Search Documents

By W. F. Boericke

INTRODUCTION THE Wisconsin zinc district, or the Upper Mississippi lead. and zinc district as it is also termed, lies in the southwestern corner of Wisconsin, and embraces adjacent portions of Illinois and Iowa. It includes Iowa, Grant, and Lafayette counties in Wisconsin, and Jo Davies county in Illinois. In Iowa, Dubuque formerly produced considerable lead, but there has been little mining there in recent years. The map, Fig. 1, shows the entire district, with roads, railways, streams, and the various towns, or "camps," around Which the mines. are clustered. The hatchwork indicates the areas iii which lead and zinc have been mined. The district is about 60 mi. (96 km.) north and south and about 40 mi. (64 km.) east and west. Not all of the territory is mineral bearing, and there are considerable areas that are believed to be barren. The grouping of the mines is patchy and irregular, though certain broad zones of mineralization extend almost the full width of the district, as from Mineral Point west through Mifflin and Livingston, and from Shullsburg west through New Diggings and Hazel Green. It is worth noting that the best mines of the district have, to date, been found within 10 mi. east or west of the fourth principal meridian line, thus lying within a long, narrow, north-and-south belt extending the length of the district. In a field as large as the Wisconsin, which has only within com-paratively recent time been worked intensively for zinc, the. chances are good for, opening new and important orebodies in parts of the district not yet, or insufficiently, prospected. However, the prospecting has been most successful around, or adjacent to, the old lead diggings of nearly a century ago, and the camps that were well known then are still centers of activity. In their order of importance they are: New Diggings, Benton, Mifflin-Livingston, Galena, Linden, Hazel Green, Shullsburg, and Highland.

Jan 8, 1919

By John V. Beall

The mining industry of Japan is not very large, but it is very old. Some of the mines have 1000 years of history. At Nara, the capitol 1300 years ago, the great Buddha of bronze that was cast at that time was of metal mined from several localities in Japan including the Akenobe-Ikuno district, one of the present Mitsubishi properties. Methods of smelting copper and iron, it is believed, came from China via Korea. A characteristic of the Japanese mining industry today is one of buying abroad and treating at home, a variety of ores of different compositions. All in all, Japan's mineral deposits under its own flag are inadequate for its great industrial strengths.

Jan 5, 1969

By F. E. Gregory

MINING methods and customs in many districts of England are to this day strangely bound about by the records and traditions of the past. In some mining fields this is more apparent than in others, yet it is everywhere in evidence, for Cornwall with her mines under the sea, Wales with her famous quartzites, and Derbyshire with her remarkable cavern deposits, are all tinctured with quaint customs that have come out of the almost forgotten past. Here, modernism has never replaced tradition, and many of the laws are woven of the woof and warp of ancient custom. Indeed, these things exist because they have come to be part and parcel of the civil laws. And these laws are observed with meticulous care and accorded all the reverence due their venerable age. All activities pertaining to the mining of metals are hedged around by curious and ofttimes clumsy laws, each minute and trivial detail being covered by the civil code, and each petty law enforced by an ofttimes pompous official.

Jan 1, 1933

R. G. BROWN, Bodie, Cal.: Mr. Rickard's paper, with its valuable illustrations, brings into fresh clearness the game of hide-and-seek which the miner must play with his ore-deposit; but, more than this, it goes far towards classifying those perplexing idiosyncrasies which, while unclassified, constitute a labyrinth almost without clue. Probably every engineer can add to the list by the mention of at least one fresh detail from his own experience, and I for one would like to comment on two of Mr. Rickard's divisions. To what he has written about " walls within walls" and " walls without walls," the accompanying Figs. 1 and 2 may be appropriate, the more so as they represent conditions obtaining in a part of the Butte copper-belt more typical of the copper-veins as a whole than the Gagnon, which, in some respects the most interesting mine in the camp, stands almost alone in many particulars. (See nuns., xvi., 62.) Fig. 1 was sketched in January, 1895, in the stopes above the 700-foot level of the Colusa-Parrot mine, east of the Parrot and southwest. of the Anaconda. The stope, the commercial foot-wall of which is shown at A, was 30 feet wide at this section, the pay-ore being massive chalcocite, jumbled with bornite, pyrite, quartz and thoroughly broken-down granite. A and At are inch-thick seams of black talc; B, B' and B" are also talc, possibly 1/8-inch thick. In the plane of the section the "banded quartz " and " quartz and pyrite " were both of too low grade for extraction, but 5 feet back along the stope had been of fair value. The granite with quartz and bornite between Bt and A' was pay-ore, but that to the right of B" was not. In both cases the ferro-magnesian minerals had been removed, leaving, where not obscured by ore, faint, dark patches. Between A'

Jan 1, 1897

By Orville R. Lyons, A. C. Richardson

F. X. Ferney—We are pleased that this paper was presented at this meeting and thank Mr. Richardson and Mr. Lyons for their effort and work in preparing it. We agree with the authors that it was unfortunate that more comprehensive data were not available when the paper was prepared, this being particularly true since we had no knowledge that the paper was being written and could not make available data which were in our process files. Further, it is our opinion that because the data are not sufficiently comprehensive the results which are presented are erratic and will lead to false conclusions. As we see it, there are three Specific reasons why the data which are presented cannot be considered accurate. 1. The preparation plant was not at equilibrium while the samples were being taken. This is indicated by the fact that the percent of solids in the circulating water varied from 3.9 pct to 10.7 pct during the period when the plant was sampled. 2. We do not believe that the samples of Bird feed which were taken were representative and could indicatc the true feed to the filter. Evidence of this is shown in the data where the dewatered product leaving the centrifuge contains more coarse material than the feed to it, that is, material which is +6-mesh in size. 3. We question if the data concerning screen analysis in the fine sizes is accurate and would conclude (from the data) that these tests were made by a dry-screen method. We have found that wet screening is always necessary to obtain a true picture of the quantity of —200-mesh fines which is present. The test work described in the Lyons-Richardson paper was conducted some time ago and the tests were carried on during a period when the preparation plant had not ironed out all of their start-up problems. Since that time most of these problems have been corrected and now this is a smooth running, well-operated prep-

Jan 1, 1951

By Orville R. Lyons, A. C. Richardson

F. X. Ferney—We are pleased that this paper was presented at this meeting and thank Mr. Richardson and Mr. Lyons for their effort and work in preparing it. We agree with the authors that it was unfortunate that more comprehensive data were not available when the paper was prepared, this being particularly true since we had no knowledge that the paper was being written and could not make available data which were in our process files. Further, it is our opinion that because the data are not sufficiently comprehensive the results which are presented are erratic and will lead to false conclusions. As we see it, there are three Specific reasons why the data which are presented cannot be considered accurate. 1. The preparation plant was not at equilibrium while the samples were being taken. This is indicated by the fact that the percent of solids in the circulating water varied from 3.9 pct to 10.7 pct during the period when the plant was sampled. 2. We do not believe that the samples of Bird feed which were taken were representative and could indicatc the true feed to the filter. Evidence of this is shown in the data where the dewatered product leaving the centrifuge contains more coarse material than the feed to it, that is, material which is +6-mesh in size. 3. We question if the data concerning screen analysis in the fine sizes is accurate and would conclude (from the data) that these tests were made by a dry-screen method. We have found that wet screening is always necessary to obtain a true picture of the quantity of —200-mesh fines which is present. The test work described in the Lyons-Richardson paper was conducted some time ago and the tests were carried on during a period when the preparation plant had not ironed out all of their start-up problems. Since that time most of these problems have been corrected and now this is a smooth running, well-operated prep-

Jan 1, 1951

By S. R. Dunbas, D. C. Jillson, E. A. Anderson

THE present work was undertaken to furnish information, lacking in the literature, on the deformation mechanisms active in pure titanium at room temperature. Since it was started, Rosi, Dube, and Alexander' have indicated that slip can occur in coarse-grained (2 to 6 mm diameter) titanium on the {1010} and {1011} planes and twinning can take place on the {1072}, (1122) and (1151) planes. Liu and Steinberg,' working with titanium flakes produced by fused salt electrolysis, found evidence of twinning on the {1032$, {1121), {1122}, (1123}, and (1154) planes. The crystals used in the present work were substantially longer (up to nearly 2 in. in length) and possibly purer. Production of Large Crystals It was the purpose of this part of the work to provide single crystal or large grain specimens for use in the deformation studies rather than to study the mechanism of crystal growth. Accordingly, all further exploratory studies on methods were abandoned when it was found that cold-rolled bars sealed in vacuo in individual Vycor tubes and given three or more cycles of 4 hr at 1200°C and three to five days at 850°C, gave large grains. Eighteen specimens about 0.2 in. square x 2 in. long yielded 33 useful grains, ranging from Va in. to nearly 2 in. in length, with an agreeably wide range of orientations, Fig. l. The 0.25 in. thick strip from which the starting specimens were cut had been reduced 67 pct on 18 in. diameter rolls from a scalped, hot-forged (959" to 1000°C), arc-melted, iodide titanium ingot. Thc bar was at room temperature, but the rolls were at 200°C. Reductions of about 0.03 in. per pass were used. The bar was cut into four segments, each of which was rolled in a somewhat different manner. No effect on the growth of large grains was noted. The composition of the titanium, determined on turnings from the ingot scalping operations, is given in Table I. The Rockwell A hardness of the ingot was 26. The standard starting specimens, about 1/4x1/4x2 in., were milled on all four sides, hand polished on 280 and 400 mesh emery papers, etched for 3 min in a 50 HF-50 glycerine solution, rinsed, and dried in alcohol and ether just before sealing them in Vycor tubes. The average specimen weight was 7.5 g, and the tube volume was 6.5 cc. A vacuum of less than 1 micron pressure was applied. The specimen tubes were placed in an evacuated Inconel muffle to minimize the danger of collapse of the glass tubes at temperature. In practice the specimens were first heated to 1200 °C for 4 hr and then transferred fairly quickly to an 850°C furnace where they were held for three to five days. This cycle was repeated at least three times before the specimens were cooled, removed from the tubes, lightly polished and etched on one surface for examinstion. Those in which large grains had not developed were resealed in Vycor and returned to the cycling. Satisfactory specimens (about one out of every four cycled) were polished with emery paper on all four side;, then metallographically polished using ctchinz between wheels to remove distorted metal and, finally, given a very light etch to reveal the grain boundaries. This was necessary because the surface was roughened by the sublimation of titanium under high temperature vacuum conditions. Specimens were identified by TiXl numbers using supplementary letters to designate specific grains.

Jan 1, 1954

By C. R. Kuzell

The Editor desires to call attention to the charts in the paper of the above title which were published in the August Bulletin on pages 2190 and 2191. It was impracticable to include in the Bulletin. charts of sufficient size to be used as working diagrams for the direct determination of operating values, but the Institute is prepared to furnish copies of these charts on a large-size scale, at a moderate cost, to those who desire to have them for this purpose. CORRECTIONS Page 2185, line 3. For "is accessory apparatus" read "in accessory. apparatus." Page 2188. Substitute for lines 11 and 12: Nitrogen, oxygen, carbon monoxide, Cp = 6.50 + 0.0010T Hydrogen, Cp = 6.50 + 0.0009T

Jan 9, 1914

By Herbert Haas

GEORGE W. HAWKINS, Tucson, Ariz. (communication to the Secretary*).-The paper by Mr. Haas will no doubt be followed with considerable interest, as it covers the power-plant problem in quite a comprehensive way, including not only the usual operating costs but also the fixed charges on the investment, and for load factors ranging all the way from 25 to 100 per cent. and fuel oil ranging from $1.25 to $2 per barrel. The very fact, however, that his paper does cover such a wide range of conditions, makes it the more imperative that any conclusion drawn from his analysis be very carefully considered for any specific case, for in making such analysis the type of prime mover and size must be selected for some one condition which might not be the proper selection had some other condition been assumed as the basic one, resulting in an unfavorable comparison under all conditions except that condition assumed. From the reasons given by the author for his selection of the large turbine units, it is evident he had in mind very high load factors, ranging

Jan 12, 1916

The co-operation of the members of the Institute is earnestly sought by the Committee on Nominations, recently appointed by the Board of Directors, in its work of formulating a ticket for officers and places falling vacant in the Board of Directors in February, 1916. The Committee must present the official ticket of nominations to the Board of Directors at its October meeting. Members are, therefore, urged to send promptly their nominations for officers and Directors in order that the Committee may have an opportunity to give them full consideration. The officers to be elected at the annual meeting in February, 1916, are: One officer, known as Director and President. Two officers, known as Director and Vice-President. Five officers, known as Director. The officers of the Institute whose terms expire are as follows: President, William L. Saunders (not eligible for re-election). Past President, Charles F. Rand. Vice-Presidents, Thomas H. Leggett, District 0; Fred W. Denton, District 4.

Jan 9, 1915

By Graham Bright

Before the arrival of central-station power, all coal and metal mines generated their own power and, in many cases, these isolated power plants gave a fair continuity of service. In coal mines that produce considerable gas, it is essential that power be available at all times for operating the ventilating fan and the hoist, if the mine is of the shaft type. In the case of an isolated power plant, if trouble should develop with the fan the men can be hoisted quickly when the mine is of the shaft type. On the other hand, if trouble develops with the hoist, the fan can be kept in operation, and there will be no necessity of haste in getting the men from the mine. Now that central-station power is being used so extensively for mine service, the continuity of service with gaseous mines is very important. : Inherently, the central station is much more reliable than any isolated plant, but trouble may occur on the transmission lines which may prevent the transmission of power for a considerable time. : Some mines have kept their steam equipment intact and ready for operation in case the purchased power should fail. This is expensive procedure, for the boiler plant must be fired at all times so that the emergency power will be quickly available. In a number of instances, gasoline-engine driven generators have been installed to furnish emergency power for the service hoist. As most service hoists are of the alternating-current type, the generator of the gasoline-engine driven set is usually of the a.c. type and is arranged to drive the service hoist motor at full speed, or an extra motor that can be thrown into gear on either the main or service hoist and the hoist operated at a greatly reduced speed. This arrangement is used because it is difficult and expensive to obtain and install large gasoline-engine driven units. The author has recently developed a plan by which the main hoist and the fan can both be operated at reduced speeds, in case of loss of power from a central-station power system. In this plan a gasoline-engine

Jan 1, 1923

By Graham Bright

Before the arrival of central-station power, all coal and metal mines generated their own power and, in many cases, these isolated power plants gave a fair continuity of service. In coal mines that produce considerable gas, it is essential that power be available at all times for operating the ventilating fan and the hoist, if the mine is of the shaft type. In the case of an isolated power plant, if trouble should develop with the fan the men can be hoisted quickly when the mine is of the shaft type. On the other hand, if trouble develops with the hoist, the fan can be kept in operation, and there will be no necessity of haste in getting the men from the mine. Now that central-station power is being used so extensively for mine service, the continuity of service with gaseous mines is very important. : Inherently, the central station is much more reliable than any isolated plant, but trouble may occur on the transmission lines which may prevent the transmission of power for a considerable time. : Some mines have kept their steam equipment intact and ready for operation in case the purchased power should fail. This is expensive procedure, for the boiler plant must be fired at all times so that the emergency power will be quickly available. In a number of instances, gasoline-engine driven generators have been installed to furnish emergency power for the service hoist. As most service hoists are of the alternating-current type, the generator of the gasoline-engine driven set is usually of the a.c. type and is arranged to drive the service hoist motor at full speed, or an extra motor that can be thrown into gear on either the main or service hoist and the hoist operated at a greatly reduced speed. This arrangement is used because it is difficult and expensive to obtain and install large gasoline-engine driven units. The author has recently developed a plan by which the main hoist and the fan can both be operated at reduced speeds, in case of loss of power from a central-station power system. In this plan a gasoline-engine

Jan 1, 1923

By T. S. Mohibatsela, R. V. Ramani, C. V. Manula

The Mineral Engineering Department of The Pennsylvania State University has developed a suite of computer models for anthracite open pit mining (Fig. 1)1 Individual sub-systems have been developed to (a) interpolate geologic field data to obtain coal tonnages, waste volumes, and strip ratios; (b) simulate equipment performance on selected pit profiles to generate data required to choose coal and waste removal equipment; and (c) evaluate selected cost factors to determine either a rate of return for a specified selling price or vice-versa. This paper describes the application of two of these subsystems, namely, the Reserves Model (GEOL) and the Open Pit Materials Handling Simulator (OPMHS), and how these may be applied for the selection of equipment for a prime anthracite mining site.2

Jan 1, 1981

F. Lynwood Garrison, Philadelphia, Pa. (communication to the Secretary): I have been specially interested in Mr. Drake's valuable contribution to our knowledge of the Chinese coalareas, as I had occasion, about a year ago, to make a reconnoissance over some of the coal-fields in the Yangtse river valley. I noticed, as he appears to have done, certain peculiarities which may eventually prove to be characteristic of the Chinese coal-measures, at least in central and northern China. The most striking feature, perhaps, is the invariable proximity of the great granite masses to those coal-deposits which have an anthracite character. In common with all other anthracite areas elsewhere, the Chinese show evidences of profound stratigraphical disturbances. The sedimentary rocks are folded, faulted and dislocated in a manner similar to those of the Pennsylvania anthracite-regions. It would seem that the intrusive granite had much to do with converting the original bituminous into present anthracite. The action of the granite was probably direct as a conveyor of heat, and indirect as dynamic force in dislocating, overturning, and compressing the coal-measures. My stay in China was unfortunately cut short, so that I was unable to collect fossils, or to give this highly interesting and important subject more than passing attention. Cholnoky* and Richthofen are practically agreed that these granite eruptions took place during the Tertiary period—probably the Eocene. This profound tectonic movement has had a most important effect upon the geological conditions in central and northern China, and will be, I am sure, a potent factor in the economic development. Evidences of disturbances and metamorphism are very abundant in the anthracite-areas of the Yangtse valley. I noticed the coal in them, as did Mr. Drake in northern China, to be often flaky and " slickensided."

Jan 1, 1902

By James W. Neill

Discussion of the paper of H. 0. Hofman, presented at the Canal Zone meeting, November, 1910, and printed in Bulletin No. 42, June, 1910, pp. 473 to 497. JAMES W. NEILL, Pasadena, Cal. (communication to the Secretary *) :-Professor Hofman's paper brings the art up to . date. As I was one of the pioneers in this business, I beg to give the following incomplete data regarding my efforts in this line. In the year 1883, while I was in charge of the smelting-operations at Mine La Motte, Mo., there was at the concentrator an unusually large production of a middle product, locally called "iron," which carried considerable values in nickel and cobalt, and which it was desirable, for this reason, to treat by itself. The works could not spare a furnace for the purpose; and to handle this product I improvised a "roast-hearth " from an old " lead-hearth." This was a small cast-iron furnace of the usual construction, about 2 by 4 ft. in dimensions, with a hollow cast-iron back, through which the wind circulated before entering the tuyeres. I had a cast-iron grate made to fit this hearth, and placed it flush with the lip, or apron, and above the tuyeres. On this grate, which had round holes about 0.25 in. in diameter, and a total surface of about 20 by 40 in., I roasted the nickeliferous pyrite product; starting the fire with kindling, then adding charcoal, and then gradually feeding the sulphides with a shovel, so as to cover the fire, choke down blow-holes, and get an even bed. Blast at a pressure of 3 or 4 oz. was supplied by a fail-blower. When a cake of roasted material had formed, it was removed with a steel bar, or fork, to the lip of the furnace, and thence into a wheel-barrow.. The fine material which had remained unmelted, but very hot, on top of the cake would promptly ignite when the cake was broken up and removed. The fire would then be covered with fresh material and * Received Aug. 29, 1910.

Apr 1, 1911

For a nation whose mining industry has generally been floating through history in the shadows of major mining developments elsewhere in the world, Australia has in the decade of the Sixties made a convincing bid to be one of the world's great "store- houses" of minerals. In fact, at the rate things are developing Down Under and Out Back, what with professional prospecting teams crisscrossing the continent under the direction of professional exploration management, Australia may one day find itself as the world's greatest storehouse. Whereas Necessity may be the Mother of Invention, Consumption is surely the Mother of Exploration. At least this is true in Australia of today. First, the forecasted shortage of iron ore in the world led to the fabulous discoveries in the Pilbara district of Western Australia. Now, the demand for nickel has generated even more interest among mining companies in the vast, untapped potential of Australia.

Jan 10, 1968

By R. J. Marcotte, C. T. Eddy, R. J. Smith

THE objectives of the investigation herein reported were to determine: (I) the S-curves for certain selected cast steels, (2) whether or not the published S-curves for wrought steels are satisfactory for use on cast steels of similar composition, and (3) to prepare hardenability curves of the selected cast steels. In order to make the final comparisons between cast and wrought steel more completely tangible, it was deemed advisable not only to determine S-curves for the steels submitted in the cast condition but also to roll some of the cast-steel test bars and determine comparison S-curves on such wrought material. This procedure eliminates the composition variable and makes it possible to reveal the differences resulting from plastic deformation of the cast structure in addition to providing the comparison with published data on wrought steels. CAST STEELS The cast steels selected for the preparation of S-curves, or time-temperature transformation curves, were similar to S.A.E. series 1030, 2330, 4130 and 4330. Of these the 1030 was supplied by The Crucible Steel Casting Co., Cleveland, Ohio, and the other three by The Sawbrook Steel Castings Co., Lockland, Ohio. The steels were furnished in the as-cast condition. The manufacturers supplied the chemical analyses and the properties that could be obtained in the heat-treated condition-all of which is summarized in Table I. [ ] PROCEDURE The metallographic and dilatometric procedures and equipment were in general standard. The specific technique employed was described in a report of the Steel

Jan 1, 1945

By A. Lubinski, C. R. Stewart, K. A. Blenkarn

Storage porosity has been considered one of the important pore geometry characteristics of heterogeneous-porosity limestones. Storage pores are only containers for fluids, in contrast to flow channel pores which both contain fluids and provide continuity for fluid flow. The concept of another geometry characteristic, "poro-striction", is presented as a second pertinent variable in describing limestone pore space. In simple terms, poro-striction is a measure of the flow resistance between storage and flow channel pores. Alternating-flow core-testing theory provides flow relationships which can be used to divide the pore space of heterogeneous-porosity media into flow channel and storage pores and to measure the "porostriction" of the latter. Experimental application of this theory to naturally occurring heterogeneous limestones shows that "porostriction" and the ratio of storage to flow channel pores can be estimated. Porostriction and porosity ratio are microscopic characteristics which should influence oil-recovery efficiencies during certain types of displacement processes. A knowledge of pore geometry should be valuable in designing or selecting the most effective oil-recovery process for heterogeneous limestones containing storage porosity. INTRODUCTION The primary and secondary recovery of oil from limestone (carbonate) reservoirs has been and will continue to be a major source of the world's supply of petroleum. Oil recovery from this type of formation is strongly influenced by the size, shape and arrangement of the pore spaces which hold the formation fluids. Therefore, it is expected that better knowledge of pore geometry would lead to design of more effective recovery processes. The concept of storage and flow channel pores has been presented as an important characteristic of limestone porosity.1 In this concept, storage pores are only containers for fluids, whereas flow channel pores are those pores which both contain and transmit the fluids. The work reported herein involves the concept of an additional pore characteristic called "porostriction". This characteristic can be visualized as the flow resistance between the storage and flow channel pores. This resistance is an important pore geometry characteristic because it determines how easily gas and oil can replenish fluids removed from the flow channel pores. Fatt and co-workers at the U. of California have studied the effect of storage porosity and a factor similar to porostriction on transient-flow response of models of porous media during a pressure build-up or drawdown test.55 These models consisted of porous sandstone cores with artificially simulated storage pores. It is the purpose of this paper to describe tests which permit the storage porosity and porostriction of actual reservoir core samples to be estimated. The tests used for this purpose involved not transient tests but, rather, an alternating-flow technique in which pressure and flow are varied according to a sine-wave relationship. This technique may offer advantages over transient methods. THE POROSTRICTION CONCEPT Before discussing alternating-flow (A.F.) tests in core samples, it is necessary to define the porostriction parameter. For this purpose attention is focused upon an elemental volume v representative of a porous medium having both flow channel pores and restricted-access storage pores. For such an elemental volume, it is considered that the storage porosity is combined to form a single pore and that the access into the storage porosity may be represented by a single capillary tube connecting the single pore to the flow channels of the elemental volume. Let the radius of the capillary tube be designated as Rc and its length as L,. When fluid flows into or out of the pore, the following equation (Poiseuille's law) relates flow rate q to pressure drop p, and the physical characteristics of the tube and the fluid of viscosity jx.

By H. F. Korman, M. C. C. Mow, P. K. Dai

INTRODUCTION Detonations of high explosives in soil and rock have been used frequently in civil engineering applications. Of particular interest in recent years has been the development of test methods to simulate the desired blast and shock environments for the testing of protective structures. The United States Air Force, in particular, the Air Force Weapons Laboratory, in conjunction with the Defense Atomic Support Agency, has in recent years, developed special technology for simulation testing of protective structures in soil and rock media. Such a technology, although initially developed for military applications, is rapidly finding its way into civil applications. One of the major problems in the design of the simulation test is the correct prediction of ground motion induced by the detonation of high explosives. This paper presents a useful prediction method which is developed specifically for ground motion in rock that is induced by the detonation of a buried planar array of explosive columns (See Figure 1). The technique of simulating shock environment using such an array is called the Direct Induced High Explosive Simulation Tech- nique (DIHEST). Normally, each shot hole may contain canisters of ammonium nitrate positioned at various depths, or a slurry explosive with detonators positioned along its length (See Figure 1). The depth and width of the array, the spacing of shot holes, the spacing of detonators, the degree of containment, and the charge weight are the variables which govern the induced ground motion

Jan 1, 1971

By Ross Glanville

INTRODUCTION The Optimum Production Rate (OPR) is one of the most important parameters in the evaluation of a mineral deposit. The OPR can also be expressed as the Optimum Mine Life (OML) in years since the expected mine life is determined by dividing the OPR per year into the estimated ore reserves. Unfortunately, very little time and effort has been directed towards the determination of the OPR. Instead, "rules of thumb" are often applied to select a mine life without due consideration of the economic implications of such a selection. A "justification" for a particular production rate is often based on a pre-conceived arbitrary requirement for a mine life of 5, 10, or 15 years, for example. In this paper it is demonstrated that such arbitrary selections for high-grade/low-tonnage mines (such as many underground gold/silver deposits) often lead to sub-optimal results. In fact, an apparently uneconomic deposit at an arbitrary production rate may be economic at the OPR. Consequently, investment opportunities may be overlooked if one analyzes mine properties based on arbitrary production rates. This paper analyzes the interrelationships of variables such as production rates, capital and operating costs, cut-off grades, discount rates, metal prices, etc. The analysis shows that the OML for high-grade/low-tonnage deposits is often in the range of two to four years. Although such mine lives intuitively appear too short to many individuals, it should be noted that, in the past, much of the mining industry became familiar with the economics of large scale mining operations. The rules of thumb developed for such large scale operations should not be applied to high-grade/low-tonnage mines such as many of the underground gold deposits. DEFINITION OF OPTIMUM PRODUCTION RATE The OPR is selected on the basis of maximizing the net present value of the after-tax cash flows. However, as discussed later in this paper, the production rate selected for a particular mine may be somewhat higher or lower than the theoretical OPR as a result of other variables such as: 1) the probability or expectation of additional reserves being discovered 2) the likelihood of being able to custom mill nearby deposits owned by others 3) the configuration or attitude of the orebody, which may place upper limits on the production rate 4) the residual, or salvage values, of the mine/mill facilities COMPARISON BETWEEN DIFFERENT PRODUCTION RATES For an orebody with definite physical cutoffs*, or boundaries (such as faults or unconformities), the total ore reserves at different production rates may be identical. Consequently, for such an orebody, varying production rates result in differing mine lives. Although the metallurgical recoveries, the mine dilution, and other similar physical parameters may vary slightly at different production rates, the major differences are the capital costs and operating costs per ton. The ramifications of these differences are especially important at low production rates (up to approximately 1000 tons per day), but can also be significant at higher production rates.

Jan 1, 1985