Search Documents

By C. G. Dunn

NUCLEI that are formed during the recrystallization of a grain following plastic deformation generally have orientations that differ from the original. This aspect of recrystallization may be described in terms of orientation changes. It was shown previously, in an investigation on recrystallization in silicon ferrite,1 that the observed orientation changes were highly improbable on a chance basis, and that some mechanism must be involved. Analysis showed that the data could be satisfactorily classified into the smaller of two subclassesf of the 36 third- order twin transformations. No attempt was made at that time to classify the data within the special class of 12 third-order twin transformations, although results did indicate a greater probability for some of them to occur. A classification of this type would be more valuable, of course, with more data on orientation changes per old deformed grain. The present work fulfills this condition to some degree and also extends the scope of the investigation to include the effects of original orientation and the amount of plastic deformation. The effect of original orientation is of considerable interest because of the known effects of orientation on plastic deformation, particularly with regard to degree of fragmentation and the formation of de- formation bands, and because the orientations produced by deformation should influence the orientations obtained through recrystallization. Barrett and Levenson2 reported that single crystals of iron deformed in the range 82 to 97 per cent could be put into three general classes; namely, crystals in class I maintained a reasonably sharp single orientation, those in class 2 transformed into two distinct orientations, and those in class 3 changed into a large number of major and minor orientations. Something similar would be expected for silicon ferrite crystals, and verification of this for a few cases of types class I and class 2 deformation has been reported elsewhere3 for single crystals of silicon ferrite cold-rolled in the range 10 to 20 per cent. As an example of class 2 deformation, it was shown that a crystal of silicon ferrite cold-rolled in a {110} plane in a < 100> direction developed two layers, or deformation bands differing in orientation. When this happens it is possible to etch away one band and leave a single structure for use in studying the orientation changes that occur during recrystallization. when preferred crystal orientations are obtained in recrystallization, it is notparticularly necessary to evaluate groups of common orientation, as was done previously (ref. I, Table 6); but an

Jan 1, 1946

By James Norman, Benjamin S. Lindsey

Barite (BaSO4) is the most important industrial barium mineral from the standpoint of quantity consumed. In 1938 the amount was 365,000 tons. Its uses are numerous, some of the more important being in the production of pigments, as an inert filler in a wide variety of products, as a weighting material in oil-well drilling muds, in the manufacture of some binds of glass, and in the production of barium chemicals. The barite studied in this investigation occurs as the massive variety in a shale replacement formation near Magnet Cove, Ark. It is intimately mixed with quartz and small amounts of iron oxide and residual shale. Complete liberation of barite and quartz is not obtained when the rock is ground to I00 per cent through 325 mesh. The crude rock with which all test work was done assayed 85.1 per cent BaS04, II.II. per cent SiO2, and 2.85 per cent R2O3. Its specific gravity was 4.03. It was found in the course of the investigation that the barite contained a small amount of uniformly distributed carbonaceous material, so intimately dispersed that it could not be seen with the microscope, but gave a definite gray cast to the barite concentrates. The color of the barite in polished sections of the crude rock ranged from gray to almost black, while finely ground powder was a reddish gray. The reddish hue was due to the iron oxide present. In 1939, under the supervision of Oliver C. Ralston,* the Bureau of Mines, in cooperation with the Milwhite Company, of Houston, Texas, undertook to study the flotation of barite from Magnet Cove, Ark. Flotation of several southern barite ores had already been investigated by the Bureau of Mines.&apos; The Magnet Cove barite was unique, however, in that it had to be ground to such an extremely small particle size for liberation. The flotation of non-metallic minerals in the presence of a large amount of slime is usually very difficult, and when done is an innovation calling for conditions different from those under which granular material is separated. Laboratory Flotation Work Preliminary investigation showed that the flotation reagents recommended by O&apos;Meara and Coel for separating barite and siliceous material were suitable, but much larger quantities of reagents were required to separate such finely divided material. Moreover, it was found that careful control of the frothing was necessary. When oleic acid and sodium silicate were used a voluminous froth was observed at the beginning of a test, and toward the end there was not enough froth to effect complete recovery of barite. The addition of pine oil as a frother gave proper frothing for the duration of the test, and the substitution of coconut fatty acid (crude lauric acid) for oleic acid produced a more heavily burdened froth. Two different paper-mill fatty-acid products were tested

Jan 1, 1943

L. C. UREn,* BerkelEy, Cal. (written discussion).—I heartily concur with Rlr. .Fobs concerning the need for advanced courses on various phases of Petroleum Engineering. I think that his criticism is probably true of most of the engineering schools that are specializing at all in Petroleum Engineering, that is, that most of their so-called graduate courses are not of graduate caliber but are merely more specialized aspects of undergraduate subjects. It would undoubtedly be to the advantage of the petroleum profession if more advanced work could be offered in a few of the leading engineering institutions so that there would be something substantial to offer graduate students wishing to return after a period of undergraduate work, for additional training. There is no doubt but that a better trained engineer, more useful to the oil industry, could be secured from schools offering such advanced training. The problem of adpting our instruction to fit the needs of engineers trained along other lines who wish, after completion of their undergraduate work, to enter thc petroleum engineering field, is a more difficult one. It has been my experience that such men are usually sadly deficient along certain lines and that they are really not prepared for the more advanced work in Petroleum Production Engineering until they have gone back over the work which they have missed in their undergraduate training. I note that Mr. Fohs suggests that other eastern and western colleges not now stressing Petrolelim Engineering, should be encouraged to take up advanced work of this character. With this, however, I cannot agree unless the institutions arc also prepared to offer a full sequence of undergraduate work on which the more advanced courses may be superimposed. Whether or not there is a need for additional engi-ncering colleges entering the petroleum engineering field is an open qucstion. I believe that we arc turning out enough petroleum engineers at the present time and that none of the six institutions now specializing in this field arc overcrowded. Morc-ovcr, they are fairly well distributed over the country, though there may be room for an additional school in the field in the eastcrn section of the United States. F. W. Padgett, Norman, Okla. (written tliscussion).—Assuming that the stnclcnt has the proper fundamentals, that is, general science and a knowledge of the technology of the industry, then the problem is: What courses should be offered from the graduate standpoint? (a) Course Work.—His knowledge of the technology of the industry can be extended advantagcously by means of one and two-hour courses, which consist in a more detailed survey of the various branches of the industry. (b) Lilerdure.—This work may, or may not, be connected directly with his research problem. The student should become familiar with methods of locating articles in the 1iterature; should also become familiar with all the important original

Jan 1, 1928

By Benjamin S. Lindsey, James Norman

Barite (BaSO4) is the most important industrial barium mineral from the standpoint of quantity consumed. In 1938 the amount was 365,000 tons. Its uses are numerous, some of the more important being in the production of pigments, as an inert filler in a wide variety of products, as a weighting material in oil-well drilling muds, in the manufacture of some binds of glass, and in the production of barium chemicals. The barite studied in this investigation occurs as the massive variety in a shale replacement formation near Magnet Cove, Ark. It is intimately mixed with quartz and small amounts of iron oxide and residual shale. Complete liberation of barite and quartz is not obtained when the rock is ground to I00 per cent through 325 mesh. The crude rock with which all test work was done assayed 85.1 per cent BaS04, II.II. per cent SiO2, and 2.85 per cent R2O3. Its specific gravity was 4.03. It was found in the course of the investigation that the barite contained a small amount of uniformly distributed carbonaceous material, so intimately dispersed that it could not be seen with the microscope, but gave a definite gray cast to the barite concentrates. The color of the barite in polished sections of the crude rock ranged from gray to almost black, while finely ground powder was a reddish gray. The reddish hue was due to the iron oxide present. In 1939, under the supervision of Oliver C. Ralston,* the Bureau of Mines, in cooperation with the Milwhite Company, of Houston, Texas, undertook to study the flotation of barite from Magnet Cove, Ark. Flotation of several southern barite ores had already been investigated by the Bureau of Mines.&apos; The Magnet Cove barite was unique, however, in that it had to be ground to such an extremely small particle size for liberation. The flotation of non-metallic minerals in the presence of a large amount of slime is usually very difficult, and when done is an innovation calling for conditions different from those under which granular material is separated. Laboratory Flotation Work Preliminary investigation showed that the flotation reagents recommended by O&apos;Meara and Coel for separating barite and siliceous material were suitable, but much larger quantities of reagents were required to separate such finely divided material. Moreover, it was found that careful control of the frothing was necessary. When oleic acid and sodium silicate were used a voluminous froth was observed at the beginning of a test, and toward the end there was not enough froth to effect complete recovery of barite. The addition of pine oil as a frother gave proper frothing for the duration of the test, and the substitution of coconut fatty acid (crude lauric acid) for oleic acid produced a more heavily burdened froth. Two different paper-mill fatty-acid products were tested

Jan 1, 1943

By B. D. Cullity

A distribution of residual stress after plastic elongation is proposed, in which the bulk of the material is strained in compression and a very small portion in tension, This distribution is shown to account both for the X-ray observations and for the effect of plastic straining on magnetic losses in silicon steel. The regions left in compression are tentatively identified with the interiors of the sub-grains revealed by the electron microscope. THIS paper is concerned with the general problem of the nature of the residual stress which is produced in metals by plastic elongation. A particular stress distribution will be suggested which accounts for the main X-ray diffraction observations which have been made. It will also be shown that certain magnetic measurements made on silicon steel can be understood in terms of this stress distribution. X-RAY OBSERVATIONS Uniform straining of a crystal lattice (macro-strain) causes a diffracted X-ray beam to shift its position, and nonuniform straining (microstrain) causes line broadening. If a bar of metal is plastically elongated in the longitudinal x direction and then unloaded, diffracted X-ray lines are observed to be both shifted and broadened.&apos;-= Although the observed line shift indicates the presence of macro-strain, experiments have shown that no macrostrain, in the usual engineering sense of the term, exists.5"7 For example, removal of a layer from one surface of a stretched and unloaded bar does not produce curvature in the remainder of the bar 5&apos;7 Fig. 1 shows the variation of lattice strain in the x direction, as determined from X-ray line shifts, with the applied stress in the same direction. The curve ABC is the normal stress-strain curve of the material, AB being the elastic portion and BC the plastic. In the elastic region AB, the strain measured by X-rays, called the lattice strain, and the strain measured mechanically are both proportional to the applied stress, and both return to zero when the applied stress is removed. Above the elastic limit the lattice strain would be expected to continue to increase along the line BD. Actually, it increases less rapidly with respect to stress, or even decreases, as shown by BE. If the applied stress is then decreased, the lattice strain decreases along EF, which is parallel to AB. As a result, there is a compressive residual lattice strain FA after unloading. STRESS DISTRIBUTION. Since a stretched and unloaded bar does not contain macrostress, it follows that the observed line shift must be due to a special distribution of mi-crostress. Such a distribution is shown in Fig. 2, which shows the variation of the stress u, across a stretched and unloaded bar. The material is assumed to consist of two kinds of regions: regions C, stressed more or less uniformly in compression, comprising the bulk of the volume of the material and responsible for the observed diffrac-

Jan 1, 1963

By William F. Butler, Mo-Hung Che

DEVELOPMENT OF MONEY AND MONEY STANDARDS This chapter is concerned with the rise, and then the decline and fall, of gold and silver as monetary metals. As a first step in tracing the history of this process, it is necessary to consider the nature of money, and the manner in which different forms of money have developed over the centuries. The origins of money go back into deepest antiquity. Once men ceased to be pure nomads and entered into even a rudimentary form of society such as clans or tribes, money had to be invented The first step was barter as farmers or hunters swapped their surplus products for things produced by artisans such as shoes, clothing, and simple tools. But such barter trading is inconvenient even in primative societies It is difficult to match up buyer and seller at any point in time There are problems in arriving at viable and acceptable terms of exchange. The accumulation of savings-wealth-is complicated. No one can be sure that a pile of furs, or wheat, or certainly fish or game can be used in the future to trade for other goods or services. So even prehistoric man saw the need for money. There was a need first for something to serve as a medium of exchange This was an essential first step in the process of specialization-or the division of labor. A farmer, a hunter, or a shoemaker could only devote his full efforts to his trade if he could be sure that he could exchange his surplus production for the other things he needed for existence. This required a medium of exchange-a form of money which would be broadly acceptable. Money was needed for two other reasons Some system of market prices was essential to facilitate the exchange of goods and services. This required some form of common denominator-some standard of value-to govern the exchange process. And there was also need for something to serve as a store of value, a place to put any excess production (savings) with the assurance that it can be used in the future to acquire a general range of goods and services. As a result, money, in one form or another, developed at a very early state in civilization. Yet the centuries have been marked by a search for a form of money which will possess in full measure all of the attributes in money-a reliable and universally acceptable medium of exchange, standard of value, and store of value. -A wide variety of things have been used as money at one time or another: shells, beads, stones, feather, metals, and even the teeth of sharks and dogs. Some of these things were obviously of little or no practical value. They were used because people had confidence in their continued acceptance as a medium of exchange. As the world evolved and as trading ex-

Jan 1, 1976

By James Terry Duce

The symposium on production for the year 1940 contains few papers on the foreign situation. It is probable that the foreign part of next year&apos;s symposium will be even shorter. This is due to rigid censorship in various countries, as the question of the volume of petroleum supplies has become one of great strategic importance. This is even more true than in the last war, owing to greater mechanization of armies. &apos;It has always been the policy of officers in charge of the symposium to refrain from publishing information that might possibly injure national or private interests. At the close of the war we hope again to publish full and accurate records of production abroad. Excerpts from Circular to Authors In order to facilitate interpretation of the data in this chapter, we print the following excerpts from the Circular to Authors. The field is the unit in this tabulation. In cases of fields extending across State boundaries, such as Rodessa, it is suggested that each State author treat the section of the field in his State as a unit, and by a footnote indicate that the field extends into an adjacent State. Each space in Table I may represent one of four possibilities; either it is not applicable to the particular field, or the proper entry is not determinable, or the proper entry may be determinable but is not determinable from data available to the author, or the proper entry is determinable. When spaces are not applicable, leave blank; in spaces where the proper entries are determinable but not de-terminable frod data available to the author, please inserty; in spaces where the proper entries are determinable by the author, make such entries. y implies a hope that in some future year a definite figure will be available. The entry of a zero is a positive declaration, and an important declaration where it is in order. Inability to determine precisely the correct entry for a particular space should not lead the author to insert merely y. Contributions of great value may be made by the author in many cases where entries are not subject to precise determination. In sucli cases the author should use his good judgment and make the best entry possible under the circumstances. For many spaces the correct entries represent the opinion of the author (for example, "Area Proved&apos;) and in such cases the entry need not be hedged to such extent as when the quantities are definite yet can be ascertained only approximately by the author. In cases under definite headings but where figures are only approximate, the author may use x. It is thought that the nearest whole numbers are sufficiently accurate for our purposes except as to percentage of sulphur in oil. If an author desires to report any other figures to tenths, he may do so. The quantity of gas produced should include, where possible, gas sold or otherwise marketed, and gas blown into the air, burned as flares or otherwise wasted. Segregation of these figures would be interesting if the authors can make such segregation. In any event, the figures should represent as nearly as possible the total quantity of gas removed from the reservoir. Under the columns on "Depth," the average depth to the top of the productive zones and to the bottom of the productive wells, when

Jan 1, 1941

By H. O. Jahns

This paper describes the application of regression analysis for obtaining a two-dimensional areal description of heterogeneous reservoirs from short-term pressure-time data such as that obtained in interference tests. The method replaces the time-consuming trial-and-error procedure commonly used to match field data on an electric analyzer or digital computer with a systematic search which is programmed for a computer. The computer program adjusts the properties of a reservoir model automatically until a least-squares fit is obtained between observed and calculated pressure data. The reservoir is simulated by a single-phase, compressible, two-dimensional model. It is divided into a number of homogeneous blocks whose transmissibility (kh/F) and storage (Fch) values are varied to obtain the least-squares fit. The reliability of these values is determined from their standard deviations and correlation coefficients. Although the method is rigorously applicable to single-phase flow only, multiphase flow can be handled provided saturation changes are small during the test. Possibly the method can also be used to obtain a reservoir description from pressure-production history, but this application is outside the scope of this work. The paper includes, in addition to a description of the numerical procedure, a discussion of some of the problems associated with the method. Rules are given to help in selecting the number of homogeneous blocks and deciding upon their arrangement. The uniqueness of a reservoir description is considered. Finally, the use of the method is illustrated by the interpretation of field data from two interference tests. INTRODUCTION Pressure data from short-term transient tests, such as single-well and interference tests, are widely used to obtain reservoir properties. These tests are usually analyzed by assuming a simple reservoir model; very often, a homogeneous one is used. As a result, analysis of the transient data from each well frequently gives different values for reservoir properties. The problem then arises to combine all these differing results into a more detailed picture of the reservoir. One technique is to simulate the reservoir with a digital computer or with an electrical analyzer and to adjust the reservoir parameters by trial and error until the simulated pressure data are in reasonable agreement with the observed pressure data for all wells. Although this method has been used for both transient tests and pressure-history data, it is time-consuming and subjective. A second technique uses regression analysis to replace the trial-and-error procedure with a systematic search that can be programmed for a digital computer. Use of regression analysis in reservoir description was proposed recently by Jacquard and Jain.1 They divided the reservoir into a number of homogeneous blocks whose properties are varied until a least-squares fit is obtained between observed and calculated pressures. However, they did not consider their technique to be operational, mainly because of ".. .(I) the lack of experience in using the method .. . notably for the improvement of convergence; and (2) limitations imposed by the insufficiency of available computers". 1 While the analysis presented in this paper applies the same general principle used by Jacquard and Jain, the specific method is significantly different. Some differences are (1) the regression problem is solved in a different way which requires less computer time in most cases; (2) a stepwise solution, in which the detail in the reservoir description is increased from step to step, is used to improve convergence; and (3) the reliability of the estimated reservoir .properties.. as measured by their standard deviation and correlation coefficient, is estimated&apos;

Jan 1, 1967

By William Hurst

THE content of this paper is a presentation of the diffusivity theory for the calculation of the water drive on an oil reservoir in which b the history of reservoir pressure with time are the essential parameters for the determination of the rate and cumulative water encroachment into a field. The paper is divided into two parts-the main portion and appendix. The main body is essentially the application of the principles underlined here to actual field data. It consists of the work plots of the radial-flow case, and includes a discussion of an illustrated problem for which the water-drive calculations are treated in conjunction with the volumetric-balance equation. The appendix is a mathematical treatment of the linear, radial, and spherical cases of water influx into a reservoir.

Jan 1, 1942

By Jonathan S. Jackson, Bayne B. McMillan, W. Joseph Schlitt

Various dump leach models have been developed by Kennecott, and these are reviewed with an eye toward production forecasting. Some of the models have been bated on first principles, utilizing the chemistry and physics of dump leaching. While providing considerable insight into the leaching process, these have proved to be too cumbersome for use in estimating production. Other models have been based on a declining leach rate for a single block of waste. These permit good short-term projections of solution grades and production, but are inflexible with regard to changes in mining parameters because the trends are based only on historical data. Therefore, a simple and flexible computer model has been developed to aid in leach production forecasting and to provide a tool for assessing the impact of different mining plans on leaching. This program, LEACH, is based on annualized blocks of waste; input parameters are described and examples of its use are given.

Jan 1, 1980

By Y. Takahashi, I. Iwasaki, S. Tanabe

Supported by the vigorous capital investment of the heavy and chemical industries and by the ever-increasing demand for durable consumer goods in the past decade, Japan has now emerged as the world&apos;s third largest steel producer, surpassed only by the United States and the Soviet Union. In 1968, the crude steel production is expected to exceed 50 million tons; the per capita steel consumption at that time will reach 886 lb, approaching the level of Western Europe. Characteristics of the Japanese steel industry is the high dependence of raw materials on overseas sources. Before World War II the industry relied on North China and Manchuria for coking coal, and on middle China, Hainan Island, the Philippines and the Malayan Peninsula for iron ores. After the war, the major sources of iron ores were shifted to the Philippines and the Malayan Peninsula, supplemented by shipments from the United States, Canada, India and Goa. The United States, in addition, became the primary source of coking coal.

Jan 1, 1967

By L. R. Gremillion, G. H. McClellan

Chemical and mineralogical data on 25 apatitic phosphate ores of diverse origins from commerical deposits around the world were widely variable. From 14 to 18 chemical constituents of each sample were determined, and each sample contained four to ten mineral phases. Altogether there were 34 different mineral phases, many of which occurred in only one sample. Samples contained varieties of francolites, fluorapatites, and mixed hydroxyfluorapatites. The apatite compositions calculated from chemical data showed that certain types of substitutions were characteristic of different apatite varieties, but every variety had some degree of substitution of (CO3)2- for (PO4)3-, and the P205 contents of the apatites ranged from 35.1 %for a North Carolina apatite to 41.9% for a Missouri apatite. In a concentrate with a grade of 32% P2O5, the North Carolina sample should contain about 8.7% gangue and the Missouri sample about 23.7% gangue. To optimize the digestion process of a phosphate ore, it is necessary to consider the dissolution behaviors of different mineral phases during acidulation and their possible effects on chemical properties of a fertilizer intermediate. In the production of wet-process acids or superphosphates, acidulation of certain minerals may cause foaming and formation of sludge, filtration, corrosion, and handling problems.

Jan 1, 1982

By Brahm Prakash, R. Schuhmann

Chemical conditions for flotation and nonflotation of cassiterite and fluorite with oleic acid as collector and with alizarin dyes as modifying agents were studied by means of small-scale, vacuum-flotation tests. Artificial cassiterite was prepared for these tests by high-temperature methods, especially by crystallization from borax melts.

Jan 1, 1950

By John Suman

DURING the past few years the taking of cores in drilling with rotary equipment has been perfected to a remarkable degree in the Gulf Coast fields of Texas and Louisiana. Taking of cores is becoming quite a common thing, especially in the newer fields, and drillers are becoming expert in this work. The writer has seen cores 5 to 8 ft. long taken with great ease in wells as deep as 4500 ft. Coring is doing much to remove the prejudice which so many petroleum engineers seem to have against .the use of rotary drilling equipment for exploratory work. Some operators .are now claiming that when used with a reasonable amount of coring the rotary system is even more satis-factory than cable tools for exploring in certain territory. A case has recently been pointed out in the South Electra field of North Texas, where producing oil sands, passed over by cable-tool drillers, are being brought in with rotary equipment. It seems that in this particular territory the sands are rather thin. Cable-tool drilling was carried on for the most part in a wet hole and the red mud encountered in drilling caved into the hole very badly, so that the cuttings showed mostly red mud and the driller, thinking that the sand did not amount to anything, carried his water string through the sand. The later .operators, drilling into the sand with rotary equipment and coring it, found that it was well worth testing.

Jan 10, 1922

By Magnus Troilius

SINCE the discussion on steel rails in America has forcibly drawn attention to the value of chemical analysis, if not as a necessary stipulation, at least as a guide to control the usual mechanical tests, some doubt has been thrown upon the accuracy of the analytical results obtained by different chemists. To any one having the least acquaintance with chemistry, it is quite clear that if exactly similar results are to be obtained from the same borings of steel, exactly the same methods must be used by the different analysts. Hence the necessity (if complications are to be avoided) of establishing what I may call standard or normal methods, to be used both by the inspectors and by the chemists at the works. Remembering that the application of chemistry to steelrail inspection is yet in its infancy, it is of great importance to possess a perfect acquaintance with the best methods in use. Being myself a grateful pupil of Professor Eggertz, of the School of Mines in Sweden, it occurred to me, two years ago, that I could not do better than start a laboratory of my own, and engage one of his pupils, Mr. Troilius, for the purpose of analyzing the steel borings from mechanically-tested rails, so that I might thus obtain without delay thoroughly accurate determinations. Moreover, in order to carry on the operations in perfect accordance with the methods used at the steel works in England and Germany, where I had to control the manufacture, I deemed it desirable to allow Mr. Troilius to go through a course of training at these works; and I gladly seize this opportunity of expressing my grateful acknowledgments to several works in England and in Germany for affording every facility for such an exchange of information as mas found necessary in arriving at the best analytical methods to be used.

Jan 1, 1882

By R. C. Gifkins, A. Gittins

A. Gittins and R. C. Gifkins (University of Mel-houvne)— Evidence from somewhat similar experiments to those described in this paper has led us to the conclusion that possibility 2) of the four listed on p. 319 is a description of what happens in grain boundary sliding. That is, sliding is limited by accommodation deformation, it being necessary to the Continuance of sliding that this accommodation should take place. An example of such accommodation, though probably not the most important, is fold formation at triple points. The evidence and arguments for this point of view are set out in Refs. 14 to 16. In particular, an experiment with a lead bicrys-tall5 seems to support point 2) rather than 3). In creep of this specimen it was found that at least 90 pct of the extension of a zone 0.3 mm wide at the boundary was supplied by sliding at the boundary. The sliding was localized in a region at the boundary very much smaller than 0.3 mm, in fact, in a region too narrow to resolve optically. In poly crystalline Specimens&apos; there appears to be a surface effect, as found by Rachinger," but it appears that this may not manifest itself at low strains. "Low strains" means <10 pct for a Pb-TI alloy, <2.5 pct for magnesium or "Magnox" A12 alloy, or <40 pct for a 0 brass. Up to this extension the sliding, measured by the mean vertical step at boundaries, is proportional to extension. We are able to say this with some confidence, since the error bars on our points are statistically derived. Our results would lead us to think that the error bars on other work, including that of Mullendore and Grant, are much too large at low strains to show this

Jan 1, 1963

By G. J. Heuer, J. N. Dew, G. C. Clark

The effect on well behavior of partial permeability barriers, changes in producing rates and well spacings have been calculated through use of a radial, unsteady-state, two-phase-flow mathematical model. This model allows for variations in permeabilities and porosities with distance from the wellbore. The numerical methods necessary to solve the problem require use of a highspeed digital computer, in this case an IBM 704. In each instance, pressure and saturation gradients, gas-oil ratios and recoveries around a well producing by solution-gas drive have been calculated as a function of time and distance from the wellbore. Comparisons are made to show the effect of changes in producing rate and of varying permeability near the wellbore and out in the formation on the production and pressure history of the well. The effect of different well spacings on producing rate and ultimate recovery is considered. Although the mathematical description of the reservoir is simplified in comparison to an actual reservoir, the results do give some insight into the difficult problem of spacing and proration in a heterogeneous solution-gas-drive reservoir. Results show that for the cases considered spacing has little effect on ultimate recovery and that permeability barriers removed from the well decrease producing rate for a period of time but have only a small effect on ultimate production. INTRODUCTION The effect of spacing and producing rate on the production characteristics and ultimate recovery of a well producing by the solution-gas-drive mechanism have been topics of interest to the oil industry for many years and the subject of many hearings before state regulatory bodies. The problem is very complicated because of the difficulty of simulating in the laboratory a reservoir producing by the solution-gas-drive mechanism under anything like normal field conditions. This paper gives the initial results of a study aimed at determining the effect of these factors on production from reservoirs simulated by a mathematical model. Two-phase, unsteady-state equations are used to calculate pressures, saturations, and rates of oil and gas flow as a function of time and distance from the wellbore. The model is radial, and reservoir properties may be varied with distance from the wellbore. A decrease in permeability at a given distance results in a low-permeability ring concentric with the wellbore through which all the fluids from more distant portions of the reservoir must flow. The current mathematical model allows for variation of permeability, porosity and saturations as a function of distance from the well. Any desired drainage radius for the well may be selected. Drainage radii of 745 and 1,053 ft, which correspond to 40- and 80-acre spacing, were chosen for the calculations which follow. A large amount of the input data has been held constant. No investigation was made into the effect of changes in fluid properties and relative permeability characteristics on oil and gas production behavior. Fluid properties and relative permeabilities are essentially those of the White Mesa portion of the Greater Aneth area in southeastern Utah. A recently concluded hearing before the Utah Oil and Gas Conservation Commission to determine spacing for the field aroused interest in the possible effect of permeability constrictions located some distance from the well on production and recovery. This interest stimulated the present study. In this paper, no attempt has been made to simulate any field production characteristics exactly. Only the solution-gas-drive mechanism has been investigated, and production by liquid expansion has not been considered. This investigation is exploratory in nature but does give some insight into the problems of spacing and proration in a solution-gas-drive field having permeability variations. THE MATHEMATICAL MODEL The mathematical model is similar to that proposed by West, Garvin and Sheldon.&apos; Approximately the same techniques have been used in arriving at a solution. The equations are nonlinear, partial differential equations which have been known for some time. The particular equations used for this study neglect the effects of capillary pressure and gravitational forces. The advent of modern digital computing equipment has made their solution practical. Basically, the method solves for pressure, saturations, and oil and gas flow rates as a function of distance and time. In our model, distance to the

By Bruce E. Grant, Thomas Jancic, Lawrence G. Dykers, Frank Buchella

Principal factors influencing equipment selection can be grouped into five basic categories: tonnage requirements, ore and waste; topography and property line considerations; ore control requirements; physical characteristics of ore and waste; and climatic considerations. Loading, transporting and ground preparation equipment are largely determined by tonnage requirements. Large size equipment is appropriate for a production of about six million tpm, medium size for three million tons and small size for one million tons or less.

Jan 12, 1973

By H. M. Day

THE constitution of the system silver-mercury has attracted the attention of many investigators during the last two decades, but since their results are for the most part in poor agreement, there is little need for a review of their individual contributions. It remained for the very careful thermal and microscopic investigation of Murphy1 in 1931 to give the constitutional diagram in its present and unquestioned form, which is shown in Fig. 1. He devised methods for taking cooling curves on alloys under high pressures and for the microscopic observation of alloys which contained liquid mercury as a structural constituent at ordinary temperatures. The compositions of the intermediate phases were con-firmed and supplemented through X-ray analyses by Preston and Stenbeck.3 According to Murphy, at 276° C. silver is able to dissolve 44 to 45 weight per cent of mercury, which may increase at lower tempera-tures to about 50 per cent. Preston concluded that the saturation boundary occurred at 46 ± 2 per cent at 100° C. From the values reported in the literature, these are the only ones that may be accepted as lying even in the right region.

Jan 1, 1938

By Robert H. Hafner, Irvin R. Kramer, Stewart L. Toleman

IN his paper on the calculation of hardenability from chemical composition, Grossmann1 discussed the effect of most of the alloying elements used commercially. The purpose of the work reported in this paper was to determine the effect of several other elements on hardenability-arsenic, antimony, beryllium, cobalt, columbium, germanium, tellurium, tin, aluminum, and titanium-and to extend the range of composition of some of the elements studied by , Grossmann-chromium, copper, manganese, molybdenum, nickel and silicon. EXPERIMENTAL METHODS To determine the effect on hardenability, suitable amounts of the alloying elements were added to experimental heats and the hardenability determined by means of end-quenched hardenability specimens. The steels were melted in a high-frequency induction furnace with a basic crucible, using ingot iron as a base for some of the heats and S.A.E. 1015 for others. The alloying additions were made as ferroalloys or as metal, depending on the &apos; alloying element. Hundred-pound heats were split and poured into square, tapered, cast-iron ingot molds with hot tops. Aluminum was not used as a deoxidizer in most of the heats. The ingots were homogenized for 12 hr. at 1260°C. (2300°F.) , and forged into rounds of 1 ½ in. diameter. These bars were normalized twice from 840°C. (1550°F.) before machining into Jominy bars. The composition of the steels was deter- [ ] mined in most cases by samples taken from the end-quench hardenability specimen. As suggested by crafts,2acid-soluble

Jan 1, 1943