coincident or very nearly so, and then further assumes that the stress corresponding to these two points is the least stress which if repeated will cause failure. The point is extremely interesting and it is to be regretted that the author did not quote experimental data to show the relation between the limit of repeated stress and the other properties of the material. The author's suggestion that a steel of poor quality may have a normal value for the yield point and tensile strength (see Fig. 2) and an abnormally low elastic limit, and that this will correspond to a low resistance to repeated stress, may account for a number of failures of axles in which the tensile tests show normal physical properties. If so and if a determination of the proportional limit would have eliminated the material before it was put into service, this determination will merit most earnest attention. It appears, however, that considerable further research is necessary before any definite conclusion as to the quality of a steel can be drawn from its proportional limit. Mr. Mitinsky's paper is extremely interesting and if it stimulates thought and work along the lines indicated, it may prove of considerable practical benefit. H. V. WILLE, Philadelphia, Pa.-The paper discusses the difference between the proportional limit, or elastic limit, and the yield point, and refers to the fact that much harm results from confusion of the terms yield point and elastic limit. Similar confusion has arisen in this country; the American-Society for Testing Materials does not even consider the elastic limit and proportional limit to be identical and recently adopted the following definitions:

Jan 12, 1915

By George Sachs

THE process of recrystallization has not as yet been explained satis-factorily. Some definite conclusions could be drawn from recent investi-gations, such as, for example, that recrystallization is a process of nucleus formation and crystal growth 1and that the orientations of the nuclei correspond to some fragments of the original crystals, which have been considerably distorted during deformation.2 There are, however, a number of metals and alloys crystallizing in the face-centered cubic system, which form a particularly simple orientation if recrystallized as a sheet.3 Such a sheet is almost a single crystal with the cubic axes parallel to the rolling, transverse, and normal directions of the sheet. This preferred cubic or (100) orientation of the recrystallized sheet has been considered to be very different from the rolling structure of the same metals,4 but there are two reasons why this last supposition remains open to controversial discussion. The first reason is academic: In practically all cases except the one mentioned above, close correlations and similarities between rolling and annealing orientations have been observed; for instance, in iron and steel sheet.6 Secondly, no deformed metal actually forms a-simple orientation. In any thoroughly investigated case a number of different orientations and considerable scattering or deviations from the ideal orientations have been found., It is generally true that investigations on single crystals have shown that a definite orientation is approached in stretching or in compression of an originally undisturbed crystal.7 In the special cases, however, where the initial orientation was close to an important crystallographic direction that differed from the final "ideal" orientation, the resulting orientation changed very little by deformation, staying somewhere in the vicinity of the initial orientation." Such deviations

Jan 1, 1940