Search Documents

By George B. Harrington

This paper is a brief description of the design and equipment of a new coal mine in southern Illinois, which has many features not common practice in shaft coal mining and which is laid out and equipped for such unusually large capacity that it promises soon to become one of the largest mining operations of its kind. Shaft sinking for the mine, New Orient, was commenced in May, 1921, by the Chicago, Wilmington & Franklin Coal Co. In October, 1924, the plant was practically completed and was producing over 6000 tons of coal per day. There is good prospect that within a few years, when the mine is fully developed and manned, the output will attain a daily rate of 12,000 tons. The coal seam at New Orient lies approximately horizontal, about 500 ft. below the surface, and may be said to run from 9 to 12 ft. in thickness. The tendency in Franklin County has been toward large mining units (5000 to 6000 tons per day) with great care being given to protection against fire and explosion hazards, and usually with quite elaborate surface plants permitting careful preparation of the coal into graded sizes comparable with those made in the anthracite region. The field is unionized, with uniform conditions of wages for various classes of work, hours, etc., and the Illinois mining laws are quite specific with regard to fireproofing and safety measures. These conditions make it difficult for any hut well-equipped and well-operated mines to meet the competition of the numerous fine properties of which this county can justly be proud. The coal company's property was already developed on the western side by the Orient mine—a much visited and written about operation (with which many of you are possibly familiar through the Department of Mines' film "The Story of Coal") which until recently held the 8-hr, production record with 8218 tons and usually ran quite consistently with production of slightly over 6000 tons per day. Experience at Orient wat naturally one of the greatest influences in determining the location and character of the New Orient.

Jan 1, 1925

By M. H. Shumate

Rope-type haulage has had many applications in the mining and allied industries. Records have indicated favorable results both from a standpoint of efficiency and investment. The Truax-Traer Coal Co. has used some variations of rope haulage at their mines and preparation plants. They have built a system which solves their particular problems, and have an investment which has indicated an annual savings in operating costs. Rope haulage, as applied to the mining industry, goes back many years for both underground and surface mining, or a combination of both. The Truax-Traer Coal Co. has used gravity retarding hoists as well as several variations of rope haulage, including electrical and combinations of both, but each was limited in its use and application by natural conditions and economies of the operation. Several systems of rope haulage equipment are offered by manufacturers today for handling railroad car movement on a limited or continuous basis. The portal and railroad loading facilities of Truax-Traer Coal Co.'s Burning Star Slope mine, located in Jackson County, Ill., were moved in 1960. The old location was abondoned, eliminating 3% miles of underground track haulage. The mine was converted to an all-belt system, and coal is loaded at a new raw coal plant and shipped by railroad cars to a central cleaning plant. The company wanted to operate the surface facilities as efficiently as possible, employing a minimum number of workers, using the latest type railroad car movers. The existing rope haulage facilities at several locations throughout the country were examined and considered for the Slope mine location. The application of each appeared favorable but lacked flexibility, and it was difficult to justify the capital investment. The company decided to investigate the possibility of building a system that would apply to their problem, and have an investment that could be amortized in a relatively short period. SPECIFICATIONS They employed the services of Allen and Garcia Co. of Chicago, Ill. Through combined efforts, a railroad car rope system was designed to specifications as shown in Fig. 1. The Falk Corp. of Milwaukee, Wis. built the hoist to the specifications as shown in Fig. 2. It has an all welded base and pedestals. The all welded drum is not grooved. A single helical gear was used in lieu of herring bone type. A Falk speed reducer, Unit 90Y3-A, is driven by a 25-hp 1800-rpm, 440-V ac type 'C' (high starting torque) drip-proof, Frame 324-U motor. The speed reducer shaft is equipped with a solenoid operated ac spring set shoe brake, operating on a 7-in. diam. brake wheel. The dolly car, shown in Fig. 3, was field constructed, using the trucks and frame of a railroad tank car. Truax-Traer did not alter the frame but added plates and anchors for hoist ropes and frames for 8.5 tons of concrete to be used as ballast on the car. The limit switch operating shoe was also installed and the car coupler latch mechanism overhauled. The hoist rope selected was 1% in. in diam., 6x37 improved plow steel extra flexible, right lay, regular lay, with independent wire rope core, and preformed. Wedge sockets were used to connect rope to the dolly car as shown in Fig. 4. The system employs two 30-in. and three 16-in. diam. sheaves. All are bronze bushed and equipped with grease fittings. Larger sheaves are used for directional change of hoist rope and the smaller ones as snub sheaves to correct fleet angle of rope as it approaches the hoist drum. The Trench lay cable, buried between the two tracks, is used for electrical distribution and controls between hoists and operator's cab. Foundations for the system required 187 cu yards of reinforced concrete using approximately 60 cu yd each at three locations. Four hoists are employed in the system, two for each track. A pair is interconnected electrically and when one operates, moving the cars, the tail hoist idles with brake released. The process is repeated for the reverse direction. A limit switch, mounted in the track near each end of the system, is tripped by the dolly car as it approaches the hoist. The limit switch controls movement in one direction only, protecting the dolly car and establishing positive con-

Jan 1, 1962

By ROBERT R. ABUOTT

(Cleveland Meeting, October, 1912.) THE practice of carbonizing steel for the purpose of case-hardening has assumed great commercial importance within the past, 10 years. Formerly, case-hardened steel was held in more or less contempt, since it. was considered a cheap substitute for tool-steel. This is no longer the case. The development of the motor-car industry, and coincidentally that of modern alloy-steels, has resulted in overcoming many difficulties formerly experienced in case-hardening. This result has been accomplished by increased knowledge regarding the analysis of the steel which would respond most readily to case-hardening, and by more careful methods of treatment of the carbonized steel. The ordinary method of carbonizing consists in packing the steel with the carbonizing-material in cast-iron boxes and placing them in a furnace at a temperature of from 1,500° to 1,900° F. for a time sufficient to give the required depth of cc case." The steel is then either quenched directly from the box, or is allowed to cool without unpacking, and finally given a single hardening-heat., or, for special work, two or three heats. During the year 1911, more than 100,000 tons of carbonizing-material was sold in the United States, at an average price of probably $55 per ton. More than 85 per cent. of this material consisted of granulated bone. Within the past four years, many manufactured compounds have been placed on the market, consisting largely of some form of carbon or carbonaceous material, with or without the addition of chemicals. Steel will absorb carbon placed in contact with it at the temperature of the atmosphere. The reaction is exceedingly slow, but. increases rapidly with increasing temperature. Below * Metallurgical Engineer, The Peerless Motor Car Co.

Dec 1, 1912

By A. G. Metcalfe

Observations at temperature are used to investigate the phase changes in alloys containing more than 50 pct Co and above 1000°C. The nonsuppressible transformations in cobalt above 1120°C and in the intermetallic compound Co2Cr3 are studied. The liquidus and solidus surfaces are determined. Insufficient data is obtained to complete the constitution diagram. A REVIEW of some of the earlier work on cobalt' and on the binary systems with chromium2-4 and with molybdenum,5 showed that one likely source of differences might be attributed to the presence of phases at high temperatures which could not be retained by quenching. Consequently, the decision was made that only methods of examination at temperature should be used in this work. The correctness of this decision was confirmed during the course of the work by the investigation of the martensitic nature of the transformation in cobalt- and by the decomposition of the high temperature form of the phase Co2Cr3 on quenching.' The use of high temperature methods, including dilatometry and thermal etching led to the postula-tion of the existence of a high temperature form of cobalt with a probable hexagonal close-packed structure, transforming from cubic cobalt over a range of temperature from 1119° to 1145°C.8 One of the important pieces of evidence for this transformation was that it was observed in alloys with chromium and molybdenum which were nonmagnetic at this temperature so that confusion with magnetostriction effects was impossible. These results were not reported in this earlier paper, so that the data given here supply further evidence for the existence of a second allotropic transformation in cobalt. High temperature observations are necessarily much slower in producing results than the examination of quenched specimens at room temperature by conventional means such as X-ray diffraction or microexamination. The investigation has only covered a limited part of the field, as a result, extending from the liquidus down to about 1050°C and from the cobalt corner up to 50 pct alloying elements. The differences between the various reported diagrams for the constitution of the Co-Mo and Co-Cr systems have already been mentioned. The best available diagram in the first system is due to Sykes and Graff' which is shown in Fig. 1. Fig. 2 shows the latest Co-Cr diagram due to Elsea, Westerman, and Manning.' A comparison reveals that these are incompatible because of the disagreement with regard to the number of allotropes of cobalt. Elsea, Westerman and Manning took their liquidus and solidus curves from Wever and Haschimoto.2 The temperature horizontal in the two-phase field beneath the eutectic was placed 35" to 39°C higher than in earlier work2,4 with a new interpretation of the nature of this transformation. This interpretation also required a peritectic horizontal at about 1470°C, which has been confirmed here for an alloy with 53 pct Cr. No investigation had been made of the ternary system until after this work had been terminated, when a section at 1200°C was published." In this work a ternary compound was found by the X-ray diffraction examination of quenched alloys. This compound contained less than 50 pct Co, and was thus outside the field investigated here. However, some reactions were found dilatometrically which could not be fitted on the diagram and are now believed

Jan 1, 1954

By L. G. Sprague

The fact that this latest and most modern of the Universal Atlas Cement Company's plants at Northampton, Pa., is the fifth to be built on these same properties, and their development has been coincidental with the development of the portland cement industry in the United States, makes it appropriate to sketch briefly the history of the successive steps. In 1889 the original Atlas Portland Cement Co. started its first plant at Coplay, Pa., which is just across the Lehigh River from the present operation. Here the first successful rotary kiln was operated. These kilns were 6 ft. in diameter and 60 ft. long; they used oil for fuel until 1895, when the company developed the first burner for pulverized coal. Shortly thereafter the Atlas company acquired property on the Northampton side of the river and built its plants Nos. 2, 3 and 4 within the following 10 years. During the same period the production of portland cement in the country was increasing rapidly; owing largely to the development of the rotary kiln and improved grinding machinery, which lowered the cost and improved the quality of cement. The general tendency has been to increase the length of the kiln and grind both raw material and finished product Liner. In 1930 the Atlas Portland Cement Co. and the Universal Portland Cement Co. united to form the Universal Atlas Cement Co., and the same policy of improving the product has been continued. Because of the large amount of research carried on by manufacturers and consumers, including government agencies, there is a demand for cement of different chemical and physical characteristics for different kinds of structures. Hence many engineers in recent years have been asking for cements of certain definite chemical analyses, which they think are best for their particular jobs. This has compelled the manufacturer to make several different types of cement by variations of chemical composition. These are generally made by adding silica, iron and lime to the standard mixture, which necessarily increases the cost of the product. Therefore the Universal Atlas Cement Co., in planning the modernization of its Northampton plant, gave this particular phase of the problem considerable study. Research and experimentation have developed the practicability of making a wide variety of differently proportioned raw materials for cement by a process of subtraction rather than by addition. With such process, it is possible to discard the undesirable aluminates and silicates from the ample supply of impure limestone available from the company's property rather than by adding high-grade limestone obtained from distant sources. This procedure requires mineral separation by centrifugal sedimentation and froth flotation. Since the chemical and mineral constituents of Lehigh Valley "cement rock," together with the methods of separating them, have been thoroughly described in published

Jan 1, 1948

By L. G. Sprague

The fact that this latest and most modern of the Universal Atlas Cement Company's plants at Northampton, Pa., is the fifth to be built on these same properties, and their development has been coincidental with the development of the portland cement industry in the United States, makes it appropriate to sketch briefly the history of the successive steps. In 1889 the original Atlas Portland Cement Co. started its first plant at Coplay, Pa., which is just across the Lehigh River from the present operation. Here the first successful rotary kiln was operated. These kilns were 6 ft. in diameter and 60 ft. long; they used oil for fuel until 1895, when the company developed the first burner for pulverized coal. Shortly thereafter the Atlas company acquired property on the Northampton side of the river and built its plants Nos. 2, 3 and 4 within the following 10 years. During the same period the production of portland cement in the country was increasing rapidly; owing largely to the development of the rotary kiln and improved grinding machinery, which lowered the cost and improved the quality of cement. The general tendency has been to increase the length of the kiln and grind both raw material and finished product Liner. In 1930 the Atlas Portland Cement Co. and the Universal Portland Cement Co. united to form the Universal Atlas Cement Co., and the same policy of improving the product has been continued. Because of the large amount of research carried on by manufacturers and consumers, including government agencies, there is a demand for cement of different chemical and physical characteristics for different kinds of structures. Hence many engineers in recent years have been asking for cements of certain definite chemical analyses, which they think are best for their particular jobs. This has compelled the manufacturer to make several different types of cement by variations of chemical composition. These are generally made by adding silica, iron and lime to the standard mixture, which necessarily increases the cost of the product. Therefore the Universal Atlas Cement Co., in planning the modernization of its Northampton plant, gave this particular phase of the problem considerable study. Research and experimentation have developed the practicability of making a wide variety of differently proportioned raw materials for cement by a process of subtraction rather than by addition. With such process, it is possible to discard the undesirable aluminates and silicates from the ample supply of impure limestone available from the company's property rather than by adding high-grade limestone obtained from distant sources. This procedure requires mineral separation by centrifugal sedimentation and froth flotation. Since the chemical and mineral constituents of Lehigh Valley "cement rock," together with the methods of separating them, have been thoroughly described in published

Jan 1, 1948

By V. F. STANLEY

THERE is not the slightest doubt that the present recoveries of valuable minerals by the Broken Hill mills could be improved, and that further machinery would be installed for the purpose if it could be assured that a high price of metals would be maintained; but concentration, like all other com¬mercial propositions, is a question of profit and loss, and no sensible metallurgist would carry out his work in such a manner as to obtain high recoveries at a financial loss to his company. There is a point in all concentration at which the added money obtained from the higher recovery of minerals is balanced by the extra cost of obtaining the last part of the recovery; a wise metallurgist will be content with his work before his working-expenditure reaches this point. To a casual observer, the work being done by the various Broken Hill mills is identically the same. A closer investigation will show that this is far from being the case, for it is a remarkable fact that, although the larger mines extend over a length of approximately only 2 miles, such a difference in the physical and chemical properties of the ores exists that, from the first reduction downwards, special treatment is necessary in each case, and hardly any two mills are identical in operation. The details of this paper refer directly- to the work of one . particular mill in Broken Hill, for the reason that the ore from each mine presents special difficulties and requires its own special treatment. I have selected the mill referred to because it has been constructed and modified under my supervision.

Sep 1, 1909

By L. G. Sprague

THE fact that this latest and most modern of the Universal Atlas Cement Company's plants at Northampton, Pa., is the fifth to be built on these same properties, and their development has been coincidental with the development of the portland cement industry in the United States, makes it appropriate to sketch briefly the history of the successive steps. In 1889 the original Atlas Portland Cement Co. started its first plant at Coplay, Pa., which is just across the Lehigh River from the present operation. Here the first successful rotary kiln was operated. These kilns were 6 ft. in diameter and 60 ft. long; they used oil for fuel until 1895, when the company developed the first burner for pulverized coal. Shortly thereafter the Atlas company acquired property on the Northampton side of the river and built its plants Nos. 2, 3 and 4 within the following 10 years. During the same period the production of portland cement in the country was increasing rapidly; owing largely to the development of the rotary kiln and improved grinding machinery, which lowered the cost and improved the quality of cement. The general tendency has been to increase the length of the kiln and grind both raw material and finished product finer. In 1930 the Atlas Portland Cement Co. and the Universal Portland Cement Co. united to form the Universal Atlas Cement Co., and the same policy of improving the product has been continued. Because of the large amount of research carried on by manufacturers and consumers, including government agencies, there is a demand for cement of different chemical and physical characteristics for different kinds of structures. Hence many engineers in recent years have been asking for cements of certain definite chemical analyses, which they think are best for their particular jobs. This has compelled the manufacturer to make several different types of cement by variations of chemical composition. These are generally made by adding silica, iron and lime to the standard mixture, which necessarily increases the cost of the product. Therefore the Universal Atlas Cement Co., in planning the modernization of its Northampton plant, gave this particular phase of the problem considerable study. Research and experimentation have developed the practicability of making a wide variety of differently proportioned raw materials for cement by a process of subtraction rather than by addition. With such process, it is possible to discard the undesirable aluminates and silicates from the ample supply of impure limestone available from the company's property rather than by adding high-grade limestone obtained from distant sources. This procedure requires mineral separation by centrifugal sedimentation and froth flotation. Since the chemical and mineral constituents of Lehigh Valley "cement rock," together with the methods of separating them, have been thoroughly described in published

Jan 1, 1943

By H. W. Gillett

MAINTENANCE of membership by the technical so¬cieties and the activity of these societies in spite of the adverse business situation have been noteworthy. This forcibly brings home the fact that industry recognizes that sound technical guidance is well worth its cost. The numerous difficulties and losses due to defects of various kinds arising from gas-metal reactions are now generally recognized and interest in these problems is widespread. The forthcoming A. I. M. E. round-table discussion of gas-metal problems will do much to clarify the situation and will permit us to assay our present knowledge and to suggest the proper direction for profitable future research. "The Age Hardening of Metal" was the title of the annual I. M. D. lecture delivered by Dr. Paul D. Merica. A critical review of the known facts relating to age-hardening phenomena was first given, followed by the presentation of a theory correlating the detailed observations which have been made regarding the mechanism of the hardening.

Jan 1, 1933

By F. B. Plummer

GEOLOGICAL engineering as applied to oil fields, or production geology as some prefer to designate the profession, is designed to fill in the border line between pure geology and pure petroleum engineering. Therefore the production geologist may, and frequently does, reach out to grasp much in both professions. Where once the oil geologist was content to pick samples out of a mud ditch and try to identify oil formations from the color or appearance of flakes of rock bailed out of a well, now he has to deal with graphic electrical logs obtained by intricate and highly technical electrical apparatus and to make exact determinations to the fraction of an inch of the depth and thickness of an oil sand 2 miles below the surface.

Jan 1, 1944

CRUSHING and concentration flow-sheets of western mills have become greatly simplified and more or less standardized of recent years with the introduction of modern grinding methods and flotation. Improvement has not stopped, however, and advancement is continually being made in crushing and milling practice. A case in point, where remarkable improvements in efficiency have resulted from comparatively minor changes in the flow-sheet, is in the New Cornelia mill of the Calumet and Arizona Mining Co. at Ajo, Ariz. This mill, completed in 1924 for the concentration ,of the sulfide ores of the New Cornelia mine, was originally designed for a 5000-ton capacity. Before recent changes and additions were made the five 1000-ton units were handling 6500 to 7000 tons per day, giving a flotation feed of approximately 14 per

Jan 1, 1930

By J. J. Calaman, D. H. Fleming

DURING 1950 the jet-piercing process was used commercially in the piercing of primary blast-holes in magnetic taconite at the preliminary taconite plant of .the Erie Mining Co., Aurora, Minn. The Erie Mining Co. purchased a jet-piercing machine and associated equipment in 1949, and the machine has been in operation since its installation in the summer of that year. An overall view of the pit with the JPM-1 jet-piercing machine in operation is shown in Fig. 1. During three months of 1949 and continuously since February 1950, production piercing took place under all pit conditions. By the end of October 1950, a total of 15,000 linear ft of hole had been pierced in an open pit handling an average of 1200 to 1800 tons of crude a day in one 8-hr shift. While it is recognized that this output does not approach the millions of tons a year planned for the developing Minnesota taconite projects, the machine as a unit has been operating under conditions probably more adverse than those that eventually will be encountered in the large operations. This pilot operation has permitted evaluation of the piercing problem in the full-scale taconite plant. This paper describes jet-piercing process funda- mentals, important features of the latest jet-piercing burners and machine, actual piercing results obtained, and new developments that give promise of materially increasing overall process efficiency. To produce the blasthole, jet-piercing utilizes thermal energy, as contrasted with the application of mechanical energy in churn drills and jackham-mers. The heart of the process may be termed a tailored flame produced by a rocket-type burner, thermodynamically similar in every respect to that of the giant rockets being developed for military purposes. The heat release in the combustion chamber of the burner is about 50x10' Btu per cu ft per hr as compared with 5x10' for most modern steam generators.* Combustion of liquid petroleum fuels (kerosine, diesel oil, or No. 2 fuel oil) with gaseous oxygen in the burner chamber at pressures of 100 to 200 psi results in temperatures of about 4300°F. Expansion of the hot combustion gases through divergent nozzles produces high-temperature supersonic jets having measured velocities of about 6000 fps. Impinging the flame jets on rock causes a thin surface layer to expand and break away from the base as a result of the thermally induced stresses. This spalling action is aided further in chert and quartzite by the 0.82 pct volume change resulting from the 6 to p quartz inversion at 1066"F.t The dynamic action of the jets whisks the spalled rock

Jan 1, 1952

By George C. Gibbons

ALMOST everyone in any of the five counties embracing the great East Texas field depends heavily upon oil for his living whether or not he actually owns a well or piece of royalty himself. Oil is a natural resource that, when utilized, spreads its benefits over a vast area and into many channels. Depending then almost entirely upon agriculture: what is now known as the East Texas oil field a decade ago had a scattered farming population. For many of its people, tomatoes and other vegetable crops coupled with the old southern stand-by of cotton, furnished an adequate living and a small cash surplus. Some farm families on the red hills, however, were not far re- moved from the sowbelly and black- eyed peas, or cornpone and potlikker, standard of living. Kilgore of that day, was a village of less than 850 per- sons. Longview, with just over 5000, apparently had reached the limit of its growth. Tyler was an overgrown farming town of around 17,000 persons, de- pending largely upon the agricultural income of Smith County and surrounding territory for which it was a trading center.

Jan 1, 1941

By Ralph M. Hunter

UNTIL recent years, maintenance of surface coal handling facilities was a relatively simple task. Equipment consisted principally of conveyors, screens and crushers of comparatively simple construction. Electrical equipment consisted of motors and starters, with little, if any, interlocking. In most cases failure of any component affected only the grades of coal loaded so that even a prolonged break-down did not affect mine operation materially. However, with the introduction of modern cleaning plants, the picture has changed. The equipment is much more complex and therefore more difficult to maintain. In many cases failure of any component of the plant prevents loading of coal. Even if provision is made to by-pass, the quality of coal loaded is lowered, affecting markets. In the case of plants designed to permit full seam mining, marketable coal cannot be loaded without operation of the cleaning plant. Under these conditions it is apparent that considerable thought and effort toward better maintenance are justified. In order to assure continuous, efficient and economical operation, maintenance should receive consideration, not only after the plant is in operation, but while it is being designed. It is hardly necessary to say that the designer should strive for sturdiness and wearing qualities. It is sometimes not realized, however, that even the best parts will sooner or later require replacement or repair. The designer should, therefore, give consideration to accessibility. Anyone who has had to do with cleaning plant maintenance is familiar with installations where several hours are required to get at a part that can be repaired or replaced in a few minutes, once it is accessible. As in most cases, experience is the best guide. The men who operate and maintain this equipment know the problems encountered. Whenever available, the opinions of these men should be sought and heeded. As an example, we might consider the refuse elevator on a Chance Cone. Our company is now operating three of these cones, the first of which was installed in 1941, and the latest in 2946. Exact records are not available, but well over 50 pct of delays charged to the Chance Cones have been caused by the refuse elevator. This elevator receives refuse from the cone and carries it to a point above the water level of the cone, discharging onto a dewatering and desanding screen. Since the elevator operates under water and necessarily has close clearances in the lower boot, it tends to jam on large pieces of refuse or tramp iron. The chain, buckets and boot are also subjected to the action of water, sand and refuse, which accelerate normal wear. In case of jamming or chain-breakage it is necessary to drain the elevator and the cone so that even a minor fault in the elevator causes a considerable loss of time for the cone. In our new plant, which will contain two Chance Cones, the refuse elevator has been eliminated. This was accomplished by raising the cone so that the refuse gates could discharge directly onto the dewater-

Jan 1, 1948

By Ralph M. Hunter

Until recent years, maintenance of surface coal handling facilities was a relatively simple task. Equipment consisted principally of conveyors, screens and crushers of comparatively simple construction. Electrical equipment consisted of motors and starters, with little, if any, interlocking. In most cases failure of any component affected only the grades of coal loaded so that even a prolonged breakdown did not affect mine operation materially. However, with the introduction of modern cleaning plants, the picture has changed. The equipment is much more complex and therefore more difficult to maintain. In many cases failure of any component of the plant prevents loading of coal. Even if provision is made to bypass, the quality of coal loaded is lowered, affecting markets. In the case of plants designed to permit full seam mining, marketable coal cannot be loaded without operation of the cleaning plant. Under these conditions it is apparent that considerable thought and effort toward better maintenance are justified. In order to assure continuous, efficient and economical operation, maintenance should receive consideration, not only after the plant is in operation, but while it is being designed. It is hardly necessary to say that the designer should strive for sturdi-ness and wearing qualities. It is sometimes not realized, however, that even the best parts will sooner or later require replacement or repair. The designer should, there- fore, give consideration to accessibility. Anyone who has had to do with cleaning plant maintenance is familiar with installations where several hours are required to get at a part that can be repaired or replaced in a few minutes, once it is accessible. As in most cases, experience is the best guide. The men who operate and maintain this equipment know the problems encountered. Whenever available, the opinions of these men should be sought and heeded. As an example, we might consider the refuse elevator on a Chance Cone. Our company is now operating three of these cones, the first of which was installed in 1941, and the latest in 1946. Exact records are not available, but well over 50 pct of delays charged to the Chance Cones have been caused by the refuse elevator. This elevator receives refuse from the cone and carries it to a point above the water level of the cone, discharging onto a dewatering and desanding screen. Since the elevator operates under water and necessarily has close clearances in the lower boot, it tends to jam on large pieces of refuse or tramp iron. The chain, buckets and boot are also subjected to the action of water, sand and refuse, which accelerate normal wear. In case of jamming or chain-breakage it is necessary to drain the elevator and the cone so that even a minor fault in the elevator causes a considerable loss of time for the cone. In our new plant, which will contain two Chance Cones, the refuse elevator has been eliminated. This was accomplished by raising the cone so that the refuse gates could discharge directly onto the dewater-

Jan 1, 1949

By W. H. C. SIMMONDS

The mining, metallurgical, and petroleum industries can be viewed as financial or as social institutions or both. The differences between these two conceptions of their businesses will influence their environmental 'and social actions. During the next 10-20 years western industry will be subject to a drop in the growth of a more highly educated labour force and to the emergence of holistic economics, new national goals, and a new ecological perspective. The profitability of the mining industry may therefore be influenced by the human side of its business to a greater degree. The increasing human, social, and environmental responsibilities can be discharged by improving the miner's equipment; by learning to look at situations through the eyes of all those involved; by developing common 'languages' which governments and the public can understand; and by mediating where feasible on the international scene.

Jan 1, 1978

By H. T. Shore, J. M. Schultz

A number of experimental rnethods—X-ray powder diffractometry, Laue photography, X-ray small-angle scattering, and transmission electron microscopy and dijfraction—have been utilized to examine the morphology associated with precipitation from the terminal, g, solid solution of a Zn-1 pct Cu alloy. A significant age hardening was observed in a 1 pct Cu alloy. X-ray and electron diffraction results showed that the structural inhomogeneities associated with the hardening were isotructural with the matrix. The average size and shape of the inhomogeneities were deduced from the electron microscopy and X-ray small-angle scattering. The preprecipitates are hexagonal platelets some 300? in diam. and some twelve unit cells thick. The orientation of the platelets was deduced from Laue photographs and electron diffraction. The platelet plane is (0001). When a large amount of pre-precipitation is present in a localized volume the new lattice is often disoriented by a rotation about (0001) of of the matrix. WhILE dilute Zn-Cu alloys have been commercially important for some 50 years, relatively very little is known metallographically about this material. The "Zilloys", zinc with about 1 wt pct Cu and sometimes a small addition of magnesium, are used to produce rolled zinc which is harder and stronger than that produced by other rollable zinc alloys.' According to the phase diagrams of the zinc-rich side of the Cu-Zn system, such dilute Zn-Cu alloys should age-harden;2-5 the solubility of copper in zinc, g-phase, at 424°C is 2.68 pct, while at 0°C it is only to 0.3 pct. However, the published literature on the aging of this system appears to be limited to a documentation of the contraction of 1, 2, and 3 pct Cu alloys aging at 95°c,6 and an attempt to measure changes in lattice parameters during aging.' In the latter work, no lattice parameter changes were detected, although a broadening of the highest-angle lines was detected and considerable diffuse scattering was observed. Micro-structural investigations have been limited to the latest stage of aging, wherein Widmanstatten precipitates are formed.3,47 These alloys are of interest for still another reason. The two most zinc-rich phases in the Cu-Zn system, 77 and E, are both hcp. Moreover, the change in a, between 17 and t for a 1 wt pct Cu alloy is onlv 3.64 -,~ct: the change in Co is 12.0 ict. It would be anticipated that precipitation in such a material might occur through metastable phases or G.P. zones with epitaxy along mutual 0001 planes. The goals of the present work are aimed at partially filling the void of knowledge concerning the early stages of precipitation from the g phase. In particular, we have attempted to document the magnitude of the age hardening of this system and to determine the size, shape, and orientation within the matrix of the elements of precipitation in an early stage of condensation. EXPERIMENTAL A) Specimen Preparation. Specimens were prepared In two somewhat different ways, one method being used for X-ray Laue and diffractometer measurements, optical microscopy, and Rockwell hardness measurements and the other used for electron microscopy and X-ray small-angle scattering. In the first case zinc and copper in the proper proportions to yield a 1 wt pct Cu alloy were melted together in a closed graphite crucible. Castings so made were free of apparent segregation or oxidation. The castings were then solution-annealed at 400°C for several days and then quenched in water to room temperature. Filings of portions of the specimens were made for use as X-ray powder diffractometry specimens. The electron microscope material was made as follows. Castings were made under vacuum with copper powder placed inside a hollow zinc cylinder to insure good contact of the materials. These 1 wt pct Cu pieces were then rolled to 0.1 mm with an intermediate anneal in vacuo. The rolled sheets so formed were then annealed for about 6 hr at 225°C. Finally the specimens were electropolished slowly until thin enough for transmission electron microscopy. The polishing is discussed in greater detail in the Results section. B) Measurements. X-ray measurements of three types were performed. A G.E. XRD-5 diffractometer was used to examine powders of the alloy for identification of second-phase material. A Kratky small-angle camera, also operating from a G.E. tube, was used to investigate the sizes of small precipitate particles. In both cases, nickel-filtered copper radiation was utilized. Finally, individual grains of the large-grained castings were examined in the back-reflection Laue geometry. Electron microscope studies were carried out with a J.E.O.L. Model 6A instrument. RESULTS A) Hardness Measurements. Hardness measurements performed at room temperature on the large-grained polycrystalline specimens showed a hardening which was essentially complete in 3 hr. Fig. 1 shows a typical plot of hardness vs aging time. The relative magnitude of the ultimate hardening varied from run to run between 150 and 200 pct of the value for the material immediately after quenching from the solution anneal. Most probably the variations reflect small changes in the time taken to remove the specimen from the vacuum furnace after the solution anneal.

Jan 1, 1969

By W. S. Row

This mine is operated at 4000 to 4500 tons daily through a single shaft, with one rock hoist and one senice hoist. Latest shaft construction is concrete with wooden dividers. Economics of drifters and air-leg drills are compared, as well as costs of shrinkage and sub-level stoping. Economy of large haulage equipment and underground crushing is shown. THE property of Kerr-Addison Gold Mines is located in the Larder Lake district of Ontario about 3 miles from the Quebec boundary on the highway between Kirkland Lake and Noranda. It is roughly 320 miles due north of Toronto and 365 miles north of Buffalo, N. Y. The property was staked in 1906 and after several development efforts finally came into continuous production at 500 tons per day in 1937. In 1939 the daily tonnage -was increased to 1200 and in 1941 to 2100 tons. At the end of the war, because of the shortage of labor, tonnage was down to 1100 tons per day, rising to 2200 in February 1947. A further plant expansion inaugurated in 1946 was completed by December 1948, bringing the capacity of the mine and mill to a production rate of 4000 tons per day. Current production, with 880 men employed, is 4400 tons per day. Changes in mining methods and equipment, required by the recently completed expansion program, have yielded interesting comparative results, some of which are described in this paper. Hoisting of ore and waste from the mine, as well as all service facilities for handling men and supplies underground, are provided for in a single vertical five-compartment shaft. Ore and waste are hoisted in 12½-ton skips in balance by a 14-ft diam hoist with drums 115 in. wide, grooved for 2?-in. wire ropes. This hoist, with a total rope pull of 85,000 lb, was designed to operate at a speed of 2600 ft per min to a depth of 4000 ft, hoisting 15 tons of ore in each skip. It is amplidyne-controlled and powered with dual drive dc motors of 2250-hp each, through flexible couplings to two pinion shafts, one on each side of the main gear. Each motor has a peak load rating of 4500-hp at point of greatest duty. Direct current power to the hoist motors is supplied from a motor generator set consisting of a 5000-hp synchronous motor driving two 1750-kw dc generators. The loading pockets used so far are at depths of 1500 and 2725 ft respectively. Consequently the present hoisting speed is 2000 ft per min and the skips capacity only 12½ tons. Now that the shaft has been deepened the new pockets at 3934 ft will be increasingly used so that the speed and the skip size will be increased up to original specifications as required. Some difficulty in meeting the required hoisting cycle is expected because of the shape of the skips. As now in use the cross-sectional dimensions of the inside of the skip are 4 ft 6 in. x 3 ft 8 in. To hold 121/2 tons, therefore, they are 14 ft 10 in. deep. Since the skips are the conventional overturning or Kim-berley type, considerable hoisting time is lost in retardation in entering the headframe dump and in acceleration when leaving. It is expected that to obtain the specified tonnage from this hoist when the skip size is increased to 15 tons it may be necessary to resort to bottom dump skips. This type of skip could reduce considerably the present excessive acceleration and retardation times. Analyses of the skip-hoisting operation are made monthly, and every effort is made to reduce controllable delays. For a nine-month period in 1951 such an analysis shows that the hoist was in operation 92.5 pct of the available time, which was allotted as shown in Table I. Overall hoisting costs, cage and skip, for the year 1951, averaged $0.168 per ton of ore milled. The mine is serviced entirely by means of a single cage, capacity 35 men or 15,700 lb, operating in con-

Jan 1, 1954

By L. R. Smith

BUTANE OPERATED drilling rigs are a recent innovation in the petroleum industry, so extensive data on their operation are not available. However, experience indicates that, within limitations, as much can he accomplished with butane as with steam, at a decided reduction .in expense of installation and cost of operation. Commercial butane is a liquid motor fuel similar to gasoline, but much more volatile, so that it has to be stored under pressure. At 10° F. it is liquid at atmospheric pressure, but at 100° it has a pressure of 70 lb. or more. As soon as the pressure is reduced, it turns to vapor and in that state is far more easily mixed with the air necessary for combustion. Butane occurs as a by-product in the absorption process of natural gasoline extraction from casing-head gas. The product has been used to some extent 10 raise the octane value of gasoline. However, because of its volatile nature, such admixture is stable only to a limited degree. Attempts also have been made to introduce the product in a gaseous form into oil- hearing formations in repressuring work. It has, however, until recently, for the most part been wasted.

Jan 1, 1937

By G. Bhat, J. F. Libsch

A STUDY of the kinetics of embrittlement in engineering alloy steels during tempering has indicated that the presence of alloying elements may define two distinct regions of embrittlement: 1) at 800° to 1000 °F, termed low temperature embrittle-ment, and 2) in the temperature range 1150 ° to 1250°F, termed high temperature embrittlement.13 It has been suggested that embrittlement in each region may be due to a different mechanism. At intermediate temperatures and extended times the course of embrittlement may be influenced by the superposition of the embrittlement occurring in the two regions. Furthermore, low temperature embrittlement has been known to decrease as the temperature is raised slightly above the maximum embrittlement range.' Jaffe and BuffumV ave presented data for a Ni-Cr steel illustrating the removal of the em-brittlement occurring at 932°F by reheating to 1250°F for an hour. Their data further shows that embrittlement proceeds continuously with increased time at 1250°F, becoming pronounced at long times. They interpreted this behavior as a retrogression phenomenon involving the solution of the small nuclei of precipitate formed at 932°F as the temperature was increased, and reprecipitation of larger nuclei stable at 1250°F, with the reoccurrence of embrittlement. It appears desirable to reconsider this explanation in the light of the two regions of embrittlement proposed by the authors1 for some alloy steels. In addition, it appears desirable to determine any influence of a preconditioning treatment in each temperature range upon subsequent development of low and high temperature embrittlement. It is thus the object of this investigation to study the characteristics of the two modes of embrittlement proposed in a commercial Ni-Cr alloy steel (AISI 3140). Experimental Details Material—The material used in this investigation was commercial AISI 3140 steel bar stock, received as % in. hot-rolled rounds. The steel analysis was as follows (in percentages): C, 0.39; Mn, 0.79; Si, 0.30; S, 0.028; P, 0.015; Ni, 1.26; and Cr, 0.77. Material Processing and Heat Treatment—The bar stock was first ground to 0.430 in. squares and cut into specimens 23/4 in. long. These specimens were austenitized at 1650°F for 1 hr and oil

Jan 1, 1958